----- Original Message -----
> From: "Noah Engelberth" <Noah at directlinkcomputers.com>
> To: "Asterisk Users Mailing List - Non-Commercial Discussion"
> <asterisk-users at lists.digium.com>
> Sent: Tuesday, July 3, 2012 10:56:10 AM
> Subject: [asterisk-users] IAX trunking stopped working
> I administer a group of Asterisk servers running a mix of 10.3, 10.4,
> and 1.8.8.1 (mostly 10.4). One of those servers is a call
> concentrator/relay for E911 service. All of the other servers make
> an IAX connection to the relay server, which then hands off to a SIP
> trunk to my E911 provider. It all worked as recently as 2 weeks ago,
> but I discovered that sometime between then and now it stopped
> working without any explanation. Last modified time on the config
> files is over 2 months ago.
> The setup is as follows:
> On the call relay (IAX ?receiver?)
> [my-remote-server]
> type=user
> host=dynamic
> username=my-remote-username
> encryption=yes
> secret=my-remote-secret
> context=my-call-context
> deny=0.0.0.0/0.0.0.0
> permit=remote.server.ip.address/255.255.255.255
> On the VoIP servers (IAX ?sender?)
> - One of the servers is set to register: register =>
> my-remote-username:my-remote-secret at call.relay.server.ip
> - Another is set to just use the peer definition as below without
> trying to register
> [my-remote-server]
> type=peer
> host=call.relay.server.ip
> username=my-remote-username
> secret=my-remote-secret
> qualify=no
> Dialplan on the VoIP servers:
> exten => 911,1,Verbose()
> same => n,Dial(IAX2/my-remote-server/911)
> Dialplan on the relay server:
> [my-call-context]
> exten => 911,1,Verbose()
> same => n,Dial(Relay to E911)
> The issue I?m seeing is this:
> - On the servers that are set to register, the relay server is
> rejecting the registration (I?ve confirmed the
> username/peername/secrets are an exact match on both sides, and
> nothing has changed from when they were working). IAX debug on the
> relay server shows the auths come in and the relay server send
> REGREJ ? Registration Refused, Cause Code 29. IAX debug on the
> server attempting to register shows sending the REGAUTH packets and
> receiving the REGREJ packets. The IP address shown in the IAX debug
> packets matches the IP address in the permit rule for each peer
> that?s supposed to register.
Can you set authdebug and iaxdebug to true in your iax2 configuration -
preferably
on both ends, but in particular on the server that is servicing the registration
attempt - and post the portion of the DEBUG logs that shows it rejecting the
registration?
Something is failing authentication, and authdebug should tell us at least
why the server thinks it should reject the attempt.
> - On the server that is set to just send the calls, an attempt to
> dial 911 just hangs for 60 seconds and eventually times out without
> sending the call. IAX debug on the relay server shows the call start
> frame get RX?d, shows the relay server try to TX a CTOKEN frame, and
> nothing further (other than retransmissions of the call start
> frame). IAX debug on the server trying to send the call to the relay
> server shows the TX for the call start frame, but no RX for the
> CTOKEN frames.
Is this the same server that failed to register? If so, it may be best
to focus on that problem first.
> Ultimately, this has gone from working to totally broken without any
> apparent change to my configuration. I need help to try to
> troubleshoot it further, I?ve tried everything I can think of
> (including transferring the backed-up working config files to a
> brand new clean-load server, upgrading Asterisk, and recreating the
> configurations by hand), and nothing seems to be helping.
Since you have a number of different servers running different versions
of Asterisk, can you provide which server in your scenario is running
which version?
> Thank you,
> Noah Engelberth
> MetaLINK Technologies
--
Matthew Jordan
Digium, Inc. | Software Developer
445 Jan Davis Drive NW - Huntsville, AL 35806 - USA
Check us out at: http://digium.com & http://asterisk.org