search for: autoswitch

...rver is connected to outlet.0 and properly shuts down when it's loosing power after around 20 minutes. It also boots up whenever the ups is getting power again. To outlet.1 there are a few components like a router, a small switch and a phone connected. As to our understanding of , outlet.1.autoswitch.charge.low and outlet.1.switchable it should be possible to power off these devices at a given battery charge, right? However, using upsrw or upsset.cgi results in strange behaviour. Setting (ups|outlet.x).delay.(shutdown|start) to e.g. 120 returns some random value (102, 68, etc.). The value r...

...down.. Whats the lowest number to safely set it to shut down? (But then I run into the problem with #1. 3) Most of the values in UPSlog are NA, such as input voltage, ups.load (Though I did see it say 4 ONCE, temp and input frequency. When I do a "upsrw" I get : [outlet.0.desc] [outlet.1.autoswitch.charge.low] [outlet.1.desc] [outlet.1.switch] [ups.delay.shutdown] Is that the ONLY items I can get besides : battery.charge: 0 battery.charge.low: 30 battery.runtime: 00000 driver.name: mge-shut driver.parameter.port: /dev/cuaa0 driver.version: 2.0.3 driver.version.internal: 0.65 outlet.0.desc:...

...00 input.frequency: 59.9 input.frequency.extended: no input.frequency.nominal: 60 input.sensitivity: normal input.transfer.boost.low: 102 input.transfer.high: 151 input.transfer.low: 89 input.transfer.trim.high: 132 input.voltage: 116.7 input.voltage.extended: no input.voltage.nominal: 120 outlet.1.autoswitch.charge.low: 0 outlet.1.current: 3.70 outlet.1.delay.shutdown: 65535 outlet.1.delay.start: 3 outlet.1.desc: PowerShare Outlet 1 outlet.1.id: 1 outlet.1.power: 432 outlet.1.powerfactor: 94.00 outlet.1.realpower: 410 outlet.1.status: on outlet.1.switchable: yes outlet.2.autoswitch.charge.low: 0 outlet...

I am faced with a network that needs to autoswitch to isdn should T-1 go down. After a shorewall search it looks to be quite a deal with routing config with linux. Like scripts written to deal with knowing the T-1 is down. I looked into a cisco router that does this. around $3000 This network has used shorewall as the gateway for 4 years now....

...5 input.frequency: 50.0 input.frequency.extended: no input.frequency.nominal: 50 input.sensitivity: normal input.transfer.boost.low: 184 input.transfer.high: 294 input.transfer.low: 160 input.transfer.trim.high: 265 input.voltage: 238.0 input.voltage.extended: no input.voltage.nominal: 230 outlet.1.autoswitch.charge.low: 0 outlet.1.delay.shutdown: 65535 outlet.1.delay.start: 3 outlet.1.desc: PowerShare Outlet 1 outlet.1.id: 1 outlet.1.status: on outlet.1.switchable: yes outlet.2.autoswitch.charge.low: 0 outlet.2.delay.shutdown: 65535 outlet.2.delay.start: 6 outlet.2.desc: PowerShare Outlet 2 outlet.2.id...

...2.0.4 driver.version.data: MGE HID 0.9 driver.version.internal: 0.28 input.frequency: 0.0 input.transfer.boost.low: 184.0 input.transfer.high: 294.0 input.transfer.low: 160.0 input.transfer.trim.high: 265.0 input.voltage: 0.0 outlet.0.desc: Main Outlet outlet.0.id: 0 outlet.0.switchable: 0 outlet.1.autoswitch.charge.low: 0 outlet.1.delay.shutdown: -1 outlet.1.delay.start: -1 outlet.1.desc: PowerShare Outlet 1 outlet.1.id: 1 outlet.1.switch: 1 outlet.1.switchable: 1 outlet.2.autoswitch.charge.low: 0 outlet.2.delay.shutdown: -1 outlet.2.delay.start: -1 outlet.2.desc: PowerShare Outlet 2 outlet.2.id: 2 out...

.... Asterisk versions from 0.7.2 to 1.0.3. Results have been consistently flaky, I've tried flash upgrading, makes no difference. Have tried all sorts of config tweaks on the phone as to buffer size, etc. Google has almost NO info on these things, they have one nice feature which is easy autoswitching between POTS and SIP calls in both directions. Any experience or hearsay out there in Asterisk land?

...: 120 driver.parameter.ondelay: 13 driver.parameter.pollinterval: 2 driver.parameter.port: auto driver.version: 2.2.0 driver.version.data: MGE HID 1.0 driver.version.internal: 0.30 input.frequency: 50.0 input.voltage: 243.0 outlet.0.desc: Main Outlet outlet.0.id: 0 outlet.0.switchable: yes outlet.1.autoswitch.charge.low: 0 outlet.1.delay.shutdown: 2592000 outlet.1.delay.start: 1 outlet.1.desc: PowerShare Outlet 1 outlet.1.id: 1 outlet.1.status: off outlet.1.switchable: yes outlet.2.autoswitch.charge.low: 0 outlet.2.delay.shutdown: 2592000 outlet.2.delay.start: 1 outlet.2.desc: PowerShare Outlet 2 outlet...

...servers (Asterisk, Trixbox, FreePBX, etc) auto switch between the best rest rate? --Can people's VoIP phones be a part of several extensions (on different VoIP solutions)? --Say about 10-20 of us want a virtual receptionist, and want to rotate them so that calls work in different times zones (autoswitch on certain times, auto go to a different receptionist if one is busy, etc). Where might I look to think about this? --Google Voice will not forward texts and calls to foreign numbers, so what type of solution would I need to accept calls (to a US number) and then forward the texts / calls to fore...

...m not that sure about nut configuration. First of all I think I have to use upssched for shutting down the computers, both connected to the programmable outlets, haven't I? But how does the driver communicate to the computers that outlet.X is cutting the power since is reaching the outlet.X.autoswitch.charge.low/outlet.X.delay.shutdown condition? Does it cut the power without any notice? And how the computers get aware from witch outlet they are drawing power? Without these information it sounds that programmable outlets are almost unuseful and just marketing. I mean, if I have to set up a c...

...no > input.frequency.nominal: 50 > input.sensitivity: normal > input.transfer.boost.low: 184 > input.transfer.high: 294 > input.transfer.low: 160 > input.transfer.trim.high: 265 > input.voltage: 233.0 > input.voltage.extended: no > input.voltage.nominal: 230 > outlet.1.autoswitch.charge.low: 0 > outlet.1.delay.shutdown: 65535 > outlet.1.delay.start: 3 > outlet.1.desc: PowerShare Outlet 1 > outlet.1.id: 1 > outlet.1.status: on > outlet.1.switchable: yes > outlet.2.autoswitch.charge.low: 0 > outlet.2.delay.shutdown: 65535 > outlet.2.delay.start: 6 &...

...er.parameter.port: /dev/cuau1 driver.version: 2.6.5-Unversioned directory driver.version.data: MGE HID 1.31 driver.version.internal: 0.37 input.bypass.current: 0.00 input.bypass.voltage: 224.0 input.frequency: 50.0 input.frequency.nominal: 50 input.voltage: 224.0 input.voltage.nominal: 230 outlet.1.autoswitch.charge.low: 0 outlet.1.delay.shutdown: 65535 outlet.1.delay.start: 3 outlet.1.desc: PowerShare Outlet 1 outlet.1.id: 1 outlet.1.status: on outlet.1.switchable: yes outlet.2.autoswitch.charge.low: 0 outlet.2.delay.shutdown: 0 outlet.2.delay.start: 2146379092 outlet.2.desc: PowerShare Outlet 2 outlet...

...2.1.0 +driver.version.data: MGE HID 1.0 +driver.version.internal: 0.30 input.frequency: 60.0 input.transfer.boost.low: 102.0 input.transfer.high: 151.0 @@ -16,26 +18,26 @@ input.voltage: 121.0 outlet.0.desc: Main Outlet outlet.0.id: 0 -outlet.0.switchable: 0 +outlet.0.switchable: no outlet.1.autoswitch.charge.low: 0 outlet.1.delay.shutdown: 65535 -outlet.1.delay.start: 65535 +outlet.1.delay.start: 3 outlet.1.desc: PowerShare Outlet 1 outlet.1.id: 1 -outlet.1.switch: 1 -outlet.1.switchable: 1 +outlet.1.status: on +outlet.1.switchable: yes outlet.2.autoswitch.charge.low: 0 outlet.2.delay.shutd...

...mge@localhost battery.charge: 78 battery.charge.low: 20 battery.runtime: 05760 driver.name: mge-shut driver.parameter.port: /dev/cuad1 driver.version: 2.0.3 driver.version.internal: 0.65 input.frequency: 50 input.voltage: 237 outlet.0.desc: Main Outlet outlet.0.id: 0 outlet.0.switchable: 0 outlet.1.autoswitch.charge.low: 0 outlet.1.delay.shutdown: -1 outlet.1.delay.start: -1 outlet.1.desc: PowerShare Outlet 1 outlet.1.id: 1 outlet.1.switch: 1 outlet.1.switchable: 1 outlet.2.autoswitch.charge.low: 0 outlet.2.delay.shutdown: -1 outlet.2.delay.start: -1 outlet.2.desc: PowerShare Outlet 2 outlet.2.id: 2 out...

...whidups driver.parameter.offdelay: 180 driver.parameter.ondelay: 30 driver.parameter.port: auto driver.version: 2.0.5 driver.version.data: MGE HID 1.0 driver.version.internal: 0.30 input.frequency: 50.0 input.voltage: 232.0 outlet.0.desc: Main Outlet outlet.0.id: 0 outlet.0.switchable: yes outlet.1.autoswitch.charge.low: 0 outlet.1.delay.shutdown: 2147483648 outlet.1.delay.start: 3 outlet.1.desc: PowerShare Outlet 1 outlet.1.id: 1 outlet.1.status: on outlet.1.switchable: yes outlet.2.autoswitch.charge.low: 0 outlet.2.delay.shutdown: 2147483648 outlet.2.delay.start: 6 outlet.2.desc: PowerShare Outlet 2 o...

...whidups driver.parameter.offdelay: 180 driver.parameter.ondelay: 30 driver.parameter.port: auto driver.version: 2.0.5 driver.version.data: MGE HID 1.0 driver.version.internal: 0.30 input.frequency: 50.0 input.voltage: 232.0 outlet.0.desc: Main Outlet outlet.0.id: 0 outlet.0.switchable: yes outlet.1.autoswitch.charge.low: 0 outlet.1.delay.shutdown: 2147483648 outlet.1.delay.start: 3 outlet.1.desc: PowerShare Outlet 1 outlet.1.id: 1 outlet.1.status: on outlet.1.switchable: yes outlet.2.autoswitch.charge.low: 0 outlet.2.delay.shutdown: 2147483648 outlet.2.delay.start: 6 outlet.2.desc: PowerShare Outlet 2 o...

Hi Dag 2010/2/28 Dag Atle Nettum <dagatle at innit.no> > Hello > > > > I understand you are the project leader of Nut. > > > > In my company we have a Eaton 9135 6000 UPS, we are running NUT 2.4.1 > (Debian squeeze) > > > > The ups is connected with a USB cable but it reports a temperature of 300 > degredes. > > > > Can I send you

...0 input.frequency: 49.9 input.frequency.extended: no input.frequency.nominal: 50 input.sensitivity: normal input.transfer.boost.low: 184 input.transfer.high: 294 input.transfer.low: 160 input.transfer.trim.high: 265 input.voltage: 227.8 input.voltage.extended: no input.voltage.nominal: 230 outlet.1.autoswitch.charge.low: 0 outlet.1.current: 0.00 outlet.1.delay.shutdown: 65535 outlet.1.delay.start: 3 outlet.1.desc: PowerShare Outlet 1 outlet.1.id: 1 outlet.1.power: 0 outlet.1.powerfactor: 0.00 outlet.1.realpower: 0 outlet.1.status: on outlet.1.switchable: yes outlet.2.autoswitch.charge.low: 0 outlet.2.cu...

Hi Powermen ;-) I recently came across the Powerman project (http://sourceforge.net/projects/powerman/), pointed by Tony Merenda, from Opengear (thanks Tony). Congrats for your work in this area! I've thought a bit about Powerman and NUT since then... NUT currently supports hosts of UPSs and few PDUs (RPCs), and provides tons of features: http://test.networkupstools.org

Hello, I've installed Nut (2.0.5) on RedHat a week ago, and upsmon seems to generate false alarms every hour: ... Jun 8 06:10:56 nutevalserver upsmon[2849]: UPS usb-mge-evolution at localhost on line power Jun 8 06:35:46 nutevalserver upsmon[2849]: UPS usb-mge-evolution at localhost on battery Jun 8 06:35:51 nutevalserver upsmon[2849]: UPS usb-mge-evolution at localhost on line power