similar to: BeroNet HFC-4S card is now detected as only 2 ports

Hi everyone. We have a problem here... Hope somebody can give us some hints. We have a HP ProLiant DL180 G6 Server with a Debian/Lenny sytem. Asterisk 1.4.21.2 (1.4.21.2~dfsg-3+lenny1) with zaptel (1.4.11) and libpri (1.4.3) is installed. There is a QuadBRI-Card installed: # lspci -vv -s 06:04.0 06:04.0 ISDN controller: Cologne Chip Designs GmbH ISDN network Controller [HFC-4S] (rev 01)

Hello, I am having problems, getting my asterisk-domU to work properly. It consists of the following components: - Debian Etch under Xen-3.1 with a 2.6.18-kernel - Asterisk 1.2.24 - mISDN-1.1.5 I have 2 HFC-ISDN-cards, which I pass through to the Asterisk-DomU in permissive mode. This is working fine. The strange problem is, that the two HFC-ISDN-cards are not beeing initialized by the

Hi! I tried to pcipassthrough usb-controllers to domu to use it with a memory-stick. First xen complained that the driver needs write-access to its configuration space, so I added these to pci-quirks. Since it still didn''t work I also added the device to pci-permissive but I still get an errormessage with Oops (at the end of this email) when sticking in the memory-stick. I tried

Hi! I tried to pcipassthrough usb-controllers to domu to use it with a memory-stick. First xen complained that the driver needs write-access to its configuration space, so I added these to pci-quirks. Since it still didn''t work I also added the device to pci-permissive but I still get an errormessage with Oops (at the end of this email) when sticking in the memory-stick. I tried

Hi List, I'm setting up a system with one TDM400P (2*FXO + 2 * FXS) and one Junghanns QuadBRI on a Fedora Core 6 (Kernel 2.6.20-1.2944.fc6). I'm using the bristuff-0.3.0-PRE-1y-e kit. It download zaptel-1.2.16, libpri-1.2.4 and asterisk-1.2.17 When it's the time for ztcfg to do its job it complains with <ZT_SPANCONFIG failed on span 2: No such device or address (6)>

PC: HP Vetra VL400 Mainbood: Intel815 BIOS: Phonix 4.0 release 6.0 OS: REDHAT 9.0 I installed the X100P in PCI slot 2 and disable the USB port, serial-port and parallel-port in BIOS. I can't found the X100P card in " cat interrupts" But I can found the card in the "cat ioports" use "lspci" I found the X100Pcard use the interrupts 11 too. Who can help me to solve

Hi All, I hope I'm posting this to the appriopriate list, and that cross posting to two lists is OK. (If not, I'm sure I'll hear about it quickly :)) I'm running Asterisk on my (new) VIA EPIA-V motherboard. This seems to be the ideal platform for a home version of asterisk - its small, quiet, low power, and should have plenty of computing horsepower if only it would work!

Hi, we've purchased new Beronet Octobri card and have problems loading modules for stock Asterisk for Debian Sarge (it has bristuff patches in it). when loading qozap it says that no multibri card was found although lspci shows it... There were quite some rumours about bristuff not liking other than junghanns cards, but don't know if something happened.... Anyone recently used this

I have a new laptop (Dell 9400) that I am trying to work with Xen 3.0. Xen works fine, runs windows XP under HVM. But, the Xen kernel on Dom0 has a few problems with some of the hardware. The network card is a Broadcom 4400 10/100BaseT. Normally loading the b44 module gives this: Apr 28 20:07:53 ipanema kernel: [4294683.185000] b44.c:v0.97 (Nov 30, 2005) Apr 28 20:07:53 ipanema kernel:

I came into an Abit AX8 motherboard and single core AMD Athlon 64 FX. I did a quick install of CentOS 5.0 on it to make sure everything worked and then returned the hard disk and case to the original owner. After getting a new case and hard disk, I downloaded the CentOS 5.1 cd images and installed. For some reason the motherboard's on board sound no longer works (worked with CentOS

Hi. I'm trying to get a Beronet QuadBRI card work with bristuff drivers. Though qozap module loads right, all card spans are in deactivated status. I'm quite sure my configuration is correct and using a single BRI card instead of the quadBRI the status is active and I can place and receive calls. On Beronet installation manual I read that Beronet and Junghanns cards are identical in

Hi list, Is Digium Wildcard B410P compatible with Asterisk 1.2 / 1.4 (zaptel of course) directly out of the box, or do I need things like bristuff? http://www.digium.com/en/products/hardware/b410p.php Best regards, Henrik Woffinden

I mistakenly only replied to Yijing Wang the first time. Here are the further details. uname -a: Linux p5-133 3.15.2-p5-133 #1 Thu Jun 26 22:56:27 EDT 2014 i586 GNU/Linux Here is the output from lspci -vvvxxx: root at p5-133:~# cat lspci.txt 00:00.0 Host bridge: Intel Corporation 430FX - 82437FX TSC [Triton I] (rev 01) Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-

I have a few oqo2 units that I use for testing, normally using the dongle for ethernet connection. Well supposedly they have atheros wifi. in dmseg I see: ath5k 0000:03:04.0: PCI INT A -> GSI 17 (level, low) -> IRQ 17 ath5k 0000:03:04.0: registered as 'phy0' ath5k phy0: Couldn't identify radio revision. ath5k 0000:03:04.0: PCI INT A disabled I press magic <fnc-?> per

*RESEND* due to exceeding the mailinglists limit for attachment size. Hi, I''m trying to get secondary vga-passthrough on a HVM guest to work with a AMD HD6570 and the native kernel radeon driver and kernel modesetting. So the guest still gets the emulated stdvga or cirrus device(used in my case here) as primary/boot vga adapter. - When i don''t passthrough the radeon card, the

Yijing, cat /sys/bus/pci/devices/0000\:00\:0e.0/msi_bus returns 1, suggesting that it supports MSI. However, this "00:0e.0 PCI bridge: PLX Technology, Inc. PEX8112 x1 Lane PCI Express-to-PCI Bridge (rev aa)" is a component of the addin card. Wouldn't the lack of support for MSI by the chipset "00:00.0 Host bridge: Intel Corporation 430FX - 82437FX TSC [Triton I] (rev 01)"

Hi, we are trying to install Junghann's quadBRI into Dell PowerEdge 2800 system without success. I don't know if the issue can be that Junghann's card fits 32-bit slot and Dell PE 2800 has only 3 PCI-X 64-bit slots. Can this be an issue? We get "CRC errors for HDLC frame" when the card is initialized. Any idea what can be wrong? 1/ We use latest bristuff packages. 2/

Hello list, I'm having a problem with a BRI card, a B200E (PCI-e) card on an Intel server with a riser that I'm guessing is what's making the problem. The output of lspci -vvv is: 07:00.0 ISDN controller: Cologne Chip Designs GmbH ISDN network Controller [HFC-4S] (rev 01) Subsystem: Cologne Chip Designs GmbH Device e884 Control: I/O+ Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop-

I have this cheap "ENCORE 10/100Mbps Fast Ethernet PCI Adapter" which comes with its own driver that compiles to 'sundance.ko' and performs bad (30% packet loss) on a fully updated CentOS 4.4 box. This brand, model and driver have worked OK for me on some other CentOS installations, none of which are 4.4. Short of replacing the board, which you can bet I will do, can anybody

hello, Here (http://updates.xorcom.com/astribank/bristuff/1.4/INSTALL.html) you can read : cd qozap modprobe zaptel insmod qozap.o (for kernel 2.4) insmod qozap.ko (for kernel 2.6) ztcfg I thought modprobe was a replacement for insmod. Can someone be kind enough to explain : 1. the difference between modprobe and insmod, 2. why should both commands be issued, 3. how modprobe and insmod compare