asterisk users - Nov 2006 - Definity Asterisk Caller ID Issue

You should run the 4ESS protocol ("a" on the Definity command
"change DS1 board#) as the Definity may not send Display Name for the NI-2
protocol (settings "b" or "d")

Remember to make the Asterisk zapata settings consistent with the Definity.

On the Definity trunk group form Page 1, change "Codeset to send
Display" to "0 (zero)", also make sure Outgoing Display is
"y" . On Page 2, make sure Send Name and Send Calling Number are
"y".

Setting Send UCID = "n" as well as Send Codeset 6/7LAI =
"n", will clean up those Unknown IEs.

The Zaptel software only supports CodeSet 0 Information Elements so the Display
Name has to be  in Codeset 0.

Mark
> > 
> !! < Unknown IE 1544 (len = 6)
> 
> !! Unknown IE 8 (cs6, Unknown Information Element)
> 
> Progress Description: Calling equipment is non-ISDN
> 
> TON: International Number
> 
> 
> 
> 
> 
> xxx*CLI>
> 
> < [ 02 01 d4 d2 08 02 0a e6 05 04 03 90 90 a2 18 03 a1 83 8b 1e 
> 02 81 83
> 70 05 91 34 33 38 39 96 08 04 d0 35 30 80 ]
> 
-------------- next part --------------
An HTML attachment was scrubbed...
URL:
http://lists.digium.com/pipermail/asterisk-users/attachments/20061105/5892e752/attachment.htm

isdn-pri/line-side, protocol b, and a I think were using a TN464 card on the
definity. I'll have to check on the card. We are using pri_net singnaling
and national is our switchtype in asterisk. I'll try the changes and report
back. Thank you so much!

-CP

________________________________________
From: asterisk-users-bounces@lists.digium.com
[mailto:asterisk-users-bounces@lists.digium.com] On Behalf Of
mavince@optonline.net
Sent: Sunday, November 05, 2006 6:09 PM
To: asterisk-users@lists.digium.com
Subject: [asterisk-users] Definity Asterisk Caller ID Issue

You should run the 4ESS protocol ("a" on the Definity command
"change DS1 board#) as the Definity may not send Display Name for the NI-2
protocol (settings "b" or "d")
?
Remember to?make the Asterisk zapata settings consistent with the Definity.
?
On the Definity trunk group form Page 1, change "Codeset to send
Display" to "0 (zero)", also make sure Outgoing Display is
"y" . On Page 2, make sure Send Name and Send Calling Number are
"y".
?
Setting Send UCID = "n" as well as Send Codeset 6/7LAI =
"n", will clean up those Unknown IEs.
?
The Zaptel software only supports CodeSet 0 Information Elements so the Display
Name has to be? in Codeset 0.
?
Mark
> > 
> !! < Unknown IE 1544 (len = 6)
> 
> !! Unknown IE 8 (cs6, Unknown Information Element)
> 
> Progress Description: Calling equipment is non-ISDN
> 
> TON: International Number
> 
> 
> 
> 
> 
> xxx*CLI>
> 
> < [ 02 01 d4 d2 08 02 0a e6 05 04 03 90 90 a2 18 03 a1 83 8b 1e 
> 02 81 83
> 70 05 91 34 33 38 39 96 08 04 d0 35 30 80 ]
>