asterisk users - Apr 2007 - BeroNet HFC-4S card is now detected as only 2 ports

Hello list,

After upgrading from BRIstuff 1y-b to 1y-e my ISDN card is suddently
detected as 2 ports instead of 4.

I still load the driver as "modprobe qozap ports=12" as I've
always
done. But now it only sees 2 ports.
Output of "lspci -vvv"
------ cut --------
02:01.0 ISDN controller: Cologne Chip Designs GmbH ISDN network
Controller [HFC-4S] (rev 01)
        Subsystem: Cologne Chip Designs GmbH Unknown device b560
        Control: I/O+ Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR- FastB2B-
        Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
        Interrupt: pin A routed to IRQ 22
        Region 0: I/O ports at ddb8 [size=8]
        Region 1: Memory at fcefa000 (32-bit, non-prefetchable) [size=4K]
        Capabilities: [40] Power Management version 2
                Flags: PMEClk- DSI+ D1+ D2+ AuxCurrent=0mA
PME(D0+,D1+,D2+,D3hot+,D3cold-)
                Status: D0 PME-Enable- DSel=0 DScale=0 PME-
------ cut --------

Anyone has any ideas?

-- 
Best regards,

Henrik Woffinden

On Fri, Apr 06, 2007 at 01:18:24AM +0200, Henrik Woffinden
wrote:
> Hello list,
> 
> After upgrading from BRIstuff 1y-b to 1y-e my ISDN card is suddently
> detected as 2 ports instead of 4.
> 
> I still load the driver as "modprobe qozap ports=12" as I've
always
> done. But now it only sees 2 ports.
> Output of "lspci -vvv"
> ------ cut --------
> 02:01.0 ISDN controller: Cologne Chip Designs GmbH ISDN network
> Controller [HFC-4S] (rev 01)
>         Subsystem: Cologne Chip Designs GmbH Unknown device b560
>         Control: I/O+ Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop-
> ParErr- Stepping- SERR- FastB2B-
>         Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
> <TAbort- <MAbort- >SERR- <PERR-
>         Interrupt: pin A routed to IRQ 22
>         Region 0: I/O ports at ddb8 [size=8]
>         Region 1: Memory at fcefa000 (32-bit, non-prefetchable) [size=4K]
>         Capabilities: [40] Power Management version 2
>                 Flags: PMEClk- DSI+ D1+ D2+ AuxCurrent=0mA
> PME(D0+,D1+,D2+,D3hot+,D3cold-)
>                 Status: D0 PME-Enable- DSel=0 DScale=0 PME-
> ------ cut --------
Just a comment: the CHANGES file has the item "fixed detection of
miniPCI cards (qozap)". Take a look at the diff between qozap/qozap.c
in -d and in -e .

-- 
               Tzafrir Cohen       
icq#16849755                    jabber:tzafrir@jabber.org
+972-50-7952406           mailto:tzafrir.cohen@xorcom.com       
http://www.xorcom.com  iax:guest@local.xorcom.com/tzafrir