thr3ads.net - Xen users - [Xen-users] NIC bonding

If this information is useful, please help other people find it:
Share via:

Smithies, Russell

2011-Feb-16 19:47 UTC

[Xen-users] NIC bonding - missing eth0?

I have nic bonding (mode=802.3ad) setup on 2 servers, both running Centos 5.5
In the "Active Aggregator Info", on one reports 4 ports - which is
correct - but the other only reports 3 ports.
It''s always eth0 that shows a different aggregator ID. Changing the
cables around so it hits a different port on the switch makes no difference. The
switch is correctly configured for the port channel.
The only difference between the 2 servers is one is running Xen
(kernel-xen-2.6.18-194.32.1.el5.centos.plus) so I have the usual virtual
interfaces and bridges.

Any ideas what might be happening?
Is something that needs to be "fixed" or is it not really a problem?

Thanx,

Russell Smithies

-------------------------------------------------------------------------------------

[root@invmhp01 ~]# cat /proc/net/bonding/bond0
Ethernet Channel Bonding Driver: v3.4.0 (October 7, 2008)

Bonding Mode: IEEE 802.3ad Dynamic link aggregation
Transmit Hash Policy: layer2 (0)
MII Status: up
MII Polling Interval (ms): 100
Up Delay (ms): 0
Down Delay (ms): 0

802.3ad info
LACP rate: slow
Active Aggregator Info:
        Aggregator ID: 19
        Number of ports: 3 <<<<<<<<
        Actor Key: 17
        Partner Key: 5
        Partner Mac Address: 00:1b:90:3d:90:c0

Slave Interface: eth0
MII Status: up
Link Failure Count: 0
Permanent HW addr: 1c:c1:de:74:97:5c
Aggregator ID: 18

Slave Interface: eth1
MII Status: up
Link Failure Count: 0
Permanent HW addr: 1c:c1:de:74:97:5d
Aggregator ID: 19

Slave Interface: eth2
MII Status: up
Link Failure Count: 0
Permanent HW addr: 1c:c1:de:74:97:5e
Aggregator ID: 19

Slave Interface: eth3
MII Status: up
Link Failure Count: 0
Permanent HW addr: 1c:c1:de:74:97:5f
Aggregator ID: 19

[root@invmhp01 ~]# ifconfig
bond0     Link encap:Ethernet  HWaddr 1C:C1:DE:74:97:5C
          inet addr:147.158.130.183  Bcast:147.158.131.255  Mask:255.255.252.0
          inet6 addr: fe80::1ec1:deff:fe74:975c/64 Scope:Link
          UP BROADCAST RUNNING MASTER MULTICAST  MTU:1500  Metric:1
          RX packets:64087 errors:0 dropped:0 overruns:0 frame:0
          TX packets:18179 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:0
          RX bytes:8293500 (7.9 MiB)  TX bytes:31362799 (29.9 MiB)

eth0      Link encap:Ethernet  HWaddr 1C:C1:DE:74:97:5C
          UP BROADCAST RUNNING SLAVE MULTICAST  MTU:1500  Metric:1
          RX packets:5770 errors:0 dropped:0 overruns:0 frame:0
          TX packets:21 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:0
          RX bytes:410102 (400.4 KiB)  TX bytes:2524 (2.4 KiB)

eth1      Link encap:Ethernet  HWaddr 1C:C1:DE:74:97:5C
          UP BROADCAST RUNNING SLAVE MULTICAST  MTU:1500  Metric:1
          RX packets:22247 errors:0 dropped:0 overruns:0 frame:0
          TX packets:17436 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:1000
          RX bytes:1424685 (1.3 MiB)  TX bytes:31161969 (29.7 MiB)
          Interrupt:239

eth2      Link encap:Ethernet  HWaddr 1C:C1:DE:74:97:5C
          UP BROADCAST RUNNING SLAVE MULTICAST  MTU:1500  Metric:1
          RX packets:6223 errors:0 dropped:0 overruns:0 frame:0
          TX packets:189 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:1000
          RX bytes:442326 (431.9 KiB)  TX bytes:19993 (19.5 KiB)
          Interrupt:235

eth3      Link encap:Ethernet  HWaddr 1C:C1:DE:74:97:5C
          UP BROADCAST RUNNING SLAVE MULTICAST  MTU:1500  Metric:1
          RX packets:29852 errors:0 dropped:0 overruns:0 frame:0
          TX packets:537 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:1000
          RX bytes:6016657 (5.7 MiB)  TX bytes:179281 (175.0 KiB)
          Interrupt:231

lo        Link encap:Local Loopback
          inet addr:127.0.0.1  Mask:255.0.0.0
          inet6 addr: ::1/128 Scope:Host
          UP LOOPBACK RUNNING  MTU:16436  Metric:1
          RX packets:26818 errors:0 dropped:0 overruns:0 frame:0
          TX packets:26818 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:0
          RX bytes:38558929 (36.7 MiB)  TX bytes:38558929 (36.7 MiB)

peth0     Link encap:Ethernet  HWaddr FE:FF:FF:FF:FF:FF
          inet6 addr: fe80::fcff:ffff:feff:ffff/64 Scope:Link
          UP BROADCAST RUNNING NOARP  MTU:1500  Metric:1
          RX packets:41498 errors:0 dropped:0 overruns:0 frame:0
          TX packets:251 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:1000
          RX bytes:3000012 (2.8 MiB)  TX bytes:59877 (58.4 KiB)
          Interrupt:243

vif0.0    Link encap:Ethernet  HWaddr FE:FF:FF:FF:FF:FF
          inet6 addr: fe80::fcff:ffff:feff:ffff/64 Scope:Link
          UP BROADCAST RUNNING NOARP  MTU:1500  Metric:1
          RX packets:127 errors:0 dropped:0 overruns:0 frame:0
          TX packets:39354 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:0
          RX bytes:15520 (15.1 KiB)  TX bytes:2817598 (2.6 MiB)

virbr0    Link encap:Ethernet  HWaddr 00:00:00:00:00:00
          inet addr:192.168.122.1  Bcast:192.168.122.255  Mask:255.255.255.0
          inet6 addr: fe80::200:ff:fe00:0/64 Scope:Link
          UP BROADCAST RUNNING MULTICAST  MTU:1500  Metric:1
          RX packets:0 errors:0 dropped:0 overruns:0 frame:0
          TX packets:42 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:0
          RX bytes:0 (0.0 b)  TX bytes:8160 (7.9 KiB)

xenbr0    Link encap:Ethernet  HWaddr FE:FF:FF:FF:FF:FF
          UP BROADCAST RUNNING NOARP  MTU:1500  Metric:1
          RX packets:38746 errors:0 dropped:0 overruns:0 frame:0
          TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:0
          RX bytes:2217067 (2.1 MiB)  TX bytes:0 (0.0 b)



======================================================================Attention:
The information contained in this message and/or attachments
from AgResearch Limited is intended only for the persons or entities
to which it is addressed and may contain confidential and/or privileged
material. Any review, retransmission, dissemination or other use of, or
taking of any action in reliance upon, this information by persons or
entities other than the intended recipients is prohibited by AgResearch
Limited. If you have received this message in error, please notify the
sender immediately.
======================================================================

_______________________________________________
Xen-users mailing list
Xen-users@lists.xensource.com
http://lists.xensource.com/xen-users

Fajar A. Nugraha

2011-Feb-16 21:42 UTC

head link

Re: [Xen-users] NIC bonding - missing eth0?

On Thu, Feb 17, 2011 at 2:47 AM, Smithies, Russell
<Russell.Smithies@agresearch.co.nz> wrote:> It’s always eth0 that shows a different aggregator ID. Changing the cables
> around so it hits a different port on the switch makes no difference. The
> switch is correctly configured for the port channel.
>
> The only difference between the 2 servers is one is running Xen
> (kernel-xen-2.6.18-194.32.1.el5.centos.plus) so I have the usual virtual
> interfaces and bridges.
>
>
>
> Any ideas what might be happening?
>
> Is something that needs to be “fixed” or is it not really a problem?
> eth0      Link encap:Ethernet  HWaddr 1C:C1:DE:74:97:5C
> peth0     Link encap:Ethernet  HWaddr FE:FF:FF:FF:FF:FF
The presence of "peth0" shows you still use the default
xend''s
network-bridge script. Comment it out from /etc/xen/xend-config.sxp,
and create bridges manually on top of your bonding using OS config
files (/etc/sysconfig/network-scripts/ifcfg-br*). There''s a recent
example on this list (with vlans on top of bonding) from Donny Brooks,
search the archive if you need it.

-- 
Fajar

_______________________________________________
Xen-users mailing list
Xen-users@lists.xensource.com
http://lists.xensource.com/xen-users

Donny Brooks

2011-Feb-16 21:47 UTC

head link

Re: [Xen-users] NIC bonding - missing eth0?

On 2/16/2011 3:42 PM, Fajar A. Nugraha wrote:> On Thu, Feb 17, 2011 at 2:47 AM, Smithies, Russell
> <Russell.Smithies@agresearch.co.nz>  wrote:
>> It’s always eth0 that shows a different aggregator ID. Changing the
cables
>> around so it hits a different port on the switch makes no difference.
The
>> switch is correctly configured for the port channel.
>>
>> The only difference between the 2 servers is one is running Xen
>> (kernel-xen-2.6.18-194.32.1.el5.centos.plus) so I have the usual
virtual
>> interfaces and bridges.
>>
>>
>>
>> Any ideas what might be happening?
>>
>> Is something that needs to be “fixed” or is it not really a problem?
>> eth0      Link encap:Ethernet  HWaddr 1C:C1:DE:74:97:5C
>> peth0     Link encap:Ethernet  HWaddr FE:FF:FF:FF:FF:FF
> The presence of "peth0" shows you still use the default
xend''s
> network-bridge script. Comment it out from /etc/xen/xend-config.sxp,
> and create bridges manually on top of your bonding using OS config
> files (/etc/sysconfig/network-scripts/ifcfg-br*). There''s a recent
> example on this list (with vlans on top of bonding) from Donny Brooks,
> search the archive if you need it.
>If you need help setting this up I may can help. I have it running 
properly on a few centos 5.5 machines with xen4 currently. I know how 
frustrating it can be too.

_______________________________________________
Xen-users mailing list
Xen-users@lists.xensource.com
http://lists.xensource.com/xen-users

Apparently Analagous Threads

Search for more possibly parallel threads

Xen users - Feb 2011 - NIC bonding - missing eth0?

[Xen-users] NIC bonding - missing eth0?

Re: [Xen-users] NIC bonding - missing eth0?

Re: [Xen-users] NIC bonding - missing eth0?

Apparently Analagous Threads