Vidura Senadeera
2007-Mar-07 22:56 UTC
[asterisk-users] Re: Back to back E1 - asterisk <=> toshiba pbx - Call droping
Hi steve and All, I'm attaching cat proc/interrupts out put, lspci -bv out put, zapa.conf, zaptel.conf for your information Thanks so much for the feedback and I do accordingly. Hope to get rid off this isue any how. To day also reported 10 call drops within 2 hours of period. fook forward to have your support on this regard. Thanks & Regards, Vidura Senadeera, Network Engineer, Debug Solutions Sri Lanka. Tel - +94114520036 Mobile - +94777766596 Web - www.debug.lk Message: 16> Date: Wed, 7 Mar 2007 05:05:36 -0500 > From: "Steve Totaro" <stotaro@asteriskhelpdesk.com> > Subject: RE: [asterisk-users] Back to back E1 - asterisk <=> toshiba > pbx - Calldroping issue > To: "Asterisk Users Mailing List - Non-Commercial Discussion" > <asterisk-users@lists.digium.com> > Message-ID: > < > DFB93BD730105941BD1A782A1EE9E95CCC76@1-0fa9e300af524.asteriskhelpdesk.com> > > Content-Type: text/plain; charset="us-ascii" > > As these problems are very time sensitive and frustrating, I suggest you > document each change you make and do them one at a time so you can > actually know what the problem was and not introduce new problems in the > process. > > > > Find someone who is on the phone quite a bit and will give you an honest > evaluation of the call dropping situation (unless you yourself are > experiencing this issue too). Some people are so quick to say, "It is > still happening" without starting the evaluation from a clean slate > after each change. > > > > You may want to check your Asterisk log for more insight. > /var/log/asterisk/full. Also you can turn on debugging on one span at a > time and see if you can find something there > > > > Do you have a resetinterval set in zapata.conf? If you can isolate the > dropped calls to the reset interval (watch the console, it will scroll > with each channel being reset) then set resetinterval=never. If there > is no entry for resetinterval, add it and set it to never since it is > defaulted to on. > > > > Also, try changing your second span timing from span=2,2,0,ccs,hdb3,crc4 > to span=2,0,0,ccs,hdb3,crc4. This in combination with your first span > should accept timing from the Telco and then supply it to your Toshiba, > I would actually try this first. > > > > Another thought, It seems you have quite a lot of hardware in that box. > I am not sure how much is too much, but that would probably just rear > it's ugly head as poor audio. > > Thanks, > Steve Totaro > http://www.asteriskhelpdesk.com > > > _____ > > From: asterisk-users-bounces@lists.digium.com > [mailto:asterisk-users-bounces@lists.digium.com] On Behalf Of Vidura > Senadeera > Sent: Wednesday, March 07, 2007 2:15 AM > To: support@digium.com > Cc: asterisk-users@lists.digium.com > Subject: [asterisk-users] Back to back E1 - asterisk <=> toshiba pbx - > Calldroping issue > > > > > > Hi Team, > > > > I have integrated asterisk with Toshiba analog PBX. NOw the live setup > is going. > > > > Now I am facing call droping problem. It's happening ample time. 10-20 > calls are droping every day. > > > > What could be the reason. I attached latest zapata.conf file for your > information. > > > > > > > > This is being a huge issue. > > > > Highly appreciate your help on this regard. > > > Thanks & Regards, > > Vidura Senadeera. > > > > > On 1/26/07, Vidura Senadeera <vidurased@gmail.com > wrote: > > Dear Marco, > > > > There is a huge problem i'm facing. > > > > My asterisk server included with TDM2451E and 2 TE110p cards. One E1 i > conected to the telco. other E1 port i'm using to cros-connection with > toshiba pbx. My telco E1 d channels communicating well. but toshiba pbx > E1 not getting. d-channels are not getting up. > > what could be the issue. i'm using asterisk -1.2.14 and zaptel 1.2.12. > > > > notes - if i put, zap show channels in asterisk cli. its only showing > the first 31 channels. but with ztcfg -vvv it showing al the channels. > > > > my configs are > > > > # Span 1: WCT1/0 "Digium Wildcard TE110P T1/E1 Card 0" HDB3/CCS/CRC4 RED > > # ============ Suntel E1 connection =========> > span=1,1,0,ccs,hdb3,crc4 > bchan=1-15,17-31 > dchan=16 > > # Span 2: WCT1/1 "Digium Wildcard TE110P T1/E1 Card 1" > # ============ Legacy PBX E1 connection ======> > span=2,2,0,ccs,hdb3,crc4 > bchan=32-46,48-62 > dchan=47 > > # Span 3: WCTDM/0 "Wildcard TDM2400P Prototype Board 1" > fxoks=63 > fxoks=64 > fxoks=65 > fxoks=66 > fxoks=67 > fxoks=68 > fxoks=69 > fxoks=70 > fxoks=71 > fxoks=72 > fxoks=73 > fxoks=74 > fxoks=75 > fxoks=76 > fxoks=77 > fxoks=78 > fxoks=79 > fxoks=80 > fxoks=81 > fxoks=82 > fxsks=83 > fxsks=84 > fxsks=85 > fxsks=86 > > # Global data > > loadzone = us > defaultzone = us > > Regards, > > vidura > > > > > > -- > Thanks & Regards, > Vidura B. Senadeera. > > > > > -- > Thanks & Regards, > Vidura B. Senadeera. > > > > > -- > Thanks & Regards, > Vidura B. Senadeera. > > -------------- next part -------------- > An HTML attachment was scrubbed... > URL: > http://lists.digium.com/pipermail/asterisk-users/attachments/20070307/62a82c69/attachment-0001.htm > > ------------------------------ > > Message: 17 > Date: Wed, 7 Mar 2007 11:17:07 +0100 > From: "Thomas Deillon" <Thomas.Deillon@smart-telecom.ch> > Subject: [asterisk-users] Asterisk 1.4.1 - Calling problem > To: "Asterisk Users Mailing List - Non-Commercial Discussion" > <asterisk-users@lists.digium.com> > Message-ID: > < > 86918CDC1242004D8B0563A43D1E2F0C027E2D09@exch-pul-01.interne.smart-telecom.ch > > > > Content-Type: text/plain; charset="us-ascii" > > Hi all, > > > > I install the Asterisk 1.4.1 in order to use the T.38 pass-through, but > for the moment, I cannot even make call .... > > I have this WARNING: > > > > [Mar 7 11:32:09] WARNING[13395]: chan_sip.c:12290 handle_response: > Remote host can't match request BYE to call > '5759b80c119e1d51679dc66b519c6eac@194.148.41.50'. Giving up. > > > > Do you know what is this error and what can I do to solve it ? > > > > Thanks a lot for your help, > > > > Thomas > > > > -------------- next part -------------- > An HTML attachment was scrubbed... > URL: > http://lists.digium.com/pipermail/asterisk-users/attachments/20070307/6740a4e6/attachment.htm > > ------------------------------ > > _______________________________________________ > --Bandwidth and Colocation provided by Easynews.com -- > > asterisk-users mailing list > To UNSUBSCRIBE or update options visit: > http://lists.digium.com/mailman/listinfo/asterisk-users > > > End of asterisk-users Digest, Vol 32, Issue 22 > ********************************************** >-- Thanks & Regards, Vidura B. Senadeera. -------------- next part -------------- An HTML attachment was scrubbed... URL: http://lists.digium.com/pipermail/asterisk-users/attachments/20070307/fd3226b5/attachment.htm
Vidura Senadeera
2007-Mar-07 23:01 UTC
[asterisk-users] Fwd: Back to back E1 - asterisk <=> toshiba pbx - Call droping
Skipped content of type multipart/alternative-------------- next part
--------------
A non-text attachment was scrubbed...
Name: zaptel.conf
Type: application/octet-stream
Size: 766 bytes
Desc: not available
Url :
http://lists.digium.com/pipermail/asterisk-users/attachments/20070307/72df5acc/zaptel.obj
-------------- next part --------------
CPU0 CPU1
0: 327803993 339534993 IO-APIC-edge timer
8: 0 2 IO-APIC-edge rtc
9: 0 0 IO-APIC-level acpi
14: 491341 509003 IO-APIC-edge ide0
169: 326692201 340097503 IO-APIC-level wcte11xp
193: 467454 449006 IO-APIC-level aacraid
201: 40446355 59 IO-APIC-level eth0
209: 263442740 403340853 IO-APIC-level wcte11xp
217: 404363696 262780720 IO-APIC-level wctdm24xxp
NMI: 0 0
LOC: 667384291 667384290
ERR: 0
MIS: 0
-------------- next part --------------
00:00.0 Host bridge: Intel Corporation E7320 Memory Controller Hub (rev 0c)
Subsystem: Intel Corporation E7320 Memory Controller Hub
Flags: bus master, fast devsel, latency 0
Capabilities: [40] Vendor Specific Information
00:02.0 PCI bridge: Intel Corporation E7525/E7520/E7320 PCI Express Port A (rev
0c) (prog-if 00 [Normal decode])
Flags: bus master, fast devsel, latency 0
Bus: primary=00, secondary=01, subordinate=01, sec-latency=0
Capabilities: [50] Power Management version 2
Capabilities: [58] Message Signalled Interrupts: 64bit- Queue=0/1 Enable-
Capabilities: [64] Express Root Port (Slot-) IRQ 0
00:03.0 PCI bridge: Intel Corporation E7525/E7520/E7320 PCI Express Port A1 (rev
0c) (prog-if 00 [Normal decode])
Flags: bus master, fast devsel, latency 0
Bus: primary=00, secondary=02, subordinate=02, sec-latency=0
Capabilities: [50] Power Management version 2
Capabilities: [58] Message Signalled Interrupts: 64bit- Queue=0/1 Enable-
Capabilities: [64] Express Root Port (Slot-) IRQ 0
00:1c.0 PCI bridge: Intel Corporation 6300ESB 64-bit PCI-X Bridge (rev 02)
(prog-if 00 [Normal decode])
Flags: bus master, 66Mhz, fast devsel, latency 48
Bus: primary=00, secondary=03, subordinate=03, sec-latency=48
I/O behind bridge: 00002000-00002fff
Memory behind bridge: d8100000-d81fffff
Prefetchable memory behind bridge: 00000000dc000000-00000000dff00000
Capabilities: [50] PCI-X bridge device.
00:1e.0 PCI bridge: Intel Corporation 82801 PCI Bridge (rev 0a) (prog-if 00
[Normal decode])
Flags: bus master, fast devsel, latency 0
Bus: primary=00, secondary=04, subordinate=04, sec-latency=32
I/O behind bridge: 00003000-00003fff
Memory behind bridge: d8200000-d9ffffff
00:1f.0 ISA bridge: Intel Corporation 6300ESB LPC Interface Controller (rev 02)
Flags: bus master, medium devsel, latency 0
00:1f.1 IDE interface: Intel Corporation 6300ESB PATA Storage Controller (rev
02) (prog-if 8a [Master SecP PriP])
Subsystem: Hewlett-Packard Company: Unknown device 25a1
Flags: bus master, medium devsel, latency 0
I/O ports at <unassigned>
I/O ports at <unassigned>
I/O ports at <unassigned>
I/O ports at <unassigned>
I/O ports at 1400
Memory at 40000000 (32-bit, non-prefetchable)
00:1f.3 SMBus: Intel Corporation 6300ESB SMBus Controller (rev 02)
Subsystem: Hewlett-Packard Company: Unknown device 25a1
Flags: medium devsel
I/O ports at 1100
03:01.0 RAID bus controller: Adaptec AAC-RAID (rev 01)
Subsystem: Adaptec 2120S (Crusader)
Flags: bus master, 66Mhz, slow devsel, latency 32, IRQ 9
Memory at dc000000 (32-bit, prefetchable)
Capabilities: [80] Power Management version 2
03:02.0 Ethernet controller: Broadcom Corporation NetXtreme BCM5782 Gigabit
Ethernet (rev 03)
Subsystem: Hewlett-Packard Company: Unknown device 000c
Flags: bus master, 66Mhz, medium devsel, latency 32, IRQ 9
Memory at 00000000d8100000 (64-bit, non-prefetchable)
Capabilities: [48] Power Management version 2
Capabilities: [50] Vital Product Data
Capabilities: [58] Message Signalled Interrupts: 64bit+ Queue=0/3 Enable-
03:03.0 Network controller: Tiger Jet Network Inc. Tiger3XX Modem/ISDN interface
Subsystem: Unknown device 79fe:0001
Flags: bus master, medium devsel, latency 32, IRQ 9
I/O ports at 2000
Memory at d8110000 (32-bit, non-prefetchable)
Capabilities: [40] Power Management version 2
03:04.0 Ethernet controller: Digium, Inc. Wildcard TDM2400P (rev 11)
Subsystem: Digium, Inc. Wildcard TDM2400P
Flags: bus master, medium devsel, latency 32, IRQ 9
I/O ports at 2400
Memory at d8111000 (32-bit, non-prefetchable)
Capabilities: [c0] Power Management version 2
04:01.0 Network controller: Tiger Jet Network Inc. Tiger3XX Modem/ISDN interface
Subsystem: Unknown device 79fe:0001
Flags: bus master, medium devsel, latency 32, IRQ 10
I/O ports at 3000
Memory at d8200000 (32-bit, non-prefetchable)
Capabilities: [40] Power Management version 2
04:04.0 VGA compatible controller: ATI Technologies Inc Rage XL (rev 27)
(prog-if 00 [VGA])
Subsystem: ATI Technologies Inc Rage XL
Flags: bus master, stepping, medium devsel, latency 66, IRQ 10
Memory at d9000000 (32-bit, non-prefetchable)
I/O ports at 3400
Memory at d8201000 (32-bit, non-prefetchable)
Capabilities: [5c] Power Management version 2
-------------- next part --------------
;
; Zapata telephony interface
;
; Configuration file
[trunkgroups]
;trunkgroup=>2,16
;spanmap=1,2,1
;trunkgroup=>3,47
;spanmap=2,3,1
[channels]
;==========Suntel E1 PRI configuration ===========
signalling=pri_cpe ; pri_cpe = PRI slave ; pri_net = PRI master
switchtype=euroisdn
echocancel=yes ; You can set this to 32, 64, or 128, tweak to your needs.
echocancelwhenbridged=yes
echotraining=400 ; Asterisk trains to the beginning of the call, number is in
milliseconds
resetinterval=never
callerid=asreceived
usecallerid=yes
overlapdial=no
pridialplan=unknown
pritimer => t203,30000
immediate=no
busycount=5
rxgain=3
txgain=0
endcalleridafter=5
rxwink=300
callprogress=yes
busydetect=no
useincomingcalleridonzaptransfer=yes
loadzone=us
context=from-pstn ; Points to the default context of your extensions.conf
group=2
pickupgroup=0,1,2,3
channel=>1-15
channel=>17-31
;channel=>17-19
;==========================================
;PRI/E1 link
;=========== Connection to Legacy PBX ============
signalling=pri_net;pri_cpe = PRI slave ; pri_net = PRI master
switchtype=euroisdn
echocancel=yes ; You can set this to 32, 64, or 128, tweak to your needs.
echocancelwhenbridged=yes
echotraining=400 ; Asterisk trains to the beginning of the call, number is in
milliseconds
rxgain=1
txgain=0
endcalleridafter=5
rxwink=300
resetinterval=never
callerid=asreceived
;amaflags=default
usecallerid=yes ; newly added
callwaiting=no
callprogress=yes
transfer=yes
canpark=yes
cancallforward=yes
busydetect=no
busycount=5
pridialplan=unknown
pritimer => t203,30000
overlapdial=yes
threewaycalling=yes
immediate=no
usecallinpres=yes
callgroup=3
pickupgroup=0,1,2,3
loadzone=us
context=from-internal
group=3
channel=>32-46,48-62
;=========================
language=en
context=from-pstn
signalling=fxs_ks
rxwink=300 ; Atlas seems to use long (250ms) winks
;
; Whether or not to do distinctive ring detection on FXO lines
;
usedistinctiveringdetection=yes
busydetect=yes
usecallerid=yes
hidecallerid=no
callwaiting=yes
usecallingpres=yes
callwaitingcallerid=yes
callprogress=yes
threewaycalling=yes
transfer=yes
cancallforward=yes
callreturn=yes
echocancel=yes
echocancelwhenbridged=no
echotraining=800
rxgain=0.9
txgain=0.9
group=0
group=1
callgroup=1
pickupgroup=0,1,2,3
immediate=no
;Include genzaptelconf configs
#include zapata-auto.conf
;Include AMP configs
#include zapata_additional.conf
Maybe Matching Threads
- Fwd: Back to back E1 - asterisk <=> toshiba pbx -Call droping
- Back to back E1 - asterisk <=> toshiba pbx - Calldroping issue
- Re: Back to back E1 - asterisk <=> toshiba pbx - Call droping issue [ ref:00D36mPe.50032wycQ:ref ]
- Back to back E1 - asterisk <=> toshiba pbx - Call droping issue
- Re: busy/hangup/answer detection in PRI E1 channels (Vidura Senadeera)