similar to: Trouble installing TE405P with asterisk@home

Hi to all, I have a problem with this wildcard and one E1 line. The server is a Asus P4P800S with the 865PE chipset, and 512MB RAM. The kernel version is 2.4.26. I have donwload and build the latest CVS version of zaptel, libpri and asterisk following the ufficial instructions of digium. I have set up my server in this way: zaptel.conf loadzone=it defaultzone=it

I'm installing TE405P card. This is my zaptel.conf. -------------------------------------- span=1,0,0,ccs,hdb3,crc4 span=2,1,0,ccs,hdb3,crc4 span=3,0,0,ccs,hdb3,crc4 span=4,0,0,ccs,hdb3,crc4 loadzone = us defaultzone= us -------------------------------------- When i modprobe wct4xxp, -------------------------------------- PCI: Found IRQ 11 for device 02:0b.0 PCI: Sharing IRQ 11 with

Hi I got the 2nd Gen firmware upgraded on the TE405P. I recompiled after putting in the upgraded board but did not change any conf, but the spans become active but will not come up. I guess I am missing something or are the any changes to the zaptel/libpri software that is required. I cannot find any info about this or does this new firmware only work with latest CVS. I am using 1.0.9 with

Forget the sound card. It isn't related. The subject above should have read 'TE405P No Voice Problem' or something similar. It appears to be a zaptel timing issue, but I have found a workaround. For those of you just tuning in, here is the story: I have a CentOS/Intel 865 box currently running Asterisk 1.2.7.1 and zap 1.2.5, both compiled from the source available off the main

Anyone care to elaborate on the differences between the T400P and the TE405P? -Darren -------------- next part -------------- An HTML attachment was scrubbed... URL: http://lists.digium.com/pipermail/asterisk-users/attachments/20050908/e817f8bb/attachment.htm

http://www.mixdown.ca/~asterisk/ The card seems to be working fine. Don't expect warranty on it though. :-) Why? Because I wanted a quad-span T1 card which worked in the high-end systems I was intending it for, but that I could also keep a few in stock and if the system mainboard failed, pull the card an put it in a standard PC system. I didn't want to have to stock 3.3V and 5V

Hi Everybody, Is there anyone who already uses Asterisk with TE405P card? Is this card going well with the old E400P or T400P drivers? Are there a lot of differences? In the card's data sheet writes this sentece: "Digium has designed the TE405P to be fully compatible with existing software applications..." Is this meaning the the old drivers are also OK for this card? Thank you

I understand from the archives that * does this occassionally, but I'm trying to figure out why. * didn't do this at all for two days, and then it's gone and done it 3 times in the past hour. It does not seem to be affecting calls, I'm just curious as to the reasoning behind the B channel resets and why they are so erratic. Regards, Andrew

I have TE405P span connected to a patton/digi 2977 T1/PRI port. Zaptel starts up fine without any errors. Libpri is installed as well. But I get the following when trying to load asterisk ------- Jul 3 19:30:26 ERROR[8192]: Signalling requested is PRI Signalling but line is in Unknown signalling 896 signalling Jul 3 19:30:26 ERROR[8192]: Unable to register channel '25-48' Jul

Hi, I havn't E1 board from Digium but I would like to know which is the used IC (chip) for PCI HDLC communication? Best Regards, Miroslav Nachev

Is there anything to choose, in performance, between a TE405P and a TE410P? I understand the difference between the PCI bus voltages, and certainly don't intend to try Andrew's hacksaw operation :-). But if I choose the card first, and a compatible mobo second, does it make any difference which? Cheers Tony -- Tony Mountifield Work: tony@softins.co.uk - http://www.softins.co.uk Play:

Does anyone know which physical interrupt line out of the four on the PCI backplane the TE405P uses? Or is it somehow configurable by hardware or software? I'm trying to diagnose a problem where the card generates no interrupts in one system, but is fine in another system. These systems are SBC-in-backplane type. My knowledge of how PCI works at the physical layer is rather limited, but I

Can anybody tell me the difference between a TE410P and a TE405P? Is it JUST the 5v vs 3.3v pcis slot spec, or is there some thing else? </edg>

Hi, I've got an * box with 4 E1 (TE405P) and a Class 4 Cirpack switch (www.cirpack.com). <IP Network>--<*>--<Cirpack>--<Public PSTN Network> ISDN interco is EuroIsdn, ports are configured ccs, hdb3, crc4. Cirpack is Network, * is Terminal/User. As I encountered some pb with Sip to Zap transcoding (* to Cirpack way poor quality, the other way fine), I tryed to

Can anyone with a TE405P tell me what zttool tells them the type of card installed. With ours it says it's a TE410P. B

Hi, I've got an * box with 4 E1 (TE405P) and a Class 4 Cirpack switch (www.cirpack.com). <IP Network>--<*>-[TE405P]-<Cirpack>-<Public PSTN Network> ISDN interco is EuroIsdn, ports are configured ccs, hdb3, crc4. Cirpack is Network, * is Terminal/User. As I encountered some pb with Sip to Zap transcoding (* to Cirpack way poor quality, the other way fine), I

Hello, I would like to know if FreeBSD has drivers for TE405P cards submitted to the ports. I have acquired a card and would really like to use it with FreeBSD. The wiki said the drivers havent been tested yet. Have there been any updates since then? regards Kavit _______________________________________________ Asterisk-Dev mailing list Asterisk-Dev@lists.digium.com

On March 16, 2005 05:57 am, Andrew Kohlsmith wrote: > Can you put this card in a totally separate machine with your slackware HDD > just to see if it comes up properly in another machine? This is very > unusual. > -A Unfortunately I have already also tried this, without results. I do not know what to do any more..

I have a channel bank (TA750) and a PRI with 30 channels connected to a TE405P, in the channel bank I have a extension to a fax machine, but it doesn't work to send or receive fax. There are any advice ? Kind regards, Miguel

I would appreciate if people that have experience with stable Asterisk and TE405P cards installations on Xeon servers can share what kind of motherboards and chipset are using. I'm trying to configure a new Asterisk server with one TE405P on an Intel board with Xeon 3.0Ghz but not all Intel boards and chipsets works fine with these Digium boards. Thanks for your help ! Alfred Certain