search for: hisax

Hi After modprobe hisax type=35 (Billion HFC PCI) on a Xorcom Rapid ISO I get: HISAX Dec 12 16:25:35 localhost kernel: HiSax: Linux Driver for passive ISDN cards Dec 12 16:25:35 localhost kernel: HiSax: Version 3.5 (module) Dec 12 16:25:35 localhost kernel: HiSax: Layer1 Revision 1.1.4.1 Dec 12 16:25:35 localhost kernel...

...silence in both directions. Any idea what could be the cause? Thanks for your help, Gunther Lspci: 0000:01:07.0 Network controller: Tiger Jet Network Inc. Tiger3XX Modem/ISDN interface [I'm not sure what kind of card this is but maybe there's the cathedral of cologne on it(?)] I4l uses hisax type=20 The output is: ISDN subsystem Rev: 1.1.2.3/1.1.2.3/1.1.2.2/1.1.2.3/1.1.2.2/1.1.2.2 loaded HiSax: Linux Driver for passive ISDN cards HiSax: Version 3.5 (module) HiSax: Layer1 Revision 2.46.2.5 HiSax: Layer2 Revision 2.30.2.4 HiSax: TeiMgr Revision 2.20.2.3 HiSax: Layer3 Revision 2.22.2.3 Hi...

The card is an ASUSCOM ISDNLink PCI (passive) and the circuit is from Qwest (in the US). I will be using this circuit only for voice (I'm doing this because of the poor quality of my POTS lines). I've compiled Hisax (as a module) into my 2.4.25 kernel, and with 'modprobe hisax type=35 protocol=4 id=hisax' I get the following: Apr 7 10:34:24 dev kernel: HiSax: Linux Driver for passive ISDN cards Apr 7 10:34:24 dev kernel: HiSax: Version 3.5 (module) Apr 7 10:34:24 dev kernel: HiSax: Layer1 Revision...

...ith kernel 2.4.27, connecting to a Telstra (Australia) Onramp Home Highway ISDN line. I'm pretty certain the card and line both work since they've been used in this machine for PPP before this (but with an older kernel with DoV patches, which are no longer to be used). If I do # modprobe hisax type=11,11 protocol=2,2 id="HiSax" it responds (in the syslog) with: kernel: ISDN subsystem Rev: 1.1.4.1/1.1.4.1/1.1.4.1/1.1.4.1/1.1.4.1/1.1.4.1 loaded kernel: HiSax: Linux Driver for passive ISDN cards kernel: HiSax: Version 3.5 (module) kernel: HiSax: Layer1 Revision 1.1.4.1 kernel: H...

...TS lines. I've been trying to find an inexpensive PCI interface solution to connect this to Asterisk as voice lines. I prefer ISDN BRI over POTS lines because of the improved signalling, fast dialing, clean audio, and so on. I've tried three different Passive ISDN boards supported by the HiSax drivers, with various degrees of failure. None have been able to complete a call. (Linux kernel 2.4.22, with AVM Fritz, DynaFax, and HFC cards) According to the HiSax documentation, NI-1 is a supported protocol.

...):- Asterisk version 0.9.0 running on Linux 2.4.26 I've tried both compiling the NETjet drivers into the kernel, then as modules (as described in the NETjet doco) I've applied the voice patch from Traverse to the NETjet code as documented. When compiled as a module, modprobe hisax type=20 protocol=2 id="HiSax", produces (similar output in log when compiled into kernel):- ISDN subsystem Rev: 1.1.4.1/1.1.4.1/1.1.4.1/1.1.4.1/1.1.4.1/1.1.4.1 loaded HiSax: Linux Driver for passive ISDN cards HiSax: Version 3.5 (module) HiSax: Layer1 Revision 1.1.4.1 HiSax: Layer...

If I want to send outgoing DTMF over a BRI interface, can I do it with 'isdn4linux' or must I use the 'capi' library? -- . . ___. .__ Posix Systems - Sth Africa /| /| / /__ mje@posix.co.za - Mark J Elkins, Cisco CCIE / |/ |ARK \_/ /__ LKINS Tel: +27 12 807 0590 Cell: +27 82 601 0496 -------------- next part -------------- A non-text attachment was

...952 0 (unused) mousedev 4212 1 hid 18596 0 (unused) usbmouse 2008 0 (unused) input 3200 0 [keybdev mousedev hid usbmouse] uhci 24560 0 (unused) usbcore 58144 1 [hid usbmouse uhci] hisax 448228 0 (unused) isdn 115712 0 [hisax] slhc 5040 0 [ppp_generic isdn] isa-pnp 30724 0 [hisax] ide-scsi 8048 0 3c59x 26736 1 is the problem that the hisax isdn drivers have loaded? i...

...der external ISDN modem and mgetty-sendfax is used for sending faxes. I'd like to send the faxes also via the HFC card but I don't have any common interface for it: mISDN doesn't support faxes, CAPI is available for active cards only (I believe - if I'm wrong please correct me) and HiSax plus ISDN4LINUX doesn't work: I tried to load the hisax module parallel to zaphfc but this immediately results in a message "Primary D-Channel on span 1 down" in asterisks log. After a rmmod of hisax and rmmod/modprobe of the zaphfc module asterisk works again. Does anybody have an i...

...I should change from i4l drivers to capi drivers. wiki help seems to be for the Fritz card only...??? I have ticked the suggested boxes in 'menuconfig', explored the capi4linux websites - etc... but am missing some magic. I've "modprobe capi", if I don't "modprobe hisax type=11" to get- HiSax: Card 1 Protocol EDSS1 Id=HiSax (0) HiSax: Eicon.Diehl Diva driver Rev. 1.1.4.2 ... then whet am I meant to do instead? Obviously no *.... (load_module: CAPI not installed!) A pointer in the right direction please? ie - does the Dumb EICON card work with capi?, do I n...

HI: Is there any way to raise up sound volume on fxo on TDM04B without changing tx-gain and rx-gain ? __________________________________________________ Do You Yahoo!? Tired of spam? Yahoo! Mail has the best spam protection around http://mail.yahoo.com

Hi all! I'm new with telephony cards and DAHDI drivers. I have installed Asterisk NOW 3.0.0 and update to Asterisk 11.7.0, modules are update too. I'm following the installation guide of Atcom [1] for AX1600P analogic card, modules are loaded [root at pbx ~]# lsmod | grep -E "hisax|netjet|dahdi" netjet 14618 0 isdnhdlc 4523 1 netjet mISDNipac 33989 1 netjet mISDN_core 73118 3 netjet,mISDNipac hisax 410162 0 isdn 119265 1 hisax dahdi_transcode 5240 1 wctc4xxp dahdi_voic...

...42949386.060000] TE110P: Span configured for CAS/HDB3 [42949386.060000] Calling startup (flags is 4099) [42949386.100000] CSLIP: code copyright 1989 Regents of the University of California [42949386.130000] ISDN subsystem Rev: 1.1.2.3/1.1.2.3/1.1.2.2/1.1.2.3/1.1.2.2/1.1.2.2 loaded [42949386.190000] HiSax: Linux Driver for passive ISDN cards [42949386.190000] HiSax: Version 3.5 (module) [42949386.190000] HiSax: Layer1 Revision 2.46.2.5 [42949386.190000] HiSax: Layer2 Revision 2.30.2.4 [42949386.190000] HiSax: TeiMgr Revision 2.20.2.3 [42949386.190000] HiSax: Layer3 Revision 2.22.2.3 [42949386.190000...

...ies with the card initialization in Debian and isdn4linux. For the single card I was using with "isdntool" for initialization, wich works fine but has no support for two cards. Can anyone tell me exactly how to initialize the ISDN system manually ??? It all starts with "modprobe -v hisax type=21,21" (loading hisax and telling it that we'll use two teles pci cards) and then ? what else ??? Thanks in advance Miguel Gon?alves -----BEGIN PGP SIGNATURE----- Version: PGPfreeware 7.0.3 for non-commercial use <http://www.pgp.com> iQA/AwUBQg30kO+AwW6HpSS6EQLHFgCg19JJkyZ9K...

I am getting quite frustrated today, so please bear with me. I just installed Fedora Core 4 (was running RedHat 9 with a working Asterisk) now my Fedora does not appear to be recognizing my X100P (clone) at all. Hardware browser just shows them as unknown device. driver: hisax So, of course, my zaptel drivers do not work and therefore my asterisk does not work. any help would be greatly appreciated .. Shawn -------------- next part -------------- An HTML attachment was scrubbed... URL: http://lists.digium.com/pipermail/asterisk-users/attachments/20050913/50196116/atta...

...Size Used by Tainted: PF pwcx 87616 1 pwc 38944 1 [pwcx] iptable_nat 12660 1 (autoclean) ip_conntrack 12684 1 (autoclean) [iptable_nat] ip_tables 10432 3 [iptable_nat] ide-scsi 7456 0 hisax 447812 4 isdn 110176 5 [hisax] 3c59x 24648 2 emu10k1 55680 22 sound 52876 0 [emu10k1] ac97_codec 9568 0 [emu10k1] soundcore 3236 7 [emu10k1 sound] usb-uhci 207...

I need HELP pls! BRISTUFF: Bad Sound quality CAPI : PTP Mode dont supported mISDN : kernel is 2.4.x and not 2.6.x HISAX : PTMP ok, PTP incoming ok but in outgoing asterisk dont compose number(i listen dial tone and than i can compose number via dtmf) Asterisk CLI (g3 is group of Modem[i4l]/ttyI0 and ttyI1): Called g3: 3453444444 (Channel is used but dont compose...

Hello all. I have an ISDN passive card (HC HFC 2BDS0) using HiSAX driver (since this is a passive card, I can't use the CAPI driver... ). "All" I want is recieve faxes and store them on diferent folders depending the destination number. So far I was able to do a similar thing with voice (vbox), but what I really pretend is recieving faxes. My sy...

Hi There I am running SuSE Linux 9.3 and installed Asterisk from the RPM's. I have a Diva ISDN card, making use of the HiSAX drivers. Configuration seems to be OK. I can receive a call coming in on the ISDN and route it to a SIP (softphone) on my PC. As soon as I hangup the call, then asterisk stops working. I am forced to kill the process with -9, a normal kill does not work. The last message on the Asterisk console w...

Hi I was using asterisk 1.0.7 until now. For my connection with the PSTN I used a good old isa hisax teles 16.3 isdn card. Now while compiling 1.2 I nothiced that i4l and chan_modem is no longer supported? Is there any way of getting my good old ISA card to work under 1.2? The docs keep saying use misdn, capi, etc from now on. But I don't think my card is CAPI capable arne -------------- next...