search for: pii

Hi, all Did anyone tried TDM400 card on old main board (Intel 440LX chipset -- PII)? The reason I am asking is because TDM400 needs PCI2.2 and main board is PCI2.1 I do not want to upgrade yet. Thanks, Rudolf

Tested floppy boot on two machines (one PII 350, one 486DX4) Floppy boot with syslinux is very very slow, more than 18 mn to boot a linux kernel from floppy on the 2 machines. Tested with 3 different disquettes that were know to work, boot is reached after this very long time. Noise from floppy head make think floppy wait approximatly one m...

> Could you please try with a Debian kernel image There is one? I do not find it in either etch or sid (or on Alioth). Do I have to recompile a kernel?

Hello, I''m going to be helping a friend setup Shorewall in place of his Cisco router on his home network. Shorewall will be acting as the router/firewall gateway for internet access for his home LAN. His connection to the ISP is via PPPOE. Nothing unfamiliar here to me. It will be a standard 2 interface setup. My curiosity was peaked when he said that he is going to be installing

Hi, all I am doing "prrof of concept" system. I will have two IP phones connected to Asterisk box. Box itself will have 1 PSTN conenction and one analog phone conenction. A basic minimal configuration. At the moment I am planning to use an old PII-350 with 128M of RAM I have lying around. I can not test anything yet, as I am waiting for phones to arrive, so question is will that be enough to demonstrate? Thanks, Rudolf

Hi! I have moved our samba configuration to a new hardware. Old config: PII 266 MHz 96MB memory RedHat 7.2 20Gb ide hard drive for samba shares samba-*-2.2.7-3.7.2 packages installed kernel-2.4.20-28.7 New config: P4 2.4GHz 512MB memory RedHat 9.0 60GB scsi hard drive for samba shares and OS 40GB ide hard drive for backups samb...

...chunk before sending an ack. This causes huge protocol overhead and the data rate falls through the floor. I suspect a number of the reported performance problems in this list are related to this - people tend to stick Linux and Samba on an old 486 then use this to serve an office full of brand new PIIs running WNT. Why the performance figures for the 3c509 were so much better I haven't a clue, unless the fact that it was an ISA card slowed the data rate sufficiently to minimise the windowing problem? Best regards, Paul Paul Sherwin Consulting 22 Monmouth Road, Oxford OX1 4TD, UK Phone...

...ender the original HDD data >> effectively irretrievable. > > so a single pass of zeros is plenty adequate for casual use, and > physical device destruction is the only approved method for anything > actually top secret. Not dealing with "secret", dealing with HIPAA and PII data. And *sigh* Homeland Security Theater dictates.... mark

Hi, i am seeing an oops (every couple of days) on a UP PII system with SCSI disks, Kernel 2.2.19 and ext3 0.0.6b. All oops output passed the klogd thus i cant anymore pipe it through ksymoops - I ensured klogd got the correct System.map so the result should be reliable. Apr 25 17:03:10 Unable to handle kernel paging request at virtual address 8efd1fc...

Hi. I have 2 PC's connected with 1GBit NIC's. When I transfer a file from my File-Server(Redhat9.0, 256 SD-RAM, 300MHz PII, RTL8169 NIC, 2x Western Digital WD200JB RAID 0) to my Windows-PC(AMD Athlon XP 1800+, 1024 MB DDR-RAM, WINXP PRO, RTL8169 NIC, 2x Western Digital WD080JB RAID 0) with Samba, i get Speeds around 8-9MB/sec. I think this is too low for an GBit Network, so i tested the NIC's with the Tool Iperf (h...

...ior. Just in case i am adding here all the xen packages i have installed : ii libc6-xen 2.3.6.ds1-8 GNU C Library: Shared libraries [Xen version ii linux-image-2.6.18-2-xen-686 2.6.18-5 Linux 2.6.18 image on PPro/Celeron/PII/PIII/ ii linux-modules-2.6.18-2-xen-686 2.6.18-5 Linux 2.6.18 modules on PPro/Celeron/PII/PII ii xen-hypervisor-3.0-unstable-1-i386 3.0-unstable+hg11561-1 The Xen Hypervisor on i386-class rc xen-hypervisor-3.0.3-1-i386 3.0.3-0-2 Th...

...correct? (still, 10mbit should be plenty). I'm a bit at a loss where to start debugging - I've tried to play with the voice frames per TX parameter (but as I'm experiencing drops on RX...), the order of codecs (lowest bandwdith first), but it doesn't seem to make a difference. A PII/400 should be enough to do codec translation on one call in any case, so I feel that whatever I tune, it's just fiddling and doesn't get to the real problem. However, I don't have the faintest idea about where to start looking for the real problem. What could cause drops on such a LAN...

I'm running RedHat 7.2 (kernel 2.4.17) on a PII 300. I'm using Liveice with XMMS. I had no problem broadcasting with Shoutcast and Winamp back before I switched over to Linux. I'd love to get going on broadcasting... but Icecast refusing to open is a problem. Running icecast gives me the following. Starting thread engine... [04/Feb/200...

...ts of affected files are radically different. We've been able to demonstrate this happening on directories containing as few as 23 files, 20 MB. Tests using smbclient binary from samba 1.9.18p10 indicate that the 1.9.18p10 version of smbclient does not demonstrate this flaw. Our Setups: Dual PII-450 \ Linux kernel 2.2.9, gcc 2.7.2.3, Intel NIC Dual PII-233 \ Linux kernel 2.2.9, gcc 2.7.2.3, Intel NIC Dual P-133 \ Linux kernel 2.0.36, gcc 2.7.2.3, Intel NIC P-233 \ Linux kernel 2.0.36, gcc 2.7.2.3, 3Com NIC Dual PII-233, NT 4.0 Server, SP3, Intel NIC K6-2 300, NT 4.0 Workstation, SP4, 3Com...

Newbee here.... I would like to play around with Asterisk a little. First, I need to prepare a server with FreeBSD. It's a PII 433mHz/256mb box. Good enough? Then install Asterisk. I have a broadband (cable) internet presence. Could I do anything with this connection and Asterisk? Thanks, Rayasterisk --------------------------------- Do you Yahoo!? Read only the mail you want - Yahoo! Mail SpamGuard. ------------...

Has anyone successfully run asterisk with a VIA processor ? I have tried unsucessfully, do I have to run make with any specific switches ?

I'm thinking of placing Asterisk on an itx motherboard in a tiny case. The ITX motherboards top out around 400Mhz PII (in terms of power relative to a desktop). How much CPU would I need for an office of 50 people? How much disk storage for voicemail + OS? (typical / average) The system will have no PCI cards (no Digium FSO/FXO cards) - everything over the LAN connection. Thanks, Mike -------------- next...

Hi, I am going to set up an office of 30 employees and since it's the first time I thought I will ask for suggestions (trying to make a CentOS base office :) ). I was planning to re use an old Compaq LPr PII 450, sw mirrored scsi 10000rpm disks, 448Mb RAM, to build a CentOS based firewall and I was wondering if this hardware would be enough to serve 30 clients (I already have a centos firewall serving 8 users on a PC celeron 1,3Ghz machine and top shows average load 0.00). The other service they...

...malfunctions, so I switched to Linux. The machine is usable under Linux, but I still think that number of interrupts per second is a bit high. My motherboard is an Abit BE6, and it seems to have some IRQ assignment problems, so I'm wondering what my baseline should be. Also, I have a dual CPU PII motherboard with two X100P cards in it, and it's hitting about 1000 interrupts per second per card too. Is this normal? How many interrupts per second can a given CPU sustain? Thanks! -- Jesse Guardiani, Systems Administrator WingNET Internet Services, P.O. Box 2605 // Cleveland, TN 37320-26...

On Mon, 4 Feb 2002, Jack Moffitt wrote: > > I'm running RedHat 7.2 (kernel 2.4.17) on a PII 300. I'm using Liveice > > with XMMS. I had no problem broadcasting with Shoutcast and Winamp back > > before I switched over to Linux. I'd love to get going on broadcasting... > > but Icecast refusing to open is a problem. > > Did you use the hostname parameter in t...