asterisk users - Aug 2005 - Asterisk 1.0.9: TE411P replacement for TE410P 1stgen causes crashes

Hi all,

I replaced a TE410P Rev C 1st Generation Firmware with a TE411P
without any cfg changes (zaptel/zapata).

As a result Asterisk crashes on outbound from PRI4 going to PRI1 calls:

Aug 23 18:22:00 WARNING[4693]: chan_zap.c:7545 zt_pri_error: PRI: !! Got a 
UA, but i'm in state 1
Aug 23 18:22:00 WARNING[4693]: chan_zap.c:7545 zt_pri_error: PRI: !! Got a 
UA, but i'm in state 1

Urgent handler
Urgent handler
-- Accepting overlap voice call from '4123655105' to '555115' on
channel
0/26, span 4
-- Starting simple switch on 'Zap/119-1'
Urgent handler
Urgent handler
Ouch ... error while writing audio data: : Broken pipe
Junk at the beginning 49443303
Warning, flexibel rate not heavily tested!
Segmentation fault

Are there any changes to the config neccessary?
Are there known issues with this Asterisk version?
Can I temporarily disable the TE411 specific stuff to get asterisk running 
again?

Platform: HP DL380G3 with 2x2.4Ghz, 1GB RAM, 1xTE411P,1xOctoBRI
Version: Asterisk 1.0.9-BRIstuffed-0.2.0-RC8n 

zaptel.conf:
span=1,1,0,ccs,hdb3,crc4
span=2,0,0,ccs,hdb3,crc4
span=3,0,0,ccs,hdb3,crc4
span=4,0,0,ccs,hdb3,crc4

zapata.conf:
[channels]

switchtype=euroisdn
pridialplan=local
prilocaldialplan=local
priindication=outofband
internationalprefix=00
nationalprefix=0
usecallingpres=yes
hidecallerid=no
busydetect=no   ; not need on pri
callprogress=no ; was yes but wiki says experimatley could be produce 
hangups
callwaitingcallerid=yes  ; show callerid on callwaitingcalls
echotraining=no
echocancel=yes
echocancelwhenbridged=no
overlapdial=yes
immediate=no
callerid=asreceived
language=de
rxgain=0.0
txgain=0.0

group=1
signalling=pri_cpe
context=pri1
;channel => 25-39,41-55 
channel => 1-15,17-31

group=2
signalling=pri_cpe
context=pri2
channel =>32-46,48-62

group=3
signalling=pri_net
context=pri3
channel => 63-77,79-93

group=4
signalling=pri_net
context=pri4
channel => 94-108,110-124

--
TIA,
Bruno at ic3s dot de

On Tue, Aug 23, 2005 at 08:03:42PM +0200, Bruno.Voigt@ic3s.de
wrote:
> I replaced a TE410P Rev C 1st Generation Firmware with a TE411P
> without any cfg changes (zaptel/zapata).
> 
> As a result Asterisk crashes on outbound from PRI4 going to PRI1 calls:
> 
> Aug 23 18:22:00 WARNING[4693]: chan_zap.c:7545 zt_pri_error: PRI: !! Got a 
> UA, but i'm in state 1
> Aug 23 18:22:00 WARNING[4693]: chan_zap.c:7545 zt_pri_error: PRI: !! Got a 
> UA, but i'm in state 1
> 
> Urgent handler
> Urgent handler
> -- Accepting overlap voice call from '4123655105' to
'555115' on channel
> 0/26, span 4
> -- Starting simple switch on 'Zap/119-1'
> Urgent handler
> Urgent handler
> Ouch ... error while writing audio data: : Broken pipe
> Junk at the beginning 49443303
> Warning, flexibel rate not heavily tested!
> Segmentation fault
> 
> Are there any changes to the config neccessary?
There shouldn't be.
> Are there known issues with this Asterisk version?
Yes.  You should update your libpri/zaptel/asterisk to the latest CVS-STABLE
release.  This last week we commited quite a few random fixes for the TE411P
that could have affected this particular issue.  If not, it might be quicker
handled if you contact digium support.

-- 
Matthew Fredrickson