dear all, i am looking to enable CALLERID on an Asterisk system comprising a X101P FXO interface connecting to BT PSTN in the uk seems this is supported by the interface but there seems to be varying information on how to enable it in zapata.conf 1. usecallerid=uk 2. ukcallerid=yes being two of the configuration statements offered TIA GT
Graham Turner [ipcomp1@gotadsl.co.uk] wrote:> dear all, i am looking to enable CALLERID on an Asterisk system > comprising a X101P FXO interface connecting to BT PSTN in the uk > > seems this is supported by the interface but there seems to be varying > information on how to enable it in zapata.conf > > 1. usecallerid=uk > > 2. ukcallerid=yes > > being two of the configuration statements offered >The current method is "usecallerid = uk". Of course, you need to patch Zaptel and Asterisk first. The "ukcallerid = yes" was used in an earlier version of the patch. -- _/ _/ _/_/_/_/ _/ _/ _/_/_/ _/ _/ _/_/_/ _/_/ _/ _/ _/ _/_/ _/ K e v i n W a l s h _/ _/ _/ _/ _/ _/ _/ _/_/ kevin@cursor.biz _/ _/ _/_/_/_/ _/ _/_/_/ _/ _/
Kevin, thanks for post reply . i have installed asterisk / zaptel from cvs distribution as of 17/09/04 so i assume this does it have configured zapata.conf as per instruction but i would have expected to have seen the callerid on the asterisk console as it receives the call but then may be not ?? the relevant my extensions.conf is ; exten => s,1,answer exten => s,2,Dial(SIP/1001|10) it is quite possible that callerid is being seen by * but i would have expected it to have been echoed to the console or at least written to the CDR entries ??? would you have any suggestions as to how to confirm this going a bit further on, the whole point of this exercise is to allow this CALLERID to be displayed on the console of a SIP peer (7940 ip phone) that is defined as an asterisk extension thanks 4 yr help GT ----- Original Message ----- From: "Kevin Walsh" <kevin@cursor.biz> To: "Asterisk Users Mailing List - Non-Commercial Discussion" <asterisk-users@lists.digium.com> Sent: Sunday, September 19, 2004 1:48 PM Subject: RE: [Asterisk-Users] uk caller id> Graham Turner [ipcomp1@gotadsl.co.uk] wrote: > > dear all, i am looking to enable CALLERID on an Asterisk system > > comprising a X101P FXO interface connecting to BT PSTN in the uk > > > > seems this is supported by the interface but there seems to be varying > > information on how to enable it in zapata.conf > > > > 1. usecallerid=uk > > > > 2. ukcallerid=yes > > > > being two of the configuration statements offered > > > The current method is "usecallerid = uk". Of course, you need to > patch Zaptel and Asterisk first. The "ukcallerid = yes" was used in > an earlier version of the patch. > > -- > _/ _/ _/_/_/_/ _/ _/ _/_/_/ _/ _/ > _/_/_/ _/_/ _/ _/ _/ _/_/ _/ K e v i n W a l s h > _/ _/ _/ _/ _/ _/ _/ _/_/ kevin@cursor.biz > _/ _/ _/_/_/_/ _/ _/_/_/ _/ _/ > > _______________________________________________ > Asterisk-Users mailing list > Asterisk-Users@lists.digium.com > http://lists.digium.com/mailman/listinfo/asterisk-users > To UNSUBSCRIBE or update options visit: > http://lists.digium.com/mailman/listinfo/asterisk-users >
Hi I have my new TDM400P installed and working. I'm running from cvs HEAD with a 2.6.12 kernel on debian. I can't seem to get Caller id working (in uk with clid supplied and working to line) but am a bit unclear on the docs and hence assume it is something I am doing wrong. I would really* appreciate if anyone could take a look below at my zapata.conf and see is there anything incorrect. I am least convinced on the usecallerid=uk option, but if set to 'yes' i get Jul 22 15:38:47 ERROR[19569]: callerid.c:266 callerid_feed: fsk_serie made mylen < 0 (-20) Jul 22 15:38:47 WARNING[19569]: chan_zap.c:5796 ss_thread: CallerID feed failed: Success Jul 22 15:38:47 WARNING[19569]: chan_zap.c:5840 ss_thread: CallerID returned with error on channel 'Zap/2-1' :: zapata.conf :: [channels] context=default switchtype=national signalling=fxo_ls rxwink=300 ; Atlas seems to use long (250ms) winks usecallerid=uk callerid=asreceived cidsignalling=v23 cidstart=usehist callwaiting=yes usecallingpres=yes callwaitingcallerid=yes threewaycalling=yes transfer=yes canpark=yes cancallforward=yes callreturn=yes echocancel=yes echocancelwhenbridged=yes group=1 callgroup=1 pickupgroup=1 immediate=no progzone=uk musiconhold=default ; incoming channels signalling=fxs_ks group=2 context=incoming channel => 1-2 ; outgoing channels signalling=fxo_ks group=1 context=outgoing channel => 3 Thanks loads Chris -------------- next part -------------- An HTML attachment was scrubbed... URL: http://lists.digium.com/pipermail/asterisk-users/attachments/20050722/00e4bca4/attachment.htm