Is there a way to test if the motherboard is ready for a Digium card (PCI 2.2) ? I would like to know from a remote computer, where I have (root) access, if this computer is ready for a TDM22B. bye Ronald
Only way that I know is to open the case and look at the slot to see if there are two dividers. I would be interested in knowing this as well. ----- Original Message ----- From: "Ronald Wiplinger" <ronald@elmit.com> To: "Asterisk Users Mailing List - Non-Commercial Discussion" <asterisk-users@lists.digium.com> Sent: Saturday, November 27, 2004 7:31 PM Subject: [Asterisk-Users] How to test if PCI 2.2?> Is there a way to test if the motherboard is ready for a Digium card > (PCI 2.2) ? > > I would like to know from a remote computer, where I have (root) access, > if this computer is ready for a TDM22B. > > bye > > Ronald > > _______________________________________________ > Asterisk-Users mailing list > Asterisk-Users@lists.digium.com > http://lists.digium.com/mailman/listinfo/asterisk-users > To UNSUBSCRIBE or update options visit: > http://lists.digium.com/mailman/listinfo/asterisk-users >
Leo Ann Boon wrote:> >> Asterisk dies with unable to specify channel 1: No such device or >> address >> >> When I try ztfg -vv I get: >> Zaptel Configuration >> ==============>> >> Channel map: >> 0 channels configured. >> > Did you configure /etc/zaptel.conf? Digium cards must be configured at > 2 locations /etc/zaptel.conf and /etc/asterisk/zapata.conf. And make > sure your /etc/modules.conf have: > post-install wctdm /usr/sbin/ztcfgyes, it is there. ; zaptel.conf loadzone=tw defaultzone=tw fxols=1-2 ; FXS modules (fxols -> FXS module) fxsls=3-4 ; FXO modules (fxsls -> FXO module)
When I cat /var/log/dmesg | grep PCI, I get this: PCI: PCI BIOS revision 2.10 entry at 0xfc7ce, last bus=1 PCI: Using configuration type 1 PCI: Probing PCI hardware PCI: Discovered primary peer bus 01 [IRQ] PCI: Using IRQ router ServerWorks [1166/0200] at 00:0f.0 Serial driver version 5.05c (2001-07-08) with MANY_PORTS MULTIPORT SHARE_IRQ SERIAL_PCI ISAPNP enabled SvrWks OSB4: IDE controller at PCI slot 00:0f.1 PCI: Found IRQ 10 for device 01:02.0 PCI: Found IRQ 15 for device 01:02.1 scsi0 : Adaptec AIC7XXX EISA/VLB/PCI SCSI HBA DRIVER, Rev 6.2.36 scsi1 : Adaptec AIC7XXX EISA/VLB/PCI SCSI HBA DRIVER, Rev 6.2.36 PCI: Assigned IRQ 5 for device 00:0f.2 Does this first line confirm that I am PCI 2.1. I tried it on several machines that I have access to and they all say 2.10. I recognize that this means I'm out of luck for a TDM4xx card, but is this an accurate enough test or might the OS be somehow fibbing? dbc.> Message: 5 > Date: Sun, 28 Nov 2004 08:31:47 +0800 > From: Ronald Wiplinger <ronald@elmit.com> > Subject: [Asterisk-Users] How to test if PCI 2.2? > To: Asterisk Users Mailing List - Non-Commercial Discussion > <asterisk-users@lists.digium.com> > Message-ID: <41A91C73.4050306@elmit.com> > Content-Type: text/plain; charset=us-ascii; format=flowed > > Is there a way to test if the motherboard is ready for a Digium card > (PCI 2.2) ? > > I would like to know from a remote computer, where I have (root) > access, > if this computer is ready for a TDM22B. > > bye > > Ronald