search for: mgcp

I'm trying to use a 4 port ATA that was designed for use with MGCP 1.0 / NCS 1.0 -- is the channel_mgcp compat with NCS -- anything I can do to make it compat?? This is what happens - below *CLI> mgcp reload Reloading MGCP == Parsing '/etc/asterisk/mgcp.conf': Found Use EXIT or QUIT to exit the asterisk console == MGCP Listening on 10.1.22.39:242...

Hi, in following of a recent discussion I got to work on MGCP with the Cisco ATA186 again, and got it to work very nicely. However, there is a little thing with transfers I would like to get comments on: Call comes in from PSTN and goes to an ATA186 (MGCP) Call is answered and then, using flash, transferred to another extension If the extension is availabl...

Hello, I have just received an MGCP Phone for test purpose and I can't place a call from my MGCP Phone. I can call my MGCP phone from a SIP Phone. Here is my mgcp.conf: ; ; MGCP Configuration for Asterisk ; [general] ;port = 2427 ;bindaddr = 0.0.0.0 ;[dlinkgw] ;host = 192.168.0.64 ;context = default ;line => aaln/2 ;line =&g...

...e, and only a long and then small beep. When I try to dial digits I hear again those long+short beeps, but the extension dialed is not ringing. If I pres flash again I get back to the previous caller. On the console I see those digits that I dial after pressing flash. What is wrong? here is my mgcp.conf and exept from the console about this call. mgcp.conf: [dg104s] host = 172.50.0.1 threewaycalling = yes transfer = yes callwaiting = yes cancallforward=yes callreturn=yes context = test callgroup = 3 pickupgroup = 3 console: -- Executing Dial("MGCP/aaln/3@dg104s-1", "MGCP...

I've got a ShoreTel 210 MGCP phone drops calls. My packet capture indicates that the phone may be trying to renew its registration with *, but reports Restart Method of Disconnected (frame 2), then * seems to take that as a sign that it has lost the connection and closes things down. The phone, meanwhile, seems to think it c...

Hello all, I'm looking for some help to try to understand why my CPE doesn't work good with Asterisk in MGCP. Here is what I want to do : - Register a TECOM AH4021 on Asterisk in MGCP with the following profile in mgcp.Conf : [general] port = 2727 bindaddr = 10.95.20.1 disallow=all allow=g729 allow=alaw 020202020202] context=mgcp host=dynamic canreinvite=no dtmfmode=rfc2833 nat=yes threewaycalling=yes...

I've been trying to figure this one out for a while, but to no avail. I have my cisco ubr924 setup for MGCP with Asterisk as the call-agent. I have manually registered the endpoint in mgcp.conf. When I pick up the phone, I get no dialtone and debug shows errors. IOS on the ubr924 is 12.2. Any help is appreciated. from mgcp.conf: [ubr924] host=65.37.86.203 context = from-sip (just as a test context...

Hi. I'm new in Asterisk with MGCP. I set up a MGCP user agent and start asterisk with the next configuration files. '--------------- extensions.conf ---------------------------------------------------- [general] static=yes writeprotect=yes [globals] ap1 => mgcp/aaln/ap200@64.76.148.186 [macro-apl1] exten => s,1,Dial($...

I'm trying to link up Cisco MGCP-enabled router (residential gateway) with Asterisk, and it looks like some sort of protocol mismatch, could it be MGCP 0.1 vs 1.0? Look at this (x.x.x.99 is the router, x.x.x.98 is Asterisk): MGCP read: NTFY 2 aaln/0@voip-gw1 MGCP 0.1 X: 0 O: hd from 192.168.154.99:2427MGCP read: NTFY 2 aaln/0@...

see below I tried to call 98013356 from the following phone (from mgcp.conf) [iptlf03] host = 192.168.33.3 context = default inbanddtmf = 1 callerid = 22545062 line => aaln/1 Console output: == Spawn extension (capiring, 9988001133335566, 1) exited non-zero on 'MGCP/aaln/1@iptlf03-1' -- MGCP mgcp_hangup(MGCP/aaln/1@iptlf03-1) on aaln/1@iptlf03...

Hi all, i am using CVS-HEAD-08/13/04-12:00:00-BRI-stuffed-0.1.0-RC4a with Cisco ATA-186 3.1.1 atamgcp We are used to make an special ;) blind transfer like (Flash)Number(Hangup before anyone answers or ring). Then * crashes (see below) if the man in the middle is an cisco-ata-186-mgcp If one waits until the last one rings, then hangup, everything is fine. If one waits until the last one answers...

Hi, I picked up a router with 8 voice ports that supports MGCP, but it has several options that I am not familiar with or do not seem apparent in the mgcp.conf. Enter the default IP address for the Notified Entity: [0.0.0.0] Enter the listening port of the Notified Entity: [2427] Enter the IP address for MGCP signalling (Data): [192.168.0.210] Enter the local...

Can anyone tell me what MGCP error that I'm getting means? The hardware is a MRP200 in a Cisco 7750 PBX. (Its a FXO blade with 2 slots, first one has a 4 port FXO card and the second has 2 port FXO card. It recognises those correctly, at least to the point of this error.) MGCP Debugging Enabled MGCP read: NTFY 13 aal...

Hello List, I'm trying to setup MGCP channel with a Centile Media Hub box. My Centile box has 4 ports and I got no dial tone. Can somebody help with this isuue? This is my mgcp.conf and extensions.conf Thanks Daniel. ; MGCP Configuration for Asterisk ; [general] port = 2427 bindaddr = 192.168.11.20 disallow=all allow=g729 allow=alaw...

I know this is not the most appropriated list to this, but I will try: Does anyone know what is the criteria to the generation of the transaction identifiers in MGCP? I mean, are they generated by a randomic method? I'm using Asterisk and MGCP eyeP Phone and observed that the RSIP and NTFY (methods created by the gateway) use high values in the transaction identifiers, while the RQNT, AUEP, CRCX and DLCX (by the call agent) use low values for it. I hope I...

I strange error messages when using mgcp and ata186 . This session is simply dial into 600 demo extension - echo test ... Handling request 'NTFY' on aaln/1@10.0.1.19 Transmitting: 200 29 OK to 10.0.1.19:2427 -- Endpoint 'aaln/1@10.0.1.19-1' observed '0' -- MGCP Asked to indicate tone: on aaln/1@10....

Hey guys, can you shead some light on this? I will copy my mgcp.conf and post below, but here is the problem. I can't get call waiting to work with my MGCP device. I already have one call going, and I can hear the second call come in, I flash over to it, but all I get is a dial tone, * puts the 1st call on mute/hold, but I never get the second, and it ter...

Hello folks, I'm trying to get an 8x8 DTA-310 running mgcp to work. I get no dialtone & can't get it to ring. My mgcp.conf says: ; ; MGCP Configuration for Asterisk ; [general] port = 2427 bindaddr = 0.0.0.0 [172.16.2.25] host = 172.16.2.25 context = default line => aaln/1 And here's the interesting bits of extensions.conf: [globals] ....

Hello I have a problem with my MGCP voice gateway. I use D-Link DG104S Boot PROM Version 3.0B38-D Firmware Version 3.0T86-D I tried asterisk v 0.7.2 and I am using latest CVS version now. When I dial a number very fast, or when I use a redial function, my asterisk receives coupled digits. My co-worker called number 245005111, the...

hi all I'm being spammed by these messages in the console (see below) and sound doesn't work with today's cvs. I rolled back a week, and it works fine. In addition to the sound problems, I had to enable inband dtmf squelch on the dilnk mgcp phones. if not, each pressed key was counted twice NOTICE[245776]: File chan_mgcp.c, Line 710 (mgcp_rtp_read): MGCP ast_dsp_process NOTICE[245776]: File chan_mgcp.c, Line 710 (mgcp_rtp_read): MGCP ast_dsp_process NOTICE[245776]: File chan_mgcp.c, Line 710 (mgcp_rtp_read): MGCP ast_dsp_process...