Ok so to be clear about what I need to have setup:
Asterisk side: Configure T1 card like this (it's the 2nd T1 card I have in
the system).
span=2,1,0,esf,b8zs,yellow
fxsls=25-48
Use FXO signalling in my zapata.conf
[channel-bank]
signalling=fxo_ls
context=cb-in
group=2
channel=> 25-48
Adit 600 side:
-Setting slot a.
set a:1 up
set a:1 fdl none
set a:1 lbo 1
set a:1 framing esf
set a:1 id "T1 to Asterisk"
set a:1 linecode b8zs
set a:1 loopdetect on
set a:1:1-24 side drop
set a:1:1-24 type voice
set a:1:1-24 signal ls
-Setting slot 1.
set 1:1-8 signal ls
set 1:1-8 txgain -3
set 1:1-8 rxgain -6
set 1:1-8 impedance 19
-Setting slot 2.
set 2:1-8 signal ls
set 2:1-8 txgain -3
set 2:1-8 rxgain -6
set 2:1-8 impedance 19
-Setting slot 3.
set 3:1-8 signal ls
set 3:1-8 txgain -3
set 3:1-8 rxgain -6
set 3:1-8 impedance 19
On Mon, 2004-06-28 at 22:12, Andrew Kohlsmith wrote:> On Monday 28 June 2004 23:04, Joshua McClintock wrote:
> > Hello, I have an Adit 600 (3 FXS cards) hooked up to a digium T1 card
in
my> > asterisk box. I 'connected' the slots to the a:1 T1
interfaces via the
> > command line. The slots (3 fxs) are configured with 'ls'
signaling. I
> > configured the T1 card with the same line settings as the T1
interfaces
on> > the adit and I get green lights on both the T1 card and the T1
interface
on> > the adit (so they seem to be happy at that link level). I configured
the> > T1 interface in the asterisk box to do 'fxsls' signaling on
all 24
> > channels.
>
> First things first: FXS ports use FXO signalling.
>
> > 1. Should I be getting dial tone on my punch down block yet? I can
tell
> > the handset it getting power when I touch it to the correct places on
the> > punch down block, but no dial tone. Does asterisk need to be aware of
> > these channels before dial tone will be heard?
>
> You won't get dialtone until Asterisk properly configured and running;
it's> what generates the dialtone.
>
> > 2. Did I configure the digium card correctly? Does it need to be
setup
as> > fxo on the asterisk side and fxs on the channel bank side?
>
> No, it is set up as FXS, but remember that FXS ports use FXO signalling.
>
> out of curiousity, why did you choose an Adit600+T1 card for three FXS
ports?> The TDM400P works great for FXS.
3 slots means 24 ports. 3 cards x 8 ports per card.
BTW, when you get asterisk happy and the signalling correct, for
looopstart or kewlstart, all the properly configured port indicators
will turn green and turn yellow/orange on pick up. If in groundstart
mode they will stay off and turn green upon connection.
--
Steven Critchfield <critch@basesys.com>