search for: fxol

So far it happened two (2) times, last time yesterday. Opened case with Asterisk https://issues.asterisk.org/jira/browse/ASTERISK-24593 All FXO channels went off-hook, Operator FXS was constantly ringing. If I picked a handset there was a dead silence. If I put it back on hook it would start ringing. FreePBX interface would not operate properly. Specifically it was slow to authenticate, then

...ideas? Thanks, Andy /etc/dahdi/system.conf # Autogenerated by /usr/sbin/dahdi_genconf on Wed Jun 10 22:20:05 2009 -- do not hand edit # Dahdi Configuration File # # This file is parsed by the Dahdi Configurator, dahdi_cfg # # Span 1: WCTDM/4 "Wildcard TDM400P REV E/F Board 5" (MASTER) fxols=1 #echocanceller=mg2,1 fxols=2 #echocanceller=mg2,2 # channel 3, WCTDM/4/2, no module. fxsks=4 echocanceller=mg2,4 # Global data loadzone = us defaultzone = us dahdi show status Description Alarms IRQ bpviol CRC4 Fra Codi Options LBO Wildcard TDM4...

...(Default) (Slaves: 01) Channel 02: FXS Kewlstart (Default) (Slaves: 02) Channel 03: FXS Kewlstart (Default) (Slaves: 03) Channel 04: FXS Kewlstart (Default) (Slaves: 04) 4 channels to configure. cat /proc/zaptel/* says: Span 1: WCTDM/0 "Wildcard TDM400P REV I Board 1" 1 WCTDM/0/0 FXOLS 2 WCTDM/0/1 FXSKS 3 WCTDM/0/2 FXSKS 4 WCTDM/0/3 FXSKS /etc/zaptel.conf is: # Span 1: WCTDM/0 "Wildcard TDM400P REV I Board 1" fxols=1 fxsks=2 fxsks=3 fxsks=4 # Global data loadzone = au defaultzone = au I have Googled for help but not found anything. Does anyone have a...

...ngly enough I have everything compiled correctly and installed. I am running a TDM400P, Port 1 FXS, Port 4 FXO. I have my PSTN line plugged into 1 port and my Analogue phone plugged into port 4 (I think that's right I get tone on the phone when I pick it up and echo works). /etc/zaptel.conf fxols=1 fxsls=4 ; Weird but I was told to have the fxols fxsls reverse to the actually module loadzone = au defaultzone = au /etc/zapata.conf [channels] context=default switchtype=national usecallerid=yes hidecallerid=no callwaiting=no usecallingpres=yes callwaitingcallerid=yes threewaycalling=yes tra...

...# are handled by the userspace library). # "fxsls" : Channel(s) are signalled using FXS Loopstart protocol. # "fxsgs" : Channel(s) are signalled using FXS Groundstart protocol. # "fxsks" : Channel(s) are signalled using FXS Koolstart protocol. # "fxols" : Channel(s) are signalled using FXO Loopstart protocol. # "fxogs" : Channel(s) are signalled using FXO Groundstart protocol. # "fxoks" : Channel(s) are signalled using FXO Koolstart protocol. # "sf" : Channel(s) are signalled using in-band single fre...

I have one TDM2404E digium card on asterisk box, after configuring the zaptel and zapata configuration files, I am getting these errors when reloading asterisk: ast_unregister_indication_country: Removed default indication country 'us' setup_zap: Ignoring signalling setup_zap: Ignoring answeronpolarityswitch unable to recognize channel 13-5 what is the reason for that? Thanks,

...------- blacklist hisax blacklist hisax_fcpcipnp blacklist 8139cp blacklist hfc4s8s_l1 ------------------------------ The /etc/zaptel.conf file looks like this: --------------------- zaptel.conf ----------------------------- # Span 1: WCTDM/0 "Wildcard TDM400P REV I Board 1" fxsks=1 fxols=2 fxsks=3 fxols=4 # Span 2-5: Junghans span=2,1,3,ccs,ami span=3,0,3,ccs,ami span=4,0,3,ccs,ami span=5,0,3,ccs,ami bchan=5,6 dchan=7 bchan=8,9 dchan=10 bchan=11,12 dchan=13 bchan=14,15 dchan=16 # Global data loadzone = fr defaultzone = fr ----------------------------------------...

...leaves line in use until it is shutdown. 2. When calling an analog phone connected to channel bank the phone doesn't ring. If you are in call and some else calls the extension you get the call waiting tones and a flash works to flip to the new line. zaptel.conf span=1,1,0,esf,b8zs fxsls=13-24 fxols=1-12 loadzone = us defaultzone=us zapata.conf [channels] context = local language = en callwaiting = yes threewaycalling = yes transfer = yes cancelforward = yes callreturn = no usecallerid = yes hidecallerid = no echocancel = yes echocancelwhenbridged = yes ;immediate = no txgain=1.0 rxgain=1.0...

...yes relaxdtmf=yes rxgain=0.0 txgain=0.0 group=1 callgroup=1 pickupgroup=1 immediate=no ;Sangoma A101 port 1 [slot:8 bus:3 span: 1] context=from-pstn group=0 signalling=fxo_ls channel => 1-6 zaptel.conf loadzone=us defaultzone=us #Sangoma A101 port 1 [slot:8 bus:3 span: 1] span=1,1,0,esf,b8zs fxols=1-6 Extensions.conf [from-pstn] exten => _X.,1,Dial(zap/3/603xxxxxxx); Very simple setup at this moment, nothing fancy. I am able to dial in via sip and asterisk answers and send the call to the from-pstn context at which point i see Executing Dial(blah, blah) in new stack; I believe at th...

...are handled by the userspace library). # "fxsls" : Channel(s) are signalled using FXS Loopstart protocol. # "fxsgs" : Channel(s) are signalled using FXS Groundstart protocol. # "fxsks" : Channel(s) are signalled using FXS Koolstart protocol. # "fxols" : Channel(s) are signalled using FXO Loopstart protocol. # "fxogs" : Channel(s) are signalled using FXO Groundstart protocol. # "fxoks" : Channel(s) are signalled using FXO Koolstart protocol. # "sf" : Channel(s) are signalled using in-band single f...

...# are handled by the userspace library). # "fxsls" : Channel(s) are signalled using FXS Loopstart protocol. # "fxsgs" : Channel(s) are signalled using FXS Groundstart protocol. # "fxsks" : Channel(s) are signalled using FXS Koolstart protocol. # "fxols" : Channel(s) are signalled using FXO Loopstart protocol. # "fxogs" : Channel(s) are signalled using FXO Groundstart protocol. # "fxoks" : Channel(s) are signalled using FXO Koolstart protocol. # "sf" : Channel(s) are signalled using in-band single fre...

...are handled by the userspace library). # "fxsls" : Channel(s) are signalled using FXS Loopstart protocol. # "fxsgs" : Channel(s) are signalled using FXS Groundstart protocol. # "fxsks" : Channel(s) are signalled using FXS Koolstart protocol. # "fxols" : Channel(s) are signalled using FXO Loopstart protocol. # "fxogs" : Channel(s) are signalled using FXO Groundstart protocol. # "fxoks" : Channel(s) are signalled using FXO Koolstart protocol. # "sf" : Channel(s) are signalled using in-band single...

I can either get the TE100P working or the 3 X100P clones working, but never both. I have the TE100P connected to a channel bank, and X100P clones to lines from the phone company. This is my zaptel.conf span=1,1,0,d4,ami fxsks=1-24 loadzone=us fxols=25-27 loadzone=us I then do [root@asterix root]# modprobe zaptel [root@asterix root]# modprobe wcte11xp ZT_CHANCONFIG failed on channel 25: No such device or address (6) /lib/modules/2.4.20-8/misc/wcte11xp.o: post-install wcte11xp failed /lib/modules/2.4.20-8/misc/wcte11xp.o: insmod wcte11xp f...

...# are handled by the userspace library). # "fxsls" : Channel(s) are signalled using FXS Loopstart protocol. # "fxsgs" : Channel(s) are signalled using FXS Groundstart protocol. # "fxsks" : Channel(s) are signalled using FXS Koolstart protocol. # "fxols" : Channel(s) are signalled using FXO Loopstart protocol. # "fxogs" : Channel(s) are signalled using FXO Groundstart protocol. # "fxoks" : Channel(s) are signalled using FXO Koolstart protocol. # "sf" : Channel(s) are signalled using in-band single freq...

I'm having trouble with a WX100USB adapter and a Siemens Gigaset cordless phone. If I select fxols as a signalling method, calls are being disconnected. Usually after about 4 minutes, and asterisk just says that the phone has hung up. If I choose fxogs, I immediately get a LINE IN USE message on my phone and I can't even get a dialtone. If I choose fxoks, it mostly works, but sometimes af...

...:41 WARNING[11441]: We're Zap/1-1, not H8?F??n** May 24 14:52:41 WARNING[11441]: We're Zap/1-1, not H8?F??n** May 24 14:52:41 WARNING[11441]: We're Zap/1-1, not H8?F??n** Any ideas are welcome! Thanks in advance. Jorge These are my config files: /etc/zaptel.conf span=1,1,0,esf,b8zs fxols=1-24 span=2,1,0,esf,b8zs fxols=25-37 fxsls=49-52 defaultzone=us loadzone=us etc/asterisk/zapata.conf [channels] language = es signalling = fxo_ls usecallerid = yes echocancel = yes echotraining = yes echocancelwhenbridged = yes rxgain = 0 txgain = 0 musiconhold = Default busydetect = yes busyc...

Hi, all I have installed TDM400 with 1 FXS and 1 FXP ports. Now I am goig through documentation on how to configure it. It mentions 3 protocols: Loopstart, Groundstart and Koolstart. Which one do I use? Can someone send me sample zaptel.conf file for Australia? This will save me some time and will be used as a working example. Thanks, Rudolf

Hi i have buy a Digium TDM400P with 1 fxo modules TDM01B for connect my asterisk to a french analog line. In my zaptel.conf, i have: loadzone=fr defaultzone=fr fxols=3 when i load the module, i have in logs: Nov 24 06:13:40 gw kernel: Freed a Wildcard Nov 24 06:13:40 gw kernel: Zapata Telephony Interface Unloaded Nov 24 06:13:40 gw zaptel: Removing zaptel module: succeeded Nov 24 06:13:42 gw kernel: Zapata Telephony Interface Registered on major 196 Nov 24 0...

Is there a way to test if the motherboard is ready for a Digium card (PCI 2.2) ? I would like to know from a remote computer, where I have (root) access, if this computer is ready for a TDM22B. bye Ronald

...ard goes into yellow alarm and won't sync up. the only errors we see are framing slips. Around 2500 slips over a 18 hour period. (this was reported from our T-Berd) Any thoughts ??? -------------------------------------- Here is our /etc/zaptel.conf span=1,0,0,esf,b8zs bchan=1-4 dchan=24 fxols=25 -------------------------------------- here is .../asterisk/zapata.conf [channels] context=espire-pri-in switchtype=national pridialplan=national usecallerid=yes callerid=asreceived hidecallerid=no callwaiting=yes callwaitingcallerid=yes threewaycalling=yes transfer=yes cancallforward=ye...