CentOS - Jun 2014 - CentOS 6 - Ethernet Bond Errors, 1 per frame

# modinfo ixgbe
filename:
/lib/modules/2.6.32-431.el6.x86_64/kernel/drivers/net/ixgbe/ixgbe.ko
version:        3.15.1-k
license:        GPL
description:    Intel(R) 10 Gigabit PCI Express Network Driver
author:         Intel Corporation, <linux.nics at intel.com>
srcversion:     B390E9D9904338B52C2E361

I have updated this to 3.18.7-1 as well, same results

# ifconfig bond1 |grep error
          RX packets:4476995 errors:6940 dropped:0 overruns:0 frame:6940
          TX packets:2130564 errors:0 dropped:0 overruns:0 carrier:0

# cat /proc/net/bonding/bond1
Ethernet Channel Bonding Driver: v3.6.0 (September 26, 2009)

Bonding Mode: adaptive load balancing
Primary Slave: None
Currently Active Slave: p6p1
MII Status: up
MII Polling Interval (ms): 100
Up Delay (ms): 0
Down Delay (ms): 0

Slave Interface: p6p1
MII Status: up
Speed: 10000 Mbps
Duplex: full
Link Failure Count: 0
Permanent HW addr: 90:e2:ba:1e:12:5c
Slave queue ID: 0

Slave Interface: p6p2
MII Status: up
Speed: 10000 Mbps
Duplex: full
Link Failure Count: 0
Permanent HW addr: 90:e2:ba:1e:12:5d
Slave queue ID: 0

Any suggestions and help are much appreciated!

Thanks!
Nick

Em 17-06-2014 19:54, Nick Niemeyer escreveu:
> # modinfo ixgbe
> filename:
> /lib/modules/2.6.32-431.el6.x86_64/kernel/drivers/net/ixgbe/ixgbe.ko
> version:        3.15.1-k
> license:        GPL
> description:    Intel(R) 10 Gigabit PCI Express Network Driver
> author:         Intel Corporation, <linux.nics at intel.com>
> srcversion:     B390E9D9904338B52C2E361
>
> I have updated this to 3.18.7-1 as well, same results
>
> # ifconfig bond1 |grep error
>            RX packets:4476995 errors:6940 dropped:0 overruns:0 frame:6940
>            TX packets:2130564 errors:0 dropped:0 overruns:0 carrier:0
Frame errors are usually cable error and/or alike but can also be a 
result of mis-communication between driver/NIC firmware. What does 
'ethtool -S' for each slave interface give you?

Marcelo
> # cat /proc/net/bonding/bond1
> Ethernet Channel Bonding Driver: v3.6.0 (September 26, 2009)
>
> Bonding Mode: adaptive load balancing
> Primary Slave: None
> Currently Active Slave: p6p1
> MII Status: up
> MII Polling Interval (ms): 100
> Up Delay (ms): 0
> Down Delay (ms): 0
>
> Slave Interface: p6p1
> MII Status: up
> Speed: 10000 Mbps
> Duplex: full
> Link Failure Count: 0
> Permanent HW addr: 90:e2:ba:1e:12:5c
> Slave queue ID: 0
>
> Slave Interface: p6p2
> MII Status: up
> Speed: 10000 Mbps
> Duplex: full
> Link Failure Count: 0
> Permanent HW addr: 90:e2:ba:1e:12:5d
> Slave queue ID: 0
>
> Any suggestions and help are much appreciated!
>
> Thanks!
> Nick
> _______________________________________________
> CentOS mailing list
> CentOS at centos.org
> http://lists.centos.org/mailman/listinfo/centos
>