search for: emdigitwait

Hello all. I just received a TE110P and am trying to hook it to my Mitel 200SX has anyone successfully done this? My configuration is as follows. Asterisk -> TE110P ->Kentrox (csu/dsu) -> Mitel T1 Card. All I get is a blinking yellow on my TE110P card and an alarm on my Mitel. T1 card. Any advice would be great. Zaptel.conf span=1,0,1,d4,ami e&m=1-23 dchan=24

hi. i connected Asterisk to an NEC NEAX system with a crossover T1 cable and the Digium TE405P using E&M wink signaling. the connection's ok. however when dialing from the NEC to the Asterisk. most of the time the Asterisk only sees the first digit of the dialed number(which is 4 digits). some time if i dialed the 4 digits very fast it might get through. seems like there's a timming

I'm trying to get a patch tested for inclusion in CVS. Anyone that is running E&M on a T1 and had to fool around with emdigitwait could you please try this. This patch removes the need for the emdigitwait parameter and speeds up dialing. This situation is mostly interfacing a legacy PBX/Key system with Asterisk. I've been running a couple of systems with this patch for about 6 months without problem. Please see...

...to fix it? zaptel.conf: span=1,1,0,esf,b8zs bchan=1-23 dchan=24 loadzone = us span=2,1,0,esf,b8zs e&m=25-48 span=3,1,0,esf,b8zs e&m=49-72 loadzone = us defaultzone=us zapata.conf: [channels] group = 0 switchtype=national signalling=pri_cpe channel=>1-23 group = 1 context=from-trunk emdigitwait=2500 signalling=em_w rxwink=300 usecallerid=yes immediate=no overlapdial=yes channel=>25-72 Any help is appreciated. -- Derek Fedel

Does anyone know the default E&M Wink timings for Nortel DID ports? The default settings on Asterisk are: ; prewink: Pre-wink time (default 50ms) ; preflash: Pre-flash time (default 50ms) ; wink: Wink time (default 150ms) ; flash: Flash time (default 750ms) ; start: Start time (default 1500ms) ; rxwink: Receiver wink time (default 300ms) ;

We're having some difficulty connecting a T1 fax board card to asterisk, with E&M Wink. We've successfully connected it to other E&M Wink T1s, but have been unable to get asterisk to hear it's dialing. Asterisk can dial down to it with no problem, and it hears all the digits, but whenever it sends digits down to asterisk, * always only "gets" the first one. This is

Hi again, I'm trying to setup our non pri T1 (they call it a Long Distance T1), our current pbx has the signaling set to E&M, I can set em in zapata.conf, but I'm trying to track down the proper entries for the zaptel.conf file. The digium docs only show a PRI example. Our current system has these settings: Signalling: E&M Framing mode: ESF Line Coding: B8SZ here's my

Hello - I have a non-PRI T1 setup and have been making outgoing calls for several months no problem. I have Zapata.conf setup for fxs_ks on these channels. How do I take incoming calls on these same channels? Do I need to change the signaling? Any help is appreciated. Thank you, Dave -------------- next part -------------- An HTML attachment was scrubbed... URL:

We are having line noise issues in our Asterisk to legacy PBX integration. All SIP calls originating from IP phones sound crystal clear. All calls that originate from the legacy PBX (Isoetec 228) and route through the Asterisk and out SIP have a lot of line noise. I believe I have it pinned down to these Blue Alarm errors that I can see on the legacy PBX side. zttool shows no alarm but when I