Vasiliy G Tolstov
2010-Oct-22 10:29 UTC
[Xen-devel] xen pv windows drivers unnutended install
Hello. I''m succeseful install latest windows 2008 r2 data center edition and xen pv drivers (gplpv_Vista2008x64_0.11.0.238.msi). After that i have two questions: 1) Why in windows 2008 xennet does not copy network config from xen domU (ip address of netwrok interface) like in 2003 server? 2) How can i integrate xen pv drivers into windows 2008 install cd? Does some body write instruction baout it, or i need to do things, like in windows Xp unnutended install? Thank You. -- Vasiliy G Tolstov <v.tolstov@selfip.ru> Selfip.Ru _______________________________________________ Xen-devel mailing list Xen-devel@lists.xensource.com http://lists.xensource.com/xen-devel
James Harper
2010-Oct-22 23:27 UTC
RE: [Xen-devel] xen pv windows drivers unnutended install
> > Hello. I'm succeseful install latest windows 2008 r2 data center edition > and xen pv drivers (gplpv_Vista2008x64_0.11.0.238.msi). After that i > have two questions: > 1) Why in windows 2008 xennet does not copy network config from xen domU > (ip address of netwrok interface) like in 2003 server?I don't know. I thought it did but I haven't really tested it under anything but XP/2003. After install but before reboot (eg when the rtl8139 driver is active and the xennet driver is 'cable disconnected'), can you run copyconfig manually? In the installer, I wait until all devices are installed before running copyconfig, but maybe that's not working, or maybe the copyconfig isn't working...> > 2) How can i integrate xen pv drivers into windows 2008 install cd? Does > some body write instruction baout it, or i need to do things, like in > windows Xp unnutended install? >It's a bit tricky because the drivers aren't signed. James _______________________________________________ Xen-devel mailing list Xen-devel@lists.xensource.com http://lists.xensource.com/xen-devel
James Harper
2010-Oct-23 07:58 UTC
RE: [Xen-devel] xen pv windows drivers unnutended install
> > Hello. I'm succeseful install latest windows 2008 r2 data center edition > and xen pv drivers (gplpv_Vista2008x64_0.11.0.238.msi). After that i > have two questions: > 1) Why in windows 2008 xennet does not copy network config from xen domU > (ip address of netwrok interface) like in 2003 server? > > 2) How can i integrate xen pv drivers into windows 2008 install cd? Does > some body write instruction baout it, or i need to do things, like in > windows Xp unnutended install? >Further to my previous email, I just remembered that Windows 2008 and Vista use 1.7 of KMDF (Kernel Mode Driver Framework), and GPLPV uses 1.9. When no KMDF is installed (eg 2000, XP, 2003), the installer installs its version of KMDF and then the drivers can run (a reboot is still required to activate them of course) When the same version or newer of KMDF is already installed (7 and 2008R2 both use 1.9) then the drivers can run. When an older version is already installed, KMDF must be updated, then the system must be rebooted, then the drivers can run. This means that when the installer runs, a reboot is required before the xennet driver can start up and so no network config can been installed yet, and then another reboot is required before the drivers can take control of the system and disable the qemu network and disk devices. I'm not sure what this means for integrating GPLPV into Windows Vista and 2008, as you'd need to make sure KMDF is installed too. James _______________________________________________ Xen-devel mailing list Xen-devel@lists.xensource.com http://lists.xensource.com/xen-devel