Anders Nordby
2012-Jul-03 19:05 UTC
bge problems in RELENG_9, bge0: watchdog timeout -- resetting
Hi,
I'm having lots of difficulties with BCM5719, which is the default
network card of HP Proliant DL 360 G8 servers. I can get a few ping
replies before I get a couple of these:
bge0: watchdog timeout -- resetting
bge0: watchdog timeout -- resetting
Then everything hangs. Can not log in using ssh.
I'm running: FreeBSD-9.0-RELENG_9-20120701-JPSNAP-amd64
Info about the NIC:
# devinfo -rv | grep phy
brgphy0 pnpinfo oui=0x1be9 model=0x22 rev=0x0 at phyno=1
brgphy1 pnpinfo oui=0x1be9 model=0x22 rev=0x0 at phyno=2
brgphy2 pnpinfo oui=0x1be9 model=0x22 rev=0x0 at phyno=3
brgphy3 pnpinfo oui=0x1be9 model=0x22 rev=0x0 at phyno=4
# grep bge /var/run/dmesg.boot
bge0: <Broadcom unknown BCM5719, ASIC rev. 0x5719001> mem
0xf6bf0000-0xf6bfffff,
0xf6be0000-0xf6beffff,0xf6bd0000-0xf6bdffff irq 32 at device 0.0 on pci3
bge0: CHIP ID 0x05719001; ASIC REV 0x5719; CHIP REV 0x57190; PCI-E
miibus0: <MII bus> on bge0
bge0: Ethernet address: 2c:76:8a:54:08:14
bge1: <Broadcom unknown BCM5719, ASIC rev. 0x5719001> mem
0xf6bc0000-0xf6bcffff,
0xf6bb0000-0xf6bbffff,0xf6ba0000-0xf6baffff irq 36 at device 0.1 on pci3
bge1: CHIP ID 0x05719001; ASIC REV 0x5719; CHIP REV 0x57190; PCI-E
miibus1: <MII bus> on bge1
bge1: Ethernet address: 2c:76:8a:54:08:15
bge2: <Broadcom unknown BCM5719, ASIC rev. 0x5719001> mem
0xf6b90000-0xf6b9ffff,
0xf6b80000-0xf6b8ffff,0xf6b70000-0xf6b7ffff irq 32 at device 0.2 on pci3
bge2: CHIP ID 0x05719001; ASIC REV 0x5719; CHIP REV 0x57190; PCI-E
miibus2: <MII bus> on bge2
bge2: Ethernet address: 2c:76:8a:54:08:16
bge3: <Broadcom unknown BCM5719, ASIC rev. 0x5719001> mem
0xf6b60000-0xf6b6ffff,
0xf6b50000-0xf6b5ffff,0xf6b40000-0xf6b4ffff irq 36 at device 0.3 on pci3
bge3: CHIP ID 0x05719001; ASIC REV 0x5719; CHIP REV 0x57190; PCI-E
miibus3: <MII bus> on bge3
bge3: Ethernet address: 2c:76:8a:54:08:17
Searching other bug reports and posts, I've tried:
hw.bge.allow_asf="0"
hw.pci.enable_msi="0"
But it didn't help. Any ideas?
If I don't use the loader.conf settings above, I also get (before the
watchdog timeouts):
bge0: 2 link states coalesced
bge0: 2 link states coalesced
bge0: 2 link states coalesced
Best regards,
--
Anders.
Rick Miller
2012-Jul-03 20:04 UTC
bge problems in RELENG_9, bge0: watchdog timeout -- resetting
Hi Anders.... I've not had good luck with the BCM5719 in stable/8 either. Not sure if the driver has been updated in 9 or not, but I have a blog post explaining my woes with the BCM5719 at http://blog.hostileadmin.com/ On 7/3/12, Anders Nordby <anders@freebsd.org> wrote:> Hi, > > I'm having lots of difficulties with BCM5719, which is the default > network card of HP Proliant DL 360 G8 servers. I can get a few ping > replies before I get a couple of these: > > bge0: watchdog timeout -- resetting > > bge0: watchdog timeout -- resetting > > > Then everything hangs. Can not log in using ssh. > > I'm running: FreeBSD-9.0-RELENG_9-20120701-JPSNAP-amd64 > > Info about the NIC: > > # devinfo -rv | grep phy > brgphy0 pnpinfo oui=0x1be9 model=0x22 rev=0x0 at phyno=1 > > brgphy1 pnpinfo oui=0x1be9 model=0x22 rev=0x0 at phyno=2 > > brgphy2 pnpinfo oui=0x1be9 model=0x22 rev=0x0 at phyno=3 > > brgphy3 pnpinfo oui=0x1be9 model=0x22 rev=0x0 at phyno=4 > > # grep bge /var/run/dmesg.boot > bge0: <Broadcom unknown BCM5719, ASIC rev. 0x5719001> mem > 0xf6bf0000-0xf6bfffff, > 0xf6be0000-0xf6beffff,0xf6bd0000-0xf6bdffff irq 32 at device 0.0 on pci3 > > bge0: CHIP ID 0x05719001; ASIC REV 0x5719; CHIP REV 0x57190; PCI-E > > miibus0: <MII bus> on bge0 > > bge0: Ethernet address: 2c:76:8a:54:08:14 > > bge1: <Broadcom unknown BCM5719, ASIC rev. 0x5719001> mem > 0xf6bc0000-0xf6bcffff, > 0xf6bb0000-0xf6bbffff,0xf6ba0000-0xf6baffff irq 36 at device 0.1 on pci3 > > bge1: CHIP ID 0x05719001; ASIC REV 0x5719; CHIP REV 0x57190; PCI-E > > miibus1: <MII bus> on bge1 > > bge1: Ethernet address: 2c:76:8a:54:08:15 > > bge2: <Broadcom unknown BCM5719, ASIC rev. 0x5719001> mem > 0xf6b90000-0xf6b9ffff, > 0xf6b80000-0xf6b8ffff,0xf6b70000-0xf6b7ffff irq 32 at device 0.2 on pci3 > > bge2: CHIP ID 0x05719001; ASIC REV 0x5719; CHIP REV 0x57190; PCI-E > > miibus2: <MII bus> on bge2 > > bge2: Ethernet address: 2c:76:8a:54:08:16 > > bge3: <Broadcom unknown BCM5719, ASIC rev. 0x5719001> mem > 0xf6b60000-0xf6b6ffff, > 0xf6b50000-0xf6b5ffff,0xf6b40000-0xf6b4ffff irq 36 at device 0.3 on pci3 > > bge3: CHIP ID 0x05719001; ASIC REV 0x5719; CHIP REV 0x57190; PCI-E > > miibus3: <MII bus> on bge3 > > bge3: Ethernet address: 2c:76:8a:54:08:17 > > > Searching other bug reports and posts, I've tried: > > hw.bge.allow_asf="0" > > hw.pci.enable_msi="0" > > > But it didn't help. Any ideas? > > If I don't use the loader.conf settings above, I also get (before the > watchdog timeouts): > > bge0: 2 link states coalesced > > bge0: 2 link states coalesced > > bge0: 2 link states coalesced > > > Best regards, > > -- > Anders. > _______________________________________________ > freebsd-stable@freebsd.org mailing list > http://lists.freebsd.org/mailman/listinfo/freebsd-stable > To unsubscribe, send any mail to "freebsd-stable-unsubscribe@freebsd.org" >-- Sent from my mobile device Take care Rick Miller
YongHyeon PYUN
2012-Jul-04 09:01 UTC
bge problems in RELENG_9, bge0: watchdog timeout -- resetting
On Tue, Jul 03, 2012 at 08:57:04PM +0200, Anders Nordby wrote:> Hi, > > I'm having lots of difficulties with BCM5719, which is the default > network card of HP Proliant DL 360 G8 servers. I can get a few ping > replies before I get a couple of these: > > bge0: watchdog timeout -- resetting > bge0: watchdog timeout -- resetting > > Then everything hangs. Can not log in using ssh. > > I'm running: FreeBSD-9.0-RELENG_9-20120701-JPSNAP-amd64 > > Info about the NIC: > > # devinfo -rv | grep phy > brgphy0 pnpinfo oui=0x1be9 model=0x22 rev=0x0 at phyno=1 > brgphy1 pnpinfo oui=0x1be9 model=0x22 rev=0x0 at phyno=2 > brgphy2 pnpinfo oui=0x1be9 model=0x22 rev=0x0 at phyno=3 > brgphy3 pnpinfo oui=0x1be9 model=0x22 rev=0x0 at phyno=4 > # grep bge /var/run/dmesg.boot > bge0: <Broadcom unknown BCM5719, ASIC rev. 0x5719001> mem > 0xf6bf0000-0xf6bfffff, > 0xf6be0000-0xf6beffff,0xf6bd0000-0xf6bdffff irq 32 at device 0.0 on pci3 > bge0: CHIP ID 0x05719001; ASIC REV 0x5719; CHIP REV 0x57190; PCI-E > miibus0: <MII bus> on bge0 > bge0: Ethernet address: 2c:76:8a:54:08:14 > bge1: <Broadcom unknown BCM5719, ASIC rev. 0x5719001> mem > 0xf6bc0000-0xf6bcffff, > 0xf6bb0000-0xf6bbffff,0xf6ba0000-0xf6baffff irq 36 at device 0.1 on pci3 > bge1: CHIP ID 0x05719001; ASIC REV 0x5719; CHIP REV 0x57190; PCI-E > miibus1: <MII bus> on bge1 > bge1: Ethernet address: 2c:76:8a:54:08:15 > bge2: <Broadcom unknown BCM5719, ASIC rev. 0x5719001> mem > 0xf6b90000-0xf6b9ffff, > 0xf6b80000-0xf6b8ffff,0xf6b70000-0xf6b7ffff irq 32 at device 0.2 on pci3 > bge2: CHIP ID 0x05719001; ASIC REV 0x5719; CHIP REV 0x57190; PCI-E > miibus2: <MII bus> on bge2 > bge2: Ethernet address: 2c:76:8a:54:08:16 > bge3: <Broadcom unknown BCM5719, ASIC rev. 0x5719001> mem > 0xf6b60000-0xf6b6ffff, > 0xf6b50000-0xf6b5ffff,0xf6b40000-0xf6b4ffff irq 36 at device 0.3 on pci3 > bge3: CHIP ID 0x05719001; ASIC REV 0x5719; CHIP REV 0x57190; PCI-E > miibus3: <MII bus> on bge3 > bge3: Ethernet address: 2c:76:8a:54:08:17 > > Searching other bug reports and posts, I've tried: > > hw.bge.allow_asf="0" > hw.pci.enable_msi="0" > > But it didn't help. Any ideas? > > If I don't use the loader.conf settings above, I also get (before the > watchdog timeouts): > > bge0: 2 link states coalesced > bge0: 2 link states coalesced > bge0: 2 link states coalescedThere is a WIP version at the following URL. http://people.freebsd.org/~yongari/bge/if_bge.c http://people.freebsd.org/~yongari/bge/if_bgereg.h http://people.freebsd.org/~yongari/bge/brgphy.c I have a couple of positive feedbacks but it seems it still has some issues. Let me know whether it makes any difference on your box.> > Best regards, > > -- > Anders.
Anders Nordby
2012-Aug-23 16:22 UTC
bge problems in RELENG_9, bge0: watchdog timeout -- resetting
Hi, On ons, jul 04, 2012 at 06:01:36pm -0700, YongHyeon PYUN wrote:> There is a WIP version at the following URL. > http://people.freebsd.org/~yongari/bge/if_bge.c > http://people.freebsd.org/~yongari/bge/if_bgereg.h > http://people.freebsd.org/~yongari/bge/brgphy.c > > I have a couple of positive feedbacks but it seems it still has > some issues. Let me know whether it makes any difference on your > box.I tried these bge source files in 9.1-PRERELEASE this week, and it does not help. If I try to log in with SSH I get: Aug 23 17:30:32 login: ROOT LOGIN (root) ON ttyu0 bge0: watchdog timeout -- resetting Aug 23 17:31:31 kernel: bge0: watchdog timeout -- resetting Aug 23 17:31:31 kernel: bge0: link state changed to DOWN Aug 23 17:31:35 kernel: bge0: link state changed to UP bge0: watchdog timeout -- resetting Aug 23 17:33:24 kernel: bge0: watchdog timeout -- resetting Aug 23 17:33:24 kernel: bge0: link state changed to DOWN Aug 23 17:33:28 kernel: bge0: link state changed to UP I tried setting hw.bge.allow_asf to 0, but it did not help. During boot I get: pcib3: <ACPI PCI-PCI bridge> at device 2.0 on pci0 pci3: <ACPI PCI bus> on pcib3 pci0:3:0:0: failed to read VPD data. bge0: <Broadcom unknown BCM5719, ASIC rev. 0x5719001> mem 0xf6bf0000-0xf6bfffff0xf6be0000-0xf6beffff,0xf6bd0000-0xf6bdffff irq 32 at device 0.0 on pci3 bge0: APE FW version: NCSI v1.0.80.0 bge0: CHIP ID 0x05719001; ASIC REV 0x5719; CHIP REV 0x57190; PCI-E miibus0: <MII bus> on bge0 brgphy0: <BCM5719C 1000BASE-T media interface> PHY 1 on miibus0 brgphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, 1000baseT, 1000baseT-aster, 1000baseT-FDX, 1000baseT-FDX-master, auto, auto-flow bge0: Ethernet address: 2c:76:8a:54:08:14 pci0:3:0:1: failed to read VPD data. bge1: <Broadcom unknown BCM5719, ASIC rev. 0x5719001> mem 0xf6bc0000-0xf6bcffff0xf6bb0000-0xf6bbffff,0xf6ba0000-0xf6baffff irq 36 at device 0.1 on pci3 bge1: APE FW version: NCSI v1.0.80.0 bge1: CHIP ID 0x05719001; ASIC REV 0x5719; CHIP REV 0x57190; PCI-E miibus1: <MII bus> on bge1 brgphy1: <BCM5719C 1000BASE-T media interface> PHY 2 on miibus1 brgphy1: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, 1000baseT, 1000baseT-aster, 1000baseT-FDX, 1000baseT-FDX-master, auto, auto-flow bge1: Ethernet address: 2c:76:8a:54:08:15 pci0:3:0:2: failed to read VPD data. bge2: <Broadcom unknown BCM5719, ASIC rev. 0x5719001> mem 0xf6b90000-0xf6b9ffff0xf6b80000-0xf6b8ffff,0xf6b70000-0xf6b7ffff irq 32 at device 0.2 on pci3 bge2: APE FW version: NCSI v1.0.80.0 bge2: CHIP ID 0x05719001; ASIC REV 0x5719; CHIP REV 0x57190; PCI-E miibus2: <MII bus> on bge2 brgphy2: <BCM5719C 1000BASE-T media interface> PHY 3 on miibus2 brgphy2: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, 1000baseT, 1000baseT-aster, 1000baseT-FDX, 1000baseT-FDX-master, auto, auto-flow bge2: Ethernet address: 2c:76:8a:54:08:16 pci0:3:0:3: failed to read VPD data. bge3: <Broadcom unknown BCM5719, ASIC rev. 0x5719001> mem 0xf6b60000-0xf6b6ffff0xf6b50000-0xf6b5ffff,0xf6b40000-0xf6b4ffff irq 36 at device 0.3 on pci3 bge3: APE FW version: NCSI v1.0.80.0 bge3: CHIP ID 0x05719001; ASIC REV 0x5719; CHIP REV 0x57190; PCI-E miibus3: <MII bus> on bge3 brgphy3: <BCM5719C 1000BASE-T media interface> PHY 4 on miibus3 brgphy3: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, 1000baseT, 1000baseT-aster, 1000baseT-FDX, 1000baseT-FDX-master, auto, auto-flow bge3: Ethernet address: 2c:76:8a:54:08:17 Regards, -- Anders.