Nut upsuser - Mar 2007 - UPSilon 2000 via USB linux

Hi everybody, I am installing an Upsilon 2000 UPS via USB adapter on a RedHat 9
and I cant make that the device communicate correctly. Please any help will be
welcome

dmesg attached
Thanks 
Gonzalo
 
Red Hat 9.0 2.4.34.1

#dmesg
usb.c: registered new driver usbdevfs
usb.c: registered new driver hub
usb.c: new USB bus registered, assigned bus number 1
usb-uhci.c: $Revision: 1.275 $ time 15:28:15 Mar 19 2007
usb-uhci.c: High bandwidth mode enabled
usb-uhci.c: USB UHCI at I/O 0xe400, IRQ 11
usb-uhci.c: Detected 2 ports
usb.c: new USB bus registered, assigned bus number 2
usb-uhci.c: USB UHCI at I/O 0xe800, IRQ 10
usb-uhci.c: Detected 2 ports
usb.c: new USB bus registered, assigned bus number 3
usb-uhci.c: USB UHCI at I/O 0xec00, IRQ 10
usb-uhci.c: Detected 2 ports
usb.c: new USB bus registered, assigned bus number 4
usb-uhci.c: v1.275:USB Universal Host Controller Interface driver
usb.c: registered new driver hid
usb.c: USB device 2 (vend/prod 0x67b/0x2303) is not claimed by any active
driver.
usb.c: registered new driver serial
usbserial.c: USB Serial support registered for Generic
usbserial.c: USB Serial Driver core v1.4
usbserial.c: USB Serial support registered for PL-2303
usbserial.c: PL-2303 converter detected
usbserial.c: PL-2303 converter now attached to ttyUSB0 (or usb/tts/0 for devfs)
 		
---------------------------------
 Pregunt?. Respond?. Descubr?.
 Todo lo que quer?as saber, y lo que ni imaginabas,
 est? en Yahoo! Respuestas (Beta).
 Probalo ya! 
-------------- next part --------------
An HTML attachment was scrubbed...
URL:
http://lists.alioth.debian.org/pipermail/nut-upsuser/attachments/20070326/145595be/attachment.html

On 3/26/07, gonzalo campuris <gcampuris@yahoo.com.ar>
wrote:
> Hi everybody, I am installing an Upsilon 2000 UPS via USB adapter on a
> RedHat 9 and I cant make that the device communicate correctly. Please any
> help will be welcome
Can you please send some of your configuration files and error
messages? This will help narrow down the problem.

-- 
- Charles Lepple

On 3/26/07, gonzalo campuris <gcampuris@yahoo.com.ar>
wrote:
> # /etc/upsilon/upsilon start
> Initial Config Complete
> <UPSilon>
> Copyright(C) 1998 Mega System Technologies, Inc.
> Ver. 2.1
> Start Running!
> #
>  UPS Adapter No Response!!, type [upsilon stop] to stop this process
> # /etc/upsilon/upsilon stop
> # Daemon Process Stops!
This list is for the Network UPS Tools (NUT) software, but this log
looks like it is from something else entirely.

The RPMs listed on rpmfind.net for RH9 seem very old, so you will
probably need to compile from source:

http://www.networkupstools.org/source.html

Then, since your UPS is not listed in the compatibility list, you
probably need to try a few drivers, such as megatec. There is a new
gamatronic driver that is being expanded to handle the full SEC
protocol, and that might work as well. It looks like the port is
/dev/ttyUSB0.

-- 
- Charles Lepple