I''ve been trying to get VT-D working wiht xen for quite some time,
since
3.4.2, and I''ve always had issues with my RAID controller not working
properly when iommu is not disabled in Xen:
lspci outpuut for the card:
05:0e.0 RAID bus controller: Dell PowerEdge Expandable RAID controller 5
Subsystem: Dell PERC 5/i Integrated RAID Controller
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr-
Stepping+ SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 64 (32000ns min), Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 18
Region 0: Memory at f2ff0000 (32-bit, prefetchable) [size=64K]
Region 2: Memory at fbce0000 (32-bit, non-prefetchable) [size=128K]
Expansion ROM at fbcd0000 [disabled] [size=32K]
Capabilities: [c0] Power Management version 2
Flags: PMEClk- DSI- D1+ D2- AuxCurrent=0mA
PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [d0] Message Signalled Interrupts: Mask- 64bit+ Queue=0/1
Enable-
Address: 0000000000000000 Data: 0000
Capabilities: [e0] PCI-X non-bridge device
Command: DPERE- ERO- RBC=512 OST=4
Status: Dev=05:0e.0 64bit+ 133MHz+ SCD- USC- DC=bridge DMMRBC=1024
DMOST=4 DMCRS=16 RSCEM- 266MHz- 533MHz-
Kernel driver in use: megaraid_sas
Kernel modules: megaraid_sas
I am using a Supermicro X8DALi motherboard with a 5500 chipset.
Whenever I try to access the device the Xen console spits out something
like this:
(XEN) [VT-D]iommu.c:796: DMAR:[DMA Write] Request device [05:08.0] fault
addr 204865000, iommu reg = ffff82c3fff57000
(XEN) DMAR:[fault reason 02h] Present bit in context entry is clear
(XEN) print_vtd_entries: iommu = ffff83013fffaee0 bdf = 5:8.0 gmfn 204865
(XEN) root_entry = ffff83013ff37000
(XEN) root_entry[5] = 13cf12001
(XEN) context = ffff83013cf12000
(XEN) context[40] = 0_0
(XEN) ctxt_entry[40] not present
(XEN) [VT-D]iommu.c:821: iommu_fault_status: Primary Pending Fault
reads are partially succcessful, but I am getting seek errors at times,
filesystems will mount properly but I cannot use any of them properly..
The actual kernel output varies, sometimes i get EINVAL when I try to
read from the filesystem, sometimes it simply refuses to at all
recognize the disk altogether, and other times it will hang the entire
system, including the hypervisor itself.
I''ve tried booting the hypervisor with x2apic disabled, but to no
effect. I''ve also tried with the latest xen-4.0-testing (4.0.1), buut
same issue and same outpuut
A quick google turns up a thread, from this mailing list, with a
different RAID card, but the kernel output is similar.. e.g.
scsi scan: INQUIRY result too short (5), using 36
http://lists.xensource.com/archives/html/xen-users/2010-04/msg00535.html
The full xen log is below
L __ __ _ _ ___
___
\ \/ /___ _ __ | || | / _ \ / _ \ 0x146000>, shtab=0x3a2078,
entry=0x100000
\ // _ \ ''_ \ | || |_| | | | | |
|
/ \ __/ | | | |__ _| |_| | |_| |apper/OS-root ro nomodeset
console=tty0 r
/_/\_\___|_| |_| |
_|(_)___(_)___/
020
bytes]
(XEN) Xen version 4.0.0 (mordy@) (gcc version 4.3.2 (Debian 4.3.2-1.1) )
Fri May 21 07:50:16 PDT 2010boot-module
@
(XEN) Latest ChangeSet:
unavailable
(XEN) Console output is
synchronous.
(XEN) Command line: iommu=verbose loglvl=all guest_loglvl=all
sync_console console_to_rint com1=115200,8n1
console=com1
(XEN) Video
information:
(XEN) VGA is text mode 80x25, font
8x16
(XEN) VBE/DDC methods: none; EDID transfer time: 0
seconds
(XEN) EDID info not retrieved because no DDC retrieval method
detected
(XEN) Disc information:
(XEN) Found 1 MBR signatures
(XEN) Found 1 EDD information structures
(XEN) Xen-e820 RAM map:
(XEN) 0000000000000000 - 000000000009a000 (usable)
(XEN) 000000000009a000 - 00000000000a0000 (reserved)
(XEN) 00000000000e0000 - 0000000000100000 (reserved)
(XEN) 0000000000100000 - 00000000bf760000 (usable)
(XEN) 00000000bf76e000 - 00000000bf770000 type 9
(XEN) 00000000bf770000 - 00000000bf77e000 (ACPI data)
(XEN) 00000000bf77e000 - 00000000bf7d0000 (ACPI NVS)
(XEN) 00000000bf7d0000 - 00000000bf7e0000 (reserved)
(XEN) 00000000bf7ec000 - 00000000c0000000 (reserved)
(XEN) 00000000fee00000 - 00000000fee01000 (reserved)
(XEN) 00000000ffc00000 - 0000000100000000 (reserved)
(XEN) 0000000100000000 - 0000000340000000 (usable)
(XEN) ACPI: RSDP 000F9E10, 0024 (r2 ACPIAM)
(XEN) ACPI: XSDT BF770100, 0094 (r1 NEC 20090424 MSFT
97)
(XEN) ACPI: FACP BF770290, 00F4 (r4 042409 FACP1917 20090424 MSFT
97)
(XEN) ACPI: DSDT BF770670, 5BFB (r2 10601 10601000 0 INTL
20051117)
(XEN) ACPI: FACS BF77E000, 0040
(XEN) ACPI: APIC BF770390, 00D2 (r2 042409 APIC1917 20090424 MSFT
97)
(XEN) ACPI: MCFG BF770470, 003C (r1 042409 OEMMCFG 20090424 MSFT
97)
(XEN) ACPI: SLIC BF7704B0, 0176 (r1 NEC 20090424 MSFT
97)
(XEN) ACPI: ERST BF770630, 0040 (r1 042409 WHEA1917 20090424 MSFT
97)
(XEN) ACPI: OEMB BF77E040, 007B (r1 042409 OEMB1917 20090424 MSFT
97)
(XEN) ACPI: SRAT BF77A670, 01D0 (r1 042409 OEMSRAT 1 INTL
1)
(XEN) ACPI: HPET BF77A840, 0038 (r1 042409 OEMHPET 20090424 MSFT
97)
(XEN) ACPI: DMAR BF77E0C0, 0118 (r1 AMI OEMDMAR 1 MSFT
97)
(XEN) ACPI: SSDT BF781DF0, 0363 (r1 DpgPmm CpuPm 12 INTL
20051117)
(XEN) ACPI: EINJ BF77A880, 0130 (r1 AMIER AMI_EINJ 20090424 MSFT
97)
(XEN) ACPI: BERT BF77AA10, 0030 (r1 AMIER AMI_BERT 20090424 MSFT
97)
(XEN) ACPI: ERST BF77AA40, 01B0 (r1 AMIER AMI_ERST 20090424 MSFT
97)
(XEN) ACPI: HEST BF77ABF0, 00A8 (r1 AMIER AMI_HEST 20090424 MSFT
97)
(XEN) System RAM: 12045MB (12334808kB)
(XEN) SRAT: PXM 0 -> APIC 0 -> Node 0
(XEN) SRAT: PXM 0 -> APIC 2 -> Node 0
(XEN) SRAT: PXM 0 -> APIC 4 -> Node 0
(XEN) SRAT: PXM 0 -> APIC 6 -> Node 0
(XEN) SRAT: PXM 0 -> APIC 1 -> Node 0
(XEN) SRAT: PXM 0 -> APIC 3 -> Node 0
(XEN) SRAT: PXM 0 -> APIC 5 -> Node 0
(XEN) SRAT: PXM 0 -> APIC 7 -> Node 0
(XEN) SRAT: PXM 1 -> APIC 16 -> Node 1
(XEN) SRAT: PXM 1 -> APIC 18 -> Node 1
(XEN) SRAT: PXM 1 -> APIC 20 -> Node 1
(XEN) SRAT: PXM 1 -> APIC 22 -> Node 1
(XEN) SRAT: PXM 1 -> APIC 17 -> Node 1
(XEN) SRAT: PXM 1 -> APIC 19 -> Node 1
(XEN) SRAT: PXM 1 -> APIC 21 -> Node 1
(XEN) SRAT: PXM 1 -> APIC 23 -> Node 1
(XEN) SRAT: Node 0 PXM 0 0-a0000
(XEN) SRAT: Node 0 PXM 0 100000-c0000000
(XEN) SRAT: Node 0 PXM 0 100000000-1c0000000
(XEN) SRAT: Node 1 PXM 1 1c0000000-340000000
(XEN) NUMA: Allocated memnodemap from 33fdfb000 - 33fdff000
(XEN) NUMA: Using 8 for the hash shift.
(XEN) Domain heap initialised DMA width 30 bits
(XEN) found SMP MP-table at 000ff780
(XEN) DMI present.
(XEN) Using APIC driver default
(XEN) ACPI: PM-Timer IO Port: 0x808
(XEN) ACPI: ACPI SLEEP INFO: pm1x_cnt[804,0], pm1x_evt[800,0]
(XEN) ACPI: wakeup_vec[bf77e00c], vec_size[20]
(XEN) ACPI: Local APIC address 0xfee00000
(XEN) ACPI: LAPIC (acpi_id[0x01] lapic_id[0x00] enabled)
(XEN) Processor #0 7:10 APIC version 21
(XEN) ACPI: LAPIC (acpi_id[0x02] lapic_id[0x10] enabled)
(XEN) Processor #16 7:10 APIC version 21
(XEN) ACPI: LAPIC (acpi_id[0x03] lapic_id[0x02] enabled)
(XEN) Processor #2 7:10 APIC version 21
(XEN) ACPI: LAPIC (acpi_id[0x04] lapic_id[0x12] enabled)
(XEN) Processor #18 7:10 APIC version 21
(XEN) ACPI: LAPIC (acpi_id[0x05] lapic_id[0x04] enabled)
(XEN) Processor #4 7:10 APIC version 21
(XEN) ACPI: LAPIC (acpi_id[0x06] lapic_id[0x14] enabled)
(XEN) Processor #20 7:10 APIC version 21
(XEN) ACPI: LAPIC (acpi_id[0x07] lapic_id[0x06] enabled)
(XEN) Processor #6 7:10 APIC version 21
(XEN) ACPI: LAPIC (acpi_id[0x08] lapic_id[0x16] enabled)
(XEN) Processor #22 7:10 APIC version 21
(XEN) ACPI: LAPIC (acpi_id[0x09] lapic_id[0x01] enabled)
(XEN) Processor #1 7:10 APIC version 21
(XEN) ACPI: LAPIC (acpi_id[0x0a] lapic_id[0x11] enabled)
(XEN) Processor #17 7:10 APIC version 21
(XEN) ACPI: LAPIC (acpi_id[0x0b] lapic_id[0x03] enabled)
(XEN) Processor #3 7:10 APIC version 21
(XEN) ACPI: LAPIC (acpi_id[0x0c] lapic_id[0x13] enabled)
(XEN) Processor #19 7:10 APIC version 21
(XEN) ACPI: LAPIC (acpi_id[0x0d] lapic_id[0x05] enabled)
(XEN) Processor #5 7:10 APIC version 21
(XEN) ACPI: LAPIC (acpi_id[0x0e] lapic_id[0x15] enabled)
(XEN) Processor #21 7:10 APIC version 21
(XEN) ACPI: LAPIC (acpi_id[0x0f] lapic_id[0x07] enabled)
(XEN) Processor #7 7:10 APIC version 21
(XEN) ACPI: LAPIC (acpi_id[0x10] lapic_id[0x17] enabled)
(XEN) Processor #23 7:10 APIC version 21
(XEN) ACPI: LAPIC_NMI (acpi_id[0xff] dfl dfl lint[0x1])
(XEN) Overriding APIC driver with bigsmp
(XEN) ACPI: IOAPIC (id[0x08] address[0xfec00000] gsi_base[0])
(XEN) IOAPIC[0]: apic_id 8, version 32, address 0xfec00000, GSI 0-23
(XEN) ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
(XEN) ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 20 low level)
(XEN) ACPI: IRQ0 used by override.
(XEN) ACPI: IRQ2 used by override.
(XEN) ACPI: IRQ9 used by override.
(XEN) Enabling APIC mode: Phys. Using 1 I/O APICs
(XEN) ACPI: HPET id: 0xffffffff base: 0xfed00000
(XEN) [VT-D]dmar.c:679: Host address width 40
(XEN) [VT-D]dmar.c:694: found ACPI_DMAR_DRHD:
(XEN) [VT-D]dmar.c:398: dmaru->address = fbffe000
(XEN) [VT-D]dmar.c:340: IOAPIC: f0:1f.7
(XEN) [VT-D]dmar.c:411: flags: INCLUDE_ALL
(XEN) [VT-D]dmar.c:699: found ACPI_DMAR_RMRR:
(XEN) [VT-D]dmar.c:334: endpoint: 0:1d.0
(XEN) [VT-D]dmar.c:334: endpoint: 0:1d.1
(XEN) [VT-D]dmar.c:334: endpoint: 0:1d.2
(XEN) [VT-D]dmar.c:334: endpoint: 0:1d.7
(XEN) [VT-D]dmar.c:334: endpoint: 0:1a.0
(XEN) [VT-D]dmar.c:334: endpoint: 0:1a.1
(XEN) [VT-D]dmar.c:334: endpoint: 0:1a.2
(XEN) [VT-D]dmar.c:334: endpoint: 0:1a.7
(XEN) [VT-D]dmar.c:571: RMRR region: base_addr ec000 end_address effff
(XEN) [VT-D]dmar.c:699: found ACPI_DMAR_RMRR:
(XEN) [VT-D]dmar.c:334: endpoint: 0:1d.0
(XEN) [VT-D]dmar.c:334: endpoint: 0:1d.1
(XEN) [VT-D]dmar.c:334: endpoint: 0:1d.2
(XEN) [VT-D]dmar.c:334: endpoint: 0:1d.7
(XEN) [VT-D]dmar.c:334: endpoint: 0:1a.0
(XEN) [VT-D]dmar.c:334: endpoint: 0:1a.1
(XEN) [VT-D]dmar.c:334: endpoint: 0:1a.2
(XEN) [VT-D]dmar.c:334: endpoint: 0:1a.7
(XEN) [VT-D]dmar.c:571: RMRR region: base_addr bf7ec000 end_address
bf7fffff
(XEN) [VT-D]dmar.c:704: found ACPI_DMAR_ATSR:
(XEN) [VT-D]dmar.c:599: atsru->all_ports: 0
(XEN) [VT-D]dmar.c:320: bridge: 0:1.0 start = 0 sec = 1 sub = 1
(XEN) [VT-D]dmar.c:320: bridge: 0:3.0 start = 0 sec = 2 sub = 2
(XEN) [VT-D]dmar.c:320: bridge: 0:7.0 start = 0 sec = 3 sub = 3
(XEN) PCI: MCFG configuration 0: base e0000000 segment 0 buses 0 - 255
(XEN) PCI: Not using MMCONFIG.
(XEN) Using ACPI (MADT) for SMP configuration information
(XEN) Using scheduler: SMP Credit Scheduler (credit)
(XEN) Detected 2266.790 MHz processor.
(XEN) Initing memory sharing.
(XEN) VMX: Supported advanced features:
(XEN) - APIC MMIO access virtualisation
(XEN) - APIC TPR shadow
(XEN) - Extended Page Tables (EPT)
(XEN) - Virtual-Processor Identifiers (VPID)
(XEN) - Virtual NMI
(XEN) - MSR direct-access bitmap
(XEN) HVM: ASIDs enabled.
(XEN) HVM: VMX enabled
(XEN) HVM: Hardware Assisted Paging detected.
(XEN) Intel machine check reporting enabled
(XEN) [VT-D]iommu.c:1078: drhd->address = fbffe000 iommu->reg
ffff82c3fff57000
(XEN) [VT-D]iommu.c:1080: cap = c90780106f0462 ecap = f0207e
(XEN) Intel VT-d Snoop Control not supported.
(XEN) Intel VT-d DMA Passthrough not supported.
(XEN) Intel VT-d Queued Invalidation supported.
(XEN) Intel VT-d Interrupt Remapping supported.
(XEN) I/O virtualisation enabled
(XEN) I/O virtualisation for PV guests disabled
(XEN) Total of 16 processors activated.
(XEN) ENABLING IO-APIC IRQs
(XEN) -> Using new ACK method
(XEN) ..TIMER: vector=0xF0 apic1=0 pin1=2 apic2=-1 pin2=-1
(XEN) TSC is reliable, synchronization unnecessary
(XEN) Platform timer is 14.318MHz HPET
?(XEN) Allocated console ring of 128 KiB.
(XEN) microcode.c:73:d32767 microcode: CPU1 resumed
(XEN) microcode.c:73:d32767 microcode: CPU9 resumed
(XEN) microcode.c:73:d32767 microcode: CPU14 resumed
(XEN) microcode.c:73:d32767 microcode: CPU6 resumed
(XEN) microcode.c:73:d32767 microcode: CPU3 resumed
(XEN) microcode.c:73:d32767 microcode: CPU11 resumed
(XEN) microcode.c:73:d32767 microcode: CPU8 resumed
(XEN) microcode.c:73:d32767 microcode: CPU7 resumed
(XEN) microcode.c:73:d32767 microcode: CPU15 resumed
(XEN) microcode.c:73:d32767 microcode: CPU2 resumed
(XEN) microcode.c:73:d32767 microcode: CPU5 resumed
(XEN) microcode.c:73:d32767 microcode: CPU13 resumed
(XEN) microcode.c:73:d32767 microcode: CPU4 resumed
(XEN) microcode.c:73:d32767 microcode: CPU10 resumed
(XEN) Brought up 16 CPUs
(XEN) microcode.c:73:d32767 microcode: CPU12 resumed
(XEN) Turbo Mode detected!
(XEN) HPET''s MSI mode hasn''t been supported when Interrupt
Remapping is
enabled.
(XEN) ACPI sleep modes: S3
(XEN) mcheck_poll: Machine check polling timer started.
(XEN) [VT-D]iommu.c:1325: d0:PCIe: map bdf = 0:0.0
(XEN) [VT-D]iommu.c:1325: d0:PCIe: map bdf = 0:14.0
(XEN) [VT-D]iommu.c:1325: d0:PCIe: map bdf = 0:14.1
(XEN) [VT-D]iommu.c:1325: d0:PCIe: map bdf = 0:14.2
(XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = 0:14.3
(XEN) [VT-D]iommu.c:1325: d0:PCIe: map bdf = 0:16.0
(XEN) [VT-D]iommu.c:1325: d0:PCIe: map bdf = 0:16.1
(XEN) [VT-D]iommu.c:1325: d0:PCIe: map bdf = 0:16.2
(XEN) [VT-D]iommu.c:1325: d0:PCIe: map bdf = 0:16.3
(XEN) [VT-D]iommu.c:1325: d0:PCIe: map bdf = 0:16.4
(XEN) [VT-D]iommu.c:1325: d0:PCIe: map bdf = 0:16.5
(XEN) [VT-D]iommu.c:1325: d0:PCIe: map bdf = 0:16.6
(XEN) [VT-D]iommu.c:1325: d0:PCIe: map bdf = 0:16.7
(XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = 0:1a.0
(XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = 0:1a.1
(XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = 0:1a.2
(XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = 0:1a.7
(XEN) [VT-D]iommu.c:1325: d0:PCIe: map bdf = 0:1b.0
(XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = 0:1d.0
(XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = 0:1d.1
(XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = 0:1d.2
(XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = 0:1d.7
(XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = 0:1f.0
(XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = 0:1f.2
(XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = 0:1f.3
(XEN) [VT-D]iommu.c:1325: d0:PCIe: map bdf = 1:0.0
(XEN) [VT-D]iommu.c:1325: d0:PCIe: map bdf = 3:0.0
(XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = 5:e.0
(XEN) [VT-D]iommu.c:1325: d0:PCIe: map bdf = 7:0.0
(XEN) [VT-D]iommu.c:1325: d0:PCIe: map bdf = 8:0.0
(XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = fe:0.0
(XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = fe:0.1
(XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = fe:2.0
(XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = fe:2.1
(XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = fe:2.4
(XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = fe:2.5
(XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = fe:3.0
(XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = fe:3.1
(XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = fe:3.2
(XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = fe:3.4
(XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = fe:4.0
(XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = fe:4.1
(XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = fe:4.2
(XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = fe:4.3
(XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = fe:5.0
(XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = fe:5.1
(XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = fe:5.2
(XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = fe:5.3
(XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = fe:6.0
(XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = fe:6.1
(XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = fe:6.2
(XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = fe:6.3
(XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = ff:0.0
(XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = ff:0.1
(XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = ff:2.0
(XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = ff:2.1
(XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = ff:2.4
(XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = ff:2.5
(XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = ff:3.0
(XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = ff:3.1
(XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = ff:3.2
(XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = ff:3.4
(XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = ff:4.0
(XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = ff:4.1
(XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = ff:4.2
(XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = ff:4.3
(XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = ff:5.0
(XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = ff:5.1
(XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = ff:5.2
(XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = ff:5.3
(XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = ff:6.0
(XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = ff:6.1
(XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = ff:6.2
(XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = ff:6.3
(XEN) [VT-D]iommu.c:695: iommu_enable_translation: iommu->reg
ffff82c3fff57000
(XEN) *** LOADING DOMAIN 0 ***
(XEN) Xen kernel: 64-bit, lsb, compat32
(XEN) Dom0 kernel: 64-bit, PAE, lsb, paddr 0x1000000 -> 0x26b6000
(XEN) PHYSICAL MEMORY ARRANGEMENT:
(XEN) Dom0 alloc.: 0000000100000000->0000000120000000 (2937045 pages
to be allocated)
(XEN) VIRTUAL MEMORY ARRANGEMENT:
(XEN) Loaded kernel: ffffffff81000000->ffffffff826b6000
(XEN) Init. ramdisk: ffffffff826b6000->ffffffff8f7d7600
(XEN) Phys-Mach map: ffffffff8f7d8000->ffffffff90f406a8
(XEN) Start info: ffffffff90f41000->ffffffff90f414b4
(XEN) Page tables: ffffffff90f42000->ffffffff90fcf000
(XEN) Boot stack: ffffffff90fcf000->ffffffff90fd0000
(XEN) TOTAL: ffffffff80000000->ffffffff91400000
(XEN) ENTRY ADDRESS: ffffffff819be200
(XEN) Dom0 has maximum 16 VCPUs
(XEN) Scrubbing Free RAM: .done.
(XEN) Xen trace buffers: disabled
(XEN) Std. Loglevel: All
(XEN) Guest Loglevel: All
(XEN) **********************************************
(XEN) ******* WARNING: CONSOLE OUTPUT IS SYNCHRONOUS
(XEN) ******* This option is intended to aid debugging of Xen by
ensuring
(XEN) ******* that all output is synchronously delivered on the serial
line.
(XEN) ******* However it can introduce SIGNIFICANT latencies and affect
(XEN) ******* timekeeping. It is NOT recommended for production use!
(XEN) **********************************************
(XEN) 3... 2... 1...
(XEN) *** Serial input -> DOM0 (type ''CTRL-a'' three times
to switch
input to Xen)
(XEN) Freed 164kB init memory.
mapping kernel into physical memory
Xen: setup ISA identity maps
about to get started...
(XEN) PCI add device 00:00.0
(XEN) PCI add device 00:01.0
(XEN) PCI add device 00:03.0
(XEN) PCI add device 00:07.0
(XEN) PCI add device 00:14.0
(XEN) PCI add device 00:14.1
(XEN) PCI add device 00:14.2
(XEN) PCI add device 00:14.3
(XEN) PCI add device 00:16.0
(XEN) PCI add device 00:16.1
(XEN) PCI add device 00:16.2
(XEN) PCI add device 00:16.3
(XEN) PCI add device 00:16.4
(XEN) PCI add device 00:16.5
(XEN) PCI add device 00:16.6
(XEN) PCI add device 00:16.7
(XEN) PCI add device 00:1a.0
(XEN) PCI add device 00:1a.1
(XEN) PCI add device 00:1a.2
(XEN) PCI add device 00:1a.7
(XEN) PCI add device 00:1b.0
(XEN) PCI add device 00:1c.0
(XEN) PCI add device 00:1c.4
(XEN) PCI add device 00:1c.5
(XEN) PCI add device 00:1d.0
(XEN) PCI add device 00:1d.1
(XEN) PCI add device 00:1d.2
(XEN) PCI add device 00:1d.7
(XEN) PCI add device 00:1e.0
(XEN) PCI add device 00:1f.0
(XEN) PCI add device 00:1f.2
(XEN) PCI add device 00:1f.3
(XEN) PCI add device 01:00.0
(XEN) PCI add device 03:00.0
(XEN) PCI add device 04:00.0
(XEN) PCI add device 04:00.2
(XEN) PCI add device 05:0e.0
(XEN) PCI add device 07:00.0
(XEN) PCI add device 08:00.0
(XEN) cpuid.MWAIT[.eax=40, .ebx=40, .ecx=3, .edx=1120]
(XEN) Monitor-Mwait will be used to enter C-1 state
(XEN) cpuid.MWAIT[.eax=40, .ebx=40, .ecx=3, .edx=1120]
(XEN) Monitor-Mwait will be used to enter C-3 state
(XEN) cpuid.MWAIT[.eax=40, .ebx=40, .ecx=3, .edx=1120]
(XEN) Monitor-Mwait will be used to enter C-3 state
(XEN) cpuid.MWAIT[.eax=40, .ebx=40, .ecx=3, .edx=1120]
(XEN) Monitor-Mwait will be used to enter C-1 state
(XEN) cpuid.MWAIT[.eax=40, .ebx=40, .ecx=3, .edx=1120]
(XEN) Monitor-Mwait will be used to enter C-3 state
(XEN) cpuid.MWAIT[.eax=40, .ebx=40, .ecx=3, .edx=1120]
(XEN) Monitor-Mwait will be used to enter C-3 state
(XEN) cpuid.MWAIT[.eax=40, .ebx=40, .ecx=3, .edx=1120]
(XEN) Monitor-Mwait will be used to enter C-1 state
(XEN) cpuid.MWAIT[.eax=40, .ebx=40, .ecx=3, .edx=1120]
(XEN) Monitor-Mwait will be used to enter C-3 state
(XEN) cpuid.MWAIT[.eax=40, .ebx=40, .ecx=3, .edx=1120]
(XEN) Monitor-Mwait will be used to enter C-3 state
(XEN) cpuid.MWAIT[.eax=40, .ebx=40, .ecx=3, .edx=1120]
(XEN) Monitor-Mwait will be used to enter C-1 state
(XEN) cpuid.MWAIT[.eax=40, .ebx=40, .ecx=3, .edx=1120]
(XEN) Monitor-Mwait will be used to enter C-3 state
(XEN) cpuid.MWAIT[.eax=40, .ebx=40, .ecx=3, .edx=1120]
(XEN) Monitor-Mwait will be used to enter C-3 state
(XEN) cpuid.MWAIT[.eax=40, .ebx=40, .ecx=3, .edx=1120]
(XEN) Monitor-Mwait will be used to enter C-1 state
(XEN) cpuid.MWAIT[.eax=40, .ebx=40, .ecx=3, .edx=1120]
(XEN) Monitor-Mwait will be used to enter C-3 state
(XEN) cpuid.MWAIT[.eax=40, .ebx=40, .ecx=3, .edx=1120]
(XEN) Monitor-Mwait will be used to enter C-3 state
(XEN) cpuid.MWAIT[.eax=40, .ebx=40, .ecx=3, .edx=1120]
(XEN) Monitor-Mwait will be used to enter C-1 state
(XEN) cpuid.MWAIT[.eax=40, .ebx=40, .ecx=3, .edx=1120]
(XEN) Monitor-Mwait will be used to enter C-3 state
(XEN) cpuid.MWAIT[.eax=40, .ebx=40, .ecx=3, .edx=1120]
(XEN) Monitor-Mwait will be used to enter C-3 state
(XEN) cpuid.MWAIT[.eax=40, .ebx=40, .ecx=3, .edx=1120]
(XEN) Monitor-Mwait will be used to enter C-1 state
(XEN) cpuid.MWAIT[.eax=40, .ebx=40, .ecx=3, .edx=1120]
(XEN) Monitor-Mwait will be used to enter C-3 state
(XEN) cpuid.MWAIT[.eax=40, .ebx=40, .ecx=3, .edx=1120]
(XEN) Monitor-Mwait will be used to enter C-3 state
(XEN) cpuid.MWAIT[.eax=40, .ebx=40, .ecx=3, .edx=1120]
(XEN) Monitor-Mwait will be used to enter C-1 state
(XEN) cpuid.MWAIT[.eax=40, .ebx=40, .ecx=3, .edx=1120]
(XEN) Monitor-Mwait will be used to enter C-3 state
(XEN) cpuid.MWAIT[.eax=40, .ebx=40, .ecx=3, .edx=1120]
(XEN) Monitor-Mwait will be used to enter C-3 state
(XEN) cpuid.MWAIT[.eax=40, .ebx=40, .ecx=3, .edx=1120]
(XEN) Monitor-Mwait will be used to enter C-1 state
(XEN) cpuid.MWAIT[.eax=40, .ebx=40, .ecx=3, .edx=1120]
(XEN) Monitor-Mwait will be used to enter C-3 state
(XEN) cpuid.MWAIT[.eax=40, .ebx=40, .ecx=3, .edx=1120]
(XEN) Monitor-Mwait will be used to enter C-3 state
(XEN) cpuid.MWAIT[.eax=40, .ebx=40, .ecx=3, .edx=1120]
(XEN) Monitor-Mwait will be used to enter C-1 state
(XEN) cpuid.MWAIT[.eax=40, .ebx=40, .ecx=3, .edx=1120]
(XEN) Monitor-Mwait will be used to enter C-3 state
(XEN) cpuid.MWAIT[.eax=40, .ebx=40, .ecx=3, .edx=1120]
(XEN) Monitor-Mwait will be used to enter C-3 state
(XEN) cpuid.MWAIT[.eax=40, .ebx=40, .ecx=3, .edx=1120]
(XEN) Monitor-Mwait will be used to enter C-1 state
(XEN) cpuid.MWAIT[.eax=40, .ebx=40, .ecx=3, .edx=1120]
(XEN) Monitor-Mwait will be used to enter C-3 state
(XEN) cpuid.MWAIT[.eax=40, .ebx=40, .ecx=3, .edx=1120]
(XEN) Monitor-Mwait will be used to enter C-3 state
(XEN) cpuid.MWAIT[.eax=40, .ebx=40, .ecx=3, .edx=1120]
(XEN) Monitor-Mwait will be used to enter C-1 state
(XEN) cpuid.MWAIT[.eax=40, .ebx=40, .ecx=3, .edx=1120]
(XEN) Monitor-Mwait will be used to enter C-3 state
(XEN) cpuid.MWAIT[.eax=40, .ebx=40, .ecx=3, .edx=1120]
(XEN) Monitor-Mwait will be used to enter C-3 state
(XEN) cpuid.MWAIT[.eax=40, .ebx=40, .ecx=3, .edx=1120]
(XEN) Monitor-Mwait will be used to enter C-1 state
(XEN) cpuid.MWAIT[.eax=40, .ebx=40, .ecx=3, .edx=1120]
(XEN) Monitor-Mwait will be used to enter C-3 state
(XEN) cpuid.MWAIT[.eax=40, .ebx=40, .ecx=3, .edx=1120]
(XEN) Monitor-Mwait will be used to enter C-3 state
(XEN) cpuid.MWAIT[.eax=40, .ebx=40, .ecx=3, .edx=1120]
(XEN) Monitor-Mwait will be used to enter C-1 state
(XEN) cpuid.MWAIT[.eax=40, .ebx=40, .ecx=3, .edx=1120]
(XEN) Monitor-Mwait will be used to enter C-3 state
(XEN) cpuid.MWAIT[.eax=40, .ebx=40, .ecx=3, .edx=1120]
(XEN) Monitor-Mwait will be used to enter C-3 state
(XEN) cpuid.MWAIT[.eax=40, .ebx=40, .ecx=3, .edx=1120]
(XEN) Monitor-Mwait will be used to enter C-1 state
(XEN) cpuid.MWAIT[.eax=40, .ebx=40, .ecx=3, .edx=1120]
(XEN) Monitor-Mwait will be used to enter C-3 state
(XEN) cpuid.MWAIT[.eax=40, .ebx=40, .ecx=3, .edx=1120]
(XEN) Monitor-Mwait will be used to enter C-3 state
(XEN) cpuid.MWAIT[.eax=40, .ebx=40, .ecx=3, .edx=1120]
(XEN) Monitor-Mwait will be used to enter C-1 state
(XEN) cpuid.MWAIT[.eax=40, .ebx=40, .ecx=3, .edx=1120]
(XEN) Monitor-Mwait will be used to enter C-3 state
(XEN) cpuid.MWAIT[.eax=40, .ebx=40, .ecx=3, .edx=1120]
(XEN) Monitor-Mwait will be used to enter C-3 state
(XEN) irq.c:1139:d0 Cannot bind IRQ 4 to guest. In use by
''ns16550''.
(XEN) irq.c:1139:d0 Cannot bind IRQ 2 to guest. In use by
''cascade''.
(XEN) irq.c:1139:d0 Cannot bind IRQ 4 to guest. In use by
''ns16550''.
(XEN) irq.c:1139:d0 Cannot bind IRQ 2 to guest. In use by
''cascade''.
(XEN) irq.c:1139:d0 Cannot bind IRQ 4 to guest. In use by
''ns16550''.
(XEN) irq.c:1139:d0 Cannot bind IRQ 2 to guest. In use by
''cascade''.
(XEN) irq.c:1139:d0 Cannot bind IRQ 4 to guest. In use by
''ns16550''.
(XEN) irq.c:1139:d0 Cannot bind IRQ 2 to guest. In use by
''cascade''.
(XEN) [VT-D]iommu.c:821: iommu_fault_status: Primary Pending Fault
(XEN) [VT-D]iommu.c:796: DMAR:[DMA Write] Request device [05:08.0] fault
addr 203a09000, iommu reg = ffff82c3fff57000
(XEN) DMAR:[fault reason 02h] Present bit in context entry is clear
(XEN) print_vtd_entries: iommu = ffff83013fffaee0 bdf = 5:8.0 gmfn 203a09
(XEN) root_entry = ffff83013ff37000
(XEN) root_entry[5] = 13cf12001
(XEN) context = ffff83013cf12000
(XEN) context[40] = 0_0
(XEN) ctxt_entry[40] not present
(XEN) [VT-D]iommu.c:796: DMAR:[DMA Write] Request device [05:08.0] fault
addr 203eba000, iommu reg = ffff82c3fff57000
(XEN) DMAR:[fault reason 02h] Present bit in context entry is clear
(XEN) print_vtd_entries: iommu = ffff83013fffaee0 bdf = 5:8.0 gmfn 203eba
(XEN) root_entry = ffff83013ff37000
(XEN) root_entry[5] = 13cf12001
(XEN) context = ffff83013cf12000
(XEN) context[40] = 0_0
(XEN) ctxt_entry[40] not present
(XEN) [VT-D]iommu.c:821: iommu_fault_status: Primary Pending Fault
(XEN) [VT-D]iommu.c:796: DMAR:[DMA Write] Request device [05:08.0] fault
addr 204e11000, iommu reg = ffff82c3fff57000
(XEN) DMAR:[fault reason 02h] Present bit in context entry is clear
(XEN) print_vtd_entries: iommu = ffff83013fffaee0 bdf = 5:8.0 gmfn 204e11
(XEN) root_entry = ffff83013ff37000
(XEN) root_entry[5] = 13cf12001
(XEN) context = ffff83013cf12000
(XEN) context[40] = 0_0
(XEN) ctxt_entry[40] not present
(XEN) [VT-D]iommu.c:821: iommu_fault_status: Primary Pending Fault
(XEN) [VT-D]iommu.c:796: DMAR:[DMA Write] Request device [05:08.0] fault
addr 2061e2000, iommu reg = ffff82c3fff57000
(XEN) DMAR:[fault reason 02h] Present bit in context entry is clear
(XEN) print_vtd_entries: iommu = ffff83013fffaee0 bdf = 5:8.0 gmfn 2061e2
(XEN) root_entry = ffff83013ff37000
(XEN) root_entry[5] = 13cf12001
(XEN) context = ffff83013cf12000
(XEN) context[40] = 0_0
(XEN) ctxt_entry[40] not present
(XEN) [VT-D]iommu.c:796: DMAR:[DMA Write] Request device [05:08.0] fault
addr 205043000, iommu reg = ffff82c3fff57000
(XEN) DMAR:[fault reason 02h] Present bit in context entry is clear
(XEN) print_vtd_entries: iommu = ffff83013fffaee0 bdf = 5:8.0 gmfn 205043
(XEN) root_entry = ffff83013ff37000
(XEN) root_entry[5] = 13cf12001
(XEN) context = ffff83013cf12000
(XEN) context[40] = 0_0
(XEN) ctxt_entry[40] not present
(XEN) [VT-D]iommu.c:821: iommu_fault_status: Primary Pending Fault
(XEN) [VT-D]iommu.c:796: DMAR:[DMA Write] Request device [05:08.0] fault
addr 20552b000, iommu reg = ffff82c3fff57000
(XEN) DMAR:[fault reason 02h] Present bit in context entry is clear
(XEN) print_vtd_entries: iommu = ffff83013fffaee0 bdf = 5:8.0 gmfn 20552b
(XEN) root_entry = ffff83013ff37000
(XEN) root_entry[5] = 13cf12001
(XEN) context = ffff83013cf12000
(XEN) context[40] = 0_0
(XEN) ctxt_entry[40] not present
(XEN) [VT-D]iommu.c:821: iommu_fault_status: Primary Pending Fault
(XEN) [VT-D]iommu.c:796: DMAR:[DMA Write] Request device [05:08.0] fault
addr 205708000, iommu reg = ffff82c3fff57000
(XEN) DMAR:[fault reason 02h] Present bit in context entry is clear
(XEN) print_vtd_entries: iommu = ffff83013fffaee0 bdf = 5:8.0 gmfn 205708
(XEN) root_entry = ffff83013ff37000
(XEN) root_entry[5] = 13cf12001
(XEN) context = ffff83013cf12000
(XEN) context[40] = 0_0
(XEN) ctxt_entry[40] not present
(XEN) [VT-D]iommu.c:796: DMAR:[DMA Write] Request device [05:08.0] fault
addr 2060c0000, iommu reg = ffff82c3fff57000
(XEN) DMAR:[fault reason 02h] Present bit in context entry is clear
(XEN) print_vtd_entries: iommu = ffff83013fffaee0 bdf = 5:8.0 gmfn 2060c0
(XEN) root_entry = ffff83013ff37000
(XEN) root_entry[5] = 13cf12001
(XEN) context = ffff83013cf12000
(XEN) context[40] = 0_0
(XEN) ctxt_entry[40] not present
(XEN) [VT-D]iommu.c:821: iommu_fault_status: Primary Pending Fault
(XEN) [VT-D]iommu.c:796: DMAR:[DMA Write] Request device [05:08.0] fault
addr 206591000, iommu reg = ffff82c3fff57000
(XEN) DMAR:[fault reason 02h] Present bit in context entry is clear
(XEN) print_vtd_entries: iommu = ffff83013fffaee0 bdf = 5:8.0 gmfn 206591
(XEN) root_entry = ffff83013ff37000
(XEN) root_entry[5] = 13cf12001
(XEN) context = ffff83013cf12000
(XEN) context[40] = 0_0
(XEN) ctxt_entry[40] not present
(XEN) [VT-D]iommu.c:796: DMAR:[DMA Write] Request device [05:08.0] fault
addr 204353000, iommu reg = ffff82c3fff57000
(XEN) DMAR:[fault reason 02h] Present bit in context entry is clear
(XEN) print_vtd_entries: iommu = ffff83013fffaee0 bdf = 5:8.0 gmfn 204353
(XEN) root_entry = ffff83013ff37000
(XEN) root_entry[5] = 13cf12001
(XEN) context = ffff83013cf12000
(XEN) context[40] = 0_0
(XEN) ctxt_entry[40] not present
(XEN) [VT-D]iommu.c:821: iommu_fault_status: Primary Pending Fault
(XEN) [VT-D]iommu.c:796: DMAR:[DMA Write] Request device [05:08.0] fault
addr 2061f2000, iommu reg = ffff82c3fff57000
(XEN) DMAR:[fault reason 02h] Present bit in context entry is clear
(XEN) print_vtd_entries: iommu = ffff83013fffaee0 bdf = 5:8.0 gmfn 2061f2
(XEN) root_entry = ffff83013ff37000
(XEN) root_entry[5] = 13cf12001
(XEN) context = ffff83013cf12000
(XEN) context[40] = 0_0
(XEN) ctxt_entry[40] not present
(XEN) [VT-D]iommu.c:796: DMAR:[DMA Write] Request device [05:08.0] fault
addr 204306000, iommu reg = ffff82c3fff57000
(XEN) DMAR:[fault reason 02h] Present bit in context entry is clear
(XEN) print_vtd_entries: iommu = ffff83013fffaee0 bdf = 5:8.0 gmfn 204306
(XEN) root_entry = ffff83013ff37000
(XEN) root_entry[5] = 13cf12001
(XEN) context = ffff83013cf12000
(XEN) context[40] = 0_0
(XEN) ctxt_entry[40] not present
(XEN) [VT-D]iommu.c:821: iommu_fault_status: Primary Pending Fault
(XEN) [VT-D]iommu.c:796: DMAR:[DMA Write] Request device [05:08.0] fault
addr 205f6b000, iommu reg = ffff82c3fff57000
(XEN) DMAR:[fault reason 02h] Present bit in context entry is clear
(XEN) print_vtd_entries: iommu = ffff83013fffaee0 bdf = 5:8.0 gmfn 205f6b
(XEN) root_entry = ffff83013ff37000
(XEN) root_entry[5] = 13cf12001
(XEN) context = ffff83013cf12000
(XEN) context[40] = 0_0
(XEN) ctxt_entry[40] not present
(XEN) [VT-D]iommu.c:796: DMAR:[DMA Write] Request device [05:08.0] fault
addr 205665000, iommu reg = ffff82c3fff57000
(XEN) DMAR:[fault reason 02h] Present bit in context entry is clear
(XEN) print_vtd_entries: iommu = ffff83013fffaee0 bdf = 5:8.0 gmfn 205665
(XEN) root_entry = ffff83013ff37000
(XEN) root_entry[5] = 13cf12001
(XEN) context = ffff83013cf12000
(XEN) context[40] = 0_0
(XEN) ctxt_entry[40] not present
(XEN) [VT-D]iommu.c:821: iommu_fault_status: Primary Pending Fault
(XEN) [VT-D]iommu.c:796: DMAR:[DMA Write] Request device [05:08.0] fault
addr 2045a0000, iommu reg = ffff82c3fff57000
(XEN) DMAR:[fault reason 02h] Present bit in context entry is clear
(XEN) print_vtd_entries: iommu = ffff83013fffaee0 bdf = 5:8.0 gmfn 2045a0
(XEN) root_entry = ffff83013ff37000
(XEN) root_entry[5] = 13cf12001
(XEN) context = ffff83013cf12000
(XEN) context[40] = 0_0
(XEN) ctxt_entry[40] not present
(XEN) [VT-D]iommu.c:796: DMAR:[DMA Write] Request device [05:08.0] fault
addr 205669000, iommu reg = ffff82c3fff57000
(XEN) DMAR:[fault reason 02h] Present bit in context entry is clear
(XEN) print_vtd_entries: iommu = ffff83013fffaee0 bdf = 5:8.0 gmfn 205669
(XEN) root_entry = ffff83013ff37000
(XEN) root_entry[5] = 13cf12001
(XEN) context = ffff83013cf12000
(XEN) context[40] = 0_0
(XEN) ctxt_entry[40] not present
(XEN) [VT-D]iommu.c:821: iommu_fault_status: Primary Pending Fault
(XEN) [VT-D]iommu.c:796: DMAR:[DMA Write] Request device [05:08.0] fault
addr 2042c6000, iommu reg = ffff82c3fff57000
(XEN) DMAR:[fault reason 02h] Present bit in context entry is clear
(XEN) print_vtd_entries: iommu = ffff83013fffaee0 bdf = 5:8.0 gmfn 2042c6
(XEN) root_entry = ffff83013ff37000
(XEN) root_entry[5] = 13cf12001
(XEN) context = ffff83013cf12000
(XEN) context[40] = 0_0
(XEN) ctxt_entry[40] not present
(XEN) [VT-D]iommu.c:796: DMAR:[DMA Write] Request device [05:08.0] fault
addr 2061fe000, iommu reg = ffff82c3fff57000
(XEN) DMAR:[fault reason 02h] Present bit in context entry is clear
(XEN) print_vtd_entries: iommu = ffff83013fffaee0 bdf = 5:8.0 gmfn 2061fe
(XEN) root_entry = ffff83013ff37000
(XEN) root_entry[5] = 13cf12001
(XEN) context = ffff83013cf12000
(XEN) context[40] = 0_0
(XEN) ctxt_entry[40] not present
(XEN) [VT-D]iommu.c:821: iommu_fault_status: Primary Pending Fault
(XEN) [VT-D]iommu.c:796: DMAR:[DMA Write] Request device [05:08.0] fault
addr 20560a000, iommu reg = ffff82c3fff57000
(XEN) DMAR:[fault reason 02h] Present bit in context entry is clear
(XEN) print_vtd_entries: iommu = ffff83013fffaee0 bdf = 5:8.0 gmfn 20560a
(XEN) root_entry = ffff83013ff37000
(XEN) root_entry[5] = 13cf12001
(XEN) context = ffff83013cf12000
(XEN) context[40] = 0_0
(XEN) ctxt_entry[40] not present
(XEN) [VT-D]iommu.c:796: DMAR:[DMA Write] Request device [05:08.0] fault
addr 206003000, iommu reg = ffff82c3fff57000
(XEN) DMAR:[fault reason 02h] Present bit in context entry is clear
(XEN) print_vtd_entries: iommu = ffff83013fffaee0 bdf = 5:8.0 gmfn 206003
(XEN) root_entry = ffff83013ff37000
(XEN) root_entry[5] = 13cf12001
(XEN) context = ffff83013cf12000
(XEN) context[40] = 0_0
(XEN) ctxt_entry[40] not present
(XEN) [VT-D]iommu.c:821: iommu_fault_status: Primary Pending Fault
(XEN) [VT-D]iommu.c:796: DMAR:[DMA Write] Request device [05:08.0] fault
addr 20583e000, iommu reg = ffff82c3fff57000
(XEN) DMAR:[fault reason 02h] Present bit in context entry is clear
(XEN) print_vtd_entries: iommu = ffff83013fffaee0 bdf = 5:8.0 gmfn 20583e
(XEN) root_entry = ffff83013ff37000
(XEN) root_entry[5] = 13cf12001
(XEN) context = ffff83013cf12000
(XEN) context[40] = 0_0
(XEN) ctxt_entry[40] not present
(XEN) [VT-D]iommu.c:796: DMAR:[DMA Write] Request device [05:08.0] fault
addr 205615000, iommu reg = ffff82c3fff57000
(XEN) DMAR:[fault reason 02h] Present bit in context entry is clear
(XEN) print_vtd_entries: iommu = ffff83013fffaee0 bdf = 5:8.0 gmfn 205615
(XEN) root_entry = ffff83013ff37000
(XEN) root_entry[5] = 13cf12001
(XEN) context = ffff83013cf12000
(XEN) context[40] = 0_0
(XEN) ctxt_entry[40] not present
(XEN) [VT-D]iommu.c:796: DMAR:[DMA Write] Request device [05:08.0] fault
addr 204265000, iommu reg = ffff82c3fff57000
(XEN) DMAR:[fault reason 02h] Present bit in context entry is clear
(XEN) print_vtd_entries: iommu = ffff83013fffaee0 bdf = 5:8.0 gmfn 204265
(XEN) root_entry = ffff83013ff37000
(XEN) root_entry[5] = 13cf12001
(XEN) context = ffff83013cf12000
(XEN) context[40] = 0_0
(XEN) ctxt_entry[40] not present
(XEN) [VT-D]iommu.c:821: iommu_fault_status: Primary Pending Fault
(XEN) [VT-D]iommu.c:796: DMAR:[DMA Write] Request device [05:08.0] fault
addr 207498000, iommu reg = ffff82c3fff57000
(XEN) DMAR:[fault reason 02h] Present bit in context entry is clear
(XEN) print_vtd_entries: iommu = ffff83013fffaee0 bdf = 5:8.0 gmfn 207498
(XEN) root_entry = ffff83013ff37000
(XEN) root_entry[5] = 13cf12001
(XEN) context = ffff83013cf12000
(XEN) context[40] = 0_0
(XEN) ctxt_entry[40] not present
(XEN) [VT-D]iommu.c:821: iommu_fault_status: Primary Pending Fault
(XEN) [VT-D]iommu.c:796: DMAR:[DMA Write] Request device [05:08.0] fault
addr 2049d1000, iommu reg = ffff82c3fff57000
(XEN) DMAR:[fault reason 02h] Present bit in context entry is clear
(XEN) print_vtd_entries: iommu = ffff83013fffaee0 bdf = 5:8.0 gmfn 2049d1
(XEN) root_entry = ffff83013ff37000
(XEN) root_entry[5] = 13cf12001
(XEN) context = ffff83013cf12000
(XEN) context[40] = 0_0
(XEN) ctxt_entry[40] not present
(XEN) [VT-D]iommu.c:821: iommu_fault_status: Primary Pending Fault
(XEN) [VT-D]iommu.c:796: DMAR:[DMA Write] Request device [05:08.0] fault
addr 20488e000, iommu reg = ffff82c3fff57000
(XEN) DMAR:[fault reason 02h] Present bit in context entry is clear
(XEN) print_vtd_entries: iommu = ffff83013fffaee0 bdf = 5:8.0 gmfn 20488e
(XEN) root_entry = ffff83013ff37000
(XEN) root_entry[5] = 13cf12001
(XEN) context = ffff83013cf12000
(XEN) context[40] = 0_0
(XEN) ctxt_entry[40] not present
(XEN) [VT-D]iommu.c:821: iommu_fault_status: Primary Pending Fault
(XEN) [VT-D]iommu.c:796: DMAR:[DMA Write] Request device [05:08.0] fault
addr 205495000, iommu reg = ffff82c3fff57000
(XEN) DMAR:[fault reason 02h] Present bit in context entry is clear
(XEN) print_vtd_entries: iommu = ffff83013fffaee0 bdf = 5:8.0 gmfn 205495
(XEN) root_entry = ffff83013ff37000
(XEN) root_entry[5] = 13cf12001
(XEN) context = ffff83013cf12000
(XEN) context[40] = 0_0
(XEN) ctxt_entry[40] not present
(XEN) [VT-D]iommu.c:821: iommu_fault_status: Primary Pending Fault
(XEN) [VT-D]iommu.c:796: DMAR:[DMA Write] Request device [05:08.0] fault
addr 2072d8000, iommu reg = ffff82c3fff57000
(XEN) DMAR:[fault reason 02h] Present bit in context entry is clear
(XEN) print_vtd_entries: iommu = ffff83013fffaee0 bdf = 5:8.0 gmfn 2072d8
(XEN) root_entry = ffff83013ff37000
(XEN) root_entry[5] = 13cf12001
(XEN) context = ffff83013cf12000
(XEN) context[40] = 0_0
(XEN) ctxt_entry[40] not present
(XEN) [VT-D]iommu.c:821: iommu_fault_status: Primary Pending Fault
(XEN) [VT-D]iommu.c:796: DMAR:[DMA Write] Request device [05:08.0] fault
addr 2055ae000, iommu reg = ffff82c3fff57000
(XEN) DMAR:[fault reason 02h] Present bit in context entry is clear
(XEN) print_vtd_entries: iommu = ffff83013fffaee0 bdf = 5:8.0 gmfn 2055ae
(XEN) root_entry = ffff83013ff37000
(XEN) root_entry[5] = 13cf12001
(XEN) context = ffff83013cf12000
(XEN) context[40] = 0_0
(XEN) ctxt_entry[40] not present
(XEN) [VT-D]iommu.c:821: iommu_fault_status: Primary Pending Fault
(XEN) [VT-D]iommu.c:796: DMAR:[DMA Write] Request device [05:08.0] fault
addr 205544000, iommu reg = ffff82c3fff57000
(XEN) DMAR:[fault reason 02h] Present bit in context entry is clear
(XEN) print_vtd_entries: iommu = ffff83013fffaee0 bdf = 5:8.0 gmfn 205544
(XEN) root_entry = ffff83013ff37000
(XEN) root_entry[5] = 13cf12001
(XEN) context = ffff83013cf12000
(XEN) context[40] = 0_0
(XEN) ctxt_entry[40] not present
(XEN) [VT-D]iommu.c:796: DMAR:[DMA Write] Request device [05:08.0] fault
addr 204865000, iommu reg = ffff82c3fff57000
(XEN) DMAR:[fault reason 02h] Present bit in context entry is clear
(XEN) print_vtd_entries: iommu = ffff83013fffaee0 bdf = 5:8.0 gmfn 204865
(XEN) root_entry = ffff83013ff37000
(XEN) root_entry[5] = 13cf12001
(XEN) context = ffff83013cf12000
(XEN) context[40] = 0_0
(XEN) ctxt_entry[40] not present
(XEN) [VT-D]iommu.c:821: iommu_fault_status: Primary Pending Fault
(XEN) [VT-D]iommu.c:796: DMAR:[DMA Write] Request device [05:08.0] fault
addr 2074be000, iommu reg = ffff82c3fff57000
(XEN) DMAR:[fault reason 02h] Present bit in context entry is clear
(XEN) print_vtd_entries: iommu = ffff83013fffaee0 bdf = 5:8.0 gmfn 2074be
(XEN) root_entry = ffff83013ff37000
(XEN) root_entry[5] = 13cf12001
(XEN) context = ffff83013cf12000
(XEN) context[40] = 0_0
(XEN) ctxt_entry[40] not present
(XEN) [VT-D]iommu.c:796: DMAR:[DMA Write] Request device [05:08.0] fault
addr 204865000, iommu reg = ffff82c3fff57000
(XEN) DMAR:[fault reason 02h] Present bit in context entry is clear
(XEN) print_vtd_entries: iommu = ffff83013fffaee0 bdf = 5:8.0 gmfn 204865
(XEN) root_entry = ffff83013ff37000
(XEN) root_entry[5] = 13cf12001
(XEN) context = ffff83013cf12000
(XEN) context[40] = 0_0
(XEN) ctxt_entry[40] not present
(XEN) [VT-D]iommu.c:821: iommu_fault_status: Primary Pending Fault
(XEN) [VT-D]iommu.c:796: DMAR:[DMA Write] Request device [05:08.0] fault
addr 2074be000, iommu reg = ffff82c3fff57000
(XEN) DMAR:[fault reason 02h] Present bit in context entry is clear
(XEN) print_vtd_entries: iommu = ffff83013fffaee0 bdf = 5:8.0 gmfn 2074be
(XEN) root_entry = ffff83013ff37000
(XEN) root_entry[5] = 13cf12001
(XEN) context = ffff83013cf12000
(XEN) context[40] = 0_0
(XEN) ctxt_entry[40] not present
(XEN) [VT-D]iommu.c:796: DMAR:[DMA Write] Request device [05:08.0] fault
addr 204865000, iommu reg = ffff82c3fff57000
(XEN) DMAR:[fault reason 02h] Present bit in context entry is clear
(XEN) print_vtd_entries: iommu = ffff83013fffaee0 bdf = 5:8.0 gmfn 204865
(XEN) root_entry = ffff83013ff37000
(XEN) root_entry[5] = 13cf12001
(XEN) context = ffff83013cf12000
(XEN) context[40] = 0_0
(XEN) ctxt_entry[40] not present
(XEN) [VT-D]iommu.c:821: iommu_fault_status: Primary Pending Fault
(XEN) [VT-D]iommu.c:796: DMAR:[DMA Write] Request device [05:08.0] fault
addr 2074be000, iommu reg = ffff82c3fff57000
(XEN) DMAR:[fault reason 02h] Present bit in context entry is clear
(XEN) print_vtd_entries: iommu = ffff83013fffaee0 bdf = 5:8.0 gmfn 2074be
(XEN) root_entry = ffff83013ff37000
(XEN) root_entry[5] = 13cf12001
(XEN) context = ffff83013cf12000
(XEN) context[40] = 0_0
(XEN) ctxt_entry[40] not present
(XEN) [VT-D]iommu.c:796: DMAR:[DMA Write] Request device [05:08.0] fault
addr 204865000, iommu reg = ffff82c3fff57000
(XEN) DMAR:[fault reason 02h] Present bit in context entry is clear
(XEN) print_vtd_entries: iommu = ffff83013fffaee0 bdf = 5:8.0 gmfn 204865
(XEN) root_entry = ffff83013ff37000
(XEN) root_entry[5] = 13cf12001
(XEN) context = ffff83013cf12000
(XEN) context[40] = 0_0
(XEN) ctxt_entry[40] not present
(XEN) [VT-D]iommu.c:821: iommu_fault_status: Primary Pending Fault
(XEN) [VT-D]iommu.c:796: DMAR:[DMA Write] Request device [05:08.0] fault
addr 2074be000, iommu reg = ffff82c3fff57000
(XEN) DMAR:[fault reason 02h] Present bit in context entry is clear
(XEN) print_vtd_entries: iommu = ffff83013fffaee0 bdf = 5:8.0 gmfn 2074be
(XEN) root_entry = ffff83013ff37000
(XEN) root_entry[5] = 13cf12001
(XEN) context = ffff83013cf12000
(XEN) context[40] = 0_0
(XEN) ctxt_entry[40] not present
(XEN) [VT-D]iommu.c:796: DMAR:[DMA Write] Request device [05:08.0] fault
addr 204865000, iommu reg = ffff82c3fff57000
(XEN) DMAR:[fault reason 02h] Present bit in context entry is clear
(XEN) print_vtd_entries: iommu = ffff83013fffaee0 bdf = 5:8.0 gmfn 204865
(XEN) root_entry = ffff83013ff37000
(XEN) root_entry[5] = 13cf12001
(XEN) context = ffff83013cf12000
(XEN) context[40] = 0_0
(XEN) ctxt_entry[40] not present
(XEN) [VT-D]iommu.c:821: iommu_fault_status: Primary Pending Fault
(XEN) [VT-D]iommu.c:796: DMAR:[DMA Write] Request device [05:08.0] fault
addr 2074be000, iommu reg = ffff82c3fff57000
(XEN) DMAR:[fault reason 02h] Present bit in context entry is clear
(XEN) print_vtd_entries: iommu = ffff83013fffaee0 bdf = 5:8.0 gmfn 2074be
(XEN) root_entry = ffff83013ff37000
(XEN) root_entry[5] = 13cf12001
(XEN) context = ffff83013cf12000
(XEN) context[40] = 0_0
(XEN) ctxt_entry[40] not present
(XEN) [VT-D]iommu.c:796: DMAR:[DMA Write] Request device [05:08.0] fault
addr 204865000, iommu reg = ffff82c3fff57000
(XEN) DMAR:[fault reason 02h] Present bit in context entry is clear
(XEN) print_vtd_entries: iommu = ffff83013fffaee0 bdf = 5:8.0 gmfn 204865
(XEN) root_entry = ffff83013ff37000
(XEN) root_entry[5] = 13cf12001
(XEN) context = ffff83013cf12000
(XEN) context[40] = 0_0
(XEN) ctxt_entry[40] not present
(XEN) [VT-D]iommu.c:821: iommu_fault_status: Primary Pending Fault
(XEN) [VT-D]iommu.c:796: DMAR:[DMA Write] Request device [05:08.0] fault
addr 2074be000, iommu reg = ffff82c3fff57000
(XEN) DMAR:[fault reason 02h] Present bit in context entry is clear
(XEN) print_vtd_entries: iommu = ffff83013fffaee0 bdf = 5:8.0 gmfn 2074be
(XEN) root_entry = ffff83013ff37000
(XEN) root_entry[5] = 13cf12001
(XEN) context = ffff83013cf12000
(XEN) context[40] = 0_0
(XEN) ctxt_entry[40] not present
(XEN) [VT-D]iommu.c:796: DMAR:[DMA Write] Request device [05:08.0] fault
addr 204865000, iommu reg = ffff82c3fff57000
(XEN) DMAR:[fault reason 02h] Present bit in context entry is clear
(XEN) print_vtd_entries: iommu = ffff83013fffaee0 bdf = 5:8.0 gmfn 204865
(XEN) root_entry = ffff83013ff37000
(XEN) root_entry[5] = 13cf12001
(XEN) context = ffff83013cf12000
(XEN) context[40] = 0_0
(XEN) ctxt_entry[40] not present
(XEN) [VT-D]iommu.c:821: iommu_fault_status: Primary Pending Fault
(XEN) [VT-D]iommu.c:796: DMAR:[DMA Write] Request device [05:08.0] fault
addr 2074be000, iommu reg = ffff82c3fff57000
(XEN) DMAR:[fault reason 02h] Present bit in context entry is clear
(XEN) print_vtd_entries: iommu = ffff83013fffaee0 bdf = 5:8.0 gmfn 2074be
(XEN) root_entry = ffff83013ff37000
(XEN) root_entry[5] = 13cf12001
(XEN) context = ffff83013cf12000
(XEN) context[40] = 0_0
(XEN) ctxt_entry[40] not present
(XEN) context[40] = 0_0
(XEN) ctxt_entry[40] not present
(XEN) [VT-D]iommu.c:796: DMAR:[DMA Write] Request device [05:08.0] fault
addr 204865000, iommu reg = ffff82c3fff57000
(XEN) DMAR:[fault reason 02h] Present bit in context entry is clear
(XEN) print_vtd_entries: iommu = ffff83013fffaee0 bdf = 5:8.0 gmfn 204865
(XEN) root_entry = ffff83013ff37000
(XEN) root_entry[5] = 13cf12001
(XEN) context = ffff83013cf12000
(XEN) context[40] = 0_0
(XEN) ctxt_entry[40] not present
(XEN) [VT-D]iommu.c:821: iommu_fault_status: Primary Pending Fault
(XEN) [VT-D]iommu.c:796: DMAR:[DMA Write] Request device [05:08.0] fault
addr 2074be000, iommu reg = ffff82c3fff57000
(XEN) DMAR:[fault reason 02h] Present bit in context entry is clear
(XEN) print_vtd_entries: iommu = ffff83013fffaee0 bdf = 5:8.0 gmfn 2074be
(XEN) root_entry = ffff83013ff37000
(XEN) root_entry[5] = 13cf12001
(XEN) context = ffff83013cf12000
(XEN) context[40] = 0_0
(XEN) ctxt_entry[40] not present
(XEN) context[40] = 0_0
(XEN) ctxt_entry[40] not present
(XEN) [VT-D]iommu.c:796: DMAR:[DMA Write] Request device [05:08.0] fault
addr 204865000, iommu reg = ffff82c3fff57000
(XEN) DMAR:[fault reason 02h] Present bit in context entry is clear
(XEN) print_vtd_entries: iommu = ffff83013fffaee0 bdf = 5:8.0 gmfn 204865
(XEN) root_entry = ffff83013ff37000
(XEN) root_entry[5] = 13cf12001
(XEN) context = ffff83013cf12000
(XEN) context[40] = 0_0
(XEN) ctxt_entry[40] not present
(XEN) [VT-D]iommu.c:821: iommu_fault_status: Primary Pending Fault
(XEN) [VT-D]iommu.c:796: DMAR:[DMA Write] Request device [05:08.0] fault
addr 2074be000, iommu reg = ffff82c3fff57000
(XEN) DMAR:[fault reason 02h] Present bit in context entry is clear
(XEN) print_vtd_entries: iommu = ffff83013fffaee0 bdf = 5:8.0 gmfn 2074be
(XEN) root_entry = ffff83013ff37000
(XEN) root_entry[5] = 13cf12001
(XEN) context = ffff83013cf12000
(XEN) context[40] = 0_0
(XEN) ctxt_entry[40] not present
(XEN) context[40] = 0_0
(XEN) ctxt_entry[40] not present
(XEN) [VT-D]iommu.c:796: DMAR:[DMA Write] Request device [05:08.0] fault
addr 204865000, iommu reg = ffff82c3fff57000
(XEN) DMAR:[fault reason 02h] Present bit in context entry is clear
(XEN) print_vtd_entries: iommu = ffff83013fffaee0 bdf = 5:8.0 gmfn 204865
(XEN) root_entry = ffff83013ff37000
(XEN) root_entry[5] = 13cf12001
(XEN) context = ffff83013cf12000
(XEN) context[40] = 0_0
(XEN) ctxt_entry[40] not present
(XEN) [VT-D]iommu.c:821: iommu_fault_status: Primary Pending Fault
(XEN) [VT-D]iommu.c:796: DMAR:[DMA Write] Request device [05:08.0] fault
addr 2074be000, iommu reg = ffff82c3fff57000
(XEN) DMAR:[fault reason 02h] Present bit in context entry is clear
(XEN) print_vtd_entries: iommu = ffff83013fffaee0 bdf = 5:8.0 gmfn 2074be
(XEN) root_entry = ffff83013ff37000
(XEN) root_entry[5] = 13cf12001
(XEN) context = ffff83013cf12000
(XEN) context[40] = 0_0
(XEN) ctxt_entry[40] not present
(XEN) context[40] = 0_0
(XEN) ctxt_entry[40] not present
(XEN) [VT-D]iommu.c:796: DMAR:[DMA Write] Request device [05:08.0] fault
addr 204865000, iommu reg = ffff82c3fff57000
(XEN) DMAR:[fault reason 02h] Present bit in context entry is clear
(XEN) print_vtd_entries: iommu = ffff83013fffaee0 bdf = 5:8.0 gmfn 204865
(XEN) root_entry = ffff83013ff37000
(XEN) root_entry[5] = 13cf12001
(XEN) context = ffff83013cf12000
(XEN) context[40] = 0_0
(XEN) ctxt_entry[40] not present
(XEN) [VT-D]iommu.c:821: iommu_fault_status: Primary Pending Fault
(XEN) [VT-D]iommu.c:796: DMAR:[DMA Write] Request device [05:08.0] fault
addr 2074be000, iommu reg = ffff82c3fff57000
(XEN) DMAR:[fault reason 02h] Present bit in context entry is clear
(XEN) print_vtd_entries: iommu = ffff83013fffaee0 bdf = 5:8.0 gmfn 2074be
(XEN) root_entry = ffff83013ff37000
(XEN) root_entry[5] = 13cf12001
(XEN) context = ffff83013cf12000
(XEN) context[40] = 0_0
(XEN) ctxt_entry[40] not present
_______________________________________________
Xen-devel mailing list
Xen-devel@lists.xensource.com
http://lists.xensource.com/xen-devel
Pasi Kärkkäinen
2010-May-29 15:20 UTC
Re: [Xen-devel] iommuu/vt-d issues with LSI MegaSAS (PERC5i)
On Sat, May 29, 2010 at 07:31:17AM -0700, M. Nunberg wrote:> I''ve been trying to get VT-D working wiht xen for quite some time, since > 3.4.2, and I''ve always had issues with my RAID controller not working > properly when iommu is not disabled in Xen: > > lspci outpuut for the card:<snip>> > I am using a Supermicro X8DALi motherboard with a 5500 chipset. > > Whenever I try to access the device the Xen console spits out something > like this: > (XEN) [VT-D]iommu.c:796: DMAR:[DMA Write] Request device [05:08.0] fault > addr 204865000, iommu reg = ffff82c3fff57000 > (XEN) DMAR:[fault reason 02h] Present bit in context entry is clear > (XEN) print_vtd_entries: iommu = ffff83013fffaee0 bdf = 5:8.0 gmfn > 204865 > (XEN) root_entry = ffff83013ff37000 > (XEN) root_entry[5] = 13cf12001 > (XEN) context = ffff83013cf12000 > (XEN) context[40] = 0_0 > (XEN) ctxt_entry[40] not present > (XEN) [VT-D]iommu.c:821: iommu_fault_status: Primary Pending Fault > > reads are partially succcessful, but I am getting seek errors at times, > filesystems will mount properly but I cannot use any of them properly.. > > > The actual kernel output varies, sometimes i get EINVAL when I try to > read from the filesystem, sometimes it simply refuses to at all > recognize the disk altogether, and other times it will hang the entire > system, including the hypervisor itself. > I''ve tried booting the hypervisor with x2apic disabled, but to no > effect. I''ve also tried with the latest xen-4.0-testing (4.0.1), buut > same issue and same outpuut > > A quick google turns up a thread, from this mailing list, with a > different RAID card, but the kernel output is similar.. e.g. > > scsi scan: INQUIRY result too short (5), using 36 > > http://lists.xensource.com/archives/html/xen-users/2010-04/msg00535.html > > The full xen log is below >Did you use the latest pvops dom0 kernel from xen/stable-2.6.32.x branch? Could you also post the full serial log _with_ the dom0 kernel messages? .. since the problem gets triggered by the dom0 kernel.. -- Pasi> > > L __ __ _ _ ___ > ___ > \ \/ /___ _ __ | || | / _ \ / _ \ 0x146000>, shtab=0x3a2078, > entry=0x100000 > \ // _ \ ''_ \ | || |_| | | | | | > | > / \ __/ | | | |__ _| |_| | |_| |apper/OS-root ro nomodeset > console=tty0 r > /_/\_\___|_| |_| | > _|(_)___(_)___/ > 020 > bytes] > (XEN) Xen version 4.0.0 (mordy@) (gcc version 4.3.2 (Debian 4.3.2-1.1) ) > Fri May 21 07:50:16 PDT 2010boot-module > @ > (XEN) Latest ChangeSet: > unavailable > (XEN) Console output is > synchronous. > (XEN) Command line: iommu=verbose loglvl=all guest_loglvl=all > sync_console console_to_rint com1=115200,8n1 > console=com1 > (XEN) Video > information: > (XEN) VGA is text mode 80x25, font > 8x16 > (XEN) VBE/DDC methods: none; EDID transfer time: 0 > seconds > (XEN) EDID info not retrieved because no DDC retrieval method > detected > (XEN) Disc information: > (XEN) Found 1 MBR signatures > (XEN) Found 1 EDD information structures > (XEN) Xen-e820 RAM map: > (XEN) 0000000000000000 - 000000000009a000 (usable) > (XEN) 000000000009a000 - 00000000000a0000 (reserved) > (XEN) 00000000000e0000 - 0000000000100000 (reserved) > (XEN) 0000000000100000 - 00000000bf760000 (usable) > (XEN) 00000000bf76e000 - 00000000bf770000 type 9 > (XEN) 00000000bf770000 - 00000000bf77e000 (ACPI data) > (XEN) 00000000bf77e000 - 00000000bf7d0000 (ACPI NVS) > (XEN) 00000000bf7d0000 - 00000000bf7e0000 (reserved) > (XEN) 00000000bf7ec000 - 00000000c0000000 (reserved) > (XEN) 00000000fee00000 - 00000000fee01000 (reserved) > (XEN) 00000000ffc00000 - 0000000100000000 (reserved) > (XEN) 0000000100000000 - 0000000340000000 (usable) > (XEN) ACPI: RSDP 000F9E10, 0024 (r2 ACPIAM) > (XEN) ACPI: XSDT BF770100, 0094 (r1 NEC 20090424 MSFT > 97) > (XEN) ACPI: FACP BF770290, 00F4 (r4 042409 FACP1917 20090424 MSFT > 97) > (XEN) ACPI: DSDT BF770670, 5BFB (r2 10601 10601000 0 INTL > 20051117) > (XEN) ACPI: FACS BF77E000, 0040 > (XEN) ACPI: APIC BF770390, 00D2 (r2 042409 APIC1917 20090424 MSFT > 97) > (XEN) ACPI: MCFG BF770470, 003C (r1 042409 OEMMCFG 20090424 MSFT > 97) > (XEN) ACPI: SLIC BF7704B0, 0176 (r1 NEC 20090424 MSFT > 97) > (XEN) ACPI: ERST BF770630, 0040 (r1 042409 WHEA1917 20090424 MSFT > 97) > (XEN) ACPI: OEMB BF77E040, 007B (r1 042409 OEMB1917 20090424 MSFT > 97) > (XEN) ACPI: SRAT BF77A670, 01D0 (r1 042409 OEMSRAT 1 INTL > 1) > (XEN) ACPI: HPET BF77A840, 0038 (r1 042409 OEMHPET 20090424 MSFT > 97) > (XEN) ACPI: DMAR BF77E0C0, 0118 (r1 AMI OEMDMAR 1 MSFT > 97) > (XEN) ACPI: SSDT BF781DF0, 0363 (r1 DpgPmm CpuPm 12 INTL > 20051117) > (XEN) ACPI: EINJ BF77A880, 0130 (r1 AMIER AMI_EINJ 20090424 MSFT > 97) > (XEN) ACPI: BERT BF77AA10, 0030 (r1 AMIER AMI_BERT 20090424 MSFT > 97) > (XEN) ACPI: ERST BF77AA40, 01B0 (r1 AMIER AMI_ERST 20090424 MSFT > 97) > (XEN) ACPI: HEST BF77ABF0, 00A8 (r1 AMIER AMI_HEST 20090424 MSFT > 97) > (XEN) System RAM: 12045MB (12334808kB) > (XEN) SRAT: PXM 0 -> APIC 0 -> Node 0 > (XEN) SRAT: PXM 0 -> APIC 2 -> Node 0 > (XEN) SRAT: PXM 0 -> APIC 4 -> Node 0 > (XEN) SRAT: PXM 0 -> APIC 6 -> Node 0 > (XEN) SRAT: PXM 0 -> APIC 1 -> Node 0 > (XEN) SRAT: PXM 0 -> APIC 3 -> Node 0 > (XEN) SRAT: PXM 0 -> APIC 5 -> Node 0 > (XEN) SRAT: PXM 0 -> APIC 7 -> Node 0 > (XEN) SRAT: PXM 1 -> APIC 16 -> Node 1 > (XEN) SRAT: PXM 1 -> APIC 18 -> Node 1 > (XEN) SRAT: PXM 1 -> APIC 20 -> Node 1 > (XEN) SRAT: PXM 1 -> APIC 22 -> Node 1 > (XEN) SRAT: PXM 1 -> APIC 17 -> Node 1 > (XEN) SRAT: PXM 1 -> APIC 19 -> Node 1 > (XEN) SRAT: PXM 1 -> APIC 21 -> Node 1 > (XEN) SRAT: PXM 1 -> APIC 23 -> Node 1 > (XEN) SRAT: Node 0 PXM 0 0-a0000 > (XEN) SRAT: Node 0 PXM 0 100000-c0000000 > (XEN) SRAT: Node 0 PXM 0 100000000-1c0000000 > (XEN) SRAT: Node 1 PXM 1 1c0000000-340000000 > (XEN) NUMA: Allocated memnodemap from 33fdfb000 - 33fdff000 > (XEN) NUMA: Using 8 for the hash shift. > (XEN) Domain heap initialised DMA width 30 bits > (XEN) found SMP MP-table at 000ff780 > (XEN) DMI present. > (XEN) Using APIC driver default > (XEN) ACPI: PM-Timer IO Port: 0x808 > (XEN) ACPI: ACPI SLEEP INFO: pm1x_cnt[804,0], pm1x_evt[800,0] > (XEN) ACPI: wakeup_vec[bf77e00c], vec_size[20] > (XEN) ACPI: Local APIC address 0xfee00000 > (XEN) ACPI: LAPIC (acpi_id[0x01] lapic_id[0x00] enabled) > (XEN) Processor #0 7:10 APIC version 21 > (XEN) ACPI: LAPIC (acpi_id[0x02] lapic_id[0x10] enabled) > (XEN) Processor #16 7:10 APIC version 21 > (XEN) ACPI: LAPIC (acpi_id[0x03] lapic_id[0x02] enabled) > (XEN) Processor #2 7:10 APIC version 21 > (XEN) ACPI: LAPIC (acpi_id[0x04] lapic_id[0x12] enabled) > (XEN) Processor #18 7:10 APIC version 21 > (XEN) ACPI: LAPIC (acpi_id[0x05] lapic_id[0x04] enabled) > (XEN) Processor #4 7:10 APIC version 21 > (XEN) ACPI: LAPIC (acpi_id[0x06] lapic_id[0x14] enabled) > (XEN) Processor #20 7:10 APIC version 21 > (XEN) ACPI: LAPIC (acpi_id[0x07] lapic_id[0x06] enabled) > (XEN) Processor #6 7:10 APIC version 21 > (XEN) ACPI: LAPIC (acpi_id[0x08] lapic_id[0x16] enabled) > (XEN) Processor #22 7:10 APIC version 21 > (XEN) ACPI: LAPIC (acpi_id[0x09] lapic_id[0x01] enabled) > (XEN) Processor #1 7:10 APIC version 21 > (XEN) ACPI: LAPIC (acpi_id[0x0a] lapic_id[0x11] enabled) > (XEN) Processor #17 7:10 APIC version 21 > (XEN) ACPI: LAPIC (acpi_id[0x0b] lapic_id[0x03] enabled) > (XEN) Processor #3 7:10 APIC version 21 > (XEN) ACPI: LAPIC (acpi_id[0x0c] lapic_id[0x13] enabled) > (XEN) Processor #19 7:10 APIC version 21 > (XEN) ACPI: LAPIC (acpi_id[0x0d] lapic_id[0x05] enabled) > (XEN) Processor #5 7:10 APIC version 21 > (XEN) ACPI: LAPIC (acpi_id[0x0e] lapic_id[0x15] enabled) > (XEN) Processor #21 7:10 APIC version 21 > (XEN) ACPI: LAPIC (acpi_id[0x0f] lapic_id[0x07] enabled) > (XEN) Processor #7 7:10 APIC version 21 > (XEN) ACPI: LAPIC (acpi_id[0x10] lapic_id[0x17] enabled) > (XEN) Processor #23 7:10 APIC version 21 > (XEN) ACPI: LAPIC_NMI (acpi_id[0xff] dfl dfl lint[0x1]) > (XEN) Overriding APIC driver with bigsmp > (XEN) ACPI: IOAPIC (id[0x08] address[0xfec00000] gsi_base[0]) > (XEN) IOAPIC[0]: apic_id 8, version 32, address 0xfec00000, GSI 0-23 > (XEN) ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl) > (XEN) ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 20 low level) > (XEN) ACPI: IRQ0 used by override. > (XEN) ACPI: IRQ2 used by override. > (XEN) ACPI: IRQ9 used by override. > (XEN) Enabling APIC mode: Phys. Using 1 I/O APICs > (XEN) ACPI: HPET id: 0xffffffff base: 0xfed00000 > (XEN) [VT-D]dmar.c:679: Host address width 40 > (XEN) [VT-D]dmar.c:694: found ACPI_DMAR_DRHD: > (XEN) [VT-D]dmar.c:398: dmaru->address = fbffe000 > (XEN) [VT-D]dmar.c:340: IOAPIC: f0:1f.7 > (XEN) [VT-D]dmar.c:411: flags: INCLUDE_ALL > (XEN) [VT-D]dmar.c:699: found ACPI_DMAR_RMRR: > (XEN) [VT-D]dmar.c:334: endpoint: 0:1d.0 > (XEN) [VT-D]dmar.c:334: endpoint: 0:1d.1 > (XEN) [VT-D]dmar.c:334: endpoint: 0:1d.2 > (XEN) [VT-D]dmar.c:334: endpoint: 0:1d.7 > (XEN) [VT-D]dmar.c:334: endpoint: 0:1a.0 > (XEN) [VT-D]dmar.c:334: endpoint: 0:1a.1 > (XEN) [VT-D]dmar.c:334: endpoint: 0:1a.2 > (XEN) [VT-D]dmar.c:334: endpoint: 0:1a.7 > (XEN) [VT-D]dmar.c:571: RMRR region: base_addr ec000 end_address effff > (XEN) [VT-D]dmar.c:699: found ACPI_DMAR_RMRR: > (XEN) [VT-D]dmar.c:334: endpoint: 0:1d.0 > (XEN) [VT-D]dmar.c:334: endpoint: 0:1d.1 > (XEN) [VT-D]dmar.c:334: endpoint: 0:1d.2 > (XEN) [VT-D]dmar.c:334: endpoint: 0:1d.7 > (XEN) [VT-D]dmar.c:334: endpoint: 0:1a.0 > (XEN) [VT-D]dmar.c:334: endpoint: 0:1a.1 > (XEN) [VT-D]dmar.c:334: endpoint: 0:1a.2 > (XEN) [VT-D]dmar.c:334: endpoint: 0:1a.7 > (XEN) [VT-D]dmar.c:571: RMRR region: base_addr bf7ec000 end_address > bf7fffff > (XEN) [VT-D]dmar.c:704: found ACPI_DMAR_ATSR: > (XEN) [VT-D]dmar.c:599: atsru->all_ports: 0 > (XEN) [VT-D]dmar.c:320: bridge: 0:1.0 start = 0 sec = 1 sub = 1 > (XEN) [VT-D]dmar.c:320: bridge: 0:3.0 start = 0 sec = 2 sub = 2 > (XEN) [VT-D]dmar.c:320: bridge: 0:7.0 start = 0 sec = 3 sub = 3 > (XEN) PCI: MCFG configuration 0: base e0000000 segment 0 buses 0 - 255 > (XEN) PCI: Not using MMCONFIG. > (XEN) Using ACPI (MADT) for SMP configuration information > (XEN) Using scheduler: SMP Credit Scheduler (credit) > (XEN) Detected 2266.790 MHz processor. > (XEN) Initing memory sharing. > (XEN) VMX: Supported advanced features: > (XEN) - APIC MMIO access virtualisation > (XEN) - APIC TPR shadow > (XEN) - Extended Page Tables (EPT) > (XEN) - Virtual-Processor Identifiers (VPID) > (XEN) - Virtual NMI > (XEN) - MSR direct-access bitmap > (XEN) HVM: ASIDs enabled. > (XEN) HVM: VMX enabled > (XEN) HVM: Hardware Assisted Paging detected. > (XEN) Intel machine check reporting enabled > (XEN) [VT-D]iommu.c:1078: drhd->address = fbffe000 iommu->reg > ffff82c3fff57000 > (XEN) [VT-D]iommu.c:1080: cap = c90780106f0462 ecap = f0207e > (XEN) Intel VT-d Snoop Control not supported. > (XEN) Intel VT-d DMA Passthrough not supported. > (XEN) Intel VT-d Queued Invalidation supported. > (XEN) Intel VT-d Interrupt Remapping supported. > (XEN) I/O virtualisation enabled > (XEN) I/O virtualisation for PV guests disabled > (XEN) Total of 16 processors activated. > (XEN) ENABLING IO-APIC IRQs > (XEN) -> Using new ACK method > (XEN) ..TIMER: vector=0xF0 apic1=0 pin1=2 apic2=-1 pin2=-1 > (XEN) TSC is reliable, synchronization unnecessary > (XEN) Platform timer is 14.318MHz HPET > ?(XEN) Allocated console ring of 128 KiB. > (XEN) microcode.c:73:d32767 microcode: CPU1 resumed > (XEN) microcode.c:73:d32767 microcode: CPU9 resumed > (XEN) microcode.c:73:d32767 microcode: CPU14 resumed > (XEN) microcode.c:73:d32767 microcode: CPU6 resumed > (XEN) microcode.c:73:d32767 microcode: CPU3 resumed > (XEN) microcode.c:73:d32767 microcode: CPU11 resumed > (XEN) microcode.c:73:d32767 microcode: CPU8 resumed > (XEN) microcode.c:73:d32767 microcode: CPU7 resumed > (XEN) microcode.c:73:d32767 microcode: CPU15 resumed > (XEN) microcode.c:73:d32767 microcode: CPU2 resumed > (XEN) microcode.c:73:d32767 microcode: CPU5 resumed > (XEN) microcode.c:73:d32767 microcode: CPU13 resumed > (XEN) microcode.c:73:d32767 microcode: CPU4 resumed > (XEN) microcode.c:73:d32767 microcode: CPU10 resumed > (XEN) Brought up 16 CPUs > (XEN) microcode.c:73:d32767 microcode: CPU12 resumed > (XEN) Turbo Mode detected! > (XEN) HPET''s MSI mode hasn''t been supported when Interrupt Remapping is > enabled. > (XEN) ACPI sleep modes: S3 > (XEN) mcheck_poll: Machine check polling timer started. > (XEN) [VT-D]iommu.c:1325: d0:PCIe: map bdf = 0:0.0 > (XEN) [VT-D]iommu.c:1325: d0:PCIe: map bdf = 0:14.0 > (XEN) [VT-D]iommu.c:1325: d0:PCIe: map bdf = 0:14.1 > (XEN) [VT-D]iommu.c:1325: d0:PCIe: map bdf = 0:14.2 > (XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = 0:14.3 > (XEN) [VT-D]iommu.c:1325: d0:PCIe: map bdf = 0:16.0 > (XEN) [VT-D]iommu.c:1325: d0:PCIe: map bdf = 0:16.1 > (XEN) [VT-D]iommu.c:1325: d0:PCIe: map bdf = 0:16.2 > (XEN) [VT-D]iommu.c:1325: d0:PCIe: map bdf = 0:16.3 > (XEN) [VT-D]iommu.c:1325: d0:PCIe: map bdf = 0:16.4 > (XEN) [VT-D]iommu.c:1325: d0:PCIe: map bdf = 0:16.5 > (XEN) [VT-D]iommu.c:1325: d0:PCIe: map bdf = 0:16.6 > (XEN) [VT-D]iommu.c:1325: d0:PCIe: map bdf = 0:16.7 > (XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = 0:1a.0 > (XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = 0:1a.1 > (XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = 0:1a.2 > (XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = 0:1a.7 > (XEN) [VT-D]iommu.c:1325: d0:PCIe: map bdf = 0:1b.0 > (XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = 0:1d.0 > (XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = 0:1d.1 > (XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = 0:1d.2 > (XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = 0:1d.7 > (XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = 0:1f.0 > (XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = 0:1f.2 > (XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = 0:1f.3 > (XEN) [VT-D]iommu.c:1325: d0:PCIe: map bdf = 1:0.0 > (XEN) [VT-D]iommu.c:1325: d0:PCIe: map bdf = 3:0.0 > (XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = 5:e.0 > (XEN) [VT-D]iommu.c:1325: d0:PCIe: map bdf = 7:0.0 > (XEN) [VT-D]iommu.c:1325: d0:PCIe: map bdf = 8:0.0 > (XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = fe:0.0 > (XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = fe:0.1 > (XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = fe:2.0 > (XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = fe:2.1 > (XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = fe:2.4 > (XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = fe:2.5 > (XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = fe:3.0 > (XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = fe:3.1 > (XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = fe:3.2 > (XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = fe:3.4 > (XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = fe:4.0 > (XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = fe:4.1 > (XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = fe:4.2 > (XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = fe:4.3 > (XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = fe:5.0 > (XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = fe:5.1 > (XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = fe:5.2 > (XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = fe:5.3 > (XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = fe:6.0 > (XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = fe:6.1 > (XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = fe:6.2 > (XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = fe:6.3 > (XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = ff:0.0 > (XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = ff:0.1 > (XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = ff:2.0 > (XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = ff:2.1 > (XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = ff:2.4 > (XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = ff:2.5 > (XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = ff:3.0 > (XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = ff:3.1 > (XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = ff:3.2 > (XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = ff:3.4 > (XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = ff:4.0 > (XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = ff:4.1 > (XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = ff:4.2 > (XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = ff:4.3 > (XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = ff:5.0 > (XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = ff:5.1 > (XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = ff:5.2 > (XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = ff:5.3 > (XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = ff:6.0 > (XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = ff:6.1 > (XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = ff:6.2 > (XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = ff:6.3 > (XEN) [VT-D]iommu.c:695: iommu_enable_translation: iommu->reg > ffff82c3fff57000 > (XEN) *** LOADING DOMAIN 0 *** > (XEN) Xen kernel: 64-bit, lsb, compat32 > (XEN) Dom0 kernel: 64-bit, PAE, lsb, paddr 0x1000000 -> 0x26b6000 > (XEN) PHYSICAL MEMORY ARRANGEMENT: > (XEN) Dom0 alloc.: 0000000100000000->0000000120000000 (2937045 pages > to be allocated) > (XEN) VIRTUAL MEMORY ARRANGEMENT: > (XEN) Loaded kernel: ffffffff81000000->ffffffff826b6000 > (XEN) Init. ramdisk: ffffffff826b6000->ffffffff8f7d7600 > (XEN) Phys-Mach map: ffffffff8f7d8000->ffffffff90f406a8 > (XEN) Start info: ffffffff90f41000->ffffffff90f414b4 > (XEN) Page tables: ffffffff90f42000->ffffffff90fcf000 > (XEN) Boot stack: ffffffff90fcf000->ffffffff90fd0000 > (XEN) TOTAL: ffffffff80000000->ffffffff91400000 > (XEN) ENTRY ADDRESS: ffffffff819be200 > (XEN) Dom0 has maximum 16 VCPUs > (XEN) Scrubbing Free RAM: .done. > (XEN) Xen trace buffers: disabled > (XEN) Std. Loglevel: All > (XEN) Guest Loglevel: All > (XEN) ********************************************** > (XEN) ******* WARNING: CONSOLE OUTPUT IS SYNCHRONOUS > (XEN) ******* This option is intended to aid debugging of Xen by > ensuring > (XEN) ******* that all output is synchronously delivered on the serial > line. > (XEN) ******* However it can introduce SIGNIFICANT latencies and affect > (XEN) ******* timekeeping. It is NOT recommended for production use! > (XEN) ********************************************** > (XEN) 3... 2... 1... > (XEN) *** Serial input -> DOM0 (type ''CTRL-a'' three times to switch > input to Xen) > (XEN) Freed 164kB init memory. > mapping kernel into physical memory > Xen: setup ISA identity maps > about to get started... > (XEN) PCI add device 00:00.0 > (XEN) PCI add device 00:01.0 > (XEN) PCI add device 00:03.0 > (XEN) PCI add device 00:07.0 > (XEN) PCI add device 00:14.0 > (XEN) PCI add device 00:14.1 > (XEN) PCI add device 00:14.2 > (XEN) PCI add device 00:14.3 > (XEN) PCI add device 00:16.0 > (XEN) PCI add device 00:16.1 > (XEN) PCI add device 00:16.2 > (XEN) PCI add device 00:16.3 > (XEN) PCI add device 00:16.4 > (XEN) PCI add device 00:16.5 > (XEN) PCI add device 00:16.6 > (XEN) PCI add device 00:16.7 > (XEN) PCI add device 00:1a.0 > (XEN) PCI add device 00:1a.1 > (XEN) PCI add device 00:1a.2 > (XEN) PCI add device 00:1a.7 > (XEN) PCI add device 00:1b.0 > (XEN) PCI add device 00:1c.0 > (XEN) PCI add device 00:1c.4 > (XEN) PCI add device 00:1c.5 > (XEN) PCI add device 00:1d.0 > (XEN) PCI add device 00:1d.1 > (XEN) PCI add device 00:1d.2 > (XEN) PCI add device 00:1d.7 > (XEN) PCI add device 00:1e.0 > (XEN) PCI add device 00:1f.0 > (XEN) PCI add device 00:1f.2 > (XEN) PCI add device 00:1f.3 > (XEN) PCI add device 01:00.0 > (XEN) PCI add device 03:00.0 > (XEN) PCI add device 04:00.0 > (XEN) PCI add device 04:00.2 > (XEN) PCI add device 05:0e.0 > (XEN) PCI add device 07:00.0 > (XEN) PCI add device 08:00.0 > (XEN) cpuid.MWAIT[.eax=40, .ebx=40, .ecx=3, .edx=1120] > (XEN) Monitor-Mwait will be used to enter C-1 state > (XEN) cpuid.MWAIT[.eax=40, .ebx=40, .ecx=3, .edx=1120] > (XEN) Monitor-Mwait will be used to enter C-3 state > (XEN) cpuid.MWAIT[.eax=40, .ebx=40, .ecx=3, .edx=1120] > (XEN) Monitor-Mwait will be used to enter C-3 state > (XEN) cpuid.MWAIT[.eax=40, .ebx=40, .ecx=3, .edx=1120] > (XEN) Monitor-Mwait will be used to enter C-1 state > (XEN) cpuid.MWAIT[.eax=40, .ebx=40, .ecx=3, .edx=1120] > (XEN) Monitor-Mwait will be used to enter C-3 state > (XEN) cpuid.MWAIT[.eax=40, .ebx=40, .ecx=3, .edx=1120] > (XEN) Monitor-Mwait will be used to enter C-3 state > (XEN) cpuid.MWAIT[.eax=40, .ebx=40, .ecx=3, .edx=1120] > (XEN) Monitor-Mwait will be used to enter C-1 state > (XEN) cpuid.MWAIT[.eax=40, .ebx=40, .ecx=3, .edx=1120] > (XEN) Monitor-Mwait will be used to enter C-3 state > (XEN) cpuid.MWAIT[.eax=40, .ebx=40, .ecx=3, .edx=1120] > (XEN) Monitor-Mwait will be used to enter C-3 state > (XEN) cpuid.MWAIT[.eax=40, .ebx=40, .ecx=3, .edx=1120] > (XEN) Monitor-Mwait will be used to enter C-1 state > (XEN) cpuid.MWAIT[.eax=40, .ebx=40, .ecx=3, .edx=1120] > (XEN) Monitor-Mwait will be used to enter C-3 state > (XEN) cpuid.MWAIT[.eax=40, .ebx=40, .ecx=3, .edx=1120] > (XEN) Monitor-Mwait will be used to enter C-3 state > (XEN) cpuid.MWAIT[.eax=40, .ebx=40, .ecx=3, .edx=1120] > (XEN) Monitor-Mwait will be used to enter C-1 state > (XEN) cpuid.MWAIT[.eax=40, .ebx=40, .ecx=3, .edx=1120] > (XEN) Monitor-Mwait will be used to enter C-3 state > (XEN) cpuid.MWAIT[.eax=40, .ebx=40, .ecx=3, .edx=1120] > (XEN) Monitor-Mwait will be used to enter C-3 state > (XEN) cpuid.MWAIT[.eax=40, .ebx=40, .ecx=3, .edx=1120] > (XEN) Monitor-Mwait will be used to enter C-1 state > (XEN) cpuid.MWAIT[.eax=40, .ebx=40, .ecx=3, .edx=1120] > (XEN) Monitor-Mwait will be used to enter C-3 state > (XEN) cpuid.MWAIT[.eax=40, .ebx=40, .ecx=3, .edx=1120] > (XEN) Monitor-Mwait will be used to enter C-3 state > (XEN) cpuid.MWAIT[.eax=40, .ebx=40, .ecx=3, .edx=1120] > (XEN) Monitor-Mwait will be used to enter C-1 state > (XEN) cpuid.MWAIT[.eax=40, .ebx=40, .ecx=3, .edx=1120] > (XEN) Monitor-Mwait will be used to enter C-3 state > (XEN) cpuid.MWAIT[.eax=40, .ebx=40, .ecx=3, .edx=1120] > (XEN) Monitor-Mwait will be used to enter C-3 state > (XEN) cpuid.MWAIT[.eax=40, .ebx=40, .ecx=3, .edx=1120] > (XEN) Monitor-Mwait will be used to enter C-1 state > (XEN) cpuid.MWAIT[.eax=40, .ebx=40, .ecx=3, .edx=1120] > (XEN) Monitor-Mwait will be used to enter C-3 state > (XEN) cpuid.MWAIT[.eax=40, .ebx=40, .ecx=3, .edx=1120] > (XEN) Monitor-Mwait will be used to enter C-3 state > (XEN) cpuid.MWAIT[.eax=40, .ebx=40, .ecx=3, .edx=1120] > (XEN) Monitor-Mwait will be used to enter C-1 state > (XEN) cpuid.MWAIT[.eax=40, .ebx=40, .ecx=3, .edx=1120] > (XEN) Monitor-Mwait will be used to enter C-3 state > (XEN) cpuid.MWAIT[.eax=40, .ebx=40, .ecx=3, .edx=1120] > (XEN) Monitor-Mwait will be used to enter C-3 state > (XEN) cpuid.MWAIT[.eax=40, .ebx=40, .ecx=3, .edx=1120] > (XEN) Monitor-Mwait will be used to enter C-1 state > (XEN) cpuid.MWAIT[.eax=40, .ebx=40, .ecx=3, .edx=1120] > (XEN) Monitor-Mwait will be used to enter C-3 state > (XEN) cpuid.MWAIT[.eax=40, .ebx=40, .ecx=3, .edx=1120] > (XEN) Monitor-Mwait will be used to enter C-3 state > (XEN) cpuid.MWAIT[.eax=40, .ebx=40, .ecx=3, .edx=1120] > (XEN) Monitor-Mwait will be used to enter C-1 state > (XEN) cpuid.MWAIT[.eax=40, .ebx=40, .ecx=3, .edx=1120] > (XEN) Monitor-Mwait will be used to enter C-3 state > (XEN) cpuid.MWAIT[.eax=40, .ebx=40, .ecx=3, .edx=1120] > (XEN) Monitor-Mwait will be used to enter C-3 state > (XEN) cpuid.MWAIT[.eax=40, .ebx=40, .ecx=3, .edx=1120] > (XEN) Monitor-Mwait will be used to enter C-1 state > (XEN) cpuid.MWAIT[.eax=40, .ebx=40, .ecx=3, .edx=1120] > (XEN) Monitor-Mwait will be used to enter C-3 state > (XEN) cpuid.MWAIT[.eax=40, .ebx=40, .ecx=3, .edx=1120] > (XEN) Monitor-Mwait will be used to enter C-3 state > (XEN) cpuid.MWAIT[.eax=40, .ebx=40, .ecx=3, .edx=1120] > (XEN) Monitor-Mwait will be used to enter C-1 state > (XEN) cpuid.MWAIT[.eax=40, .ebx=40, .ecx=3, .edx=1120] > (XEN) Monitor-Mwait will be used to enter C-3 state > (XEN) cpuid.MWAIT[.eax=40, .ebx=40, .ecx=3, .edx=1120] > (XEN) Monitor-Mwait will be used to enter C-3 state > (XEN) cpuid.MWAIT[.eax=40, .ebx=40, .ecx=3, .edx=1120] > (XEN) Monitor-Mwait will be used to enter C-1 state > (XEN) cpuid.MWAIT[.eax=40, .ebx=40, .ecx=3, .edx=1120] > (XEN) Monitor-Mwait will be used to enter C-3 state > (XEN) cpuid.MWAIT[.eax=40, .ebx=40, .ecx=3, .edx=1120] > (XEN) Monitor-Mwait will be used to enter C-3 state > (XEN) cpuid.MWAIT[.eax=40, .ebx=40, .ecx=3, .edx=1120] > (XEN) Monitor-Mwait will be used to enter C-1 state > (XEN) cpuid.MWAIT[.eax=40, .ebx=40, .ecx=3, .edx=1120] > (XEN) Monitor-Mwait will be used to enter C-3 state > (XEN) cpuid.MWAIT[.eax=40, .ebx=40, .ecx=3, .edx=1120] > (XEN) Monitor-Mwait will be used to enter C-3 state > (XEN) cpuid.MWAIT[.eax=40, .ebx=40, .ecx=3, .edx=1120] > (XEN) Monitor-Mwait will be used to enter C-1 state > (XEN) cpuid.MWAIT[.eax=40, .ebx=40, .ecx=3, .edx=1120] > (XEN) Monitor-Mwait will be used to enter C-3 state > (XEN) cpuid.MWAIT[.eax=40, .ebx=40, .ecx=3, .edx=1120] > (XEN) Monitor-Mwait will be used to enter C-3 state > (XEN) irq.c:1139:d0 Cannot bind IRQ 4 to guest. In use by ''ns16550''. > (XEN) irq.c:1139:d0 Cannot bind IRQ 2 to guest. In use by ''cascade''. > (XEN) irq.c:1139:d0 Cannot bind IRQ 4 to guest. In use by ''ns16550''. > (XEN) irq.c:1139:d0 Cannot bind IRQ 2 to guest. In use by ''cascade''. > (XEN) irq.c:1139:d0 Cannot bind IRQ 4 to guest. In use by ''ns16550''. > (XEN) irq.c:1139:d0 Cannot bind IRQ 2 to guest. In use by ''cascade''. > (XEN) irq.c:1139:d0 Cannot bind IRQ 4 to guest. In use by ''ns16550''. > (XEN) irq.c:1139:d0 Cannot bind IRQ 2 to guest. In use by ''cascade''. > (XEN) [VT-D]iommu.c:821: iommu_fault_status: Primary Pending Fault > (XEN) [VT-D]iommu.c:796: DMAR:[DMA Write] Request device [05:08.0] fault > addr 203a09000, iommu reg = ffff82c3fff57000 > (XEN) DMAR:[fault reason 02h] Present bit in context entry is clear > (XEN) print_vtd_entries: iommu = ffff83013fffaee0 bdf = 5:8.0 gmfn > 203a09 > (XEN) root_entry = ffff83013ff37000 > (XEN) root_entry[5] = 13cf12001 > (XEN) context = ffff83013cf12000 > (XEN) context[40] = 0_0 > (XEN) ctxt_entry[40] not present > (XEN) [VT-D]iommu.c:796: DMAR:[DMA Write] Request device [05:08.0] fault > addr 203eba000, iommu reg = ffff82c3fff57000 > (XEN) DMAR:[fault reason 02h] Present bit in context entry is clear > (XEN) print_vtd_entries: iommu = ffff83013fffaee0 bdf = 5:8.0 gmfn > 203eba > (XEN) root_entry = ffff83013ff37000 > (XEN) root_entry[5] = 13cf12001 > (XEN) context = ffff83013cf12000 > (XEN) context[40] = 0_0 > (XEN) ctxt_entry[40] not present > (XEN) [VT-D]iommu.c:821: iommu_fault_status: Primary Pending Fault > (XEN) [VT-D]iommu.c:796: DMAR:[DMA Write] Request device [05:08.0] fault > addr 204e11000, iommu reg = ffff82c3fff57000 > (XEN) DMAR:[fault reason 02h] Present bit in context entry is clear > (XEN) print_vtd_entries: iommu = ffff83013fffaee0 bdf = 5:8.0 gmfn > 204e11 > (XEN) root_entry = ffff83013ff37000 > (XEN) root_entry[5] = 13cf12001 > (XEN) context = ffff83013cf12000 > (XEN) context[40] = 0_0 > (XEN) ctxt_entry[40] not present > (XEN) [VT-D]iommu.c:821: iommu_fault_status: Primary Pending Fault > (XEN) [VT-D]iommu.c:796: DMAR:[DMA Write] Request device [05:08.0] fault > addr 2061e2000, iommu reg = ffff82c3fff57000 > (XEN) DMAR:[fault reason 02h] Present bit in context entry is clear > (XEN) print_vtd_entries: iommu = ffff83013fffaee0 bdf = 5:8.0 gmfn > 2061e2 > (XEN) root_entry = ffff83013ff37000 > (XEN) root_entry[5] = 13cf12001 > (XEN) context = ffff83013cf12000 > (XEN) context[40] = 0_0 > (XEN) ctxt_entry[40] not present > (XEN) [VT-D]iommu.c:796: DMAR:[DMA Write] Request device [05:08.0] fault > addr 205043000, iommu reg = ffff82c3fff57000 > (XEN) DMAR:[fault reason 02h] Present bit in context entry is clear > (XEN) print_vtd_entries: iommu = ffff83013fffaee0 bdf = 5:8.0 gmfn > 205043 > (XEN) root_entry = ffff83013ff37000 > (XEN) root_entry[5] = 13cf12001 > (XEN) context = ffff83013cf12000 > (XEN) context[40] = 0_0 > (XEN) ctxt_entry[40] not present > (XEN) [VT-D]iommu.c:821: iommu_fault_status: Primary Pending Fault > (XEN) [VT-D]iommu.c:796: DMAR:[DMA Write] Request device [05:08.0] fault > addr 20552b000, iommu reg = ffff82c3fff57000 > (XEN) DMAR:[fault reason 02h] Present bit in context entry is clear > (XEN) print_vtd_entries: iommu = ffff83013fffaee0 bdf = 5:8.0 gmfn > 20552b > (XEN) root_entry = ffff83013ff37000 > (XEN) root_entry[5] = 13cf12001 > (XEN) context = ffff83013cf12000 > (XEN) context[40] = 0_0 > (XEN) ctxt_entry[40] not present > (XEN) [VT-D]iommu.c:821: iommu_fault_status: Primary Pending Fault > (XEN) [VT-D]iommu.c:796: DMAR:[DMA Write] Request device [05:08.0] fault > addr 205708000, iommu reg = ffff82c3fff57000 > (XEN) DMAR:[fault reason 02h] Present bit in context entry is clear > (XEN) print_vtd_entries: iommu = ffff83013fffaee0 bdf = 5:8.0 gmfn > 205708 > (XEN) root_entry = ffff83013ff37000 > (XEN) root_entry[5] = 13cf12001 > (XEN) context = ffff83013cf12000 > (XEN) context[40] = 0_0 > (XEN) ctxt_entry[40] not present > (XEN) [VT-D]iommu.c:796: DMAR:[DMA Write] Request device [05:08.0] fault > addr 2060c0000, iommu reg = ffff82c3fff57000 > (XEN) DMAR:[fault reason 02h] Present bit in context entry is clear > (XEN) print_vtd_entries: iommu = ffff83013fffaee0 bdf = 5:8.0 gmfn > 2060c0 > (XEN) root_entry = ffff83013ff37000 > (XEN) root_entry[5] = 13cf12001 > (XEN) context = ffff83013cf12000 > (XEN) context[40] = 0_0 > (XEN) ctxt_entry[40] not present > (XEN) [VT-D]iommu.c:821: iommu_fault_status: Primary Pending Fault > (XEN) [VT-D]iommu.c:796: DMAR:[DMA Write] Request device [05:08.0] fault > addr 206591000, iommu reg = ffff82c3fff57000 > (XEN) DMAR:[fault reason 02h] Present bit in context entry is clear > (XEN) print_vtd_entries: iommu = ffff83013fffaee0 bdf = 5:8.0 gmfn > 206591 > (XEN) root_entry = ffff83013ff37000 > (XEN) root_entry[5] = 13cf12001 > (XEN) context = ffff83013cf12000 > (XEN) context[40] = 0_0 > (XEN) ctxt_entry[40] not present > (XEN) [VT-D]iommu.c:796: DMAR:[DMA Write] Request device [05:08.0] fault > addr 204353000, iommu reg = ffff82c3fff57000 > (XEN) DMAR:[fault reason 02h] Present bit in context entry is clear > (XEN) print_vtd_entries: iommu = ffff83013fffaee0 bdf = 5:8.0 gmfn > 204353 > (XEN) root_entry = ffff83013ff37000 > (XEN) root_entry[5] = 13cf12001 > (XEN) context = ffff83013cf12000 > (XEN) context[40] = 0_0 > (XEN) ctxt_entry[40] not present > (XEN) [VT-D]iommu.c:821: iommu_fault_status: Primary Pending Fault > (XEN) [VT-D]iommu.c:796: DMAR:[DMA Write] Request device [05:08.0] fault > addr 2061f2000, iommu reg = ffff82c3fff57000 > (XEN) DMAR:[fault reason 02h] Present bit in context entry is clear > (XEN) print_vtd_entries: iommu = ffff83013fffaee0 bdf = 5:8.0 gmfn > 2061f2 > (XEN) root_entry = ffff83013ff37000 > (XEN) root_entry[5] = 13cf12001 > (XEN) context = ffff83013cf12000 > (XEN) context[40] = 0_0 > (XEN) ctxt_entry[40] not present > (XEN) [VT-D]iommu.c:796: DMAR:[DMA Write] Request device [05:08.0] fault > addr 204306000, iommu reg = ffff82c3fff57000 > (XEN) DMAR:[fault reason 02h] Present bit in context entry is clear > (XEN) print_vtd_entries: iommu = ffff83013fffaee0 bdf = 5:8.0 gmfn > 204306 > (XEN) root_entry = ffff83013ff37000 > (XEN) root_entry[5] = 13cf12001 > (XEN) context = ffff83013cf12000 > (XEN) context[40] = 0_0 > (XEN) ctxt_entry[40] not present > (XEN) [VT-D]iommu.c:821: iommu_fault_status: Primary Pending Fault > (XEN) [VT-D]iommu.c:796: DMAR:[DMA Write] Request device [05:08.0] fault > addr 205f6b000, iommu reg = ffff82c3fff57000 > (XEN) DMAR:[fault reason 02h] Present bit in context entry is clear > (XEN) print_vtd_entries: iommu = ffff83013fffaee0 bdf = 5:8.0 gmfn > 205f6b > (XEN) root_entry = ffff83013ff37000 > (XEN) root_entry[5] = 13cf12001 > (XEN) context = ffff83013cf12000 > (XEN) context[40] = 0_0 > (XEN) ctxt_entry[40] not present > (XEN) [VT-D]iommu.c:796: DMAR:[DMA Write] Request device [05:08.0] fault > addr 205665000, iommu reg = ffff82c3fff57000 > (XEN) DMAR:[fault reason 02h] Present bit in context entry is clear > (XEN) print_vtd_entries: iommu = ffff83013fffaee0 bdf = 5:8.0 gmfn > 205665 > (XEN) root_entry = ffff83013ff37000 > (XEN) root_entry[5] = 13cf12001 > (XEN) context = ffff83013cf12000 > (XEN) context[40] = 0_0 > (XEN) ctxt_entry[40] not present > (XEN) [VT-D]iommu.c:821: iommu_fault_status: Primary Pending Fault > (XEN) [VT-D]iommu.c:796: DMAR:[DMA Write] Request device [05:08.0] fault > addr 2045a0000, iommu reg = ffff82c3fff57000 > (XEN) DMAR:[fault reason 02h] Present bit in context entry is clear > (XEN) print_vtd_entries: iommu = ffff83013fffaee0 bdf = 5:8.0 gmfn > 2045a0 > (XEN) root_entry = ffff83013ff37000 > (XEN) root_entry[5] = 13cf12001 > (XEN) context = ffff83013cf12000 > (XEN) context[40] = 0_0 > (XEN) ctxt_entry[40] not present > (XEN) [VT-D]iommu.c:796: DMAR:[DMA Write] Request device [05:08.0] fault > addr 205669000, iommu reg = ffff82c3fff57000 > (XEN) DMAR:[fault reason 02h] Present bit in context entry is clear > (XEN) print_vtd_entries: iommu = ffff83013fffaee0 bdf = 5:8.0 gmfn > 205669 > (XEN) root_entry = ffff83013ff37000 > (XEN) root_entry[5] = 13cf12001 > (XEN) context = ffff83013cf12000 > (XEN) context[40] = 0_0 > (XEN) ctxt_entry[40] not present > (XEN) [VT-D]iommu.c:821: iommu_fault_status: Primary Pending Fault > (XEN) [VT-D]iommu.c:796: DMAR:[DMA Write] Request device [05:08.0] fault > addr 2042c6000, iommu reg = ffff82c3fff57000 > (XEN) DMAR:[fault reason 02h] Present bit in context entry is clear > (XEN) print_vtd_entries: iommu = ffff83013fffaee0 bdf = 5:8.0 gmfn > 2042c6 > (XEN) root_entry = ffff83013ff37000 > (XEN) root_entry[5] = 13cf12001 > (XEN) context = ffff83013cf12000 > (XEN) context[40] = 0_0 > (XEN) ctxt_entry[40] not present > (XEN) [VT-D]iommu.c:796: DMAR:[DMA Write] Request device [05:08.0] fault > addr 2061fe000, iommu reg = ffff82c3fff57000 > (XEN) DMAR:[fault reason 02h] Present bit in context entry is clear > (XEN) print_vtd_entries: iommu = ffff83013fffaee0 bdf = 5:8.0 gmfn > 2061fe > (XEN) root_entry = ffff83013ff37000 > (XEN) root_entry[5] = 13cf12001 > (XEN) context = ffff83013cf12000 > (XEN) context[40] = 0_0 > (XEN) ctxt_entry[40] not present > (XEN) [VT-D]iommu.c:821: iommu_fault_status: Primary Pending Fault > (XEN) [VT-D]iommu.c:796: DMAR:[DMA Write] Request device [05:08.0] fault > addr 20560a000, iommu reg = ffff82c3fff57000 > (XEN) DMAR:[fault reason 02h] Present bit in context entry is clear > (XEN) print_vtd_entries: iommu = ffff83013fffaee0 bdf = 5:8.0 gmfn > 20560a > (XEN) root_entry = ffff83013ff37000 > (XEN) root_entry[5] = 13cf12001 > (XEN) context = ffff83013cf12000 > (XEN) context[40] = 0_0 > (XEN) ctxt_entry[40] not present > (XEN) [VT-D]iommu.c:796: DMAR:[DMA Write] Request device [05:08.0] fault > addr 206003000, iommu reg = ffff82c3fff57000 > (XEN) DMAR:[fault reason 02h] Present bit in context entry is clear > (XEN) print_vtd_entries: iommu = ffff83013fffaee0 bdf = 5:8.0 gmfn > 206003 > (XEN) root_entry = ffff83013ff37000 > (XEN) root_entry[5] = 13cf12001 > (XEN) context = ffff83013cf12000 > (XEN) context[40] = 0_0 > (XEN) ctxt_entry[40] not present > (XEN) [VT-D]iommu.c:821: iommu_fault_status: Primary Pending Fault > (XEN) [VT-D]iommu.c:796: DMAR:[DMA Write] Request device [05:08.0] fault > addr 20583e000, iommu reg = ffff82c3fff57000 > (XEN) DMAR:[fault reason 02h] Present bit in context entry is clear > (XEN) print_vtd_entries: iommu = ffff83013fffaee0 bdf = 5:8.0 gmfn > 20583e > (XEN) root_entry = ffff83013ff37000 > (XEN) root_entry[5] = 13cf12001 > (XEN) context = ffff83013cf12000 > (XEN) context[40] = 0_0 > (XEN) ctxt_entry[40] not present > (XEN) [VT-D]iommu.c:796: DMAR:[DMA Write] Request device [05:08.0] fault > addr 205615000, iommu reg = ffff82c3fff57000 > (XEN) DMAR:[fault reason 02h] Present bit in context entry is clear > (XEN) print_vtd_entries: iommu = ffff83013fffaee0 bdf = 5:8.0 gmfn > 205615 > (XEN) root_entry = ffff83013ff37000 > (XEN) root_entry[5] = 13cf12001 > (XEN) context = ffff83013cf12000 > (XEN) context[40] = 0_0 > (XEN) ctxt_entry[40] not present > (XEN) [VT-D]iommu.c:796: DMAR:[DMA Write] Request device [05:08.0] fault > addr 204265000, iommu reg = ffff82c3fff57000 > (XEN) DMAR:[fault reason 02h] Present bit in context entry is clear > (XEN) print_vtd_entries: iommu = ffff83013fffaee0 bdf = 5:8.0 gmfn > 204265 > (XEN) root_entry = ffff83013ff37000 > (XEN) root_entry[5] = 13cf12001 > (XEN) context = ffff83013cf12000 > (XEN) context[40] = 0_0 > (XEN) ctxt_entry[40] not present > (XEN) [VT-D]iommu.c:821: iommu_fault_status: Primary Pending Fault > (XEN) [VT-D]iommu.c:796: DMAR:[DMA Write] Request device [05:08.0] fault > addr 207498000, iommu reg = ffff82c3fff57000 > (XEN) DMAR:[fault reason 02h] Present bit in context entry is clear > (XEN) print_vtd_entries: iommu = ffff83013fffaee0 bdf = 5:8.0 gmfn > 207498 > (XEN) root_entry = ffff83013ff37000 > (XEN) root_entry[5] = 13cf12001 > (XEN) context = ffff83013cf12000 > (XEN) context[40] = 0_0 > (XEN) ctxt_entry[40] not present > (XEN) [VT-D]iommu.c:821: iommu_fault_status: Primary Pending Fault > (XEN) [VT-D]iommu.c:796: DMAR:[DMA Write] Request device [05:08.0] fault > addr 2049d1000, iommu reg = ffff82c3fff57000 > (XEN) DMAR:[fault reason 02h] Present bit in context entry is clear > (XEN) print_vtd_entries: iommu = ffff83013fffaee0 bdf = 5:8.0 gmfn > 2049d1 > (XEN) root_entry = ffff83013ff37000 > (XEN) root_entry[5] = 13cf12001 > (XEN) context = ffff83013cf12000 > (XEN) context[40] = 0_0 > (XEN) ctxt_entry[40] not present > (XEN) [VT-D]iommu.c:821: iommu_fault_status: Primary Pending Fault > (XEN) [VT-D]iommu.c:796: DMAR:[DMA Write] Request device [05:08.0] fault > addr 20488e000, iommu reg = ffff82c3fff57000 > (XEN) DMAR:[fault reason 02h] Present bit in context entry is clear > (XEN) print_vtd_entries: iommu = ffff83013fffaee0 bdf = 5:8.0 gmfn > 20488e > (XEN) root_entry = ffff83013ff37000 > (XEN) root_entry[5] = 13cf12001 > (XEN) context = ffff83013cf12000 > (XEN) context[40] = 0_0 > (XEN) ctxt_entry[40] not present > (XEN) [VT-D]iommu.c:821: iommu_fault_status: Primary Pending Fault > (XEN) [VT-D]iommu.c:796: DMAR:[DMA Write] Request device [05:08.0] fault > addr 205495000, iommu reg = ffff82c3fff57000 > (XEN) DMAR:[fault reason 02h] Present bit in context entry is clear > (XEN) print_vtd_entries: iommu = ffff83013fffaee0 bdf = 5:8.0 gmfn > 205495 > (XEN) root_entry = ffff83013ff37000 > (XEN) root_entry[5] = 13cf12001 > (XEN) context = ffff83013cf12000 > (XEN) context[40] = 0_0 > (XEN) ctxt_entry[40] not present > (XEN) [VT-D]iommu.c:821: iommu_fault_status: Primary Pending Fault > (XEN) [VT-D]iommu.c:796: DMAR:[DMA Write] Request device [05:08.0] fault > addr 2072d8000, iommu reg = ffff82c3fff57000 > (XEN) DMAR:[fault reason 02h] Present bit in context entry is clear > (XEN) print_vtd_entries: iommu = ffff83013fffaee0 bdf = 5:8.0 gmfn > 2072d8 > (XEN) root_entry = ffff83013ff37000 > (XEN) root_entry[5] = 13cf12001 > (XEN) context = ffff83013cf12000 > (XEN) context[40] = 0_0 > (XEN) ctxt_entry[40] not present > (XEN) [VT-D]iommu.c:821: iommu_fault_status: Primary Pending Fault > (XEN) [VT-D]iommu.c:796: DMAR:[DMA Write] Request device [05:08.0] fault > addr 2055ae000, iommu reg = ffff82c3fff57000 > (XEN) DMAR:[fault reason 02h] Present bit in context entry is clear > (XEN) print_vtd_entries: iommu = ffff83013fffaee0 bdf = 5:8.0 gmfn > 2055ae > (XEN) root_entry = ffff83013ff37000 > (XEN) root_entry[5] = 13cf12001 > (XEN) context = ffff83013cf12000 > (XEN) context[40] = 0_0 > (XEN) ctxt_entry[40] not present > (XEN) [VT-D]iommu.c:821: iommu_fault_status: Primary Pending Fault > (XEN) [VT-D]iommu.c:796: DMAR:[DMA Write] Request device [05:08.0] fault > addr 205544000, iommu reg = ffff82c3fff57000 > (XEN) DMAR:[fault reason 02h] Present bit in context entry is clear > (XEN) print_vtd_entries: iommu = ffff83013fffaee0 bdf = 5:8.0 gmfn > 205544 > (XEN) root_entry = ffff83013ff37000 > (XEN) root_entry[5] = 13cf12001 > (XEN) context = ffff83013cf12000 > (XEN) context[40] = 0_0 > (XEN) ctxt_entry[40] not present > (XEN) [VT-D]iommu.c:796: DMAR:[DMA Write] Request device [05:08.0] fault > addr 204865000, iommu reg = ffff82c3fff57000 > (XEN) DMAR:[fault reason 02h] Present bit in context entry is clear > (XEN) print_vtd_entries: iommu = ffff83013fffaee0 bdf = 5:8.0 gmfn > 204865 > (XEN) root_entry = ffff83013ff37000 > (XEN) root_entry[5] = 13cf12001 > (XEN) context = ffff83013cf12000 > (XEN) context[40] = 0_0 > (XEN) ctxt_entry[40] not present > (XEN) [VT-D]iommu.c:821: iommu_fault_status: Primary Pending Fault > (XEN) [VT-D]iommu.c:796: DMAR:[DMA Write] Request device [05:08.0] fault > addr 2074be000, iommu reg = ffff82c3fff57000 > (XEN) DMAR:[fault reason 02h] Present bit in context entry is clear > (XEN) print_vtd_entries: iommu = ffff83013fffaee0 bdf = 5:8.0 gmfn > 2074be > (XEN) root_entry = ffff83013ff37000 > (XEN) root_entry[5] = 13cf12001 > (XEN) context = ffff83013cf12000 > (XEN) context[40] = 0_0 > (XEN) ctxt_entry[40] not present > > (XEN) [VT-D]iommu.c:796: DMAR:[DMA Write] Request device [05:08.0] fault > addr 204865000, iommu reg = ffff82c3fff57000 > (XEN) DMAR:[fault reason 02h] Present bit in context entry is clear > (XEN) print_vtd_entries: iommu = ffff83013fffaee0 bdf = 5:8.0 gmfn > 204865 > (XEN) root_entry = ffff83013ff37000 > (XEN) root_entry[5] = 13cf12001 > (XEN) context = ffff83013cf12000 > (XEN) context[40] = 0_0 > (XEN) ctxt_entry[40] not present > (XEN) [VT-D]iommu.c:821: iommu_fault_status: Primary Pending Fault > (XEN) [VT-D]iommu.c:796: DMAR:[DMA Write] Request device [05:08.0] fault > addr 2074be000, iommu reg = ffff82c3fff57000 > (XEN) DMAR:[fault reason 02h] Present bit in context entry is clear > (XEN) print_vtd_entries: iommu = ffff83013fffaee0 bdf = 5:8.0 gmfn > 2074be > (XEN) root_entry = ffff83013ff37000 > (XEN) root_entry[5] = 13cf12001 > (XEN) context = ffff83013cf12000 > (XEN) context[40] = 0_0 > (XEN) ctxt_entry[40] not present > > (XEN) [VT-D]iommu.c:796: DMAR:[DMA Write] Request device [05:08.0] fault > addr 204865000, iommu reg = ffff82c3fff57000 > (XEN) DMAR:[fault reason 02h] Present bit in context entry is clear > (XEN) print_vtd_entries: iommu = ffff83013fffaee0 bdf = 5:8.0 gmfn > 204865 > (XEN) root_entry = ffff83013ff37000 > (XEN) root_entry[5] = 13cf12001 > (XEN) context = ffff83013cf12000 > (XEN) context[40] = 0_0 > (XEN) ctxt_entry[40] not present > (XEN) [VT-D]iommu.c:821: iommu_fault_status: Primary Pending Fault > (XEN) [VT-D]iommu.c:796: DMAR:[DMA Write] Request device [05:08.0] fault > addr 2074be000, iommu reg = ffff82c3fff57000 > (XEN) DMAR:[fault reason 02h] Present bit in context entry is clear > (XEN) print_vtd_entries: iommu = ffff83013fffaee0 bdf = 5:8.0 gmfn > 2074be > (XEN) root_entry = ffff83013ff37000 > (XEN) root_entry[5] = 13cf12001 > (XEN) context = ffff83013cf12000 > (XEN) context[40] = 0_0 > (XEN) ctxt_entry[40] not present > > (XEN) [VT-D]iommu.c:796: DMAR:[DMA Write] Request device [05:08.0] fault > addr 204865000, iommu reg = ffff82c3fff57000 > (XEN) DMAR:[fault reason 02h] Present bit in context entry is clear > (XEN) print_vtd_entries: iommu = ffff83013fffaee0 bdf = 5:8.0 gmfn > 204865 > (XEN) root_entry = ffff83013ff37000 > (XEN) root_entry[5] = 13cf12001 > (XEN) context = ffff83013cf12000 > (XEN) context[40] = 0_0 > (XEN) ctxt_entry[40] not present > (XEN) [VT-D]iommu.c:821: iommu_fault_status: Primary Pending Fault > (XEN) [VT-D]iommu.c:796: DMAR:[DMA Write] Request device [05:08.0] fault > addr 2074be000, iommu reg = ffff82c3fff57000 > (XEN) DMAR:[fault reason 02h] Present bit in context entry is clear > (XEN) print_vtd_entries: iommu = ffff83013fffaee0 bdf = 5:8.0 gmfn > 2074be > (XEN) root_entry = ffff83013ff37000 > (XEN) root_entry[5] = 13cf12001 > (XEN) context = ffff83013cf12000 > (XEN) context[40] = 0_0 > (XEN) ctxt_entry[40] not present > > (XEN) [VT-D]iommu.c:796: DMAR:[DMA Write] Request device [05:08.0] fault > addr 204865000, iommu reg = ffff82c3fff57000 > (XEN) DMAR:[fault reason 02h] Present bit in context entry is clear > (XEN) print_vtd_entries: iommu = ffff83013fffaee0 bdf = 5:8.0 gmfn > 204865 > (XEN) root_entry = ffff83013ff37000 > (XEN) root_entry[5] = 13cf12001 > (XEN) context = ffff83013cf12000 > (XEN) context[40] = 0_0 > (XEN) ctxt_entry[40] not present > (XEN) [VT-D]iommu.c:821: iommu_fault_status: Primary Pending Fault > (XEN) [VT-D]iommu.c:796: DMAR:[DMA Write] Request device [05:08.0] fault > addr 2074be000, iommu reg = ffff82c3fff57000 > (XEN) DMAR:[fault reason 02h] Present bit in context entry is clear > (XEN) print_vtd_entries: iommu = ffff83013fffaee0 bdf = 5:8.0 gmfn > 2074be > (XEN) root_entry = ffff83013ff37000 > (XEN) root_entry[5] = 13cf12001 > (XEN) context = ffff83013cf12000 > (XEN) context[40] = 0_0 > (XEN) ctxt_entry[40] not present > > (XEN) [VT-D]iommu.c:796: DMAR:[DMA Write] Request device [05:08.0] fault > addr 204865000, iommu reg = ffff82c3fff57000 > (XEN) DMAR:[fault reason 02h] Present bit in context entry is clear > (XEN) print_vtd_entries: iommu = ffff83013fffaee0 bdf = 5:8.0 gmfn > 204865 > (XEN) root_entry = ffff83013ff37000 > (XEN) root_entry[5] = 13cf12001 > (XEN) context = ffff83013cf12000 > (XEN) context[40] = 0_0 > (XEN) ctxt_entry[40] not present > (XEN) [VT-D]iommu.c:821: iommu_fault_status: Primary Pending Fault > (XEN) [VT-D]iommu.c:796: DMAR:[DMA Write] Request device [05:08.0] fault > addr 2074be000, iommu reg = ffff82c3fff57000 > (XEN) DMAR:[fault reason 02h] Present bit in context entry is clear > (XEN) print_vtd_entries: iommu = ffff83013fffaee0 bdf = 5:8.0 gmfn > 2074be > (XEN) root_entry = ffff83013ff37000 > (XEN) root_entry[5] = 13cf12001 > (XEN) context = ffff83013cf12000 > (XEN) context[40] = 0_0 > (XEN) ctxt_entry[40] not present > > (XEN) [VT-D]iommu.c:796: DMAR:[DMA Write] Request device [05:08.0] fault > addr 204865000, iommu reg = ffff82c3fff57000 > (XEN) DMAR:[fault reason 02h] Present bit in context entry is clear > (XEN) print_vtd_entries: iommu = ffff83013fffaee0 bdf = 5:8.0 gmfn > 204865 > (XEN) root_entry = ffff83013ff37000 > (XEN) root_entry[5] = 13cf12001 > (XEN) context = ffff83013cf12000 > (XEN) context[40] = 0_0 > (XEN) ctxt_entry[40] not present > (XEN) [VT-D]iommu.c:821: iommu_fault_status: Primary Pending Fault > (XEN) [VT-D]iommu.c:796: DMAR:[DMA Write] Request device [05:08.0] fault > addr 2074be000, iommu reg = ffff82c3fff57000 > (XEN) DMAR:[fault reason 02h] Present bit in context entry is clear > (XEN) print_vtd_entries: iommu = ffff83013fffaee0 bdf = 5:8.0 gmfn > 2074be > (XEN) root_entry = ffff83013ff37000 > (XEN) root_entry[5] = 13cf12001 > (XEN) context = ffff83013cf12000 > (XEN) context[40] = 0_0 > (XEN) ctxt_entry[40] not present > > (XEN) context[40] = 0_0 > (XEN) ctxt_entry[40] not present > (XEN) [VT-D]iommu.c:796: DMAR:[DMA Write] Request device [05:08.0] fault > addr 204865000, iommu reg = ffff82c3fff57000 > (XEN) DMAR:[fault reason 02h] Present bit in context entry is clear > (XEN) print_vtd_entries: iommu = ffff83013fffaee0 bdf = 5:8.0 gmfn > 204865 > (XEN) root_entry = ffff83013ff37000 > (XEN) root_entry[5] = 13cf12001 > (XEN) context = ffff83013cf12000 > (XEN) context[40] = 0_0 > (XEN) ctxt_entry[40] not present > (XEN) [VT-D]iommu.c:821: iommu_fault_status: Primary Pending Fault > (XEN) [VT-D]iommu.c:796: DMAR:[DMA Write] Request device [05:08.0] fault > addr 2074be000, iommu reg = ffff82c3fff57000 > (XEN) DMAR:[fault reason 02h] Present bit in context entry is clear > (XEN) print_vtd_entries: iommu = ffff83013fffaee0 bdf = 5:8.0 gmfn > 2074be > (XEN) root_entry = ffff83013ff37000 > (XEN) root_entry[5] = 13cf12001 > (XEN) context = ffff83013cf12000 > (XEN) context[40] = 0_0 > (XEN) ctxt_entry[40] not present > > (XEN) context[40] = 0_0 > (XEN) ctxt_entry[40] not present > (XEN) [VT-D]iommu.c:796: DMAR:[DMA Write] Request device [05:08.0] fault > addr 204865000, iommu reg = ffff82c3fff57000 > (XEN) DMAR:[fault reason 02h] Present bit in context entry is clear > (XEN) print_vtd_entries: iommu = ffff83013fffaee0 bdf = 5:8.0 gmfn > 204865 > (XEN) root_entry = ffff83013ff37000 > (XEN) root_entry[5] = 13cf12001 > (XEN) context = ffff83013cf12000 > (XEN) context[40] = 0_0 > (XEN) ctxt_entry[40] not present > (XEN) [VT-D]iommu.c:821: iommu_fault_status: Primary Pending Fault > (XEN) [VT-D]iommu.c:796: DMAR:[DMA Write] Request device [05:08.0] fault > addr 2074be000, iommu reg = ffff82c3fff57000 > (XEN) DMAR:[fault reason 02h] Present bit in context entry is clear > (XEN) print_vtd_entries: iommu = ffff83013fffaee0 bdf = 5:8.0 gmfn > 2074be > (XEN) root_entry = ffff83013ff37000 > (XEN) root_entry[5] = 13cf12001 > (XEN) context = ffff83013cf12000 > (XEN) context[40] = 0_0 > (XEN) ctxt_entry[40] not present > > (XEN) context[40] = 0_0 > (XEN) ctxt_entry[40] not present > (XEN) [VT-D]iommu.c:796: DMAR:[DMA Write] Request device [05:08.0] fault > addr 204865000, iommu reg = ffff82c3fff57000 > (XEN) DMAR:[fault reason 02h] Present bit in context entry is clear > (XEN) print_vtd_entries: iommu = ffff83013fffaee0 bdf = 5:8.0 gmfn > 204865 > (XEN) root_entry = ffff83013ff37000 > (XEN) root_entry[5] = 13cf12001 > (XEN) context = ffff83013cf12000 > (XEN) context[40] = 0_0 > (XEN) ctxt_entry[40] not present > (XEN) [VT-D]iommu.c:821: iommu_fault_status: Primary Pending Fault > (XEN) [VT-D]iommu.c:796: DMAR:[DMA Write] Request device [05:08.0] fault > addr 2074be000, iommu reg = ffff82c3fff57000 > (XEN) DMAR:[fault reason 02h] Present bit in context entry is clear > (XEN) print_vtd_entries: iommu = ffff83013fffaee0 bdf = 5:8.0 gmfn > 2074be > (XEN) root_entry = ffff83013ff37000 > (XEN) root_entry[5] = 13cf12001 > (XEN) context = ffff83013cf12000 > (XEN) context[40] = 0_0 > (XEN) ctxt_entry[40] not present > > (XEN) context[40] = 0_0 > (XEN) ctxt_entry[40] not present > (XEN) [VT-D]iommu.c:796: DMAR:[DMA Write] Request device [05:08.0] fault > addr 204865000, iommu reg = ffff82c3fff57000 > (XEN) DMAR:[fault reason 02h] Present bit in context entry is clear > (XEN) print_vtd_entries: iommu = ffff83013fffaee0 bdf = 5:8.0 gmfn > 204865 > (XEN) root_entry = ffff83013ff37000 > (XEN) root_entry[5] = 13cf12001 > (XEN) context = ffff83013cf12000 > (XEN) context[40] = 0_0 > (XEN) ctxt_entry[40] not present > (XEN) [VT-D]iommu.c:821: iommu_fault_status: Primary Pending Fault > (XEN) [VT-D]iommu.c:796: DMAR:[DMA Write] Request device [05:08.0] fault > addr 2074be000, iommu reg = ffff82c3fff57000 > (XEN) DMAR:[fault reason 02h] Present bit in context entry is clear > (XEN) print_vtd_entries: iommu = ffff83013fffaee0 bdf = 5:8.0 gmfn > 2074be > (XEN) root_entry = ffff83013ff37000 > (XEN) root_entry[5] = 13cf12001 > (XEN) context = ffff83013cf12000 > (XEN) context[40] = 0_0 > (XEN) ctxt_entry[40] not present > > > _______________________________________________ > Xen-devel mailing list > Xen-devel@lists.xensource.com > http://lists.xensource.com/xen-devel_______________________________________________ Xen-devel mailing list Xen-devel@lists.xensource.com http://lists.xensource.com/xen-devel
M. Nunberg
2010-May-30 18:33 UTC
Re: [Xen-devel] iommuu/vt-d issues with LSI MegaSAS (PERC5i)
Here is the full log, kernel + xen
\ \/ /___ _ __ | || | / _ \ / | _ __ ___/ |
\ // _ \ ''_ \ | || |_| | | || |__| ''__/ __| |
/ \ __/ | | | |__ _| |_| || |__| | | (__| |
/_/\_\___|_| |_| |_|(_)___(_)_| |_| \___|_|
(XEN) Xen version 4.0.1-rc1 (mordy@) (gcc version 4.3.2 (Debian
4.3.2-1.1) ) Fri May 28 16:46:04 PDT 2010
(XEN) Latest ChangeSet: Sat May 22 07:18:16 2010 +0100
21162:370fd9f97c70
(XEN) Console output is synchronous.
(XEN) Command line: iommu=verbose loglvl=all guest_loglvl=all
sync_console console_to_rint com1=115200,8n1 console=com1
(XEN) Video information:
(XEN) VGA is text mode 80x25, font 8x16
(XEN) VBE/DDC methods: none; EDID transfer time: 0 seconds
(XEN) EDID info not retrieved because no DDC retrieval method detected
(XEN) Disc information:
(XEN) Found 1 MBR signatures
(XEN) Found 1 EDD information structures
(XEN) Xen-e820 RAM map:
(XEN) 0000000000000000 - 000000000009a000 (usable)
(XEN) 000000000009a000 - 00000000000a0000 (reserved)
(XEN) 00000000000e0000 - 0000000000100000 (reserved)
(XEN) 0000000000100000 - 00000000bf760000 (usable)
(XEN) 00000000bf76e000 - 00000000bf770000 type 9
(XEN) 00000000bf770000 - 00000000bf77e000 (ACPI data)
(XEN) 00000000bf77e000 - 00000000bf7d0000 (ACPI NVS)
(XEN) 00000000bf7d0000 - 00000000bf7e0000 (reserved)
(XEN) 00000000bf7ec000 - 00000000c0000000 (reserved)
(XEN) 00000000fee00000 - 00000000fee01000 (reserved)
(XEN) 00000000ffc00000 - 0000000100000000 (reserved)
(XEN) 0000000100000000 - 0000000340000000 (usable)
(XEN) ACPI: RSDP 000F9E10, 0024 (r2 ACPIAM)
(XEN) ACPI: XSDT BF770100, 0094 (r1 NEC 20090424 MSFT
97)
(XEN) ACPI: FACP BF770290, 00F4 (r4 042409 FACP1917 20090424 MSFT
97)
(XEN) ACPI: DSDT BF770670, 5BFB (r2 10601 10601000 0 INTL
20051117)
(XEN) ACPI: FACS BF77E000, 0040
(XEN) ACPI: APIC BF770390, 00D2 (r2 042409 APIC1917 20090424 MSFT
97)
(XEN) ACPI: MCFG BF770470, 003C (r1 042409 OEMMCFG 20090424 MSFT
97)
(XEN) ACPI: SLIC BF7704B0, 0176 (r1 NEC 20090424 MSFT
97)
(XEN) ACPI: ERST BF770630, 0040 (r1 042409 WHEA1917 20090424 MSFT
97)
(XEN) ACPI: OEMB BF77E040, 007B (r1 042409 OEMB1917 20090424 MSFT
97)
(XEN) ACPI: SRAT BF77A670, 01D0 (r1 042409 OEMSRAT 1 INTL
1)
(XEN) ACPI: HPET BF77A840, 0038 (r1 042409 OEMHPET 20090424 MSFT
97)
(XEN) ACPI: DMAR BF77E0C0, 0118 (r1 AMI OEMDMAR 1 MSFT
97)
(XEN) ACPI: SSDT BF781DF0, 0363 (r1 DpgPmm CpuPm 12 INTL
20051117)
(XEN) ACPI: EINJ BF77A880, 0130 (r1 AMIER AMI_EINJ 20090424 MSFT
97)
(XEN) ACPI: BERT BF77AA10, 0030 (r1 AMIER AMI_BERT 20090424 MSFT
97)
(XEN) ACPI: ERST BF77AA40, 01B0 (r1 AMIER AMI_ERST 20090424 MSFT
97)
(XEN) ACPI: HEST BF77ABF0, 00A8 (r1 AMIER AMI_HEST 20090424 MSFT
97)
(XEN) System RAM: 12278MB (12573672kB)
(XEN) SRAT: PXM 0 -> APIC 0 -> Node 0
(XEN) SRAT: PXM 0 -> APIC 2 -> Node 0
(XEN) SRAT: PXM 0 -> APIC 4 -> Node 0
(XEN) SRAT: PXM 0 -> APIC 6 -> Node 0
(XEN) SRAT: PXM 0 -> APIC 1 -> Node 0
(XEN) SRAT: PXM 0 -> APIC 3 -> Node 0
(XEN) SRAT: PXM 0 -> APIC 5 -> Node 0
(XEN) SRAT: PXM 0 -> APIC 7 -> Node 0
(XEN) SRAT: PXM 1 -> APIC 16 -> Node 1
(XEN) SRAT: PXM 1 -> APIC 18 -> Node 1
(XEN) SRAT: PXM 1 -> APIC 20 -> Node 1
(XEN) SRAT: PXM 1 -> APIC 22 -> Node 1
(XEN) SRAT: PXM 1 -> APIC 17 -> Node 1
(XEN) SRAT: PXM 1 -> APIC 19 -> Node 1
(XEN) SRAT: PXM 1 -> APIC 21 -> Node 1
(XEN) SRAT: PXM 1 -> APIC 23 -> Node 1
(XEN) SRAT: Node 0 PXM 0 0-a0000
(XEN) SRAT: Node 0 PXM 0 100000-c0000000
(XEN) SRAT: Node 0 PXM 0 100000000-1c0000000
(XEN) SRAT: Node 1 PXM 1 1c0000000-340000000
(XEN) NUMA: Allocated memnodemap from 33fdfb000 - 33fdff000
(XEN) NUMA: Using 8 for the hash shift.
(XEN) Domain heap initialised DMA width 30 bits
(XEN) found SMP MP-table at 000ff780
(XEN) DMI present.
(XEN) Using APIC driver default
(XEN) ACPI: PM-Timer IO Port: 0x808
(XEN) ACPI: ACPI SLEEP INFO: pm1x_cnt[804,0], pm1x_evt[800,0]
(XEN) ACPI: wakeup_vec[bf77e00c], vec_size[20]
(XEN) ACPI: Local APIC address 0xfee00000
(XEN) ACPI: LAPIC (acpi_id[0x01] lapic_id[0x00] enabled)
(XEN) Processor #0 7:10 APIC version 21
(XEN) ACPI: LAPIC (acpi_id[0x02] lapic_id[0x10] enabled)
(XEN) Processor #16 7:10 APIC version 21
(XEN) ACPI: LAPIC (acpi_id[0x03] lapic_id[0x02] enabled)
(XEN) Processor #2 7:10 APIC version 21
(XEN) ACPI: LAPIC (acpi_id[0x04] lapic_id[0x12] enabled)
(XEN) Processor #18 7:10 APIC version 21
(XEN) ACPI: LAPIC (acpi_id[0x05] lapic_id[0x04] enabled)
(XEN) Processor #4 7:10 APIC version 21
(XEN) ACPI: LAPIC (acpi_id[0x06] lapic_id[0x14] enabled)
(XEN) Processor #20 7:10 APIC version 21
(XEN) ACPI: LAPIC (acpi_id[0x07] lapic_id[0x06] enabled)
(XEN) Processor #6 7:10 APIC version 21
(XEN) ACPI: LAPIC (acpi_id[0x08] lapic_id[0x16] enabled)
(XEN) Processor #22 7:10 APIC version 21
(XEN) ACPI: LAPIC (acpi_id[0x09] lapic_id[0x01] enabled)
(XEN) Processor #1 7:10 APIC version 21
(XEN) ACPI: LAPIC (acpi_id[0x0a] lapic_id[0x11] enabled)
(XEN) Processor #17 7:10 APIC version 21
(XEN) ACPI: LAPIC (acpi_id[0x0b] lapic_id[0x03] enabled)
(XEN) Processor #3 7:10 APIC version 21
(XEN) ACPI: LAPIC (acpi_id[0x0c] lapic_id[0x13] enabled)
(XEN) Processor #19 7:10 APIC version 21
(XEN) ACPI: LAPIC (acpi_id[0x0d] lapic_id[0x05] enabled)
(XEN) Processor #5 7:10 APIC version 21
(XEN) ACPI: LAPIC (acpi_id[0x0e] lapic_id[0x15] enabled)
(XEN) Processor #21 7:10 APIC version 21
(XEN) ACPI: LAPIC (acpi_id[0x0f] lapic_id[0x07] enabled)
(XEN) Processor #7 7:10 APIC version 21
(XEN) ACPI: LAPIC (acpi_id[0x10] lapic_id[0x17] enabled)
(XEN) Processor #23 7:10 APIC version 21
(XEN) ACPI: LAPIC_NMI (acpi_id[0xff] dfl dfl lint[0x1])
(XEN) Overriding APIC driver with bigsmp
(XEN) ACPI: IOAPIC (id[0x08] address[0xfec00000] gsi_base[0])
(XEN) IOAPIC[0]: apic_id 8, version 32, address 0xfec00000, GSI 0-23
(XEN) ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
(XEN) ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 20 low level)
(XEN) ACPI: IRQ0 used by override.
(XEN) ACPI: IRQ2 used by override.
(XEN) ACPI: IRQ9 used by override.
(XEN) Enabling APIC mode: Phys. Using 1 I/O APICs
(XEN) ACPI: HPET id: 0xffffffff base: 0xfed00000
(XEN) [VT-D]dmar.c:679: Host address width 40
(XEN) [VT-D]dmar.c:694: found ACPI_DMAR_DRHD:
(XEN) [VT-D]dmar.c:398: dmaru->address = fbffe000
(XEN) [VT-D]dmar.c:340: IOAPIC: f0:1f.7
(XEN) [VT-D]dmar.c:411: flags: INCLUDE_ALL
(XEN) [VT-D]dmar.c:699: found ACPI_DMAR_RMRR:
(XEN) [VT-D]dmar.c:334: endpoint: 0:1d.0
(XEN) [VT-D]dmar.c:334: endpoint: 0:1d.1
(XEN) [VT-D]dmar.c:334: endpoint: 0:1d.2
(XEN) [VT-D]dmar.c:334: endpoint: 0:1d.7
(XEN) [VT-D]dmar.c:334: endpoint: 0:1a.0
(XEN) [VT-D]dmar.c:334: endpoint: 0:1a.1
(XEN) [VT-D]dmar.c:334: endpoint: 0:1a.2
(XEN) [VT-D]dmar.c:334: endpoint: 0:1a.7
(XEN) [VT-D]dmar.c:571: RMRR region: base_addr ec000 end_address effff
(XEN) [VT-D]dmar.c:699: found ACPI_DMAR_RMRR:
(XEN) [VT-D]dmar.c:334: endpoint: 0:1d.0
(XEN) [VT-D]dmar.c:334: endpoint: 0:1d.1
(XEN) [VT-D]dmar.c:334: endpoint: 0:1d.2
(XEN) [VT-D]dmar.c:334: endpoint: 0:1d.7
(XEN) [VT-D]dmar.c:334: endpoint: 0:1a.0
(XEN) [VT-D]dmar.c:334: endpoint: 0:1a.1
(XEN) [VT-D]dmar.c:334: endpoint: 0:1a.2
(XEN) [VT-D]dmar.c:334: endpoint: 0:1a.7
(XEN) [VT-D]dmar.c:571: RMRR region: base_addr bf7ec000 end_address
bf7fffff
(XEN) [VT-D]dmar.c:704: found ACPI_DMAR_ATSR:
(XEN) [VT-D]dmar.c:599: atsru->all_ports: 0
(XEN) [VT-D]dmar.c:320: bridge: 0:1.0 start = 0 sec = 1 sub = 1
(XEN) [VT-D]dmar.c:320: bridge: 0:3.0 start = 0 sec = 2 sub = 2
(XEN) [VT-D]dmar.c:320: bridge: 0:7.0 start = 0 sec = 3 sub = 3
(XEN) PCI: MCFG configuration 0: base e0000000 segment 0 buses 0 - 255
(XEN) PCI: Not using MMCONFIG.
(XEN) Using ACPI (MADT) for SMP configuration information
(XEN) Using scheduler: SMP Credit Scheduler (credit)
(XEN) Detected 2266.784 MHz processor.
(XEN) Initing memory sharing.
(XEN) VMX: Supported advanced features:
(XEN) - APIC MMIO access virtualisation
(XEN) - APIC TPR shadow
(XEN) - Extended Page Tables (EPT)
(XEN) - Virtual-Processor Identifiers (VPID)
(XEN) - Virtual NMI
(XEN) - MSR direct-access bitmap
(XEN) HVM: ASIDs enabled.
(XEN) HVM: VMX enabled
(XEN) HVM: Hardware Assisted Paging detected.
(XEN) Intel machine check reporting enabled
(XEN) [VT-D]iommu.c:1078: drhd->address = fbffe000 iommu->reg
ffff82c3fff57000
(XEN) [VT-D]iommu.c:1080: cap = c90780106f0462 ecap = f0207e
(XEN) Intel VT-d Snoop Control not supported.
(XEN) Intel VT-d DMA Passthrough not supported.
(XEN) Intel VT-d Queued Invalidation supported.
(XEN) Intel VT-d Interrupt Remapping supported.
(XEN) I/O virtualisation enabled
(XEN) I/O virtualisation for PV guests disabled
(XEN) Total of 16 processors activated.
(XEN) ENABLING IO-APIC IRQs
(XEN) -> Using new ACK method
(XEN) ..TIMER: vector=0xF0 apic1=0 pin1=2 apic2=-1 pin2=-1
(XEN) TSC is reliable, synchronization unnecessary
(XEN) Platform timer is 14.318MHz HPET
ÿ(XEN) Allocated console ring of 128 KiB.
(XEN) microcode.c:73:d32767 microcode: CPU1 resumed
(XEN) microcode.c:73:d32767 microcode: CPU9 resumed
(XEN) microcode.c:73:d32767 microcode: CPU6 resumed
(XEN) microcode.c:73:d32767 microcode: CPU14 resumed
(XEN) microcode.c:73:d32767 microcode: CPU7 resumed
(XEN) microcode.c:73:d32767 microcode: CPU15 resumed
(XEN) microcode.c:73:d32767 microcode: CPU10 resumed
(XEN) microcode.c:73:d32767 microcode: CPU13 resumed
(XEN) microcode.c:73:d32767 microcode: CPU5 resumed
(XEN) microcode.c:73:d32767 microcode: CPU2 resumed
(XEN) microcode.c:73:d32767 microcode: CPU3 resumed
(XEN) microcode.c:73:d32767 microcode: CPU11 resumed
(XEN) microcode.c:73:d32767 microcode: CPU12 resumed
(XEN) microcode.c:73:d32767 microcode: CPU8 resumed
(XEN) microcode.c:73:d32767 microcode: CPU4 resumed
(XEN) Brought up 16 CPUs
(XEN) Turbo Mode detected!
(XEN) HPET''s MSI mode hasn''t been supported when Interrupt
Remapping is
enabled.
(XEN) ACPI sleep modes: S3
(XEN) mcheck_poll: Machine check polling timer started.
(XEN) [VT-D]iommu.c:1325: d0:PCIe: map bdf = 0:0.0
(XEN) [VT-D]iommu.c:1325: d0:PCIe: map bdf = 0:14.0
(XEN) [VT-D]iommu.c:1325: d0:PCIe: map bdf = 0:14.1
(XEN) [VT-D]iommu.c:1325: d0:PCIe: map bdf = 0:14.2
(XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = 0:14.3
(XEN) [VT-D]iommu.c:1325: d0:PCIe: map bdf = 0:16.0
(XEN) [VT-D]iommu.c:1325: d0:PCIe: map bdf = 0:16.1
(XEN) [VT-D]iommu.c:1325: d0:PCIe: map bdf = 0:16.2
(XEN) [VT-D]iommu.c:1325: d0:PCIe: map bdf = 0:16.3
(XEN) [VT-D]iommu.c:1325: d0:PCIe: map bdf = 0:16.4
(XEN) [VT-D]iommu.c:1325: d0:PCIe: map bdf = 0:16.5
(XEN) [VT-D]iommu.c:1325: d0:PCIe: map bdf = 0:16.6
(XEN) [VT-D]iommu.c:1325: d0:PCIe: map bdf = 0:16.7
(XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = 0:1a.0
(XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = 0:1a.1
(XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = 0:1a.2
(XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = 0:1a.7
(XEN) [VT-D]iommu.c:1325: d0:PCIe: map bdf = 0:1b.0
(XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = 0:1d.0
(XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = 0:1d.1
(XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = 0:1d.2
(XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = 0:1d.7
(XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = 0:1f.0
(XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = 0:1f.2
(XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = 0:1f.3
(XEN) [VT-D]iommu.c:1325: d0:PCIe: map bdf = 1:0.0
(XEN) [VT-D]iommu.c:1325: d0:PCIe: map bdf = 3:0.0
(XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = 5:e.0
(XEN) [VT-D]iommu.c:1325: d0:PCIe: map bdf = 7:0.0
(XEN) [VT-D]iommu.c:1325: d0:PCIe: map bdf = 8:0.0
(XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = fe:0.0
(XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = fe:0.1
(XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = fe:2.0
(XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = fe:2.1
(XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = fe:2.4
(XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = fe:2.5
(XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = fe:3.0
(XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = fe:3.1
(XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = fe:3.2
(XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = fe:3.4
(XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = fe:4.0
(XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = fe:4.1
(XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = fe:4.2
(XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = fe:4.3
(XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = fe:5.0
(XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = fe:5.1
(XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = fe:5.2
(XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = fe:5.3
(XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = fe:6.0
(XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = fe:6.1
(XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = fe:6.2
(XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = fe:6.3
(XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = ff:0.0
(XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = ff:0.1
(XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = ff:2.0
(XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = ff:2.1
(XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = ff:2.4
(XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = ff:2.5
(XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = ff:3.0
(XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = ff:3.1
(XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = ff:3.2
(XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = ff:3.4
(XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = ff:4.0
(XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = ff:4.1
(XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = ff:4.2
(XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = ff:4.3
(XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = ff:5.0
(XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = ff:5.1
(XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = ff:5.2
(XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = ff:5.3
(XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = ff:6.0
(XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = ff:6.1
(XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = ff:6.2
(XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = ff:6.3
(XEN) [VT-D]iommu.c:695: iommu_enable_translation: iommu->reg
ffff82c3fff57000
(XEN) *** LOADING DOMAIN 0 ***
(XEN) Xen kernel: 64-bit, lsb, compat32
(XEN) Dom0 kernel: 64-bit, PAE, lsb, paddr 0x1000000 -> 0x26b6000
(XEN) PHYSICAL MEMORY ARRANGEMENT:
(XEN) Dom0 alloc.: 0000000100000000->0000000120000000 (2937039 pages
to be allocated)
(XEN) VIRTUAL MEMORY ARRANGEMENT:
(XEN) Loaded kernel: ffffffff81000000->ffffffff826b6000
(XEN) Init. ramdisk: ffffffff826b6000->ffffffff8f7d7600
(XEN) Phys-Mach map: ffffffff8f7d8000->ffffffff90f40678
(XEN) Start info: ffffffff90f41000->ffffffff90f414b4
(XEN) Page tables: ffffffff90f42000->ffffffff90fcf000
(XEN) Boot stack: ffffffff90fcf000->ffffffff90fd0000
(XEN) TOTAL: ffffffff80000000->ffffffff91400000
(XEN) ENTRY ADDRESS: ffffffff819be200
(XEN) Dom0 has maximum 16 VCPUs
(XEN) Scrubbing Free RAM: .done.
(XEN) Xen trace buffers: disabled
(XEN) Std. Loglevel: All
(XEN) Guest Loglevel: All
(XEN) **********************************************
(XEN) ******* WARNING: CONSOLE OUTPUT IS SYNCHRONOUS
(XEN) ******* This option is intended to aid debugging of Xen by
ensuring
(XEN) ******* that all output is synchronously delivered on the serial
line.
(XEN) ******* However it can introduce SIGNIFICANT latencies and affect
(XEN) ******* timekeeping. It is NOT recommended for production use!
(XEN) **********************************************
(XEN) 3... 2... 1...
(XEN) *** Serial input -> DOM0 (type ''CTRL-a'' three times
to switch
input to Xen)
(XEN) Freed 180kB init memory.
mapping kernel into physical memory
Xen: setup ISA identity maps
about to get started...
Initializing cgroup subsys cpuset
Initializing cgroup subsys cpu
Linux version 2.6.32.13 (mordy@debmed) (gcc version 4.3.2 (Debian
4.3.2-1.1) ) #3 SMP Fri May 28 13:20:24 PDT 2010
Command line: root=/dev/mapper/MISC-fedora ro nomodeset console=hvc0
earlyprintk=xen debug initcall_debug loglvel=10
KERNEL supported cpus:
Intel GenuineIntel
AMD AuthenticAMD
Centaur CentaurHauls
xen_release_chunk: looking at area pfn bf760-bf76e: 14 pages freed
xen_release_chunk: looking at area pfn bf7e0-bf7ec: 12 pages freed
xen_release_chunk: looking at area pfn c0000-fec00: 257024 pages freed
xen_release_chunk: looking at area pfn fec01-fee00: 511 pages freed
xen_release_chunk: looking at area pfn fee01-ffc00: 3583 pages freed
released 261144 pages of unused memory
BIOS-provided physical RAM map:
Xen: 0000000000000000 - 000000000009a000 (usable)
Xen: 000000000009a000 - 0000000000100000 (reserved)
Xen: 0000000000100000 - 00000000bf760000 (usable)
Xen: 00000000bf76e000 - 00000000bf770000 type 9
Xen: 00000000bf770000 - 00000000bf77e000 (ACPI data)
Xen: 00000000bf77e000 - 00000000bf7d0000 (ACPI NVS)
Xen: 00000000bf7d0000 - 00000000bf7e0000 (reserved)
Xen: 00000000bf7ec000 - 00000000c0000000 (reserved)
Xen: 00000000fec00000 - 00000000fec01000 (reserved)
Xen: 00000000fee00000 - 00000000fee01000 (reserved)
Xen: 00000000ffc00000 - 0000000100000000 (reserved)
Xen: 0000000100000000 - 00000002ed0cf000 (usable)
bootconsole [xenboot0] enabled
DMI present.
AMI BIOS detected: BIOS may corrupt low RAM, working around it.
e820 update range: 0000000000000000 - 0000000000010000 (usable) ==>
(reserved)
last_pfn = 0x2ed0cf max_arch_pfn = 0x400000000
x86 PAT enabled: cpu 0, old 0x50100070406, new 0x7010600070106
last_pfn = 0xbf760 max_arch_pfn = 0x400000000
initial memory mapped : 0 - 20000000
init_memory_mapping: 0000000000000000-00000000bf760000
0000000000 - 00bf760000 page 4k
kernel direct mapping tables up to bf760000 @ 100000-700000
init_memory_mapping: 0000000100000000-00000002ed0cf000
0100000000 - 02ed0cf000 page 4k
kernel direct mapping tables up to 2ed0cf000 @ 10fcf000-12745000
RAMDISK: 026b6000 - 0f7d7600
ACPI: RSDP 00000000000f9e10 00024 (v02 ACPIAM)
ACPI: XSDT 00000000bf770100 00094 (v01 NEC 20090424 MSFT
00000097)
ACPI: FACP 00000000bf770290 000F4 (v04 042409 FACP1917 20090424 MSFT
00000097)
ACPI: DSDT 00000000bf770670 05BFB (v02 10601 10601000 00000000 INTL
20051117)
ACPI: FACS 00000000bf77e000 00040
ACPI: APIC 00000000bf770390 000D2 (v02 042409 APIC1917 20090424 MSFT
00000097)
ACPI: MCFG 00000000bf770470 0003C (v01 042409 OEMMCFG 20090424 MSFT
00000097)
ACPI: SLIC 00000000bf7704b0 00176 (v01 NEC 20090424 MSFT
00000097)
ACPI: ERST 00000000bf770630 00040 (v01 042409 WHEA1917 20090424 MSFT
00000097)
ACPI: OEMB 00000000bf77e040 0007B (v01 042409 OEMB1917 20090424 MSFT
00000097)
ACPI: SRAT 00000000bf77a670 001D0 (v01 042409 OEMSRAT 00000001 INTL
00000001)
ACPI: HPET 00000000bf77a840 00038 (v01 042409 OEMHPET 20090424 MSFT
00000097)
ACPI: 00000000bf77e0c0 00118 (v01 AMI OEMDMAR 00000001 MSFT
00000097)
ACPI: SSDT 00000000bf781df0 00363 (v01 DpgPmm CpuPm 00000012 INTL
20051117)
ACPI: EINJ 00000000bf77a880 00130 (v01 AMIER AMI_EINJ 20090424 MSFT
00000097)
ACPI: BERT 00000000bf77aa10 00030 (v01 AMIER AMI_BERT 20090424 MSFT
00000097)
ACPI: ERST 00000000bf77aa40 001B0 (v01 AMIER AMI_ERST 20090424 MSFT
00000097)
ACPI: HEST 00000000bf77abf0 000A8 (v01 AMIER AMI_HEST 20090424 MSFT
00000097)
ACPI: Local APIC address 0xfee00000
SRAT: PXM 0 -> APIC 0 -> Node 0
SRAT: PXM 0 -> APIC 2 -> Node 0
SRAT: PXM 0 -> APIC 4 -> Node 0
SRAT: PXM 0 -> APIC 6 -> Node 0
SRAT: PXM 0 -> APIC 1 -> Node 0
SRAT: PXM 0 -> APIC 3 -> Node 0
SRAT: PXM 0 -> APIC 5 -> Node 0
SRAT: PXM 0 -> APIC 7 -> Node 0
SRAT: PXM 1 -> APIC 16 -> Node 1
SRAT: PXM 1 -> APIC 18 -> Node 1
SRAT: PXM 1 -> APIC 20 -> Node 1
SRAT: PXM 1 -> APIC 22 -> Node 1
SRAT: PXM 1 -> APIC 17 -> Node 1
SRAT: PXM 1 -> APIC 19 -> Node 1
SRAT: PXM 1 -> APIC 21 -> Node 1
SRAT: PXM 1 -> APIC 23 -> Node 1
SRAT: Node 0 PXM 0 0-a0000
SRAT: Node 0 PXM 0 100000-c0000000
SRAT: Node 0 PXM 0 100000000-1c0000000
SRAT: Node 2 PXM 257 1c0000000-340000000
NUMA: Allocated memnodemap from 10000 - 16840
NUMA: Using 20 for the hash shift.
Bootmem setup node 0 0000000000000000-00000001c0000000
NODE_DATA [0000000000016840 - 000000000002e83f]
bootmap [000000000002f000 - 0000000000066fff] pages 38
(10 early reservations) ==> bootmem [0000000000 - 01c0000000]
#0 [0000000000 - 0000001000] BIOS data page ==> [0000000000 -
0000001000]
#1 [0010f42000 - 0010fcf000] XEN PAGETABLES ==> [0010f42000 -
0010fcf000]
#2 [0000006000 - 0000008000] TRAMPOLINE ==> [0000006000 -
0000008000]
#3 [0001000000 - 0002695878] TEXT DATA BSS ==> [0001000000 -
0002695878]
#4 [00026b6000 - 000f7d7600] RAMDISK ==> [00026b6000 -
000f7d7600]
#5 [000f7d8000 - 0010f42000] XEN START INFO ==> [000f7d8000 -
0010f42000]
#6 [0002696000 - 0002696149] BRK ==> [0002696000 -
0002696149]
#7 [0000100000 - 0000670000] PGTABLE ==> [0000100000 -
0000670000]
#8 [0010fcf000 - 0011f40000] PGTABLE ==> [0010fcf000 -
0011f40000]
#9 [0000010000 - 0000016840] MEMNODEMAP ==> [0000010000 -
0000016840]
Bootmem setup node 2 00000001c0000000-00000002ed0cf000
NODE_DATA [00000001c0000000 - 00000001c0017fff]
bootmap [00000001c0018000 - 00000001c003da1f] pages 26
(10 early reservations) ==> bootmem [01c0000000 - 02ed0cf000]
#0 [0000000000 - 0000001000] BIOS data page
#1 [0010f42000 - 0010fcf000] XEN PAGETABLES
#2 [0000006000 - 0000008000] TRAMPOLINE
#3 [0001000000 - 0002695878] TEXT DATA BSS
#4 [00026b6000 - 000f7d7600] RAMDISK
#5 [000f7d8000 - 0010f42000] XEN START INFO
#6 [0002696000 - 0002696149] BRK
#7 [0000100000 - 0000670000] PGTABLE
#8 [0010fcf000 - 0011f40000] PGTABLE
#9 [0000010000 - 0000016840] MEMNODEMAP
found SMP MP-table at [ffff8800000ff780] ff780
Zone PFN ranges:
DMA 0x00000010 -> 0x00001000
DMA32 0x00001000 -> 0x00100000
Normal 0x00100000 -> 0x002ed0cf
Movable zone start PFN for each node
early_node_map[4] active PFN ranges
0: 0x00000010 -> 0x0000009a
0: 0x00000100 -> 0x000bf760
0: 0x00100000 -> 0x001c0000
2: 0x001c0000 -> 0x002ed0cf
On node 0 totalpages: 1570538
DMA zone: 104 pages used for memmap
DMA zone: 1401 pages reserved
DMA zone: 2473 pages, LIFO batch:0
DMA32 zone: 26520 pages used for memmap
DMA32 zone: 753608 pages, LIFO batch:31
Normal zone: 19968 pages used for memmap
Normal zone: 766464 pages, LIFO batch:31
On node 2 totalpages: 1233103
Normal zone: 31310 pages used for memmap
Normal zone: 1201793 pages, LIFO batch:31
ACPI: PM-Timer IO Port: 0x808
ACPI: Local APIC address 0xfee00000
ACPI: LAPIC (acpi_id[0x01] lapic_id[0x00] enabled)
ACPI: LAPIC (acpi_id[0x02] lapic_id[0x10] enabled)
ACPI: LAPIC (acpi_id[0x03] lapic_id[0x02] enabled)
ACPI: LAPIC (acpi_id[0x04] lapic_id[0x12] enabled)
ACPI: LAPIC (acpi_id[0x05] lapic_id[0x04] enabled)
ACPI: LAPIC (acpi_id[0x06] lapic_id[0x14] enabled)
ACPI: LAPIC (acpi_id[0x07] lapic_id[0x06] enabled)
ACPI: LAPIC (acpi_id[0x08] lapic_id[0x16] enabled)
ACPI: LAPIC (acpi_id[0x09] lapic_id[0x01] enabled)
ACPI: LAPIC (acpi_id[0x0a] lapic_id[0x11] enabled)
ACPI: LAPIC (acpi_id[0x0b] lapic_id[0x03] enabled)
ACPI: LAPIC (acpi_id[0x0c] lapic_id[0x13] enabled)
ACPI: LAPIC (acpi_id[0x0d] lapic_id[0x05] enabled)
ACPI: LAPIC (acpi_id[0x0e] lapic_id[0x15] enabled)
ACPI: LAPIC (acpi_id[0x0f] lapic_id[0x07] enabled)
ACPI: LAPIC (acpi_id[0x10] lapic_id[0x17] enabled)
ACPI: LAPIC_NMI (acpi_id[0xff] dfl dfl lint[0x1])
ACPI: IOAPIC (id[0x08] address[0xfec00000] gsi_base[0])
IOAPIC[0]: apic_id 8, version 0, address 0xfec00000, GSI 0-0
ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
ERROR: Unable to locate IOAPIC for GSI 2
ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 20 low level)
ERROR: Unable to locate IOAPIC for GSI 20
Using ACPI (MADT) for SMP configuration information
ACPI: HPET id: 0xffffffff base: 0xfed00000
SMP: Allowing 16 CPUs, 0 hotplug CPUs
nr_irqs_gsi: 256
PM: Registered nosave memory: 000000000009a000 - 0000000000100000
PM: Registered nosave memory: 00000000bf760000 - 00000000bf76e000
PM: Registered nosave memory: 00000000bf76e000 - 00000000bf770000
PM: Registered nosave memory: 00000000bf770000 - 00000000bf77e000
PM: Registered nosave memory: 00000000bf77e000 - 00000000bf7d0000
PM: Registered nosave memory: 00000000bf7d0000 - 00000000bf7e0000
PM: Registered nosave memory: 00000000bf7e0000 - 00000000bf7ec000
PM: Registered nosave memory: 00000000bf7ec000 - 00000000c0000000
PM: Registered nosave memory: 00000000c0000000 - 00000000fec00000
PM: Registered nosave memory: 00000000fec00000 - 00000000fec01000
PM: Registered nosave memory: 00000000fec01000 - 00000000fee00000
PM: Registered nosave memory: 00000000fee00000 - 00000000fee01000
PM: Registered nosave memory: 00000000fee01000 - 00000000ffc00000
PM: Registered nosave memory: 00000000ffc00000 - 0000000100000000
Allocating PCI resources starting at c0000000 (gap: c0000000:3ec00000)
Booting paravirtualized kernel on Xen
Xen version: 4.0.1-rc1 (preserve-AD) (dom0)
NR_CPUS:512 nr_cpumask_bits:512 nr_cpu_ids:16 nr_node_ids:3
PERCPU: Embedded 478 pages/cpu @ffff880032052000 s1927128 r8192 d22568
u1957888
pcpu-alloc: s1927128 r8192 d22568 u1957888 alloc=478*4096
pcpu-alloc: [0] 00 [0] 02 [0] 04 [0] 06 [0] 08 [0] 10 [0] 12 [0] 14
pcpu-alloc: [1] 01 [1] 03 [1] 05 [1] 07 [1] 09 [1] 11 [1] 13 [1] 15
trying to map vcpu_info 0 at ffff88003205d020, mfn 15205d, offset 32
cpu 0 using vcpu_info at ffff88003205d020
trying to map vcpu_info 1 at ffff8801c7c58020, mfn 2e7c58, offset 32
cpu 1 using vcpu_info at ffff8801c7c58020
trying to map vcpu_info 2 at ffff88003223b020, mfn 15223b, offset 32
cpu 2 using vcpu_info at ffff88003223b020
trying to map vcpu_info 3 at ffff8801c7e36020, mfn 2e7e36, offset 32
cpu 3 using vcpu_info at ffff8801c7e36020
trying to map vcpu_info 4 at ffff880032419020, mfn 152419, offset 32
cpu 4 using vcpu_info at ffff880032419020
trying to map vcpu_info 5 at ffff8801c8014020, mfn 2e8014, offset 32
cpu 5 using vcpu_info at ffff8801c8014020
trying to map vcpu_info 6 at ffff8800325f7020, mfn 1525f7, offset 32
cpu 6 using vcpu_info at ffff8800325f7020
trying to map vcpu_info 7 at ffff8801c81f2020, mfn 2e81f2, offset 32
cpu 7 using vcpu_info at ffff8801c81f2020
trying to map vcpu_info 8 at ffff8800327d5020, mfn 1527d5, offset 32
cpu 8 using vcpu_info at ffff8800327d5020
trying to map vcpu_info 9 at ffff8801c83d0020, mfn 2e83d0, offset 32
cpu 9 using vcpu_info at ffff8801c83d0020
trying to map vcpu_info 10 at ffff8800329b3020, mfn 1529b3, offset 32
cpu 10 using vcpu_info at ffff8800329b3020
trying to map vcpu_info 11 at ffff8801c85ae020, mfn 2e85ae, offset 32
cpu 11 using vcpu_info at ffff8801c85ae020
trying to map vcpu_info 12 at ffff880032b91020, mfn 152b91, offset 32
cpu 12 using vcpu_info at ffff880032b91020
trying to map vcpu_info 13 at ffff8801c878c020, mfn 2e878c, offset 32
cpu 13 using vcpu_info at ffff8801c878c020
trying to map vcpu_info 14 at ffff880032d6f020, mfn 152d6f, offset 32
cpu 14 using vcpu_info at ffff880032d6f020
trying to map vcpu_info 15 at ffff8801c896a020, mfn 2e896a, offset 32
cpu 15 using vcpu_info at ffff8801c896a020
Xen: using vcpu_info placement
Built 2 zonelists in Zone order, mobility grouping on. Total pages:
2724338
Policy zone: Normal
Kernel command line: root=/dev/mapper/MISC-fedora ro nomodeset
console=hvc0 earlyprintk=xen debug initcall_debug loglvel=10
PID hash table entries: 4096 (order: 3, 32768 bytes)
Initializing CPU#0
DMA: Placing 64MB software IO TLB between ffff880020000000 -
ffff880024000000
DMA: software IO TLB at phys 0x20000000 - 0x24000000
xen_swiotlb_fixup: buf=ffff880020000000 size=67108864
xen_swiotlb_fixup: buf=ffff880024060000 size=32768
Memory: 10546768k/12272444k available (4727k kernel code, 1057880k
absent, 667796k reserved, 3359k data, 3380k init)
SLUB: Genslabs=14, HWalign=64, Order=0-3, MinObjects=0, CPUs=16, Nodes=3
Hierarchical RCU implementation.
NR_IRQS:4352 nr_irqs:4352
xen: --> irq=0
xen: --> irq=1
xen: --> irq=2
xen: --> irq=3
xen: --> irq=4
xen: --> irq=5
xen: --> irq=6
xen: --> irq=7
xen: --> irq=8
xen: --> irq=9
xen: --> irq=10
xen: --> irq=11
xen: --> irq=12
xen: --> irq=13
xen: --> irq=14
xen: --> irq=15
ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 20 low level)
xen: sci override: source_irq=9 global_irq=20 trigger=c polarity=3
xen: registering gsi 20 triggering 0 polarity 1
alloc irq_desc for 20 on node 0
alloc kstat_irqs on node 0
xen: --> irq=20
xen: acpi sci 20
Console: colour VGA+ 80x25
console [hvc0] enabled, bootconsole disabled
console [hvc0] enabled, bootconsole disabled
Lock dependency validator: Copyright (c) 2006 Red Hat, Inc., Ingo Molnar
... MAX_LOCKDEP_SUBCLASSES: 8
... MAX_LOCK_DEPTH: 48
... MAX_LOCKDEP_KEYS: 8191
... CLASSHASH_SIZE: 4096
... MAX_LOCKDEP_ENTRIES: 16384
... MAX_LOCKDEP_CHAINS: 32768
... CHAINHASH_SIZE: 16384
memory used by lock dependency info: 6367 kB
per task-struct memory footprint: 2688 bytes
allocated 112721920 bytes of page_cgroup
please try ''cgroup_disable=memory'' option if you
don''t want memory
cgroups
ODEBUG: 24 of 24 active objects replaced
Xen: using vcpuop timer interface
installing Xen timer for CPU 0
alloc irq_desc for 4351 on node 0
alloc kstat_irqs on node 0
Detected 2266.784 MHz processor.
Calibrating delay loop (skipped), value calculated using timer
frequency.. 4533.56 BogoMIPS (lpj=2266784)
Security Framework initialized
SELinux: Initializing.
SELinux: Starting in permissive mode
Dentry cache hash table entries: 2097152 (order: 12, 16777216 bytes)
Inode-cache hash table entries: 1048576 (order: 11, 8388608 bytes)
Mount-cache hash table entries: 256
Initializing cgroup subsys ns
Initializing cgroup subsys cpuacct
Initializing cgroup subsys memory
Initializing cgroup subsys devices
Initializing cgroup subsys freezer
Initializing cgroup subsys net_cls
CPU: L1 I cache: 32K, L1 D cache: 32K
CPU: L2 cache: 256K
CPU: L3 cache: 8192K
CPU 0/0x0 -> Node 0
CPU: Physical Processor ID: 0
CPU: Processor Core ID: 0
mce: CPU supports 9 MCE banks
Performance Events: unsupported p6 CPU model 26 no PMU driver, software
events only.
lockdep: fixing up alternatives.
SMP alternatives: switching to UP code
ACPI: Core revision 20090903
ftrace: converting mcount calls to 0f 1f 44 00 00
ftrace: allocating 22950 entries in 91 pages
alloc irq_desc for 4350 on node 0
alloc kstat_irqs on node 0
alloc irq_desc for 4349 on node 0
alloc kstat_irqs on node 0
alloc irq_desc for 4348 on node 0
alloc kstat_irqs on node 0
alloc irq_desc for 4347 on node 0
alloc kstat_irqs on node 0
calling migration_init+0x0/0x59 @ 1
initcall migration_init+0x0/0x59 returned 0 after 976 usecs
calling spawn_ksoftirqd+0x0/0x5a @ 1
initcall spawn_ksoftirqd+0x0/0x5a returned 0 after 976 usecs
calling init_call_single_data+0x0/0xad @ 1
initcall init_call_single_data+0x0/0xad returned 0 after 0 usecs
calling spawn_softlockup_task+0x0/0x75 @ 1
initcall spawn_softlockup_task+0x0/0x75 returned 0 after 976 usecs
calling relay_init+0x0/0x14 @ 1
initcall relay_init+0x0/0x14 returned 0 after 0 usecs
calling tracer_alloc_buffers+0x0/0x218 @ 1
initcall tracer_alloc_buffers+0x0/0x218 returned 0 after 976 usecs
calling init_trace_printk+0x0/0x12 @ 1
initcall init_trace_printk+0x0/0x12 returned 0 after 0 usecs
calling trace_workqueue_early_init+0x0/0x137 @ 1
initcall trace_workqueue_early_init+0x0/0x137 returned 0 after 976 usecs
calling mce_amd_init+0x0/0x33 @ 1
initcall mce_amd_init+0x0/0x33 returned 0 after 0 usecs
installing Xen timer for CPU 1
alloc irq_desc for 4346 on node 0
alloc kstat_irqs on node 0
lockdep: fixing up alternatives.
SMP alternatives: switching to SMP code
alloc irq_desc for 4345 on node 0
alloc kstat_irqs on node 0
alloc irq_desc for 4344 on node 0
alloc kstat_irqs on node 0
alloc irq_desc for 4343 on node 0
alloc kstat_irqs on node 0
alloc irq_desc for 4342 on node 0
alloc kstat_irqs on node 0
Initializing CPU#1
CPU: L1 I cache: 32K, L1 D cache: 32K
CPU: L2 cache: 256K
CPU: L3 cache: 8192K
CPU 1/0x0 -> Node 0
CPU: Physical Processor ID: 1
CPU: Processor Core ID: 0
installing Xen timer for CPU 2
alloc irq_desc for 4341 on node 0
alloc kstat_irqs on node 0
alloc irq_desc for 4340 on node 0
alloc kstat_irqs on node 0
alloc irq_desc for 4339 on node 0
alloc kstat_irqs on node 0
alloc irq_desc for 4338 on node 0
alloc kstat_irqs on node 0
alloc irq_desc for 4337 on node 0
alloc kstat_irqs on node 0
Initializing CPU#2
CPU: L1 I cache: 32K, L1 D cache: 32K
CPU: L2 cache: 256K
CPU: L3 cache: 8192K
CPU 2/0x0 -> Node 0
CPU: Physical Processor ID: 0
CPU: Processor Core ID: 1
installing Xen timer for CPU 3
alloc irq_desc for 4336 on node 0
alloc kstat_irqs on node 0
alloc irq_desc for 4335 on node 0
alloc kstat_irqs on node 0
alloc irq_desc for 4334 on node 0
alloc kstat_irqs on node 0
alloc irq_desc for 4333 on node 0
alloc kstat_irqs on node 0
alloc irq_desc for 4332 on node 0
alloc kstat_irqs on node 0
Initializing CPU#3
CPU: L1 I cache: 32K, L1 D cache: 32K
CPU: L2 cache: 256K
CPU: L3 cache: 8192K
CPU 3/0x0 -> Node 0
CPU: Physical Processor ID: 1
CPU: Processor Core ID: 1
installing Xen timer for CPU 4
alloc irq_desc for 4331 on node 0
alloc kstat_irqs on node 0
alloc irq_desc for 4330 on node 0
alloc kstat_irqs on node 0
alloc irq_desc for 4329 on node 0
alloc kstat_irqs on node 0
alloc irq_desc for 4328 on node 0
alloc kstat_irqs on node 0
alloc irq_desc for 4327 on node 0
alloc kstat_irqs on node 0
Initializing CPU#4
CPU: L1 I cache: 32K, L1 D cache: 32K
CPU: L2 cache: 256K
CPU: L3 cache: 8192K
CPU 4/0x0 -> Node 0
CPU: Physical Processor ID: 0
CPU: Processor Core ID: 2
installing Xen timer for CPU 5
alloc irq_desc for 4326 on node 0
alloc kstat_irqs on node 0
alloc irq_desc for 4325 on node 0
alloc kstat_irqs on node 0
alloc irq_desc for 4324 on node 0
alloc kstat_irqs on node 0
alloc irq_desc for 4323 on node 0
alloc kstat_irqs on node 0
alloc irq_desc for 4322 on node 0
alloc kstat_irqs on node 0
Initializing CPU#5
CPU: L1 I cache: 32K, L1 D cache: 32K
CPU: L2 cache: 256K
CPU: L3 cache: 8192K
CPU 5/0x0 -> Node 0
CPU: Physical Processor ID: 1
CPU: Processor Core ID: 2
installing Xen timer for CPU 6
alloc irq_desc for 4321 on node 0
alloc kstat_irqs on node 0
alloc irq_desc for 4320 on node 0
alloc kstat_irqs on node 0
alloc irq_desc for 4319 on node 0
alloc kstat_irqs on node 0
alloc irq_desc for 4318 on node 0
alloc kstat_irqs on node 0
alloc irq_desc for 4317 on node 0
alloc kstat_irqs on node 0
Initializing CPU#6
CPU: L1 I cache: 32K, L1 D cache: 32K
CPU: L2 cache: 256K
CPU: L3 cache: 8192K
CPU 6/0x0 -> Node 0
CPU: Physical Processor ID: 0
CPU: Processor Core ID: 3
installing Xen timer for CPU 7
alloc irq_desc for 4316 on node 0
alloc kstat_irqs on node 0
alloc irq_desc for 4315 on node 0
alloc kstat_irqs on node 0
alloc irq_desc for 4314 on node 0
alloc kstat_irqs on node 0
alloc irq_desc for 4313 on node 0
alloc kstat_irqs on node 0
alloc irq_desc for 4312 on node 0
alloc kstat_irqs on node 0
Initializing CPU#7
CPU: L1 I cache: 32K, L1 D cache: 32K
CPU: L2 cache: 256K
CPU: L3 cache: 8192K
CPU 7/0x0 -> Node 0
CPU: Physical Processor ID: 1
CPU: Processor Core ID: 3
installing Xen timer for CPU 8
alloc irq_desc for 4311 on node 0
alloc kstat_irqs on node 0
alloc irq_desc for 4310 on node 0
alloc kstat_irqs on node 0
alloc irq_desc for 4309 on node 0
alloc kstat_irqs on node 0
alloc irq_desc for 4308 on node 0
alloc kstat_irqs on node 0
alloc irq_desc for 4307 on node 0
alloc kstat_irqs on node 0
Initializing CPU#8
CPU: L1 I cache: 32K, L1 D cache: 32K
CPU: L2 cache: 256K
CPU: L3 cache: 8192K
CPU 8/0x0 -> Node 0
CPU: Physical Processor ID: 0
CPU: Processor Core ID: 0
installing Xen timer for CPU 9
alloc irq_desc for 4306 on node 0
alloc kstat_irqs on node 0
alloc irq_desc for 4305 on node 0
alloc kstat_irqs on node 0
alloc irq_desc for 4304 on node 0
alloc kstat_irqs on node 0
alloc irq_desc for 4303 on node 0
alloc kstat_irqs on node 0
alloc irq_desc for 4302 on node 0
alloc kstat_irqs on node 0
Initializing CPU#9
CPU: L1 I cache: 32K, L1 D cache: 32K
CPU: L2 cache: 256K
CPU: L3 cache: 8192K
CPU 9/0x0 -> Node 0
CPU: Physical Processor ID: 1
CPU: Processor Core ID: 0
installing Xen timer for CPU 10
alloc irq_desc for 4301 on node 0
alloc kstat_irqs on node 0
alloc irq_desc for 4300 on node 0
alloc kstat_irqs on node 0
alloc irq_desc for 4299 on node 0
alloc kstat_irqs on node 0
alloc irq_desc for 4298 on node 0
alloc kstat_irqs on node 0
alloc irq_desc for 4297 on node 0
alloc kstat_irqs on node 0
Initializing CPU#10
CPU: L1 I cache: 32K, L1 D cache: 32K
CPU: L2 cache: 256K
CPU: L3 cache: 8192K
CPU 10/0x0 -> Node 0
CPU: Physical Processor ID: 0
CPU: Processor Core ID: 1
installing Xen timer for CPU 11
alloc irq_desc for 4296 on node 0
alloc kstat_irqs on node 0
alloc irq_desc for 4295 on node 0
alloc kstat_irqs on node 0
alloc irq_desc for 4294 on node 0
alloc kstat_irqs on node 0
alloc irq_desc for 4293 on node 0
alloc kstat_irqs on node 0
alloc irq_desc for 4292 on node 0
alloc kstat_irqs on node 0
Initializing CPU#11
CPU: L1 I cache: 32K, L1 D cache: 32K
CPU: L2 cache: 256K
CPU: L3 cache: 8192K
CPU 11/0x0 -> Node 0
CPU: Physical Processor ID: 1
CPU: Processor Core ID: 1
installing Xen timer for CPU 12
alloc irq_desc for 4291 on node 0
alloc kstat_irqs on node 0
alloc irq_desc for 4290 on node 0
alloc kstat_irqs on node 0
alloc irq_desc for 4289 on node 0
alloc kstat_irqs on node 0
alloc irq_desc for 4288 on node 0
alloc kstat_irqs on node 0
alloc irq_desc for 4287 on node 0
alloc kstat_irqs on node 0
Initializing CPU#12
CPU: L1 I cache: 32K, L1 D cache: 32K
CPU: L2 cache: 256K
CPU: L3 cache: 8192K
CPU 12/0x0 -> Node 0
CPU: Physical Processor ID: 0
CPU: Processor Core ID: 2
installing Xen timer for CPU 13
alloc irq_desc for 4286 on node 0
alloc kstat_irqs on node 0
alloc irq_desc for 4285 on node 0
alloc kstat_irqs on node 0
alloc irq_desc for 4284 on node 0
alloc kstat_irqs on node 0
alloc irq_desc for 4283 on node 0
alloc kstat_irqs on node 0
alloc irq_desc for 4282 on node 0
alloc kstat_irqs on node 0
Initializing CPU#13
CPU: L1 I cache: 32K, L1 D cache: 32K
CPU: L2 cache: 256K
CPU: L3 cache: 8192K
CPU 13/0x0 -> Node 0
CPU: Physical Processor ID: 1
CPU: Processor Core ID: 2
installing Xen timer for CPU 14
alloc irq_desc for 4281 on node 0
alloc kstat_irqs on node 0
alloc irq_desc for 4280 on node 0
alloc kstat_irqs on node 0
alloc irq_desc for 4279 on node 0
alloc kstat_irqs on node 0
alloc irq_desc for 4278 on node 0
alloc kstat_irqs on node 0
alloc irq_desc for 4277 on node 0
alloc kstat_irqs on node 0
Initializing CPU#14
CPU: L1 I cache: 32K, L1 D cache: 32K
CPU: L2 cache: 256K
CPU: L3 cache: 8192K
CPU 14/0x0 -> Node 0
CPU: Physical Processor ID: 0
CPU: Processor Core ID: 3
installing Xen timer for CPU 15
alloc irq_desc for 4276 on node 0
alloc kstat_irqs on node 0
alloc irq_desc for 4275 on node 0
alloc kstat_irqs on node 0
alloc irq_desc for 4274 on node 0
alloc kstat_irqs on node 0
alloc irq_desc for 4273 on node 0
alloc kstat_irqs on node 0
alloc irq_desc for 4272 on node 0
alloc kstat_irqs on node 0
Initializing CPU#15
CPU: L1 I cache: 32K, L1 D cache: 32K
CPU: L2 cache: 256K
CPU: L3 cache: 8192K
CPU 15/0x0 -> Node 0
CPU: Physical Processor ID: 1
CPU: Processor Core ID: 3
Brought up 16 CPUs
CPU0 attaching sched-domain:
domain 0: span 0,8 level SIBLING
groups: 0 (cpu_power = 589) 8 (cpu_power = 589)
domain 1: span 0,8 level MC
groups: 0,8 (cpu_power = 1178)
domain 2: span 0-15 level CPU
groups: 0,8 (cpu_power = 1178) 1,9 (cpu_power = 1178) 2,10
(cpu_power = 1178) 3,11 (cpu_power = 1178) 4,12 (cpu_power = 1178) 5,13
(cpu_power = 1178) 6,14 (cpu_power = 1178) 7,15 (cpu_power = 1178)
domain 3: span 0-15 level NODE
groups: 0-15 (cpu_power = 9424)
CPU1 attaching sched-domain:
domain 0: span 1,9 level SIBLING
groups: 1 (cpu_power = 589) 9 (cpu_power = 589)
domain 1: span 1,9 level MC
groups: 1,9 (cpu_power = 1178)
domain 2: span 0-15 level CPU
groups: 1,9 (cpu_power = 1178) 2,10 (cpu_power = 1178) 3,11
(cpu_power = 1178) 4,12 (cpu_power = 1178) 5,13 (cpu_power = 1178) 6,14
(cpu_power = 1178) 7,15 (cpu_power = 1178) 0,8 (cpu_power = 1178)
domain 3: span 0-15 level NODE
groups: 0-15 (cpu_power = 9424)
CPU2 attaching sched-domain:
domain 0: span 2,10 level SIBLING
groups: 2 (cpu_power = 589) 10 (cpu_power = 589)
domain 1: span 2,10 level MC
groups: 2,10 (cpu_power = 1178)
domain 2: span 0-15 level CPU
groups: 2,10 (cpu_power = 1178) 3,11 (cpu_power = 1178) 4,12
(cpu_power = 1178) 5,13 (cpu_power = 1178) 6,14 (cpu_power = 1178) 7,15
(cpu_power = 1178) 0,8 (cpu_power = 1178) 1,9 (cpu_power = 1178)
domain 3: span 0-15 level NODE
groups: 0-15 (cpu_power = 9424)
CPU3 attaching sched-domain:
domain 0: span 3,11 level SIBLING
groups: 3 (cpu_power = 589) 11 (cpu_power = 589)
domain 1: span 3,11 level MC
groups: 3,11 (cpu_power = 1178)
domain 2: span 0-15 level CPU
groups: 3,11 (cpu_power = 1178) 4,12 (cpu_power = 1178) 5,13
(cpu_power = 1178) 6,14 (cpu_power = 1178) 7,15 (cpu_power = 1178) 0,8
(cpu_power = 1178) 1,9 (cpu_power = 1178) 2,10 (cpu_power = 1178)
domain 3: span 0-15 level NODE
groups: 0-15 (cpu_power = 9424)
CPU4 attaching sched-domain:
domain 0: span 4,12 level SIBLING
groups: 4 (cpu_power = 589) 12 (cpu_power = 589)
domain 1: span 4,12 level MC
groups: 4,12 (cpu_power = 1178)
domain 2: span 0-15 level CPU
groups: 4,12 (cpu_power = 1178) 5,13 (cpu_power = 1178) 6,14
(cpu_power = 1178) 7,15 (cpu_power = 1178) 0,8 (cpu_power = 1178) 1,9
(cpu_power = 1178) 2,10 (cpu_power = 1178) 3,11 (cpu_power = 1178)
domain 3: span 0-15 level NODE
groups: 0-15 (cpu_power = 9424)
CPU5 attaching sched-domain:
domain 0: span 5,13 level SIBLING
groups: 5 (cpu_power = 589) 13 (cpu_power = 589)
domain 1: span 5,13 level MC
groups: 5,13 (cpu_power = 1178)
domain 2: span 0-15 level CPU
groups: 5,13 (cpu_power = 1178) 6,14 (cpu_power = 1178) 7,15
(cpu_power = 1178) 0,8 (cpu_power = 1178) 1,9 (cpu_power = 1178) 2,10
(cpu_power = 1178) 3,11 (cpu_power = 1178) 4,12 (cpu_power = 1178)
domain 3: span 0-15 level NODE
groups: 0-15 (cpu_power = 9424)
CPU6 attaching sched-domain:
domain 0: span 6,14 level SIBLING
groups: 6 (cpu_power = 589) 14 (cpu_power = 589)
domain 1: span 6,14 level MC
groups: 6,14 (cpu_power = 1178)
domain 2: span 0-15 level CPU
groups: 6,14 (cpu_power = 1178) 7,15 (cpu_power = 1178) 0,8
(cpu_power = 1178) 1,9 (cpu_power = 1178) 2,10 (cpu_power = 1178) 3,11
(cpu_power = 1178) 4,12 (cpu_power = 1178) 5,13 (cpu_power = 1178)
domain 3: span 0-15 level NODE
groups: 0-15 (cpu_power = 9424)
CPU7 attaching sched-domain:
domain 0: span 7,15 level SIBLING
groups: 7 (cpu_power = 589) 15 (cpu_power = 589)
domain 1: span 7,15 level MC
groups: 7,15 (cpu_power = 1178)
domain 2: span 0-15 level CPU
groups: 7,15 (cpu_power = 1178) 0,8 (cpu_power = 1178) 1,9
(cpu_power = 1178) 2,10 (cpu_power = 1178) 3,11 (cpu_power = 1178) 4,12
(cpu_power = 1178) 5,13 (cpu_power = 1178) 6,14 (cpu_power = 1178)
domain 3: span 0-15 level NODE
groups: 0-15 (cpu_power = 9424)
CPU8 attaching sched-domain:
domain 0: span 0,8 level SIBLING
groups: 8 (cpu_power = 589) 0 (cpu_power = 589)
domain 1: span 0,8 level MC
groups: 0,8 (cpu_power = 1178)
domain 2: span 0-15 level CPU
groups: 0,8 (cpu_power = 1178) 1,9 (cpu_power = 1178) 2,10
(cpu_power = 1178) 3,11 (cpu_power = 1178) 4,12 (cpu_power = 1178) 5,13
(cpu_power = 1178) 6,14 (cpu_power = 1178) 7,15 (cpu_power = 1178)
domain 3: span 0-15 level NODE
groups: 0-15 (cpu_power = 9424)
CPU9 attaching sched-domain:
domain 0: span 1,9 level SIBLING
groups: 9 (cpu_power = 589) 1 (cpu_power = 589)
domain 1: span 1,9 level MC
groups: 1,9 (cpu_power = 1178)
domain 2: span 0-15 level CPU
groups: 1,9 (cpu_power = 1178) 2,10 (cpu_power = 1178) 3,11
(cpu_power = 1178) 4,12 (cpu_power = 1178) 5,13 (cpu_power = 1178) 6,14
(cpu_power = 1178) 7,15 (cpu_power = 1178) 0,8 (cpu_power = 1178)
domain 3: span 0-15 level NODE
groups: 0-15 (cpu_power = 9424)
CPU10 attaching sched-domain:
domain 0: span 2,10 level SIBLING
groups: 10 (cpu_power = 589) 2 (cpu_power = 589)
domain 1: span 2,10 level MC
groups: 2,10 (cpu_power = 1178)
domain 2: span 0-15 level CPU
groups: 2,10 (cpu_power = 1178) 3,11 (cpu_power = 1178) 4,12
(cpu_power = 1178) 5,13 (cpu_power = 1178) 6,14 (cpu_power = 1178) 7,15
(cpu_power = 1178) 0,8 (cpu_power = 1178) 1,9 (cpu_power = 1178)
domain 3: span 0-15 level NODE
groups: 0-15 (cpu_power = 9424)
CPU11 attaching sched-domain:
domain 0: span 3,11 level SIBLING
groups: 11 (cpu_power = 589) 3 (cpu_power = 589)
domain 1: span 3,11 level MC
groups: 3,11 (cpu_power = 1178)
domain 2: span 0-15 level CPU
groups: 3,11 (cpu_power = 1178) 4,12 (cpu_power = 1178) 5,13
(cpu_power = 1178) 6,14 (cpu_power = 1178) 7,15 (cpu_power = 1178) 0,8
(cpu_power = 1178) 1,9 (cpu_power = 1178) 2,10 (cpu_power = 1178)
domain 3: span 0-15 level NODE
groups: 0-15 (cpu_power = 9424)
CPU12 attaching sched-domain:
domain 0: span 4,12 level SIBLING
groups: 12 (cpu_power = 589) 4 (cpu_power = 589)
domain 1: span 4,12 level MC
groups: 4,12 (cpu_power = 1178)
domain 2: span 0-15 level CPU
groups: 4,12 (cpu_power = 1178) 5,13 (cpu_power = 1178) 6,14
(cpu_power = 1178) 7,15 (cpu_power = 1178) 0,8 (cpu_power = 1178) 1,9
(cpu_power = 1178) 2,10 (cpu_power = 1178) 3,11 (cpu_power = 1178)
domain 3: span 0-15 level NODE
groups: 0-15 (cpu_power = 9424)
CPU13 attaching sched-domain:
domain 0: span 5,13 level SIBLING
groups: 13 (cpu_power = 589) 5 (cpu_power = 589)
domain 1: span 5,13 level MC
groups: 5,13 (cpu_power = 1178)
domain 2: span 0-15 level CPU
groups: 5,13 (cpu_power = 1178) 6,14 (cpu_power = 1178) 7,15
(cpu_power = 1178) 0,8 (cpu_power = 1178) 1,9 (cpu_power = 1178) 2,10
(cpu_power = 1178) 3,11 (cpu_power = 1178) 4,12 (cpu_power = 1178)
domain 3: span 0-15 level NODE
groups: 0-15 (cpu_power = 9424)
CPU14 attaching sched-domain:
domain 0: span 6,14 level SIBLING
groups: 14 (cpu_power = 589) 6 (cpu_power = 589)
domain 1: span 6,14 level MC
groups: 6,14 (cpu_power = 1178)
domain 2: span 0-15 level CPU
groups: 6,14 (cpu_power = 1178) 7,15 (cpu_power = 1178) 0,8
(cpu_power = 1178) 1,9 (cpu_power = 1178) 2,10 (cpu_power = 1178) 3,11
(cpu_power = 1178) 4,12 (cpu_power = 1178) 5,13 (cpu_power = 1178)
domain 3: span 0-15 level NODE
groups: 0-15 (cpu_power = 9424)
CPU15 attaching sched-domain:
domain 0: span 7,15 level SIBLING
groups: 15 (cpu_power = 589) 7 (cpu_power = 589)
domain 1: span 7,15 level MC
groups: 7,15 (cpu_power = 1178)
domain 2: span 0-15 level CPU
groups: 7,15 (cpu_power = 1178) 0,8 (cpu_power = 1178) 1,9
(cpu_power = 1178) 2,10 (cpu_power = 1178) 3,11 (cpu_power = 1178) 4,12
(cpu_power = 1178) 5,13 (cpu_power = 1178) 6,14 (cpu_power = 1178)
domain 3: span 0-15 level NODE
groups: 0-15 (cpu_power = 9424)
calling init_mmap_min_addr+0x0/0x26 @ 1
initcall init_mmap_min_addr+0x0/0x26 returned 0 after 0 usecs
calling init_cpufreq_transition_notifier_list+0x0/0x1b @ 1
initcall init_cpufreq_transition_notifier_list+0x0/0x1b returned 0 after
0 usecs
calling net_ns_init+0x0/0xf8 @ 1
initcall net_ns_init+0x0/0xf8 returned 0 after 976 usecs
calling e820_mark_nvs_memory+0x0/0x40 @ 1
initcall e820_mark_nvs_memory+0x0/0x40 returned 0 after 976 usecs
calling cpufreq_tsc+0x0/0x28 @ 1
initcall cpufreq_tsc+0x0/0x28 returned 0 after 0 usecs
calling pci_reboot_init+0x0/0x14 @ 1
initcall pci_reboot_init+0x0/0x14 returned 0 after 0 usecs
calling init_lapic_sysfs+0x0/0x2d @ 1
initcall init_lapic_sysfs+0x0/0x2d returned 0 after 0 usecs
calling alloc_frozen_cpus+0x0/0xd @ 1
initcall alloc_frozen_cpus+0x0/0xd returned 0 after 0 usecs
calling sysctl_init+0x0/0x32 @ 1
initcall sysctl_init+0x0/0x32 returned 0 after 976 usecs
calling ksysfs_init+0x0/0xbb @ 1
initcall ksysfs_init+0x0/0xbb returned 0 after 0 usecs
calling async_init+0x0/0x60 @ 1
initcall async_init+0x0/0x60 returned 0 after 976 usecs
calling init_jiffies_clocksource+0x0/0x12 @ 1
initcall init_jiffies_clocksource+0x0/0x12 returned 0 after 0 usecs
calling pm_init+0x0/0x34 @ 1
initcall pm_init+0x0/0x34 returned 0 after 0 usecs
calling pm_disk_init+0x0/0x19 @ 1
initcall pm_disk_init+0x0/0x19 returned 0 after 0 usecs
calling swsusp_header_init+0x0/0x31 @ 1
initcall swsusp_header_init+0x0/0x31 returned 0 after 0 usecs
calling init_zero_pfn+0x0/0x35 @ 1
initcall init_zero_pfn+0x0/0x35 returned 0 after 0 usecs
calling filelock_init+0x0/0x2e @ 1
initcall filelock_init+0x0/0x2e returned 0 after 976 usecs
calling init_misc_binfmt+0x0/0x42 @ 1
initcall init_misc_binfmt+0x0/0x42 returned 0 after 0 usecs
calling init_script_binfmt+0x0/0x14 @ 1
initcall init_script_binfmt+0x0/0x14 returned 0 after 0 usecs
calling init_elf_binfmt+0x0/0x14 @ 1
initcall init_elf_binfmt+0x0/0x14 returned 0 after 0 usecs
calling init_compat_elf_binfmt+0x0/0x14 @ 1
initcall init_compat_elf_binfmt+0x0/0x14 returned 0 after 0 usecs
calling debugfs_init+0x0/0x5a @ 1
initcall debugfs_init+0x0/0x5a returned 0 after 0 usecs
calling securityfs_init+0x0/0x51 @ 1
initcall securityfs_init+0x0/0x51 returned 0 after 0 usecs
calling random32_init+0x0/0xd7 @ 1
initcall random32_init+0x0/0xd7 returned 0 after 0 usecs
calling __gnttab_init+0x0/0x26 @ 1
Grant table initialized
initcall __gnttab_init+0x0/0x26 returned 0 after 976 usecs
calling regulator_init+0x0/0x2e @ 1
regulator: core version 0.5
initcall regulator_init+0x0/0x2e returned 0 after 0 usecs
calling early_resume_init+0x0/0x19d @ 1
Time: 11:17:44 Date: 05/30/10
initcall early_resume_init+0x0/0x19d returned 0 after 0 usecs
calling cpufreq_core_init+0x0/0xa2 @ 1
initcall cpufreq_core_init+0x0/0xa2 returned 0 after 0 usecs
calling cpuidle_init+0x0/0x40 @ 1
initcall cpuidle_init+0x0/0x40 returned 0 after 976 usecs
calling sock_init+0x0/0x5e @ 1
initcall sock_init+0x0/0x5e returned 0 after 976 usecs
calling net_inuse_init+0x0/0x26 @ 1
initcall net_inuse_init+0x0/0x26 returned 0 after 0 usecs
calling netpoll_init+0x0/0x41 @ 1
initcall netpoll_init+0x0/0x41 returned 0 after 0 usecs
calling netlink_proto_init+0x0/0x142 @ 1
NET: Registered protocol family 16
initcall netlink_proto_init+0x0/0x142 returned 0 after 976 usecs
calling bdi_class_init+0x0/0x41 @ 1
initcall bdi_class_init+0x0/0x41 returned 0 after 976 usecs
calling kobject_uevent_init+0x0/0x54 @ 1
initcall kobject_uevent_init+0x0/0x54 returned 0 after 976 usecs
calling pcibus_class_init+0x0/0x19 @ 1
initcall pcibus_class_init+0x0/0x19 returned 0 after 976 usecs
calling pci_driver_init+0x0/0x12 @ 1
initcall pci_driver_init+0x0/0x12 returned 0 after 976 usecs
calling backlight_class_init+0x0/0x5d @ 1
initcall backlight_class_init+0x0/0x5d returned 0 after 0 usecs
calling __xenbus_probe_init+0x0/0x21 @ 1
alloc irq_desc for 4271 on node 0
alloc kstat_irqs on node 0
initcall __xenbus_probe_init+0x0/0x21 returned 0 after 1952 usecs
calling tty_class_init+0x0/0x38 @ 1
initcall tty_class_init+0x0/0x38 returned 0 after 0 usecs
calling vtconsole_class_init+0x0/0xc3 @ 1
initcall vtconsole_class_init+0x0/0xc3 returned 0 after 976 usecs
calling register_node_type+0x0/0x7e @ 1
initcall register_node_type+0x0/0x7e returned 0 after 976 usecs
calling amd_postcore_init+0x0/0x78 @ 1
initcall amd_postcore_init+0x0/0x78 returned 0 after 0 usecs
calling arch_kdebugfs_init+0x0/0x272 @ 1
initcall arch_kdebugfs_init+0x0/0x272 returned 0 after 0 usecs
calling mtrr_if_init+0x0/0x63 @ 1
initcall mtrr_if_init+0x0/0x63 returned 0 after 0 usecs
calling ffh_cstate_init+0x0/0x2a @ 1
initcall ffh_cstate_init+0x0/0x2a returned 0 after 0 usecs
calling arch_init_ftrace_syscalls+0x0/0x11e @ 1
initcall arch_init_ftrace_syscalls+0x0/0x11e returned 0 after 976 usecs
calling acpi_pci_init+0x0/0x5c @ 1
ACPI: bus type pci registered
initcall acpi_pci_init+0x0/0x5c returned 0 after 0 usecs
calling register_xen_pci_notifier+0x0/0x24 @ 1
initcall register_xen_pci_notifier+0x0/0x24 returned 0 after 0 usecs
calling setup_vcpu_hotplug_event+0x0/0x22 @ 1
initcall setup_vcpu_hotplug_event+0x0/0x22 returned 0 after 0 usecs
calling dmi_id_init+0x0/0x34c @ 1
initcall dmi_id_init+0x0/0x34c returned 0 after 976 usecs
calling dma_bus_init+0x0/0x3f @ 1
initcall dma_bus_init+0x0/0x3f returned 0 after 0 usecs
calling dma_channel_table_init+0x0/0x10e @ 1
initcall dma_channel_table_init+0x0/0x10e returned 0 after 0 usecs
calling pci_arch_init+0x0/0x60 @ 1
PCI: MCFG configuration 0: base e0000000 segment 0 buses 0 - 255
PCI: Not using MMCONFIG.
PCI: Using configuration type 1 for base access
initcall pci_arch_init+0x0/0x60 returned 0 after 0 usecs
calling topology_init+0x0/0x97 @ 1
initcall topology_init+0x0/0x97 returned 0 after 976 usecs
calling mtrr_init_finialize+0x0/0x3d @ 1
initcall mtrr_init_finialize+0x0/0x3d returned 0 after 0 usecs
calling param_sysfs_init+0x0/0x23a @ 1
initcall param_sysfs_init+0x0/0x23a returned 0 after 7811 usecs
calling pm_sysrq_init+0x0/0x1e @ 1
initcall pm_sysrq_init+0x0/0x1e returned 0 after 0 usecs
calling audit_watch_init+0x0/0x2f @ 1
initcall audit_watch_init+0x0/0x2f returned 0 after 0 usecs
calling init_slow_work+0x0/0x37 @ 1
initcall init_slow_work+0x0/0x37 returned 0 after 0 usecs
calling default_bdi_init+0x0/0xc6 @ 1
initcall default_bdi_init+0x0/0xc6 returned 0 after 976 usecs
calling init_bio+0x0/0xce @ 1
bio: create slab <bio-0> at 0
initcall init_bio+0x0/0xce returned 0 after 3905 usecs
calling fsnotify_init+0x0/0x12 @ 1
initcall fsnotify_init+0x0/0x12 returned 0 after 0 usecs
calling fsnotify_notification_init+0x0/0x100 @ 1
initcall fsnotify_notification_init+0x0/0x100 returned 0 after 976 usecs
calling cryptomgr_init+0x0/0x12 @ 1
initcall cryptomgr_init+0x0/0x12 returned 0 after 0 usecs
calling blk_settings_init+0x0/0x2a @ 1
initcall blk_settings_init+0x0/0x2a returned 0 after 0 usecs
calling blk_ioc_init+0x0/0x2a @ 1
initcall blk_ioc_init+0x0/0x2a returned 0 after 0 usecs
calling blk_softirq_init+0x0/0x70 @ 1
initcall blk_softirq_init+0x0/0x70 returned 0 after 0 usecs
calling blk_iopoll_setup+0x0/0x70 @ 1
initcall blk_iopoll_setup+0x0/0x70 returned 0 after 0 usecs
calling genhd_device_init+0x0/0x7b @ 1
initcall genhd_device_init+0x0/0x7b returned 0 after 2929 usecs
calling blk_dev_integrity_init+0x0/0x2a @ 1
initcall blk_dev_integrity_init+0x0/0x2a returned 0 after 0 usecs
calling pci_slot_init+0x0/0x4c @ 1
initcall pci_slot_init+0x0/0x4c returned 0 after 0 usecs
calling fbmem_init+0x0/0x98 @ 1
initcall fbmem_init+0x0/0x98 returned 0 after 0 usecs
calling acpi_init+0x0/0x2d1 @ 1
ERROR: Unable to locate IOAPIC for GSI 20
ACPI: EC: Look up EC in DSDT
ACPI Warning for \_SB_._OSC: Return type mismatch - found Integer,
expected Buffer (20090903/nspredef-1006)
\_SB_:_OSC evaluation returned wrong type
_OSC request data:1 6
ACPI: Executed 1 blocks of module-level executable AML code
ACPI: Interpreter enabled
ACPI: (supports S0 S1 S4 S5)
ACPI: Using IOAPIC for interrupt routing
PCI: MCFG configuration 0: base e0000000 segment 0 buses 0 - 255
PCI: MCFG area at e0000000 reserved in ACPI motherboard resources
PCI: Using MMCONFIG at e0000000 - efffffff
ACPI Warning: Incorrect checksum in table [OEMB] - 54, should be 51
(20090903/tbutils-314)
ACPI Warning: Incorrect checksum in table [ ] - 50, should be 94
(20090903/tbutils-314)
initcall acpi_init+0x0/0x2d1 returned 0 after 158183 usecs
calling dock_init+0x0/0x8d @ 1
ACPI: No dock devices found.
initcall dock_init+0x0/0x8d returned 0 after 0 usecs
calling acpi_pci_root_init+0x0/0x28 @ 1
ACPI: PCI Root Bridge [PCI0] (0000:00)
pci 0000:00:00.0: PME# supported from D0 D3hot D3cold
pci 0000:00:00.0: PME# disabled
pci 0000:00:01.0: PME# supported from D0 D3hot D3cold
pci 0000:00:01.0: PME# disabled
pci 0000:00:03.0: PME# supported from D0 D3hot D3cold
pci 0000:00:03.0: PME# disabled
pci 0000:00:07.0: PME# supported from D0 D3hot D3cold
pci 0000:00:07.0: PME# disabled
pci 0000:00:16.0: reg 10 64bit mmio: [0xfbbfc000-0xfbbfffff]
pci 0000:00:16.1: reg 10 64bit mmio: [0xfbbf8000-0xfbbfbfff]
pci 0000:00:16.2: reg 10 64bit mmio: [0xfbbf4000-0xfbbf7fff]
pci 0000:00:16.3: reg 10 64bit mmio: [0xfbbf0000-0xfbbf3fff]
pci 0000:00:16.4: reg 10 64bit mmio: [0xfbbec000-0xfbbeffff]
pci 0000:00:16.5: reg 10 64bit mmio: [0xfbbe8000-0xfbbebfff]
pci 0000:00:16.6: reg 10 64bit mmio: [0xfbbe4000-0xfbbe7fff]
pci 0000:00:16.7: reg 10 64bit mmio: [0xfbbe0000-0xfbbe3fff]
pci 0000:00:1a.0: reg 20 io port: [0xac00-0xac1f]
pci 0000:00:1a.1: reg 20 io port: [0xa880-0xa89f]
pci 0000:00:1a.2: reg 20 io port: [0xa800-0xa81f]
pci 0000:00:1a.7: reg 10 32bit mmio: [0xfbbde000-0xfbbde3ff]
pci 0000:00:1a.7: PME# supported from D0 D3hot D3cold
pci 0000:00:1a.7: PME# disabled
pci 0000:00:1b.0: reg 10 64bit mmio: [0xfbbd8000-0xfbbdbfff]
pci 0000:00:1b.0: PME# supported from D0 D3hot D3cold
pci 0000:00:1b.0: PME# disabled
pci 0000:00:1c.0: PME# supported from D0 D3hot D3cold
pci 0000:00:1c.0: PME# disabled
pci 0000:00:1c.4: PME# supported from D0 D3hot D3cold
pci 0000:00:1c.4: PME# disabled
pci 0000:00:1c.5: PME# supported from D0 D3hot D3cold
pci 0000:00:1c.5: PME# disabled
pci 0000:00:1d.0: reg 20 io port: [0xa480-0xa49f]
pci 0000:00:1d.1: reg 20 io port: [0xa400-0xa41f]
pci 0000:00:1d.2: reg 20 io port: [0xa080-0xa09f]
pci 0000:00:1d.7: reg 10 32bit mmio: [0xfbbdc000-0xfbbdc3ff]
pci 0000:00:1d.7: PME# supported from D0 D3hot D3cold
pci 0000:00:1d.7: PME# disabled
pci 0000:00:1f.0: quirk: region 0800-087f claimed by ICH6 ACPI/GPIO/TCO
pci 0000:00:1f.0: quirk: region 0500-053f claimed by ICH6 GPIO
pci 0000:00:1f.0: ICH7 LPC Generic IO decode 1 PIO at 0a00 (mask 00ff)
pci 0000:00:1f.0: ICH7 LPC Generic IO decode 3 PIO at 0290 (mask 0097)
pci 0000:00:1f.2: reg 10 io port: [0xa000-0xa007]
pci 0000:00:1f.2: reg 14 io port: [0x9c00-0x9c03]
pci 0000:00:1f.2: reg 18 io port: [0x9880-0x9887]
pci 0000:00:1f.2: reg 1c io port: [0x9800-0x9803]
pci 0000:00:1f.2: reg 20 io port: [0x9480-0x949f]
pci 0000:00:1f.2: reg 24 32bit mmio: [0xfbbd6000-0xfbbd67ff]
pci 0000:00:1f.2: PME# supported from D3hot
pci 0000:00:1f.2: PME# disabled
pci 0000:00:1f.3: reg 10 64bit mmio: [0xfbbd4000-0xfbbd40ff]
pci 0000:00:1f.3: reg 20 io port: [0x400-0x41f]
pci 0000:01:00.0: reg 10 32bit mmio: [0xf6000000-0xf6ffffff]
pci 0000:01:00.0: reg 14 64bit mmio pref: [0xc0000000-0xcfffffff]
pci 0000:01:00.0: reg 1c 64bit mmio: [0xf4000000-0xf5ffffff]
pci 0000:01:00.0: reg 24 io port: [0xbc00-0xbc7f]
pci 0000:01:00.0: reg 30 32bit mmio pref: [0xf3fe0000-0xf3ffffff]
pci 0000:00:01.0: bridge io port: [0xb000-0xbfff]
pci 0000:00:01.0: bridge 32bit mmio: [0xf3f00000-0xf6ffffff]
pci 0000:00:01.0: bridge 64bit mmio pref: [0xc0000000-0xcfffffff]
pci 0000:03:00.0: reg 10 32bit mmio: [0xfa000000-0xfaffffff]
pci 0000:03:00.0: reg 14 64bit mmio pref: [0xd0000000-0xdfffffff]
pci 0000:03:00.0: reg 1c 64bit mmio: [0xf8000000-0xf9ffffff]
pci 0000:03:00.0: reg 24 io port: [0xcc00-0xcc7f]
pci 0000:03:00.0: reg 30 32bit mmio pref: [0xf7fe0000-0xf7ffffff]
pci 0000:00:07.0: bridge io port: [0xc000-0xcfff]
pci 0000:00:07.0: bridge 32bit mmio: [0xf7f00000-0xfaffffff]
pci 0000:00:07.0: bridge 64bit mmio pref: [0xd0000000-0xdfffffff]
pci 0000:04:00.0: PME# supported from D0 D3hot D3cold
pci 0000:04:00.0: PME# disabled
pci 0000:04:00.2: PME# supported from D0 D3hot D3cold
pci 0000:04:00.2: PME# disabled
pci 0000:04:00.0: disabling ASPM on pre-1.1 PCIe device. You can enable
it with ''pcie_aspm=force''
pci 0000:00:1c.0: bridge 32bit mmio: [0xfbc00000-0xfbcfffff]
pci 0000:00:1c.0: bridge 64bit mmio pref: [0xf2f00000-0xf2ffffff]
pci 0000:05:0e.0: reg 10 32bit mmio pref: [0xf2ff0000-0xf2ffffff]
pci 0000:05:0e.0: reg 18 32bit mmio: [0xfbce0000-0xfbcfffff]
pci 0000:05:0e.0: reg 30 32bit mmio pref: [0xfbcd0000-0xfbcd7fff]
pci 0000:05:0e.0: supports D1
pci 0000:04:00.0: bridge 32bit mmio: [0xfbc00000-0xfbcfffff]
pci 0000:04:00.0: bridge 64bit mmio pref: [0xf2f00000-0xf2ffffff]
pci 0000:07:00.0: reg 10 32bit mmio: [0xfbde0000-0xfbdfffff]
pci 0000:07:00.0: reg 18 io port: [0xdc00-0xdc1f]
pci 0000:07:00.0: reg 1c 32bit mmio: [0xfbddc000-0xfbddffff]
pci 0000:07:00.0: PME# supported from D0 D3hot D3cold
pci 0000:07:00.0: PME# disabled
pci 0000:00:1c.4: bridge io port: [0xd000-0xdfff]
pci 0000:00:1c.4: bridge 32bit mmio: [0xfbd00000-0xfbdfffff]
pci 0000:08:00.0: reg 10 32bit mmio: [0xfbee0000-0xfbefffff]
pci 0000:08:00.0: reg 18 io port: [0xec00-0xec1f]
pci 0000:08:00.0: reg 1c 32bit mmio: [0xfbedc000-0xfbedffff]
pci 0000:08:00.0: PME# supported from D0 D3hot D3cold
pci 0000:08:00.0: PME# disabled
pci 0000:00:1c.5: bridge io port: [0xe000-0xefff]
pci 0000:00:1c.5: bridge 32bit mmio: [0xfbe00000-0xfbefffff]
pci 0000:00:1e.0: transparent bridge
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P0P1._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P0P4._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P0P8._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P0P9._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.NPE1._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.NPE3._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.NPE7._PRT]
(XEN) PCI add device 00:00.0
(XEN) PCI add device 00:01.0
(XEN) PCI add device 00:03.0
(XEN) PCI add device 00:07.0
(XEN) PCI add device 00:14.0
(XEN) PCI add device 00:14.1
(XEN) PCI add device 00:14.2
(XEN) PCI add device 00:14.3
(XEN) PCI add device 00:16.0
(XEN) PCI add device 00:16.1
(XEN) PCI add device 00:16.2
(XEN) PCI add device 00:16.3
(XEN) PCI add device 00:16.4
(XEN) PCI add device 00:16.5
(XEN) PCI add device 00:16.6
(XEN) PCI add device 00:16.7
(XEN) PCI add device 00:1a.0
(XEN) PCI add device 00:1a.1
(XEN) PCI add device 00:1a.2
(XEN) PCI add device 00:1a.7
(XEN) PCI add device 00:1b.0
(XEN) PCI add device 00:1c.0
(XEN) PCI add device 00:1c.4
(XEN) PCI add device 00:1c.5
(XEN) PCI add device 00:1d.0
(XEN) PCI add device 00:1d.1
(XEN) PCI add device 00:1d.2
(XEN) PCI add device 00:1d.7
(XEN) PCI add device 00:1e.0
(XEN) PCI add device 00:1f.0
(XEN) PCI add device 00:1f.2
(XEN) PCI add device 00:1f.3
(XEN) PCI add device 01:00.0
(XEN) PCI add device 03:00.0
(XEN) PCI add device 04:00.0
(XEN) PCI add device 04:00.2
(XEN) PCI add device 05:0e.0
(XEN) PCI add device 07:00.0
(XEN) PCI add device 08:00.0
initcall acpi_pci_root_init+0x0/0x28 returned 0 after 89843 usecs
calling acpi_pci_link_init+0x0/0x43 @ 1
ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 6 7 10 *11 12 14 15)
ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 6 7 *10 11 12 14 15)
ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 6 7 10 11 12 *14 15)
ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 6 7 10 11 12 14 *15)
ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 6 7 10 11 12 14 15) *0,
disabled.
ACPI: PCI Interrupt Link [LNKF] (IRQs 3 4 6 *7 10 11 12 14 15)
ACPI: PCI Interrupt Link [LNKG] (IRQs 3 4 *6 7 10 11 12 14 15)
ACPI: PCI Interrupt Link [LNKH] (IRQs 3 4 6 7 *10 11 12 14 15)
initcall acpi_pci_link_init+0x0/0x43 returned 0 after 4882 usecs
calling pnp_init+0x0/0x12 @ 1
initcall pnp_init+0x0/0x12 returned 0 after 0 usecs
calling __setup_shutdown_event+0x0/0x2a @ 1
initcall __setup_shutdown_event+0x0/0x2a returned 0 after 0 usecs
calling xen_pcpu_init+0x0/0xa7 @ 1
sync cpu 0 get result 1 max_id f
sync cpu 1 get result 1 max_id f
sync cpu 2 get result 1 max_id f
sync cpu 3 get result 1 max_id f
sync cpu 4 get result 1 max_id f
sync cpu 5 get result 1 max_id f
sync cpu 6 get result 1 max_id f
sync cpu 7 get result 1 max_id f
sync cpu 8 get result 1 max_id f
sync cpu 9 get result 1 max_id f
sync cpu a get result 1 max_id f
sync cpu b get result 1 max_id f
sync cpu c get result 1 max_id f
sync cpu d get result 1 max_id f
sync cpu e get result 1 max_id f
sync cpu f get result 1 max_id f
alloc irq_desc for 4270 on node 0
alloc kstat_irqs on node 0
initcall xen_pcpu_init+0x0/0xa7 returned 4270 after 16601 usecs
initcall xen_pcpu_init+0x0/0xa7 returned with error code 4270
calling xenbus_probe_backend_init+0x0/0x64 @ 1
initcall xenbus_probe_backend_init+0x0/0x64 returned 0 after 976 usecs
calling xenbus_probe_frontend_init+0x0/0x64 @ 1
initcall xenbus_probe_frontend_init+0x0/0x64 returned 0 after 0 usecs
calling balloon_init+0x0/0x208 @ 1
xen_balloon: Initialising balloon driver with page order 0.
initcall balloon_init+0x0/0x208 returned 0 after 0 usecs
calling xen_acpi_processor_extcntl_init+0x0/0x4f @ 1
initcall xen_acpi_processor_extcntl_init+0x0/0x4f returned 0 after 0
usecs
calling misc_init+0x0/0xb7 @ 1
initcall misc_init+0x0/0xb7 returned 0 after 0 usecs
calling vga_arb_device_init+0x0/0x78 @ 1
vgaarb: device added: PCI:0000:01:00.0,decodes=io
+mem,owns=none,locks=none
vgaarb: device added: PCI:0000:03:00.0,decodes=io+mem,owns=io
+mem,locks=none
vgaarb: loaded
initcall vga_arb_device_init+0x0/0x78 returned 0 after 976 usecs
calling cn_init+0x0/0xa3 @ 1
initcall cn_init+0x0/0xa3 returned 0 after 976 usecs
calling init_scsi+0x0/0x91 @ 1
SCSI subsystem initialized
initcall init_scsi+0x0/0x91 returned 0 after 976 usecs
calling ata_init+0x0/0x390 @ 1
libata version 3.00 loaded.
initcall ata_init+0x0/0x390 returned 0 after 1953 usecs
calling phy_init+0x0/0x31 @ 1
initcall phy_init+0x0/0x31 returned 0 after 976 usecs
calling init_pcmcia_cs+0x0/0x36 @ 1
initcall init_pcmcia_cs+0x0/0x36 returned 0 after 0 usecs
calling usb_init+0x0/0x1b2 @ 1
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
initcall usb_init+0x0/0x1b2 returned 0 after 1953 usecs
calling serio_init+0x0/0x89 @ 1
initcall serio_init+0x0/0x89 returned 0 after 976 usecs
calling input_init+0x0/0x13d @ 1
initcall input_init+0x0/0x13d returned 0 after 0 usecs
calling rtc_init+0x0/0x71 @ 1
initcall rtc_init+0x0/0x71 returned 0 after 976 usecs
calling power_supply_class_init+0x0/0x38 @ 1
initcall power_supply_class_init+0x0/0x38 returned 0 after 0 usecs
calling thermal_init+0x0/0x58 @ 1
initcall thermal_init+0x0/0x58 returned 0 after 0 usecs
calling md_init+0x0/0xd0 @ 1
initcall md_init+0x0/0xd0 returned 0 after 0 usecs
calling leds_init+0x0/0x40 @ 1
initcall leds_init+0x0/0x40 returned 0 after 0 usecs
calling pci_subsys_init+0x0/0x11a @ 1
PCI: Using ACPI for IRQ routing
initcall pci_subsys_init+0x0/0x11a returned 0 after 0 usecs
calling proto_init+0x0/0x12 @ 1
initcall proto_init+0x0/0x12 returned 0 after 0 usecs
calling net_dev_init+0x0/0x1a1 @ 1
initcall net_dev_init+0x0/0x1a1 returned 0 after 976 usecs
calling neigh_init+0x0/0x71 @ 1
initcall neigh_init+0x0/0x71 returned 0 after 0 usecs
calling fib_rules_init+0x0/0xa6 @ 1
initcall fib_rules_init+0x0/0xa6 returned 0 after 0 usecs
calling pktsched_init+0x0/0xd0 @ 1
initcall pktsched_init+0x0/0xd0 returned 0 after 0 usecs
calling tc_filter_init+0x0/0x4c @ 1
initcall tc_filter_init+0x0/0x4c returned 0 after 0 usecs
calling tc_action_init+0x0/0x4c @ 1
initcall tc_action_init+0x0/0x4c returned 0 after 0 usecs
calling genl_init+0x0/0x8f @ 1
initcall genl_init+0x0/0x8f returned 0 after 976 usecs
calling cipso_v4_init+0x0/0x88 @ 1
initcall cipso_v4_init+0x0/0x88 returned 0 after 0 usecs
calling wireless_nlevent_init+0x0/0x12 @ 1
initcall wireless_nlevent_init+0x0/0x12 returned 0 after 0 usecs
calling netlbl_init+0x0/0x81 @ 1
NetLabel: Initializing
NetLabel: domain hash size = 128
NetLabel: protocols = UNLABELED CIPSOv4
NetLabel: unlabeled traffic allowed by default
initcall netlbl_init+0x0/0x81 returned 0 after 0 usecs
calling sysctl_init+0x0/0x49 @ 1
initcall sysctl_init+0x0/0x49 returned 0 after 0 usecs
calling xen_mc_debugfs+0x0/0x118 @ 1
initcall xen_mc_debugfs+0x0/0x118 returned 0 after 976 usecs
calling xen_mmu_debugfs+0x0/0x2be @ 1
initcall xen_mmu_debugfs+0x0/0x2be returned 0 after 976 usecs
calling print_all_ICs+0x0/0x567 @ 1
initcall print_all_ICs+0x0/0x567 returned 0 after 976 usecs
calling hpet_late_init+0x0/0x1d1 @ 1
initcall hpet_late_init+0x0/0x1d1 returned -19 after 0 usecs
calling init_k8_nbs+0x0/0x28 @ 1
initcall init_k8_nbs+0x0/0x28 returned 0 after 0 usecs
calling clocksource_done_booting+0x0/0x5e @ 1
Switching to clocksource xen
kstop/0 used greatest stack depth: 6296 bytes left
initcall clocksource_done_booting+0x0/0x5e returned 0 after 8895 usecs
calling ftrace_init_debugfs+0x0/0x241 @ 1
initcall ftrace_init_debugfs+0x0/0x241 returned 0 after 653 usecs
calling rb_init_debugfs+0x0/0x2f @ 1
initcall rb_init_debugfs+0x0/0x2f returned 0 after 18 usecs
calling tracer_init_debugfs+0x0/0x347 @ 1
initcall tracer_init_debugfs+0x0/0x347 returned 0 after 2609 usecs
calling init_trace_printk_function_export+0x0/0x2f @ 1
initcall init_trace_printk_function_export+0x0/0x2f returned 0 after 18
usecs
calling stat_workqueue_init+0x0/0x2d @ 1
initcall stat_workqueue_init+0x0/0x2d returned 0 after 21 usecs
calling event_trace_init+0x0/0x1ed @ 1
initcall event_trace_init+0x0/0x1ed returned 0 after 87492 usecs
calling init_pipe_fs+0x0/0x4d @ 1
initcall init_pipe_fs+0x0/0x4d returned 0 after 212 usecs
calling eventpoll_init+0x0/0xda @ 1
initcall eventpoll_init+0x0/0xda returned 0 after 121 usecs
calling anon_inode_init+0x0/0x128 @ 1
initcall anon_inode_init+0x0/0x128 returned 0 after 142 usecs
calling blk_scsi_ioctl_init+0x0/0x297 @ 1
initcall blk_scsi_ioctl_init+0x0/0x297 returned 0 after 0 usecs
calling acpi_event_init+0x0/0x80 @ 1
initcall acpi_event_init+0x0/0x80 returned 0 after 155 usecs
calling pnpacpi_init+0x0/0x8c @ 1
pnp: PnP ACPI init
ACPI: bus type pnp registered
xen: registering gsi 8 triggering 1 polarity 0
xen_allocate_pirq: returning irq 8 for gsi 8
xen: --> irq=8
xen: registering gsi 13 triggering 1 polarity 0
xen_allocate_pirq: returning irq 13 for gsi 13
xen: --> irq=13
xen: registering gsi 4 triggering 1 polarity 0
xen_allocate_pirq: returning irq 4 for gsi 4
xen: --> irq=4
Already setup the GSI :4
xen: registering gsi 3 triggering 1 polarity 0
xen_allocate_pirq: returning irq 3 for gsi 3
xen: --> irq=3
pnp: PnP ACPI: found 14 devices
ACPI: ACPI bus type pnp unregistered
initcall pnpacpi_init+0x0/0x8c returned 0 after 72877 usecs
calling pnp_system_init+0x0/0x12 @ 1
system 00:01: iomem range 0xfed1c000-0xfed1ffff has been reserved
system 00:06: ioport range 0xa00-0xa0f has been reserved
system 00:06: ioport range 0x290-0x29f has been reserved
system 00:07: ioport range 0xca2-0xca3 has been reserved
system 00:07: ioport range 0xcf8-0xcff could not be reserved
system 00:07: ioport range 0x4d0-0x4d1 has been reserved
system 00:07: ioport range 0x800-0x87f has been reserved
system 00:07: ioport range 0x500-0x57f could not be reserved
system 00:07: iomem range 0xfed1c000-0xfed1ffff has been reserved
system 00:07: iomem range 0xfed20000-0xfed3ffff has been reserved
system 00:07: iomem range 0xfed40000-0xfed8ffff has been reserved
system 00:09: iomem range 0xfec00000-0xfec00fff could not be reserved
system 00:09: iomem range 0xfee00000-0xfee00fff has been reserved
system 00:0c: iomem range 0xe0000000-0xefffffff has been reserved
system 00:0d: iomem range 0xc0000-0xcffff could not be reserved
system 00:0d: iomem range 0xe0000-0xfffff could not be reserved
system 00:0d: iomem range 0xfed90000-0xffffffff could not be reserved
initcall pnp_system_init+0x0/0x12 returned 0 after 93585 usecs
calling pcistub_init+0x0/0x1e7 @ 1
initcall pcistub_init+0x0/0x1e7 returned 0 after 1622 usecs
calling chr_dev_init+0x0/0xc7 @ 1
initcall chr_dev_init+0x0/0xc7 returned 0 after 922 usecs
calling firmware_class_init+0x0/0x79 @ 1
initcall firmware_class_init+0x0/0x79 returned 0 after 96 usecs
calling init_pcmcia_bus+0x0/0x84 @ 1
initcall init_pcmcia_bus+0x0/0x84 returned 0 after 124 usecs
calling cpufreq_gov_performance_init+0x0/0x12 @ 1
initcall cpufreq_gov_performance_init+0x0/0x12 returned 0 after 16 usecs
calling cpufreq_gov_userspace_init+0x0/0x12 @ 1
initcall cpufreq_gov_userspace_init+0x0/0x12 returned 0 after 2 usecs
calling init_acpi_pm_clocksource+0x0/0xef @ 1
PM-Timer failed consistency check (0x0xffffff) - aborting.
initcall init_acpi_pm_clocksource+0x0/0xef returned -19 after 9691 usecs
calling pcibios_assign_resources+0x0/0x74 @ 1
pci 0000:00:01.0: PCI bridge, secondary bus 0000:01
pci 0000:00:01.0: IO window: 0xb000-0xbfff
pci 0000:00:01.0: MEM window: 0xf3f00000-0xf6ffffff
pci 0000:00:01.0: PREFETCH window: 0x000000c0000000-0x000000cfffffff
pci 0000:00:03.0: PCI bridge, secondary bus 0000:02
pci 0000:00:03.0: IO window: disabled
pci 0000:00:03.0: MEM window: disabled
pci 0000:00:03.0: PREFETCH window: disabled
pci 0000:00:07.0: PCI bridge, secondary bus 0000:03
pci 0000:00:07.0: IO window: 0xc000-0xcfff
pci 0000:00:07.0: MEM window: 0xf7f00000-0xfaffffff
pci 0000:00:07.0: PREFETCH window: 0x000000d0000000-0x000000dfffffff
pci 0000:04:00.0: PCI bridge, secondary bus 0000:05
pci 0000:04:00.0: IO window: disabled
pci 0000:04:00.0: MEM window: 0xfbc00000-0xfbcfffff
pci 0000:04:00.0: PREFETCH window: 0x000000f2f00000-0x000000f2ffffff
pci 0000:04:00.2: PCI bridge, secondary bus 0000:06
pci 0000:04:00.2: IO window: disabled
pci 0000:04:00.2: MEM window: disabled
pci 0000:04:00.2: PREFETCH window: disabled
pci 0000:00:1c.0: PCI bridge, secondary bus 0000:04
pci 0000:00:1c.0: IO window: 0x1000-0x1fff
pci 0000:00:1c.0: MEM window: 0xfbc00000-0xfbcfffff
pci 0000:00:1c.0: PREFETCH window: 0x000000f2f00000-0x000000f2ffffff
pci 0000:00:1c.4: PCI bridge, secondary bus 0000:07
pci 0000:00:1c.4: IO window: 0xd000-0xdfff
pci 0000:00:1c.4: MEM window: 0xfbd00000-0xfbdfffff
pci 0000:00:1c.4: PREFETCH window: 0x000000f0000000-0x000000f01fffff
pci 0000:00:1c.5: PCI bridge, secondary bus 0000:08
pci 0000:00:1c.5: IO window: 0xe000-0xefff
pci 0000:00:1c.5: MEM window: 0xfbe00000-0xfbefffff
pci 0000:00:1c.5: PREFETCH window: 0x000000f0200000-0x000000f03fffff
pci 0000:00:1e.0: PCI bridge, secondary bus 0000:09
pci 0000:00:1e.0: IO window: disabled
pci 0000:00:1e.0: MEM window: disabled
pci 0000:00:1e.0: PREFETCH window: disabled
pci 0000:00:01.0: setting latency timer to 64
pci 0000:00:03.0: setting latency timer to 64
pci 0000:00:07.0: setting latency timer to 64
pci 0000:00:1c.0: enabling device (0106 -> 0107)
xen: registering gsi 17 triggering 0 polarity 1
alloc irq_desc for 17 on node 0
alloc kstat_irqs on node 0
xen: --> irq=17
pci 0000:00:1c.0: PCI INT A -> GSI 17 (level, low) -> IRQ 17
pci 0000:00:1c.0: setting latency timer to 64
pci 0000:04:00.0: setting latency timer to 64
pci 0000:04:00.2: setting latency timer to 64
xen: registering gsi 17 triggering 0 polarity 1
xen_allocate_pirq: returning irq 17 for gsi 17
xen: --> irq=17
Already setup the GSI :17
pci 0000:00:1c.4: PCI INT A -> GSI 17 (level, low) -> IRQ 17
pci 0000:00:1c.4: setting latency timer to 64
xen: registering gsi 16 triggering 0 polarity 1
alloc irq_desc for 16 on node 0
alloc kstat_irqs on node 0
xen: --> irq=16
pci 0000:00:1c.5: PCI INT B -> GSI 16 (level, low) -> IRQ 16
pci 0000:00:1c.5: setting latency timer to 64
pci 0000:00:1e.0: setting latency timer to 64
pci_bus 0000:00: resource 0 io: [0x00-0xffff]
pci_bus 0000:00: resource 1 mem: [0x000000-0xffffffffffffffff]
pci_bus 0000:01: resource 0 io: [0xb000-0xbfff]
pci_bus 0000:01: resource 1 mem: [0xf3f00000-0xf6ffffff]
pci_bus 0000:01: resource 2 pref mem [0xc0000000-0xcfffffff]
pci_bus 0000:03: resource 0 io: [0xc000-0xcfff]
pci_bus 0000:03: resource 1 mem: [0xf7f00000-0xfaffffff]
pci_bus 0000:03: resource 2 pref mem [0xd0000000-0xdfffffff]
pci_bus 0000:04: resource 0 io: [0x1000-0x1fff]
pci_bus 0000:04: resource 1 mem: [0xfbc00000-0xfbcfffff]
pci_bus 0000:04: resource 2 pref mem [0xf2f00000-0xf2ffffff]
pci_bus 0000:05: resource 1 mem: [0xfbc00000-0xfbcfffff]
pci_bus 0000:05: resource 2 pref mem [0xf2f00000-0xf2ffffff]
pci_bus 0000:07: resource 0 io: [0xd000-0xdfff]
pci_bus 0000:07: resource 1 mem: [0xfbd00000-0xfbdfffff]
pci_bus 0000:07: resource 2 pref mem [0xf0000000-0xf01fffff]
pci_bus 0000:08: resource 0 io: [0xe000-0xefff]
pci_bus 0000:08: resource 1 mem: [0xfbe00000-0xfbefffff]
pci_bus 0000:08: resource 2 pref mem [0xf0200000-0xf03fffff]
pci_bus 0000:09: resource 3 io: [0x00-0xffff]
pci_bus 0000:09: resource 4 mem: [0x000000-0xffffffffffffffff]
initcall pcibios_assign_resources+0x0/0x74 returned 0 after 361318 usecs
calling sysctl_core_init+0x0/0x38 @ 1
initcall sysctl_core_init+0x0/0x38 returned 0 after 105 usecs
calling inet_init+0x0/0x209 @ 1
NET: Registered protocol family 2
IP route cache hash table entries: 524288 (order: 10, 4194304 bytes)
TCP established hash table entries: 524288 (order: 11, 8388608 bytes)
TCP bind hash table entries: 65536 (order: 10, 4718592 bytes)
TCP: Hash tables configured (established 524288 bind 65536)
TCP reno registered
initcall inet_init+0x0/0x209 returned 0 after 40865 usecs
calling af_unix_init+0x0/0x55 @ 1
NET: Registered protocol family 1
initcall af_unix_init+0x0/0x55 returned 0 after 3095 usecs
calling pci_apply_final_quirks+0x0/0x36 @ 1
pci 0000:03:00.0: Boot video device
pci 0000:04:00.0: rerouting interrupts for [8086:0370]
pci 0000:04:00.2: rerouting interrupts for [8086:0372]
initcall pci_apply_final_quirks+0x0/0x36 returned 0 after 13680 usecs
calling populate_rootfs+0x0/0x263 @ 1
Trying to unpack rootfs image as initramfs...
Freeing initrd memory: 214149k freed
initcall populate_rootfs+0x0/0x263 returned 0 after 592711 usecs
calling pci_iommu_init+0x0/0x50 @ 1
DMA-API: preallocated 32768 debug entries
DMA-API: debugging enabled by kernel config
PCI-DMA: Using software bounce buffering for IO (SWIOTLB)
DMA: Placing 64MB software IO TLB between ffff880020000000 -
ffff880024000000
DMA: software IO TLB at phys 0x20000000 - 0x24000000
initcall pci_iommu_init+0x0/0x50 returned 0 after 61360 usecs
calling calgary_fixup_tce_spaces+0x0/0xf9 @ 1
initcall calgary_fixup_tce_spaces+0x0/0xf9 returned -19 after 0 usecs
calling i8259A_init_sysfs+0x0/0x22 @ 1
initcall i8259A_init_sysfs+0x0/0x22 returned 0 after 109 usecs
calling vsyscall_init+0x0/0x6c @ 1
initcall vsyscall_init+0x0/0x6c returned 0 after 117 usecs
calling sbf_init+0x0/0xef @ 1
initcall sbf_init+0x0/0xef returned 0 after 0 usecs
calling i8237A_init_sysfs+0x0/0x22 @ 1
initcall i8237A_init_sysfs+0x0/0x22 returned 0 after 80 usecs
calling add_rtc_cmos+0x0/0xc4 @ 1
initcall add_rtc_cmos+0x0/0xc4 returned 0 after 3 usecs
calling cache_sysfs_init+0x0/0x67 @ 1
initcall cache_sysfs_init+0x0/0x67 returned 0 after 6102 usecs
calling mce_init_device+0x0/0x109 @ 1
initcall mce_init_device+0x0/0x109 returned 0 after 2029 usecs
calling threshold_init_device+0x0/0x98 @ 1
initcall threshold_init_device+0x0/0x98 returned 0 after 1 usecs
calling thermal_throttle_init_device+0x0/0x93 @ 1
initcall thermal_throttle_init_device+0x0/0x93 returned 0 after 0 usecs
calling msr_init+0x0/0x14c @ 1
initcall msr_init+0x0/0x14c returned 0 after 1693 usecs
calling cpuid_init+0x0/0x14c @ 1
initcall cpuid_init+0x0/0x14c returned 0 after 1636 usecs
calling ioapic_init_sysfs+0x0/0xa7 @ 1
initcall ioapic_init_sysfs+0x0/0xa7 returned 0 after 114 usecs
calling add_pcspkr+0x0/0x28 @ 1
initcall add_pcspkr+0x0/0x28 returned 0 after 77 usecs
calling audit_classes_init+0x0/0xaf @ 1
initcall audit_classes_init+0x0/0xaf returned 0 after 13 usecs
calling pt_dump_init+0x0/0x30 @ 1
initcall pt_dump_init+0x0/0x30 returned 0 after 66 usecs
calling init_vdso_vars+0x0/0x220 @ 1
initcall init_vdso_vars+0x0/0x220 returned 0 after 46 usecs
calling ia32_binfmt_init+0x0/0x14 @ 1
initcall ia32_binfmt_init+0x0/0x14 returned 0 after 32 usecs
calling sysenter_setup+0x0/0x2df @ 1
initcall sysenter_setup+0x0/0x2df returned 0 after 3 usecs
calling init_sched_debug_procfs+0x0/0x2c @ 1
initcall init_sched_debug_procfs+0x0/0x2c returned 0 after 15 usecs
calling proc_schedstat_init+0x0/0x22 @ 1
initcall proc_schedstat_init+0x0/0x22 returned 0 after 10 usecs
calling proc_execdomains_init+0x0/0x22 @ 1
initcall proc_execdomains_init+0x0/0x22 returned 0 after 10 usecs
calling ioresources_init+0x0/0x3c @ 1
initcall ioresources_init+0x0/0x3c returned 0 after 50 usecs
calling uid_cache_init+0x0/0x8d @ 1
initcall uid_cache_init+0x0/0x8d returned 0 after 71 usecs
calling init_posix_timers+0x0/0x19f @ 1
initcall init_posix_timers+0x0/0x19f returned 0 after 66 usecs
calling init_posix_cpu_timers+0x0/0xe5 @ 1
initcall init_posix_cpu_timers+0x0/0xe5 returned 0 after 0 usecs
calling nsproxy_cache_init+0x0/0x2d @ 1
initcall nsproxy_cache_init+0x0/0x2d returned 0 after 88 usecs
calling create_proc_profile+0x0/0x282 @ 1
initcall create_proc_profile+0x0/0x282 returned 0 after 0 usecs
calling timekeeping_init_device+0x0/0x22 @ 1
initcall timekeeping_init_device+0x0/0x22 returned 0 after 81 usecs
calling init_clocksource_sysfs+0x0/0x50 @ 1
initcall init_clocksource_sysfs+0x0/0x50 returned 0 after 113 usecs
calling init_timer_list_procfs+0x0/0x2c @ 1
initcall init_timer_list_procfs+0x0/0x2c returned 0 after 11 usecs
calling init_tstats_procfs+0x0/0x2c @ 1
initcall init_tstats_procfs+0x0/0x2c returned 0 after 10 usecs
calling lockdep_proc_init+0x0/0x7c @ 1
initcall lockdep_proc_init+0x0/0x7c returned 0 after 38 usecs
calling futex_init+0x0/0xbe @ 1
initcall futex_init+0x0/0xbe returned 0 after 71 usecs
calling proc_dma_init+0x0/0x22 @ 1
initcall proc_dma_init+0x0/0x22 returned 0 after 11 usecs
calling proc_modules_init+0x0/0x22 @ 1
initcall proc_modules_init+0x0/0x22 returned 0 after 10 usecs
calling kallsyms_init+0x0/0x25 @ 1
initcall kallsyms_init+0x0/0x25 returned 0 after 10 usecs
calling snapshot_device_init+0x0/0x12 @ 1
initcall snapshot_device_init+0x0/0x12 returned 0 after 83 usecs
calling crash_save_vmcoreinfo_init+0x0/0x46d @ 1
initcall crash_save_vmcoreinfo_init+0x0/0x46d returned 0 after 22 usecs
calling crash_notes_memory_init+0x0/0x38 @ 1
initcall crash_notes_memory_init+0x0/0x38 returned 0 after 11 usecs
calling pid_namespaces_init+0x0/0x2d @ 1
initcall pid_namespaces_init+0x0/0x2d returned 0 after 100 usecs
calling ikconfig_init+0x0/0x39 @ 1
initcall ikconfig_init+0x0/0x39 returned 0 after 11 usecs
calling audit_init+0x0/0x153 @ 1
audit: initializing netlink socket (disabled)
type=2000 audit(1275218265.439:1): initialized
initcall audit_init+0x0/0x153 returned 0 after 8236 usecs
calling audit_tree_init+0x0/0x49 @ 1
initcall audit_tree_init+0x0/0x49 returned 0 after 2 usecs
calling init_kprobes+0x0/0x19e @ 1
initcall init_kprobes+0x0/0x19e returned 0 after 12070 usecs
calling hung_task_init+0x0/0x53 @ 1
initcall hung_task_init+0x0/0x53 returned 0 after 203 usecs
calling utsname_sysctl_init+0x0/0x14 @ 1
initcall utsname_sysctl_init+0x0/0x14 returned 0 after 83 usecs
calling init_tracepoints+0x0/0x17 @ 1
initcall init_tracepoints+0x0/0x17 returned 0 after 0 usecs
calling init_lstats_procfs+0x0/0x25 @ 1
initcall init_lstats_procfs+0x0/0x25 returned 0 after 12 usecs
calling ftrace_mod_cmd_init+0x0/0x12 @ 1
initcall ftrace_mod_cmd_init+0x0/0x12 returned 0 after 18 usecs
calling init_events+0x0/0x63 @ 1
initcall init_events+0x0/0x63 returned 0 after 11 usecs
calling init_sched_switch_trace+0x0/0x12 @ 1
initcall init_sched_switch_trace+0x0/0x12 returned 0 after 3 usecs
calling init_stack_trace+0x0/0x12 @ 1
initcall init_stack_trace+0x0/0x12 returned 0 after 1 usecs
calling init_function_trace+0x0/0x3e @ 1
initcall init_function_trace+0x0/0x3e returned 0 after 3 usecs
calling init_wakeup_tracer+0x0/0x22 @ 1
initcall init_wakeup_tracer+0x0/0x22 returned 0 after 3 usecs
calling stack_trace_init+0x0/0x6b @ 1
initcall stack_trace_init+0x0/0x6b returned 0 after 38 usecs
calling init_mmio_trace+0x0/0x12 @ 1
initcall init_mmio_trace+0x0/0x12 returned 0 after 1 usecs
calling init_graph_trace+0x0/0x32 @ 1
initcall init_graph_trace+0x0/0x32 returned 0 after 2 usecs
calling init_kmem_tracer+0x0/0x56 @ 1
initcall init_kmem_tracer+0x0/0x56 returned 0 after 4 usecs
calling init_blk_tracer+0x0/0x57 @ 1
initcall init_blk_tracer+0x0/0x57 returned 0 after 3 usecs
calling perf_event_sysfs_init+0x0/0x19 @ 1
initcall perf_event_sysfs_init+0x0/0x19 returned 0 after 14 usecs
calling init_per_zone_wmark_min+0x0/0x68 @ 1
initcall init_per_zone_wmark_min+0x0/0x68 returned 0 after 899 usecs
calling kswapd_init+0x0/0x78 @ 1
initcall kswapd_init+0x0/0x78 returned 0 after 336 usecs
calling setup_vmstat+0x0/0xc3 @ 1
initcall setup_vmstat+0x0/0xc3 returned 0 after 180 usecs
calling mm_sysfs_init+0x0/0x29 @ 1
initcall mm_sysfs_init+0x0/0x29 returned 0 after 9 usecs
calling proc_vmalloc_init+0x0/0x25 @ 1
initcall proc_vmalloc_init+0x0/0x25 returned 0 after 10 usecs
calling procswaps_init+0x0/0x22 @ 1
initcall procswaps_init+0x0/0x22 returned 0 after 10 usecs
calling hugetlb_init+0x0/0x3c8 @ 1
HugeTLB registered 2 MB page size, pre-allocated 0 pages
initcall hugetlb_init+0x0/0x3c8 returned 0 after 5058 usecs
calling slab_proc_init+0x0/0x25 @ 1
initcall slab_proc_init+0x0/0x25 returned 0 after 11 usecs
calling slab_sysfs_init+0x0/0xf0 @ 1
initcall slab_sysfs_init+0x0/0xf0 returned 0 after 17492 usecs
calling fasync_init+0x0/0x2a @ 1
initcall fasync_init+0x0/0x2a returned 0 after 247 usecs
calling proc_filesystems_init+0x0/0x22 @ 1
initcall proc_filesystems_init+0x0/0x22 returned 0 after 12 usecs
calling dnotify_init+0x0/0x80 @ 1
initcall dnotify_init+0x0/0x80 returned 0 after 546 usecs
calling inotify_setup+0x0/0x12 @ 1
initcall inotify_setup+0x0/0x12 returned 0 after 0 usecs
calling inotify_user_setup+0x0/0xbe @ 1
initcall inotify_user_setup+0x0/0xbe returned 0 after 651 usecs
calling aio_setup+0x0/0xa5 @ 1
initcall aio_setup+0x0/0xa5 returned 0 after 3119 usecs
calling proc_locks_init+0x0/0x22 @ 1
initcall proc_locks_init+0x0/0x22 returned 0 after 13 usecs
calling init_sys32_ioctl+0x0/0x85 @ 1
initcall init_sys32_ioctl+0x0/0x85 returned 0 after 12 usecs
calling init_mbcache+0x0/0x14 @ 1
initcall init_mbcache+0x0/0x14 returned 0 after 1 usecs
calling dquot_init+0x0/0x105 @ 1
VFS: Disk quotas dquot_6.5.2
Dquot-cache hash table entries: 512 (order 0, 4096 bytes)
initcall dquot_init+0x0/0x105 returned 0 after 8080 usecs
calling init_v2_quota_format+0x0/0x12 @ 1
initcall init_v2_quota_format+0x0/0x12 returned 0 after 16 usecs
calling proc_cmdline_init+0x0/0x22 @ 1
initcall proc_cmdline_init+0x0/0x22 returned 0 after 12 usecs
calling proc_cpuinfo_init+0x0/0x22 @ 1
initcall proc_cpuinfo_init+0x0/0x22 returned 0 after 10 usecs
calling proc_devices_init+0x0/0x22 @ 1
initcall proc_devices_init+0x0/0x22 returned 0 after 43 usecs
calling proc_interrupts_init+0x0/0x22 @ 1
initcall proc_interrupts_init+0x0/0x22 returned 0 after 10 usecs
calling proc_loadavg_init+0x0/0x22 @ 1
initcall proc_loadavg_init+0x0/0x22 returned 0 after 10 usecs
calling proc_meminfo_init+0x0/0x22 @ 1
initcall proc_meminfo_init+0x0/0x22 returned 0 after 10 usecs
calling proc_stat_init+0x0/0x22 @ 1
initcall proc_stat_init+0x0/0x22 returned 0 after 10 usecs
calling proc_uptime_init+0x0/0x22 @ 1
initcall proc_uptime_init+0x0/0x22 returned 0 after 10 usecs
calling proc_version_init+0x0/0x22 @ 1
initcall proc_version_init+0x0/0x22 returned 0 after 10 usecs
calling proc_softirqs_init+0x0/0x22 @ 1
initcall proc_softirqs_init+0x0/0x22 returned 0 after 10 usecs
calling proc_kcore_init+0x0/0xa9 @ 1
initcall proc_kcore_init+0x0/0xa9 returned 0 after 31 usecs
calling vmcore_init+0x0/0x8d2 @ 1
initcall vmcore_init+0x0/0x8d2 returned 0 after 0 usecs
calling proc_kmsg_init+0x0/0x25 @ 1
initcall proc_kmsg_init+0x0/0x25 returned 0 after 10 usecs
calling proc_page_init+0x0/0x42 @ 1
initcall proc_page_init+0x0/0x42 returned 0 after 19 usecs
calling init_devpts_fs+0x0/0x4c @ 1
initcall init_devpts_fs+0x0/0x4c returned 0 after 239 usecs
calling init_ext3_fs+0x0/0x71 @ 1
initcall init_ext3_fs+0x0/0x71 returned 0 after 568 usecs
calling init_ext4_fs+0x0/0xea @ 1
initcall init_ext4_fs+0x0/0xea returned 0 after 1547 usecs
calling journal_init+0x0/0x93 @ 1
initcall journal_init+0x0/0x93 returned 0 after 975 usecs
calling journal_init+0x0/0xec @ 1
initcall journal_init+0x0/0xec returned 0 after 1124 usecs
calling init_ramfs_fs+0x0/0x12 @ 1
initcall init_ramfs_fs+0x0/0x12 returned 0 after 3 usecs
calling init_hugetlbfs_fs+0x0/0x98 @ 1
initcall init_hugetlbfs_fs+0x0/0x98 returned 0 after 444 usecs
calling init_iso9660_fs+0x0/0x71 @ 1
initcall init_iso9660_fs+0x0/0x71 returned 0 after 306 usecs
calling init_nls_cp437+0x0/0x12 @ 1
initcall init_nls_cp437+0x0/0x12 returned 0 after 16 usecs
calling init_nls_ascii+0x0/0x12 @ 1
initcall init_nls_ascii+0x0/0x12 returned 0 after 1 usecs
calling ipc_init+0x0/0x23 @ 1
msgmni has been set to 21017
initcall ipc_init+0x0/0x23 returned 0 after 2645 usecs
calling ipc_sysctl_init+0x0/0x14 @ 1
initcall ipc_sysctl_init+0x0/0x14 returned 0 after 140 usecs
calling init_mqueue_fs+0x0/0xc9 @ 1
initcall init_mqueue_fs+0x0/0xc9 returned 0 after 600 usecs
calling key_proc_init+0x0/0x59 @ 1
initcall key_proc_init+0x0/0x59 returned 0 after 23 usecs
calling selinux_nf_ip_init+0x0/0x60 @ 1
SELinux: Registering netfilter hooks
initcall selinux_nf_ip_init+0x0/0x60 returned 0 after 3407 usecs
calling init_sel_fs+0x0/0x68 @ 1
initcall init_sel_fs+0x0/0x68 returned 0 after 996 usecs
calling selnl_init+0x0/0x4d @ 1
initcall selnl_init+0x0/0x4d returned 0 after 54 usecs
calling sel_netif_init+0x0/0x66 @ 1
initcall sel_netif_init+0x0/0x66 returned 0 after 6 usecs
calling sel_netnode_init+0x0/0x73 @ 1
initcall sel_netnode_init+0x0/0x73 returned 0 after 2 usecs
calling sel_netport_init+0x0/0x73 @ 1
initcall sel_netport_init+0x0/0x73 returned 0 after 9 usecs
calling aurule_init+0x0/0x37 @ 1
initcall aurule_init+0x0/0x37 returned 0 after 0 usecs
calling crypto_wq_init+0x0/0x32 @ 1
initcall crypto_wq_init+0x0/0x32 returned 0 after 2705 usecs
calling crypto_algapi_init+0x0/0xd @ 1
initcall crypto_algapi_init+0x0/0xd returned 0 after 49 usecs
calling skcipher_module_init+0x0/0x35 @ 1
initcall skcipher_module_init+0x0/0x35 returned 0 after 0 usecs
calling chainiv_module_init+0x0/0x12 @ 1
initcall chainiv_module_init+0x0/0x12 returned 0 after 37 usecs
calling eseqiv_module_init+0x0/0x12 @ 1
initcall eseqiv_module_init+0x0/0x12 returned 0 after 2 usecs
calling hmac_module_init+0x0/0x12 @ 1
initcall hmac_module_init+0x0/0x12 returned 0 after 1 usecs
calling md5_mod_init+0x0/0x12 @ 1
cryptomgr_test used greatest stack depth: 5672 bytes left
initcall md5_mod_init+0x0/0x12 returned 0 after 415 usecs
calling sha1_generic_mod_init+0x0/0x12 @ 1
initcall sha1_generic_mod_init+0x0/0x12 returned 0 after 271 usecs
calling crc32c_mod_init+0x0/0x12 @ 1
initcall crc32c_mod_init+0x0/0x12 returned 0 after 330 usecs
calling krng_mod_init+0x0/0x12 @ 1
alg: No test for stdrng (krng)
initcall krng_mod_init+0x0/0x12 returned 0 after 212 usecs
calling proc_genhd_init+0x0/0x3c @ 1
initcall proc_genhd_init+0x0/0x3c returned 0 after 24 usecs
calling bsg_init+0x0/0x132 @ 1
Block layer SCSI generic (bsg) driver version 0.4 loaded (major 252)
initcall bsg_init+0x0/0x132 returned 0 after 308 usecs
calling noop_init+0x0/0x14 @ 1
io scheduler noop registered
initcall noop_init+0x0/0x14 returned 0 after 19 usecs
calling as_init+0x0/0x14 @ 1
io scheduler anticipatory registered
initcall as_init+0x0/0x14 returned 0 after 2 usecs
calling deadline_init+0x0/0x14 @ 1
io scheduler deadline registered
initcall deadline_init+0x0/0x14 returned 0 after 2 usecs
calling cfq_init+0x0/0x94 @ 1
io scheduler cfq registered (default)
initcall cfq_init+0x0/0x94 returned 0 after 495 usecs
calling debug_objects_init_debugfs+0x0/0x64 @ 1
initcall debug_objects_init_debugfs+0x0/0x64 returned 0 after 80 usecs
calling percpu_counter_startup+0x0/0x38 @ 1
initcall percpu_counter_startup+0x0/0x38 returned 0 after 2 usecs
calling dynamic_debug_init+0x0/0x127 @ 1
initcall dynamic_debug_init+0x0/0x127 returned 0 after 328 usecs
calling pci_proc_init+0x0/0x6b @ 1
initcall pci_proc_init+0x0/0x6b returned 0 after 820 usecs
calling pcie_portdrv_init+0x0/0x4c @ 1
alloc irq_desc for 4269 on node 0
alloc kstat_irqs on node 0
pcieport 0000:00:01.0: setting latency timer to 64
alloc irq_desc for 4268 on node 0
alloc kstat_irqs on node 0
pcieport 0000:00:03.0: setting latency timer to 64
alloc irq_desc for 4267 on node 0
alloc kstat_irqs on node 0
pcieport 0000:00:07.0: setting latency timer to 64
alloc irq_desc for 4266 on node 0
alloc kstat_irqs on node 0
pcieport 0000:00:1c.0: setting latency timer to 64
alloc irq_desc for 4265 on node 0
alloc kstat_irqs on node 0
pcieport 0000:00:1c.4: setting latency timer to 64
alloc irq_desc for 4264 on node 0
alloc kstat_irqs on node 0
pcieport 0000:00:1c.5: setting latency timer to 64
initcall pcie_portdrv_init+0x0/0x4c returned 0 after 4286 usecs
calling aer_service_init+0x0/0x2b @ 1
aer 0000:00:01.0:pcie02: AER service couldn''t init device: no _OSC
support
aer 0000:00:03.0:pcie02: AER service couldn''t init device: no _OSC
support
aer 0000:00:07.0:pcie02: AER service couldn''t init device: no _OSC
support
initcall aer_service_init+0x0/0x2b returned 0 after 202 usecs
calling pci_hotplug_init+0x0/0x1d @ 1
pci_hotplug: PCI Hot Plug PCI Core version: 0.5
initcall pci_hotplug_init+0x0/0x1d returned 0 after 1 usecs
calling pcied_init+0x0/0x79 @ 1
pciehp: PCI Express Hot Plug Controller Driver version: 0.4
initcall pcied_init+0x0/0x79 returned 0 after 646 usecs
calling acpiphp_init+0x0/0x5f @ 1
acpiphp: ACPI Hot Plug PCI Controller Driver version: 0.5
initcall acpiphp_init+0x0/0x5f returned -19 after 2301 usecs
calling pci_stub_init+0x0/0x139 @ 1
pci-stub: invalid id string ""
initcall pci_stub_init+0x0/0x139 returned 0 after 146 usecs
calling fb_console_init+0x0/0x11d @ 1
cryptomgr_test used greatest stack depth: 5400 bytes left
initcall fb_console_init+0x0/0x11d returned 0 after 291391 usecs
calling xenfb_init+0x0/0x5d @ 1
initcall xenfb_init+0x0/0x5d returned -19 after 0 usecs
calling vesafb_init+0x0/0x23a @ 1
initcall vesafb_init+0x0/0x23a returned 0 after 195 usecs
calling efifb_init+0x0/0x1ed @ 1
initcall efifb_init+0x0/0x1ed returned -19 after 4 usecs
calling acpi_reserve_resources+0x0/0xeb @ 1
initcall acpi_reserve_resources+0x0/0xeb returned 0 after 9 usecs
calling irqrouter_init_sysfs+0x0/0x38 @ 1
initcall irqrouter_init_sysfs+0x0/0x38 returned 0 after 78 usecs
calling acpi_ac_init+0x0/0x45 @ 1
initcall acpi_ac_init+0x0/0x45 returned 0 after 182 usecs
calling acpi_button_init+0x0/0x56 @ 1
input: Power Button
as /devices/LNXSYSTM:00/LNXSYBUS:00/PNP0C0C:00/input/input0
ACPI: Power Button [PWRB]
input: Power Button as /devices/LNXSYSTM:00/LNXPWRBN:00/input/input1
ACPI: Power Button [PWRF]
initcall acpi_button_init+0x0/0x56 returned 0 after 18361 usecs
calling acpi_fan_init+0x0/0x56 @ 1
initcall acpi_fan_init+0x0/0x56 returned 0 after 124 usecs
calling acpi_pci_slot_init+0x0/0x20 @ 1
initcall acpi_pci_slot_init+0x0/0x20 returned 0 after 1902 usecs
calling acpi_processor_init+0x0/0x132 @ 1
ACPI: SSDT 00000000bf77e1e0 02B94 (v01 DpgPmm P001Ist 00000011 INTL
20051117)
ACPI: SSDT 00000000bf780d80 00980 (v01 PmRef P001Cst 00003001 INTL
20051117)
ACPI: SSDT 00000000bf781700 006E2 (v01 PmRef Cpu0Tst 00003000 INTL
20051117)
(XEN) cpuid.MWAIT[.eax=40, .ebx=40, .ecx=3, .edx=1120]
(XEN) Monitor-Mwait will be used to enter C-1 state
(XEN) cpuid.MWAIT[.eax=40, .ebx=40, .ecx=3, .edx=1120]
(XEN) Monitor-Mwait will be used to enter C-3 state
(XEN) cpuid.MWAIT[.eax=40, .ebx=40, .ecx=3, .edx=1120]
(XEN) Monitor-Mwait will be used to enter C-3 state
ACPI: CPU-1 (power states: C1[C1] C2[C3] C3[C3])
(XEN) cpuid.MWAIT[.eax=40, .ebx=40, .ecx=3, .edx=1120]
(XEN) Monitor-Mwait will be used to enter C-1 state
(XEN) cpuid.MWAIT[.eax=40, .ebx=40, .ecx=3, .edx=1120]
(XEN) Monitor-Mwait will be used to enter C-3 state
(XEN) cpuid.MWAIT[.eax=40, .ebx=40, .ecx=3, .edx=1120]
(XEN) Monitor-Mwait will be used to enter C-3 state
ACPI: CPU-1 (power states: C1[C1] C2[C3] C3[C3])
(XEN) cpuid.MWAIT[.eax=40, .ebx=40, .ecx=3, .edx=1120]
(XEN) Monitor-Mwait will be used to enter C-1 state
(XEN) cpuid.MWAIT[.eax=40, .ebx=40, .ecx=3, .edx=1120]
(XEN) Monitor-Mwait will be used to enter C-3 state
(XEN) cpuid.MWAIT[.eax=40, .ebx=40, .ecx=3, .edx=1120]
(XEN) Monitor-Mwait will be used to enter C-3 state
ACPI: CPU-1 (power states: C1[C1] C2[C3] C3[C3])
(XEN) cpuid.MWAIT[.eax=40, .ebx=40, .ecx=3, .edx=1120]
(XEN) Monitor-Mwait will be used to enter C-1 state
(XEN) cpuid.MWAIT[.eax=40, .ebx=40, .ecx=3, .edx=1120]
(XEN) Monitor-Mwait will be used to enter C-3 state
(XEN) cpuid.MWAIT[.eax=40, .ebx=40, .ecx=3, .edx=1120]
(XEN) Monitor-Mwait will be used to enter C-3 state
ACPI: CPU-1 (power states: C1[C1] C2[C3] C3[C3])
(XEN) cpuid.MWAIT[.eax=40, .ebx=40, .ecx=3, .edx=1120]
(XEN) Monitor-Mwait will be used to enter C-1 state
(XEN) cpuid.MWAIT[.eax=40, .ebx=40, .ecx=3, .edx=1120]
(XEN) Monitor-Mwait will be used to enter C-3 state
(XEN) cpuid.MWAIT[.eax=40, .ebx=40, .ecx=3, .edx=1120]
(XEN) Monitor-Mwait will be used to enter C-3 state
ACPI: CPU-1 (power states: C1[C1] C2[C3] C3[C3])
(XEN) cpuid.MWAIT[.eax=40, .ebx=40, .ecx=3, .edx=1120]
(XEN) Monitor-Mwait will be used to enter C-1 state
(XEN) cpuid.MWAIT[.eax=40, .ebx=40, .ecx=3, .edx=1120]
(XEN) Monitor-Mwait will be used to enter C-3 state
(XEN) cpuid.MWAIT[.eax=40, .ebx=40, .ecx=3, .edx=1120]
(XEN) Monitor-Mwait will be used to enter C-3 state
ACPI: CPU-1 (power states: C1[C1] C2[C3] C3[C3])
(XEN) cpuid.MWAIT[.eax=40, .ebx=40, .ecx=3, .edx=1120]
(XEN) Monitor-Mwait will be used to enter C-1 state
(XEN) cpuid.MWAIT[.eax=40, .ebx=40, .ecx=3, .edx=1120]
(XEN) Monitor-Mwait will be used to enter C-3 state
(XEN) cpuid.MWAIT[.eax=40, .ebx=40, .ecx=3, .edx=1120]
(XEN) Monitor-Mwait will be used to enter C-3 state
ACPI: CPU-1 (power states: C1[C1] C2[C3] C3[C3])
(XEN) cpuid.MWAIT[.eax=40, .ebx=40, .ecx=3, .edx=1120]
(XEN) Monitor-Mwait will be used to enter C-1 state
(XEN) cpuid.MWAIT[.eax=40, .ebx=40, .ecx=3, .edx=1120]
(XEN) Monitor-Mwait will be used to enter C-3 state
(XEN) cpuid.MWAIT[.eax=40, .ebx=40, .ecx=3, .edx=1120]
(XEN) Monitor-Mwait will be used to enter C-3 state
ACPI: CPU-1 (power states: C1[C1] C2[C3] C3[C3])
(XEN) cpuid.MWAIT[.eax=40, .ebx=40, .ecx=3, .edx=1120]
(XEN) Monitor-Mwait will be used to enter C-1 state
(XEN) cpuid.MWAIT[.eax=40, .ebx=40, .ecx=3, .edx=1120]
(XEN) Monitor-Mwait will be used to enter C-3 state
(XEN) cpuid.MWAIT[.eax=40, .ebx=40, .ecx=3, .edx=1120]
(XEN) Monitor-Mwait will be used to enter C-3 state
ACPI: CPU-1 (power states: C1[C1] C2[C3] C3[C3])
(XEN) cpuid.MWAIT[.eax=40, .ebx=40, .ecx=3, .edx=1120]
(XEN) Monitor-Mwait will be used to enter C-1 state
(XEN) cpuid.MWAIT[.eax=40, .ebx=40, .ecx=3, .edx=1120]
(XEN) Monitor-Mwait will be used to enter C-3 state
(XEN) cpuid.MWAIT[.eax=40, .ebx=40, .ecx=3, .edx=1120]
(XEN) Monitor-Mwait will be used to enter C-3 state
ACPI: CPU-1 (power states: C1[C1] C2[C3] C3[C3])
(XEN) cpuid.MWAIT[.eax=40, .ebx=40, .ecx=3, .edx=1120]
(XEN) Monitor-Mwait will be used to enter C-1 state
(XEN) cpuid.MWAIT[.eax=40, .ebx=40, .ecx=3, .edx=1120]
(XEN) Monitor-Mwait will be used to enter C-3 state
(XEN) cpuid.MWAIT[.eax=40, .ebx=40, .ecx=3, .edx=1120]
(XEN) Monitor-Mwait will be used to enter C-3 state
ACPI: CPU-1 (power states: C1[C1] C2[C3] C3[C3])
(XEN) cpuid.MWAIT[.eax=40, .ebx=40, .ecx=3, .edx=1120]
(XEN) Monitor-Mwait will be used to enter C-1 state
(XEN) cpuid.MWAIT[.eax=40, .ebx=40, .ecx=3, .edx=1120]
(XEN) Monitor-Mwait will be used to enter C-3 state
(XEN) cpuid.MWAIT[.eax=40, .ebx=40, .ecx=3, .edx=1120]
(XEN) Monitor-Mwait will be used to enter C-3 state
ACPI: CPU-1 (power states: C1[C1] C2[C3] C3[C3])
(XEN) cpuid.MWAIT[.eax=40, .ebx=40, .ecx=3, .edx=1120]
(XEN) Monitor-Mwait will be used to enter C-1 state
(XEN) cpuid.MWAIT[.eax=40, .ebx=40, .ecx=3, .edx=1120]
(XEN) Monitor-Mwait will be used to enter C-3 state
(XEN) cpuid.MWAIT[.eax=40, .ebx=40, .ecx=3, .edx=1120]
(XEN) Monitor-Mwait will be used to enter C-3 state
ACPI: CPU-1 (power states: C1[C1] C2[C3] C3[C3])
(XEN) cpuid.MWAIT[.eax=40, .ebx=40, .ecx=3, .edx=1120]
(XEN) Monitor-Mwait will be used to enter C-1 state
(XEN) cpuid.MWAIT[.eax=40, .ebx=40, .ecx=3, .edx=1120]
(XEN) Monitor-Mwait will be used to enter C-3 state
(XEN) cpuid.MWAIT[.eax=40, .ebx=40, .ecx=3, .edx=1120]
(XEN) Monitor-Mwait will be used to enter C-3 state
ACPI: CPU-1 (power states: C1[C1] C2[C3] C3[C3])
(XEN) cpuid.MWAIT[.eax=40, .ebx=40, .ecx=3, .edx=1120]
(XEN) Monitor-Mwait will be used to enter C-1 state
(XEN) cpuid.MWAIT[.eax=40, .ebx=40, .ecx=3, .edx=1120]
(XEN) Monitor-Mwait will be used to enter C-3 state
(XEN) cpuid.MWAIT[.eax=40, .ebx=40, .ecx=3, .edx=1120]
(XEN) Monitor-Mwait will be used to enter C-3 state
ACPI: CPU-1 (power states: C1[C1] C2[C3] C3[C3])
(XEN) cpuid.MWAIT[.eax=40, .ebx=40, .ecx=3, .edx=1120]
(XEN) Monitor-Mwait will be used to enter C-1 state
(XEN) cpuid.MWAIT[.eax=40, .ebx=40, .ecx=3, .edx=1120]
(XEN) Monitor-Mwait will be used to enter C-3 state
(XEN) cpuid.MWAIT[.eax=40, .ebx=40, .ecx=3, .edx=1120]
(XEN) Monitor-Mwait will be used to enter C-3 state
ACPI: CPU-1 (power states: C1[C1] C2[C3] C3[C3])
initcall acpi_processor_init+0x0/0x132 returned 0 after 629629 usecs
calling acpi_container_init+0x0/0x42 @ 1
initcall acpi_container_init+0x0/0x42 returned 0 after 13724 usecs
calling acpi_thermal_init+0x0/0x7b @ 1
initcall acpi_thermal_init+0x0/0x7b returned 0 after 169 usecs
calling acpi_battery_init+0x0/0x16 @ 1
initcall acpi_battery_init+0x0/0x16 returned 0 after 30 usecs
calling 1_acpi_battery_init_async+0x0/0x3c @ 233
initcall 1_acpi_battery_init_async+0x0/0x3c returned 0 after 244 usecs
calling evtchn_init+0x0/0x7e @ 1
Event-channel device installed.
initcall evtchn_init+0x0/0x7e returned 0 after 2902 usecs
calling gntdev_init+0x0/0x3d @ 1
initcall gntdev_init+0x0/0x3d returned 0 after 117 usecs
calling pciback_init+0x0/0x15f @ 1
initcall pciback_init+0x0/0x15f returned 0 after 4695 usecs
calling blkif_init+0x0/0x171 @ 1
initcall blkif_init+0x0/0x171 returned 0 after 3660 usecs
calling blktap_init+0x0/0xa7 @ 1
blktap_device_init: blktap device major 253
blktap_ring_init: blktap ring major: 251
initcall blktap_init+0x0/0xa7 returned 0 after 10464 usecs
calling netback_init+0x0/0x207 @ 1
registering netback
initcall netback_init+0x0/0x207 returned 0 after 2961 usecs
calling hypervisor_subsys_init+0x0/0x25 @ 1
initcall hypervisor_subsys_init+0x0/0x25 returned 0 after 0 usecs
calling hyper_sysfs_init+0x0/0xf2 @ 1
initcall hyper_sysfs_init+0x0/0xf2 returned 0 after 79 usecs
calling platform_pci_module_init+0x0/0xa3 @ 1
xen-platform-pcifailed backend handshake: unrecognised magic value
initcall platform_pci_module_init+0x0/0xa3 returned -19 after 5839 usecs
calling mcelog_init+0x0/0x1b0 @ 1
alloc irq_desc for 4263 on node 0
alloc kstat_irqs on node 0
initcall mcelog_init+0x0/0x1b0 returned 0 after 6418 usecs
calling rand_initialize+0x0/0x31 @ 1
initcall rand_initialize+0x0/0x31 returned 0 after 30 usecs
calling tty_init+0x0/0xf5 @ 1
initcall tty_init+0x0/0xf5 returned 0 after 6277 usecs
calling pty_init+0x0/0x336 @ 1
initcall pty_init+0x0/0x336 returned 0 after 243 usecs
calling sysrq_init+0x0/0x25 @ 1
initcall sysrq_init+0x0/0x25 returned 0 after 14 usecs
calling xen_hvc_init+0x0/0xe2 @ 1
alloc irq_desc for 4262 on node 0
alloc kstat_irqs on node 0
initcall xen_hvc_init+0x0/0xe2 returned 0 after 6895 usecs
calling raw_init+0x0/0xe5 @ 1
initcall raw_init+0x0/0xe5 returned 0 after 149 usecs
calling hpet_init+0x0/0x6a @ 1
hpet_acpi_add: no address or irqs in _CRS
initcall hpet_init+0x0/0x6a returned 0 after 4307 usecs
calling nvram_init+0x0/0x82 @ 1
Non-volatile memory driver v1.3
initcall nvram_init+0x0/0x82 returned 0 after 2886 usecs
calling agp_init+0x0/0x26 @ 1
Linux agpgart interface v0.103
initcall agp_init+0x0/0x26 returned 0 after 2792 usecs
calling agp_intel_init+0x0/0x29 @ 1
initcall agp_intel_init+0x0/0x29 returned 0 after 111 usecs
calling agp_sis_init+0x0/0x29 @ 1
initcall agp_sis_init+0x0/0x29 returned 0 after 133 usecs
calling agp_via_init+0x0/0x29 @ 1
initcall agp_via_init+0x0/0x29 returned 0 after 101 usecs
calling init_tis+0x0/0x91 @ 1
initcall init_tis+0x0/0x91 returned 0 after 65 usecs
calling cn_proc_init+0x0/0x3d @ 1
initcall cn_proc_init+0x0/0x3d returned 0 after 45 usecs
calling serial8250_init+0x0/0x143 @ 1
Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled
async_waiting @ 1
async_continuing @ 1 after 10 usec
(XEN) irq.c:1139:d0 Cannot bind IRQ 4 to guest. In use by
''ns16550''.
(XEN) irq.c:1139:d0 Cannot bind IRQ 2 to guest. In use by
''cascade''.
(XEN) irq.c:1139:d0 Cannot bind IRQ 4 to guest. In use by
''ns16550''.
(XEN) irq.c:1139:d0 Cannot bind IRQ 2 to guest. In use by
''cascade''.
async_waiting @ 1
async_continuing @ 1 after 1 usec
(XEN) irq.c:1139:d0 Cannot bind IRQ 4 to guest. In use by
''ns16550''.
(XEN) irq.c:1139:d0 Cannot bind IRQ 2 to guest. In use by
''cascade''.
(XEN) irq.c:1139:d0 Cannot bind IRQ 4 to guest. In use by
''ns16550''.
(XEN) irq.c:1139:d0 Cannot bind IRQ 2 to guest. In use by
''cascade''.
serial8250: ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A
initcall serial8250_init+0x0/0x143 returned 0 after 308270 usecs
calling serial8250_pnp_init+0x0/0x12 @ 1
00:0b: ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A
initcall serial8250_pnp_init+0x0/0x12 returned 0 after 5240 usecs
calling serial8250_pci_init+0x0/0x1b @ 1
initcall serial8250_pci_init+0x0/0x1b returned 0 after 114 usecs
calling init_kgdboc+0x0/0x16 @ 1
initcall init_kgdboc+0x0/0x16 returned 0 after 0 usecs
calling topology_sysfs_init+0x0/0x63 @ 1
initcall topology_sysfs_init+0x0/0x63 returned 0 after 470 usecs
calling brd_init+0x0/0x16d @ 1
brd: module loaded
initcall brd_init+0x0/0x16d returned 0 after 8259 usecs
calling loop_init+0x0/0x197 @ 1
loop: module loaded
initcall loop_init+0x0/0x197 returned 0 after 4968 usecs
calling init_kgdbts+0x0/0x16 @ 1
initcall init_kgdbts+0x0/0x16 returned 0 after 0 usecs
calling mac_hid_init+0x0/0xd5 @ 1
input: Macintosh mouse button emulation as /devices/virtual/input/input2
initcall mac_hid_init+0x0/0xd5 returned 0 after 6552 usecs
calling scsi_dh_init+0x0/0x3f @ 1
initcall scsi_dh_init+0x0/0x3f returned 0 after 1 usecs
calling init_sd+0x0/0x17b @ 1
initcall init_sd+0x0/0x17b returned 0 after 420 usecs
calling init_sr+0x0/0x49 @ 1
initcall init_sr+0x0/0x49 returned 0 after 51 usecs
calling init_sg+0x0/0x123 @ 1
initcall init_sg+0x0/0x123 returned 0 after 136 usecs
calling ahci_init+0x0/0x1b @ 1
ahci 0000:00:1f.2: version 3.0
xen: registering gsi 19 triggering 0 polarity 1
alloc irq_desc for 19 on node 0
alloc kstat_irqs on node 0
xen: --> irq=19
ahci 0000:00:1f.2: PCI INT B -> GSI 19 (level, low) -> IRQ 19
alloc irq_desc for 4261 on node 0
alloc kstat_irqs on node 0
ahci: SSS flag set, parallel bus scan disabled
ahci 0000:00:1f.2: AHCI 0001.0200 32 slots 6 ports 3 Gbps 0x3f impl SATA
mode
ahci 0000:00:1f.2: flags: 64bit ncq sntf stag pm led clo pio slum part
ccc ems sxs
ahci 0000:00:1f.2: setting latency timer to 64
scsi0 : ahci
scsi1 : ahci
scsi2 : ahci
scsi3 : ahci
scsi4 : ahci
scsi5 : ahci
ata1: SATA max UDMA/133 abar m2048@0xfbbd6000 port 0xfbbd6100 irq 4261
ata2: SATA max UDMA/133 abar m2048@0xfbbd6000 port 0xfbbd6180 irq 4261
ata3: SATA max UDMA/133 irq_stat 0x00400040, connection status changed
irq 4261
ata4: SATA max UDMA/133 irq_stat 0x00400040, connection status changed
irq 4261
ata5: SATA max UDMA/133 abar m2048@0xfbbd6000 port 0xfbbd6300 irq 4261
ata6: SATA max UDMA/133 abar m2048@0xfbbd6000 port 0xfbbd6380 irq 4261
calling 2_async_port_probe+0x0/0xc9 @ 233
initcall ahci_init+0x0/0x1b returned 0 after 109920 usecs
calling piix_init+0x0/0x29 @ 1
initcall piix_init+0x0/0x29 returned 0 after 136 usecs
calling fixed_mdio_bus_init+0x0/0xd0 @ 1
Fixed MDIO Bus: probed
initcall fixed_mdio_bus_init+0x0/0xd0 returned 0 after 189 usecs
calling net_olddevs_init+0x0/0x9e @ 1
initcall net_olddevs_init+0x0/0x9e returned 0 after 3 usecs
calling netif_init+0x0/0x6a @ 1
initcall netif_init+0x0/0x6a returned 0 after 0 usecs
calling cdrom_init+0x0/0x6a @ 1
initcall cdrom_init+0x0/0x6a returned 0 after 195 usecs
calling mon_init+0x0/0x117 @ 1
initcall mon_init+0x0/0x117 returned 0 after 283 usecs
calling ehci_hcd_init+0x0/0xc0 @ 1
ehci_hcd: USB 2.0 ''Enhanced'' Host Controller (EHCI) Driver
xen: registering gsi 18 triggering 0 polarity 1
alloc irq_desc for 18 on node 0
alloc kstat_irqs on node 0
xen: --> irq=18
ehci_hcd 0000:00:1a.7: PCI INT C -> GSI 18 (level, low) -> IRQ 18
ehci_hcd 0000:00:1a.7: setting latency timer to 64
ehci_hcd 0000:00:1a.7: EHCI Host Controller
ehci_hcd 0000:00:1a.7: new USB bus registered, assigned bus number 1
ehci_hcd 0000:00:1a.7: debug port 1
ehci_hcd 0000:00:1a.7: cache line size of 32 is not supported
ehci_hcd 0000:00:1a.7: irq 18, io mem 0xfbbde000
ehci_hcd 0000:00:1a.7: USB 2.0 started, EHCI 1.00
usb usb1: New USB device found, idVendor=1d6b, idProduct=0002
usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
usb usb1: Product: EHCI Host Controller
usb usb1: Manufacturer: Linux 2.6.32.13 ehci_hcd
usb usb1: SerialNumber: 0000:00:1a.7
usb usb1: configuration #1 chosen from 1 choice
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 6 ports detected
xen: registering gsi 23 triggering 0 polarity 1
alloc irq_desc for 23 on node 0
alloc kstat_irqs on node 0
xen: --> irq=23
ehci_hcd 0000:00:1d.7: PCI INT A -> GSI 23 (level, low) -> IRQ 23
ehci_hcd 0000:00:1d.7: setting latency timer to 64
ehci_hcd 0000:00:1d.7: EHCI Host Controller
ehci_hcd 0000:00:1d.7: new USB bus registered, assigned bus number 2
ehci_hcd 0000:00:1d.7: debug port 1
ehci_hcd 0000:00:1d.7: cache line size of 32 is not supported
ehci_hcd 0000:00:1d.7: irq 23, io mem 0xfbbdc000
ehci_hcd 0000:00:1d.7: USB 2.0 started, EHCI 1.00
usb usb2: New USB device found, idVendor=1d6b, idProduct=0002
usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1
usb usb2: Product: EHCI Host Controller
usb usb2: Manufacturer: Linux 2.6.32.13 ehci_hcd
usb usb2: SerialNumber: 0000:00:1d.7
usb usb2: configuration #1 chosen from 1 choice
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 6 ports detected
initcall ehci_hcd_init+0x0/0xc0 returned 0 after 36306 usecs
calling ohci_hcd_mod_init+0x0/0x92 @ 1
ohci_hcd: USB 1.1 ''Open'' Host Controller (OHCI) Driver
initcall ohci_hcd_mod_init+0x0/0x92 returned 0 after 121 usecs
calling uhci_hcd_init+0x0/0xc0 @ 1
uhci_hcd: USB Universal Host Controller Interface driver
xen: registering gsi 16 triggering 0 polarity 1
xen_allocate_pirq: returning irq 16 for gsi 16
xen: --> irq=16
Already setup the GSI :16
uhci_hcd 0000:00:1a.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
uhci_hcd 0000:00:1a.0: setting latency timer to 64
uhci_hcd 0000:00:1a.0: UHCI Host Controller
uhci_hcd 0000:00:1a.0: new USB bus registered, assigned bus number 3
uhci_hcd 0000:00:1a.0: irq 16, io base 0x0000ac00
usb usb3: New USB device found, idVendor=1d6b, idProduct=0001
usb usb3: New USB device strings: Mfr=3, Product=2, SerialNumber=1
usb usb3: Product: UHCI Host Controller
usb usb3: Manufacturer: Linux 2.6.32.13 uhci_hcd
usb usb3: SerialNumber: 0000:00:1a.0
usb usb3: configuration #1 chosen from 1 choice
hub 3-0:1.0: USB hub found
hub 3-0:1.0: 2 ports detected
xen: registering gsi 21 triggering 0 polarity 1
alloc irq_desc for 21 on node 0
alloc kstat_irqs on node 0
xen: --> irq=21
uhci_hcd 0000:00:1a.1: PCI INT B -> GSI 21 (level, low) -> IRQ 21
uhci_hcd 0000:00:1a.1: setting latency timer to 64
uhci_hcd 0000:00:1a.1: UHCI Host Controller
uhci_hcd 0000:00:1a.1: new USB bus registered, assigned bus number 4
uhci_hcd 0000:00:1a.1: irq 21, io base 0x0000a880
usb usb4: New USB device found, idVendor=1d6b, idProduct=0001
usb usb4: New USB device strings: Mfr=3, Product=2, SerialNumber=1
usb usb4: Product: UHCI Host Controller
usb usb4: Manufacturer: Linux 2.6.32.13 uhci_hcd
usb usb4: SerialNumber: 0000:00:1a.1
usb usb4: configuration #1 chosen from 1 choice
hub 4-0:1.0: USB hub found
hub 4-0:1.0: 2 ports detected
xen: registering gsi 19 triggering 0 polarity 1
xen_allocate_pirq: returning irq 19 for gsi 19
xen: --> irq=19
Already setup the GSI :19
uhci_hcd 0000:00:1a.2: PCI INT D -> GSI 19 (level, low) -> IRQ 19
uhci_hcd 0000:00:1a.2: setting latency timer to 64
uhci_hcd 0000:00:1a.2: UHCI Host Controller
uhci_hcd 0000:00:1a.2: new USB bus registered, assigned bus number 5
uhci_hcd 0000:00:1a.2: irq 19, io base 0x0000a800
usb usb5: New USB device found, idVendor=1d6b, idProduct=0001
usb usb5: New USB device strings: Mfr=3, Product=2, SerialNumber=1
usb usb5: Product: UHCI Host Controller
usb usb5: Manufacturer: Linux 2.6.32.13 uhci_hcd
usb usb5: SerialNumber: 0000:00:1a.2
usb usb5: configuration #1 chosen from 1 choice
hub 5-0:1.0: USB hub found
hub 5-0:1.0: 2 ports detected
xen: registering gsi 23 triggering 0 polarity 1
xen_allocate_pirq: returning irq 23 for gsi 23
xen: --> irq=23
Already setup the GSI :23
uhci_hcd 0000:00:1d.0: PCI INT A -> GSI 23 (level, low) -> IRQ 23
uhci_hcd 0000:00:1d.0: setting latency timer to 64
uhci_hcd 0000:00:1d.0: UHCI Host Controller
uhci_hcd 0000:00:1d.0: new USB bus registered, assigned bus number 6
uhci_hcd 0000:00:1d.0: irq 23, io base 0x0000a480
usb usb6: New USB device found, idVendor=1d6b, idProduct=0001
usb usb6: New USB device strings: Mfr=3, Product=2, SerialNumber=1
usb usb6: Product: UHCI Host Controller
usb usb6: Manufacturer: Linux 2.6.32.13 uhci_hcd
usb usb6: SerialNumber: 0000:00:1d.0
usb usb6: configuration #1 chosen from 1 choice
hub 6-0:1.0: USB hub found
hub 6-0:1.0: 2 ports detected
xen: registering gsi 19 triggering 0 polarity 1
xen_allocate_pirq: returning irq 19 for gsi 19
xen: --> irq=19
Already setup the GSI :19
uhci_hcd 0000:00:1d.1: PCI INT B -> GSI 19 (level, low) -> IRQ 19
uhci_hcd 0000:00:1d.1: setting latency timer to 64
uhci_hcd 0000:00:1d.1: UHCI Host Controller
uhci_hcd 0000:00:1d.1: new USB bus registered, assigned bus number 7
uhci_hcd 0000:00:1d.1: irq 19, io base 0x0000a400
usb usb7: New USB device found, idVendor=1d6b, idProduct=0001
usb usb7: New USB device strings: Mfr=3, Product=2, SerialNumber=1
usb usb7: Product: UHCI Host Controller
usb usb7: Manufacturer: Linux 2.6.32.13 uhci_hcd
usb usb7: SerialNumber: 0000:00:1d.1
usb usb7: configuration #1 chosen from 1 choice
hub 7-0:1.0: USB hub found
hub 7-0:1.0: 2 ports detected
xen: registering gsi 18 triggering 0 polarity 1
xen_allocate_pirq: returning irq 18 for gsi 18
xen: --> irq=18
Already setup the GSI :18
uhci_hcd 0000:00:1d.2: PCI INT C -> GSI 18 (level, low) -> IRQ 18
uhci_hcd 0000:00:1d.2: setting latency timer to 64
uhci_hcd 0000:00:1d.2: UHCI Host Controller
uhci_hcd 0000:00:1d.2: new USB bus registered, assigned bus number 8
uhci_hcd 0000:00:1d.2: irq 18, io base 0x0000a080
usb usb8: New USB device found, idVendor=1d6b, idProduct=0001
usb usb8: New USB device strings: Mfr=3, Product=2, SerialNumber=1
usb usb8: Product: UHCI Host Controller
usb usb8: Manufacturer: Linux 2.6.32.13 uhci_hcd
usb usb8: SerialNumber: 0000:00:1d.2
usb usb8: configuration #1 chosen from 1 choice
hub 8-0:1.0: USB hub found
hub 8-0:1.0: 2 ports detected
initcall uhci_hcd_init+0x0/0xc0 returned 0 after 27682 usecs
calling i8042_init+0x0/0x3a7 @ 1
PNP: No PS/2 controller found. Probing ports directly.
serio: i8042 KBD port at 0x60,0x64 irq 1
serio: i8042 AUX port at 0x60,0x64 irq 12
initcall i8042_init+0x0/0x3a7 returned 0 after 3611 usecs
calling serport_init+0x0/0x34 @ 1
initcall serport_init+0x0/0x34 returned 0 after 1 usecs
calling mousedev_init+0x0/0x62 @ 1
mice: PS/2 mouse device common for all mice
initcall mousedev_init+0x0/0x62 returned 0 after 614 usecs
calling evdev_init+0x0/0x12 @ 1
initcall evdev_init+0x0/0x12 returned 0 after 447 usecs
calling atkbd_init+0x0/0x27 @ 1
initcall atkbd_init+0x0/0x27 returned 0 after 105 usecs
calling psmouse_init+0x0/0x74 @ 1
initcall psmouse_init+0x0/0x74 returned 0 after 442 usecs
calling xenkbd_init+0x0/0x5d @ 1
initcall xenkbd_init+0x0/0x5d returned -19 after 0 usecs
calling cmos_init+0x0/0x6d @ 1
rtc_cmos 00:03: RTC can wake from S4
rtc_cmos 00:03: rtc core: registered rtc_cmos as rtc0
rtc0: alarms up to one month, y3k, 114 bytes nvram
initcall cmos_init+0x0/0x6d returned 0 after 619 usecs
calling dm_init+0x0/0x49 @ 1
device-mapper: uevent: version 1.0.3
device-mapper: ioctl: 4.15.0-ioctl (2009-04-01) initialised:
dm-devel@redhat.com
initcall dm_init+0x0/0x49 returned 0 after 1824 usecs
calling dm_snapshot_init+0x0/0x26a @ 1
initcall dm_snapshot_init+0x0/0x26a returned 0 after 898 usecs
calling dm_mirror_init+0x0/0x79 @ 1
initcall dm_mirror_init+0x0/0x79 returned 0 after 252 usecs
calling dm_dirty_log_init+0x0/0x59 @ 1
initcall dm_dirty_log_init+0x0/0x59 returned 0 after 16 usecs
calling dm_zero_init+0x0/0x31 @ 1
initcall dm_zero_init+0x0/0x31 returned 0 after 1 usecs
calling init_ladder+0x0/0x12 @ 1
cpuidle: using governor ladder
initcall init_ladder+0x0/0x12 returned 0 after 19 usecs
calling init_menu+0x0/0x12 @ 1
cpuidle: using governor menu
initcall init_menu+0x0/0x12 returned 0 after 2 usecs
calling efivars_init+0x0/0x213 @ 1
initcall efivars_init+0x0/0x213 returned -19 after 0 usecs
calling hid_init+0x0/0x66 @ 1
initcall hid_init+0x0/0x66 returned 0 after 175 usecs
calling a4_init+0x0/0x1b @ 1
initcall a4_init+0x0/0x1b returned 0 after 68 usecs
calling apple_init+0x0/0x38 @ 1
initcall apple_init+0x0/0x38 returned 0 after 84 usecs
calling belkin_init+0x0/0x1b @ 1
initcall belkin_init+0x0/0x1b returned 0 after 65 usecs
calling ch_init+0x0/0x1b @ 1
initcall ch_init+0x0/0x1b returned 0 after 59 usecs
calling ch_init+0x0/0x1b @ 1
initcall ch_init+0x0/0x1b returned 0 after 69 usecs
calling cp_init+0x0/0x1b @ 1
initcall cp_init+0x0/0x1b returned 0 after 65 usecs
calling dr_init+0x0/0x1b @ 1
initcall dr_init+0x0/0x1b returned 0 after 56 usecs
calling ez_init+0x0/0x1b @ 1
initcall ez_init+0x0/0x1b returned 0 after 57 usecs
calling gyration_init+0x0/0x1b @ 1
initcall gyration_init+0x0/0x1b returned 0 after 52 usecs
calling ks_init+0x0/0x1b @ 1
initcall ks_init+0x0/0x1b returned 0 after 98 usecs
calling kye_init+0x0/0x1b @ 1
initcall kye_init+0x0/0x1b returned 0 after 60 usecs
calling lg_init+0x0/0x1b @ 1
initcall lg_init+0x0/0x1b returned 0 after 73 usecs
calling ms_init+0x0/0x1b @ 1
initcall ms_init+0x0/0x1b returned 0 after 68 usecs
calling mr_init+0x0/0x1b @ 1
initcall mr_init+0x0/0x1b returned 0 after 64 usecs
calling ntrig_init+0x0/0x1b @ 1
initcall ntrig_init+0x0/0x1b returned 0 after 72 usecs
calling pl_init+0x0/0x1b @ 1
initcall pl_init+0x0/0x1b returned 0 after 64 usecs
calling pl_init+0x0/0x1b @ 1
initcall pl_init+0x0/0x1b returned 0 after 71 usecs
calling samsung_init+0x0/0x1b @ 1
initcall samsung_init+0x0/0x1b returned 0 after 59 usecs
calling sjoy_init+0x0/0x1b @ 1
initcall sjoy_init+0x0/0x1b returned 0 after 64 usecs
calling sony_init+0x0/0x1b @ 1
initcall sony_init+0x0/0x1b returned 0 after 70 usecs
calling sp_init+0x0/0x1b @ 1
initcall sp_init+0x0/0x1b returned 0 after 57 usecs
calling ga_init+0x0/0x1b @ 1
initcall ga_init+0x0/0x1b returned 0 after 52 usecs
calling tm_init+0x0/0x1b @ 1
initcall tm_init+0x0/0x1b returned 0 after 52 usecs
calling ts_init+0x0/0x1b @ 1
initcall ts_init+0x0/0x1b returned 0 after 57 usecs
calling twinhan_init+0x0/0x1b @ 1
initcall twinhan_init+0x0/0x1b returned 0 after 85 usecs
calling zp_init+0x0/0x1b @ 1
initcall zp_init+0x0/0x1b returned 0 after 70 usecs
calling hid_init+0x0/0xcb @ 1
usbcore: registered new interface driver hiddev
usbcore: registered new interface driver usbhid
usbhid: v2.6:USB HID core driver
initcall hid_init+0x0/0xcb returned 0 after 446 usecs
calling flow_cache_init+0x0/0x1b0 @ 1
initcall flow_cache_init+0x0/0x1b0 returned 0 after 350 usecs
calling blackhole_module_init+0x0/0x12 @ 1
initcall blackhole_module_init+0x0/0x12 returned 0 after 2 usecs
calling init_cgroup_cls+0x0/0x12 @ 1
initcall init_cgroup_cls+0x0/0x12 returned 0 after 21 usecs
calling nf_conntrack_standalone_init+0x0/0x12 @ 1
nf_conntrack version 0.5.0 (16384 buckets, 65536 max)
CONFIG_NF_CT_ACCT is deprecated and will be removed soon. Please use
nf_conntrack.acct=1 kernel parameter, acct=1 nf_conntrack module option
or
sysctl net.netfilter.nf_conntrack_acct=1 to enable it.
initcall nf_conntrack_standalone_init+0x0/0x12 returned 0 after 22301
usecs
calling xt_init+0x0/0x190 @ 1
initcall xt_init+0x0/0x190 returned 0 after 42 usecs
calling tcpudp_mt_init+0x0/0x17 @ 1
initcall tcpudp_mt_init+0x0/0x17 returned 0 after 25 usecs
calling conntrack_mt_init+0x0/0x17 @ 1
initcall conntrack_mt_init+0x0/0x17 returned 0 after 2 usecs
calling state_mt_init+0x0/0x17 @ 1
initcall state_mt_init+0x0/0x17 returned 0 after 2 usecs
calling sysctl_ipv4_init+0x0/0x4e @ 1
initcall sysctl_ipv4_init+0x0/0x4e returned 0 after 2354 usecs
calling init_syncookies+0x0/0x19 @ 1
initcall init_syncookies+0x0/0x19 returned 0 after 44 usecs
calling ipv4_netfilter_init+0x0/0x17 @ 1
initcall ipv4_netfilter_init+0x0/0x17 returned 0 after 16 usecs
calling nf_conntrack_l3proto_ipv4_init+0x0/0x12d @ 1
initcall nf_conntrack_l3proto_ipv4_init+0x0/0x12d returned 0 after 506
usecs
calling nf_defrag_init+0x0/0x17 @ 1
initcall nf_defrag_init+0x0/0x17 returned 0 after 2 usecs
calling ip_tables_init+0x0/0xaf @ 1
ip_tables: (C) 2000-2006 Netfilter Core Team
initcall ip_tables_init+0x0/0xaf returned 0 after 44 usecs
calling iptable_filter_init+0x0/0x6c @ 1
initcall iptable_filter_init+0x0/0x6c returned 0 after 136 usecs
calling reject_tg_init+0x0/0x12 @ 1
initcall reject_tg_init+0x0/0x12 returned 0 after 3 usecs
calling cubictcp_register+0x0/0x65 @ 1
TCP cubic registered
initcall cubictcp_register+0x0/0x65 returned 0 after 3 usecs
calling xfrm_user_init+0x0/0x4d @ 1
Initializing XFRM netlink socket
initcall xfrm_user_init+0x0/0x4d returned 0 after 49 usecs
calling packet_init+0x0/0x47 @ 1
NET: Registered protocol family 17
initcall packet_init+0x0/0x47 returned 0 after 45 usecs
calling dsa_init_module+0x0/0x14 @ 1
initcall dsa_init_module+0x0/0x14 returned 0 after 1 usecs
calling edsa_init_module+0x0/0x14 @ 1
initcall edsa_init_module+0x0/0x14 returned 0 after 1 usecs
calling trailer_init_module+0x0/0x14 @ 1
initcall trailer_init_module+0x0/0x14 returned 0 after 1 usecs
calling mv88e6060_init+0x0/0x14 @ 1
initcall mv88e6060_init+0x0/0x14 returned 0 after 14 usecs
calling mv88e6123_61_65_init+0x0/0x14 @ 1
initcall mv88e6123_61_65_init+0x0/0x14 returned 0 after 1 usecs
calling mv88e6131_init+0x0/0x14 @ 1
initcall mv88e6131_init+0x0/0x14 returned 0 after 1 usecs
calling dsa_init_module+0x0/0x12 @ 1
initcall dsa_init_module+0x0/0x12 returned 0 after 73 usecs
calling dcbnl_init+0x0/0x32 @ 1
initcall dcbnl_init+0x0/0x32 returned 0 after 0 usecs
calling mce_debugfs_init+0x0/0x3b @ 1
initcall mce_debugfs_init+0x0/0x3b returned 0 after 46 usecs
calling severities_debugfs_init+0x0/0x3b @ 1
initcall severities_debugfs_init+0x0/0x3b returned 0 after 18 usecs
calling hpet_insert_resource+0x0/0x23 @ 1
initcall hpet_insert_resource+0x0/0x23 returned 0 after 3 usecs
calling update_mp_table+0x0/0x689 @ 1
initcall update_mp_table+0x0/0x689 returned 0 after 0 usecs
calling lapic_insert_resource+0x0/0x40 @ 1
initcall lapic_insert_resource+0x0/0x40 returned -1 after 0 usecs
initcall lapic_insert_resource+0x0/0x40 returned with error code -1
calling init_lapic_nmi_sysfs+0x0/0x39 @ 1
initcall init_lapic_nmi_sysfs+0x0/0x39 returned 0 after 0 usecs
calling io_apic_bug_finalize+0x0/0x1b @ 1
initcall io_apic_bug_finalize+0x0/0x1b returned 0 after 0 usecs
calling check_early_ioremap_leak+0x0/0x67 @ 1
initcall check_early_ioremap_leak+0x0/0x67 returned 0 after 0 usecs
calling pat_memtype_list_init+0x0/0x29 @ 1
initcall pat_memtype_list_init+0x0/0x29 returned 0 after 19 usecs
calling sched_init_debug+0x0/0x24 @ 1
initcall sched_init_debug+0x0/0x24 returned 0 after 18 usecs
calling init_oops_id+0x0/0x36 @ 1
initcall init_oops_id+0x0/0x36 returned 0 after 8 usecs
calling disable_boot_consoles+0x0/0x5c @ 1
initcall disable_boot_consoles+0x0/0x5c returned 0 after 0 usecs
calling pm_qos_power_init+0x0/0xca @ 1
initcall pm_qos_power_init+0x0/0xca returned 0 after 352 usecs
calling test_suspend+0x0/0x19d @ 1
initcall test_suspend+0x0/0x19d returned 0 after 0 usecs
calling software_resume+0x0/0x20f @ 1
PM: Resume from disk failed.
initcall software_resume+0x0/0x20f returned -2 after 15 usecs
initcall software_resume+0x0/0x20f returned with error code -2
calling debugfs_kprobe_init+0x0/0x8e @ 1
initcall debugfs_kprobe_init+0x0/0x8e returned 0 after 111 usecs
calling taskstats_init+0x0/0x95 @ 1
registered taskstats version 1
initcall taskstats_init+0x0/0x95 returned 0 after 35 usecs
calling clear_boot_tracer+0x0/0x2d @ 1
initcall clear_boot_tracer+0x0/0x2d returned 0 after 0 usecs
calling fail_page_alloc_debugfs+0x0/0xe4 @ 1
initcall fail_page_alloc_debugfs+0x0/0xe4 returned 0 after 193 usecs
calling max_swapfiles_check+0x0/0x8 @ 1
initcall max_swapfiles_check+0x0/0x8 returned 0 after 0 usecs
calling failslab_debugfs_init+0x0/0x6b @ 1
initcall failslab_debugfs_init+0x0/0x6b returned 0 after 135 usecs
calling init_ima+0x0/0x1a @ 1
No TPM chip found, activating TPM-bypass!
initcall init_ima+0x0/0x1a returned 0 after 615 usecs
calling fail_make_request_debugfs+0x0/0x19 @ 1
initcall fail_make_request_debugfs+0x0/0x19 returned 0 after 306 usecs
calling random32_reseed+0x0/0xa9 @ 1
initcall random32_reseed+0x0/0xa9 returned 0 after 147 usecs
calling pci_resource_alignment_sysfs_init+0x0/0x19 @ 1
initcall pci_resource_alignment_sysfs_init+0x0/0x19 returned 0 after 6
usecs
calling pci_sysfs_init+0x0/0x4c @ 1
initcall pci_sysfs_init+0x0/0x4c returned 0 after 3427 usecs
calling boot_wait_for_devices+0x0/0x19 @ 1
initcall boot_wait_for_devices+0x0/0x19 returned 0 after 1 usecs
calling regulator_init_complete+0x0/0x14b @ 1
initcall regulator_init_complete+0x0/0x14b returned 0 after 16 usecs
calling seqgen_init+0x0/0xf @ 1
initcall seqgen_init+0x0/0xf returned 0 after 46 usecs
calling late_resume_init+0x0/0x124 @ 1
Magic number: 10:134:278
tty tty15: hash matches
initcall late_resume_init+0x0/0x124 returned 0 after 92 usecs
calling scsi_complete_async_scans+0x0/0x148 @ 1
initcall scsi_complete_async_scans+0x0/0x148 returned 0 after 0 usecs
calling rtc_hctosys+0x0/0x152 @ 1
usb 2-1: new high speed USB device using ehci_hcd and address 2
usb 2-1: New USB device found, idVendor=2001, idProduct=f103
usb 2-1: New USB device strings: Mfr=0, Product=0, SerialNumber=0
usb 2-1: configuration #1 chosen from 1 choice
hub 2-1:1.0: USB hub found
hub 2-1:1.0: 7 ports detected
usb 2-1.2: new full speed USB device using ehci_hcd and address 4
usb 2-1.2: New USB device found, idVendor=04e8, idProduct=326c
usb 2-1.2: New USB device strings: Mfr=1, Product=2, SerialNumber=3
usb 2-1.2: Product: Samsung ML-2010
usb 2-1.2: Manufacturer: Samsung
usb 2-1.2: SerialNumber: 3A61BKCL919879R.
usb 2-1.2: configuration #1 chosen from 1 choice
usb 6-2: new low speed USB device using uhci_hcd and address 2
usb 6-2: New USB device found, idVendor=05af, idProduct=0408
usb 6-2: New USB device strings: Mfr=0, Product=2, SerialNumber=0
usb 6-2: Product: 2.4G USB RF KeyBoard
usb 6-2: configuration #1 chosen from 1 choice
input: 2.4G USB RF KeyBoard
as /devices/pci0000:00/0000:00:1d.0/usb6/6-2/6-2:1.0/input/input3
generic-usb 0003:05AF:0408.0001: input,hidraw0: USB HID v1.10 Keyboard
[2.4G USB RF KeyBoard] on usb-0000:00:1d.0-2/input0
input: 2.4G USB RF KeyBoard
as /devices/pci0000:00/0000:00:1d.0/usb6/6-2/6-2:1.1/input/input4
generic-usb 0003:05AF:0408.0002: input,hidraw1: USB HID v1.10 Mouse
[2.4G USB RF KeyBoard] on usb-0000:00:1d.0-2/input1
input: 2.4G USB RF KeyBoard
as /devices/pci0000:00/0000:00:1d.0/usb6/6-2/6-2:1.2/input/input5
rtc_cmos 00:03: setting system clock to 2010-05-30 11:17:51 UTC
(1275218271)
initcall rtc_hctosys+0x0/0x152 returned 0 after 1682629 usecs
calling memmap_init+0x0/0xa3 @ 1
calling 3_async_port_probe+0x0/0xc9 @ 261
generic-usb 0003:05AF:0408.0003: input,hiddev96,hidraw2: USB HID v1.10
Device [2.4G USB RF KeyBoard] on usb-0000:00:1d.0-2/input2
initcall memmap_init+0x0/0xa3 returned 0 after 811 usecs
calling pci_mmcfg_late_insert_resources+0x0/0x163 @ 1
initcall pci_mmcfg_late_insert_resources+0x0/0x163 returned 0 after 8
usecs
calling init_net_drop_monitor+0x0/0x17e @ 1
Initalizing network drop monitor service
initcall init_net_drop_monitor+0x0/0x17e returned 0 after 290 usecs
calling tcp_congestion_default+0x0/0x12 @ 1
initcall tcp_congestion_default+0x0/0x12 returned 0 after 1 usecs
calling initialize_hashrnd+0x0/0x19 @ 1
initcall initialize_hashrnd+0x0/0x19 returned 0 after 7 usecs
async_waiting @ 1
async_waiting @ 261
calling 4_async_port_probe+0x0/0xc9 @ 262
calling 5_async_port_probe+0x0/0xc9 @ 263
async_waiting @ 263
calling 6_async_port_probe+0x0/0xc9 @ 264
async_waiting @ 264
calling 7_async_port_probe+0x0/0xc9 @ 265
async_waiting @ 265
async_waiting @ 262
ata1: SATA link down (SStatus 0 SControl 300)
async_waiting @ 233
async_continuing @ 233 after 3 usec
initcall 2_async_port_probe+0x0/0xc9 returned 0 after 313154 usecs
async_continuing @ 261 after 236544 usec
ata2: SATA link down (SStatus 0 SControl 300)
async_waiting @ 261
async_continuing @ 261 after 1 usec
initcall 3_async_port_probe+0x0/0xc9 returned 0 after 555507 usecs
async_continuing @ 262 after 536879 usec
ata3: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
ata3.00: ATA-8: WDC WD7501AALS-00J7B1, 05.00K05, max UDMA/133
ata3.00: 1465149168 sectors, multi 0: LBA48 NCQ (depth 31/32), AA
ata3.00: configured for UDMA/133
async_waiting @ 262
async_continuing @ 262 after 1 usec
scsi 2:0:0:0: Direct-Access ATA WDC WD7501AALS-0 05.0 PQ: 0
ANSI: 5
calling 8_sd_probe_async+0x0/0x1e3 @ 261
sd 2:0:0:0: Attached scsi generic sg0 type 0
initcall 4_async_port_probe+0x0/0xc9 returned 0 after 1292146 usecs
async_continuing @ 263 after 1312855 usec
sd 2:0:0:0: [sda] 1465149168 512-byte logical blocks: (750 GB/698 GiB)
sd 2:0:0:0: [sda] Write Protect is off
sd 2:0:0:0: [sda] Mode Sense: 00 3a 00 00
sd 2:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn''t
support DPO or FUA
sda: sda1 sda2 sda3
sd 2:0:0:0: [sda] Attached SCSI disk
initcall 8_sd_probe_async+0x0/0x1e3 returned 0 after 38221 usecs
ata4: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata4.00: ATAPI: HL-DT-STDVD-RAM GH22NS30, 1.01, max UDMA/100
ata4.00: configured for UDMA/100
async_waiting @ 263
async_continuing @ 263 after 2 usec
scsi 3:0:0:0: CD-ROM HL-DT-ST DVD-RAM GH22NS30 1.01 PQ: 0
ANSI: 5
sr0: scsi3-mmc drive: 48x/48x writer dvd-ram cd/rw xa/form2 cdda tray
Uniform CD-ROM driver Revision: 3.20
sr 3:0:0:0: Attached scsi CD-ROM sr0
sr 3:0:0:0: Attached scsi generic sg1 type 5
initcall 5_async_port_probe+0x0/0xc9 returned 0 after 2200976 usecs
async_continuing @ 264 after 2206705 usec
async/2 used greatest stack depth: 4248 bytes left
ata5: SATA link down (SStatus 0 SControl 300)
async_waiting @ 264
async_continuing @ 264 after 1 usec
initcall 6_async_port_probe+0x0/0xc9 returned 0 after 2523975 usecs
async_continuing @ 265 after 2529786 usec
ata6: SATA link down (SStatus 0 SControl 300)
async_waiting @ 265
async_continuing @ 265 after 1 usec
initcall 7_async_port_probe+0x0/0xc9 returned 0 after 2847040 usecs
async_continuing @ 1 after 2919764 usec
Freeing unused kernel memory: 3380k freed
Write protecting the kernel read-only data: 7004k
mLoading, please wait...
calling i2c_init+0x0/0x70 [i2c_core] @ 297
initcall i2c_init+0x0/0x70 [i2c_core] returned 0 after 220 usecs
calling nvidiafb_init+0x0/0x25 [nvidiafb] @ 297
nvidiafb 0000:01:00.0: enabling device (0140 -> 0143)
xen: registering gsi 16 triggering 0 polarity 1
xen_allocate_pirq: returning irq 16 for gsi 16
xen: --> irq=16
Already setup the GSI :16
nvidiafb 0000:01:00.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
nvidiafb: Device ID: 10de042f
nvidiafb: unknown NV_ARCH
xen: registering gsi 16 triggering 0 polarity 1
xen_allocate_pirq: returning irq 16 for gsi 16
xen: --> irq=16
Already setup the GSI :16
nvidiafb 0000:03:00.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
nvidiafb: Device ID: 10de06fd
nvidiafb: unknown NV_ARCH
initcall nvidiafb_init+0x0/0x25 [nvidiafb] returned 0 after 67706 usecs
calling megasas_init+0x0/0x16f [megaraid_sas] @ 666
megasas: 00.00.04.01 Thu July 24 11:41:51 PST 2008
megasas: 0x1028:0x0015:0x1028:0x1f03: bus 5:slot 14:func 0
xen: registering gsi 18 triggering 0 polarity 1
xen_allocate_pirq: returning irq 18 for gsi 18
xen: --> irq=18
Already setup the GSI :18
megaraid_sas 0000:05:0e.0: PCI INT A -> GSI 18 (level, low) -> IRQ 18
megasas: FW now in Ready state
calling e1000_init_module+0x0/0(XEN) [VT-D]iommu.c:821:
iommu_fault_status: Primary Pending Fault
x70 [e1000e] @ 6(XEN) [VT-D]iommu.c:796: DMAR:[DMA Write] Request device
[05:08.0] fault addr 2d0842000, iommu reg = ffff82c3fff57000
(XEN) DMAR:[fault reason 02h] Present bit in context entry is clear
76
(XEN) print_vtd_entries: iommu = ffff83013ff7b130 bdf = 5:8.0 gmfn 2d0842
scsi6 : LSI SAS (XEN) root_entry = ffff83013ff37000
based MegaRAID d(XEN) root_entry[5] = 13cf13001
river
(XEN) context = ffff83013cf13000
initcall megasas(XEN) context[40] = 0_0
_init+0x0/0x16f (XEN) ctxt_entry[40] not present
[megaraid_sas] r(XEN) [VT-D]iommu.c:821: iommu_fault_status: Primary
Pending Fault
eturned 0 after (XEN) [VT-D]iommu.c:796: DMAR:[DMA Write] Request device
[05:08.0] fault addr 2d0842000, iommu reg = ffff82c3fff57000
(XEN) DMAR:[fault reason 02h] Present bit in context entry is clear
73201 usecs
(XEN) print_vtd_entries: iommu = ffff83013ff7b130 bdf = 5:8.0 gmfn 2d0842
scsi scan: INQUI(XEN) root_entry = ffff83013ff37000
RY result too sh(XEN) root_entry[5] = 13cf13001
ort (5), using 3(XEN) context = ffff83013cf13000
6
(XEN) context[40] = 0_0
scsi 6:0:0:0: Di(XEN) ctxt_entry[40] not present
rect-Access PQ: 0 ANSI: 0
scsi scan: INQUIRY result too short (5), using 36
scsi 6:0:1:0: Direct-Access PQ: 0
ANSI: 0
scsi scan: INQUIRY result too short (5), using 36
scsi 6:0:2:0: Direct-Access PQ: 0
ANSI: 0
scsi scan: INQUIRY result too short (5), using 36
scsi 6:0:3:0: Direct-Access PQ: 0
ANSI: 0
scsi 6:2:0:0: Direct-Access DELL PERC 5/i 1.03 PQ: 0
ANSI: 5
e1000e: Intel(R) PRO/1000 Network Driver - 1.0.2-k2
e1000e: Copyright (c) 1999-2008 Intel Corporation.
e1000e 0000:07:00.0: Disabling L1 ASPM
xen: registering gsi 16 triggering 0 polarity 1
xen_allocate_pirq: returning irq 16 for gsi 16
xen: --> irq=16
Already setup the GSI :16
e1000e 0000:07:00.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
e1000e 0000:07:00.0: setting latency timer to 64
alloc irq_desc for 4260 on node 0
alloc kstat_irqs on node 0
alloc irq_desc for 4259 on node 0
alloc kstat_irqs on node 0
alloc irq_desc for 4258 on node 0
sd 6:2:0:0: Attached scsi generic sg2 type 0
scsi_scan_6 used(XEN) [VT-D]iommu.c:821: iommu_fault_status: Primary
Pending Fault
greatest stack (XEN) [VT-D]iommu.c:796: DMAR:[DMA Write] Request device
[05:08.0] fault addr 2cfa6e000, iommu reg = ffff82c3fff57000
(XEN) DMAR:[fault reason 02h] Present bit in context entry is clear
depth: 4088 byte(XEN) print_vtd_entries: iommu = ffff83013ff7b130 bdf 5:8.0 gmfn
= 2cfa6e
s left
(XEN) root_entry = ffff83013ff37000
sd 6:2:0:0: [sdb(XEN) root_entry[5] = 13cf13001
] 211550208 512-(XEN) context = ffff83013cf13000
byte logical blo(XEN) context[40] = 0_0
cks: (108 GB/100(XEN) ctxt_entry[40] not present
GiB)
sd 6:2:0:0: [sdb] Write Protect is off
sd 6:2:0:0: [sdb] Mode Sense: 1f 00 00 08
sd 6:2:0:0: [sdb] Write cache: disabled, read cache: enabled, doesn''t
support DPO or FUA
sdb: unknown partition table
alloc kstat_irqs on node 0
sd 6:2:0:0: [sdb] Attached SCSI disk
0000:07:00.0: eth0: (PCI Express:2.5GB/s:Width x1) 00:30:48:b8:de:18
0000:07:00.0: eth0: Intel(R) PRO/1000 Network Connection
0000:07:00.0: eth0: MAC: 3, PHY: 8, PBA No: 0101ff-0ff
e1000e 0000:08:00.0: Disabling L1 ASPM
xen: registering gsi 17 triggering 0 polarity 1
xen_allocate_pirq: returning irq 17 for gsi 17
xen: --> irq=17
Already setup the GSI :17
e1000e 0000:08:00.0: PCI INT A -> GSI 17 (level, low) -> IRQ 17
e1000e 0000:08:00.0: setting latency timer to 64
alloc irq_desc for 4257 on node 0
alloc kstat_irqs on node 0
alloc irq_desc for 4256 on node 0
alloc kstat_irqs on node 0
alloc irq_desc for 4255 on node 0
alloc kstat_irqs on node 0
scsi_id used greatest stack depth: 3904 bytes left
0000:08:00.0: eth1: (PCI Express:2.5GB/s:Width x1) 00:30:48:b8:de:19
0000:08:00.0: eth1: Intel(R) PRO/1000 Network Connection
0000:08:00.0: eth1: MAC: 3, PHY: 8, PBA No: 0101ff-0ff
initcall e1000_init_module+0x0/0x70 [e1000e] returned 0 after 392599
usecs
(XEN) [VT-D]iommu.c:821: iommu_fault_status: Primary Pending Fault
(XEN) [VT-D]iommu.c:796: DMAR:[DMA Write] Request device [05:08.0] fault
addr 2cede1000, iommu reg = ffff82c3fff57000
(XEN) DMAR:[fault reason 02h] Present bit in context entry is clear
(XEN) print_vtd_entries: iommu = ffff83013ff7b130 bdf = 5:8.0 gmfn 2cede1
(XEN) root_entry = ffff83013ff37000
(XEN) root_entry[5] = 13cf13001
(XEN) context = ffff83013cf13000
(XEN) context[40] = 0_0
(XEN) ctxt_entry[40] not present
(XEN) [VT-D]iommu.c:821: iommu_fault_status: Primary Pending Fault
(XEN) [VT-D]iommu.c:796: DMAR:[DMA Write] Request device [05:08.0] fault
addr 2cede3000, iommu reg = ffff82c3fff57000
(XEN) DMAR:[fault reason 02h] Present bit in context entry is clear
(XEN) print_vtd_entries: iommu = ffff83013ff7b130 bdf = 5:8.0 gmfn 2cede3
(XEN) root_entry = ffff83013ff37000
(XEN) root_entry[5] = 13cf13001
(XEN) context = ffff83013cf13000
(XEN) context[40] = 0_0
(XEN) ctxt_entry[40] not present
(XEN) [VT-D]iommu.c:821: iommu_fault_status: Primary Pending Fault
(XEN) [VT-D]iommu.c:796: DMAR:[DMA Write] Request device [05:08.0] fault
addr 2cede2000, iommu reg = ffff82c3fff57000
(XEN) DMAR:[fault reason 02h] Present bit in context entry is clear
(XEN) print_vtd_entries: iommu = ffff83013ff7b130 bdf = 5:8.0 gmfn 2cede2
(XEN) root_entry = ffff83013ff37000
(XEN) root_entry[5] = 13cf13001
(XEN) context = ffff83013cf13000
(XEN) context[40] = 0_0
(XEN) ctxt_entry[40] not present
(XEN) [VT-D]iommu.c:821: iommu_fault_status: Primary Pending Fault
(XEN) [VT-D]iommu.c:796: DMAR:[DMA Write] Request device [05:08.0] fault
addr 2cfff9000, iommu reg = ffff82c3fff57000
(XEN) DMAR:[fault reason 02h] Present bit in context entry is clear
(XEN) print_vtd_entries: iommu = ffff83013ff7b130 bdf = 5:8.0 gmfn 2cfff9
(XEN) root_entry = ffff83013ff37000
(XEN) root_entry[5] = 13cf13001
(XEN) context = ffff83013cf13000
(XEN) context[40] = 0_0
(XEN) ctxt_entry[40] not present
(XEN) [VT-D]iommu.c:821: iommu_fault_status: Primary Pending Fault
(XEN) [VT-D]iommu.c:796: DMAR:[DMA Write] Request device [05:08.0] fault
addr 2ced30000, iommu reg = ffff82c3fff57000
(XEN) DMAR:[fault reason 02h] Present bit in context entry is clear
(XEN) print_vtd_entries: iommu = ffff83013ff7b130 bdf = 5:8.0 gmfn 2ced30
(XEN) root_entry = ffff83013ff37000
(XEN) root_entry[5] = 13cf13001
(XEN) context = ffff83013cf13000
(XEN) context[40] = 0_0
(XEN) ctxt_entry[40] not present
calling wait_scan_init+0x0/0x12 [scsi_wait_scan] @ 1132
initcall wait_scan_init+0x0/0x12 [scsi_wait_scan] returned 0 after 3
usecs
(XEN) [VT-D]iommu.c:821: iommu_fault_status: Primary Pending Fault
(XEN) [VT-D]iommu.c:796: DMAR:[DMA Write] Request device [05:08.0] fault
addr 2cf14b000, iommu reg = ffff82c3fff57000
(XEN) DMAR:[fault reason 02h] Present bit in context entry is clear
(XEN) print_vtd_entries: iommu = ffff83013ff7b130 bdf = 5:8.0 gmfn 2cf14b
(XEN) root_entry = ffff83013ff37000
(XEN) root_entry[5] = 13cf13001
(XEN) context = ffff83013cf13000
(XEN) context[40] = 0_0
(XEN) ctxt_entry[40] not present
On Sat, 2010-05-29 at 18:20 +0300, Pasi Kärkkäinen
wrote:> On Sat, May 29, 2010 at 07:31:17AM -0700, M. Nunberg wrote:
> > I''ve been trying to get VT-D working wiht xen for quite some
time, since
> > 3.4.2, and I''ve always had issues with my RAID controller not
working
> > properly when iommu is not disabled in Xen:
> >
> > lspci outpuut for the card:
>
> <snip>
>
> >
> > I am using a Supermicro X8DALi motherboard with a 5500 chipset.
> >
> > Whenever I try to access the device the Xen console spits out
something
> > like this:
> > (XEN) [VT-D]iommu.c:796: DMAR:[DMA Write] Request device [05:08.0]
fault
> > addr 204865000, iommu reg = ffff82c3fff57000
> > (XEN) DMAR:[fault reason 02h] Present bit in context entry is clear
> > (XEN) print_vtd_entries: iommu = ffff83013fffaee0 bdf = 5:8.0 gmfn
> > 204865
> > (XEN) root_entry = ffff83013ff37000
> > (XEN) root_entry[5] = 13cf12001
> > (XEN) context = ffff83013cf12000
> > (XEN) context[40] = 0_0
> > (XEN) ctxt_entry[40] not present
> > (XEN) [VT-D]iommu.c:821: iommu_fault_status: Primary Pending Fault
> >
> > reads are partially succcessful, but I am getting seek errors at
times,
> > filesystems will mount properly but I cannot use any of them
properly..
> >
> >
> > The actual kernel output varies, sometimes i get EINVAL when I try to
> > read from the filesystem, sometimes it simply refuses to at all
> > recognize the disk altogether, and other times it will hang the entire
> > system, including the hypervisor itself.
> > I''ve tried booting the hypervisor with x2apic disabled, but
to no
> > effect. I''ve also tried with the latest xen-4.0-testing
(4.0.1), buut
> > same issue and same outpuut
> >
> > A quick google turns up a thread, from this mailing list, with a
> > different RAID card, but the kernel output is similar.. e.g.
> >
> > scsi scan: INQUIRY result too short (5), using 36
> >
> >
http://lists.xensource.com/archives/html/xen-users/2010-04/msg00535.html
> >
> > The full xen log is below
> >
>
> Did you use the latest pvops dom0 kernel from xen/stable-2.6.32.x branch?
> Could you also post the full serial log _with_ the dom0 kernel messages?
>
> .. since the problem gets triggered by the dom0 kernel..
>
> -- Pasi
>
>
> >
> >
> > L __ __ _ _ ___
> > ___
> > \ \/ /___ _ __ | || | / _ \ / _ \ 0x146000>, shtab=0x3a2078,
> > entry=0x100000
> > \ // _ \ ''_ \ | || |_| | | | | |
> > |
> > / \ __/ | | | |__ _| |_| | |_| |apper/OS-root ro nomodeset
> > console=tty0 r
> > /_/\_\___|_| |_| |
> > _|(_)___(_)___/
> > 020
> > bytes]
> > (XEN) Xen version 4.0.0 (mordy@) (gcc version 4.3.2 (Debian 4.3.2-1.1)
)
> > Fri May 21 07:50:16 PDT 2010boot-module
> > @
> > (XEN) Latest ChangeSet:
> > unavailable
> > (XEN) Console output is
> > synchronous.
> > (XEN) Command line: iommu=verbose loglvl=all guest_loglvl=all
> > sync_console console_to_rint com1=115200,8n1
> > console=com1
> > (XEN) Video
> > information:
> > (XEN) VGA is text mode 80x25, font
> > 8x16
> > (XEN) VBE/DDC methods: none; EDID transfer time: 0
> > seconds
> > (XEN) EDID info not retrieved because no DDC retrieval method
> > detected
> > (XEN) Disc information:
> > (XEN) Found 1 MBR signatures
> > (XEN) Found 1 EDD information structures
> > (XEN) Xen-e820 RAM map:
> > (XEN) 0000000000000000 - 000000000009a000 (usable)
> > (XEN) 000000000009a000 - 00000000000a0000 (reserved)
> > (XEN) 00000000000e0000 - 0000000000100000 (reserved)
> > (XEN) 0000000000100000 - 00000000bf760000 (usable)
> > (XEN) 00000000bf76e000 - 00000000bf770000 type 9
> > (XEN) 00000000bf770000 - 00000000bf77e000 (ACPI data)
> > (XEN) 00000000bf77e000 - 00000000bf7d0000 (ACPI NVS)
> > (XEN) 00000000bf7d0000 - 00000000bf7e0000 (reserved)
> > (XEN) 00000000bf7ec000 - 00000000c0000000 (reserved)
> > (XEN) 00000000fee00000 - 00000000fee01000 (reserved)
> > (XEN) 00000000ffc00000 - 0000000100000000 (reserved)
> > (XEN) 0000000100000000 - 0000000340000000 (usable)
> > (XEN) ACPI: RSDP 000F9E10, 0024 (r2 ACPIAM)
> > (XEN) ACPI: XSDT BF770100, 0094 (r1 NEC 20090424 MSFT
> > 97)
> > (XEN) ACPI: FACP BF770290, 00F4 (r4 042409 FACP1917 20090424 MSFT
> > 97)
> > (XEN) ACPI: DSDT BF770670, 5BFB (r2 10601 10601000 0 INTL
> > 20051117)
> > (XEN) ACPI: FACS BF77E000, 0040
> > (XEN) ACPI: APIC BF770390, 00D2 (r2 042409 APIC1917 20090424 MSFT
> > 97)
> > (XEN) ACPI: MCFG BF770470, 003C (r1 042409 OEMMCFG 20090424 MSFT
> > 97)
> > (XEN) ACPI: SLIC BF7704B0, 0176 (r1 NEC 20090424 MSFT
> > 97)
> > (XEN) ACPI: ERST BF770630, 0040 (r1 042409 WHEA1917 20090424 MSFT
> > 97)
> > (XEN) ACPI: OEMB BF77E040, 007B (r1 042409 OEMB1917 20090424 MSFT
> > 97)
> > (XEN) ACPI: SRAT BF77A670, 01D0 (r1 042409 OEMSRAT 1 INTL
> > 1)
> > (XEN) ACPI: HPET BF77A840, 0038 (r1 042409 OEMHPET 20090424 MSFT
> > 97)
> > (XEN) ACPI: DMAR BF77E0C0, 0118 (r1 AMI OEMDMAR 1 MSFT
> > 97)
> > (XEN) ACPI: SSDT BF781DF0, 0363 (r1 DpgPmm CpuPm 12 INTL
> > 20051117)
> > (XEN) ACPI: EINJ BF77A880, 0130 (r1 AMIER AMI_EINJ 20090424 MSFT
> > 97)
> > (XEN) ACPI: BERT BF77AA10, 0030 (r1 AMIER AMI_BERT 20090424 MSFT
> > 97)
> > (XEN) ACPI: ERST BF77AA40, 01B0 (r1 AMIER AMI_ERST 20090424 MSFT
> > 97)
> > (XEN) ACPI: HEST BF77ABF0, 00A8 (r1 AMIER AMI_HEST 20090424 MSFT
> > 97)
> > (XEN) System RAM: 12045MB (12334808kB)
> > (XEN) SRAT: PXM 0 -> APIC 0 -> Node 0
> > (XEN) SRAT: PXM 0 -> APIC 2 -> Node 0
> > (XEN) SRAT: PXM 0 -> APIC 4 -> Node 0
> > (XEN) SRAT: PXM 0 -> APIC 6 -> Node 0
> > (XEN) SRAT: PXM 0 -> APIC 1 -> Node 0
> > (XEN) SRAT: PXM 0 -> APIC 3 -> Node 0
> > (XEN) SRAT: PXM 0 -> APIC 5 -> Node 0
> > (XEN) SRAT: PXM 0 -> APIC 7 -> Node 0
> > (XEN) SRAT: PXM 1 -> APIC 16 -> Node 1
> > (XEN) SRAT: PXM 1 -> APIC 18 -> Node 1
> > (XEN) SRAT: PXM 1 -> APIC 20 -> Node 1
> > (XEN) SRAT: PXM 1 -> APIC 22 -> Node 1
> > (XEN) SRAT: PXM 1 -> APIC 17 -> Node 1
> > (XEN) SRAT: PXM 1 -> APIC 19 -> Node 1
> > (XEN) SRAT: PXM 1 -> APIC 21 -> Node 1
> > (XEN) SRAT: PXM 1 -> APIC 23 -> Node 1
> > (XEN) SRAT: Node 0 PXM 0 0-a0000
> > (XEN) SRAT: Node 0 PXM 0 100000-c0000000
> > (XEN) SRAT: Node 0 PXM 0 100000000-1c0000000
> > (XEN) SRAT: Node 1 PXM 1 1c0000000-340000000
> > (XEN) NUMA: Allocated memnodemap from 33fdfb000 - 33fdff000
> > (XEN) NUMA: Using 8 for the hash shift.
> > (XEN) Domain heap initialised DMA width 30 bits
> > (XEN) found SMP MP-table at 000ff780
> > (XEN) DMI present.
> > (XEN) Using APIC driver default
> > (XEN) ACPI: PM-Timer IO Port: 0x808
> > (XEN) ACPI: ACPI SLEEP INFO: pm1x_cnt[804,0], pm1x_evt[800,0]
> > (XEN) ACPI: wakeup_vec[bf77e00c], vec_size[20]
> > (XEN) ACPI: Local APIC address 0xfee00000
> > (XEN) ACPI: LAPIC (acpi_id[0x01] lapic_id[0x00] enabled)
> > (XEN) Processor #0 7:10 APIC version 21
> > (XEN) ACPI: LAPIC (acpi_id[0x02] lapic_id[0x10] enabled)
> > (XEN) Processor #16 7:10 APIC version 21
> > (XEN) ACPI: LAPIC (acpi_id[0x03] lapic_id[0x02] enabled)
> > (XEN) Processor #2 7:10 APIC version 21
> > (XEN) ACPI: LAPIC (acpi_id[0x04] lapic_id[0x12] enabled)
> > (XEN) Processor #18 7:10 APIC version 21
> > (XEN) ACPI: LAPIC (acpi_id[0x05] lapic_id[0x04] enabled)
> > (XEN) Processor #4 7:10 APIC version 21
> > (XEN) ACPI: LAPIC (acpi_id[0x06] lapic_id[0x14] enabled)
> > (XEN) Processor #20 7:10 APIC version 21
> > (XEN) ACPI: LAPIC (acpi_id[0x07] lapic_id[0x06] enabled)
> > (XEN) Processor #6 7:10 APIC version 21
> > (XEN) ACPI: LAPIC (acpi_id[0x08] lapic_id[0x16] enabled)
> > (XEN) Processor #22 7:10 APIC version 21
> > (XEN) ACPI: LAPIC (acpi_id[0x09] lapic_id[0x01] enabled)
> > (XEN) Processor #1 7:10 APIC version 21
> > (XEN) ACPI: LAPIC (acpi_id[0x0a] lapic_id[0x11] enabled)
> > (XEN) Processor #17 7:10 APIC version 21
> > (XEN) ACPI: LAPIC (acpi_id[0x0b] lapic_id[0x03] enabled)
> > (XEN) Processor #3 7:10 APIC version 21
> > (XEN) ACPI: LAPIC (acpi_id[0x0c] lapic_id[0x13] enabled)
> > (XEN) Processor #19 7:10 APIC version 21
> > (XEN) ACPI: LAPIC (acpi_id[0x0d] lapic_id[0x05] enabled)
> > (XEN) Processor #5 7:10 APIC version 21
> > (XEN) ACPI: LAPIC (acpi_id[0x0e] lapic_id[0x15] enabled)
> > (XEN) Processor #21 7:10 APIC version 21
> > (XEN) ACPI: LAPIC (acpi_id[0x0f] lapic_id[0x07] enabled)
> > (XEN) Processor #7 7:10 APIC version 21
> > (XEN) ACPI: LAPIC (acpi_id[0x10] lapic_id[0x17] enabled)
> > (XEN) Processor #23 7:10 APIC version 21
> > (XEN) ACPI: LAPIC_NMI (acpi_id[0xff] dfl dfl lint[0x1])
> > (XEN) Overriding APIC driver with bigsmp
> > (XEN) ACPI: IOAPIC (id[0x08] address[0xfec00000] gsi_base[0])
> > (XEN) IOAPIC[0]: apic_id 8, version 32, address 0xfec00000, GSI 0-23
> > (XEN) ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
> > (XEN) ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 20 low level)
> > (XEN) ACPI: IRQ0 used by override.
> > (XEN) ACPI: IRQ2 used by override.
> > (XEN) ACPI: IRQ9 used by override.
> > (XEN) Enabling APIC mode: Phys. Using 1 I/O APICs
> > (XEN) ACPI: HPET id: 0xffffffff base: 0xfed00000
> > (XEN) [VT-D]dmar.c:679: Host address width 40
> > (XEN) [VT-D]dmar.c:694: found ACPI_DMAR_DRHD:
> > (XEN) [VT-D]dmar.c:398: dmaru->address = fbffe000
> > (XEN) [VT-D]dmar.c:340: IOAPIC: f0:1f.7
> > (XEN) [VT-D]dmar.c:411: flags: INCLUDE_ALL
> > (XEN) [VT-D]dmar.c:699: found ACPI_DMAR_RMRR:
> > (XEN) [VT-D]dmar.c:334: endpoint: 0:1d.0
> > (XEN) [VT-D]dmar.c:334: endpoint: 0:1d.1
> > (XEN) [VT-D]dmar.c:334: endpoint: 0:1d.2
> > (XEN) [VT-D]dmar.c:334: endpoint: 0:1d.7
> > (XEN) [VT-D]dmar.c:334: endpoint: 0:1a.0
> > (XEN) [VT-D]dmar.c:334: endpoint: 0:1a.1
> > (XEN) [VT-D]dmar.c:334: endpoint: 0:1a.2
> > (XEN) [VT-D]dmar.c:334: endpoint: 0:1a.7
> > (XEN) [VT-D]dmar.c:571: RMRR region: base_addr ec000 end_address
effff
> > (XEN) [VT-D]dmar.c:699: found ACPI_DMAR_RMRR:
> > (XEN) [VT-D]dmar.c:334: endpoint: 0:1d.0
> > (XEN) [VT-D]dmar.c:334: endpoint: 0:1d.1
> > (XEN) [VT-D]dmar.c:334: endpoint: 0:1d.2
> > (XEN) [VT-D]dmar.c:334: endpoint: 0:1d.7
> > (XEN) [VT-D]dmar.c:334: endpoint: 0:1a.0
> > (XEN) [VT-D]dmar.c:334: endpoint: 0:1a.1
> > (XEN) [VT-D]dmar.c:334: endpoint: 0:1a.2
> > (XEN) [VT-D]dmar.c:334: endpoint: 0:1a.7
> > (XEN) [VT-D]dmar.c:571: RMRR region: base_addr bf7ec000 end_address
> > bf7fffff
> > (XEN) [VT-D]dmar.c:704: found ACPI_DMAR_ATSR:
> > (XEN) [VT-D]dmar.c:599: atsru->all_ports: 0
> > (XEN) [VT-D]dmar.c:320: bridge: 0:1.0 start = 0 sec = 1 sub = 1
> > (XEN) [VT-D]dmar.c:320: bridge: 0:3.0 start = 0 sec = 2 sub = 2
> > (XEN) [VT-D]dmar.c:320: bridge: 0:7.0 start = 0 sec = 3 sub = 3
> > (XEN) PCI: MCFG configuration 0: base e0000000 segment 0 buses 0 - 255
> > (XEN) PCI: Not using MMCONFIG.
> > (XEN) Using ACPI (MADT) for SMP configuration information
> > (XEN) Using scheduler: SMP Credit Scheduler (credit)
> > (XEN) Detected 2266.790 MHz processor.
> > (XEN) Initing memory sharing.
> > (XEN) VMX: Supported advanced features:
> > (XEN) - APIC MMIO access virtualisation
> > (XEN) - APIC TPR shadow
> > (XEN) - Extended Page Tables (EPT)
> > (XEN) - Virtual-Processor Identifiers (VPID)
> > (XEN) - Virtual NMI
> > (XEN) - MSR direct-access bitmap
> > (XEN) HVM: ASIDs enabled.
> > (XEN) HVM: VMX enabled
> > (XEN) HVM: Hardware Assisted Paging detected.
> > (XEN) Intel machine check reporting enabled
> > (XEN) [VT-D]iommu.c:1078: drhd->address = fbffe000 iommu->reg
> > ffff82c3fff57000
> > (XEN) [VT-D]iommu.c:1080: cap = c90780106f0462 ecap = f0207e
> > (XEN) Intel VT-d Snoop Control not supported.
> > (XEN) Intel VT-d DMA Passthrough not supported.
> > (XEN) Intel VT-d Queued Invalidation supported.
> > (XEN) Intel VT-d Interrupt Remapping supported.
> > (XEN) I/O virtualisation enabled
> > (XEN) I/O virtualisation for PV guests disabled
> > (XEN) Total of 16 processors activated.
> > (XEN) ENABLING IO-APIC IRQs
> > (XEN) -> Using new ACK method
> > (XEN) ..TIMER: vector=0xF0 apic1=0 pin1=2 apic2=-1 pin2=-1
> > (XEN) TSC is reliable, synchronization unnecessary
> > (XEN) Platform timer is 14.318MHz HPET
> > ?(XEN) Allocated console ring of 128 KiB.
> > (XEN) microcode.c:73:d32767 microcode: CPU1 resumed
> > (XEN) microcode.c:73:d32767 microcode: CPU9 resumed
> > (XEN) microcode.c:73:d32767 microcode: CPU14 resumed
> > (XEN) microcode.c:73:d32767 microcode: CPU6 resumed
> > (XEN) microcode.c:73:d32767 microcode: CPU3 resumed
> > (XEN) microcode.c:73:d32767 microcode: CPU11 resumed
> > (XEN) microcode.c:73:d32767 microcode: CPU8 resumed
> > (XEN) microcode.c:73:d32767 microcode: CPU7 resumed
> > (XEN) microcode.c:73:d32767 microcode: CPU15 resumed
> > (XEN) microcode.c:73:d32767 microcode: CPU2 resumed
> > (XEN) microcode.c:73:d32767 microcode: CPU5 resumed
> > (XEN) microcode.c:73:d32767 microcode: CPU13 resumed
> > (XEN) microcode.c:73:d32767 microcode: CPU4 resumed
> > (XEN) microcode.c:73:d32767 microcode: CPU10 resumed
> > (XEN) Brought up 16 CPUs
> > (XEN) microcode.c:73:d32767 microcode: CPU12 resumed
> > (XEN) Turbo Mode detected!
> > (XEN) HPET''s MSI mode hasn''t been supported when
Interrupt Remapping is
> > enabled.
> > (XEN) ACPI sleep modes: S3
> > (XEN) mcheck_poll: Machine check polling timer started.
> > (XEN) [VT-D]iommu.c:1325: d0:PCIe: map bdf = 0:0.0
> > (XEN) [VT-D]iommu.c:1325: d0:PCIe: map bdf = 0:14.0
> > (XEN) [VT-D]iommu.c:1325: d0:PCIe: map bdf = 0:14.1
> > (XEN) [VT-D]iommu.c:1325: d0:PCIe: map bdf = 0:14.2
> > (XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = 0:14.3
> > (XEN) [VT-D]iommu.c:1325: d0:PCIe: map bdf = 0:16.0
> > (XEN) [VT-D]iommu.c:1325: d0:PCIe: map bdf = 0:16.1
> > (XEN) [VT-D]iommu.c:1325: d0:PCIe: map bdf = 0:16.2
> > (XEN) [VT-D]iommu.c:1325: d0:PCIe: map bdf = 0:16.3
> > (XEN) [VT-D]iommu.c:1325: d0:PCIe: map bdf = 0:16.4
> > (XEN) [VT-D]iommu.c:1325: d0:PCIe: map bdf = 0:16.5
> > (XEN) [VT-D]iommu.c:1325: d0:PCIe: map bdf = 0:16.6
> > (XEN) [VT-D]iommu.c:1325: d0:PCIe: map bdf = 0:16.7
> > (XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = 0:1a.0
> > (XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = 0:1a.1
> > (XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = 0:1a.2
> > (XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = 0:1a.7
> > (XEN) [VT-D]iommu.c:1325: d0:PCIe: map bdf = 0:1b.0
> > (XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = 0:1d.0
> > (XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = 0:1d.1
> > (XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = 0:1d.2
> > (XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = 0:1d.7
> > (XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = 0:1f.0
> > (XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = 0:1f.2
> > (XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = 0:1f.3
> > (XEN) [VT-D]iommu.c:1325: d0:PCIe: map bdf = 1:0.0
> > (XEN) [VT-D]iommu.c:1325: d0:PCIe: map bdf = 3:0.0
> > (XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = 5:e.0
> > (XEN) [VT-D]iommu.c:1325: d0:PCIe: map bdf = 7:0.0
> > (XEN) [VT-D]iommu.c:1325: d0:PCIe: map bdf = 8:0.0
> > (XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = fe:0.0
> > (XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = fe:0.1
> > (XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = fe:2.0
> > (XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = fe:2.1
> > (XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = fe:2.4
> > (XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = fe:2.5
> > (XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = fe:3.0
> > (XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = fe:3.1
> > (XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = fe:3.2
> > (XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = fe:3.4
> > (XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = fe:4.0
> > (XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = fe:4.1
> > (XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = fe:4.2
> > (XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = fe:4.3
> > (XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = fe:5.0
> > (XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = fe:5.1
> > (XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = fe:5.2
> > (XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = fe:5.3
> > (XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = fe:6.0
> > (XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = fe:6.1
> > (XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = fe:6.2
> > (XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = fe:6.3
> > (XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = ff:0.0
> > (XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = ff:0.1
> > (XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = ff:2.0
> > (XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = ff:2.1
> > (XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = ff:2.4
> > (XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = ff:2.5
> > (XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = ff:3.0
> > (XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = ff:3.1
> > (XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = ff:3.2
> > (XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = ff:3.4
> > (XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = ff:4.0
> > (XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = ff:4.1
> > (XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = ff:4.2
> > (XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = ff:4.3
> > (XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = ff:5.0
> > (XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = ff:5.1
> > (XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = ff:5.2
> > (XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = ff:5.3
> > (XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = ff:6.0
> > (XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = ff:6.1
> > (XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = ff:6.2
> > (XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = ff:6.3
> > (XEN) [VT-D]iommu.c:695: iommu_enable_translation: iommu->reg >
> ffff82c3fff57000
> > (XEN) *** LOADING DOMAIN 0 ***
> > (XEN) Xen kernel: 64-bit, lsb, compat32
> > (XEN) Dom0 kernel: 64-bit, PAE, lsb, paddr 0x1000000 -> 0x26b6000
> > (XEN) PHYSICAL MEMORY ARRANGEMENT:
> > (XEN) Dom0 alloc.: 0000000100000000->0000000120000000 (2937045
pages
> > to be allocated)
> > (XEN) VIRTUAL MEMORY ARRANGEMENT:
> > (XEN) Loaded kernel: ffffffff81000000->ffffffff826b6000
> > (XEN) Init. ramdisk: ffffffff826b6000->ffffffff8f7d7600
> > (XEN) Phys-Mach map: ffffffff8f7d8000->ffffffff90f406a8
> > (XEN) Start info: ffffffff90f41000->ffffffff90f414b4
> > (XEN) Page tables: ffffffff90f42000->ffffffff90fcf000
> > (XEN) Boot stack: ffffffff90fcf000->ffffffff90fd0000
> > (XEN) TOTAL: ffffffff80000000->ffffffff91400000
> > (XEN) ENTRY ADDRESS: ffffffff819be200
> > (XEN) Dom0 has maximum 16 VCPUs
> > (XEN) Scrubbing Free RAM: .done.
> > (XEN) Xen trace buffers: disabled
> > (XEN) Std. Loglevel: All
> > (XEN) Guest Loglevel: All
> > (XEN) **********************************************
> > (XEN) ******* WARNING: CONSOLE OUTPUT IS SYNCHRONOUS
> > (XEN) ******* This option is intended to aid debugging of Xen by
> > ensuring
> > (XEN) ******* that all output is synchronously delivered on the serial
> > line.
> > (XEN) ******* However it can introduce SIGNIFICANT latencies and
affect
> > (XEN) ******* timekeeping. It is NOT recommended for production use!
> > (XEN) **********************************************
> > (XEN) 3... 2... 1...
> > (XEN) *** Serial input -> DOM0 (type ''CTRL-a''
three times to switch
> > input to Xen)
> > (XEN) Freed 164kB init memory.
> > mapping kernel into physical memory
> > Xen: setup ISA identity maps
> > about to get started...
> > (XEN) PCI add device 00:00.0
> > (XEN) PCI add device 00:01.0
> > (XEN) PCI add device 00:03.0
> > (XEN) PCI add device 00:07.0
> > (XEN) PCI add device 00:14.0
> > (XEN) PCI add device 00:14.1
> > (XEN) PCI add device 00:14.2
> > (XEN) PCI add device 00:14.3
> > (XEN) PCI add device 00:16.0
> > (XEN) PCI add device 00:16.1
> > (XEN) PCI add device 00:16.2
> > (XEN) PCI add device 00:16.3
> > (XEN) PCI add device 00:16.4
> > (XEN) PCI add device 00:16.5
> > (XEN) PCI add device 00:16.6
> > (XEN) PCI add device 00:16.7
> > (XEN) PCI add device 00:1a.0
> > (XEN) PCI add device 00:1a.1
> > (XEN) PCI add device 00:1a.2
> > (XEN) PCI add device 00:1a.7
> > (XEN) PCI add device 00:1b.0
> > (XEN) PCI add device 00:1c.0
> > (XEN) PCI add device 00:1c.4
> > (XEN) PCI add device 00:1c.5
> > (XEN) PCI add device 00:1d.0
> > (XEN) PCI add device 00:1d.1
> > (XEN) PCI add device 00:1d.2
> > (XEN) PCI add device 00:1d.7
> > (XEN) PCI add device 00:1e.0
> > (XEN) PCI add device 00:1f.0
> > (XEN) PCI add device 00:1f.2
> > (XEN) PCI add device 00:1f.3
> > (XEN) PCI add device 01:00.0
> > (XEN) PCI add device 03:00.0
> > (XEN) PCI add device 04:00.0
> > (XEN) PCI add device 04:00.2
> > (XEN) PCI add device 05:0e.0
> > (XEN) PCI add device 07:00.0
> > (XEN) PCI add device 08:00.0
> > (XEN) cpuid.MWAIT[.eax=40, .ebx=40, .ecx=3, .edx=1120]
> > (XEN) Monitor-Mwait will be used to enter C-1 state
> > (XEN) cpuid.MWAIT[.eax=40, .ebx=40, .ecx=3, .edx=1120]
> > (XEN) Monitor-Mwait will be used to enter C-3 state
> > (XEN) cpuid.MWAIT[.eax=40, .ebx=40, .ecx=3, .edx=1120]
> > (XEN) Monitor-Mwait will be used to enter C-3 state
> > (XEN) cpuid.MWAIT[.eax=40, .ebx=40, .ecx=3, .edx=1120]
> > (XEN) Monitor-Mwait will be used to enter C-1 state
> > (XEN) cpuid.MWAIT[.eax=40, .ebx=40, .ecx=3, .edx=1120]
> > (XEN) Monitor-Mwait will be used to enter C-3 state
> > (XEN) cpuid.MWAIT[.eax=40, .ebx=40, .ecx=3, .edx=1120]
> > (XEN) Monitor-Mwait will be used to enter C-3 state
> > (XEN) cpuid.MWAIT[.eax=40, .ebx=40, .ecx=3, .edx=1120]
> > (XEN) Monitor-Mwait will be used to enter C-1 state
> > (XEN) cpuid.MWAIT[.eax=40, .ebx=40, .ecx=3, .edx=1120]
> > (XEN) Monitor-Mwait will be used to enter C-3 state
> > (XEN) cpuid.MWAIT[.eax=40, .ebx=40, .ecx=3, .edx=1120]
> > (XEN) Monitor-Mwait will be used to enter C-3 state
> > (XEN) cpuid.MWAIT[.eax=40, .ebx=40, .ecx=3, .edx=1120]
> > (XEN) Monitor-Mwait will be used to enter C-1 state
> > (XEN) cpuid.MWAIT[.eax=40, .ebx=40, .ecx=3, .edx=1120]
> > (XEN) Monitor-Mwait will be used to enter C-3 state
> > (XEN) cpuid.MWAIT[.eax=40, .ebx=40, .ecx=3, .edx=1120]
> > (XEN) Monitor-Mwait will be used to enter C-3 state
> > (XEN) cpuid.MWAIT[.eax=40, .ebx=40, .ecx=3, .edx=1120]
> > (XEN) Monitor-Mwait will be used to enter C-1 state
> > (XEN) cpuid.MWAIT[.eax=40, .ebx=40, .ecx=3, .edx=1120]
> > (XEN) Monitor-Mwait will be used to enter C-3 state
> > (XEN) cpuid.MWAIT[.eax=40, .ebx=40, .ecx=3, .edx=1120]
> > (XEN) Monitor-Mwait will be used to enter C-3 state
> > (XEN) cpuid.MWAIT[.eax=40, .ebx=40, .ecx=3, .edx=1120]
> > (XEN) Monitor-Mwait will be used to enter C-1 state
> > (XEN) cpuid.MWAIT[.eax=40, .ebx=40, .ecx=3, .edx=1120]
> > (XEN) Monitor-Mwait will be used to enter C-3 state
> > (XEN) cpuid.MWAIT[.eax=40, .ebx=40, .ecx=3, .edx=1120]
> > (XEN) Monitor-Mwait will be used to enter C-3 state
> > (XEN) cpuid.MWAIT[.eax=40, .ebx=40, .ecx=3, .edx=1120]
> > (XEN) Monitor-Mwait will be used to enter C-1 state
> > (XEN) cpuid.MWAIT[.eax=40, .ebx=40, .ecx=3, .edx=1120]
> > (XEN) Monitor-Mwait will be used to enter C-3 state
> > (XEN) cpuid.MWAIT[.eax=40, .ebx=40, .ecx=3, .edx=1120]
> > (XEN) Monitor-Mwait will be used to enter C-3 state
> > (XEN) cpuid.MWAIT[.eax=40, .ebx=40, .ecx=3, .edx=1120]
> > (XEN) Monitor-Mwait will be used to enter C-1 state
> > (XEN) cpuid.MWAIT[.eax=40, .ebx=40, .ecx=3, .edx=1120]
> > (XEN) Monitor-Mwait will be used to enter C-3 state
> > (XEN) cpuid.MWAIT[.eax=40, .ebx=40, .ecx=3, .edx=1120]
> > (XEN) Monitor-Mwait will be used to enter C-3 state
> > (XEN) cpuid.MWAIT[.eax=40, .ebx=40, .ecx=3, .edx=1120]
> > (XEN) Monitor-Mwait will be used to enter C-1 state
> > (XEN) cpuid.MWAIT[.eax=40, .ebx=40, .ecx=3, .edx=1120]
> > (XEN) Monitor-Mwait will be used to enter C-3 state
> > (XEN) cpuid.MWAIT[.eax=40, .ebx=40, .ecx=3, .edx=1120]
> > (XEN) Monitor-Mwait will be used to enter C-3 state
> > (XEN) cpuid.MWAIT[.eax=40, .ebx=40, .ecx=3, .edx=1120]
> > (XEN) Monitor-Mwait will be used to enter C-1 state
> > (XEN) cpuid.MWAIT[.eax=40, .ebx=40, .ecx=3, .edx=1120]
> > (XEN) Monitor-Mwait will be used to enter C-3 state
> > (XEN) cpuid.MWAIT[.eax=40, .ebx=40, .ecx=3, .edx=1120]
> > (XEN) Monitor-Mwait will be used to enter C-3 state
> > (XEN) cpuid.MWAIT[.eax=40, .ebx=40, .ecx=3, .edx=1120]
> > (XEN) Monitor-Mwait will be used to enter C-1 state
> > (XEN) cpuid.MWAIT[.eax=40, .ebx=40, .ecx=3, .edx=1120]
> > (XEN) Monitor-Mwait will be used to enter C-3 state
> > (XEN) cpuid.MWAIT[.eax=40, .ebx=40, .ecx=3, .edx=1120]
> > (XEN) Monitor-Mwait will be used to enter C-3 state
> > (XEN) cpuid.MWAIT[.eax=40, .ebx=40, .ecx=3, .edx=1120]
> > (XEN) Monitor-Mwait will be used to enter C-1 state
> > (XEN) cpuid.MWAIT[.eax=40, .ebx=40, .ecx=3, .edx=1120]
> > (XEN) Monitor-Mwait will be used to enter C-3 state
> > (XEN) cpuid.MWAIT[.eax=40, .ebx=40, .ecx=3, .edx=1120]
> > (XEN) Monitor-Mwait will be used to enter C-3 state
> > (XEN) cpuid.MWAIT[.eax=40, .ebx=40, .ecx=3, .edx=1120]
> > (XEN) Monitor-Mwait will be used to enter C-1 state
> > (XEN) cpuid.MWAIT[.eax=40, .ebx=40, .ecx=3, .edx=1120]
> > (XEN) Monitor-Mwait will be used to enter C-3 state
> > (XEN) cpuid.MWAIT[.eax=40, .ebx=40, .ecx=3, .edx=1120]
> > (XEN) Monitor-Mwait will be used to enter C-3 state
> > (XEN) cpuid.MWAIT[.eax=40, .ebx=40, .ecx=3, .edx=1120]
> > (XEN) Monitor-Mwait will be used to enter C-1 state
> > (XEN) cpuid.MWAIT[.eax=40, .ebx=40, .ecx=3, .edx=1120]
> > (XEN) Monitor-Mwait will be used to enter C-3 state
> > (XEN) cpuid.MWAIT[.eax=40, .ebx=40, .ecx=3, .edx=1120]
> > (XEN) Monitor-Mwait will be used to enter C-3 state
> > (XEN) cpuid.MWAIT[.eax=40, .ebx=40, .ecx=3, .edx=1120]
> > (XEN) Monitor-Mwait will be used to enter C-1 state
> > (XEN) cpuid.MWAIT[.eax=40, .ebx=40, .ecx=3, .edx=1120]
> > (XEN) Monitor-Mwait will be used to enter C-3 state
> > (XEN) cpuid.MWAIT[.eax=40, .ebx=40, .ecx=3, .edx=1120]
> > (XEN) Monitor-Mwait will be used to enter C-3 state
> > (XEN) cpuid.MWAIT[.eax=40, .ebx=40, .ecx=3, .edx=1120]
> > (XEN) Monitor-Mwait will be used to enter C-1 state
> > (XEN) cpuid.MWAIT[.eax=40, .ebx=40, .ecx=3, .edx=1120]
> > (XEN) Monitor-Mwait will be used to enter C-3 state
> > (XEN) cpuid.MWAIT[.eax=40, .ebx=40, .ecx=3, .edx=1120]
> > (XEN) Monitor-Mwait will be used to enter C-3 state
> > (XEN) irq.c:1139:d0 Cannot bind IRQ 4 to guest. In use by
''ns16550''.
> > (XEN) irq.c:1139:d0 Cannot bind IRQ 2 to guest. In use by
''cascade''.
> > (XEN) irq.c:1139:d0 Cannot bind IRQ 4 to guest. In use by
''ns16550''.
> > (XEN) irq.c:1139:d0 Cannot bind IRQ 2 to guest. In use by
''cascade''.
> > (XEN) irq.c:1139:d0 Cannot bind IRQ 4 to guest. In use by
''ns16550''.
> > (XEN) irq.c:1139:d0 Cannot bind IRQ 2 to guest. In use by
''cascade''.
> > (XEN) irq.c:1139:d0 Cannot bind IRQ 4 to guest. In use by
''ns16550''.
> > (XEN) irq.c:1139:d0 Cannot bind IRQ 2 to guest. In use by
''cascade''.
> > (XEN) [VT-D]iommu.c:821: iommu_fault_status: Primary Pending Fault
> > (XEN) [VT-D]iommu.c:796: DMAR:[DMA Write] Request device [05:08.0]
fault
> > addr 203a09000, iommu reg = ffff82c3fff57000
> > (XEN) DMAR:[fault reason 02h] Present bit in context entry is clear
> > (XEN) print_vtd_entries: iommu = ffff83013fffaee0 bdf = 5:8.0 gmfn
> > 203a09
> > (XEN) root_entry = ffff83013ff37000
> > (XEN) root_entry[5] = 13cf12001
> > (XEN) context = ffff83013cf12000
> > (XEN) context[40] = 0_0
> > (XEN) ctxt_entry[40] not present
> > (XEN) [VT-D]iommu.c:796: DMAR:[DMA Write] Request device [05:08.0]
fault
> > addr 203eba000, iommu reg = ffff82c3fff57000
> > (XEN) DMAR:[fault reason 02h] Present bit in context entry is clear
> > (XEN) print_vtd_entries: iommu = ffff83013fffaee0 bdf = 5:8.0 gmfn
> > 203eba
> > (XEN) root_entry = ffff83013ff37000
> > (XEN) root_entry[5] = 13cf12001
> > (XEN) context = ffff83013cf12000
> > (XEN) context[40] = 0_0
> > (XEN) ctxt_entry[40] not present
> > (XEN) [VT-D]iommu.c:821: iommu_fault_status: Primary Pending Fault
> > (XEN) [VT-D]iommu.c:796: DMAR:[DMA Write] Request device [05:08.0]
fault
> > addr 204e11000, iommu reg = ffff82c3fff57000
> > (XEN) DMAR:[fault reason 02h] Present bit in context entry is clear
> > (XEN) print_vtd_entries: iommu = ffff83013fffaee0 bdf = 5:8.0 gmfn
> > 204e11
> > (XEN) root_entry = ffff83013ff37000
> > (XEN) root_entry[5] = 13cf12001
> > (XEN) context = ffff83013cf12000
> > (XEN) context[40] = 0_0
> > (XEN) ctxt_entry[40] not present
> > (XEN) [VT-D]iommu.c:821: iommu_fault_status: Primary Pending Fault
> > (XEN) [VT-D]iommu.c:796: DMAR:[DMA Write] Request device [05:08.0]
fault
> > addr 2061e2000, iommu reg = ffff82c3fff57000
> > (XEN) DMAR:[fault reason 02h] Present bit in context entry is clear
> > (XEN) print_vtd_entries: iommu = ffff83013fffaee0 bdf = 5:8.0 gmfn
> > 2061e2
> > (XEN) root_entry = ffff83013ff37000
> > (XEN) root_entry[5] = 13cf12001
> > (XEN) context = ffff83013cf12000
> > (XEN) context[40] = 0_0
> > (XEN) ctxt_entry[40] not present
> > (XEN) [VT-D]iommu.c:796: DMAR:[DMA Write] Request device [05:08.0]
fault
> > addr 205043000, iommu reg = ffff82c3fff57000
> > (XEN) DMAR:[fault reason 02h] Present bit in context entry is clear
> > (XEN) print_vtd_entries: iommu = ffff83013fffaee0 bdf = 5:8.0 gmfn
> > 205043
> > (XEN) root_entry = ffff83013ff37000
> > (XEN) root_entry[5] = 13cf12001
> > (XEN) context = ffff83013cf12000
> > (XEN) context[40] = 0_0
> > (XEN) ctxt_entry[40] not present
> > (XEN) [VT-D]iommu.c:821: iommu_fault_status: Primary Pending Fault
> > (XEN) [VT-D]iommu.c:796: DMAR:[DMA Write] Request device [05:08.0]
fault
> > addr 20552b000, iommu reg = ffff82c3fff57000
> > (XEN) DMAR:[fault reason 02h] Present bit in context entry is clear
> > (XEN) print_vtd_entries: iommu = ffff83013fffaee0 bdf = 5:8.0 gmfn
> > 20552b
> > (XEN) root_entry = ffff83013ff37000
> > (XEN) root_entry[5] = 13cf12001
> > (XEN) context = ffff83013cf12000
> > (XEN) context[40] = 0_0
> > (XEN) ctxt_entry[40] not present
> > (XEN) [VT-D]iommu.c:821: iommu_fault_status: Primary Pending Fault
> > (XEN) [VT-D]iommu.c:796: DMAR:[DMA Write] Request device [05:08.0]
fault
> > addr 205708000, iommu reg = ffff82c3fff57000
> > (XEN) DMAR:[fault reason 02h] Present bit in context entry is clear
> > (XEN) print_vtd_entries: iommu = ffff83013fffaee0 bdf = 5:8.0 gmfn
> > 205708
> > (XEN) root_entry = ffff83013ff37000
> > (XEN) root_entry[5] = 13cf12001
> > (XEN) context = ffff83013cf12000
> > (XEN) context[40] = 0_0
> > (XEN) ctxt_entry[40] not present
> > (XEN) [VT-D]iommu.c:796: DMAR:[DMA Write] Request device [05:08.0]
fault
> > addr 2060c0000, iommu reg = ffff82c3fff57000
> > (XEN) DMAR:[fault reason 02h] Present bit in context entry is clear
> > (XEN) print_vtd_entries: iommu = ffff83013fffaee0 bdf = 5:8.0 gmfn
> > 2060c0
> > (XEN) root_entry = ffff83013ff37000
> > (XEN) root_entry[5] = 13cf12001
> > (XEN) context = ffff83013cf12000
> > (XEN) context[40] = 0_0
> > (XEN) ctxt_entry[40] not present
> > (XEN) [VT-D]iommu.c:821: iommu_fault_status: Primary Pending Fault
> > (XEN) [VT-D]iommu.c:796: DMAR:[DMA Write] Request device [05:08.0]
fault
> > addr 206591000, iommu reg = ffff82c3fff57000
> > (XEN) DMAR:[fault reason 02h] Present bit in context entry is clear
> > (XEN) print_vtd_entries: iommu = ffff83013fffaee0 bdf = 5:8.0 gmfn
> > 206591
> > (XEN) root_entry = ffff83013ff37000
> > (XEN) root_entry[5] = 13cf12001
> > (XEN) context = ffff83013cf12000
> > (XEN) context[40] = 0_0
> > (XEN) ctxt_entry[40] not present
> > (XEN) [VT-D]iommu.c:796: DMAR:[DMA Write] Request device [05:08.0]
fault
> > addr 204353000, iommu reg = ffff82c3fff57000
> > (XEN) DMAR:[fault reason 02h] Present bit in context entry is clear
> > (XEN) print_vtd_entries: iommu = ffff83013fffaee0 bdf = 5:8.0 gmfn
> > 204353
> > (XEN) root_entry = ffff83013ff37000
> > (XEN) root_entry[5] = 13cf12001
> > (XEN) context = ffff83013cf12000
> > (XEN) context[40] = 0_0
> > (XEN) ctxt_entry[40] not present
> > (XEN) [VT-D]iommu.c:821: iommu_fault_status: Primary Pending Fault
> > (XEN) [VT-D]iommu.c:796: DMAR:[DMA Write] Request device [05:08.0]
fault
> > addr 2061f2000, iommu reg = ffff82c3fff57000
> > (XEN) DMAR:[fault reason 02h] Present bit in context entry is clear
> > (XEN) print_vtd_entries: iommu = ffff83013fffaee0 bdf = 5:8.0 gmfn
> > 2061f2
> > (XEN) root_entry = ffff83013ff37000
> > (XEN) root_entry[5] = 13cf12001
> > (XEN) context = ffff83013cf12000
> > (XEN) context[40] = 0_0
> > (XEN) ctxt_entry[40] not present
> > (XEN) [VT-D]iommu.c:796: DMAR:[DMA Write] Request device [05:08.0]
fault
> > addr 204306000, iommu reg = ffff82c3fff57000
> > (XEN) DMAR:[fault reason 02h] Present bit in context entry is clear
> > (XEN) print_vtd_entries: iommu = ffff83013fffaee0 bdf = 5:8.0 gmfn
> > 204306
> > (XEN) root_entry = ffff83013ff37000
> > (XEN) root_entry[5] = 13cf12001
> > (XEN) context = ffff83013cf12000
> > (XEN) context[40] = 0_0
> > (XEN) ctxt_entry[40] not present
> > (XEN) [VT-D]iommu.c:821: iommu_fault_status: Primary Pending Fault
> > (XEN) [VT-D]iommu.c:796: DMAR:[DMA Write] Request device [05:08.0]
fault
> > addr 205f6b000, iommu reg = ffff82c3fff57000
> > (XEN) DMAR:[fault reason 02h] Present bit in context entry is clear
> > (XEN) print_vtd_entries: iommu = ffff83013fffaee0 bdf = 5:8.0 gmfn
> > 205f6b
> > (XEN) root_entry = ffff83013ff37000
> > (XEN) root_entry[5] = 13cf12001
> > (XEN) context = ffff83013cf12000
> > (XEN) context[40] = 0_0
> > (XEN) ctxt_entry[40] not present
> > (XEN) [VT-D]iommu.c:796: DMAR:[DMA Write] Request device [05:08.0]
fault
> > addr 205665000, iommu reg = ffff82c3fff57000
> > (XEN) DMAR:[fault reason 02h] Present bit in context entry is clear
> > (XEN) print_vtd_entries: iommu = ffff83013fffaee0 bdf = 5:8.0 gmfn
> > 205665
> > (XEN) root_entry = ffff83013ff37000
> > (XEN) root_entry[5] = 13cf12001
> > (XEN) context = ffff83013cf12000
> > (XEN) context[40] = 0_0
> > (XEN) ctxt_entry[40] not present
> > (XEN) [VT-D]iommu.c:821: iommu_fault_status: Primary Pending Fault
> > (XEN) [VT-D]iommu.c:796: DMAR:[DMA Write] Request device [05:08.0]
fault
> > addr 2045a0000, iommu reg = ffff82c3fff57000
> > (XEN) DMAR:[fault reason 02h] Present bit in context entry is clear
> > (XEN) print_vtd_entries: iommu = ffff83013fffaee0 bdf = 5:8.0 gmfn
> > 2045a0
> > (XEN) root_entry = ffff83013ff37000
> > (XEN) root_entry[5] = 13cf12001
> > (XEN) context = ffff83013cf12000
> > (XEN) context[40] = 0_0
> > (XEN) ctxt_entry[40] not present
> > (XEN) [VT-D]iommu.c:796: DMAR:[DMA Write] Request device [05:08.0]
fault
> > addr 205669000, iommu reg = ffff82c3fff57000
> > (XEN) DMAR:[fault reason 02h] Present bit in context entry is clear
> > (XEN) print_vtd_entries: iommu = ffff83013fffaee0 bdf = 5:8.0 gmfn
> > 205669
> > (XEN) root_entry = ffff83013ff37000
> > (XEN) root_entry[5] = 13cf12001
> > (XEN) context = ffff83013cf12000
> > (XEN) context[40] = 0_0
> > (XEN) ctxt_entry[40] not present
> > (XEN) [VT-D]iommu.c:821: iommu_fault_status: Primary Pending Fault
> > (XEN) [VT-D]iommu.c:796: DMAR:[DMA Write] Request device [05:08.0]
fault
> > addr 2042c6000, iommu reg = ffff82c3fff57000
> > (XEN) DMAR:[fault reason 02h] Present bit in context entry is clear
> > (XEN) print_vtd_entries: iommu = ffff83013fffaee0 bdf = 5:8.0 gmfn
> > 2042c6
> > (XEN) root_entry = ffff83013ff37000
> > (XEN) root_entry[5] = 13cf12001
> > (XEN) context = ffff83013cf12000
> > (XEN) context[40] = 0_0
> > (XEN) ctxt_entry[40] not present
> > (XEN) [VT-D]iommu.c:796: DMAR:[DMA Write] Request device [05:08.0]
fault
> > addr 2061fe000, iommu reg = ffff82c3fff57000
> > (XEN) DMAR:[fault reason 02h] Present bit in context entry is clear
> > (XEN) print_vtd_entries: iommu = ffff83013fffaee0 bdf = 5:8.0 gmfn
> > 2061fe
> > (XEN) root_entry = ffff83013ff37000
> > (XEN) root_entry[5] = 13cf12001
> > (XEN) context = ffff83013cf12000
> > (XEN) context[40] = 0_0
> > (XEN) ctxt_entry[40] not present
> > (XEN) [VT-D]iommu.c:821: iommu_fault_status: Primary Pending Fault
> > (XEN) [VT-D]iommu.c:796: DMAR:[DMA Write] Request device [05:08.0]
fault
> > addr 20560a000, iommu reg = ffff82c3fff57000
> > (XEN) DMAR:[fault reason 02h] Present bit in context entry is clear
> > (XEN) print_vtd_entries: iommu = ffff83013fffaee0 bdf = 5:8.0 gmfn
> > 20560a
> > (XEN) root_entry = ffff83013ff37000
> > (XEN) root_entry[5] = 13cf12001
> > (XEN) context = ffff83013cf12000
> > (XEN) context[40] = 0_0
> > (XEN) ctxt_entry[40] not present
> > (XEN) [VT-D]iommu.c:796: DMAR:[DMA Write] Request device [05:08.0]
fault
> > addr 206003000, iommu reg = ffff82c3fff57000
> > (XEN) DMAR:[fault reason 02h] Present bit in context entry is clear
> > (XEN) print_vtd_entries: iommu = ffff83013fffaee0 bdf = 5:8.0 gmfn
> > 206003
> > (XEN) root_entry = ffff83013ff37000
> > (XEN) root_entry[5] = 13cf12001
> > (XEN) context = ffff83013cf12000
> > (XEN) context[40] = 0_0
> > (XEN) ctxt_entry[40] not present
> > (XEN) [VT-D]iommu.c:821: iommu_fault_status: Primary Pending Fault
> > (XEN) [VT-D]iommu.c:796: DMAR:[DMA Write] Request device [05:08.0]
fault
> > addr 20583e000, iommu reg = ffff82c3fff57000
> > (XEN) DMAR:[fault reason 02h] Present bit in context entry is clear
> > (XEN) print_vtd_entries: iommu = ffff83013fffaee0 bdf = 5:8.0 gmfn
> > 20583e
> > (XEN) root_entry = ffff83013ff37000
> > (XEN) root_entry[5] = 13cf12001
> > (XEN) context = ffff83013cf12000
> > (XEN) context[40] = 0_0
> > (XEN) ctxt_entry[40] not present
> > (XEN) [VT-D]iommu.c:796: DMAR:[DMA Write] Request device [05:08.0]
fault
> > addr 205615000, iommu reg = ffff82c3fff57000
> > (XEN) DMAR:[fault reason 02h] Present bit in context entry is clear
> > (XEN) print_vtd_entries: iommu = ffff83013fffaee0 bdf = 5:8.0 gmfn
> > 205615
> > (XEN) root_entry = ffff83013ff37000
> > (XEN) root_entry[5] = 13cf12001
> > (XEN) context = ffff83013cf12000
> > (XEN) context[40] = 0_0
> > (XEN) ctxt_entry[40] not present
> > (XEN) [VT-D]iommu.c:796: DMAR:[DMA Write] Request device [05:08.0]
fault
> > addr 204265000, iommu reg = ffff82c3fff57000
> > (XEN) DMAR:[fault reason 02h] Present bit in context entry is clear
> > (XEN) print_vtd_entries: iommu = ffff83013fffaee0 bdf = 5:8.0 gmfn
> > 204265
> > (XEN) root_entry = ffff83013ff37000
> > (XEN) root_entry[5] = 13cf12001
> > (XEN) context = ffff83013cf12000
> > (XEN) context[40] = 0_0
> > (XEN) ctxt_entry[40] not present
> > (XEN) [VT-D]iommu.c:821: iommu_fault_status: Primary Pending Fault
> > (XEN) [VT-D]iommu.c:796: DMAR:[DMA Write] Request device [05:08.0]
fault
> > addr 207498000, iommu reg = ffff82c3fff57000
> > (XEN) DMAR:[fault reason 02h] Present bit in context entry is clear
> > (XEN) print_vtd_entries: iommu = ffff83013fffaee0 bdf = 5:8.0 gmfn
> > 207498
> > (XEN) root_entry = ffff83013ff37000
> > (XEN) root_entry[5] = 13cf12001
> > (XEN) context = ffff83013cf12000
> > (XEN) context[40] = 0_0
> > (XEN) ctxt_entry[40] not present
> > (XEN) [VT-D]iommu.c:821: iommu_fault_status: Primary Pending Fault
> > (XEN) [VT-D]iommu.c:796: DMAR:[DMA Write] Request device [05:08.0]
fault
> > addr 2049d1000, iommu reg = ffff82c3fff57000
> > (XEN) DMAR:[fault reason 02h] Present bit in context entry is clear
> > (XEN) print_vtd_entries: iommu = ffff83013fffaee0 bdf = 5:8.0 gmfn
> > 2049d1
> > (XEN) root_entry = ffff83013ff37000
> > (XEN) root_entry[5] = 13cf12001
> > (XEN) context = ffff83013cf12000
> > (XEN) context[40] = 0_0
> > (XEN) ctxt_entry[40] not present
> > (XEN) [VT-D]iommu.c:821: iommu_fault_status: Primary Pending Fault
> > (XEN) [VT-D]iommu.c:796: DMAR:[DMA Write] Request device [05:08.0]
fault
> > addr 20488e000, iommu reg = ffff82c3fff57000
> > (XEN) DMAR:[fault reason 02h] Present bit in context entry is clear
> > (XEN) print_vtd_entries: iommu = ffff83013fffaee0 bdf = 5:8.0 gmfn
> > 20488e
> > (XEN) root_entry = ffff83013ff37000
> > (XEN) root_entry[5] = 13cf12001
> > (XEN) context = ffff83013cf12000
> > (XEN) context[40] = 0_0
> > (XEN) ctxt_entry[40] not present
> > (XEN) [VT-D]iommu.c:821: iommu_fault_status: Primary Pending Fault
> > (XEN) [VT-D]iommu.c:796: DMAR:[DMA Write] Request device [05:08.0]
fault
> > addr 205495000, iommu reg = ffff82c3fff57000
> > (XEN) DMAR:[fault reason 02h] Present bit in context entry is clear
> > (XEN) print_vtd_entries: iommu = ffff83013fffaee0 bdf = 5:8.0 gmfn
> > 205495
> > (XEN) root_entry = ffff83013ff37000
> > (XEN) root_entry[5] = 13cf12001
> > (XEN) context = ffff83013cf12000
> > (XEN) context[40] = 0_0
> > (XEN) ctxt_entry[40] not present
> > (XEN) [VT-D]iommu.c:821: iommu_fault_status: Primary Pending Fault
> > (XEN) [VT-D]iommu.c:796: DMAR:[DMA Write] Request device [05:08.0]
fault
> > addr 2072d8000, iommu reg = ffff82c3fff57000
> > (XEN) DMAR:[fault reason 02h] Present bit in context entry is clear
> > (XEN) print_vtd_entries: iommu = ffff83013fffaee0 bdf = 5:8.0 gmfn
> > 2072d8
> > (XEN) root_entry = ffff83013ff37000
> > (XEN) root_entry[5] = 13cf12001
> > (XEN) context = ffff83013cf12000
> > (XEN) context[40] = 0_0
> > (XEN) ctxt_entry[40] not present
> > (XEN) [VT-D]iommu.c:821: iommu_fault_status: Primary Pending Fault
> > (XEN) [VT-D]iommu.c:796: DMAR:[DMA Write] Request device [05:08.0]
fault
> > addr 2055ae000, iommu reg = ffff82c3fff57000
> > (XEN) DMAR:[fault reason 02h] Present bit in context entry is clear
> > (XEN) print_vtd_entries: iommu = ffff83013fffaee0 bdf = 5:8.0 gmfn
> > 2055ae
> > (XEN) root_entry = ffff83013ff37000
> > (XEN) root_entry[5] = 13cf12001
> > (XEN) context = ffff83013cf12000
> > (XEN) context[40] = 0_0
> > (XEN) ctxt_entry[40] not present
> > (XEN) [VT-D]iommu.c:821: iommu_fault_status: Primary Pending Fault
> > (XEN) [VT-D]iommu.c:796: DMAR:[DMA Write] Request device [05:08.0]
fault
> > addr 205544000, iommu reg = ffff82c3fff57000
> > (XEN) DMAR:[fault reason 02h] Present bit in context entry is clear
> > (XEN) print_vtd_entries: iommu = ffff83013fffaee0 bdf = 5:8.0 gmfn
> > 205544
> > (XEN) root_entry = ffff83013ff37000
> > (XEN) root_entry[5] = 13cf12001
> > (XEN) context = ffff83013cf12000
> > (XEN) context[40] = 0_0
> > (XEN) ctxt_entry[40] not present
> > (XEN) [VT-D]iommu.c:796: DMAR:[DMA Write] Request device [05:08.0]
fault
> > addr 204865000, iommu reg = ffff82c3fff57000
> > (XEN) DMAR:[fault reason 02h] Present bit in context entry is clear
> > (XEN) print_vtd_entries: iommu = ffff83013fffaee0 bdf = 5:8.0 gmfn
> > 204865
> > (XEN) root_entry = ffff83013ff37000
> > (XEN) root_entry[5] = 13cf12001
> > (XEN) context = ffff83013cf12000
> > (XEN) context[40] = 0_0
> > (XEN) ctxt_entry[40] not present
> > (XEN) [VT-D]iommu.c:821: iommu_fault_status: Primary Pending Fault
> > (XEN) [VT-D]iommu.c:796: DMAR:[DMA Write] Request device [05:08.0]
fault
> > addr 2074be000, iommu reg = ffff82c3fff57000
> > (XEN) DMAR:[fault reason 02h] Present bit in context entry is clear
> > (XEN) print_vtd_entries: iommu = ffff83013fffaee0 bdf = 5:8.0 gmfn
> > 2074be
> > (XEN) root_entry = ffff83013ff37000
> > (XEN) root_entry[5] = 13cf12001
> > (XEN) context = ffff83013cf12000
> > (XEN) context[40] = 0_0
> > (XEN) ctxt_entry[40] not present
> >
> > (XEN) [VT-D]iommu.c:796: DMAR:[DMA Write] Request device [05:08.0]
fault
> > addr 204865000, iommu reg = ffff82c3fff57000
> > (XEN) DMAR:[fault reason 02h] Present bit in context entry is clear
> > (XEN) print_vtd_entries: iommu = ffff83013fffaee0 bdf = 5:8.0 gmfn
> > 204865
> > (XEN) root_entry = ffff83013ff37000
> > (XEN) root_entry[5] = 13cf12001
> > (XEN) context = ffff83013cf12000
> > (XEN) context[40] = 0_0
> > (XEN) ctxt_entry[40] not present
> > (XEN) [VT-D]iommu.c:821: iommu_fault_status: Primary Pending Fault
> > (XEN) [VT-D]iommu.c:796: DMAR:[DMA Write] Request device [05:08.0]
fault
> > addr 2074be000, iommu reg = ffff82c3fff57000
> > (XEN) DMAR:[fault reason 02h] Present bit in context entry is clear
> > (XEN) print_vtd_entries: iommu = ffff83013fffaee0 bdf = 5:8.0 gmfn
> > 2074be
> > (XEN) root_entry = ffff83013ff37000
> > (XEN) root_entry[5] = 13cf12001
> > (XEN) context = ffff83013cf12000
> > (XEN) context[40] = 0_0
> > (XEN) ctxt_entry[40] not present
> >
> > (XEN) [VT-D]iommu.c:796: DMAR:[DMA Write] Request device [05:08.0]
fault
> > addr 204865000, iommu reg = ffff82c3fff57000
> > (XEN) DMAR:[fault reason 02h] Present bit in context entry is clear
> > (XEN) print_vtd_entries: iommu = ffff83013fffaee0 bdf = 5:8.0 gmfn
> > 204865
> > (XEN) root_entry = ffff83013ff37000
> > (XEN) root_entry[5] = 13cf12001
> > (XEN) context = ffff83013cf12000
> > (XEN) context[40] = 0_0
> > (XEN) ctxt_entry[40] not present
> > (XEN) [VT-D]iommu.c:821: iommu_fault_status: Primary Pending Fault
> > (XEN) [VT-D]iommu.c:796: DMAR:[DMA Write] Request device [05:08.0]
fault
> > addr 2074be000, iommu reg = ffff82c3fff57000
> > (XEN) DMAR:[fault reason 02h] Present bit in context entry is clear
> > (XEN) print_vtd_entries: iommu = ffff83013fffaee0 bdf = 5:8.0 gmfn
> > 2074be
> > (XEN) root_entry = ffff83013ff37000
> > (XEN) root_entry[5] = 13cf12001
> > (XEN) context = ffff83013cf12000
> > (XEN) context[40] = 0_0
> > (XEN) ctxt_entry[40] not present
> >
> > (XEN) [VT-D]iommu.c:796: DMAR:[DMA Write] Request device [05:08.0]
fault
> > addr 204865000, iommu reg = ffff82c3fff57000
> > (XEN) DMAR:[fault reason 02h] Present bit in context entry is clear
> > (XEN) print_vtd_entries: iommu = ffff83013fffaee0 bdf = 5:8.0 gmfn
> > 204865
> > (XEN) root_entry = ffff83013ff37000
> > (XEN) root_entry[5] = 13cf12001
> > (XEN) context = ffff83013cf12000
> > (XEN) context[40] = 0_0
> > (XEN) ctxt_entry[40] not present
> > (XEN) [VT-D]iommu.c:821: iommu_fault_status: Primary Pending Fault
> > (XEN) [VT-D]iommu.c:796: DMAR:[DMA Write] Request device [05:08.0]
fault
> > addr 2074be000, iommu reg = ffff82c3fff57000
> > (XEN) DMAR:[fault reason 02h] Present bit in context entry is clear
> > (XEN) print_vtd_entries: iommu = ffff83013fffaee0 bdf = 5:8.0 gmfn
> > 2074be
> > (XEN) root_entry = ffff83013ff37000
> > (XEN) root_entry[5] = 13cf12001
> > (XEN) context = ffff83013cf12000
> > (XEN) context[40] = 0_0
> > (XEN) ctxt_entry[40] not present
> >
> > (XEN) [VT-D]iommu.c:796: DMAR:[DMA Write] Request device [05:08.0]
fault
> > addr 204865000, iommu reg = ffff82c3fff57000
> > (XEN) DMAR:[fault reason 02h] Present bit in context entry is clear
> > (XEN) print_vtd_entries: iommu = ffff83013fffaee0 bdf = 5:8.0 gmfn
> > 204865
> > (XEN) root_entry = ffff83013ff37000
> > (XEN) root_entry[5] = 13cf12001
> > (XEN) context = ffff83013cf12000
> > (XEN) context[40] = 0_0
> > (XEN) ctxt_entry[40] not present
> > (XEN) [VT-D]iommu.c:821: iommu_fault_status: Primary Pending Fault
> > (XEN) [VT-D]iommu.c:796: DMAR:[DMA Write] Request device [05:08.0]
fault
> > addr 2074be000, iommu reg = ffff82c3fff57000
> > (XEN) DMAR:[fault reason 02h] Present bit in context entry is clear
> > (XEN) print_vtd_entries: iommu = ffff83013fffaee0 bdf = 5:8.0 gmfn
> > 2074be
> > (XEN) root_entry = ffff83013ff37000
> > (XEN) root_entry[5] = 13cf12001
> > (XEN) context = ffff83013cf12000
> > (XEN) context[40] = 0_0
> > (XEN) ctxt_entry[40] not present
> >
> > (XEN) [VT-D]iommu.c:796: DMAR:[DMA Write] Request device [05:08.0]
fault
> > addr 204865000, iommu reg = ffff82c3fff57000
> > (XEN) DMAR:[fault reason 02h] Present bit in context entry is clear
> > (XEN) print_vtd_entries: iommu = ffff83013fffaee0 bdf = 5:8.0 gmfn
> > 204865
> > (XEN) root_entry = ffff83013ff37000
> > (XEN) root_entry[5] = 13cf12001
> > (XEN) context = ffff83013cf12000
> > (XEN) context[40] = 0_0
> > (XEN) ctxt_entry[40] not present
> > (XEN) [VT-D]iommu.c:821: iommu_fault_status: Primary Pending Fault
> > (XEN) [VT-D]iommu.c:796: DMAR:[DMA Write] Request device [05:08.0]
fault
> > addr 2074be000, iommu reg = ffff82c3fff57000
> > (XEN) DMAR:[fault reason 02h] Present bit in context entry is clear
> > (XEN) print_vtd_entries: iommu = ffff83013fffaee0 bdf = 5:8.0 gmfn
> > 2074be
> > (XEN) root_entry = ffff83013ff37000
> > (XEN) root_entry[5] = 13cf12001
> > (XEN) context = ffff83013cf12000
> > (XEN) context[40] = 0_0
> > (XEN) ctxt_entry[40] not present
> >
> > (XEN) [VT-D]iommu.c:796: DMAR:[DMA Write] Request device [05:08.0]
fault
> > addr 204865000, iommu reg = ffff82c3fff57000
> > (XEN) DMAR:[fault reason 02h] Present bit in context entry is clear
> > (XEN) print_vtd_entries: iommu = ffff83013fffaee0 bdf = 5:8.0 gmfn
> > 204865
> > (XEN) root_entry = ffff83013ff37000
> > (XEN) root_entry[5] = 13cf12001
> > (XEN) context = ffff83013cf12000
> > (XEN) context[40] = 0_0
> > (XEN) ctxt_entry[40] not present
> > (XEN) [VT-D]iommu.c:821: iommu_fault_status: Primary Pending Fault
> > (XEN) [VT-D]iommu.c:796: DMAR:[DMA Write] Request device [05:08.0]
fault
> > addr 2074be000, iommu reg = ffff82c3fff57000
> > (XEN) DMAR:[fault reason 02h] Present bit in context entry is clear
> > (XEN) print_vtd_entries: iommu = ffff83013fffaee0 bdf = 5:8.0 gmfn
> > 2074be
> > (XEN) root_entry = ffff83013ff37000
> > (XEN) root_entry[5] = 13cf12001
> > (XEN) context = ffff83013cf12000
> > (XEN) context[40] = 0_0
> > (XEN) ctxt_entry[40] not present
> >
> > (XEN) context[40] = 0_0
> > (XEN) ctxt_entry[40] not present
> > (XEN) [VT-D]iommu.c:796: DMAR:[DMA Write] Request device [05:08.0]
fault
> > addr 204865000, iommu reg = ffff82c3fff57000
> > (XEN) DMAR:[fault reason 02h] Present bit in context entry is clear
> > (XEN) print_vtd_entries: iommu = ffff83013fffaee0 bdf = 5:8.0 gmfn
> > 204865
> > (XEN) root_entry = ffff83013ff37000
> > (XEN) root_entry[5] = 13cf12001
> > (XEN) context = ffff83013cf12000
> > (XEN) context[40] = 0_0
> > (XEN) ctxt_entry[40] not present
> > (XEN) [VT-D]iommu.c:821: iommu_fault_status: Primary Pending Fault
> > (XEN) [VT-D]iommu.c:796: DMAR:[DMA Write] Request device [05:08.0]
fault
> > addr 2074be000, iommu reg = ffff82c3fff57000
> > (XEN) DMAR:[fault reason 02h] Present bit in context entry is clear
> > (XEN) print_vtd_entries: iommu = ffff83013fffaee0 bdf = 5:8.0 gmfn
> > 2074be
> > (XEN) root_entry = ffff83013ff37000
> > (XEN) root_entry[5] = 13cf12001
> > (XEN) context = ffff83013cf12000
> > (XEN) context[40] = 0_0
> > (XEN) ctxt_entry[40] not present
> >
> > (XEN) context[40] = 0_0
> > (XEN) ctxt_entry[40] not present
> > (XEN) [VT-D]iommu.c:796: DMAR:[DMA Write] Request device [05:08.0]
fault
> > addr 204865000, iommu reg = ffff82c3fff57000
> > (XEN) DMAR:[fault reason 02h] Present bit in context entry is clear
> > (XEN) print_vtd_entries: iommu = ffff83013fffaee0 bdf = 5:8.0 gmfn
> > 204865
> > (XEN) root_entry = ffff83013ff37000
> > (XEN) root_entry[5] = 13cf12001
> > (XEN) context = ffff83013cf12000
> > (XEN) context[40] = 0_0
> > (XEN) ctxt_entry[40] not present
> > (XEN) [VT-D]iommu.c:821: iommu_fault_status: Primary Pending Fault
> > (XEN) [VT-D]iommu.c:796: DMAR:[DMA Write] Request device [05:08.0]
fault
> > addr 2074be000, iommu reg = ffff82c3fff57000
> > (XEN) DMAR:[fault reason 02h] Present bit in context entry is clear
> > (XEN) print_vtd_entries: iommu = ffff83013fffaee0 bdf = 5:8.0 gmfn
> > 2074be
> > (XEN) root_entry = ffff83013ff37000
> > (XEN) root_entry[5] = 13cf12001
> > (XEN) context = ffff83013cf12000
> > (XEN) context[40] = 0_0
> > (XEN) ctxt_entry[40] not present
> >
> > (XEN) context[40] = 0_0
> > (XEN) ctxt_entry[40] not present
> > (XEN) [VT-D]iommu.c:796: DMAR:[DMA Write] Request device [05:08.0]
fault
> > addr 204865000, iommu reg = ffff82c3fff57000
> > (XEN) DMAR:[fault reason 02h] Present bit in context entry is clear
> > (XEN) print_vtd_entries: iommu = ffff83013fffaee0 bdf = 5:8.0 gmfn
> > 204865
> > (XEN) root_entry = ffff83013ff37000
> > (XEN) root_entry[5] = 13cf12001
> > (XEN) context = ffff83013cf12000
> > (XEN) context[40] = 0_0
> > (XEN) ctxt_entry[40] not present
> > (XEN) [VT-D]iommu.c:821: iommu_fault_status: Primary Pending Fault
> > (XEN) [VT-D]iommu.c:796: DMAR:[DMA Write] Request device [05:08.0]
fault
> > addr 2074be000, iommu reg = ffff82c3fff57000
> > (XEN) DMAR:[fault reason 02h] Present bit in context entry is clear
> > (XEN) print_vtd_entries: iommu = ffff83013fffaee0 bdf = 5:8.0 gmfn
> > 2074be
> > (XEN) root_entry = ffff83013ff37000
> > (XEN) root_entry[5] = 13cf12001
> > (XEN) context = ffff83013cf12000
> > (XEN) context[40] = 0_0
> > (XEN) ctxt_entry[40] not present
> >
> > (XEN) context[40] = 0_0
> > (XEN) ctxt_entry[40] not present
> > (XEN) [VT-D]iommu.c:796: DMAR:[DMA Write] Request device [05:08.0]
fault
> > addr 204865000, iommu reg = ffff82c3fff57000
> > (XEN) DMAR:[fault reason 02h] Present bit in context entry is clear
> > (XEN) print_vtd_entries: iommu = ffff83013fffaee0 bdf = 5:8.0 gmfn
> > 204865
> > (XEN) root_entry = ffff83013ff37000
> > (XEN) root_entry[5] = 13cf12001
> > (XEN) context = ffff83013cf12000
> > (XEN) context[40] = 0_0
> > (XEN) ctxt_entry[40] not present
> > (XEN) [VT-D]iommu.c:821: iommu_fault_status: Primary Pending Fault
> > (XEN) [VT-D]iommu.c:796: DMAR:[DMA Write] Request device [05:08.0]
fault
> > addr 2074be000, iommu reg = ffff82c3fff57000
> > (XEN) DMAR:[fault reason 02h] Present bit in context entry is clear
> > (XEN) print_vtd_entries: iommu = ffff83013fffaee0 bdf = 5:8.0 gmfn
> > 2074be
> > (XEN) root_entry = ffff83013ff37000
> > (XEN) root_entry[5] = 13cf12001
> > (XEN) context = ffff83013cf12000
> > (XEN) context[40] = 0_0
> > (XEN) ctxt_entry[40] not present
> >
> >
> > _______________________________________________
> > Xen-devel mailing list
> > Xen-devel@lists.xensource.com
> > http://lists.xensource.com/xen-devel
_______________________________________________
Xen-devel mailing list
Xen-devel@lists.xensource.com
http://lists.xensource.com/xen-devel
Pasi Kärkkäinen
2010-May-30 18:38 UTC
Re: [Xen-devel] iommuu/vt-d issues with LSI MegaSAS (PERC5i) [Full log Xen + dom0 kernel]
On Sun, May 30, 2010 at 11:33:05AM -0700, M. Nunberg wrote:> Here is the full log, kernel + xen >Thanks! This should be detailed enough to figure out what happens.. -- Pasi> \ \/ /___ _ __ | || | / _ \ / | _ __ ___/ | > \ // _ \ ''_ \ | || |_| | | || |__| ''__/ __| | > / \ __/ | | | |__ _| |_| || |__| | | (__| | > /_/\_\___|_| |_| |_|(_)___(_)_| |_| \___|_| > > (XEN) Xen version 4.0.1-rc1 (mordy@) (gcc version 4.3.2 (Debian > 4.3.2-1.1) ) Fri May 28 16:46:04 PDT 2010 > (XEN) Latest ChangeSet: Sat May 22 07:18:16 2010 +0100 > 21162:370fd9f97c70 > (XEN) Console output is synchronous. > (XEN) Command line: iommu=verbose loglvl=all guest_loglvl=all > sync_console console_to_rint com1=115200,8n1 console=com1 > (XEN) Video information: > (XEN) VGA is text mode 80x25, font 8x16 > (XEN) VBE/DDC methods: none; EDID transfer time: 0 seconds > (XEN) EDID info not retrieved because no DDC retrieval method detected > (XEN) Disc information: > (XEN) Found 1 MBR signatures > (XEN) Found 1 EDD information structures > (XEN) Xen-e820 RAM map: > (XEN) 0000000000000000 - 000000000009a000 (usable) > (XEN) 000000000009a000 - 00000000000a0000 (reserved) > (XEN) 00000000000e0000 - 0000000000100000 (reserved) > (XEN) 0000000000100000 - 00000000bf760000 (usable) > (XEN) 00000000bf76e000 - 00000000bf770000 type 9 > (XEN) 00000000bf770000 - 00000000bf77e000 (ACPI data) > (XEN) 00000000bf77e000 - 00000000bf7d0000 (ACPI NVS) > (XEN) 00000000bf7d0000 - 00000000bf7e0000 (reserved) > (XEN) 00000000bf7ec000 - 00000000c0000000 (reserved) > (XEN) 00000000fee00000 - 00000000fee01000 (reserved) > (XEN) 00000000ffc00000 - 0000000100000000 (reserved) > (XEN) 0000000100000000 - 0000000340000000 (usable) > (XEN) ACPI: RSDP 000F9E10, 0024 (r2 ACPIAM) > (XEN) ACPI: XSDT BF770100, 0094 (r1 NEC 20090424 MSFT > 97) > (XEN) ACPI: FACP BF770290, 00F4 (r4 042409 FACP1917 20090424 MSFT > 97) > (XEN) ACPI: DSDT BF770670, 5BFB (r2 10601 10601000 0 INTL > 20051117) > (XEN) ACPI: FACS BF77E000, 0040 > (XEN) ACPI: APIC BF770390, 00D2 (r2 042409 APIC1917 20090424 MSFT > 97) > (XEN) ACPI: MCFG BF770470, 003C (r1 042409 OEMMCFG 20090424 MSFT > 97) > (XEN) ACPI: SLIC BF7704B0, 0176 (r1 NEC 20090424 MSFT > 97) > (XEN) ACPI: ERST BF770630, 0040 (r1 042409 WHEA1917 20090424 MSFT > 97) > (XEN) ACPI: OEMB BF77E040, 007B (r1 042409 OEMB1917 20090424 MSFT > 97) > (XEN) ACPI: SRAT BF77A670, 01D0 (r1 042409 OEMSRAT 1 INTL > 1) > (XEN) ACPI: HPET BF77A840, 0038 (r1 042409 OEMHPET 20090424 MSFT > 97) > (XEN) ACPI: DMAR BF77E0C0, 0118 (r1 AMI OEMDMAR 1 MSFT > 97) > (XEN) ACPI: SSDT BF781DF0, 0363 (r1 DpgPmm CpuPm 12 INTL > 20051117) > (XEN) ACPI: EINJ BF77A880, 0130 (r1 AMIER AMI_EINJ 20090424 MSFT > 97) > (XEN) ACPI: BERT BF77AA10, 0030 (r1 AMIER AMI_BERT 20090424 MSFT > 97) > (XEN) ACPI: ERST BF77AA40, 01B0 (r1 AMIER AMI_ERST 20090424 MSFT > 97) > (XEN) ACPI: HEST BF77ABF0, 00A8 (r1 AMIER AMI_HEST 20090424 MSFT > 97) > (XEN) System RAM: 12278MB (12573672kB) > (XEN) SRAT: PXM 0 -> APIC 0 -> Node 0 > (XEN) SRAT: PXM 0 -> APIC 2 -> Node 0 > (XEN) SRAT: PXM 0 -> APIC 4 -> Node 0 > (XEN) SRAT: PXM 0 -> APIC 6 -> Node 0 > (XEN) SRAT: PXM 0 -> APIC 1 -> Node 0 > (XEN) SRAT: PXM 0 -> APIC 3 -> Node 0 > (XEN) SRAT: PXM 0 -> APIC 5 -> Node 0 > (XEN) SRAT: PXM 0 -> APIC 7 -> Node 0 > (XEN) SRAT: PXM 1 -> APIC 16 -> Node 1 > (XEN) SRAT: PXM 1 -> APIC 18 -> Node 1 > (XEN) SRAT: PXM 1 -> APIC 20 -> Node 1 > (XEN) SRAT: PXM 1 -> APIC 22 -> Node 1 > (XEN) SRAT: PXM 1 -> APIC 17 -> Node 1 > (XEN) SRAT: PXM 1 -> APIC 19 -> Node 1 > (XEN) SRAT: PXM 1 -> APIC 21 -> Node 1 > (XEN) SRAT: PXM 1 -> APIC 23 -> Node 1 > (XEN) SRAT: Node 0 PXM 0 0-a0000 > (XEN) SRAT: Node 0 PXM 0 100000-c0000000 > (XEN) SRAT: Node 0 PXM 0 100000000-1c0000000 > (XEN) SRAT: Node 1 PXM 1 1c0000000-340000000 > (XEN) NUMA: Allocated memnodemap from 33fdfb000 - 33fdff000 > (XEN) NUMA: Using 8 for the hash shift. > (XEN) Domain heap initialised DMA width 30 bits > (XEN) found SMP MP-table at 000ff780 > (XEN) DMI present. > (XEN) Using APIC driver default > (XEN) ACPI: PM-Timer IO Port: 0x808 > (XEN) ACPI: ACPI SLEEP INFO: pm1x_cnt[804,0], pm1x_evt[800,0] > (XEN) ACPI: wakeup_vec[bf77e00c], vec_size[20] > (XEN) ACPI: Local APIC address 0xfee00000 > (XEN) ACPI: LAPIC (acpi_id[0x01] lapic_id[0x00] enabled) > (XEN) Processor #0 7:10 APIC version 21 > (XEN) ACPI: LAPIC (acpi_id[0x02] lapic_id[0x10] enabled) > (XEN) Processor #16 7:10 APIC version 21 > (XEN) ACPI: LAPIC (acpi_id[0x03] lapic_id[0x02] enabled) > (XEN) Processor #2 7:10 APIC version 21 > (XEN) ACPI: LAPIC (acpi_id[0x04] lapic_id[0x12] enabled) > (XEN) Processor #18 7:10 APIC version 21 > (XEN) ACPI: LAPIC (acpi_id[0x05] lapic_id[0x04] enabled) > (XEN) Processor #4 7:10 APIC version 21 > (XEN) ACPI: LAPIC (acpi_id[0x06] lapic_id[0x14] enabled) > (XEN) Processor #20 7:10 APIC version 21 > (XEN) ACPI: LAPIC (acpi_id[0x07] lapic_id[0x06] enabled) > (XEN) Processor #6 7:10 APIC version 21 > (XEN) ACPI: LAPIC (acpi_id[0x08] lapic_id[0x16] enabled) > (XEN) Processor #22 7:10 APIC version 21 > (XEN) ACPI: LAPIC (acpi_id[0x09] lapic_id[0x01] enabled) > (XEN) Processor #1 7:10 APIC version 21 > (XEN) ACPI: LAPIC (acpi_id[0x0a] lapic_id[0x11] enabled) > (XEN) Processor #17 7:10 APIC version 21 > (XEN) ACPI: LAPIC (acpi_id[0x0b] lapic_id[0x03] enabled) > (XEN) Processor #3 7:10 APIC version 21 > (XEN) ACPI: LAPIC (acpi_id[0x0c] lapic_id[0x13] enabled) > (XEN) Processor #19 7:10 APIC version 21 > (XEN) ACPI: LAPIC (acpi_id[0x0d] lapic_id[0x05] enabled) > (XEN) Processor #5 7:10 APIC version 21 > (XEN) ACPI: LAPIC (acpi_id[0x0e] lapic_id[0x15] enabled) > (XEN) Processor #21 7:10 APIC version 21 > (XEN) ACPI: LAPIC (acpi_id[0x0f] lapic_id[0x07] enabled) > (XEN) Processor #7 7:10 APIC version 21 > (XEN) ACPI: LAPIC (acpi_id[0x10] lapic_id[0x17] enabled) > (XEN) Processor #23 7:10 APIC version 21 > (XEN) ACPI: LAPIC_NMI (acpi_id[0xff] dfl dfl lint[0x1]) > (XEN) Overriding APIC driver with bigsmp > (XEN) ACPI: IOAPIC (id[0x08] address[0xfec00000] gsi_base[0]) > (XEN) IOAPIC[0]: apic_id 8, version 32, address 0xfec00000, GSI 0-23 > (XEN) ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl) > (XEN) ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 20 low level) > (XEN) ACPI: IRQ0 used by override. > (XEN) ACPI: IRQ2 used by override. > (XEN) ACPI: IRQ9 used by override. > (XEN) Enabling APIC mode: Phys. Using 1 I/O APICs > (XEN) ACPI: HPET id: 0xffffffff base: 0xfed00000 > (XEN) [VT-D]dmar.c:679: Host address width 40 > (XEN) [VT-D]dmar.c:694: found ACPI_DMAR_DRHD: > (XEN) [VT-D]dmar.c:398: dmaru->address = fbffe000 > (XEN) [VT-D]dmar.c:340: IOAPIC: f0:1f.7 > (XEN) [VT-D]dmar.c:411: flags: INCLUDE_ALL > (XEN) [VT-D]dmar.c:699: found ACPI_DMAR_RMRR: > (XEN) [VT-D]dmar.c:334: endpoint: 0:1d.0 > (XEN) [VT-D]dmar.c:334: endpoint: 0:1d.1 > (XEN) [VT-D]dmar.c:334: endpoint: 0:1d.2 > (XEN) [VT-D]dmar.c:334: endpoint: 0:1d.7 > (XEN) [VT-D]dmar.c:334: endpoint: 0:1a.0 > (XEN) [VT-D]dmar.c:334: endpoint: 0:1a.1 > (XEN) [VT-D]dmar.c:334: endpoint: 0:1a.2 > (XEN) [VT-D]dmar.c:334: endpoint: 0:1a.7 > (XEN) [VT-D]dmar.c:571: RMRR region: base_addr ec000 end_address effff > (XEN) [VT-D]dmar.c:699: found ACPI_DMAR_RMRR: > (XEN) [VT-D]dmar.c:334: endpoint: 0:1d.0 > (XEN) [VT-D]dmar.c:334: endpoint: 0:1d.1 > (XEN) [VT-D]dmar.c:334: endpoint: 0:1d.2 > (XEN) [VT-D]dmar.c:334: endpoint: 0:1d.7 > (XEN) [VT-D]dmar.c:334: endpoint: 0:1a.0 > (XEN) [VT-D]dmar.c:334: endpoint: 0:1a.1 > (XEN) [VT-D]dmar.c:334: endpoint: 0:1a.2 > (XEN) [VT-D]dmar.c:334: endpoint: 0:1a.7 > (XEN) [VT-D]dmar.c:571: RMRR region: base_addr bf7ec000 end_address > bf7fffff > (XEN) [VT-D]dmar.c:704: found ACPI_DMAR_ATSR: > (XEN) [VT-D]dmar.c:599: atsru->all_ports: 0 > (XEN) [VT-D]dmar.c:320: bridge: 0:1.0 start = 0 sec = 1 sub = 1 > (XEN) [VT-D]dmar.c:320: bridge: 0:3.0 start = 0 sec = 2 sub = 2 > (XEN) [VT-D]dmar.c:320: bridge: 0:7.0 start = 0 sec = 3 sub = 3 > (XEN) PCI: MCFG configuration 0: base e0000000 segment 0 buses 0 - 255 > (XEN) PCI: Not using MMCONFIG. > (XEN) Using ACPI (MADT) for SMP configuration information > (XEN) Using scheduler: SMP Credit Scheduler (credit) > (XEN) Detected 2266.784 MHz processor. > (XEN) Initing memory sharing. > (XEN) VMX: Supported advanced features: > (XEN) - APIC MMIO access virtualisation > (XEN) - APIC TPR shadow > (XEN) - Extended Page Tables (EPT) > (XEN) - Virtual-Processor Identifiers (VPID) > (XEN) - Virtual NMI > (XEN) - MSR direct-access bitmap > (XEN) HVM: ASIDs enabled. > (XEN) HVM: VMX enabled > (XEN) HVM: Hardware Assisted Paging detected. > (XEN) Intel machine check reporting enabled > (XEN) [VT-D]iommu.c:1078: drhd->address = fbffe000 iommu->reg > ffff82c3fff57000 > (XEN) [VT-D]iommu.c:1080: cap = c90780106f0462 ecap = f0207e > (XEN) Intel VT-d Snoop Control not supported. > (XEN) Intel VT-d DMA Passthrough not supported. > (XEN) Intel VT-d Queued Invalidation supported. > (XEN) Intel VT-d Interrupt Remapping supported. > (XEN) I/O virtualisation enabled > (XEN) I/O virtualisation for PV guests disabled > (XEN) Total of 16 processors activated. > (XEN) ENABLING IO-APIC IRQs > (XEN) -> Using new ACK method > (XEN) ..TIMER: vector=0xF0 apic1=0 pin1=2 apic2=-1 pin2=-1 > (XEN) TSC is reliable, synchronization unnecessary > (XEN) Platform timer is 14.318MHz HPET > ÿ(XEN) Allocated console ring of 128 KiB. > (XEN) microcode.c:73:d32767 microcode: CPU1 resumed > (XEN) microcode.c:73:d32767 microcode: CPU9 resumed > (XEN) microcode.c:73:d32767 microcode: CPU6 resumed > (XEN) microcode.c:73:d32767 microcode: CPU14 resumed > (XEN) microcode.c:73:d32767 microcode: CPU7 resumed > (XEN) microcode.c:73:d32767 microcode: CPU15 resumed > (XEN) microcode.c:73:d32767 microcode: CPU10 resumed > (XEN) microcode.c:73:d32767 microcode: CPU13 resumed > (XEN) microcode.c:73:d32767 microcode: CPU5 resumed > (XEN) microcode.c:73:d32767 microcode: CPU2 resumed > (XEN) microcode.c:73:d32767 microcode: CPU3 resumed > (XEN) microcode.c:73:d32767 microcode: CPU11 resumed > (XEN) microcode.c:73:d32767 microcode: CPU12 resumed > (XEN) microcode.c:73:d32767 microcode: CPU8 resumed > (XEN) microcode.c:73:d32767 microcode: CPU4 resumed > (XEN) Brought up 16 CPUs > (XEN) Turbo Mode detected! > (XEN) HPET''s MSI mode hasn''t been supported when Interrupt Remapping is > enabled. > (XEN) ACPI sleep modes: S3 > (XEN) mcheck_poll: Machine check polling timer started. > (XEN) [VT-D]iommu.c:1325: d0:PCIe: map bdf = 0:0.0 > (XEN) [VT-D]iommu.c:1325: d0:PCIe: map bdf = 0:14.0 > (XEN) [VT-D]iommu.c:1325: d0:PCIe: map bdf = 0:14.1 > (XEN) [VT-D]iommu.c:1325: d0:PCIe: map bdf = 0:14.2 > (XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = 0:14.3 > (XEN) [VT-D]iommu.c:1325: d0:PCIe: map bdf = 0:16.0 > (XEN) [VT-D]iommu.c:1325: d0:PCIe: map bdf = 0:16.1 > (XEN) [VT-D]iommu.c:1325: d0:PCIe: map bdf = 0:16.2 > (XEN) [VT-D]iommu.c:1325: d0:PCIe: map bdf = 0:16.3 > (XEN) [VT-D]iommu.c:1325: d0:PCIe: map bdf = 0:16.4 > (XEN) [VT-D]iommu.c:1325: d0:PCIe: map bdf = 0:16.5 > (XEN) [VT-D]iommu.c:1325: d0:PCIe: map bdf = 0:16.6 > (XEN) [VT-D]iommu.c:1325: d0:PCIe: map bdf = 0:16.7 > (XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = 0:1a.0 > (XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = 0:1a.1 > (XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = 0:1a.2 > (XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = 0:1a.7 > (XEN) [VT-D]iommu.c:1325: d0:PCIe: map bdf = 0:1b.0 > (XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = 0:1d.0 > (XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = 0:1d.1 > (XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = 0:1d.2 > (XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = 0:1d.7 > (XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = 0:1f.0 > (XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = 0:1f.2 > (XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = 0:1f.3 > (XEN) [VT-D]iommu.c:1325: d0:PCIe: map bdf = 1:0.0 > (XEN) [VT-D]iommu.c:1325: d0:PCIe: map bdf = 3:0.0 > (XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = 5:e.0 > (XEN) [VT-D]iommu.c:1325: d0:PCIe: map bdf = 7:0.0 > (XEN) [VT-D]iommu.c:1325: d0:PCIe: map bdf = 8:0.0 > (XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = fe:0.0 > (XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = fe:0.1 > (XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = fe:2.0 > (XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = fe:2.1 > (XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = fe:2.4 > (XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = fe:2.5 > (XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = fe:3.0 > (XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = fe:3.1 > (XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = fe:3.2 > (XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = fe:3.4 > (XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = fe:4.0 > (XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = fe:4.1 > (XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = fe:4.2 > (XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = fe:4.3 > (XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = fe:5.0 > (XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = fe:5.1 > (XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = fe:5.2 > (XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = fe:5.3 > (XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = fe:6.0 > (XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = fe:6.1 > (XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = fe:6.2 > (XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = fe:6.3 > (XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = ff:0.0 > (XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = ff:0.1 > (XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = ff:2.0 > (XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = ff:2.1 > (XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = ff:2.4 > (XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = ff:2.5 > (XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = ff:3.0 > (XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = ff:3.1 > (XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = ff:3.2 > (XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = ff:3.4 > (XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = ff:4.0 > (XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = ff:4.1 > (XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = ff:4.2 > (XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = ff:4.3 > (XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = ff:5.0 > (XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = ff:5.1 > (XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = ff:5.2 > (XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = ff:5.3 > (XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = ff:6.0 > (XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = ff:6.1 > (XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = ff:6.2 > (XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = ff:6.3 > (XEN) [VT-D]iommu.c:695: iommu_enable_translation: iommu->reg > ffff82c3fff57000 > (XEN) *** LOADING DOMAIN 0 *** > (XEN) Xen kernel: 64-bit, lsb, compat32 > (XEN) Dom0 kernel: 64-bit, PAE, lsb, paddr 0x1000000 -> 0x26b6000 > (XEN) PHYSICAL MEMORY ARRANGEMENT: > (XEN) Dom0 alloc.: 0000000100000000->0000000120000000 (2937039 pages > to be allocated) > (XEN) VIRTUAL MEMORY ARRANGEMENT: > (XEN) Loaded kernel: ffffffff81000000->ffffffff826b6000 > (XEN) Init. ramdisk: ffffffff826b6000->ffffffff8f7d7600 > (XEN) Phys-Mach map: ffffffff8f7d8000->ffffffff90f40678 > (XEN) Start info: ffffffff90f41000->ffffffff90f414b4 > (XEN) Page tables: ffffffff90f42000->ffffffff90fcf000 > (XEN) Boot stack: ffffffff90fcf000->ffffffff90fd0000 > (XEN) TOTAL: ffffffff80000000->ffffffff91400000 > (XEN) ENTRY ADDRESS: ffffffff819be200 > (XEN) Dom0 has maximum 16 VCPUs > (XEN) Scrubbing Free RAM: .done. > (XEN) Xen trace buffers: disabled > (XEN) Std. Loglevel: All > (XEN) Guest Loglevel: All > (XEN) ********************************************** > (XEN) ******* WARNING: CONSOLE OUTPUT IS SYNCHRONOUS > (XEN) ******* This option is intended to aid debugging of Xen by > ensuring > (XEN) ******* that all output is synchronously delivered on the serial > line. > (XEN) ******* However it can introduce SIGNIFICANT latencies and affect > (XEN) ******* timekeeping. It is NOT recommended for production use! > (XEN) ********************************************** > (XEN) 3... 2... 1... > (XEN) *** Serial input -> DOM0 (type ''CTRL-a'' three times to switch > input to Xen) > (XEN) Freed 180kB init memory. > mapping kernel into physical memory > Xen: setup ISA identity maps > about to get started... > Initializing cgroup subsys cpuset > Initializing cgroup subsys cpu > Linux version 2.6.32.13 (mordy@debmed) (gcc version 4.3.2 (Debian > 4.3.2-1.1) ) #3 SMP Fri May 28 13:20:24 PDT 2010 > Command line: root=/dev/mapper/MISC-fedora ro nomodeset console=hvc0 > earlyprintk=xen debug initcall_debug loglvel=10 > KERNEL supported cpus: > Intel GenuineIntel > AMD AuthenticAMD > Centaur CentaurHauls > xen_release_chunk: looking at area pfn bf760-bf76e: 14 pages freed > xen_release_chunk: looking at area pfn bf7e0-bf7ec: 12 pages freed > xen_release_chunk: looking at area pfn c0000-fec00: 257024 pages freed > xen_release_chunk: looking at area pfn fec01-fee00: 511 pages freed > xen_release_chunk: looking at area pfn fee01-ffc00: 3583 pages freed > released 261144 pages of unused memory > BIOS-provided physical RAM map: > Xen: 0000000000000000 - 000000000009a000 (usable) > Xen: 000000000009a000 - 0000000000100000 (reserved) > Xen: 0000000000100000 - 00000000bf760000 (usable) > Xen: 00000000bf76e000 - 00000000bf770000 type 9 > Xen: 00000000bf770000 - 00000000bf77e000 (ACPI data) > Xen: 00000000bf77e000 - 00000000bf7d0000 (ACPI NVS) > Xen: 00000000bf7d0000 - 00000000bf7e0000 (reserved) > Xen: 00000000bf7ec000 - 00000000c0000000 (reserved) > Xen: 00000000fec00000 - 00000000fec01000 (reserved) > Xen: 00000000fee00000 - 00000000fee01000 (reserved) > Xen: 00000000ffc00000 - 0000000100000000 (reserved) > Xen: 0000000100000000 - 00000002ed0cf000 (usable) > bootconsole [xenboot0] enabled > DMI present. > AMI BIOS detected: BIOS may corrupt low RAM, working around it. > e820 update range: 0000000000000000 - 0000000000010000 (usable) ==> > (reserved) > last_pfn = 0x2ed0cf max_arch_pfn = 0x400000000 > x86 PAT enabled: cpu 0, old 0x50100070406, new 0x7010600070106 > last_pfn = 0xbf760 max_arch_pfn = 0x400000000 > initial memory mapped : 0 - 20000000 > init_memory_mapping: 0000000000000000-00000000bf760000 > 0000000000 - 00bf760000 page 4k > kernel direct mapping tables up to bf760000 @ 100000-700000 > init_memory_mapping: 0000000100000000-00000002ed0cf000 > 0100000000 - 02ed0cf000 page 4k > kernel direct mapping tables up to 2ed0cf000 @ 10fcf000-12745000 > RAMDISK: 026b6000 - 0f7d7600 > ACPI: RSDP 00000000000f9e10 00024 (v02 ACPIAM) > ACPI: XSDT 00000000bf770100 00094 (v01 NEC 20090424 MSFT > 00000097) > ACPI: FACP 00000000bf770290 000F4 (v04 042409 FACP1917 20090424 MSFT > 00000097) > ACPI: DSDT 00000000bf770670 05BFB (v02 10601 10601000 00000000 INTL > 20051117) > ACPI: FACS 00000000bf77e000 00040 > ACPI: APIC 00000000bf770390 000D2 (v02 042409 APIC1917 20090424 MSFT > 00000097) > ACPI: MCFG 00000000bf770470 0003C (v01 042409 OEMMCFG 20090424 MSFT > 00000097) > ACPI: SLIC 00000000bf7704b0 00176 (v01 NEC 20090424 MSFT > 00000097) > ACPI: ERST 00000000bf770630 00040 (v01 042409 WHEA1917 20090424 MSFT > 00000097) > ACPI: OEMB 00000000bf77e040 0007B (v01 042409 OEMB1917 20090424 MSFT > 00000097) > ACPI: SRAT 00000000bf77a670 001D0 (v01 042409 OEMSRAT 00000001 INTL > 00000001) > ACPI: HPET 00000000bf77a840 00038 (v01 042409 OEMHPET 20090424 MSFT > 00000097) > ACPI: 00000000bf77e0c0 00118 (v01 AMI OEMDMAR 00000001 MSFT > 00000097) > ACPI: SSDT 00000000bf781df0 00363 (v01 DpgPmm CpuPm 00000012 INTL > 20051117) > ACPI: EINJ 00000000bf77a880 00130 (v01 AMIER AMI_EINJ 20090424 MSFT > 00000097) > ACPI: BERT 00000000bf77aa10 00030 (v01 AMIER AMI_BERT 20090424 MSFT > 00000097) > ACPI: ERST 00000000bf77aa40 001B0 (v01 AMIER AMI_ERST 20090424 MSFT > 00000097) > ACPI: HEST 00000000bf77abf0 000A8 (v01 AMIER AMI_HEST 20090424 MSFT > 00000097) > ACPI: Local APIC address 0xfee00000 > SRAT: PXM 0 -> APIC 0 -> Node 0 > SRAT: PXM 0 -> APIC 2 -> Node 0 > SRAT: PXM 0 -> APIC 4 -> Node 0 > SRAT: PXM 0 -> APIC 6 -> Node 0 > SRAT: PXM 0 -> APIC 1 -> Node 0 > SRAT: PXM 0 -> APIC 3 -> Node 0 > SRAT: PXM 0 -> APIC 5 -> Node 0 > SRAT: PXM 0 -> APIC 7 -> Node 0 > SRAT: PXM 1 -> APIC 16 -> Node 1 > SRAT: PXM 1 -> APIC 18 -> Node 1 > SRAT: PXM 1 -> APIC 20 -> Node 1 > SRAT: PXM 1 -> APIC 22 -> Node 1 > SRAT: PXM 1 -> APIC 17 -> Node 1 > SRAT: PXM 1 -> APIC 19 -> Node 1 > SRAT: PXM 1 -> APIC 21 -> Node 1 > SRAT: PXM 1 -> APIC 23 -> Node 1 > SRAT: Node 0 PXM 0 0-a0000 > SRAT: Node 0 PXM 0 100000-c0000000 > SRAT: Node 0 PXM 0 100000000-1c0000000 > SRAT: Node 2 PXM 257 1c0000000-340000000 > NUMA: Allocated memnodemap from 10000 - 16840 > NUMA: Using 20 for the hash shift. > Bootmem setup node 0 0000000000000000-00000001c0000000 > NODE_DATA [0000000000016840 - 000000000002e83f] > bootmap [000000000002f000 - 0000000000066fff] pages 38 > (10 early reservations) ==> bootmem [0000000000 - 01c0000000] > #0 [0000000000 - 0000001000] BIOS data page ==> [0000000000 - > 0000001000] > #1 [0010f42000 - 0010fcf000] XEN PAGETABLES ==> [0010f42000 - > 0010fcf000] > #2 [0000006000 - 0000008000] TRAMPOLINE ==> [0000006000 - > 0000008000] > #3 [0001000000 - 0002695878] TEXT DATA BSS ==> [0001000000 - > 0002695878] > #4 [00026b6000 - 000f7d7600] RAMDISK ==> [00026b6000 - > 000f7d7600] > #5 [000f7d8000 - 0010f42000] XEN START INFO ==> [000f7d8000 - > 0010f42000] > #6 [0002696000 - 0002696149] BRK ==> [0002696000 - > 0002696149] > #7 [0000100000 - 0000670000] PGTABLE ==> [0000100000 - > 0000670000] > #8 [0010fcf000 - 0011f40000] PGTABLE ==> [0010fcf000 - > 0011f40000] > #9 [0000010000 - 0000016840] MEMNODEMAP ==> [0000010000 - > 0000016840] > Bootmem setup node 2 00000001c0000000-00000002ed0cf000 > NODE_DATA [00000001c0000000 - 00000001c0017fff] > bootmap [00000001c0018000 - 00000001c003da1f] pages 26 > (10 early reservations) ==> bootmem [01c0000000 - 02ed0cf000] > #0 [0000000000 - 0000001000] BIOS data page > #1 [0010f42000 - 0010fcf000] XEN PAGETABLES > #2 [0000006000 - 0000008000] TRAMPOLINE > #3 [0001000000 - 0002695878] TEXT DATA BSS > #4 [00026b6000 - 000f7d7600] RAMDISK > #5 [000f7d8000 - 0010f42000] XEN START INFO > #6 [0002696000 - 0002696149] BRK > #7 [0000100000 - 0000670000] PGTABLE > #8 [0010fcf000 - 0011f40000] PGTABLE > #9 [0000010000 - 0000016840] MEMNODEMAP > found SMP MP-table at [ffff8800000ff780] ff780 > Zone PFN ranges: > DMA 0x00000010 -> 0x00001000 > DMA32 0x00001000 -> 0x00100000 > Normal 0x00100000 -> 0x002ed0cf > Movable zone start PFN for each node > early_node_map[4] active PFN ranges > 0: 0x00000010 -> 0x0000009a > 0: 0x00000100 -> 0x000bf760 > 0: 0x00100000 -> 0x001c0000 > 2: 0x001c0000 -> 0x002ed0cf > On node 0 totalpages: 1570538 > DMA zone: 104 pages used for memmap > DMA zone: 1401 pages reserved > DMA zone: 2473 pages, LIFO batch:0 > DMA32 zone: 26520 pages used for memmap > DMA32 zone: 753608 pages, LIFO batch:31 > Normal zone: 19968 pages used for memmap > Normal zone: 766464 pages, LIFO batch:31 > On node 2 totalpages: 1233103 > Normal zone: 31310 pages used for memmap > Normal zone: 1201793 pages, LIFO batch:31 > ACPI: PM-Timer IO Port: 0x808 > ACPI: Local APIC address 0xfee00000 > ACPI: LAPIC (acpi_id[0x01] lapic_id[0x00] enabled) > ACPI: LAPIC (acpi_id[0x02] lapic_id[0x10] enabled) > ACPI: LAPIC (acpi_id[0x03] lapic_id[0x02] enabled) > ACPI: LAPIC (acpi_id[0x04] lapic_id[0x12] enabled) > ACPI: LAPIC (acpi_id[0x05] lapic_id[0x04] enabled) > ACPI: LAPIC (acpi_id[0x06] lapic_id[0x14] enabled) > ACPI: LAPIC (acpi_id[0x07] lapic_id[0x06] enabled) > ACPI: LAPIC (acpi_id[0x08] lapic_id[0x16] enabled) > ACPI: LAPIC (acpi_id[0x09] lapic_id[0x01] enabled) > ACPI: LAPIC (acpi_id[0x0a] lapic_id[0x11] enabled) > ACPI: LAPIC (acpi_id[0x0b] lapic_id[0x03] enabled) > ACPI: LAPIC (acpi_id[0x0c] lapic_id[0x13] enabled) > ACPI: LAPIC (acpi_id[0x0d] lapic_id[0x05] enabled) > ACPI: LAPIC (acpi_id[0x0e] lapic_id[0x15] enabled) > ACPI: LAPIC (acpi_id[0x0f] lapic_id[0x07] enabled) > ACPI: LAPIC (acpi_id[0x10] lapic_id[0x17] enabled) > ACPI: LAPIC_NMI (acpi_id[0xff] dfl dfl lint[0x1]) > ACPI: IOAPIC (id[0x08] address[0xfec00000] gsi_base[0]) > IOAPIC[0]: apic_id 8, version 0, address 0xfec00000, GSI 0-0 > ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl) > ERROR: Unable to locate IOAPIC for GSI 2 > ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 20 low level) > ERROR: Unable to locate IOAPIC for GSI 20 > Using ACPI (MADT) for SMP configuration information > ACPI: HPET id: 0xffffffff base: 0xfed00000 > SMP: Allowing 16 CPUs, 0 hotplug CPUs > nr_irqs_gsi: 256 > PM: Registered nosave memory: 000000000009a000 - 0000000000100000 > PM: Registered nosave memory: 00000000bf760000 - 00000000bf76e000 > PM: Registered nosave memory: 00000000bf76e000 - 00000000bf770000 > PM: Registered nosave memory: 00000000bf770000 - 00000000bf77e000 > PM: Registered nosave memory: 00000000bf77e000 - 00000000bf7d0000 > PM: Registered nosave memory: 00000000bf7d0000 - 00000000bf7e0000 > PM: Registered nosave memory: 00000000bf7e0000 - 00000000bf7ec000 > PM: Registered nosave memory: 00000000bf7ec000 - 00000000c0000000 > PM: Registered nosave memory: 00000000c0000000 - 00000000fec00000 > PM: Registered nosave memory: 00000000fec00000 - 00000000fec01000 > PM: Registered nosave memory: 00000000fec01000 - 00000000fee00000 > PM: Registered nosave memory: 00000000fee00000 - 00000000fee01000 > PM: Registered nosave memory: 00000000fee01000 - 00000000ffc00000 > PM: Registered nosave memory: 00000000ffc00000 - 0000000100000000 > Allocating PCI resources starting at c0000000 (gap: c0000000:3ec00000) > Booting paravirtualized kernel on Xen > Xen version: 4.0.1-rc1 (preserve-AD) (dom0) > NR_CPUS:512 nr_cpumask_bits:512 nr_cpu_ids:16 nr_node_ids:3 > PERCPU: Embedded 478 pages/cpu @ffff880032052000 s1927128 r8192 d22568 > u1957888 > pcpu-alloc: s1927128 r8192 d22568 u1957888 alloc=478*4096 > pcpu-alloc: [0] 00 [0] 02 [0] 04 [0] 06 [0] 08 [0] 10 [0] 12 [0] 14 > pcpu-alloc: [1] 01 [1] 03 [1] 05 [1] 07 [1] 09 [1] 11 [1] 13 [1] 15 > trying to map vcpu_info 0 at ffff88003205d020, mfn 15205d, offset 32 > cpu 0 using vcpu_info at ffff88003205d020 > trying to map vcpu_info 1 at ffff8801c7c58020, mfn 2e7c58, offset 32 > cpu 1 using vcpu_info at ffff8801c7c58020 > trying to map vcpu_info 2 at ffff88003223b020, mfn 15223b, offset 32 > cpu 2 using vcpu_info at ffff88003223b020 > trying to map vcpu_info 3 at ffff8801c7e36020, mfn 2e7e36, offset 32 > cpu 3 using vcpu_info at ffff8801c7e36020 > trying to map vcpu_info 4 at ffff880032419020, mfn 152419, offset 32 > cpu 4 using vcpu_info at ffff880032419020 > trying to map vcpu_info 5 at ffff8801c8014020, mfn 2e8014, offset 32 > cpu 5 using vcpu_info at ffff8801c8014020 > trying to map vcpu_info 6 at ffff8800325f7020, mfn 1525f7, offset 32 > cpu 6 using vcpu_info at ffff8800325f7020 > trying to map vcpu_info 7 at ffff8801c81f2020, mfn 2e81f2, offset 32 > cpu 7 using vcpu_info at ffff8801c81f2020 > trying to map vcpu_info 8 at ffff8800327d5020, mfn 1527d5, offset 32 > cpu 8 using vcpu_info at ffff8800327d5020 > trying to map vcpu_info 9 at ffff8801c83d0020, mfn 2e83d0, offset 32 > cpu 9 using vcpu_info at ffff8801c83d0020 > trying to map vcpu_info 10 at ffff8800329b3020, mfn 1529b3, offset 32 > cpu 10 using vcpu_info at ffff8800329b3020 > trying to map vcpu_info 11 at ffff8801c85ae020, mfn 2e85ae, offset 32 > cpu 11 using vcpu_info at ffff8801c85ae020 > trying to map vcpu_info 12 at ffff880032b91020, mfn 152b91, offset 32 > cpu 12 using vcpu_info at ffff880032b91020 > trying to map vcpu_info 13 at ffff8801c878c020, mfn 2e878c, offset 32 > cpu 13 using vcpu_info at ffff8801c878c020 > trying to map vcpu_info 14 at ffff880032d6f020, mfn 152d6f, offset 32 > cpu 14 using vcpu_info at ffff880032d6f020 > trying to map vcpu_info 15 at ffff8801c896a020, mfn 2e896a, offset 32 > cpu 15 using vcpu_info at ffff8801c896a020 > Xen: using vcpu_info placement > Built 2 zonelists in Zone order, mobility grouping on. Total pages: > 2724338 > Policy zone: Normal > Kernel command line: root=/dev/mapper/MISC-fedora ro nomodeset > console=hvc0 earlyprintk=xen debug initcall_debug loglvel=10 > PID hash table entries: 4096 (order: 3, 32768 bytes) > Initializing CPU#0 > DMA: Placing 64MB software IO TLB between ffff880020000000 - > ffff880024000000 > DMA: software IO TLB at phys 0x20000000 - 0x24000000 > xen_swiotlb_fixup: buf=ffff880020000000 size=67108864 > xen_swiotlb_fixup: buf=ffff880024060000 size=32768 > Memory: 10546768k/12272444k available (4727k kernel code, 1057880k > absent, 667796k reserved, 3359k data, 3380k init) > SLUB: Genslabs=14, HWalign=64, Order=0-3, MinObjects=0, CPUs=16, Nodes=3 > Hierarchical RCU implementation. > NR_IRQS:4352 nr_irqs:4352 > xen: --> irq=0 > xen: --> irq=1 > xen: --> irq=2 > xen: --> irq=3 > xen: --> irq=4 > xen: --> irq=5 > xen: --> irq=6 > xen: --> irq=7 > xen: --> irq=8 > xen: --> irq=9 > xen: --> irq=10 > xen: --> irq=11 > xen: --> irq=12 > xen: --> irq=13 > xen: --> irq=14 > xen: --> irq=15 > ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl) > ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 20 low level) > xen: sci override: source_irq=9 global_irq=20 trigger=c polarity=3 > xen: registering gsi 20 triggering 0 polarity 1 > alloc irq_desc for 20 on node 0 > alloc kstat_irqs on node 0 > xen: --> irq=20 > xen: acpi sci 20 > Console: colour VGA+ 80x25 > console [hvc0] enabled, bootconsole disabled > console [hvc0] enabled, bootconsole disabled > Lock dependency validator: Copyright (c) 2006 Red Hat, Inc., Ingo Molnar > ... MAX_LOCKDEP_SUBCLASSES: 8 > ... MAX_LOCK_DEPTH: 48 > ... MAX_LOCKDEP_KEYS: 8191 > ... CLASSHASH_SIZE: 4096 > ... MAX_LOCKDEP_ENTRIES: 16384 > ... MAX_LOCKDEP_CHAINS: 32768 > ... CHAINHASH_SIZE: 16384 > memory used by lock dependency info: 6367 kB > per task-struct memory footprint: 2688 bytes > allocated 112721920 bytes of page_cgroup > please try ''cgroup_disable=memory'' option if you don''t want memory > cgroups > ODEBUG: 24 of 24 active objects replaced > Xen: using vcpuop timer interface > installing Xen timer for CPU 0 > alloc irq_desc for 4351 on node 0 > alloc kstat_irqs on node 0 > Detected 2266.784 MHz processor. > Calibrating delay loop (skipped), value calculated using timer > frequency.. 4533.56 BogoMIPS (lpj=2266784) > Security Framework initialized > SELinux: Initializing. > SELinux: Starting in permissive mode > Dentry cache hash table entries: 2097152 (order: 12, 16777216 bytes) > Inode-cache hash table entries: 1048576 (order: 11, 8388608 bytes) > Mount-cache hash table entries: 256 > Initializing cgroup subsys ns > Initializing cgroup subsys cpuacct > Initializing cgroup subsys memory > Initializing cgroup subsys devices > Initializing cgroup subsys freezer > Initializing cgroup subsys net_cls > CPU: L1 I cache: 32K, L1 D cache: 32K > CPU: L2 cache: 256K > CPU: L3 cache: 8192K > CPU 0/0x0 -> Node 0 > CPU: Physical Processor ID: 0 > CPU: Processor Core ID: 0 > mce: CPU supports 9 MCE banks > Performance Events: unsupported p6 CPU model 26 no PMU driver, software > events only. > lockdep: fixing up alternatives. > SMP alternatives: switching to UP code > ACPI: Core revision 20090903 > ftrace: converting mcount calls to 0f 1f 44 00 00 > ftrace: allocating 22950 entries in 91 pages > alloc irq_desc for 4350 on node 0 > alloc kstat_irqs on node 0 > alloc irq_desc for 4349 on node 0 > alloc kstat_irqs on node 0 > alloc irq_desc for 4348 on node 0 > alloc kstat_irqs on node 0 > alloc irq_desc for 4347 on node 0 > alloc kstat_irqs on node 0 > calling migration_init+0x0/0x59 @ 1 > initcall migration_init+0x0/0x59 returned 0 after 976 usecs > calling spawn_ksoftirqd+0x0/0x5a @ 1 > initcall spawn_ksoftirqd+0x0/0x5a returned 0 after 976 usecs > calling init_call_single_data+0x0/0xad @ 1 > initcall init_call_single_data+0x0/0xad returned 0 after 0 usecs > calling spawn_softlockup_task+0x0/0x75 @ 1 > initcall spawn_softlockup_task+0x0/0x75 returned 0 after 976 usecs > calling relay_init+0x0/0x14 @ 1 > initcall relay_init+0x0/0x14 returned 0 after 0 usecs > calling tracer_alloc_buffers+0x0/0x218 @ 1 > initcall tracer_alloc_buffers+0x0/0x218 returned 0 after 976 usecs > calling init_trace_printk+0x0/0x12 @ 1 > initcall init_trace_printk+0x0/0x12 returned 0 after 0 usecs > calling trace_workqueue_early_init+0x0/0x137 @ 1 > initcall trace_workqueue_early_init+0x0/0x137 returned 0 after 976 usecs > calling mce_amd_init+0x0/0x33 @ 1 > initcall mce_amd_init+0x0/0x33 returned 0 after 0 usecs > installing Xen timer for CPU 1 > alloc irq_desc for 4346 on node 0 > alloc kstat_irqs on node 0 > lockdep: fixing up alternatives. > SMP alternatives: switching to SMP code > alloc irq_desc for 4345 on node 0 > alloc kstat_irqs on node 0 > alloc irq_desc for 4344 on node 0 > alloc kstat_irqs on node 0 > alloc irq_desc for 4343 on node 0 > alloc kstat_irqs on node 0 > alloc irq_desc for 4342 on node 0 > alloc kstat_irqs on node 0 > Initializing CPU#1 > CPU: L1 I cache: 32K, L1 D cache: 32K > CPU: L2 cache: 256K > CPU: L3 cache: 8192K > CPU 1/0x0 -> Node 0 > CPU: Physical Processor ID: 1 > CPU: Processor Core ID: 0 > installing Xen timer for CPU 2 > alloc irq_desc for 4341 on node 0 > alloc kstat_irqs on node 0 > alloc irq_desc for 4340 on node 0 > alloc kstat_irqs on node 0 > alloc irq_desc for 4339 on node 0 > alloc kstat_irqs on node 0 > alloc irq_desc for 4338 on node 0 > alloc kstat_irqs on node 0 > alloc irq_desc for 4337 on node 0 > alloc kstat_irqs on node 0 > Initializing CPU#2 > CPU: L1 I cache: 32K, L1 D cache: 32K > CPU: L2 cache: 256K > CPU: L3 cache: 8192K > CPU 2/0x0 -> Node 0 > CPU: Physical Processor ID: 0 > CPU: Processor Core ID: 1 > installing Xen timer for CPU 3 > alloc irq_desc for 4336 on node 0 > alloc kstat_irqs on node 0 > alloc irq_desc for 4335 on node 0 > alloc kstat_irqs on node 0 > alloc irq_desc for 4334 on node 0 > alloc kstat_irqs on node 0 > alloc irq_desc for 4333 on node 0 > alloc kstat_irqs on node 0 > alloc irq_desc for 4332 on node 0 > alloc kstat_irqs on node 0 > Initializing CPU#3 > CPU: L1 I cache: 32K, L1 D cache: 32K > CPU: L2 cache: 256K > CPU: L3 cache: 8192K > CPU 3/0x0 -> Node 0 > CPU: Physical Processor ID: 1 > CPU: Processor Core ID: 1 > installing Xen timer for CPU 4 > alloc irq_desc for 4331 on node 0 > alloc kstat_irqs on node 0 > alloc irq_desc for 4330 on node 0 > alloc kstat_irqs on node 0 > alloc irq_desc for 4329 on node 0 > alloc kstat_irqs on node 0 > alloc irq_desc for 4328 on node 0 > alloc kstat_irqs on node 0 > alloc irq_desc for 4327 on node 0 > alloc kstat_irqs on node 0 > Initializing CPU#4 > CPU: L1 I cache: 32K, L1 D cache: 32K > CPU: L2 cache: 256K > CPU: L3 cache: 8192K > CPU 4/0x0 -> Node 0 > CPU: Physical Processor ID: 0 > CPU: Processor Core ID: 2 > installing Xen timer for CPU 5 > alloc irq_desc for 4326 on node 0 > alloc kstat_irqs on node 0 > alloc irq_desc for 4325 on node 0 > alloc kstat_irqs on node 0 > alloc irq_desc for 4324 on node 0 > alloc kstat_irqs on node 0 > alloc irq_desc for 4323 on node 0 > alloc kstat_irqs on node 0 > alloc irq_desc for 4322 on node 0 > alloc kstat_irqs on node 0 > Initializing CPU#5 > CPU: L1 I cache: 32K, L1 D cache: 32K > CPU: L2 cache: 256K > CPU: L3 cache: 8192K > CPU 5/0x0 -> Node 0 > CPU: Physical Processor ID: 1 > CPU: Processor Core ID: 2 > installing Xen timer for CPU 6 > alloc irq_desc for 4321 on node 0 > alloc kstat_irqs on node 0 > alloc irq_desc for 4320 on node 0 > alloc kstat_irqs on node 0 > alloc irq_desc for 4319 on node 0 > alloc kstat_irqs on node 0 > alloc irq_desc for 4318 on node 0 > alloc kstat_irqs on node 0 > alloc irq_desc for 4317 on node 0 > alloc kstat_irqs on node 0 > Initializing CPU#6 > CPU: L1 I cache: 32K, L1 D cache: 32K > CPU: L2 cache: 256K > CPU: L3 cache: 8192K > CPU 6/0x0 -> Node 0 > CPU: Physical Processor ID: 0 > CPU: Processor Core ID: 3 > installing Xen timer for CPU 7 > alloc irq_desc for 4316 on node 0 > alloc kstat_irqs on node 0 > alloc irq_desc for 4315 on node 0 > alloc kstat_irqs on node 0 > alloc irq_desc for 4314 on node 0 > alloc kstat_irqs on node 0 > alloc irq_desc for 4313 on node 0 > alloc kstat_irqs on node 0 > alloc irq_desc for 4312 on node 0 > alloc kstat_irqs on node 0 > Initializing CPU#7 > CPU: L1 I cache: 32K, L1 D cache: 32K > CPU: L2 cache: 256K > CPU: L3 cache: 8192K > CPU 7/0x0 -> Node 0 > CPU: Physical Processor ID: 1 > CPU: Processor Core ID: 3 > installing Xen timer for CPU 8 > alloc irq_desc for 4311 on node 0 > alloc kstat_irqs on node 0 > alloc irq_desc for 4310 on node 0 > alloc kstat_irqs on node 0 > alloc irq_desc for 4309 on node 0 > alloc kstat_irqs on node 0 > alloc irq_desc for 4308 on node 0 > alloc kstat_irqs on node 0 > alloc irq_desc for 4307 on node 0 > alloc kstat_irqs on node 0 > Initializing CPU#8 > CPU: L1 I cache: 32K, L1 D cache: 32K > CPU: L2 cache: 256K > CPU: L3 cache: 8192K > CPU 8/0x0 -> Node 0 > CPU: Physical Processor ID: 0 > CPU: Processor Core ID: 0 > installing Xen timer for CPU 9 > alloc irq_desc for 4306 on node 0 > alloc kstat_irqs on node 0 > alloc irq_desc for 4305 on node 0 > alloc kstat_irqs on node 0 > alloc irq_desc for 4304 on node 0 > alloc kstat_irqs on node 0 > alloc irq_desc for 4303 on node 0 > alloc kstat_irqs on node 0 > alloc irq_desc for 4302 on node 0 > alloc kstat_irqs on node 0 > Initializing CPU#9 > CPU: L1 I cache: 32K, L1 D cache: 32K > CPU: L2 cache: 256K > CPU: L3 cache: 8192K > CPU 9/0x0 -> Node 0 > CPU: Physical Processor ID: 1 > CPU: Processor Core ID: 0 > installing Xen timer for CPU 10 > alloc irq_desc for 4301 on node 0 > alloc kstat_irqs on node 0 > alloc irq_desc for 4300 on node 0 > alloc kstat_irqs on node 0 > alloc irq_desc for 4299 on node 0 > alloc kstat_irqs on node 0 > alloc irq_desc for 4298 on node 0 > alloc kstat_irqs on node 0 > alloc irq_desc for 4297 on node 0 > alloc kstat_irqs on node 0 > Initializing CPU#10 > CPU: L1 I cache: 32K, L1 D cache: 32K > CPU: L2 cache: 256K > CPU: L3 cache: 8192K > CPU 10/0x0 -> Node 0 > CPU: Physical Processor ID: 0 > CPU: Processor Core ID: 1 > installing Xen timer for CPU 11 > alloc irq_desc for 4296 on node 0 > alloc kstat_irqs on node 0 > alloc irq_desc for 4295 on node 0 > alloc kstat_irqs on node 0 > alloc irq_desc for 4294 on node 0 > alloc kstat_irqs on node 0 > alloc irq_desc for 4293 on node 0 > alloc kstat_irqs on node 0 > alloc irq_desc for 4292 on node 0 > alloc kstat_irqs on node 0 > Initializing CPU#11 > CPU: L1 I cache: 32K, L1 D cache: 32K > CPU: L2 cache: 256K > CPU: L3 cache: 8192K > CPU 11/0x0 -> Node 0 > CPU: Physical Processor ID: 1 > CPU: Processor Core ID: 1 > installing Xen timer for CPU 12 > alloc irq_desc for 4291 on node 0 > alloc kstat_irqs on node 0 > alloc irq_desc for 4290 on node 0 > alloc kstat_irqs on node 0 > alloc irq_desc for 4289 on node 0 > alloc kstat_irqs on node 0 > alloc irq_desc for 4288 on node 0 > alloc kstat_irqs on node 0 > alloc irq_desc for 4287 on node 0 > alloc kstat_irqs on node 0 > Initializing CPU#12 > CPU: L1 I cache: 32K, L1 D cache: 32K > CPU: L2 cache: 256K > CPU: L3 cache: 8192K > CPU 12/0x0 -> Node 0 > CPU: Physical Processor ID: 0 > CPU: Processor Core ID: 2 > installing Xen timer for CPU 13 > alloc irq_desc for 4286 on node 0 > alloc kstat_irqs on node 0 > alloc irq_desc for 4285 on node 0 > alloc kstat_irqs on node 0 > alloc irq_desc for 4284 on node 0 > alloc kstat_irqs on node 0 > alloc irq_desc for 4283 on node 0 > alloc kstat_irqs on node 0 > alloc irq_desc for 4282 on node 0 > alloc kstat_irqs on node 0 > Initializing CPU#13 > CPU: L1 I cache: 32K, L1 D cache: 32K > CPU: L2 cache: 256K > CPU: L3 cache: 8192K > CPU 13/0x0 -> Node 0 > CPU: Physical Processor ID: 1 > CPU: Processor Core ID: 2 > installing Xen timer for CPU 14 > alloc irq_desc for 4281 on node 0 > alloc kstat_irqs on node 0 > alloc irq_desc for 4280 on node 0 > alloc kstat_irqs on node 0 > alloc irq_desc for 4279 on node 0 > alloc kstat_irqs on node 0 > alloc irq_desc for 4278 on node 0 > alloc kstat_irqs on node 0 > alloc irq_desc for 4277 on node 0 > alloc kstat_irqs on node 0 > Initializing CPU#14 > CPU: L1 I cache: 32K, L1 D cache: 32K > CPU: L2 cache: 256K > CPU: L3 cache: 8192K > CPU 14/0x0 -> Node 0 > CPU: Physical Processor ID: 0 > CPU: Processor Core ID: 3 > installing Xen timer for CPU 15 > alloc irq_desc for 4276 on node 0 > alloc kstat_irqs on node 0 > alloc irq_desc for 4275 on node 0 > alloc kstat_irqs on node 0 > alloc irq_desc for 4274 on node 0 > alloc kstat_irqs on node 0 > alloc irq_desc for 4273 on node 0 > alloc kstat_irqs on node 0 > alloc irq_desc for 4272 on node 0 > alloc kstat_irqs on node 0 > Initializing CPU#15 > CPU: L1 I cache: 32K, L1 D cache: 32K > CPU: L2 cache: 256K > CPU: L3 cache: 8192K > CPU 15/0x0 -> Node 0 > CPU: Physical Processor ID: 1 > CPU: Processor Core ID: 3 > Brought up 16 CPUs > CPU0 attaching sched-domain: > domain 0: span 0,8 level SIBLING > groups: 0 (cpu_power = 589) 8 (cpu_power = 589) > domain 1: span 0,8 level MC > groups: 0,8 (cpu_power = 1178) > domain 2: span 0-15 level CPU > groups: 0,8 (cpu_power = 1178) 1,9 (cpu_power = 1178) 2,10 > (cpu_power = 1178) 3,11 (cpu_power = 1178) 4,12 (cpu_power = 1178) 5,13 > (cpu_power = 1178) 6,14 (cpu_power = 1178) 7,15 (cpu_power = 1178) > domain 3: span 0-15 level NODE > groups: 0-15 (cpu_power = 9424) > CPU1 attaching sched-domain: > domain 0: span 1,9 level SIBLING > groups: 1 (cpu_power = 589) 9 (cpu_power = 589) > domain 1: span 1,9 level MC > groups: 1,9 (cpu_power = 1178) > domain 2: span 0-15 level CPU > groups: 1,9 (cpu_power = 1178) 2,10 (cpu_power = 1178) 3,11 > (cpu_power = 1178) 4,12 (cpu_power = 1178) 5,13 (cpu_power = 1178) 6,14 > (cpu_power = 1178) 7,15 (cpu_power = 1178) 0,8 (cpu_power = 1178) > domain 3: span 0-15 level NODE > groups: 0-15 (cpu_power = 9424) > CPU2 attaching sched-domain: > domain 0: span 2,10 level SIBLING > groups: 2 (cpu_power = 589) 10 (cpu_power = 589) > domain 1: span 2,10 level MC > groups: 2,10 (cpu_power = 1178) > domain 2: span 0-15 level CPU > groups: 2,10 (cpu_power = 1178) 3,11 (cpu_power = 1178) 4,12 > (cpu_power = 1178) 5,13 (cpu_power = 1178) 6,14 (cpu_power = 1178) 7,15 > (cpu_power = 1178) 0,8 (cpu_power = 1178) 1,9 (cpu_power = 1178) > domain 3: span 0-15 level NODE > groups: 0-15 (cpu_power = 9424) > CPU3 attaching sched-domain: > domain 0: span 3,11 level SIBLING > groups: 3 (cpu_power = 589) 11 (cpu_power = 589) > domain 1: span 3,11 level MC > groups: 3,11 (cpu_power = 1178) > domain 2: span 0-15 level CPU > groups: 3,11 (cpu_power = 1178) 4,12 (cpu_power = 1178) 5,13 > (cpu_power = 1178) 6,14 (cpu_power = 1178) 7,15 (cpu_power = 1178) 0,8 > (cpu_power = 1178) 1,9 (cpu_power = 1178) 2,10 (cpu_power = 1178) > domain 3: span 0-15 level NODE > groups: 0-15 (cpu_power = 9424) > CPU4 attaching sched-domain: > domain 0: span 4,12 level SIBLING > groups: 4 (cpu_power = 589) 12 (cpu_power = 589) > domain 1: span 4,12 level MC > groups: 4,12 (cpu_power = 1178) > domain 2: span 0-15 level CPU > groups: 4,12 (cpu_power = 1178) 5,13 (cpu_power = 1178) 6,14 > (cpu_power = 1178) 7,15 (cpu_power = 1178) 0,8 (cpu_power = 1178) 1,9 > (cpu_power = 1178) 2,10 (cpu_power = 1178) 3,11 (cpu_power = 1178) > domain 3: span 0-15 level NODE > groups: 0-15 (cpu_power = 9424) > CPU5 attaching sched-domain: > domain 0: span 5,13 level SIBLING > groups: 5 (cpu_power = 589) 13 (cpu_power = 589) > domain 1: span 5,13 level MC > groups: 5,13 (cpu_power = 1178) > domain 2: span 0-15 level CPU > groups: 5,13 (cpu_power = 1178) 6,14 (cpu_power = 1178) 7,15 > (cpu_power = 1178) 0,8 (cpu_power = 1178) 1,9 (cpu_power = 1178) 2,10 > (cpu_power = 1178) 3,11 (cpu_power = 1178) 4,12 (cpu_power = 1178) > domain 3: span 0-15 level NODE > groups: 0-15 (cpu_power = 9424) > CPU6 attaching sched-domain: > domain 0: span 6,14 level SIBLING > groups: 6 (cpu_power = 589) 14 (cpu_power = 589) > domain 1: span 6,14 level MC > groups: 6,14 (cpu_power = 1178) > domain 2: span 0-15 level CPU > groups: 6,14 (cpu_power = 1178) 7,15 (cpu_power = 1178) 0,8 > (cpu_power = 1178) 1,9 (cpu_power = 1178) 2,10 (cpu_power = 1178) 3,11 > (cpu_power = 1178) 4,12 (cpu_power = 1178) 5,13 (cpu_power = 1178) > domain 3: span 0-15 level NODE > groups: 0-15 (cpu_power = 9424) > CPU7 attaching sched-domain: > domain 0: span 7,15 level SIBLING > groups: 7 (cpu_power = 589) 15 (cpu_power = 589) > domain 1: span 7,15 level MC > groups: 7,15 (cpu_power = 1178) > domain 2: span 0-15 level CPU > groups: 7,15 (cpu_power = 1178) 0,8 (cpu_power = 1178) 1,9 > (cpu_power = 1178) 2,10 (cpu_power = 1178) 3,11 (cpu_power = 1178) 4,12 > (cpu_power = 1178) 5,13 (cpu_power = 1178) 6,14 (cpu_power = 1178) > domain 3: span 0-15 level NODE > groups: 0-15 (cpu_power = 9424) > CPU8 attaching sched-domain: > domain 0: span 0,8 level SIBLING > groups: 8 (cpu_power = 589) 0 (cpu_power = 589) > domain 1: span 0,8 level MC > groups: 0,8 (cpu_power = 1178) > domain 2: span 0-15 level CPU > groups: 0,8 (cpu_power = 1178) 1,9 (cpu_power = 1178) 2,10 > (cpu_power = 1178) 3,11 (cpu_power = 1178) 4,12 (cpu_power = 1178) 5,13 > (cpu_power = 1178) 6,14 (cpu_power = 1178) 7,15 (cpu_power = 1178) > domain 3: span 0-15 level NODE > groups: 0-15 (cpu_power = 9424) > CPU9 attaching sched-domain: > domain 0: span 1,9 level SIBLING > groups: 9 (cpu_power = 589) 1 (cpu_power = 589) > domain 1: span 1,9 level MC > groups: 1,9 (cpu_power = 1178) > domain 2: span 0-15 level CPU > groups: 1,9 (cpu_power = 1178) 2,10 (cpu_power = 1178) 3,11 > (cpu_power = 1178) 4,12 (cpu_power = 1178) 5,13 (cpu_power = 1178) 6,14 > (cpu_power = 1178) 7,15 (cpu_power = 1178) 0,8 (cpu_power = 1178) > domain 3: span 0-15 level NODE > groups: 0-15 (cpu_power = 9424) > CPU10 attaching sched-domain: > domain 0: span 2,10 level SIBLING > groups: 10 (cpu_power = 589) 2 (cpu_power = 589) > domain 1: span 2,10 level MC > groups: 2,10 (cpu_power = 1178) > domain 2: span 0-15 level CPU > groups: 2,10 (cpu_power = 1178) 3,11 (cpu_power = 1178) 4,12 > (cpu_power = 1178) 5,13 (cpu_power = 1178) 6,14 (cpu_power = 1178) 7,15 > (cpu_power = 1178) 0,8 (cpu_power = 1178) 1,9 (cpu_power = 1178) > domain 3: span 0-15 level NODE > groups: 0-15 (cpu_power = 9424) > CPU11 attaching sched-domain: > domain 0: span 3,11 level SIBLING > groups: 11 (cpu_power = 589) 3 (cpu_power = 589) > domain 1: span 3,11 level MC > groups: 3,11 (cpu_power = 1178) > domain 2: span 0-15 level CPU > groups: 3,11 (cpu_power = 1178) 4,12 (cpu_power = 1178) 5,13 > (cpu_power = 1178) 6,14 (cpu_power = 1178) 7,15 (cpu_power = 1178) 0,8 > (cpu_power = 1178) 1,9 (cpu_power = 1178) 2,10 (cpu_power = 1178) > domain 3: span 0-15 level NODE > groups: 0-15 (cpu_power = 9424) > CPU12 attaching sched-domain: > domain 0: span 4,12 level SIBLING > groups: 12 (cpu_power = 589) 4 (cpu_power = 589) > domain 1: span 4,12 level MC > groups: 4,12 (cpu_power = 1178) > domain 2: span 0-15 level CPU > groups: 4,12 (cpu_power = 1178) 5,13 (cpu_power = 1178) 6,14 > (cpu_power = 1178) 7,15 (cpu_power = 1178) 0,8 (cpu_power = 1178) 1,9 > (cpu_power = 1178) 2,10 (cpu_power = 1178) 3,11 (cpu_power = 1178) > domain 3: span 0-15 level NODE > groups: 0-15 (cpu_power = 9424) > CPU13 attaching sched-domain: > domain 0: span 5,13 level SIBLING > groups: 13 (cpu_power = 589) 5 (cpu_power = 589) > domain 1: span 5,13 level MC > groups: 5,13 (cpu_power = 1178) > domain 2: span 0-15 level CPU > groups: 5,13 (cpu_power = 1178) 6,14 (cpu_power = 1178) 7,15 > (cpu_power = 1178) 0,8 (cpu_power = 1178) 1,9 (cpu_power = 1178) 2,10 > (cpu_power = 1178) 3,11 (cpu_power = 1178) 4,12 (cpu_power = 1178) > domain 3: span 0-15 level NODE > groups: 0-15 (cpu_power = 9424) > CPU14 attaching sched-domain: > domain 0: span 6,14 level SIBLING > groups: 14 (cpu_power = 589) 6 (cpu_power = 589) > domain 1: span 6,14 level MC > groups: 6,14 (cpu_power = 1178) > domain 2: span 0-15 level CPU > groups: 6,14 (cpu_power = 1178) 7,15 (cpu_power = 1178) 0,8 > (cpu_power = 1178) 1,9 (cpu_power = 1178) 2,10 (cpu_power = 1178) 3,11 > (cpu_power = 1178) 4,12 (cpu_power = 1178) 5,13 (cpu_power = 1178) > domain 3: span 0-15 level NODE > groups: 0-15 (cpu_power = 9424) > CPU15 attaching sched-domain: > domain 0: span 7,15 level SIBLING > groups: 15 (cpu_power = 589) 7 (cpu_power = 589) > domain 1: span 7,15 level MC > groups: 7,15 (cpu_power = 1178) > domain 2: span 0-15 level CPU > groups: 7,15 (cpu_power = 1178) 0,8 (cpu_power = 1178) 1,9 > (cpu_power = 1178) 2,10 (cpu_power = 1178) 3,11 (cpu_power = 1178) 4,12 > (cpu_power = 1178) 5,13 (cpu_power = 1178) 6,14 (cpu_power = 1178) > domain 3: span 0-15 level NODE > groups: 0-15 (cpu_power = 9424) > calling init_mmap_min_addr+0x0/0x26 @ 1 > initcall init_mmap_min_addr+0x0/0x26 returned 0 after 0 usecs > calling init_cpufreq_transition_notifier_list+0x0/0x1b @ 1 > initcall init_cpufreq_transition_notifier_list+0x0/0x1b returned 0 after > 0 usecs > calling net_ns_init+0x0/0xf8 @ 1 > initcall net_ns_init+0x0/0xf8 returned 0 after 976 usecs > calling e820_mark_nvs_memory+0x0/0x40 @ 1 > initcall e820_mark_nvs_memory+0x0/0x40 returned 0 after 976 usecs > calling cpufreq_tsc+0x0/0x28 @ 1 > initcall cpufreq_tsc+0x0/0x28 returned 0 after 0 usecs > calling pci_reboot_init+0x0/0x14 @ 1 > initcall pci_reboot_init+0x0/0x14 returned 0 after 0 usecs > calling init_lapic_sysfs+0x0/0x2d @ 1 > initcall init_lapic_sysfs+0x0/0x2d returned 0 after 0 usecs > calling alloc_frozen_cpus+0x0/0xd @ 1 > initcall alloc_frozen_cpus+0x0/0xd returned 0 after 0 usecs > calling sysctl_init+0x0/0x32 @ 1 > initcall sysctl_init+0x0/0x32 returned 0 after 976 usecs > calling ksysfs_init+0x0/0xbb @ 1 > initcall ksysfs_init+0x0/0xbb returned 0 after 0 usecs > calling async_init+0x0/0x60 @ 1 > initcall async_init+0x0/0x60 returned 0 after 976 usecs > calling init_jiffies_clocksource+0x0/0x12 @ 1 > initcall init_jiffies_clocksource+0x0/0x12 returned 0 after 0 usecs > calling pm_init+0x0/0x34 @ 1 > initcall pm_init+0x0/0x34 returned 0 after 0 usecs > calling pm_disk_init+0x0/0x19 @ 1 > initcall pm_disk_init+0x0/0x19 returned 0 after 0 usecs > calling swsusp_header_init+0x0/0x31 @ 1 > initcall swsusp_header_init+0x0/0x31 returned 0 after 0 usecs > calling init_zero_pfn+0x0/0x35 @ 1 > initcall init_zero_pfn+0x0/0x35 returned 0 after 0 usecs > calling filelock_init+0x0/0x2e @ 1 > initcall filelock_init+0x0/0x2e returned 0 after 976 usecs > calling init_misc_binfmt+0x0/0x42 @ 1 > initcall init_misc_binfmt+0x0/0x42 returned 0 after 0 usecs > calling init_script_binfmt+0x0/0x14 @ 1 > initcall init_script_binfmt+0x0/0x14 returned 0 after 0 usecs > calling init_elf_binfmt+0x0/0x14 @ 1 > initcall init_elf_binfmt+0x0/0x14 returned 0 after 0 usecs > calling init_compat_elf_binfmt+0x0/0x14 @ 1 > initcall init_compat_elf_binfmt+0x0/0x14 returned 0 after 0 usecs > calling debugfs_init+0x0/0x5a @ 1 > initcall debugfs_init+0x0/0x5a returned 0 after 0 usecs > calling securityfs_init+0x0/0x51 @ 1 > initcall securityfs_init+0x0/0x51 returned 0 after 0 usecs > calling random32_init+0x0/0xd7 @ 1 > initcall random32_init+0x0/0xd7 returned 0 after 0 usecs > calling __gnttab_init+0x0/0x26 @ 1 > Grant table initialized > initcall __gnttab_init+0x0/0x26 returned 0 after 976 usecs > calling regulator_init+0x0/0x2e @ 1 > regulator: core version 0.5 > initcall regulator_init+0x0/0x2e returned 0 after 0 usecs > calling early_resume_init+0x0/0x19d @ 1 > Time: 11:17:44 Date: 05/30/10 > initcall early_resume_init+0x0/0x19d returned 0 after 0 usecs > calling cpufreq_core_init+0x0/0xa2 @ 1 > initcall cpufreq_core_init+0x0/0xa2 returned 0 after 0 usecs > calling cpuidle_init+0x0/0x40 @ 1 > initcall cpuidle_init+0x0/0x40 returned 0 after 976 usecs > calling sock_init+0x0/0x5e @ 1 > initcall sock_init+0x0/0x5e returned 0 after 976 usecs > calling net_inuse_init+0x0/0x26 @ 1 > initcall net_inuse_init+0x0/0x26 returned 0 after 0 usecs > calling netpoll_init+0x0/0x41 @ 1 > initcall netpoll_init+0x0/0x41 returned 0 after 0 usecs > calling netlink_proto_init+0x0/0x142 @ 1 > NET: Registered protocol family 16 > initcall netlink_proto_init+0x0/0x142 returned 0 after 976 usecs > calling bdi_class_init+0x0/0x41 @ 1 > initcall bdi_class_init+0x0/0x41 returned 0 after 976 usecs > calling kobject_uevent_init+0x0/0x54 @ 1 > initcall kobject_uevent_init+0x0/0x54 returned 0 after 976 usecs > calling pcibus_class_init+0x0/0x19 @ 1 > initcall pcibus_class_init+0x0/0x19 returned 0 after 976 usecs > calling pci_driver_init+0x0/0x12 @ 1 > initcall pci_driver_init+0x0/0x12 returned 0 after 976 usecs > calling backlight_class_init+0x0/0x5d @ 1 > initcall backlight_class_init+0x0/0x5d returned 0 after 0 usecs > calling __xenbus_probe_init+0x0/0x21 @ 1 > alloc irq_desc for 4271 on node 0 > alloc kstat_irqs on node 0 > initcall __xenbus_probe_init+0x0/0x21 returned 0 after 1952 usecs > calling tty_class_init+0x0/0x38 @ 1 > initcall tty_class_init+0x0/0x38 returned 0 after 0 usecs > calling vtconsole_class_init+0x0/0xc3 @ 1 > initcall vtconsole_class_init+0x0/0xc3 returned 0 after 976 usecs > calling register_node_type+0x0/0x7e @ 1 > initcall register_node_type+0x0/0x7e returned 0 after 976 usecs > calling amd_postcore_init+0x0/0x78 @ 1 > initcall amd_postcore_init+0x0/0x78 returned 0 after 0 usecs > calling arch_kdebugfs_init+0x0/0x272 @ 1 > initcall arch_kdebugfs_init+0x0/0x272 returned 0 after 0 usecs > calling mtrr_if_init+0x0/0x63 @ 1 > initcall mtrr_if_init+0x0/0x63 returned 0 after 0 usecs > calling ffh_cstate_init+0x0/0x2a @ 1 > initcall ffh_cstate_init+0x0/0x2a returned 0 after 0 usecs > calling arch_init_ftrace_syscalls+0x0/0x11e @ 1 > initcall arch_init_ftrace_syscalls+0x0/0x11e returned 0 after 976 usecs > calling acpi_pci_init+0x0/0x5c @ 1 > ACPI: bus type pci registered > initcall acpi_pci_init+0x0/0x5c returned 0 after 0 usecs > calling register_xen_pci_notifier+0x0/0x24 @ 1 > initcall register_xen_pci_notifier+0x0/0x24 returned 0 after 0 usecs > calling setup_vcpu_hotplug_event+0x0/0x22 @ 1 > initcall setup_vcpu_hotplug_event+0x0/0x22 returned 0 after 0 usecs > calling dmi_id_init+0x0/0x34c @ 1 > initcall dmi_id_init+0x0/0x34c returned 0 after 976 usecs > calling dma_bus_init+0x0/0x3f @ 1 > initcall dma_bus_init+0x0/0x3f returned 0 after 0 usecs > calling dma_channel_table_init+0x0/0x10e @ 1 > initcall dma_channel_table_init+0x0/0x10e returned 0 after 0 usecs > calling pci_arch_init+0x0/0x60 @ 1 > PCI: MCFG configuration 0: base e0000000 segment 0 buses 0 - 255 > PCI: Not using MMCONFIG. > PCI: Using configuration type 1 for base access > initcall pci_arch_init+0x0/0x60 returned 0 after 0 usecs > calling topology_init+0x0/0x97 @ 1 > initcall topology_init+0x0/0x97 returned 0 after 976 usecs > calling mtrr_init_finialize+0x0/0x3d @ 1 > initcall mtrr_init_finialize+0x0/0x3d returned 0 after 0 usecs > calling param_sysfs_init+0x0/0x23a @ 1 > initcall param_sysfs_init+0x0/0x23a returned 0 after 7811 usecs > calling pm_sysrq_init+0x0/0x1e @ 1 > initcall pm_sysrq_init+0x0/0x1e returned 0 after 0 usecs > calling audit_watch_init+0x0/0x2f @ 1 > initcall audit_watch_init+0x0/0x2f returned 0 after 0 usecs > calling init_slow_work+0x0/0x37 @ 1 > initcall init_slow_work+0x0/0x37 returned 0 after 0 usecs > calling default_bdi_init+0x0/0xc6 @ 1 > initcall default_bdi_init+0x0/0xc6 returned 0 after 976 usecs > calling init_bio+0x0/0xce @ 1 > bio: create slab <bio-0> at 0 > initcall init_bio+0x0/0xce returned 0 after 3905 usecs > calling fsnotify_init+0x0/0x12 @ 1 > initcall fsnotify_init+0x0/0x12 returned 0 after 0 usecs > calling fsnotify_notification_init+0x0/0x100 @ 1 > initcall fsnotify_notification_init+0x0/0x100 returned 0 after 976 usecs > calling cryptomgr_init+0x0/0x12 @ 1 > initcall cryptomgr_init+0x0/0x12 returned 0 after 0 usecs > calling blk_settings_init+0x0/0x2a @ 1 > initcall blk_settings_init+0x0/0x2a returned 0 after 0 usecs > calling blk_ioc_init+0x0/0x2a @ 1 > initcall blk_ioc_init+0x0/0x2a returned 0 after 0 usecs > calling blk_softirq_init+0x0/0x70 @ 1 > initcall blk_softirq_init+0x0/0x70 returned 0 after 0 usecs > calling blk_iopoll_setup+0x0/0x70 @ 1 > initcall blk_iopoll_setup+0x0/0x70 returned 0 after 0 usecs > calling genhd_device_init+0x0/0x7b @ 1 > initcall genhd_device_init+0x0/0x7b returned 0 after 2929 usecs > calling blk_dev_integrity_init+0x0/0x2a @ 1 > initcall blk_dev_integrity_init+0x0/0x2a returned 0 after 0 usecs > calling pci_slot_init+0x0/0x4c @ 1 > initcall pci_slot_init+0x0/0x4c returned 0 after 0 usecs > calling fbmem_init+0x0/0x98 @ 1 > initcall fbmem_init+0x0/0x98 returned 0 after 0 usecs > calling acpi_init+0x0/0x2d1 @ 1 > ERROR: Unable to locate IOAPIC for GSI 20 > ACPI: EC: Look up EC in DSDT > ACPI Warning for \_SB_._OSC: Return type mismatch - found Integer, > expected Buffer (20090903/nspredef-1006) > \_SB_:_OSC evaluation returned wrong type > _OSC request data:1 6 > ACPI: Executed 1 blocks of module-level executable AML code > ACPI: Interpreter enabled > ACPI: (supports S0 S1 S4 S5) > ACPI: Using IOAPIC for interrupt routing > PCI: MCFG configuration 0: base e0000000 segment 0 buses 0 - 255 > PCI: MCFG area at e0000000 reserved in ACPI motherboard resources > PCI: Using MMCONFIG at e0000000 - efffffff > ACPI Warning: Incorrect checksum in table [OEMB] - 54, should be 51 > (20090903/tbutils-314) > ACPI Warning: Incorrect checksum in table [ ] - 50, should be 94 > (20090903/tbutils-314) > initcall acpi_init+0x0/0x2d1 returned 0 after 158183 usecs > calling dock_init+0x0/0x8d @ 1 > ACPI: No dock devices found. > initcall dock_init+0x0/0x8d returned 0 after 0 usecs > calling acpi_pci_root_init+0x0/0x28 @ 1 > ACPI: PCI Root Bridge [PCI0] (0000:00) > pci 0000:00:00.0: PME# supported from D0 D3hot D3cold > pci 0000:00:00.0: PME# disabled > pci 0000:00:01.0: PME# supported from D0 D3hot D3cold > pci 0000:00:01.0: PME# disabled > pci 0000:00:03.0: PME# supported from D0 D3hot D3cold > pci 0000:00:03.0: PME# disabled > pci 0000:00:07.0: PME# supported from D0 D3hot D3cold > pci 0000:00:07.0: PME# disabled > pci 0000:00:16.0: reg 10 64bit mmio: [0xfbbfc000-0xfbbfffff] > pci 0000:00:16.1: reg 10 64bit mmio: [0xfbbf8000-0xfbbfbfff] > pci 0000:00:16.2: reg 10 64bit mmio: [0xfbbf4000-0xfbbf7fff] > pci 0000:00:16.3: reg 10 64bit mmio: [0xfbbf0000-0xfbbf3fff] > pci 0000:00:16.4: reg 10 64bit mmio: [0xfbbec000-0xfbbeffff] > pci 0000:00:16.5: reg 10 64bit mmio: [0xfbbe8000-0xfbbebfff] > pci 0000:00:16.6: reg 10 64bit mmio: [0xfbbe4000-0xfbbe7fff] > pci 0000:00:16.7: reg 10 64bit mmio: [0xfbbe0000-0xfbbe3fff] > pci 0000:00:1a.0: reg 20 io port: [0xac00-0xac1f] > pci 0000:00:1a.1: reg 20 io port: [0xa880-0xa89f] > pci 0000:00:1a.2: reg 20 io port: [0xa800-0xa81f] > pci 0000:00:1a.7: reg 10 32bit mmio: [0xfbbde000-0xfbbde3ff] > pci 0000:00:1a.7: PME# supported from D0 D3hot D3cold > pci 0000:00:1a.7: PME# disabled > pci 0000:00:1b.0: reg 10 64bit mmio: [0xfbbd8000-0xfbbdbfff] > pci 0000:00:1b.0: PME# supported from D0 D3hot D3cold > pci 0000:00:1b.0: PME# disabled > pci 0000:00:1c.0: PME# supported from D0 D3hot D3cold > pci 0000:00:1c.0: PME# disabled > pci 0000:00:1c.4: PME# supported from D0 D3hot D3cold > pci 0000:00:1c.4: PME# disabled > pci 0000:00:1c.5: PME# supported from D0 D3hot D3cold > pci 0000:00:1c.5: PME# disabled > pci 0000:00:1d.0: reg 20 io port: [0xa480-0xa49f] > pci 0000:00:1d.1: reg 20 io port: [0xa400-0xa41f] > pci 0000:00:1d.2: reg 20 io port: [0xa080-0xa09f] > pci 0000:00:1d.7: reg 10 32bit mmio: [0xfbbdc000-0xfbbdc3ff] > pci 0000:00:1d.7: PME# supported from D0 D3hot D3cold > pci 0000:00:1d.7: PME# disabled > pci 0000:00:1f.0: quirk: region 0800-087f claimed by ICH6 ACPI/GPIO/TCO > pci 0000:00:1f.0: quirk: region 0500-053f claimed by ICH6 GPIO > pci 0000:00:1f.0: ICH7 LPC Generic IO decode 1 PIO at 0a00 (mask 00ff) > pci 0000:00:1f.0: ICH7 LPC Generic IO decode 3 PIO at 0290 (mask 0097) > pci 0000:00:1f.2: reg 10 io port: [0xa000-0xa007] > pci 0000:00:1f.2: reg 14 io port: [0x9c00-0x9c03] > pci 0000:00:1f.2: reg 18 io port: [0x9880-0x9887] > pci 0000:00:1f.2: reg 1c io port: [0x9800-0x9803] > pci 0000:00:1f.2: reg 20 io port: [0x9480-0x949f] > pci 0000:00:1f.2: reg 24 32bit mmio: [0xfbbd6000-0xfbbd67ff] > pci 0000:00:1f.2: PME# supported from D3hot > pci 0000:00:1f.2: PME# disabled > pci 0000:00:1f.3: reg 10 64bit mmio: [0xfbbd4000-0xfbbd40ff] > pci 0000:00:1f.3: reg 20 io port: [0x400-0x41f] > pci 0000:01:00.0: reg 10 32bit mmio: [0xf6000000-0xf6ffffff] > pci 0000:01:00.0: reg 14 64bit mmio pref: [0xc0000000-0xcfffffff] > pci 0000:01:00.0: reg 1c 64bit mmio: [0xf4000000-0xf5ffffff] > pci 0000:01:00.0: reg 24 io port: [0xbc00-0xbc7f] > pci 0000:01:00.0: reg 30 32bit mmio pref: [0xf3fe0000-0xf3ffffff] > pci 0000:00:01.0: bridge io port: [0xb000-0xbfff] > pci 0000:00:01.0: bridge 32bit mmio: [0xf3f00000-0xf6ffffff] > pci 0000:00:01.0: bridge 64bit mmio pref: [0xc0000000-0xcfffffff] > pci 0000:03:00.0: reg 10 32bit mmio: [0xfa000000-0xfaffffff] > pci 0000:03:00.0: reg 14 64bit mmio pref: [0xd0000000-0xdfffffff] > pci 0000:03:00.0: reg 1c 64bit mmio: [0xf8000000-0xf9ffffff] > pci 0000:03:00.0: reg 24 io port: [0xcc00-0xcc7f] > pci 0000:03:00.0: reg 30 32bit mmio pref: [0xf7fe0000-0xf7ffffff] > pci 0000:00:07.0: bridge io port: [0xc000-0xcfff] > pci 0000:00:07.0: bridge 32bit mmio: [0xf7f00000-0xfaffffff] > pci 0000:00:07.0: bridge 64bit mmio pref: [0xd0000000-0xdfffffff] > pci 0000:04:00.0: PME# supported from D0 D3hot D3cold > pci 0000:04:00.0: PME# disabled > pci 0000:04:00.2: PME# supported from D0 D3hot D3cold > pci 0000:04:00.2: PME# disabled > pci 0000:04:00.0: disabling ASPM on pre-1.1 PCIe device. You can enable > it with ''pcie_aspm=force'' > pci 0000:00:1c.0: bridge 32bit mmio: [0xfbc00000-0xfbcfffff] > pci 0000:00:1c.0: bridge 64bit mmio pref: [0xf2f00000-0xf2ffffff] > pci 0000:05:0e.0: reg 10 32bit mmio pref: [0xf2ff0000-0xf2ffffff] > pci 0000:05:0e.0: reg 18 32bit mmio: [0xfbce0000-0xfbcfffff] > pci 0000:05:0e.0: reg 30 32bit mmio pref: [0xfbcd0000-0xfbcd7fff] > pci 0000:05:0e.0: supports D1 > pci 0000:04:00.0: bridge 32bit mmio: [0xfbc00000-0xfbcfffff] > pci 0000:04:00.0: bridge 64bit mmio pref: [0xf2f00000-0xf2ffffff] > pci 0000:07:00.0: reg 10 32bit mmio: [0xfbde0000-0xfbdfffff] > pci 0000:07:00.0: reg 18 io port: [0xdc00-0xdc1f] > pci 0000:07:00.0: reg 1c 32bit mmio: [0xfbddc000-0xfbddffff] > pci 0000:07:00.0: PME# supported from D0 D3hot D3cold > pci 0000:07:00.0: PME# disabled > pci 0000:00:1c.4: bridge io port: [0xd000-0xdfff] > pci 0000:00:1c.4: bridge 32bit mmio: [0xfbd00000-0xfbdfffff] > pci 0000:08:00.0: reg 10 32bit mmio: [0xfbee0000-0xfbefffff] > pci 0000:08:00.0: reg 18 io port: [0xec00-0xec1f] > pci 0000:08:00.0: reg 1c 32bit mmio: [0xfbedc000-0xfbedffff] > pci 0000:08:00.0: PME# supported from D0 D3hot D3cold > pci 0000:08:00.0: PME# disabled > pci 0000:00:1c.5: bridge io port: [0xe000-0xefff] > pci 0000:00:1c.5: bridge 32bit mmio: [0xfbe00000-0xfbefffff] > pci 0000:00:1e.0: transparent bridge > ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT] > ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P0P1._PRT] > ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P0P4._PRT] > ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P0P8._PRT] > ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P0P9._PRT] > ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.NPE1._PRT] > ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.NPE3._PRT] > ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.NPE7._PRT] > (XEN) PCI add device 00:00.0 > (XEN) PCI add device 00:01.0 > (XEN) PCI add device 00:03.0 > (XEN) PCI add device 00:07.0 > (XEN) PCI add device 00:14.0 > (XEN) PCI add device 00:14.1 > (XEN) PCI add device 00:14.2 > (XEN) PCI add device 00:14.3 > (XEN) PCI add device 00:16.0 > (XEN) PCI add device 00:16.1 > (XEN) PCI add device 00:16.2 > (XEN) PCI add device 00:16.3 > (XEN) PCI add device 00:16.4 > (XEN) PCI add device 00:16.5 > (XEN) PCI add device 00:16.6 > (XEN) PCI add device 00:16.7 > (XEN) PCI add device 00:1a.0 > (XEN) PCI add device 00:1a.1 > (XEN) PCI add device 00:1a.2 > (XEN) PCI add device 00:1a.7 > (XEN) PCI add device 00:1b.0 > (XEN) PCI add device 00:1c.0 > (XEN) PCI add device 00:1c.4 > (XEN) PCI add device 00:1c.5 > (XEN) PCI add device 00:1d.0 > (XEN) PCI add device 00:1d.1 > (XEN) PCI add device 00:1d.2 > (XEN) PCI add device 00:1d.7 > (XEN) PCI add device 00:1e.0 > (XEN) PCI add device 00:1f.0 > (XEN) PCI add device 00:1f.2 > (XEN) PCI add device 00:1f.3 > (XEN) PCI add device 01:00.0 > (XEN) PCI add device 03:00.0 > (XEN) PCI add device 04:00.0 > (XEN) PCI add device 04:00.2 > (XEN) PCI add device 05:0e.0 > (XEN) PCI add device 07:00.0 > (XEN) PCI add device 08:00.0 > initcall acpi_pci_root_init+0x0/0x28 returned 0 after 89843 usecs > calling acpi_pci_link_init+0x0/0x43 @ 1 > ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 6 7 10 *11 12 14 15) > ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 6 7 *10 11 12 14 15) > ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 6 7 10 11 12 *14 15) > ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 6 7 10 11 12 14 *15) > ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 6 7 10 11 12 14 15) *0, > disabled. > ACPI: PCI Interrupt Link [LNKF] (IRQs 3 4 6 *7 10 11 12 14 15) > ACPI: PCI Interrupt Link [LNKG] (IRQs 3 4 *6 7 10 11 12 14 15) > ACPI: PCI Interrupt Link [LNKH] (IRQs 3 4 6 7 *10 11 12 14 15) > initcall acpi_pci_link_init+0x0/0x43 returned 0 after 4882 usecs > calling pnp_init+0x0/0x12 @ 1 > initcall pnp_init+0x0/0x12 returned 0 after 0 usecs > calling __setup_shutdown_event+0x0/0x2a @ 1 > initcall __setup_shutdown_event+0x0/0x2a returned 0 after 0 usecs > calling xen_pcpu_init+0x0/0xa7 @ 1 > sync cpu 0 get result 1 max_id f > sync cpu 1 get result 1 max_id f > sync cpu 2 get result 1 max_id f > sync cpu 3 get result 1 max_id f > sync cpu 4 get result 1 max_id f > sync cpu 5 get result 1 max_id f > sync cpu 6 get result 1 max_id f > sync cpu 7 get result 1 max_id f > sync cpu 8 get result 1 max_id f > sync cpu 9 get result 1 max_id f > sync cpu a get result 1 max_id f > sync cpu b get result 1 max_id f > sync cpu c get result 1 max_id f > sync cpu d get result 1 max_id f > sync cpu e get result 1 max_id f > sync cpu f get result 1 max_id f > alloc irq_desc for 4270 on node 0 > alloc kstat_irqs on node 0 > initcall xen_pcpu_init+0x0/0xa7 returned 4270 after 16601 usecs > initcall xen_pcpu_init+0x0/0xa7 returned with error code 4270 > calling xenbus_probe_backend_init+0x0/0x64 @ 1 > initcall xenbus_probe_backend_init+0x0/0x64 returned 0 after 976 usecs > calling xenbus_probe_frontend_init+0x0/0x64 @ 1 > initcall xenbus_probe_frontend_init+0x0/0x64 returned 0 after 0 usecs > calling balloon_init+0x0/0x208 @ 1 > xen_balloon: Initialising balloon driver with page order 0. > initcall balloon_init+0x0/0x208 returned 0 after 0 usecs > calling xen_acpi_processor_extcntl_init+0x0/0x4f @ 1 > initcall xen_acpi_processor_extcntl_init+0x0/0x4f returned 0 after 0 > usecs > calling misc_init+0x0/0xb7 @ 1 > initcall misc_init+0x0/0xb7 returned 0 after 0 usecs > calling vga_arb_device_init+0x0/0x78 @ 1 > vgaarb: device added: PCI:0000:01:00.0,decodes=io > +mem,owns=none,locks=none > vgaarb: device added: PCI:0000:03:00.0,decodes=io+mem,owns=io > +mem,locks=none > vgaarb: loaded > initcall vga_arb_device_init+0x0/0x78 returned 0 after 976 usecs > calling cn_init+0x0/0xa3 @ 1 > initcall cn_init+0x0/0xa3 returned 0 after 976 usecs > calling init_scsi+0x0/0x91 @ 1 > SCSI subsystem initialized > initcall init_scsi+0x0/0x91 returned 0 after 976 usecs > calling ata_init+0x0/0x390 @ 1 > libata version 3.00 loaded. > initcall ata_init+0x0/0x390 returned 0 after 1953 usecs > calling phy_init+0x0/0x31 @ 1 > initcall phy_init+0x0/0x31 returned 0 after 976 usecs > calling init_pcmcia_cs+0x0/0x36 @ 1 > initcall init_pcmcia_cs+0x0/0x36 returned 0 after 0 usecs > calling usb_init+0x0/0x1b2 @ 1 > usbcore: registered new interface driver usbfs > usbcore: registered new interface driver hub > usbcore: registered new device driver usb > initcall usb_init+0x0/0x1b2 returned 0 after 1953 usecs > calling serio_init+0x0/0x89 @ 1 > initcall serio_init+0x0/0x89 returned 0 after 976 usecs > calling input_init+0x0/0x13d @ 1 > initcall input_init+0x0/0x13d returned 0 after 0 usecs > calling rtc_init+0x0/0x71 @ 1 > initcall rtc_init+0x0/0x71 returned 0 after 976 usecs > calling power_supply_class_init+0x0/0x38 @ 1 > initcall power_supply_class_init+0x0/0x38 returned 0 after 0 usecs > calling thermal_init+0x0/0x58 @ 1 > initcall thermal_init+0x0/0x58 returned 0 after 0 usecs > calling md_init+0x0/0xd0 @ 1 > initcall md_init+0x0/0xd0 returned 0 after 0 usecs > calling leds_init+0x0/0x40 @ 1 > initcall leds_init+0x0/0x40 returned 0 after 0 usecs > calling pci_subsys_init+0x0/0x11a @ 1 > PCI: Using ACPI for IRQ routing > initcall pci_subsys_init+0x0/0x11a returned 0 after 0 usecs > calling proto_init+0x0/0x12 @ 1 > initcall proto_init+0x0/0x12 returned 0 after 0 usecs > calling net_dev_init+0x0/0x1a1 @ 1 > initcall net_dev_init+0x0/0x1a1 returned 0 after 976 usecs > calling neigh_init+0x0/0x71 @ 1 > initcall neigh_init+0x0/0x71 returned 0 after 0 usecs > calling fib_rules_init+0x0/0xa6 @ 1 > initcall fib_rules_init+0x0/0xa6 returned 0 after 0 usecs > calling pktsched_init+0x0/0xd0 @ 1 > initcall pktsched_init+0x0/0xd0 returned 0 after 0 usecs > calling tc_filter_init+0x0/0x4c @ 1 > initcall tc_filter_init+0x0/0x4c returned 0 after 0 usecs > calling tc_action_init+0x0/0x4c @ 1 > initcall tc_action_init+0x0/0x4c returned 0 after 0 usecs > calling genl_init+0x0/0x8f @ 1 > initcall genl_init+0x0/0x8f returned 0 after 976 usecs > calling cipso_v4_init+0x0/0x88 @ 1 > initcall cipso_v4_init+0x0/0x88 returned 0 after 0 usecs > calling wireless_nlevent_init+0x0/0x12 @ 1 > initcall wireless_nlevent_init+0x0/0x12 returned 0 after 0 usecs > calling netlbl_init+0x0/0x81 @ 1 > NetLabel: Initializing > NetLabel: domain hash size = 128 > NetLabel: protocols = UNLABELED CIPSOv4 > NetLabel: unlabeled traffic allowed by default > initcall netlbl_init+0x0/0x81 returned 0 after 0 usecs > calling sysctl_init+0x0/0x49 @ 1 > initcall sysctl_init+0x0/0x49 returned 0 after 0 usecs > calling xen_mc_debugfs+0x0/0x118 @ 1 > initcall xen_mc_debugfs+0x0/0x118 returned 0 after 976 usecs > calling xen_mmu_debugfs+0x0/0x2be @ 1 > initcall xen_mmu_debugfs+0x0/0x2be returned 0 after 976 usecs > calling print_all_ICs+0x0/0x567 @ 1 > initcall print_all_ICs+0x0/0x567 returned 0 after 976 usecs > calling hpet_late_init+0x0/0x1d1 @ 1 > initcall hpet_late_init+0x0/0x1d1 returned -19 after 0 usecs > calling init_k8_nbs+0x0/0x28 @ 1 > initcall init_k8_nbs+0x0/0x28 returned 0 after 0 usecs > calling clocksource_done_booting+0x0/0x5e @ 1 > Switching to clocksource xen > kstop/0 used greatest stack depth: 6296 bytes left > initcall clocksource_done_booting+0x0/0x5e returned 0 after 8895 usecs > calling ftrace_init_debugfs+0x0/0x241 @ 1 > initcall ftrace_init_debugfs+0x0/0x241 returned 0 after 653 usecs > calling rb_init_debugfs+0x0/0x2f @ 1 > initcall rb_init_debugfs+0x0/0x2f returned 0 after 18 usecs > calling tracer_init_debugfs+0x0/0x347 @ 1 > initcall tracer_init_debugfs+0x0/0x347 returned 0 after 2609 usecs > calling init_trace_printk_function_export+0x0/0x2f @ 1 > initcall init_trace_printk_function_export+0x0/0x2f returned 0 after 18 > usecs > calling stat_workqueue_init+0x0/0x2d @ 1 > initcall stat_workqueue_init+0x0/0x2d returned 0 after 21 usecs > calling event_trace_init+0x0/0x1ed @ 1 > initcall event_trace_init+0x0/0x1ed returned 0 after 87492 usecs > calling init_pipe_fs+0x0/0x4d @ 1 > initcall init_pipe_fs+0x0/0x4d returned 0 after 212 usecs > calling eventpoll_init+0x0/0xda @ 1 > initcall eventpoll_init+0x0/0xda returned 0 after 121 usecs > calling anon_inode_init+0x0/0x128 @ 1 > initcall anon_inode_init+0x0/0x128 returned 0 after 142 usecs > calling blk_scsi_ioctl_init+0x0/0x297 @ 1 > initcall blk_scsi_ioctl_init+0x0/0x297 returned 0 after 0 usecs > calling acpi_event_init+0x0/0x80 @ 1 > initcall acpi_event_init+0x0/0x80 returned 0 after 155 usecs > calling pnpacpi_init+0x0/0x8c @ 1 > pnp: PnP ACPI init > ACPI: bus type pnp registered > xen: registering gsi 8 triggering 1 polarity 0 > xen_allocate_pirq: returning irq 8 for gsi 8 > xen: --> irq=8 > xen: registering gsi 13 triggering 1 polarity 0 > xen_allocate_pirq: returning irq 13 for gsi 13 > xen: --> irq=13 > xen: registering gsi 4 triggering 1 polarity 0 > xen_allocate_pirq: returning irq 4 for gsi 4 > xen: --> irq=4 > Already setup the GSI :4 > xen: registering gsi 3 triggering 1 polarity 0 > xen_allocate_pirq: returning irq 3 for gsi 3 > xen: --> irq=3 > pnp: PnP ACPI: found 14 devices > ACPI: ACPI bus type pnp unregistered > initcall pnpacpi_init+0x0/0x8c returned 0 after 72877 usecs > calling pnp_system_init+0x0/0x12 @ 1 > system 00:01: iomem range 0xfed1c000-0xfed1ffff has been reserved > system 00:06: ioport range 0xa00-0xa0f has been reserved > system 00:06: ioport range 0x290-0x29f has been reserved > system 00:07: ioport range 0xca2-0xca3 has been reserved > system 00:07: ioport range 0xcf8-0xcff could not be reserved > system 00:07: ioport range 0x4d0-0x4d1 has been reserved > system 00:07: ioport range 0x800-0x87f has been reserved > system 00:07: ioport range 0x500-0x57f could not be reserved > system 00:07: iomem range 0xfed1c000-0xfed1ffff has been reserved > system 00:07: iomem range 0xfed20000-0xfed3ffff has been reserved > system 00:07: iomem range 0xfed40000-0xfed8ffff has been reserved > system 00:09: iomem range 0xfec00000-0xfec00fff could not be reserved > system 00:09: iomem range 0xfee00000-0xfee00fff has been reserved > system 00:0c: iomem range 0xe0000000-0xefffffff has been reserved > system 00:0d: iomem range 0xc0000-0xcffff could not be reserved > system 00:0d: iomem range 0xe0000-0xfffff could not be reserved > system 00:0d: iomem range 0xfed90000-0xffffffff could not be reserved > initcall pnp_system_init+0x0/0x12 returned 0 after 93585 usecs > calling pcistub_init+0x0/0x1e7 @ 1 > initcall pcistub_init+0x0/0x1e7 returned 0 after 1622 usecs > calling chr_dev_init+0x0/0xc7 @ 1 > initcall chr_dev_init+0x0/0xc7 returned 0 after 922 usecs > calling firmware_class_init+0x0/0x79 @ 1 > initcall firmware_class_init+0x0/0x79 returned 0 after 96 usecs > calling init_pcmcia_bus+0x0/0x84 @ 1 > initcall init_pcmcia_bus+0x0/0x84 returned 0 after 124 usecs > calling cpufreq_gov_performance_init+0x0/0x12 @ 1 > initcall cpufreq_gov_performance_init+0x0/0x12 returned 0 after 16 usecs > calling cpufreq_gov_userspace_init+0x0/0x12 @ 1 > initcall cpufreq_gov_userspace_init+0x0/0x12 returned 0 after 2 usecs > calling init_acpi_pm_clocksource+0x0/0xef @ 1 > PM-Timer failed consistency check (0x0xffffff) - aborting. > initcall init_acpi_pm_clocksource+0x0/0xef returned -19 after 9691 usecs > calling pcibios_assign_resources+0x0/0x74 @ 1 > pci 0000:00:01.0: PCI bridge, secondary bus 0000:01 > pci 0000:00:01.0: IO window: 0xb000-0xbfff > pci 0000:00:01.0: MEM window: 0xf3f00000-0xf6ffffff > pci 0000:00:01.0: PREFETCH window: 0x000000c0000000-0x000000cfffffff > pci 0000:00:03.0: PCI bridge, secondary bus 0000:02 > pci 0000:00:03.0: IO window: disabled > pci 0000:00:03.0: MEM window: disabled > pci 0000:00:03.0: PREFETCH window: disabled > pci 0000:00:07.0: PCI bridge, secondary bus 0000:03 > pci 0000:00:07.0: IO window: 0xc000-0xcfff > pci 0000:00:07.0: MEM window: 0xf7f00000-0xfaffffff > pci 0000:00:07.0: PREFETCH window: 0x000000d0000000-0x000000dfffffff > pci 0000:04:00.0: PCI bridge, secondary bus 0000:05 > pci 0000:04:00.0: IO window: disabled > pci 0000:04:00.0: MEM window: 0xfbc00000-0xfbcfffff > pci 0000:04:00.0: PREFETCH window: 0x000000f2f00000-0x000000f2ffffff > pci 0000:04:00.2: PCI bridge, secondary bus 0000:06 > pci 0000:04:00.2: IO window: disabled > pci 0000:04:00.2: MEM window: disabled > pci 0000:04:00.2: PREFETCH window: disabled > pci 0000:00:1c.0: PCI bridge, secondary bus 0000:04 > pci 0000:00:1c.0: IO window: 0x1000-0x1fff > pci 0000:00:1c.0: MEM window: 0xfbc00000-0xfbcfffff > pci 0000:00:1c.0: PREFETCH window: 0x000000f2f00000-0x000000f2ffffff > pci 0000:00:1c.4: PCI bridge, secondary bus 0000:07 > pci 0000:00:1c.4: IO window: 0xd000-0xdfff > pci 0000:00:1c.4: MEM window: 0xfbd00000-0xfbdfffff > pci 0000:00:1c.4: PREFETCH window: 0x000000f0000000-0x000000f01fffff > pci 0000:00:1c.5: PCI bridge, secondary bus 0000:08 > pci 0000:00:1c.5: IO window: 0xe000-0xefff > pci 0000:00:1c.5: MEM window: 0xfbe00000-0xfbefffff > pci 0000:00:1c.5: PREFETCH window: 0x000000f0200000-0x000000f03fffff > pci 0000:00:1e.0: PCI bridge, secondary bus 0000:09 > pci 0000:00:1e.0: IO window: disabled > pci 0000:00:1e.0: MEM window: disabled > pci 0000:00:1e.0: PREFETCH window: disabled > pci 0000:00:01.0: setting latency timer to 64 > pci 0000:00:03.0: setting latency timer to 64 > pci 0000:00:07.0: setting latency timer to 64 > pci 0000:00:1c.0: enabling device (0106 -> 0107) > xen: registering gsi 17 triggering 0 polarity 1 > alloc irq_desc for 17 on node 0 > alloc kstat_irqs on node 0 > xen: --> irq=17 > pci 0000:00:1c.0: PCI INT A -> GSI 17 (level, low) -> IRQ 17 > pci 0000:00:1c.0: setting latency timer to 64 > pci 0000:04:00.0: setting latency timer to 64 > pci 0000:04:00.2: setting latency timer to 64 > xen: registering gsi 17 triggering 0 polarity 1 > xen_allocate_pirq: returning irq 17 for gsi 17 > xen: --> irq=17 > Already setup the GSI :17 > pci 0000:00:1c.4: PCI INT A -> GSI 17 (level, low) -> IRQ 17 > pci 0000:00:1c.4: setting latency timer to 64 > xen: registering gsi 16 triggering 0 polarity 1 > alloc irq_desc for 16 on node 0 > alloc kstat_irqs on node 0 > xen: --> irq=16 > pci 0000:00:1c.5: PCI INT B -> GSI 16 (level, low) -> IRQ 16 > pci 0000:00:1c.5: setting latency timer to 64 > pci 0000:00:1e.0: setting latency timer to 64 > pci_bus 0000:00: resource 0 io: [0x00-0xffff] > pci_bus 0000:00: resource 1 mem: [0x000000-0xffffffffffffffff] > pci_bus 0000:01: resource 0 io: [0xb000-0xbfff] > pci_bus 0000:01: resource 1 mem: [0xf3f00000-0xf6ffffff] > pci_bus 0000:01: resource 2 pref mem [0xc0000000-0xcfffffff] > pci_bus 0000:03: resource 0 io: [0xc000-0xcfff] > pci_bus 0000:03: resource 1 mem: [0xf7f00000-0xfaffffff] > pci_bus 0000:03: resource 2 pref mem [0xd0000000-0xdfffffff] > pci_bus 0000:04: resource 0 io: [0x1000-0x1fff] > pci_bus 0000:04: resource 1 mem: [0xfbc00000-0xfbcfffff] > pci_bus 0000:04: resource 2 pref mem [0xf2f00000-0xf2ffffff] > pci_bus 0000:05: resource 1 mem: [0xfbc00000-0xfbcfffff] > pci_bus 0000:05: resource 2 pref mem [0xf2f00000-0xf2ffffff] > pci_bus 0000:07: resource 0 io: [0xd000-0xdfff] > pci_bus 0000:07: resource 1 mem: [0xfbd00000-0xfbdfffff] > pci_bus 0000:07: resource 2 pref mem [0xf0000000-0xf01fffff] > pci_bus 0000:08: resource 0 io: [0xe000-0xefff] > pci_bus 0000:08: resource 1 mem: [0xfbe00000-0xfbefffff] > pci_bus 0000:08: resource 2 pref mem [0xf0200000-0xf03fffff] > pci_bus 0000:09: resource 3 io: [0x00-0xffff] > pci_bus 0000:09: resource 4 mem: [0x000000-0xffffffffffffffff] > initcall pcibios_assign_resources+0x0/0x74 returned 0 after 361318 usecs > calling sysctl_core_init+0x0/0x38 @ 1 > initcall sysctl_core_init+0x0/0x38 returned 0 after 105 usecs > calling inet_init+0x0/0x209 @ 1 > NET: Registered protocol family 2 > IP route cache hash table entries: 524288 (order: 10, 4194304 bytes) > TCP established hash table entries: 524288 (order: 11, 8388608 bytes) > TCP bind hash table entries: 65536 (order: 10, 4718592 bytes) > TCP: Hash tables configured (established 524288 bind 65536) > TCP reno registered > initcall inet_init+0x0/0x209 returned 0 after 40865 usecs > calling af_unix_init+0x0/0x55 @ 1 > NET: Registered protocol family 1 > initcall af_unix_init+0x0/0x55 returned 0 after 3095 usecs > calling pci_apply_final_quirks+0x0/0x36 @ 1 > pci 0000:03:00.0: Boot video device > pci 0000:04:00.0: rerouting interrupts for [8086:0370] > pci 0000:04:00.2: rerouting interrupts for [8086:0372] > initcall pci_apply_final_quirks+0x0/0x36 returned 0 after 13680 usecs > calling populate_rootfs+0x0/0x263 @ 1 > Trying to unpack rootfs image as initramfs... > Freeing initrd memory: 214149k freed > initcall populate_rootfs+0x0/0x263 returned 0 after 592711 usecs > calling pci_iommu_init+0x0/0x50 @ 1 > DMA-API: preallocated 32768 debug entries > DMA-API: debugging enabled by kernel config > PCI-DMA: Using software bounce buffering for IO (SWIOTLB) > DMA: Placing 64MB software IO TLB between ffff880020000000 - > ffff880024000000 > DMA: software IO TLB at phys 0x20000000 - 0x24000000 > initcall pci_iommu_init+0x0/0x50 returned 0 after 61360 usecs > calling calgary_fixup_tce_spaces+0x0/0xf9 @ 1 > initcall calgary_fixup_tce_spaces+0x0/0xf9 returned -19 after 0 usecs > calling i8259A_init_sysfs+0x0/0x22 @ 1 > initcall i8259A_init_sysfs+0x0/0x22 returned 0 after 109 usecs > calling vsyscall_init+0x0/0x6c @ 1 > initcall vsyscall_init+0x0/0x6c returned 0 after 117 usecs > calling sbf_init+0x0/0xef @ 1 > initcall sbf_init+0x0/0xef returned 0 after 0 usecs > calling i8237A_init_sysfs+0x0/0x22 @ 1 > initcall i8237A_init_sysfs+0x0/0x22 returned 0 after 80 usecs > calling add_rtc_cmos+0x0/0xc4 @ 1 > initcall add_rtc_cmos+0x0/0xc4 returned 0 after 3 usecs > calling cache_sysfs_init+0x0/0x67 @ 1 > initcall cache_sysfs_init+0x0/0x67 returned 0 after 6102 usecs > calling mce_init_device+0x0/0x109 @ 1 > initcall mce_init_device+0x0/0x109 returned 0 after 2029 usecs > calling threshold_init_device+0x0/0x98 @ 1 > initcall threshold_init_device+0x0/0x98 returned 0 after 1 usecs > calling thermal_throttle_init_device+0x0/0x93 @ 1 > initcall thermal_throttle_init_device+0x0/0x93 returned 0 after 0 usecs > calling msr_init+0x0/0x14c @ 1 > initcall msr_init+0x0/0x14c returned 0 after 1693 usecs > calling cpuid_init+0x0/0x14c @ 1 > initcall cpuid_init+0x0/0x14c returned 0 after 1636 usecs > calling ioapic_init_sysfs+0x0/0xa7 @ 1 > initcall ioapic_init_sysfs+0x0/0xa7 returned 0 after 114 usecs > calling add_pcspkr+0x0/0x28 @ 1 > initcall add_pcspkr+0x0/0x28 returned 0 after 77 usecs > calling audit_classes_init+0x0/0xaf @ 1 > initcall audit_classes_init+0x0/0xaf returned 0 after 13 usecs > calling pt_dump_init+0x0/0x30 @ 1 > initcall pt_dump_init+0x0/0x30 returned 0 after 66 usecs > calling init_vdso_vars+0x0/0x220 @ 1 > initcall init_vdso_vars+0x0/0x220 returned 0 after 46 usecs > calling ia32_binfmt_init+0x0/0x14 @ 1 > initcall ia32_binfmt_init+0x0/0x14 returned 0 after 32 usecs > calling sysenter_setup+0x0/0x2df @ 1 > initcall sysenter_setup+0x0/0x2df returned 0 after 3 usecs > calling init_sched_debug_procfs+0x0/0x2c @ 1 > initcall init_sched_debug_procfs+0x0/0x2c returned 0 after 15 usecs > calling proc_schedstat_init+0x0/0x22 @ 1 > initcall proc_schedstat_init+0x0/0x22 returned 0 after 10 usecs > calling proc_execdomains_init+0x0/0x22 @ 1 > initcall proc_execdomains_init+0x0/0x22 returned 0 after 10 usecs > calling ioresources_init+0x0/0x3c @ 1 > initcall ioresources_init+0x0/0x3c returned 0 after 50 usecs > calling uid_cache_init+0x0/0x8d @ 1 > initcall uid_cache_init+0x0/0x8d returned 0 after 71 usecs > calling init_posix_timers+0x0/0x19f @ 1 > initcall init_posix_timers+0x0/0x19f returned 0 after 66 usecs > calling init_posix_cpu_timers+0x0/0xe5 @ 1 > initcall init_posix_cpu_timers+0x0/0xe5 returned 0 after 0 usecs > calling nsproxy_cache_init+0x0/0x2d @ 1 > initcall nsproxy_cache_init+0x0/0x2d returned 0 after 88 usecs > calling create_proc_profile+0x0/0x282 @ 1 > initcall create_proc_profile+0x0/0x282 returned 0 after 0 usecs > calling timekeeping_init_device+0x0/0x22 @ 1 > initcall timekeeping_init_device+0x0/0x22 returned 0 after 81 usecs > calling init_clocksource_sysfs+0x0/0x50 @ 1 > initcall init_clocksource_sysfs+0x0/0x50 returned 0 after 113 usecs > calling init_timer_list_procfs+0x0/0x2c @ 1 > initcall init_timer_list_procfs+0x0/0x2c returned 0 after 11 usecs > calling init_tstats_procfs+0x0/0x2c @ 1 > initcall init_tstats_procfs+0x0/0x2c returned 0 after 10 usecs > calling lockdep_proc_init+0x0/0x7c @ 1 > initcall lockdep_proc_init+0x0/0x7c returned 0 after 38 usecs > calling futex_init+0x0/0xbe @ 1 > initcall futex_init+0x0/0xbe returned 0 after 71 usecs > calling proc_dma_init+0x0/0x22 @ 1 > initcall proc_dma_init+0x0/0x22 returned 0 after 11 usecs > calling proc_modules_init+0x0/0x22 @ 1 > initcall proc_modules_init+0x0/0x22 returned 0 after 10 usecs > calling kallsyms_init+0x0/0x25 @ 1 > initcall kallsyms_init+0x0/0x25 returned 0 after 10 usecs > calling snapshot_device_init+0x0/0x12 @ 1 > initcall snapshot_device_init+0x0/0x12 returned 0 after 83 usecs > calling crash_save_vmcoreinfo_init+0x0/0x46d @ 1 > initcall crash_save_vmcoreinfo_init+0x0/0x46d returned 0 after 22 usecs > calling crash_notes_memory_init+0x0/0x38 @ 1 > initcall crash_notes_memory_init+0x0/0x38 returned 0 after 11 usecs > calling pid_namespaces_init+0x0/0x2d @ 1 > initcall pid_namespaces_init+0x0/0x2d returned 0 after 100 usecs > calling ikconfig_init+0x0/0x39 @ 1 > initcall ikconfig_init+0x0/0x39 returned 0 after 11 usecs > calling audit_init+0x0/0x153 @ 1 > audit: initializing netlink socket (disabled) > type=2000 audit(1275218265.439:1): initialized > initcall audit_init+0x0/0x153 returned 0 after 8236 usecs > calling audit_tree_init+0x0/0x49 @ 1 > initcall audit_tree_init+0x0/0x49 returned 0 after 2 usecs > calling init_kprobes+0x0/0x19e @ 1 > initcall init_kprobes+0x0/0x19e returned 0 after 12070 usecs > calling hung_task_init+0x0/0x53 @ 1 > initcall hung_task_init+0x0/0x53 returned 0 after 203 usecs > calling utsname_sysctl_init+0x0/0x14 @ 1 > initcall utsname_sysctl_init+0x0/0x14 returned 0 after 83 usecs > calling init_tracepoints+0x0/0x17 @ 1 > initcall init_tracepoints+0x0/0x17 returned 0 after 0 usecs > calling init_lstats_procfs+0x0/0x25 @ 1 > initcall init_lstats_procfs+0x0/0x25 returned 0 after 12 usecs > calling ftrace_mod_cmd_init+0x0/0x12 @ 1 > initcall ftrace_mod_cmd_init+0x0/0x12 returned 0 after 18 usecs > calling init_events+0x0/0x63 @ 1 > initcall init_events+0x0/0x63 returned 0 after 11 usecs > calling init_sched_switch_trace+0x0/0x12 @ 1 > initcall init_sched_switch_trace+0x0/0x12 returned 0 after 3 usecs > calling init_stack_trace+0x0/0x12 @ 1 > initcall init_stack_trace+0x0/0x12 returned 0 after 1 usecs > calling init_function_trace+0x0/0x3e @ 1 > initcall init_function_trace+0x0/0x3e returned 0 after 3 usecs > calling init_wakeup_tracer+0x0/0x22 @ 1 > initcall init_wakeup_tracer+0x0/0x22 returned 0 after 3 usecs > calling stack_trace_init+0x0/0x6b @ 1 > initcall stack_trace_init+0x0/0x6b returned 0 after 38 usecs > calling init_mmio_trace+0x0/0x12 @ 1 > initcall init_mmio_trace+0x0/0x12 returned 0 after 1 usecs > calling init_graph_trace+0x0/0x32 @ 1 > initcall init_graph_trace+0x0/0x32 returned 0 after 2 usecs > calling init_kmem_tracer+0x0/0x56 @ 1 > initcall init_kmem_tracer+0x0/0x56 returned 0 after 4 usecs > calling init_blk_tracer+0x0/0x57 @ 1 > initcall init_blk_tracer+0x0/0x57 returned 0 after 3 usecs > calling perf_event_sysfs_init+0x0/0x19 @ 1 > initcall perf_event_sysfs_init+0x0/0x19 returned 0 after 14 usecs > calling init_per_zone_wmark_min+0x0/0x68 @ 1 > initcall init_per_zone_wmark_min+0x0/0x68 returned 0 after 899 usecs > calling kswapd_init+0x0/0x78 @ 1 > initcall kswapd_init+0x0/0x78 returned 0 after 336 usecs > calling setup_vmstat+0x0/0xc3 @ 1 > initcall setup_vmstat+0x0/0xc3 returned 0 after 180 usecs > calling mm_sysfs_init+0x0/0x29 @ 1 > initcall mm_sysfs_init+0x0/0x29 returned 0 after 9 usecs > calling proc_vmalloc_init+0x0/0x25 @ 1 > initcall proc_vmalloc_init+0x0/0x25 returned 0 after 10 usecs > calling procswaps_init+0x0/0x22 @ 1 > initcall procswaps_init+0x0/0x22 returned 0 after 10 usecs > calling hugetlb_init+0x0/0x3c8 @ 1 > HugeTLB registered 2 MB page size, pre-allocated 0 pages > initcall hugetlb_init+0x0/0x3c8 returned 0 after 5058 usecs > calling slab_proc_init+0x0/0x25 @ 1 > initcall slab_proc_init+0x0/0x25 returned 0 after 11 usecs > calling slab_sysfs_init+0x0/0xf0 @ 1 > initcall slab_sysfs_init+0x0/0xf0 returned 0 after 17492 usecs > calling fasync_init+0x0/0x2a @ 1 > initcall fasync_init+0x0/0x2a returned 0 after 247 usecs > calling proc_filesystems_init+0x0/0x22 @ 1 > initcall proc_filesystems_init+0x0/0x22 returned 0 after 12 usecs > calling dnotify_init+0x0/0x80 @ 1 > initcall dnotify_init+0x0/0x80 returned 0 after 546 usecs > calling inotify_setup+0x0/0x12 @ 1 > initcall inotify_setup+0x0/0x12 returned 0 after 0 usecs > calling inotify_user_setup+0x0/0xbe @ 1 > initcall inotify_user_setup+0x0/0xbe returned 0 after 651 usecs > calling aio_setup+0x0/0xa5 @ 1 > initcall aio_setup+0x0/0xa5 returned 0 after 3119 usecs > calling proc_locks_init+0x0/0x22 @ 1 > initcall proc_locks_init+0x0/0x22 returned 0 after 13 usecs > calling init_sys32_ioctl+0x0/0x85 @ 1 > initcall init_sys32_ioctl+0x0/0x85 returned 0 after 12 usecs > calling init_mbcache+0x0/0x14 @ 1 > initcall init_mbcache+0x0/0x14 returned 0 after 1 usecs > calling dquot_init+0x0/0x105 @ 1 > VFS: Disk quotas dquot_6.5.2 > Dquot-cache hash table entries: 512 (order 0, 4096 bytes) > initcall dquot_init+0x0/0x105 returned 0 after 8080 usecs > calling init_v2_quota_format+0x0/0x12 @ 1 > initcall init_v2_quota_format+0x0/0x12 returned 0 after 16 usecs > calling proc_cmdline_init+0x0/0x22 @ 1 > initcall proc_cmdline_init+0x0/0x22 returned 0 after 12 usecs > calling proc_cpuinfo_init+0x0/0x22 @ 1 > initcall proc_cpuinfo_init+0x0/0x22 returned 0 after 10 usecs > calling proc_devices_init+0x0/0x22 @ 1 > initcall proc_devices_init+0x0/0x22 returned 0 after 43 usecs > calling proc_interrupts_init+0x0/0x22 @ 1 > initcall proc_interrupts_init+0x0/0x22 returned 0 after 10 usecs > calling proc_loadavg_init+0x0/0x22 @ 1 > initcall proc_loadavg_init+0x0/0x22 returned 0 after 10 usecs > calling proc_meminfo_init+0x0/0x22 @ 1 > initcall proc_meminfo_init+0x0/0x22 returned 0 after 10 usecs > calling proc_stat_init+0x0/0x22 @ 1 > initcall proc_stat_init+0x0/0x22 returned 0 after 10 usecs > calling proc_uptime_init+0x0/0x22 @ 1 > initcall proc_uptime_init+0x0/0x22 returned 0 after 10 usecs > calling proc_version_init+0x0/0x22 @ 1 > initcall proc_version_init+0x0/0x22 returned 0 after 10 usecs > calling proc_softirqs_init+0x0/0x22 @ 1 > initcall proc_softirqs_init+0x0/0x22 returned 0 after 10 usecs > calling proc_kcore_init+0x0/0xa9 @ 1 > initcall proc_kcore_init+0x0/0xa9 returned 0 after 31 usecs > calling vmcore_init+0x0/0x8d2 @ 1 > initcall vmcore_init+0x0/0x8d2 returned 0 after 0 usecs > calling proc_kmsg_init+0x0/0x25 @ 1 > initcall proc_kmsg_init+0x0/0x25 returned 0 after 10 usecs > calling proc_page_init+0x0/0x42 @ 1 > initcall proc_page_init+0x0/0x42 returned 0 after 19 usecs > calling init_devpts_fs+0x0/0x4c @ 1 > initcall init_devpts_fs+0x0/0x4c returned 0 after 239 usecs > calling init_ext3_fs+0x0/0x71 @ 1 > initcall init_ext3_fs+0x0/0x71 returned 0 after 568 usecs > calling init_ext4_fs+0x0/0xea @ 1 > initcall init_ext4_fs+0x0/0xea returned 0 after 1547 usecs > calling journal_init+0x0/0x93 @ 1 > initcall journal_init+0x0/0x93 returned 0 after 975 usecs > calling journal_init+0x0/0xec @ 1 > initcall journal_init+0x0/0xec returned 0 after 1124 usecs > calling init_ramfs_fs+0x0/0x12 @ 1 > initcall init_ramfs_fs+0x0/0x12 returned 0 after 3 usecs > calling init_hugetlbfs_fs+0x0/0x98 @ 1 > initcall init_hugetlbfs_fs+0x0/0x98 returned 0 after 444 usecs > calling init_iso9660_fs+0x0/0x71 @ 1 > initcall init_iso9660_fs+0x0/0x71 returned 0 after 306 usecs > calling init_nls_cp437+0x0/0x12 @ 1 > initcall init_nls_cp437+0x0/0x12 returned 0 after 16 usecs > calling init_nls_ascii+0x0/0x12 @ 1 > initcall init_nls_ascii+0x0/0x12 returned 0 after 1 usecs > calling ipc_init+0x0/0x23 @ 1 > msgmni has been set to 21017 > initcall ipc_init+0x0/0x23 returned 0 after 2645 usecs > calling ipc_sysctl_init+0x0/0x14 @ 1 > initcall ipc_sysctl_init+0x0/0x14 returned 0 after 140 usecs > calling init_mqueue_fs+0x0/0xc9 @ 1 > initcall init_mqueue_fs+0x0/0xc9 returned 0 after 600 usecs > calling key_proc_init+0x0/0x59 @ 1 > initcall key_proc_init+0x0/0x59 returned 0 after 23 usecs > calling selinux_nf_ip_init+0x0/0x60 @ 1 > SELinux: Registering netfilter hooks > initcall selinux_nf_ip_init+0x0/0x60 returned 0 after 3407 usecs > calling init_sel_fs+0x0/0x68 @ 1 > initcall init_sel_fs+0x0/0x68 returned 0 after 996 usecs > calling selnl_init+0x0/0x4d @ 1 > initcall selnl_init+0x0/0x4d returned 0 after 54 usecs > calling sel_netif_init+0x0/0x66 @ 1 > initcall sel_netif_init+0x0/0x66 returned 0 after 6 usecs > calling sel_netnode_init+0x0/0x73 @ 1 > initcall sel_netnode_init+0x0/0x73 returned 0 after 2 usecs > calling sel_netport_init+0x0/0x73 @ 1 > initcall sel_netport_init+0x0/0x73 returned 0 after 9 usecs > calling aurule_init+0x0/0x37 @ 1 > initcall aurule_init+0x0/0x37 returned 0 after 0 usecs > calling crypto_wq_init+0x0/0x32 @ 1 > initcall crypto_wq_init+0x0/0x32 returned 0 after 2705 usecs > calling crypto_algapi_init+0x0/0xd @ 1 > initcall crypto_algapi_init+0x0/0xd returned 0 after 49 usecs > calling skcipher_module_init+0x0/0x35 @ 1 > initcall skcipher_module_init+0x0/0x35 returned 0 after 0 usecs > calling chainiv_module_init+0x0/0x12 @ 1 > initcall chainiv_module_init+0x0/0x12 returned 0 after 37 usecs > calling eseqiv_module_init+0x0/0x12 @ 1 > initcall eseqiv_module_init+0x0/0x12 returned 0 after 2 usecs > calling hmac_module_init+0x0/0x12 @ 1 > initcall hmac_module_init+0x0/0x12 returned 0 after 1 usecs > calling md5_mod_init+0x0/0x12 @ 1 > cryptomgr_test used greatest stack depth: 5672 bytes left > initcall md5_mod_init+0x0/0x12 returned 0 after 415 usecs > calling sha1_generic_mod_init+0x0/0x12 @ 1 > initcall sha1_generic_mod_init+0x0/0x12 returned 0 after 271 usecs > calling crc32c_mod_init+0x0/0x12 @ 1 > initcall crc32c_mod_init+0x0/0x12 returned 0 after 330 usecs > calling krng_mod_init+0x0/0x12 @ 1 > alg: No test for stdrng (krng) > initcall krng_mod_init+0x0/0x12 returned 0 after 212 usecs > calling proc_genhd_init+0x0/0x3c @ 1 > initcall proc_genhd_init+0x0/0x3c returned 0 after 24 usecs > calling bsg_init+0x0/0x132 @ 1 > Block layer SCSI generic (bsg) driver version 0.4 loaded (major 252) > initcall bsg_init+0x0/0x132 returned 0 after 308 usecs > calling noop_init+0x0/0x14 @ 1 > io scheduler noop registered > initcall noop_init+0x0/0x14 returned 0 after 19 usecs > calling as_init+0x0/0x14 @ 1 > io scheduler anticipatory registered > initcall as_init+0x0/0x14 returned 0 after 2 usecs > calling deadline_init+0x0/0x14 @ 1 > io scheduler deadline registered > initcall deadline_init+0x0/0x14 returned 0 after 2 usecs > calling cfq_init+0x0/0x94 @ 1 > io scheduler cfq registered (default) > initcall cfq_init+0x0/0x94 returned 0 after 495 usecs > calling debug_objects_init_debugfs+0x0/0x64 @ 1 > initcall debug_objects_init_debugfs+0x0/0x64 returned 0 after 80 usecs > calling percpu_counter_startup+0x0/0x38 @ 1 > initcall percpu_counter_startup+0x0/0x38 returned 0 after 2 usecs > calling dynamic_debug_init+0x0/0x127 @ 1 > initcall dynamic_debug_init+0x0/0x127 returned 0 after 328 usecs > calling pci_proc_init+0x0/0x6b @ 1 > initcall pci_proc_init+0x0/0x6b returned 0 after 820 usecs > calling pcie_portdrv_init+0x0/0x4c @ 1 > alloc irq_desc for 4269 on node 0 > alloc kstat_irqs on node 0 > pcieport 0000:00:01.0: setting latency timer to 64 > alloc irq_desc for 4268 on node 0 > alloc kstat_irqs on node 0 > pcieport 0000:00:03.0: setting latency timer to 64 > alloc irq_desc for 4267 on node 0 > alloc kstat_irqs on node 0 > pcieport 0000:00:07.0: setting latency timer to 64 > alloc irq_desc for 4266 on node 0 > alloc kstat_irqs on node 0 > pcieport 0000:00:1c.0: setting latency timer to 64 > alloc irq_desc for 4265 on node 0 > alloc kstat_irqs on node 0 > pcieport 0000:00:1c.4: setting latency timer to 64 > alloc irq_desc for 4264 on node 0 > alloc kstat_irqs on node 0 > pcieport 0000:00:1c.5: setting latency timer to 64 > initcall pcie_portdrv_init+0x0/0x4c returned 0 after 4286 usecs > calling aer_service_init+0x0/0x2b @ 1 > aer 0000:00:01.0:pcie02: AER service couldn''t init device: no _OSC > support > aer 0000:00:03.0:pcie02: AER service couldn''t init device: no _OSC > support > aer 0000:00:07.0:pcie02: AER service couldn''t init device: no _OSC > support > initcall aer_service_init+0x0/0x2b returned 0 after 202 usecs > calling pci_hotplug_init+0x0/0x1d @ 1 > pci_hotplug: PCI Hot Plug PCI Core version: 0.5 > initcall pci_hotplug_init+0x0/0x1d returned 0 after 1 usecs > calling pcied_init+0x0/0x79 @ 1 > pciehp: PCI Express Hot Plug Controller Driver version: 0.4 > initcall pcied_init+0x0/0x79 returned 0 after 646 usecs > calling acpiphp_init+0x0/0x5f @ 1 > acpiphp: ACPI Hot Plug PCI Controller Driver version: 0.5 > initcall acpiphp_init+0x0/0x5f returned -19 after 2301 usecs > calling pci_stub_init+0x0/0x139 @ 1 > pci-stub: invalid id string "" > initcall pci_stub_init+0x0/0x139 returned 0 after 146 usecs > calling fb_console_init+0x0/0x11d @ 1 > cryptomgr_test used greatest stack depth: 5400 bytes left > initcall fb_console_init+0x0/0x11d returned 0 after 291391 usecs > calling xenfb_init+0x0/0x5d @ 1 > initcall xenfb_init+0x0/0x5d returned -19 after 0 usecs > calling vesafb_init+0x0/0x23a @ 1 > initcall vesafb_init+0x0/0x23a returned 0 after 195 usecs > calling efifb_init+0x0/0x1ed @ 1 > initcall efifb_init+0x0/0x1ed returned -19 after 4 usecs > calling acpi_reserve_resources+0x0/0xeb @ 1 > initcall acpi_reserve_resources+0x0/0xeb returned 0 after 9 usecs > calling irqrouter_init_sysfs+0x0/0x38 @ 1 > initcall irqrouter_init_sysfs+0x0/0x38 returned 0 after 78 usecs > calling acpi_ac_init+0x0/0x45 @ 1 > initcall acpi_ac_init+0x0/0x45 returned 0 after 182 usecs > calling acpi_button_init+0x0/0x56 @ 1 > input: Power Button > as /devices/LNXSYSTM:00/LNXSYBUS:00/PNP0C0C:00/input/input0 > ACPI: Power Button [PWRB] > input: Power Button as /devices/LNXSYSTM:00/LNXPWRBN:00/input/input1 > ACPI: Power Button [PWRF] > initcall acpi_button_init+0x0/0x56 returned 0 after 18361 usecs > calling acpi_fan_init+0x0/0x56 @ 1 > initcall acpi_fan_init+0x0/0x56 returned 0 after 124 usecs > calling acpi_pci_slot_init+0x0/0x20 @ 1 > initcall acpi_pci_slot_init+0x0/0x20 returned 0 after 1902 usecs > calling acpi_processor_init+0x0/0x132 @ 1 > ACPI: SSDT 00000000bf77e1e0 02B94 (v01 DpgPmm P001Ist 00000011 INTL > 20051117) > ACPI: SSDT 00000000bf780d80 00980 (v01 PmRef P001Cst 00003001 INTL > 20051117) > ACPI: SSDT 00000000bf781700 006E2 (v01 PmRef Cpu0Tst 00003000 INTL > 20051117) > (XEN) cpuid.MWAIT[.eax=40, .ebx=40, .ecx=3, .edx=1120] > (XEN) Monitor-Mwait will be used to enter C-1 state > (XEN) cpuid.MWAIT[.eax=40, .ebx=40, .ecx=3, .edx=1120] > (XEN) Monitor-Mwait will be used to enter C-3 state > (XEN) cpuid.MWAIT[.eax=40, .ebx=40, .ecx=3, .edx=1120] > (XEN) Monitor-Mwait will be used to enter C-3 state > ACPI: CPU-1 (power states: C1[C1] C2[C3] C3[C3]) > (XEN) cpuid.MWAIT[.eax=40, .ebx=40, .ecx=3, .edx=1120] > (XEN) Monitor-Mwait will be used to enter C-1 state > (XEN) cpuid.MWAIT[.eax=40, .ebx=40, .ecx=3, .edx=1120] > (XEN) Monitor-Mwait will be used to enter C-3 state > (XEN) cpuid.MWAIT[.eax=40, .ebx=40, .ecx=3, .edx=1120] > (XEN) Monitor-Mwait will be used to enter C-3 state > ACPI: CPU-1 (power states: C1[C1] C2[C3] C3[C3]) > (XEN) cpuid.MWAIT[.eax=40, .ebx=40, .ecx=3, .edx=1120] > (XEN) Monitor-Mwait will be used to enter C-1 state > (XEN) cpuid.MWAIT[.eax=40, .ebx=40, .ecx=3, .edx=1120] > (XEN) Monitor-Mwait will be used to enter C-3 state > (XEN) cpuid.MWAIT[.eax=40, .ebx=40, .ecx=3, .edx=1120] > (XEN) Monitor-Mwait will be used to enter C-3 state > ACPI: CPU-1 (power states: C1[C1] C2[C3] C3[C3]) > (XEN) cpuid.MWAIT[.eax=40, .ebx=40, .ecx=3, .edx=1120] > (XEN) Monitor-Mwait will be used to enter C-1 state > (XEN) cpuid.MWAIT[.eax=40, .ebx=40, .ecx=3, .edx=1120] > (XEN) Monitor-Mwait will be used to enter C-3 state > (XEN) cpuid.MWAIT[.eax=40, .ebx=40, .ecx=3, .edx=1120] > (XEN) Monitor-Mwait will be used to enter C-3 state > ACPI: CPU-1 (power states: C1[C1] C2[C3] C3[C3]) > (XEN) cpuid.MWAIT[.eax=40, .ebx=40, .ecx=3, .edx=1120] > (XEN) Monitor-Mwait will be used to enter C-1 state > (XEN) cpuid.MWAIT[.eax=40, .ebx=40, .ecx=3, .edx=1120] > (XEN) Monitor-Mwait will be used to enter C-3 state > (XEN) cpuid.MWAIT[.eax=40, .ebx=40, .ecx=3, .edx=1120] > (XEN) Monitor-Mwait will be used to enter C-3 state > ACPI: CPU-1 (power states: C1[C1] C2[C3] C3[C3]) > (XEN) cpuid.MWAIT[.eax=40, .ebx=40, .ecx=3, .edx=1120] > (XEN) Monitor-Mwait will be used to enter C-1 state > (XEN) cpuid.MWAIT[.eax=40, .ebx=40, .ecx=3, .edx=1120] > (XEN) Monitor-Mwait will be used to enter C-3 state > (XEN) cpuid.MWAIT[.eax=40, .ebx=40, .ecx=3, .edx=1120] > (XEN) Monitor-Mwait will be used to enter C-3 state > ACPI: CPU-1 (power states: C1[C1] C2[C3] C3[C3]) > (XEN) cpuid.MWAIT[.eax=40, .ebx=40, .ecx=3, .edx=1120] > (XEN) Monitor-Mwait will be used to enter C-1 state > (XEN) cpuid.MWAIT[.eax=40, .ebx=40, .ecx=3, .edx=1120] > (XEN) Monitor-Mwait will be used to enter C-3 state > (XEN) cpuid.MWAIT[.eax=40, .ebx=40, .ecx=3, .edx=1120] > (XEN) Monitor-Mwait will be used to enter C-3 state > ACPI: CPU-1 (power states: C1[C1] C2[C3] C3[C3]) > (XEN) cpuid.MWAIT[.eax=40, .ebx=40, .ecx=3, .edx=1120] > (XEN) Monitor-Mwait will be used to enter C-1 state > (XEN) cpuid.MWAIT[.eax=40, .ebx=40, .ecx=3, .edx=1120] > (XEN) Monitor-Mwait will be used to enter C-3 state > (XEN) cpuid.MWAIT[.eax=40, .ebx=40, .ecx=3, .edx=1120] > (XEN) Monitor-Mwait will be used to enter C-3 state > ACPI: CPU-1 (power states: C1[C1] C2[C3] C3[C3]) > (XEN) cpuid.MWAIT[.eax=40, .ebx=40, .ecx=3, .edx=1120] > (XEN) Monitor-Mwait will be used to enter C-1 state > (XEN) cpuid.MWAIT[.eax=40, .ebx=40, .ecx=3, .edx=1120] > (XEN) Monitor-Mwait will be used to enter C-3 state > (XEN) cpuid.MWAIT[.eax=40, .ebx=40, .ecx=3, .edx=1120] > (XEN) Monitor-Mwait will be used to enter C-3 state > ACPI: CPU-1 (power states: C1[C1] C2[C3] C3[C3]) > (XEN) cpuid.MWAIT[.eax=40, .ebx=40, .ecx=3, .edx=1120] > (XEN) Monitor-Mwait will be used to enter C-1 state > (XEN) cpuid.MWAIT[.eax=40, .ebx=40, .ecx=3, .edx=1120] > (XEN) Monitor-Mwait will be used to enter C-3 state > (XEN) cpuid.MWAIT[.eax=40, .ebx=40, .ecx=3, .edx=1120] > (XEN) Monitor-Mwait will be used to enter C-3 state > ACPI: CPU-1 (power states: C1[C1] C2[C3] C3[C3]) > (XEN) cpuid.MWAIT[.eax=40, .ebx=40, .ecx=3, .edx=1120] > (XEN) Monitor-Mwait will be used to enter C-1 state > (XEN) cpuid.MWAIT[.eax=40, .ebx=40, .ecx=3, .edx=1120] > (XEN) Monitor-Mwait will be used to enter C-3 state > (XEN) cpuid.MWAIT[.eax=40, .ebx=40, .ecx=3, .edx=1120] > (XEN) Monitor-Mwait will be used to enter C-3 state > ACPI: CPU-1 (power states: C1[C1] C2[C3] C3[C3]) > (XEN) cpuid.MWAIT[.eax=40, .ebx=40, .ecx=3, .edx=1120] > (XEN) Monitor-Mwait will be used to enter C-1 state > (XEN) cpuid.MWAIT[.eax=40, .ebx=40, .ecx=3, .edx=1120] > (XEN) Monitor-Mwait will be used to enter C-3 state > (XEN) cpuid.MWAIT[.eax=40, .ebx=40, .ecx=3, .edx=1120] > (XEN) Monitor-Mwait will be used to enter C-3 state > ACPI: CPU-1 (power states: C1[C1] C2[C3] C3[C3]) > (XEN) cpuid.MWAIT[.eax=40, .ebx=40, .ecx=3, .edx=1120] > (XEN) Monitor-Mwait will be used to enter C-1 state > (XEN) cpuid.MWAIT[.eax=40, .ebx=40, .ecx=3, .edx=1120] > (XEN) Monitor-Mwait will be used to enter C-3 state > (XEN) cpuid.MWAIT[.eax=40, .ebx=40, .ecx=3, .edx=1120] > (XEN) Monitor-Mwait will be used to enter C-3 state > ACPI: CPU-1 (power states: C1[C1] C2[C3] C3[C3]) > (XEN) cpuid.MWAIT[.eax=40, .ebx=40, .ecx=3, .edx=1120] > (XEN) Monitor-Mwait will be used to enter C-1 state > (XEN) cpuid.MWAIT[.eax=40, .ebx=40, .ecx=3, .edx=1120] > (XEN) Monitor-Mwait will be used to enter C-3 state > (XEN) cpuid.MWAIT[.eax=40, .ebx=40, .ecx=3, .edx=1120] > (XEN) Monitor-Mwait will be used to enter C-3 state > ACPI: CPU-1 (power states: C1[C1] C2[C3] C3[C3]) > (XEN) cpuid.MWAIT[.eax=40, .ebx=40, .ecx=3, .edx=1120] > (XEN) Monitor-Mwait will be used to enter C-1 state > (XEN) cpuid.MWAIT[.eax=40, .ebx=40, .ecx=3, .edx=1120] > (XEN) Monitor-Mwait will be used to enter C-3 state > (XEN) cpuid.MWAIT[.eax=40, .ebx=40, .ecx=3, .edx=1120] > (XEN) Monitor-Mwait will be used to enter C-3 state > ACPI: CPU-1 (power states: C1[C1] C2[C3] C3[C3]) > (XEN) cpuid.MWAIT[.eax=40, .ebx=40, .ecx=3, .edx=1120] > (XEN) Monitor-Mwait will be used to enter C-1 state > (XEN) cpuid.MWAIT[.eax=40, .ebx=40, .ecx=3, .edx=1120] > (XEN) Monitor-Mwait will be used to enter C-3 state > (XEN) cpuid.MWAIT[.eax=40, .ebx=40, .ecx=3, .edx=1120] > (XEN) Monitor-Mwait will be used to enter C-3 state > ACPI: CPU-1 (power states: C1[C1] C2[C3] C3[C3]) > initcall acpi_processor_init+0x0/0x132 returned 0 after 629629 usecs > calling acpi_container_init+0x0/0x42 @ 1 > initcall acpi_container_init+0x0/0x42 returned 0 after 13724 usecs > calling acpi_thermal_init+0x0/0x7b @ 1 > initcall acpi_thermal_init+0x0/0x7b returned 0 after 169 usecs > calling acpi_battery_init+0x0/0x16 @ 1 > initcall acpi_battery_init+0x0/0x16 returned 0 after 30 usecs > calling 1_acpi_battery_init_async+0x0/0x3c @ 233 > initcall 1_acpi_battery_init_async+0x0/0x3c returned 0 after 244 usecs > calling evtchn_init+0x0/0x7e @ 1 > Event-channel device installed. > initcall evtchn_init+0x0/0x7e returned 0 after 2902 usecs > calling gntdev_init+0x0/0x3d @ 1 > initcall gntdev_init+0x0/0x3d returned 0 after 117 usecs > calling pciback_init+0x0/0x15f @ 1 > initcall pciback_init+0x0/0x15f returned 0 after 4695 usecs > calling blkif_init+0x0/0x171 @ 1 > initcall blkif_init+0x0/0x171 returned 0 after 3660 usecs > calling blktap_init+0x0/0xa7 @ 1 > blktap_device_init: blktap device major 253 > blktap_ring_init: blktap ring major: 251 > initcall blktap_init+0x0/0xa7 returned 0 after 10464 usecs > calling netback_init+0x0/0x207 @ 1 > registering netback > initcall netback_init+0x0/0x207 returned 0 after 2961 usecs > calling hypervisor_subsys_init+0x0/0x25 @ 1 > initcall hypervisor_subsys_init+0x0/0x25 returned 0 after 0 usecs > calling hyper_sysfs_init+0x0/0xf2 @ 1 > initcall hyper_sysfs_init+0x0/0xf2 returned 0 after 79 usecs > calling platform_pci_module_init+0x0/0xa3 @ 1 > xen-platform-pcifailed backend handshake: unrecognised magic value > initcall platform_pci_module_init+0x0/0xa3 returned -19 after 5839 usecs > calling mcelog_init+0x0/0x1b0 @ 1 > alloc irq_desc for 4263 on node 0 > alloc kstat_irqs on node 0 > initcall mcelog_init+0x0/0x1b0 returned 0 after 6418 usecs > calling rand_initialize+0x0/0x31 @ 1 > initcall rand_initialize+0x0/0x31 returned 0 after 30 usecs > calling tty_init+0x0/0xf5 @ 1 > initcall tty_init+0x0/0xf5 returned 0 after 6277 usecs > calling pty_init+0x0/0x336 @ 1 > initcall pty_init+0x0/0x336 returned 0 after 243 usecs > calling sysrq_init+0x0/0x25 @ 1 > initcall sysrq_init+0x0/0x25 returned 0 after 14 usecs > calling xen_hvc_init+0x0/0xe2 @ 1 > alloc irq_desc for 4262 on node 0 > alloc kstat_irqs on node 0 > initcall xen_hvc_init+0x0/0xe2 returned 0 after 6895 usecs > calling raw_init+0x0/0xe5 @ 1 > initcall raw_init+0x0/0xe5 returned 0 after 149 usecs > calling hpet_init+0x0/0x6a @ 1 > hpet_acpi_add: no address or irqs in _CRS > initcall hpet_init+0x0/0x6a returned 0 after 4307 usecs > calling nvram_init+0x0/0x82 @ 1 > Non-volatile memory driver v1.3 > initcall nvram_init+0x0/0x82 returned 0 after 2886 usecs > calling agp_init+0x0/0x26 @ 1 > Linux agpgart interface v0.103 > initcall agp_init+0x0/0x26 returned 0 after 2792 usecs > calling agp_intel_init+0x0/0x29 @ 1 > initcall agp_intel_init+0x0/0x29 returned 0 after 111 usecs > calling agp_sis_init+0x0/0x29 @ 1 > initcall agp_sis_init+0x0/0x29 returned 0 after 133 usecs > calling agp_via_init+0x0/0x29 @ 1 > initcall agp_via_init+0x0/0x29 returned 0 after 101 usecs > calling init_tis+0x0/0x91 @ 1 > initcall init_tis+0x0/0x91 returned 0 after 65 usecs > calling cn_proc_init+0x0/0x3d @ 1 > initcall cn_proc_init+0x0/0x3d returned 0 after 45 usecs > calling serial8250_init+0x0/0x143 @ 1 > Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled > async_waiting @ 1 > async_continuing @ 1 after 10 usec > (XEN) irq.c:1139:d0 Cannot bind IRQ 4 to guest. In use by ''ns16550''. > (XEN) irq.c:1139:d0 Cannot bind IRQ 2 to guest. In use by ''cascade''. > (XEN) irq.c:1139:d0 Cannot bind IRQ 4 to guest. In use by ''ns16550''. > (XEN) irq.c:1139:d0 Cannot bind IRQ 2 to guest. In use by ''cascade''. > async_waiting @ 1 > async_continuing @ 1 after 1 usec > (XEN) irq.c:1139:d0 Cannot bind IRQ 4 to guest. In use by ''ns16550''. > (XEN) irq.c:1139:d0 Cannot bind IRQ 2 to guest. In use by ''cascade''. > (XEN) irq.c:1139:d0 Cannot bind IRQ 4 to guest. In use by ''ns16550''. > (XEN) irq.c:1139:d0 Cannot bind IRQ 2 to guest. In use by ''cascade''. > serial8250: ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A > initcall serial8250_init+0x0/0x143 returned 0 after 308270 usecs > calling serial8250_pnp_init+0x0/0x12 @ 1 > 00:0b: ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A > initcall serial8250_pnp_init+0x0/0x12 returned 0 after 5240 usecs > calling serial8250_pci_init+0x0/0x1b @ 1 > initcall serial8250_pci_init+0x0/0x1b returned 0 after 114 usecs > calling init_kgdboc+0x0/0x16 @ 1 > initcall init_kgdboc+0x0/0x16 returned 0 after 0 usecs > calling topology_sysfs_init+0x0/0x63 @ 1 > initcall topology_sysfs_init+0x0/0x63 returned 0 after 470 usecs > calling brd_init+0x0/0x16d @ 1 > brd: module loaded > initcall brd_init+0x0/0x16d returned 0 after 8259 usecs > calling loop_init+0x0/0x197 @ 1 > loop: module loaded > initcall loop_init+0x0/0x197 returned 0 after 4968 usecs > calling init_kgdbts+0x0/0x16 @ 1 > initcall init_kgdbts+0x0/0x16 returned 0 after 0 usecs > calling mac_hid_init+0x0/0xd5 @ 1 > input: Macintosh mouse button emulation as /devices/virtual/input/input2 > initcall mac_hid_init+0x0/0xd5 returned 0 after 6552 usecs > calling scsi_dh_init+0x0/0x3f @ 1 > initcall scsi_dh_init+0x0/0x3f returned 0 after 1 usecs > calling init_sd+0x0/0x17b @ 1 > initcall init_sd+0x0/0x17b returned 0 after 420 usecs > calling init_sr+0x0/0x49 @ 1 > initcall init_sr+0x0/0x49 returned 0 after 51 usecs > calling init_sg+0x0/0x123 @ 1 > initcall init_sg+0x0/0x123 returned 0 after 136 usecs > calling ahci_init+0x0/0x1b @ 1 > ahci 0000:00:1f.2: version 3.0 > xen: registering gsi 19 triggering 0 polarity 1 > alloc irq_desc for 19 on node 0 > alloc kstat_irqs on node 0 > xen: --> irq=19 > ahci 0000:00:1f.2: PCI INT B -> GSI 19 (level, low) -> IRQ 19 > alloc irq_desc for 4261 on node 0 > alloc kstat_irqs on node 0 > ahci: SSS flag set, parallel bus scan disabled > ahci 0000:00:1f.2: AHCI 0001.0200 32 slots 6 ports 3 Gbps 0x3f impl SATA > mode > ahci 0000:00:1f.2: flags: 64bit ncq sntf stag pm led clo pio slum part > ccc ems sxs > ahci 0000:00:1f.2: setting latency timer to 64 > scsi0 : ahci > scsi1 : ahci > scsi2 : ahci > scsi3 : ahci > scsi4 : ahci > scsi5 : ahci > ata1: SATA max UDMA/133 abar m2048@0xfbbd6000 port 0xfbbd6100 irq 4261 > ata2: SATA max UDMA/133 abar m2048@0xfbbd6000 port 0xfbbd6180 irq 4261 > ata3: SATA max UDMA/133 irq_stat 0x00400040, connection status changed > irq 4261 > ata4: SATA max UDMA/133 irq_stat 0x00400040, connection status changed > irq 4261 > ata5: SATA max UDMA/133 abar m2048@0xfbbd6000 port 0xfbbd6300 irq 4261 > ata6: SATA max UDMA/133 abar m2048@0xfbbd6000 port 0xfbbd6380 irq 4261 > calling 2_async_port_probe+0x0/0xc9 @ 233 > initcall ahci_init+0x0/0x1b returned 0 after 109920 usecs > calling piix_init+0x0/0x29 @ 1 > initcall piix_init+0x0/0x29 returned 0 after 136 usecs > calling fixed_mdio_bus_init+0x0/0xd0 @ 1 > Fixed MDIO Bus: probed > initcall fixed_mdio_bus_init+0x0/0xd0 returned 0 after 189 usecs > calling net_olddevs_init+0x0/0x9e @ 1 > initcall net_olddevs_init+0x0/0x9e returned 0 after 3 usecs > calling netif_init+0x0/0x6a @ 1 > initcall netif_init+0x0/0x6a returned 0 after 0 usecs > calling cdrom_init+0x0/0x6a @ 1 > initcall cdrom_init+0x0/0x6a returned 0 after 195 usecs > calling mon_init+0x0/0x117 @ 1 > initcall mon_init+0x0/0x117 returned 0 after 283 usecs > calling ehci_hcd_init+0x0/0xc0 @ 1 > ehci_hcd: USB 2.0 ''Enhanced'' Host Controller (EHCI) Driver > xen: registering gsi 18 triggering 0 polarity 1 > alloc irq_desc for 18 on node 0 > alloc kstat_irqs on node 0 > xen: --> irq=18 > ehci_hcd 0000:00:1a.7: PCI INT C -> GSI 18 (level, low) -> IRQ 18 > ehci_hcd 0000:00:1a.7: setting latency timer to 64 > ehci_hcd 0000:00:1a.7: EHCI Host Controller > ehci_hcd 0000:00:1a.7: new USB bus registered, assigned bus number 1 > ehci_hcd 0000:00:1a.7: debug port 1 > ehci_hcd 0000:00:1a.7: cache line size of 32 is not supported > ehci_hcd 0000:00:1a.7: irq 18, io mem 0xfbbde000 > ehci_hcd 0000:00:1a.7: USB 2.0 started, EHCI 1.00 > usb usb1: New USB device found, idVendor=1d6b, idProduct=0002 > usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1 > usb usb1: Product: EHCI Host Controller > usb usb1: Manufacturer: Linux 2.6.32.13 ehci_hcd > usb usb1: SerialNumber: 0000:00:1a.7 > usb usb1: configuration #1 chosen from 1 choice > hub 1-0:1.0: USB hub found > hub 1-0:1.0: 6 ports detected > xen: registering gsi 23 triggering 0 polarity 1 > alloc irq_desc for 23 on node 0 > alloc kstat_irqs on node 0 > xen: --> irq=23 > ehci_hcd 0000:00:1d.7: PCI INT A -> GSI 23 (level, low) -> IRQ 23 > ehci_hcd 0000:00:1d.7: setting latency timer to 64 > ehci_hcd 0000:00:1d.7: EHCI Host Controller > ehci_hcd 0000:00:1d.7: new USB bus registered, assigned bus number 2 > ehci_hcd 0000:00:1d.7: debug port 1 > ehci_hcd 0000:00:1d.7: cache line size of 32 is not supported > ehci_hcd 0000:00:1d.7: irq 23, io mem 0xfbbdc000 > ehci_hcd 0000:00:1d.7: USB 2.0 started, EHCI 1.00 > usb usb2: New USB device found, idVendor=1d6b, idProduct=0002 > usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1 > usb usb2: Product: EHCI Host Controller > usb usb2: Manufacturer: Linux 2.6.32.13 ehci_hcd > usb usb2: SerialNumber: 0000:00:1d.7 > usb usb2: configuration #1 chosen from 1 choice > hub 2-0:1.0: USB hub found > hub 2-0:1.0: 6 ports detected > initcall ehci_hcd_init+0x0/0xc0 returned 0 after 36306 usecs > calling ohci_hcd_mod_init+0x0/0x92 @ 1 > ohci_hcd: USB 1.1 ''Open'' Host Controller (OHCI) Driver > initcall ohci_hcd_mod_init+0x0/0x92 returned 0 after 121 usecs > calling uhci_hcd_init+0x0/0xc0 @ 1 > uhci_hcd: USB Universal Host Controller Interface driver > xen: registering gsi 16 triggering 0 polarity 1 > xen_allocate_pirq: returning irq 16 for gsi 16 > xen: --> irq=16 > Already setup the GSI :16 > uhci_hcd 0000:00:1a.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16 > uhci_hcd 0000:00:1a.0: setting latency timer to 64 > uhci_hcd 0000:00:1a.0: UHCI Host Controller > uhci_hcd 0000:00:1a.0: new USB bus registered, assigned bus number 3 > uhci_hcd 0000:00:1a.0: irq 16, io base 0x0000ac00 > usb usb3: New USB device found, idVendor=1d6b, idProduct=0001 > usb usb3: New USB device strings: Mfr=3, Product=2, SerialNumber=1 > usb usb3: Product: UHCI Host Controller > usb usb3: Manufacturer: Linux 2.6.32.13 uhci_hcd > usb usb3: SerialNumber: 0000:00:1a.0 > usb usb3: configuration #1 chosen from 1 choice > hub 3-0:1.0: USB hub found > hub 3-0:1.0: 2 ports detected > xen: registering gsi 21 triggering 0 polarity 1 > alloc irq_desc for 21 on node 0 > alloc kstat_irqs on node 0 > xen: --> irq=21 > uhci_hcd 0000:00:1a.1: PCI INT B -> GSI 21 (level, low) -> IRQ 21 > uhci_hcd 0000:00:1a.1: setting latency timer to 64 > uhci_hcd 0000:00:1a.1: UHCI Host Controller > uhci_hcd 0000:00:1a.1: new USB bus registered, assigned bus number 4 > uhci_hcd 0000:00:1a.1: irq 21, io base 0x0000a880 > usb usb4: New USB device found, idVendor=1d6b, idProduct=0001 > usb usb4: New USB device strings: Mfr=3, Product=2, SerialNumber=1 > usb usb4: Product: UHCI Host Controller > usb usb4: Manufacturer: Linux 2.6.32.13 uhci_hcd > usb usb4: SerialNumber: 0000:00:1a.1 > usb usb4: configuration #1 chosen from 1 choice > hub 4-0:1.0: USB hub found > hub 4-0:1.0: 2 ports detected > xen: registering gsi 19 triggering 0 polarity 1 > xen_allocate_pirq: returning irq 19 for gsi 19 > xen: --> irq=19 > Already setup the GSI :19 > uhci_hcd 0000:00:1a.2: PCI INT D -> GSI 19 (level, low) -> IRQ 19 > uhci_hcd 0000:00:1a.2: setting latency timer to 64 > uhci_hcd 0000:00:1a.2: UHCI Host Controller > uhci_hcd 0000:00:1a.2: new USB bus registered, assigned bus number 5 > uhci_hcd 0000:00:1a.2: irq 19, io base 0x0000a800 > usb usb5: New USB device found, idVendor=1d6b, idProduct=0001 > usb usb5: New USB device strings: Mfr=3, Product=2, SerialNumber=1 > usb usb5: Product: UHCI Host Controller > usb usb5: Manufacturer: Linux 2.6.32.13 uhci_hcd > usb usb5: SerialNumber: 0000:00:1a.2 > usb usb5: configuration #1 chosen from 1 choice > hub 5-0:1.0: USB hub found > hub 5-0:1.0: 2 ports detected > xen: registering gsi 23 triggering 0 polarity 1 > xen_allocate_pirq: returning irq 23 for gsi 23 > xen: --> irq=23 > Already setup the GSI :23 > uhci_hcd 0000:00:1d.0: PCI INT A -> GSI 23 (level, low) -> IRQ 23 > uhci_hcd 0000:00:1d.0: setting latency timer to 64 > uhci_hcd 0000:00:1d.0: UHCI Host Controller > uhci_hcd 0000:00:1d.0: new USB bus registered, assigned bus number 6 > uhci_hcd 0000:00:1d.0: irq 23, io base 0x0000a480 > usb usb6: New USB device found, idVendor=1d6b, idProduct=0001 > usb usb6: New USB device strings: Mfr=3, Product=2, SerialNumber=1 > usb usb6: Product: UHCI Host Controller > usb usb6: Manufacturer: Linux 2.6.32.13 uhci_hcd > usb usb6: SerialNumber: 0000:00:1d.0 > usb usb6: configuration #1 chosen from 1 choice > hub 6-0:1.0: USB hub found > hub 6-0:1.0: 2 ports detected > xen: registering gsi 19 triggering 0 polarity 1 > xen_allocate_pirq: returning irq 19 for gsi 19 > xen: --> irq=19 > Already setup the GSI :19 > uhci_hcd 0000:00:1d.1: PCI INT B -> GSI 19 (level, low) -> IRQ 19 > uhci_hcd 0000:00:1d.1: setting latency timer to 64 > uhci_hcd 0000:00:1d.1: UHCI Host Controller > uhci_hcd 0000:00:1d.1: new USB bus registered, assigned bus number 7 > uhci_hcd 0000:00:1d.1: irq 19, io base 0x0000a400 > usb usb7: New USB device found, idVendor=1d6b, idProduct=0001 > usb usb7: New USB device strings: Mfr=3, Product=2, SerialNumber=1 > usb usb7: Product: UHCI Host Controller > usb usb7: Manufacturer: Linux 2.6.32.13 uhci_hcd > usb usb7: SerialNumber: 0000:00:1d.1 > usb usb7: configuration #1 chosen from 1 choice > hub 7-0:1.0: USB hub found > hub 7-0:1.0: 2 ports detected > xen: registering gsi 18 triggering 0 polarity 1 > xen_allocate_pirq: returning irq 18 for gsi 18 > xen: --> irq=18 > Already setup the GSI :18 > uhci_hcd 0000:00:1d.2: PCI INT C -> GSI 18 (level, low) -> IRQ 18 > uhci_hcd 0000:00:1d.2: setting latency timer to 64 > uhci_hcd 0000:00:1d.2: UHCI Host Controller > uhci_hcd 0000:00:1d.2: new USB bus registered, assigned bus number 8 > uhci_hcd 0000:00:1d.2: irq 18, io base 0x0000a080 > usb usb8: New USB device found, idVendor=1d6b, idProduct=0001 > usb usb8: New USB device strings: Mfr=3, Product=2, SerialNumber=1 > usb usb8: Product: UHCI Host Controller > usb usb8: Manufacturer: Linux 2.6.32.13 uhci_hcd > usb usb8: SerialNumber: 0000:00:1d.2 > usb usb8: configuration #1 chosen from 1 choice > hub 8-0:1.0: USB hub found > hub 8-0:1.0: 2 ports detected > initcall uhci_hcd_init+0x0/0xc0 returned 0 after 27682 usecs > calling i8042_init+0x0/0x3a7 @ 1 > PNP: No PS/2 controller found. Probing ports directly. > serio: i8042 KBD port at 0x60,0x64 irq 1 > serio: i8042 AUX port at 0x60,0x64 irq 12 > initcall i8042_init+0x0/0x3a7 returned 0 after 3611 usecs > calling serport_init+0x0/0x34 @ 1 > initcall serport_init+0x0/0x34 returned 0 after 1 usecs > calling mousedev_init+0x0/0x62 @ 1 > mice: PS/2 mouse device common for all mice > initcall mousedev_init+0x0/0x62 returned 0 after 614 usecs > calling evdev_init+0x0/0x12 @ 1 > initcall evdev_init+0x0/0x12 returned 0 after 447 usecs > calling atkbd_init+0x0/0x27 @ 1 > initcall atkbd_init+0x0/0x27 returned 0 after 105 usecs > calling psmouse_init+0x0/0x74 @ 1 > initcall psmouse_init+0x0/0x74 returned 0 after 442 usecs > calling xenkbd_init+0x0/0x5d @ 1 > initcall xenkbd_init+0x0/0x5d returned -19 after 0 usecs > calling cmos_init+0x0/0x6d @ 1 > rtc_cmos 00:03: RTC can wake from S4 > rtc_cmos 00:03: rtc core: registered rtc_cmos as rtc0 > rtc0: alarms up to one month, y3k, 114 bytes nvram > initcall cmos_init+0x0/0x6d returned 0 after 619 usecs > calling dm_init+0x0/0x49 @ 1 > device-mapper: uevent: version 1.0.3 > device-mapper: ioctl: 4.15.0-ioctl (2009-04-01) initialised: > dm-devel@redhat.com > initcall dm_init+0x0/0x49 returned 0 after 1824 usecs > calling dm_snapshot_init+0x0/0x26a @ 1 > initcall dm_snapshot_init+0x0/0x26a returned 0 after 898 usecs > calling dm_mirror_init+0x0/0x79 @ 1 > initcall dm_mirror_init+0x0/0x79 returned 0 after 252 usecs > calling dm_dirty_log_init+0x0/0x59 @ 1 > initcall dm_dirty_log_init+0x0/0x59 returned 0 after 16 usecs > calling dm_zero_init+0x0/0x31 @ 1 > initcall dm_zero_init+0x0/0x31 returned 0 after 1 usecs > calling init_ladder+0x0/0x12 @ 1 > cpuidle: using governor ladder > initcall init_ladder+0x0/0x12 returned 0 after 19 usecs > calling init_menu+0x0/0x12 @ 1 > cpuidle: using governor menu > initcall init_menu+0x0/0x12 returned 0 after 2 usecs > calling efivars_init+0x0/0x213 @ 1 > initcall efivars_init+0x0/0x213 returned -19 after 0 usecs > calling hid_init+0x0/0x66 @ 1 > initcall hid_init+0x0/0x66 returned 0 after 175 usecs > calling a4_init+0x0/0x1b @ 1 > initcall a4_init+0x0/0x1b returned 0 after 68 usecs > calling apple_init+0x0/0x38 @ 1 > initcall apple_init+0x0/0x38 returned 0 after 84 usecs > calling belkin_init+0x0/0x1b @ 1 > initcall belkin_init+0x0/0x1b returned 0 after 65 usecs > calling ch_init+0x0/0x1b @ 1 > initcall ch_init+0x0/0x1b returned 0 after 59 usecs > calling ch_init+0x0/0x1b @ 1 > initcall ch_init+0x0/0x1b returned 0 after 69 usecs > calling cp_init+0x0/0x1b @ 1 > initcall cp_init+0x0/0x1b returned 0 after 65 usecs > calling dr_init+0x0/0x1b @ 1 > initcall dr_init+0x0/0x1b returned 0 after 56 usecs > calling ez_init+0x0/0x1b @ 1 > initcall ez_init+0x0/0x1b returned 0 after 57 usecs > calling gyration_init+0x0/0x1b @ 1 > initcall gyration_init+0x0/0x1b returned 0 after 52 usecs > calling ks_init+0x0/0x1b @ 1 > initcall ks_init+0x0/0x1b returned 0 after 98 usecs > calling kye_init+0x0/0x1b @ 1 > initcall kye_init+0x0/0x1b returned 0 after 60 usecs > calling lg_init+0x0/0x1b @ 1 > initcall lg_init+0x0/0x1b returned 0 after 73 usecs > calling ms_init+0x0/0x1b @ 1 > initcall ms_init+0x0/0x1b returned 0 after 68 usecs > calling mr_init+0x0/0x1b @ 1 > initcall mr_init+0x0/0x1b returned 0 after 64 usecs > calling ntrig_init+0x0/0x1b @ 1 > initcall ntrig_init+0x0/0x1b returned 0 after 72 usecs > calling pl_init+0x0/0x1b @ 1 > initcall pl_init+0x0/0x1b returned 0 after 64 usecs > calling pl_init+0x0/0x1b @ 1 > initcall pl_init+0x0/0x1b returned 0 after 71 usecs > calling samsung_init+0x0/0x1b @ 1 > initcall samsung_init+0x0/0x1b returned 0 after 59 usecs > calling sjoy_init+0x0/0x1b @ 1 > initcall sjoy_init+0x0/0x1b returned 0 after 64 usecs > calling sony_init+0x0/0x1b @ 1 > initcall sony_init+0x0/0x1b returned 0 after 70 usecs > calling sp_init+0x0/0x1b @ 1 > initcall sp_init+0x0/0x1b returned 0 after 57 usecs > calling ga_init+0x0/0x1b @ 1 > initcall ga_init+0x0/0x1b returned 0 after 52 usecs > calling tm_init+0x0/0x1b @ 1 > initcall tm_init+0x0/0x1b returned 0 after 52 usecs > calling ts_init+0x0/0x1b @ 1 > initcall ts_init+0x0/0x1b returned 0 after 57 usecs > calling twinhan_init+0x0/0x1b @ 1 > initcall twinhan_init+0x0/0x1b returned 0 after 85 usecs > calling zp_init+0x0/0x1b @ 1 > initcall zp_init+0x0/0x1b returned 0 after 70 usecs > calling hid_init+0x0/0xcb @ 1 > usbcore: registered new interface driver hiddev > usbcore: registered new interface driver usbhid > usbhid: v2.6:USB HID core driver > initcall hid_init+0x0/0xcb returned 0 after 446 usecs > calling flow_cache_init+0x0/0x1b0 @ 1 > initcall flow_cache_init+0x0/0x1b0 returned 0 after 350 usecs > calling blackhole_module_init+0x0/0x12 @ 1 > initcall blackhole_module_init+0x0/0x12 returned 0 after 2 usecs > calling init_cgroup_cls+0x0/0x12 @ 1 > initcall init_cgroup_cls+0x0/0x12 returned 0 after 21 usecs > calling nf_conntrack_standalone_init+0x0/0x12 @ 1 > nf_conntrack version 0.5.0 (16384 buckets, 65536 max) > CONFIG_NF_CT_ACCT is deprecated and will be removed soon. Please use > nf_conntrack.acct=1 kernel parameter, acct=1 nf_conntrack module option > or > sysctl net.netfilter.nf_conntrack_acct=1 to enable it. > initcall nf_conntrack_standalone_init+0x0/0x12 returned 0 after 22301 > usecs > calling xt_init+0x0/0x190 @ 1 > initcall xt_init+0x0/0x190 returned 0 after 42 usecs > calling tcpudp_mt_init+0x0/0x17 @ 1 > initcall tcpudp_mt_init+0x0/0x17 returned 0 after 25 usecs > calling conntrack_mt_init+0x0/0x17 @ 1 > initcall conntrack_mt_init+0x0/0x17 returned 0 after 2 usecs > calling state_mt_init+0x0/0x17 @ 1 > initcall state_mt_init+0x0/0x17 returned 0 after 2 usecs > calling sysctl_ipv4_init+0x0/0x4e @ 1 > initcall sysctl_ipv4_init+0x0/0x4e returned 0 after 2354 usecs > calling init_syncookies+0x0/0x19 @ 1 > initcall init_syncookies+0x0/0x19 returned 0 after 44 usecs > calling ipv4_netfilter_init+0x0/0x17 @ 1 > initcall ipv4_netfilter_init+0x0/0x17 returned 0 after 16 usecs > calling nf_conntrack_l3proto_ipv4_init+0x0/0x12d @ 1 > initcall nf_conntrack_l3proto_ipv4_init+0x0/0x12d returned 0 after 506 > usecs > calling nf_defrag_init+0x0/0x17 @ 1 > initcall nf_defrag_init+0x0/0x17 returned 0 after 2 usecs > calling ip_tables_init+0x0/0xaf @ 1 > ip_tables: (C) 2000-2006 Netfilter Core Team > initcall ip_tables_init+0x0/0xaf returned 0 after 44 usecs > calling iptable_filter_init+0x0/0x6c @ 1 > initcall iptable_filter_init+0x0/0x6c returned 0 after 136 usecs > calling reject_tg_init+0x0/0x12 @ 1 > initcall reject_tg_init+0x0/0x12 returned 0 after 3 usecs > calling cubictcp_register+0x0/0x65 @ 1 > TCP cubic registered > initcall cubictcp_register+0x0/0x65 returned 0 after 3 usecs > calling xfrm_user_init+0x0/0x4d @ 1 > Initializing XFRM netlink socket > initcall xfrm_user_init+0x0/0x4d returned 0 after 49 usecs > calling packet_init+0x0/0x47 @ 1 > NET: Registered protocol family 17 > initcall packet_init+0x0/0x47 returned 0 after 45 usecs > calling dsa_init_module+0x0/0x14 @ 1 > initcall dsa_init_module+0x0/0x14 returned 0 after 1 usecs > calling edsa_init_module+0x0/0x14 @ 1 > initcall edsa_init_module+0x0/0x14 returned 0 after 1 usecs > calling trailer_init_module+0x0/0x14 @ 1 > initcall trailer_init_module+0x0/0x14 returned 0 after 1 usecs > calling mv88e6060_init+0x0/0x14 @ 1 > initcall mv88e6060_init+0x0/0x14 returned 0 after 14 usecs > calling mv88e6123_61_65_init+0x0/0x14 @ 1 > initcall mv88e6123_61_65_init+0x0/0x14 returned 0 after 1 usecs > calling mv88e6131_init+0x0/0x14 @ 1 > initcall mv88e6131_init+0x0/0x14 returned 0 after 1 usecs > calling dsa_init_module+0x0/0x12 @ 1 > initcall dsa_init_module+0x0/0x12 returned 0 after 73 usecs > calling dcbnl_init+0x0/0x32 @ 1 > initcall dcbnl_init+0x0/0x32 returned 0 after 0 usecs > calling mce_debugfs_init+0x0/0x3b @ 1 > initcall mce_debugfs_init+0x0/0x3b returned 0 after 46 usecs > calling severities_debugfs_init+0x0/0x3b @ 1 > initcall severities_debugfs_init+0x0/0x3b returned 0 after 18 usecs > calling hpet_insert_resource+0x0/0x23 @ 1 > initcall hpet_insert_resource+0x0/0x23 returned 0 after 3 usecs > calling update_mp_table+0x0/0x689 @ 1 > initcall update_mp_table+0x0/0x689 returned 0 after 0 usecs > calling lapic_insert_resource+0x0/0x40 @ 1 > initcall lapic_insert_resource+0x0/0x40 returned -1 after 0 usecs > initcall lapic_insert_resource+0x0/0x40 returned with error code -1 > calling init_lapic_nmi_sysfs+0x0/0x39 @ 1 > initcall init_lapic_nmi_sysfs+0x0/0x39 returned 0 after 0 usecs > calling io_apic_bug_finalize+0x0/0x1b @ 1 > initcall io_apic_bug_finalize+0x0/0x1b returned 0 after 0 usecs > calling check_early_ioremap_leak+0x0/0x67 @ 1 > initcall check_early_ioremap_leak+0x0/0x67 returned 0 after 0 usecs > calling pat_memtype_list_init+0x0/0x29 @ 1 > initcall pat_memtype_list_init+0x0/0x29 returned 0 after 19 usecs > calling sched_init_debug+0x0/0x24 @ 1 > initcall sched_init_debug+0x0/0x24 returned 0 after 18 usecs > calling init_oops_id+0x0/0x36 @ 1 > initcall init_oops_id+0x0/0x36 returned 0 after 8 usecs > calling disable_boot_consoles+0x0/0x5c @ 1 > initcall disable_boot_consoles+0x0/0x5c returned 0 after 0 usecs > calling pm_qos_power_init+0x0/0xca @ 1 > initcall pm_qos_power_init+0x0/0xca returned 0 after 352 usecs > calling test_suspend+0x0/0x19d @ 1 > initcall test_suspend+0x0/0x19d returned 0 after 0 usecs > calling software_resume+0x0/0x20f @ 1 > PM: Resume from disk failed. > initcall software_resume+0x0/0x20f returned -2 after 15 usecs > initcall software_resume+0x0/0x20f returned with error code -2 > calling debugfs_kprobe_init+0x0/0x8e @ 1 > initcall debugfs_kprobe_init+0x0/0x8e returned 0 after 111 usecs > calling taskstats_init+0x0/0x95 @ 1 > registered taskstats version 1 > initcall taskstats_init+0x0/0x95 returned 0 after 35 usecs > calling clear_boot_tracer+0x0/0x2d @ 1 > initcall clear_boot_tracer+0x0/0x2d returned 0 after 0 usecs > calling fail_page_alloc_debugfs+0x0/0xe4 @ 1 > initcall fail_page_alloc_debugfs+0x0/0xe4 returned 0 after 193 usecs > calling max_swapfiles_check+0x0/0x8 @ 1 > initcall max_swapfiles_check+0x0/0x8 returned 0 after 0 usecs > calling failslab_debugfs_init+0x0/0x6b @ 1 > initcall failslab_debugfs_init+0x0/0x6b returned 0 after 135 usecs > calling init_ima+0x0/0x1a @ 1 > No TPM chip found, activating TPM-bypass! > initcall init_ima+0x0/0x1a returned 0 after 615 usecs > calling fail_make_request_debugfs+0x0/0x19 @ 1 > initcall fail_make_request_debugfs+0x0/0x19 returned 0 after 306 usecs > calling random32_reseed+0x0/0xa9 @ 1 > initcall random32_reseed+0x0/0xa9 returned 0 after 147 usecs > calling pci_resource_alignment_sysfs_init+0x0/0x19 @ 1 > initcall pci_resource_alignment_sysfs_init+0x0/0x19 returned 0 after 6 > usecs > calling pci_sysfs_init+0x0/0x4c @ 1 > initcall pci_sysfs_init+0x0/0x4c returned 0 after 3427 usecs > calling boot_wait_for_devices+0x0/0x19 @ 1 > initcall boot_wait_for_devices+0x0/0x19 returned 0 after 1 usecs > calling regulator_init_complete+0x0/0x14b @ 1 > initcall regulator_init_complete+0x0/0x14b returned 0 after 16 usecs > calling seqgen_init+0x0/0xf @ 1 > initcall seqgen_init+0x0/0xf returned 0 after 46 usecs > calling late_resume_init+0x0/0x124 @ 1 > Magic number: 10:134:278 > tty tty15: hash matches > initcall late_resume_init+0x0/0x124 returned 0 after 92 usecs > calling scsi_complete_async_scans+0x0/0x148 @ 1 > initcall scsi_complete_async_scans+0x0/0x148 returned 0 after 0 usecs > calling rtc_hctosys+0x0/0x152 @ 1 > usb 2-1: new high speed USB device using ehci_hcd and address 2 > usb 2-1: New USB device found, idVendor=2001, idProduct=f103 > usb 2-1: New USB device strings: Mfr=0, Product=0, SerialNumber=0 > usb 2-1: configuration #1 chosen from 1 choice > hub 2-1:1.0: USB hub found > hub 2-1:1.0: 7 ports detected > usb 2-1.2: new full speed USB device using ehci_hcd and address 4 > usb 2-1.2: New USB device found, idVendor=04e8, idProduct=326c > usb 2-1.2: New USB device strings: Mfr=1, Product=2, SerialNumber=3 > usb 2-1.2: Product: Samsung ML-2010 > usb 2-1.2: Manufacturer: Samsung > usb 2-1.2: SerialNumber: 3A61BKCL919879R. > usb 2-1.2: configuration #1 chosen from 1 choice > usb 6-2: new low speed USB device using uhci_hcd and address 2 > usb 6-2: New USB device found, idVendor=05af, idProduct=0408 > usb 6-2: New USB device strings: Mfr=0, Product=2, SerialNumber=0 > usb 6-2: Product: 2.4G USB RF KeyBoard > usb 6-2: configuration #1 chosen from 1 choice > input: 2.4G USB RF KeyBoard > as /devices/pci0000:00/0000:00:1d.0/usb6/6-2/6-2:1.0/input/input3 > generic-usb 0003:05AF:0408.0001: input,hidraw0: USB HID v1.10 Keyboard > [2.4G USB RF KeyBoard] on usb-0000:00:1d.0-2/input0 > input: 2.4G USB RF KeyBoard > as /devices/pci0000:00/0000:00:1d.0/usb6/6-2/6-2:1.1/input/input4 > generic-usb 0003:05AF:0408.0002: input,hidraw1: USB HID v1.10 Mouse > [2.4G USB RF KeyBoard] on usb-0000:00:1d.0-2/input1 > input: 2.4G USB RF KeyBoard > as /devices/pci0000:00/0000:00:1d.0/usb6/6-2/6-2:1.2/input/input5 > rtc_cmos 00:03: setting system clock to 2010-05-30 11:17:51 UTC > (1275218271) > initcall rtc_hctosys+0x0/0x152 returned 0 after 1682629 usecs > calling memmap_init+0x0/0xa3 @ 1 > calling 3_async_port_probe+0x0/0xc9 @ 261 > generic-usb 0003:05AF:0408.0003: input,hiddev96,hidraw2: USB HID v1.10 > Device [2.4G USB RF KeyBoard] on usb-0000:00:1d.0-2/input2 > initcall memmap_init+0x0/0xa3 returned 0 after 811 usecs > calling pci_mmcfg_late_insert_resources+0x0/0x163 @ 1 > initcall pci_mmcfg_late_insert_resources+0x0/0x163 returned 0 after 8 > usecs > calling init_net_drop_monitor+0x0/0x17e @ 1 > Initalizing network drop monitor service > initcall init_net_drop_monitor+0x0/0x17e returned 0 after 290 usecs > calling tcp_congestion_default+0x0/0x12 @ 1 > initcall tcp_congestion_default+0x0/0x12 returned 0 after 1 usecs > calling initialize_hashrnd+0x0/0x19 @ 1 > initcall initialize_hashrnd+0x0/0x19 returned 0 after 7 usecs > async_waiting @ 1 > async_waiting @ 261 > calling 4_async_port_probe+0x0/0xc9 @ 262 > calling 5_async_port_probe+0x0/0xc9 @ 263 > async_waiting @ 263 > calling 6_async_port_probe+0x0/0xc9 @ 264 > async_waiting @ 264 > calling 7_async_port_probe+0x0/0xc9 @ 265 > async_waiting @ 265 > async_waiting @ 262 > ata1: SATA link down (SStatus 0 SControl 300) > async_waiting @ 233 > async_continuing @ 233 after 3 usec > initcall 2_async_port_probe+0x0/0xc9 returned 0 after 313154 usecs > async_continuing @ 261 after 236544 usec > ata2: SATA link down (SStatus 0 SControl 300) > async_waiting @ 261 > async_continuing @ 261 after 1 usec > initcall 3_async_port_probe+0x0/0xc9 returned 0 after 555507 usecs > async_continuing @ 262 after 536879 usec > ata3: SATA link up 3.0 Gbps (SStatus 123 SControl 300) > ata3.00: ATA-8: WDC WD7501AALS-00J7B1, 05.00K05, max UDMA/133 > ata3.00: 1465149168 sectors, multi 0: LBA48 NCQ (depth 31/32), AA > ata3.00: configured for UDMA/133 > async_waiting @ 262 > async_continuing @ 262 after 1 usec > scsi 2:0:0:0: Direct-Access ATA WDC WD7501AALS-0 05.0 PQ: 0 > ANSI: 5 > calling 8_sd_probe_async+0x0/0x1e3 @ 261 > sd 2:0:0:0: Attached scsi generic sg0 type 0 > initcall 4_async_port_probe+0x0/0xc9 returned 0 after 1292146 usecs > async_continuing @ 263 after 1312855 usec > sd 2:0:0:0: [sda] 1465149168 512-byte logical blocks: (750 GB/698 GiB) > sd 2:0:0:0: [sda] Write Protect is off > sd 2:0:0:0: [sda] Mode Sense: 00 3a 00 00 > sd 2:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn''t > support DPO or FUA > sda: sda1 sda2 sda3 > sd 2:0:0:0: [sda] Attached SCSI disk > initcall 8_sd_probe_async+0x0/0x1e3 returned 0 after 38221 usecs > ata4: SATA link up 1.5 Gbps (SStatus 113 SControl 300) > ata4.00: ATAPI: HL-DT-STDVD-RAM GH22NS30, 1.01, max UDMA/100 > ata4.00: configured for UDMA/100 > async_waiting @ 263 > async_continuing @ 263 after 2 usec > scsi 3:0:0:0: CD-ROM HL-DT-ST DVD-RAM GH22NS30 1.01 PQ: 0 > ANSI: 5 > sr0: scsi3-mmc drive: 48x/48x writer dvd-ram cd/rw xa/form2 cdda tray > Uniform CD-ROM driver Revision: 3.20 > sr 3:0:0:0: Attached scsi CD-ROM sr0 > sr 3:0:0:0: Attached scsi generic sg1 type 5 > initcall 5_async_port_probe+0x0/0xc9 returned 0 after 2200976 usecs > async_continuing @ 264 after 2206705 usec > async/2 used greatest stack depth: 4248 bytes left > ata5: SATA link down (SStatus 0 SControl 300) > async_waiting @ 264 > async_continuing @ 264 after 1 usec > initcall 6_async_port_probe+0x0/0xc9 returned 0 after 2523975 usecs > async_continuing @ 265 after 2529786 usec > ata6: SATA link down (SStatus 0 SControl 300) > async_waiting @ 265 > async_continuing @ 265 after 1 usec > initcall 7_async_port_probe+0x0/0xc9 returned 0 after 2847040 usecs > async_continuing @ 1 after 2919764 usec > Freeing unused kernel memory: 3380k freed > Write protecting the kernel read-only data: 7004k > mLoading, please wait... > calling i2c_init+0x0/0x70 [i2c_core] @ 297 > initcall i2c_init+0x0/0x70 [i2c_core] returned 0 after 220 usecs > calling nvidiafb_init+0x0/0x25 [nvidiafb] @ 297 > nvidiafb 0000:01:00.0: enabling device (0140 -> 0143) > xen: registering gsi 16 triggering 0 polarity 1 > xen_allocate_pirq: returning irq 16 for gsi 16 > xen: --> irq=16 > Already setup the GSI :16 > nvidiafb 0000:01:00.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16 > nvidiafb: Device ID: 10de042f > nvidiafb: unknown NV_ARCH > xen: registering gsi 16 triggering 0 polarity 1 > xen_allocate_pirq: returning irq 16 for gsi 16 > xen: --> irq=16 > Already setup the GSI :16 > nvidiafb 0000:03:00.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16 > nvidiafb: Device ID: 10de06fd > nvidiafb: unknown NV_ARCH > initcall nvidiafb_init+0x0/0x25 [nvidiafb] returned 0 after 67706 usecs > calling megasas_init+0x0/0x16f [megaraid_sas] @ 666 > megasas: 00.00.04.01 Thu July 24 11:41:51 PST 2008 > megasas: 0x1028:0x0015:0x1028:0x1f03: bus 5:slot 14:func 0 > xen: registering gsi 18 triggering 0 polarity 1 > xen_allocate_pirq: returning irq 18 for gsi 18 > xen: --> irq=18 > Already setup the GSI :18 > megaraid_sas 0000:05:0e.0: PCI INT A -> GSI 18 (level, low) -> IRQ 18 > megasas: FW now in Ready state > calling e1000_init_module+0x0/0(XEN) [VT-D]iommu.c:821: > iommu_fault_status: Primary Pending Fault > x70 [e1000e] @ 6(XEN) [VT-D]iommu.c:796: DMAR:[DMA Write] Request device > [05:08.0] fault addr 2d0842000, iommu reg = ffff82c3fff57000 > (XEN) DMAR:[fault reason 02h] Present bit in context entry is clear > 76 > (XEN) print_vtd_entries: iommu = ffff83013ff7b130 bdf = 5:8.0 gmfn > 2d0842 > scsi6 : LSI SAS (XEN) root_entry = ffff83013ff37000 > based MegaRAID d(XEN) root_entry[5] = 13cf13001 > river > (XEN) context = ffff83013cf13000 > initcall megasas(XEN) context[40] = 0_0 > _init+0x0/0x16f (XEN) ctxt_entry[40] not present > [megaraid_sas] r(XEN) [VT-D]iommu.c:821: iommu_fault_status: Primary > Pending Fault > eturned 0 after (XEN) [VT-D]iommu.c:796: DMAR:[DMA Write] Request device > [05:08.0] fault addr 2d0842000, iommu reg = ffff82c3fff57000 > (XEN) DMAR:[fault reason 02h] Present bit in context entry is clear > 73201 usecs > (XEN) print_vtd_entries: iommu = ffff83013ff7b130 bdf = 5:8.0 gmfn > 2d0842 > scsi scan: INQUI(XEN) root_entry = ffff83013ff37000 > RY result too sh(XEN) root_entry[5] = 13cf13001 > ort (5), using 3(XEN) context = ffff83013cf13000 > 6 > (XEN) context[40] = 0_0 > scsi 6:0:0:0: Di(XEN) ctxt_entry[40] not present > rect-Access PQ: 0 ANSI: 0 > scsi scan: INQUIRY result too short (5), using 36 > scsi 6:0:1:0: Direct-Access PQ: 0 > ANSI: 0 > scsi scan: INQUIRY result too short (5), using 36 > scsi 6:0:2:0: Direct-Access PQ: 0 > ANSI: 0 > scsi scan: INQUIRY result too short (5), using 36 > scsi 6:0:3:0: Direct-Access PQ: 0 > ANSI: 0 > scsi 6:2:0:0: Direct-Access DELL PERC 5/i 1.03 PQ: 0 > ANSI: 5 > e1000e: Intel(R) PRO/1000 Network Driver - 1.0.2-k2 > e1000e: Copyright (c) 1999-2008 Intel Corporation. > e1000e 0000:07:00.0: Disabling L1 ASPM > xen: registering gsi 16 triggering 0 polarity 1 > xen_allocate_pirq: returning irq 16 for gsi 16 > xen: --> irq=16 > Already setup the GSI :16 > e1000e 0000:07:00.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16 > e1000e 0000:07:00.0: setting latency timer to 64 > alloc irq_desc for 4260 on node 0 > alloc kstat_irqs on node 0 > alloc irq_desc for 4259 on node 0 > alloc kstat_irqs on node 0 > alloc irq_desc for 4258 on node 0 > sd 6:2:0:0: Attached scsi generic sg2 type 0 > scsi_scan_6 used(XEN) [VT-D]iommu.c:821: iommu_fault_status: Primary > Pending Fault > greatest stack (XEN) [VT-D]iommu.c:796: DMAR:[DMA Write] Request device > [05:08.0] fault addr 2cfa6e000, iommu reg = ffff82c3fff57000 > (XEN) DMAR:[fault reason 02h] Present bit in context entry is clear > depth: 4088 byte(XEN) print_vtd_entries: iommu = ffff83013ff7b130 bdf > 5:8.0 gmfn = 2cfa6e > s left > (XEN) root_entry = ffff83013ff37000 > sd 6:2:0:0: [sdb(XEN) root_entry[5] = 13cf13001 > ] 211550208 512-(XEN) context = ffff83013cf13000 > byte logical blo(XEN) context[40] = 0_0 > cks: (108 GB/100(XEN) ctxt_entry[40] not present > GiB) > sd 6:2:0:0: [sdb] Write Protect is off > sd 6:2:0:0: [sdb] Mode Sense: 1f 00 00 08 > sd 6:2:0:0: [sdb] Write cache: disabled, read cache: enabled, doesn''t > support DPO or FUA > sdb: unknown partition table > alloc kstat_irqs on node 0 > sd 6:2:0:0: [sdb] Attached SCSI disk > 0000:07:00.0: eth0: (PCI Express:2.5GB/s:Width x1) 00:30:48:b8:de:18 > 0000:07:00.0: eth0: Intel(R) PRO/1000 Network Connection > 0000:07:00.0: eth0: MAC: 3, PHY: 8, PBA No: 0101ff-0ff > e1000e 0000:08:00.0: Disabling L1 ASPM > xen: registering gsi 17 triggering 0 polarity 1 > xen_allocate_pirq: returning irq 17 for gsi 17 > xen: --> irq=17 > Already setup the GSI :17 > e1000e 0000:08:00.0: PCI INT A -> GSI 17 (level, low) -> IRQ 17 > e1000e 0000:08:00.0: setting latency timer to 64 > alloc irq_desc for 4257 on node 0 > alloc kstat_irqs on node 0 > alloc irq_desc for 4256 on node 0 > alloc kstat_irqs on node 0 > alloc irq_desc for 4255 on node 0 > alloc kstat_irqs on node 0 > scsi_id used greatest stack depth: 3904 bytes left > 0000:08:00.0: eth1: (PCI Express:2.5GB/s:Width x1) 00:30:48:b8:de:19 > 0000:08:00.0: eth1: Intel(R) PRO/1000 Network Connection > 0000:08:00.0: eth1: MAC: 3, PHY: 8, PBA No: 0101ff-0ff > initcall e1000_init_module+0x0/0x70 [e1000e] returned 0 after 392599 > usecs > (XEN) [VT-D]iommu.c:821: iommu_fault_status: Primary Pending Fault > (XEN) [VT-D]iommu.c:796: DMAR:[DMA Write] Request device [05:08.0] fault > addr 2cede1000, iommu reg = ffff82c3fff57000 > (XEN) DMAR:[fault reason 02h] Present bit in context entry is clear > (XEN) print_vtd_entries: iommu = ffff83013ff7b130 bdf = 5:8.0 gmfn > 2cede1 > (XEN) root_entry = ffff83013ff37000 > (XEN) root_entry[5] = 13cf13001 > (XEN) context = ffff83013cf13000 > (XEN) context[40] = 0_0 > (XEN) ctxt_entry[40] not present > (XEN) [VT-D]iommu.c:821: iommu_fault_status: Primary Pending Fault > (XEN) [VT-D]iommu.c:796: DMAR:[DMA Write] Request device [05:08.0] fault > addr 2cede3000, iommu reg = ffff82c3fff57000 > (XEN) DMAR:[fault reason 02h] Present bit in context entry is clear > (XEN) print_vtd_entries: iommu = ffff83013ff7b130 bdf = 5:8.0 gmfn > 2cede3 > (XEN) root_entry = ffff83013ff37000 > (XEN) root_entry[5] = 13cf13001 > (XEN) context = ffff83013cf13000 > (XEN) context[40] = 0_0 > (XEN) ctxt_entry[40] not present > (XEN) [VT-D]iommu.c:821: iommu_fault_status: Primary Pending Fault > (XEN) [VT-D]iommu.c:796: DMAR:[DMA Write] Request device [05:08.0] fault > addr 2cede2000, iommu reg = ffff82c3fff57000 > (XEN) DMAR:[fault reason 02h] Present bit in context entry is clear > (XEN) print_vtd_entries: iommu = ffff83013ff7b130 bdf = 5:8.0 gmfn > 2cede2 > (XEN) root_entry = ffff83013ff37000 > (XEN) root_entry[5] = 13cf13001 > (XEN) context = ffff83013cf13000 > (XEN) context[40] = 0_0 > (XEN) ctxt_entry[40] not present > (XEN) [VT-D]iommu.c:821: iommu_fault_status: Primary Pending Fault > (XEN) [VT-D]iommu.c:796: DMAR:[DMA Write] Request device [05:08.0] fault > addr 2cfff9000, iommu reg = ffff82c3fff57000 > (XEN) DMAR:[fault reason 02h] Present bit in context entry is clear > (XEN) print_vtd_entries: iommu = ffff83013ff7b130 bdf = 5:8.0 gmfn > 2cfff9 > (XEN) root_entry = ffff83013ff37000 > (XEN) root_entry[5] = 13cf13001 > (XEN) context = ffff83013cf13000 > (XEN) context[40] = 0_0 > (XEN) ctxt_entry[40] not present > (XEN) [VT-D]iommu.c:821: iommu_fault_status: Primary Pending Fault > (XEN) [VT-D]iommu.c:796: DMAR:[DMA Write] Request device [05:08.0] fault > addr 2ced30000, iommu reg = ffff82c3fff57000 > (XEN) DMAR:[fault reason 02h] Present bit in context entry is clear > (XEN) print_vtd_entries: iommu = ffff83013ff7b130 bdf = 5:8.0 gmfn > 2ced30 > (XEN) root_entry = ffff83013ff37000 > (XEN) root_entry[5] = 13cf13001 > (XEN) context = ffff83013cf13000 > (XEN) context[40] = 0_0 > (XEN) ctxt_entry[40] not present > calling wait_scan_init+0x0/0x12 [scsi_wait_scan] @ 1132 > initcall wait_scan_init+0x0/0x12 [scsi_wait_scan] returned 0 after 3 > usecs > (XEN) [VT-D]iommu.c:821: iommu_fault_status: Primary Pending Fault > (XEN) [VT-D]iommu.c:796: DMAR:[DMA Write] Request device [05:08.0] fault > addr 2cf14b000, iommu reg = ffff82c3fff57000 > (XEN) DMAR:[fault reason 02h] Present bit in context entry is clear > (XEN) print_vtd_entries: iommu = ffff83013ff7b130 bdf = 5:8.0 gmfn > 2cf14b > (XEN) root_entry = ffff83013ff37000 > (XEN) root_entry[5] = 13cf13001 > (XEN) context = ffff83013cf13000 > (XEN) context[40] = 0_0 > (XEN) ctxt_entry[40] not present > > > On Sat, 2010-05-29 at 18:20 +0300, Pasi Kärkkäinen wrote: > > On Sat, May 29, 2010 at 07:31:17AM -0700, M. Nunberg wrote: > > > I''ve been trying to get VT-D working wiht xen for quite some time, since > > > 3.4.2, and I''ve always had issues with my RAID controller not working > > > properly when iommu is not disabled in Xen: > > > > > > lspci outpuut for the card: > > > > <snip> > > > > > > > > I am using a Supermicro X8DALi motherboard with a 5500 chipset. > > > > > > Whenever I try to access the device the Xen console spits out something > > > like this: > > > (XEN) [VT-D]iommu.c:796: DMAR:[DMA Write] Request device [05:08.0] fault > > > addr 204865000, iommu reg = ffff82c3fff57000 > > > (XEN) DMAR:[fault reason 02h] Present bit in context entry is clear > > > (XEN) print_vtd_entries: iommu = ffff83013fffaee0 bdf = 5:8.0 gmfn > > > 204865 > > > (XEN) root_entry = ffff83013ff37000 > > > (XEN) root_entry[5] = 13cf12001 > > > (XEN) context = ffff83013cf12000 > > > (XEN) context[40] = 0_0 > > > (XEN) ctxt_entry[40] not present > > > (XEN) [VT-D]iommu.c:821: iommu_fault_status: Primary Pending Fault > > > > > > reads are partially succcessful, but I am getting seek errors at times, > > > filesystems will mount properly but I cannot use any of them properly.. > > > > > > > > > The actual kernel output varies, sometimes i get EINVAL when I try to > > > read from the filesystem, sometimes it simply refuses to at all > > > recognize the disk altogether, and other times it will hang the entire > > > system, including the hypervisor itself. > > > I''ve tried booting the hypervisor with x2apic disabled, but to no > > > effect. I''ve also tried with the latest xen-4.0-testing (4.0.1), buut > > > same issue and same outpuut > > > > > > A quick google turns up a thread, from this mailing list, with a > > > different RAID card, but the kernel output is similar.. e.g. > > > > > > scsi scan: INQUIRY result too short (5), using 36 > > > > > > http://lists.xensource.com/archives/html/xen-users/2010-04/msg00535.html > > > > > > The full xen log is below > > > > > > > Did you use the latest pvops dom0 kernel from xen/stable-2.6.32.x branch? > > Could you also post the full serial log _with_ the dom0 kernel messages? > > > > .. since the problem gets triggered by the dom0 kernel.. > > > > -- Pasi > > > > > > > > > > > > > L __ __ _ _ ___ > > > ___ > > > \ \/ /___ _ __ | || | / _ \ / _ \ 0x146000>, shtab=0x3a2078, > > > entry=0x100000 > > > \ // _ \ ''_ \ | || |_| | | | | | > > > | > > > / \ __/ | | | |__ _| |_| | |_| |apper/OS-root ro nomodeset > > > console=tty0 r > > > /_/\_\___|_| |_| | > > > _|(_)___(_)___/ > > > 020 > > > bytes] > > > (XEN) Xen version 4.0.0 (mordy@) (gcc version 4.3.2 (Debian 4.3.2-1.1) ) > > > Fri May 21 07:50:16 PDT 2010boot-module > > > @ > > > (XEN) Latest ChangeSet: > > > unavailable > > > (XEN) Console output is > > > synchronous. > > > (XEN) Command line: iommu=verbose loglvl=all guest_loglvl=all > > > sync_console console_to_rint com1=115200,8n1 > > > console=com1 > > > (XEN) Video > > > information: > > > (XEN) VGA is text mode 80x25, font > > > 8x16 > > > (XEN) VBE/DDC methods: none; EDID transfer time: 0 > > > seconds > > > (XEN) EDID info not retrieved because no DDC retrieval method > > > detected > > > (XEN) Disc information: > > > (XEN) Found 1 MBR signatures > > > (XEN) Found 1 EDD information structures > > > (XEN) Xen-e820 RAM map: > > > (XEN) 0000000000000000 - 000000000009a000 (usable) > > > (XEN) 000000000009a000 - 00000000000a0000 (reserved) > > > (XEN) 00000000000e0000 - 0000000000100000 (reserved) > > > (XEN) 0000000000100000 - 00000000bf760000 (usable) > > > (XEN) 00000000bf76e000 - 00000000bf770000 type 9 > > > (XEN) 00000000bf770000 - 00000000bf77e000 (ACPI data) > > > (XEN) 00000000bf77e000 - 00000000bf7d0000 (ACPI NVS) > > > (XEN) 00000000bf7d0000 - 00000000bf7e0000 (reserved) > > > (XEN) 00000000bf7ec000 - 00000000c0000000 (reserved) > > > (XEN) 00000000fee00000 - 00000000fee01000 (reserved) > > > (XEN) 00000000ffc00000 - 0000000100000000 (reserved) > > > (XEN) 0000000100000000 - 0000000340000000 (usable) > > > (XEN) ACPI: RSDP 000F9E10, 0024 (r2 ACPIAM) > > > (XEN) ACPI: XSDT BF770100, 0094 (r1 NEC 20090424 MSFT > > > 97) > > > (XEN) ACPI: FACP BF770290, 00F4 (r4 042409 FACP1917 20090424 MSFT > > > 97) > > > (XEN) ACPI: DSDT BF770670, 5BFB (r2 10601 10601000 0 INTL > > > 20051117) > > > (XEN) ACPI: FACS BF77E000, 0040 > > > (XEN) ACPI: APIC BF770390, 00D2 (r2 042409 APIC1917 20090424 MSFT > > > 97) > > > (XEN) ACPI: MCFG BF770470, 003C (r1 042409 OEMMCFG 20090424 MSFT > > > 97) > > > (XEN) ACPI: SLIC BF7704B0, 0176 (r1 NEC 20090424 MSFT > > > 97) > > > (XEN) ACPI: ERST BF770630, 0040 (r1 042409 WHEA1917 20090424 MSFT > > > 97) > > > (XEN) ACPI: OEMB BF77E040, 007B (r1 042409 OEMB1917 20090424 MSFT > > > 97) > > > (XEN) ACPI: SRAT BF77A670, 01D0 (r1 042409 OEMSRAT 1 INTL > > > 1) > > > (XEN) ACPI: HPET BF77A840, 0038 (r1 042409 OEMHPET 20090424 MSFT > > > 97) > > > (XEN) ACPI: DMAR BF77E0C0, 0118 (r1 AMI OEMDMAR 1 MSFT > > > 97) > > > (XEN) ACPI: SSDT BF781DF0, 0363 (r1 DpgPmm CpuPm 12 INTL > > > 20051117) > > > (XEN) ACPI: EINJ BF77A880, 0130 (r1 AMIER AMI_EINJ 20090424 MSFT > > > 97) > > > (XEN) ACPI: BERT BF77AA10, 0030 (r1 AMIER AMI_BERT 20090424 MSFT > > > 97) > > > (XEN) ACPI: ERST BF77AA40, 01B0 (r1 AMIER AMI_ERST 20090424 MSFT > > > 97) > > > (XEN) ACPI: HEST BF77ABF0, 00A8 (r1 AMIER AMI_HEST 20090424 MSFT > > > 97) > > > (XEN) System RAM: 12045MB (12334808kB) > > > (XEN) SRAT: PXM 0 -> APIC 0 -> Node 0 > > > (XEN) SRAT: PXM 0 -> APIC 2 -> Node 0 > > > (XEN) SRAT: PXM 0 -> APIC 4 -> Node 0 > > > (XEN) SRAT: PXM 0 -> APIC 6 -> Node 0 > > > (XEN) SRAT: PXM 0 -> APIC 1 -> Node 0 > > > (XEN) SRAT: PXM 0 -> APIC 3 -> Node 0 > > > (XEN) SRAT: PXM 0 -> APIC 5 -> Node 0 > > > (XEN) SRAT: PXM 0 -> APIC 7 -> Node 0 > > > (XEN) SRAT: PXM 1 -> APIC 16 -> Node 1 > > > (XEN) SRAT: PXM 1 -> APIC 18 -> Node 1 > > > (XEN) SRAT: PXM 1 -> APIC 20 -> Node 1 > > > (XEN) SRAT: PXM 1 -> APIC 22 -> Node 1 > > > (XEN) SRAT: PXM 1 -> APIC 17 -> Node 1 > > > (XEN) SRAT: PXM 1 -> APIC 19 -> Node 1 > > > (XEN) SRAT: PXM 1 -> APIC 21 -> Node 1 > > > (XEN) SRAT: PXM 1 -> APIC 23 -> Node 1 > > > (XEN) SRAT: Node 0 PXM 0 0-a0000 > > > (XEN) SRAT: Node 0 PXM 0 100000-c0000000 > > > (XEN) SRAT: Node 0 PXM 0 100000000-1c0000000 > > > (XEN) SRAT: Node 1 PXM 1 1c0000000-340000000 > > > (XEN) NUMA: Allocated memnodemap from 33fdfb000 - 33fdff000 > > > (XEN) NUMA: Using 8 for the hash shift. > > > (XEN) Domain heap initialised DMA width 30 bits > > > (XEN) found SMP MP-table at 000ff780 > > > (XEN) DMI present. > > > (XEN) Using APIC driver default > > > (XEN) ACPI: PM-Timer IO Port: 0x808 > > > (XEN) ACPI: ACPI SLEEP INFO: pm1x_cnt[804,0], pm1x_evt[800,0] > > > (XEN) ACPI: wakeup_vec[bf77e00c], vec_size[20] > > > (XEN) ACPI: Local APIC address 0xfee00000 > > > (XEN) ACPI: LAPIC (acpi_id[0x01] lapic_id[0x00] enabled) > > > (XEN) Processor #0 7:10 APIC version 21 > > > (XEN) ACPI: LAPIC (acpi_id[0x02] lapic_id[0x10] enabled) > > > (XEN) Processor #16 7:10 APIC version 21 > > > (XEN) ACPI: LAPIC (acpi_id[0x03] lapic_id[0x02] enabled) > > > (XEN) Processor #2 7:10 APIC version 21 > > > (XEN) ACPI: LAPIC (acpi_id[0x04] lapic_id[0x12] enabled) > > > (XEN) Processor #18 7:10 APIC version 21 > > > (XEN) ACPI: LAPIC (acpi_id[0x05] lapic_id[0x04] enabled) > > > (XEN) Processor #4 7:10 APIC version 21 > > > (XEN) ACPI: LAPIC (acpi_id[0x06] lapic_id[0x14] enabled) > > > (XEN) Processor #20 7:10 APIC version 21 > > > (XEN) ACPI: LAPIC (acpi_id[0x07] lapic_id[0x06] enabled) > > > (XEN) Processor #6 7:10 APIC version 21 > > > (XEN) ACPI: LAPIC (acpi_id[0x08] lapic_id[0x16] enabled) > > > (XEN) Processor #22 7:10 APIC version 21 > > > (XEN) ACPI: LAPIC (acpi_id[0x09] lapic_id[0x01] enabled) > > > (XEN) Processor #1 7:10 APIC version 21 > > > (XEN) ACPI: LAPIC (acpi_id[0x0a] lapic_id[0x11] enabled) > > > (XEN) Processor #17 7:10 APIC version 21 > > > (XEN) ACPI: LAPIC (acpi_id[0x0b] lapic_id[0x03] enabled) > > > (XEN) Processor #3 7:10 APIC version 21 > > > (XEN) ACPI: LAPIC (acpi_id[0x0c] lapic_id[0x13] enabled) > > > (XEN) Processor #19 7:10 APIC version 21 > > > (XEN) ACPI: LAPIC (acpi_id[0x0d] lapic_id[0x05] enabled) > > > (XEN) Processor #5 7:10 APIC version 21 > > > (XEN) ACPI: LAPIC (acpi_id[0x0e] lapic_id[0x15] enabled) > > > (XEN) Processor #21 7:10 APIC version 21 > > > (XEN) ACPI: LAPIC (acpi_id[0x0f] lapic_id[0x07] enabled) > > > (XEN) Processor #7 7:10 APIC version 21 > > > (XEN) ACPI: LAPIC (acpi_id[0x10] lapic_id[0x17] enabled) > > > (XEN) Processor #23 7:10 APIC version 21 > > > (XEN) ACPI: LAPIC_NMI (acpi_id[0xff] dfl dfl lint[0x1]) > > > (XEN) Overriding APIC driver with bigsmp > > > (XEN) ACPI: IOAPIC (id[0x08] address[0xfec00000] gsi_base[0]) > > > (XEN) IOAPIC[0]: apic_id 8, version 32, address 0xfec00000, GSI 0-23 > > > (XEN) ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl) > > > (XEN) ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 20 low level) > > > (XEN) ACPI: IRQ0 used by override. > > > (XEN) ACPI: IRQ2 used by override. > > > (XEN) ACPI: IRQ9 used by override. > > > (XEN) Enabling APIC mode: Phys. Using 1 I/O APICs > > > (XEN) ACPI: HPET id: 0xffffffff base: 0xfed00000 > > > (XEN) [VT-D]dmar.c:679: Host address width 40 > > > (XEN) [VT-D]dmar.c:694: found ACPI_DMAR_DRHD: > > > (XEN) [VT-D]dmar.c:398: dmaru->address = fbffe000 > > > (XEN) [VT-D]dmar.c:340: IOAPIC: f0:1f.7 > > > (XEN) [VT-D]dmar.c:411: flags: INCLUDE_ALL > > > (XEN) [VT-D]dmar.c:699: found ACPI_DMAR_RMRR: > > > (XEN) [VT-D]dmar.c:334: endpoint: 0:1d.0 > > > (XEN) [VT-D]dmar.c:334: endpoint: 0:1d.1 > > > (XEN) [VT-D]dmar.c:334: endpoint: 0:1d.2 > > > (XEN) [VT-D]dmar.c:334: endpoint: 0:1d.7 > > > (XEN) [VT-D]dmar.c:334: endpoint: 0:1a.0 > > > (XEN) [VT-D]dmar.c:334: endpoint: 0:1a.1 > > > (XEN) [VT-D]dmar.c:334: endpoint: 0:1a.2 > > > (XEN) [VT-D]dmar.c:334: endpoint: 0:1a.7 > > > (XEN) [VT-D]dmar.c:571: RMRR region: base_addr ec000 end_address effff > > > (XEN) [VT-D]dmar.c:699: found ACPI_DMAR_RMRR: > > > (XEN) [VT-D]dmar.c:334: endpoint: 0:1d.0 > > > (XEN) [VT-D]dmar.c:334: endpoint: 0:1d.1 > > > (XEN) [VT-D]dmar.c:334: endpoint: 0:1d.2 > > > (XEN) [VT-D]dmar.c:334: endpoint: 0:1d.7 > > > (XEN) [VT-D]dmar.c:334: endpoint: 0:1a.0 > > > (XEN) [VT-D]dmar.c:334: endpoint: 0:1a.1 > > > (XEN) [VT-D]dmar.c:334: endpoint: 0:1a.2 > > > (XEN) [VT-D]dmar.c:334: endpoint: 0:1a.7 > > > (XEN) [VT-D]dmar.c:571: RMRR region: base_addr bf7ec000 end_address > > > bf7fffff > > > (XEN) [VT-D]dmar.c:704: found ACPI_DMAR_ATSR: > > > (XEN) [VT-D]dmar.c:599: atsru->all_ports: 0 > > > (XEN) [VT-D]dmar.c:320: bridge: 0:1.0 start = 0 sec = 1 sub = 1 > > > (XEN) [VT-D]dmar.c:320: bridge: 0:3.0 start = 0 sec = 2 sub = 2 > > > (XEN) [VT-D]dmar.c:320: bridge: 0:7.0 start = 0 sec = 3 sub = 3 > > > (XEN) PCI: MCFG configuration 0: base e0000000 segment 0 buses 0 - 255 > > > (XEN) PCI: Not using MMCONFIG. > > > (XEN) Using ACPI (MADT) for SMP configuration information > > > (XEN) Using scheduler: SMP Credit Scheduler (credit) > > > (XEN) Detected 2266.790 MHz processor. > > > (XEN) Initing memory sharing. > > > (XEN) VMX: Supported advanced features: > > > (XEN) - APIC MMIO access virtualisation > > > (XEN) - APIC TPR shadow > > > (XEN) - Extended Page Tables (EPT) > > > (XEN) - Virtual-Processor Identifiers (VPID) > > > (XEN) - Virtual NMI > > > (XEN) - MSR direct-access bitmap > > > (XEN) HVM: ASIDs enabled. > > > (XEN) HVM: VMX enabled > > > (XEN) HVM: Hardware Assisted Paging detected. > > > (XEN) Intel machine check reporting enabled > > > (XEN) [VT-D]iommu.c:1078: drhd->address = fbffe000 iommu->reg > > > ffff82c3fff57000 > > > (XEN) [VT-D]iommu.c:1080: cap = c90780106f0462 ecap = f0207e > > > (XEN) Intel VT-d Snoop Control not supported. > > > (XEN) Intel VT-d DMA Passthrough not supported. > > > (XEN) Intel VT-d Queued Invalidation supported. > > > (XEN) Intel VT-d Interrupt Remapping supported. > > > (XEN) I/O virtualisation enabled > > > (XEN) I/O virtualisation for PV guests disabled > > > (XEN) Total of 16 processors activated. > > > (XEN) ENABLING IO-APIC IRQs > > > (XEN) -> Using new ACK method > > > (XEN) ..TIMER: vector=0xF0 apic1=0 pin1=2 apic2=-1 pin2=-1 > > > (XEN) TSC is reliable, synchronization unnecessary > > > (XEN) Platform timer is 14.318MHz HPET > > > ?(XEN) Allocated console ring of 128 KiB. > > > (XEN) microcode.c:73:d32767 microcode: CPU1 resumed > > > (XEN) microcode.c:73:d32767 microcode: CPU9 resumed > > > (XEN) microcode.c:73:d32767 microcode: CPU14 resumed > > > (XEN) microcode.c:73:d32767 microcode: CPU6 resumed > > > (XEN) microcode.c:73:d32767 microcode: CPU3 resumed > > > (XEN) microcode.c:73:d32767 microcode: CPU11 resumed > > > (XEN) microcode.c:73:d32767 microcode: CPU8 resumed > > > (XEN) microcode.c:73:d32767 microcode: CPU7 resumed > > > (XEN) microcode.c:73:d32767 microcode: CPU15 resumed > > > (XEN) microcode.c:73:d32767 microcode: CPU2 resumed > > > (XEN) microcode.c:73:d32767 microcode: CPU5 resumed > > > (XEN) microcode.c:73:d32767 microcode: CPU13 resumed > > > (XEN) microcode.c:73:d32767 microcode: CPU4 resumed > > > (XEN) microcode.c:73:d32767 microcode: CPU10 resumed > > > (XEN) Brought up 16 CPUs > > > (XEN) microcode.c:73:d32767 microcode: CPU12 resumed > > > (XEN) Turbo Mode detected! > > > (XEN) HPET''s MSI mode hasn''t been supported when Interrupt Remapping is > > > enabled. > > > (XEN) ACPI sleep modes: S3 > > > (XEN) mcheck_poll: Machine check polling timer started. > > > (XEN) [VT-D]iommu.c:1325: d0:PCIe: map bdf = 0:0.0 > > > (XEN) [VT-D]iommu.c:1325: d0:PCIe: map bdf = 0:14.0 > > > (XEN) [VT-D]iommu.c:1325: d0:PCIe: map bdf = 0:14.1 > > > (XEN) [VT-D]iommu.c:1325: d0:PCIe: map bdf = 0:14.2 > > > (XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = 0:14.3 > > > (XEN) [VT-D]iommu.c:1325: d0:PCIe: map bdf = 0:16.0 > > > (XEN) [VT-D]iommu.c:1325: d0:PCIe: map bdf = 0:16.1 > > > (XEN) [VT-D]iommu.c:1325: d0:PCIe: map bdf = 0:16.2 > > > (XEN) [VT-D]iommu.c:1325: d0:PCIe: map bdf = 0:16.3 > > > (XEN) [VT-D]iommu.c:1325: d0:PCIe: map bdf = 0:16.4 > > > (XEN) [VT-D]iommu.c:1325: d0:PCIe: map bdf = 0:16.5 > > > (XEN) [VT-D]iommu.c:1325: d0:PCIe: map bdf = 0:16.6 > > > (XEN) [VT-D]iommu.c:1325: d0:PCIe: map bdf = 0:16.7 > > > (XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = 0:1a.0 > > > (XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = 0:1a.1 > > > (XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = 0:1a.2 > > > (XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = 0:1a.7 > > > (XEN) [VT-D]iommu.c:1325: d0:PCIe: map bdf = 0:1b.0 > > > (XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = 0:1d.0 > > > (XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = 0:1d.1 > > > (XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = 0:1d.2 > > > (XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = 0:1d.7 > > > (XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = 0:1f.0 > > > (XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = 0:1f.2 > > > (XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = 0:1f.3 > > > (XEN) [VT-D]iommu.c:1325: d0:PCIe: map bdf = 1:0.0 > > > (XEN) [VT-D]iommu.c:1325: d0:PCIe: map bdf = 3:0.0 > > > (XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = 5:e.0 > > > (XEN) [VT-D]iommu.c:1325: d0:PCIe: map bdf = 7:0.0 > > > (XEN) [VT-D]iommu.c:1325: d0:PCIe: map bdf = 8:0.0 > > > (XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = fe:0.0 > > > (XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = fe:0.1 > > > (XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = fe:2.0 > > > (XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = fe:2.1 > > > (XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = fe:2.4 > > > (XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = fe:2.5 > > > (XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = fe:3.0 > > > (XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = fe:3.1 > > > (XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = fe:3.2 > > > (XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = fe:3.4 > > > (XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = fe:4.0 > > > (XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = fe:4.1 > > > (XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = fe:4.2 > > > (XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = fe:4.3 > > > (XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = fe:5.0 > > > (XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = fe:5.1 > > > (XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = fe:5.2 > > > (XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = fe:5.3 > > > (XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = fe:6.0 > > > (XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = fe:6.1 > > > (XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = fe:6.2 > > > (XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = fe:6.3 > > > (XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = ff:0.0 > > > (XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = ff:0.1 > > > (XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = ff:2.0 > > > (XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = ff:2.1 > > > (XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = ff:2.4 > > > (XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = ff:2.5 > > > (XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = ff:3.0 > > > (XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = ff:3.1 > > > (XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = ff:3.2 > > > (XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = ff:3.4 > > > (XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = ff:4.0 > > > (XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = ff:4.1 > > > (XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = ff:4.2 > > > (XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = ff:4.3 > > > (XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = ff:5.0 > > > (XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = ff:5.1 > > > (XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = ff:5.2 > > > (XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = ff:5.3 > > > (XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = ff:6.0 > > > (XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = ff:6.1 > > > (XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = ff:6.2 > > > (XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = ff:6.3 > > > (XEN) [VT-D]iommu.c:695: iommu_enable_translation: iommu->reg > > > ffff82c3fff57000 > > > (XEN) *** LOADING DOMAIN 0 *** > > > (XEN) Xen kernel: 64-bit, lsb, compat32 > > > (XEN) Dom0 kernel: 64-bit, PAE, lsb, paddr 0x1000000 -> 0x26b6000 > > > (XEN) PHYSICAL MEMORY ARRANGEMENT: > > > (XEN) Dom0 alloc.: 0000000100000000->0000000120000000 (2937045 pages > > > to be allocated) > > > (XEN) VIRTUAL MEMORY ARRANGEMENT: > > > (XEN) Loaded kernel: ffffffff81000000->ffffffff826b6000 > > > (XEN) Init. ramdisk: ffffffff826b6000->ffffffff8f7d7600 > > > (XEN) Phys-Mach map: ffffffff8f7d8000->ffffffff90f406a8 > > > (XEN) Start info: ffffffff90f41000->ffffffff90f414b4 > > > (XEN) Page tables: ffffffff90f42000->ffffffff90fcf000 > > > (XEN) Boot stack: ffffffff90fcf000->ffffffff90fd0000 > > > (XEN) TOTAL: ffffffff80000000->ffffffff91400000 > > > (XEN) ENTRY ADDRESS: ffffffff819be200 > > > (XEN) Dom0 has maximum 16 VCPUs > > > (XEN) Scrubbing Free RAM: .done. > > > (XEN) Xen trace buffers: disabled > > > (XEN) Std. Loglevel: All > > > (XEN) Guest Loglevel: All > > > (XEN) ********************************************** > > > (XEN) ******* WARNING: CONSOLE OUTPUT IS SYNCHRONOUS > > > (XEN) ******* This option is intended to aid debugging of Xen by > > > ensuring > > > (XEN) ******* that all output is synchronously delivered on the serial > > > line. > > > (XEN) ******* However it can introduce SIGNIFICANT latencies and affect > > > (XEN) ******* timekeeping. It is NOT recommended for production use! > > > (XEN) ********************************************** > > > (XEN) 3... 2... 1... > > > (XEN) *** Serial input -> DOM0 (type ''CTRL-a'' three times to switch > > > input to Xen) > > > (XEN) Freed 164kB init memory. > > > mapping kernel into physical memory > > > Xen: setup ISA identity maps > > > about to get started... > > > (XEN) PCI add device 00:00.0 > > > (XEN) PCI add device 00:01.0 > > > (XEN) PCI add device 00:03.0 > > > (XEN) PCI add device 00:07.0 > > > (XEN) PCI add device 00:14.0 > > > (XEN) PCI add device 00:14.1 > > > (XEN) PCI add device 00:14.2 > > > (XEN) PCI add device 00:14.3 > > > (XEN) PCI add device 00:16.0 > > > (XEN) PCI add device 00:16.1 > > > (XEN) PCI add device 00:16.2 > > > (XEN) PCI add device 00:16.3 > > > (XEN) PCI add device 00:16.4 > > > (XEN) PCI add device 00:16.5 > > > (XEN) PCI add device 00:16.6 > > > (XEN) PCI add device 00:16.7 > > > (XEN) PCI add device 00:1a.0 > > > (XEN) PCI add device 00:1a.1 > > > (XEN) PCI add device 00:1a.2 > > > (XEN) PCI add device 00:1a.7 > > > (XEN) PCI add device 00:1b.0 > > > (XEN) PCI add device 00:1c.0 > > > (XEN) PCI add device 00:1c.4 > > > (XEN) PCI add device 00:1c.5 > > > (XEN) PCI add device 00:1d.0 > > > (XEN) PCI add device 00:1d.1 > > > (XEN) PCI add device 00:1d.2 > > > (XEN) PCI add device 00:1d.7 > > > (XEN) PCI add device 00:1e.0 > > > (XEN) PCI add device 00:1f.0 > > > (XEN) PCI add device 00:1f.2 > > > (XEN) PCI add device 00:1f.3 > > > (XEN) PCI add device 01:00.0 > > > (XEN) PCI add device 03:00.0 > > > (XEN) PCI add device 04:00.0 > > > (XEN) PCI add device 04:00.2 > > > (XEN) PCI add device 05:0e.0 > > > (XEN) PCI add device 07:00.0 > > > (XEN) PCI add device 08:00.0 > > > (XEN) cpuid.MWAIT[.eax=40, .ebx=40, .ecx=3, .edx=1120] > > > (XEN) Monitor-Mwait will be used to enter C-1 state > > > (XEN) cpuid.MWAIT[.eax=40, .ebx=40, .ecx=3, .edx=1120] > > > (XEN) Monitor-Mwait will be used to enter C-3 state > > > (XEN) cpuid.MWAIT[.eax=40, .ebx=40, .ecx=3, .edx=1120] > > > (XEN) Monitor-Mwait will be used to enter C-3 state > > > (XEN) cpuid.MWAIT[.eax=40, .ebx=40, .ecx=3, .edx=1120] > > > (XEN) Monitor-Mwait will be used to enter C-1 state > > > (XEN) cpuid.MWAIT[.eax=40, .ebx=40, .ecx=3, .edx=1120] > > > (XEN) Monitor-Mwait will be used to enter C-3 state > > > (XEN) cpuid.MWAIT[.eax=40, .ebx=40, .ecx=3, .edx=1120] > > > (XEN) Monitor-Mwait will be used to enter C-3 state > > > (XEN) cpuid.MWAIT[.eax=40, .ebx=40, .ecx=3, .edx=1120] > > > (XEN) Monitor-Mwait will be used to enter C-1 state > > > (XEN) cpuid.MWAIT[.eax=40, .ebx=40, .ecx=3, .edx=1120] > > > (XEN) Monitor-Mwait will be used to enter C-3 state > > > (XEN) cpuid.MWAIT[.eax=40, .ebx=40, .ecx=3, .edx=1120] > > > (XEN) Monitor-Mwait will be used to enter C-3 state > > > (XEN) cpuid.MWAIT[.eax=40, .ebx=40, .ecx=3, .edx=1120] > > > (XEN) Monitor-Mwait will be used to enter C-1 state > > > (XEN) cpuid.MWAIT[.eax=40, .ebx=40, .ecx=3, .edx=1120] > > > (XEN) Monitor-Mwait will be used to enter C-3 state > > > (XEN) cpuid.MWAIT[.eax=40, .ebx=40, .ecx=3, .edx=1120] > > > (XEN) Monitor-Mwait will be used to enter C-3 state > > > (XEN) cpuid.MWAIT[.eax=40, .ebx=40, .ecx=3, .edx=1120] > > > (XEN) Monitor-Mwait will be used to enter C-1 state > > > (XEN) cpuid.MWAIT[.eax=40, .ebx=40, .ecx=3, .edx=1120] > > > (XEN) Monitor-Mwait will be used to enter C-3 state > > > (XEN) cpuid.MWAIT[.eax=40, .ebx=40, .ecx=3, .edx=1120] > > > (XEN) Monitor-Mwait will be used to enter C-3 state > > > (XEN) cpuid.MWAIT[.eax=40, .ebx=40, .ecx=3, .edx=1120] > > > (XEN) Monitor-Mwait will be used to enter C-1 state > > > (XEN) cpuid.MWAIT[.eax=40, .ebx=40, .ecx=3, .edx=1120] > > > (XEN) Monitor-Mwait will be used to enter C-3 state > > > (XEN) cpuid.MWAIT[.eax=40, .ebx=40, .ecx=3, .edx=1120] > > > (XEN) Monitor-Mwait will be used to enter C-3 state > > > (XEN) cpuid.MWAIT[.eax=40, .ebx=40, .ecx=3, .edx=1120] > > > (XEN) Monitor-Mwait will be used to enter C-1 state > > > (XEN) cpuid.MWAIT[.eax=40, .ebx=40, .ecx=3, .edx=1120] > > > (XEN) Monitor-Mwait will be used to enter C-3 state > > > (XEN) cpuid.MWAIT[.eax=40, .ebx=40, .ecx=3, .edx=1120] > > > (XEN) Monitor-Mwait will be used to enter C-3 state > > > (XEN) cpuid.MWAIT[.eax=40, .ebx=40, .ecx=3, .edx=1120] > > > (XEN) Monitor-Mwait will be used to enter C-1 state > > > (XEN) cpuid.MWAIT[.eax=40, .ebx=40, .ecx=3, .edx=1120] > > > (XEN) Monitor-Mwait will be used to enter C-3 state > > > (XEN) cpuid.MWAIT[.eax=40, .ebx=40, .ecx=3, .edx=1120] > > > (XEN) Monitor-Mwait will be used to enter C-3 state > > > (XEN) cpuid.MWAIT[.eax=40, .ebx=40, .ecx=3, .edx=1120] > > > (XEN) Monitor-Mwait will be used to enter C-1 state > > > (XEN) cpuid.MWAIT[.eax=40, .ebx=40, .ecx=3, .edx=1120] > > > (XEN) Monitor-Mwait will be used to enter C-3 state > > > (XEN) cpuid.MWAIT[.eax=40, .ebx=40, .ecx=3, .edx=1120] > > > (XEN) Monitor-Mwait will be used to enter C-3 state > > > (XEN) cpuid.MWAIT[.eax=40, .ebx=40, .ecx=3, .edx=1120] > > > (XEN) Monitor-Mwait will be used to enter C-1 state > > > (XEN) cpuid.MWAIT[.eax=40, .ebx=40, .ecx=3, .edx=1120] > > > (XEN) Monitor-Mwait will be used to enter C-3 state > > > (XEN) cpuid.MWAIT[.eax=40, .ebx=40, .ecx=3, .edx=1120] > > > (XEN) Monitor-Mwait will be used to enter C-3 state > > > (XEN) cpuid.MWAIT[.eax=40, .ebx=40, .ecx=3, .edx=1120] > > > (XEN) Monitor-Mwait will be used to enter C-1 state > > > (XEN) cpuid.MWAIT[.eax=40, .ebx=40, .ecx=3, .edx=1120] > > > (XEN) Monitor-Mwait will be used to enter C-3 state > > > (XEN) cpuid.MWAIT[.eax=40, .ebx=40, .ecx=3, .edx=1120] > > > (XEN) Monitor-Mwait will be used to enter C-3 state > > > (XEN) cpuid.MWAIT[.eax=40, .ebx=40, .ecx=3, .edx=1120] > > > (XEN) Monitor-Mwait will be used to enter C-1 state > > > (XEN) cpuid.MWAIT[.eax=40, .ebx=40, .ecx=3, .edx=1120] > > > (XEN) Monitor-Mwait will be used to enter C-3 state > > > (XEN) cpuid.MWAIT[.eax=40, .ebx=40, .ecx=3, .edx=1120] > > > (XEN) Monitor-Mwait will be used to enter C-3 state > > > (XEN) cpuid.MWAIT[.eax=40, .ebx=40, .ecx=3, .edx=1120] > > > (XEN) Monitor-Mwait will be used to enter C-1 state > > > (XEN) cpuid.MWAIT[.eax=40, .ebx=40, .ecx=3, .edx=1120] > > > (XEN) Monitor-Mwait will be used to enter C-3 state > > > (XEN) cpuid.MWAIT[.eax=40, .ebx=40, .ecx=3, .edx=1120] > > > (XEN) Monitor-Mwait will be used to enter C-3 state > > > (XEN) cpuid.MWAIT[.eax=40, .ebx=40, .ecx=3, .edx=1120] > > > (XEN) Monitor-Mwait will be used to enter C-1 state > > > (XEN) cpuid.MWAIT[.eax=40, .ebx=40, .ecx=3, .edx=1120] > > > (XEN) Monitor-Mwait will be used to enter C-3 state > > > (XEN) cpuid.MWAIT[.eax=40, .ebx=40, .ecx=3, .edx=1120] > > > (XEN) Monitor-Mwait will be used to enter C-3 state > > > (XEN) cpuid.MWAIT[.eax=40, .ebx=40, .ecx=3, .edx=1120] > > > (XEN) Monitor-Mwait will be used to enter C-1 state > > > (XEN) cpuid.MWAIT[.eax=40, .ebx=40, .ecx=3, .edx=1120] > > > (XEN) Monitor-Mwait will be used to enter C-3 state > > > (XEN) cpuid.MWAIT[.eax=40, .ebx=40, .ecx=3, .edx=1120] > > > (XEN) Monitor-Mwait will be used to enter C-3 state > > > (XEN) cpuid.MWAIT[.eax=40, .ebx=40, .ecx=3, .edx=1120] > > > (XEN) Monitor-Mwait will be used to enter C-1 state > > > (XEN) cpuid.MWAIT[.eax=40, .ebx=40, .ecx=3, .edx=1120] > > > (XEN) Monitor-Mwait will be used to enter C-3 state > > > (XEN) cpuid.MWAIT[.eax=40, .ebx=40, .ecx=3, .edx=1120] > > > (XEN) Monitor-Mwait will be used to enter C-3 state > > > (XEN) irq.c:1139:d0 Cannot bind IRQ 4 to guest. In use by ''ns16550''. > > > (XEN) irq.c:1139:d0 Cannot bind IRQ 2 to guest. In use by ''cascade''. > > > (XEN) irq.c:1139:d0 Cannot bind IRQ 4 to guest. In use by ''ns16550''. > > > (XEN) irq.c:1139:d0 Cannot bind IRQ 2 to guest. In use by ''cascade''. > > > (XEN) irq.c:1139:d0 Cannot bind IRQ 4 to guest. In use by ''ns16550''. > > > (XEN) irq.c:1139:d0 Cannot bind IRQ 2 to guest. In use by ''cascade''. > > > (XEN) irq.c:1139:d0 Cannot bind IRQ 4 to guest. In use by ''ns16550''. > > > (XEN) irq.c:1139:d0 Cannot bind IRQ 2 to guest. In use by ''cascade''. > > > (XEN) [VT-D]iommu.c:821: iommu_fault_status: Primary Pending Fault > > > (XEN) [VT-D]iommu.c:796: DMAR:[DMA Write] Request device [05:08.0] fault > > > addr 203a09000, iommu reg = ffff82c3fff57000 > > > (XEN) DMAR:[fault reason 02h] Present bit in context entry is clear > > > (XEN) print_vtd_entries: iommu = ffff83013fffaee0 bdf = 5:8.0 gmfn > > > 203a09 > > > (XEN) root_entry = ffff83013ff37000 > > > (XEN) root_entry[5] = 13cf12001 > > > (XEN) context = ffff83013cf12000 > > > (XEN) context[40] = 0_0 > > > (XEN) ctxt_entry[40] not present > > > (XEN) [VT-D]iommu.c:796: DMAR:[DMA Write] Request device [05:08.0] fault > > > addr 203eba000, iommu reg = ffff82c3fff57000 > > > (XEN) DMAR:[fault reason 02h] Present bit in context entry is clear > > > (XEN) print_vtd_entries: iommu = ffff83013fffaee0 bdf = 5:8.0 gmfn > > > 203eba > > > (XEN) root_entry = ffff83013ff37000 > > > (XEN) root_entry[5] = 13cf12001 > > > (XEN) context = ffff83013cf12000 > > > (XEN) context[40] = 0_0 > > > (XEN) ctxt_entry[40] not present > > > (XEN) [VT-D]iommu.c:821: iommu_fault_status: Primary Pending Fault > > > (XEN) [VT-D]iommu.c:796: DMAR:[DMA Write] Request device [05:08.0] fault > > > addr 204e11000, iommu reg = ffff82c3fff57000 > > > (XEN) DMAR:[fault reason 02h] Present bit in context entry is clear > > > (XEN) print_vtd_entries: iommu = ffff83013fffaee0 bdf = 5:8.0 gmfn > > > 204e11 > > > (XEN) root_entry = ffff83013ff37000 > > > (XEN) root_entry[5] = 13cf12001 > > > (XEN) context = ffff83013cf12000 > > > (XEN) context[40] = 0_0 > > > (XEN) ctxt_entry[40] not present > > > (XEN) [VT-D]iommu.c:821: iommu_fault_status: Primary Pending Fault > > > (XEN) [VT-D]iommu.c:796: DMAR:[DMA Write] Request device [05:08.0] fault > > > addr 2061e2000, iommu reg = ffff82c3fff57000 > > > (XEN) DMAR:[fault reason 02h] Present bit in context entry is clear > > > (XEN) print_vtd_entries: iommu = ffff83013fffaee0 bdf = 5:8.0 gmfn > > > 2061e2 > > > (XEN) root_entry = ffff83013ff37000 > > > (XEN) root_entry[5] = 13cf12001 > > > (XEN) context = ffff83013cf12000 > > > (XEN) context[40] = 0_0 > > > (XEN) ctxt_entry[40] not present > > > (XEN) [VT-D]iommu.c:796: DMAR:[DMA Write] Request device [05:08.0] fault > > > addr 205043000, iommu reg = ffff82c3fff57000 > > > (XEN) DMAR:[fault reason 02h] Present bit in context entry is clear > > > (XEN) print_vtd_entries: iommu = ffff83013fffaee0 bdf = 5:8.0 gmfn > > > 205043 > > > (XEN) root_entry = ffff83013ff37000 > > > (XEN) root_entry[5] = 13cf12001 > > > (XEN) context = ffff83013cf12000 > > > (XEN) context[40] = 0_0 > > > (XEN) ctxt_entry[40] not present > > > (XEN) [VT-D]iommu.c:821: iommu_fault_status: Primary Pending Fault > > > (XEN) [VT-D]iommu.c:796: DMAR:[DMA Write] Request device [05:08.0] fault > > > addr 20552b000, iommu reg = ffff82c3fff57000 > > > (XEN) DMAR:[fault reason 02h] Present bit in context entry is clear > > > (XEN) print_vtd_entries: iommu = ffff83013fffaee0 bdf = 5:8.0 gmfn > > > 20552b > > > (XEN) root_entry = ffff83013ff37000 > > > (XEN) root_entry[5] = 13cf12001 > > > (XEN) context = ffff83013cf12000 > > > (XEN) context[40] = 0_0 > > > (XEN) ctxt_entry[40] not present > > > (XEN) [VT-D]iommu.c:821: iommu_fault_status: Primary Pending Fault > > > (XEN) [VT-D]iommu.c:796: DMAR:[DMA Write] Request device [05:08.0] fault > > > addr 205708000, iommu reg = ffff82c3fff57000 > > > (XEN) DMAR:[fault reason 02h] Present bit in context entry is clear > > > (XEN) print_vtd_entries: iommu = ffff83013fffaee0 bdf = 5:8.0 gmfn > > > 205708 > > > (XEN) root_entry = ffff83013ff37000 > > > (XEN) root_entry[5] = 13cf12001 > > > (XEN) context = ffff83013cf12000 > > > (XEN) context[40] = 0_0 > > > (XEN) ctxt_entry[40] not present > > > (XEN) [VT-D]iommu.c:796: DMAR:[DMA Write] Request device [05:08.0] fault > > > addr 2060c0000, iommu reg = ffff82c3fff57000 > > > (XEN) DMAR:[fault reason 02h] Present bit in context entry is clear > > > (XEN) print_vtd_entries: iommu = ffff83013fffaee0 bdf = 5:8.0 gmfn > > > 2060c0 > > > (XEN) root_entry = ffff83013ff37000 > > > (XEN) root_entry[5] = 13cf12001 > > > (XEN) context = ffff83013cf12000 > > > (XEN) context[40] = 0_0 > > > (XEN) ctxt_entry[40] not present > > > (XEN) [VT-D]iommu.c:821: iommu_fault_status: Primary Pending Fault > > > (XEN) [VT-D]iommu.c:796: DMAR:[DMA Write] Request device [05:08.0] fault > > > addr 206591000, iommu reg = ffff82c3fff57000 > > > (XEN) DMAR:[fault reason 02h] Present bit in context entry is clear > > > (XEN) print_vtd_entries: iommu = ffff83013fffaee0 bdf = 5:8.0 gmfn > > > 206591 > > > (XEN) root_entry = ffff83013ff37000 > > > (XEN) root_entry[5] = 13cf12001 > > > (XEN) context = ffff83013cf12000 > > > (XEN) context[40] = 0_0 > > > (XEN) ctxt_entry[40] not present > > > (XEN) [VT-D]iommu.c:796: DMAR:[DMA Write] Request device [05:08.0] fault > > > addr 204353000, iommu reg = ffff82c3fff57000 > > > (XEN) DMAR:[fault reason 02h] Present bit in context entry is clear > > > (XEN) print_vtd_entries: iommu = ffff83013fffaee0 bdf = 5:8.0 gmfn > > > 204353 > > > (XEN) root_entry = ffff83013ff37000 > > > (XEN) root_entry[5] = 13cf12001 > > > (XEN) context = ffff83013cf12000 > > > (XEN) context[40] = 0_0 > > > (XEN) ctxt_entry[40] not present > > > (XEN) [VT-D]iommu.c:821: iommu_fault_status: Primary Pending Fault > > > (XEN) [VT-D]iommu.c:796: DMAR:[DMA Write] Request device [05:08.0] fault > > > addr 2061f2000, iommu reg = ffff82c3fff57000 > > > (XEN) DMAR:[fault reason 02h] Present bit in context entry is clear > > > (XEN) print_vtd_entries: iommu = ffff83013fffaee0 bdf = 5:8.0 gmfn > > > 2061f2 > > > (XEN) root_entry = ffff83013ff37000 > > > (XEN) root_entry[5] = 13cf12001 > > > (XEN) context = ffff83013cf12000 > > > (XEN) context[40] = 0_0 > > > (XEN) ctxt_entry[40] not present > > > (XEN) [VT-D]iommu.c:796: DMAR:[DMA Write] Request device [05:08.0] fault > > > addr 204306000, iommu reg = ffff82c3fff57000 > > > (XEN) DMAR:[fault reason 02h] Present bit in context entry is clear > > > (XEN) print_vtd_entries: iommu = ffff83013fffaee0 bdf = 5:8.0 gmfn > > > 204306 > > > (XEN) root_entry = ffff83013ff37000 > > > (XEN) root_entry[5] = 13cf12001 > > > (XEN) context = ffff83013cf12000 > > > (XEN) context[40] = 0_0 > > > (XEN) ctxt_entry[40] not present > > > (XEN) [VT-D]iommu.c:821: iommu_fault_status: Primary Pending Fault > > > (XEN) [VT-D]iommu.c:796: DMAR:[DMA Write] Request device [05:08.0] fault > > > addr 205f6b000, iommu reg = ffff82c3fff57000 > > > (XEN) DMAR:[fault reason 02h] Present bit in context entry is clear > > > (XEN) print_vtd_entries: iommu = ffff83013fffaee0 bdf = 5:8.0 gmfn > > > 205f6b > > > (XEN) root_entry = ffff83013ff37000 > > > (XEN) root_entry[5] = 13cf12001 > > > (XEN) context = ffff83013cf12000 > > > (XEN) context[40] = 0_0 > > > (XEN) ctxt_entry[40] not present > > > (XEN) [VT-D]iommu.c:796: DMAR:[DMA Write] Request device [05:08.0] fault > > > addr 205665000, iommu reg = ffff82c3fff57000 > > > (XEN) DMAR:[fault reason 02h] Present bit in context entry is clear > > > (XEN) print_vtd_entries: iommu = ffff83013fffaee0 bdf = 5:8.0 gmfn > > > 205665 > > > (XEN) root_entry = ffff83013ff37000 > > > (XEN) root_entry[5] = 13cf12001 > > > (XEN) context = ffff83013cf12000 > > > (XEN) context[40] = 0_0 > > > (XEN) ctxt_entry[40] not present > > > (XEN) [VT-D]iommu.c:821: iommu_fault_status: Primary Pending Fault > > > (XEN) [VT-D]iommu.c:796: DMAR:[DMA Write] Request device [05:08.0] fault > > > addr 2045a0000, iommu reg = ffff82c3fff57000 > > > (XEN) DMAR:[fault reason 02h] Present bit in context entry is clear > > > (XEN) print_vtd_entries: iommu = ffff83013fffaee0 bdf = 5:8.0 gmfn > > > 2045a0 > > > (XEN) root_entry = ffff83013ff37000 > > > (XEN) root_entry[5] = 13cf12001 > > > (XEN) context = ffff83013cf12000 > > > (XEN) context[40] = 0_0 > > > (XEN) ctxt_entry[40] not present > > > (XEN) [VT-D]iommu.c:796: DMAR:[DMA Write] Request device [05:08.0] fault > > > addr 205669000, iommu reg = ffff82c3fff57000 > > > (XEN) DMAR:[fault reason 02h] Present bit in context entry is clear > > > (XEN) print_vtd_entries: iommu = ffff83013fffaee0 bdf = 5:8.0 gmfn > > > 205669 > > > (XEN) root_entry = ffff83013ff37000 > > > (XEN) root_entry[5] = 13cf12001 > > > (XEN) context = ffff83013cf12000 > > > (XEN) context[40] = 0_0 > > > (XEN) ctxt_entry[40] not present > > > (XEN) [VT-D]iommu.c:821: iommu_fault_status: Primary Pending Fault > > > (XEN) [VT-D]iommu.c:796: DMAR:[DMA Write] Request device [05:08.0] fault > > > addr 2042c6000, iommu reg = ffff82c3fff57000 > > > (XEN) DMAR:[fault reason 02h] Present bit in context entry is clear > > > (XEN) print_vtd_entries: iommu = ffff83013fffaee0 bdf = 5:8.0 gmfn > > > 2042c6 > > > (XEN) root_entry = ffff83013ff37000 > > > (XEN) root_entry[5] = 13cf12001 > > > (XEN) context = ffff83013cf12000 > > > (XEN) context[40] = 0_0 > > > (XEN) ctxt_entry[40] not present > > > (XEN) [VT-D]iommu.c:796: DMAR:[DMA Write] Request device [05:08.0] fault > > > addr 2061fe000, iommu reg = ffff82c3fff57000 > > > (XEN) DMAR:[fault reason 02h] Present bit in context entry is clear > > > (XEN) print_vtd_entries: iommu = ffff83013fffaee0 bdf = 5:8.0 gmfn > > > 2061fe > > > (XEN) root_entry = ffff83013ff37000 > > > (XEN) root_entry[5] = 13cf12001 > > > (XEN) context = ffff83013cf12000 > > > (XEN) context[40] = 0_0 > > > (XEN) ctxt_entry[40] not present > > > (XEN) [VT-D]iommu.c:821: iommu_fault_status: Primary Pending Fault > > > (XEN) [VT-D]iommu.c:796: DMAR:[DMA Write] Request device [05:08.0] fault > > > addr 20560a000, iommu reg = ffff82c3fff57000 > > > (XEN) DMAR:[fault reason 02h] Present bit in context entry is clear > > > (XEN) print_vtd_entries: iommu = ffff83013fffaee0 bdf = 5:8.0 gmfn > > > 20560a > > > (XEN) root_entry = ffff83013ff37000 > > > (XEN) root_entry[5] = 13cf12001 > > > (XEN) context = ffff83013cf12000 > > > (XEN) context[40] = 0_0 > > > (XEN) ctxt_entry[40] not present > > > (XEN) [VT-D]iommu.c:796: DMAR:[DMA Write] Request device [05:08.0] fault > > > addr 206003000, iommu reg = ffff82c3fff57000 > > > (XEN) DMAR:[fault reason 02h] Present bit in context entry is clear > > > (XEN) print_vtd_entries: iommu = ffff83013fffaee0 bdf = 5:8.0 gmfn > > > 206003 > > > (XEN) root_entry = ffff83013ff37000 > > > (XEN) root_entry[5] = 13cf12001 > > > (XEN) context = ffff83013cf12000 > > > (XEN) context[40] = 0_0 > > > (XEN) ctxt_entry[40] not present > > > (XEN) [VT-D]iommu.c:821: iommu_fault_status: Primary Pending Fault > > > (XEN) [VT-D]iommu.c:796: DMAR:[DMA Write] Request device [05:08.0] fault > > > addr 20583e000, iommu reg = ffff82c3fff57000 > > > (XEN) DMAR:[fault reason 02h] Present bit in context entry is clear > > > (XEN) print_vtd_entries: iommu = ffff83013fffaee0 bdf = 5:8.0 gmfn > > > 20583e > > > (XEN) root_entry = ffff83013ff37000 > > > (XEN) root_entry[5] = 13cf12001 > > > (XEN) context = ffff83013cf12000 > > > (XEN) context[40] = 0_0 > > > (XEN) ctxt_entry[40] not present > > > (XEN) [VT-D]iommu.c:796: DMAR:[DMA Write] Request device [05:08.0] fault > > > addr 205615000, iommu reg = ffff82c3fff57000 > > > (XEN) DMAR:[fault reason 02h] Present bit in context entry is clear > > > (XEN) print_vtd_entries: iommu = ffff83013fffaee0 bdf = 5:8.0 gmfn > > > 205615 > > > (XEN) root_entry = ffff83013ff37000 > > > (XEN) root_entry[5] = 13cf12001 > > > (XEN) context = ffff83013cf12000 > > > (XEN) context[40] = 0_0 > > > (XEN) ctxt_entry[40] not present > > > (XEN) [VT-D]iommu.c:796: DMAR:[DMA Write] Request device [05:08.0] fault > > > addr 204265000, iommu reg = ffff82c3fff57000 > > > (XEN) DMAR:[fault reason 02h] Present bit in context entry is clear > > > (XEN) print_vtd_entries: iommu = ffff83013fffaee0 bdf = 5:8.0 gmfn > > > 204265 > > > (XEN) root_entry = ffff83013ff37000 > > > (XEN) root_entry[5] = 13cf12001 > > > (XEN) context = ffff83013cf12000 > > > (XEN) context[40] = 0_0 > > > (XEN) ctxt_entry[40] not present > > > (XEN) [VT-D]iommu.c:821: iommu_fault_status: Primary Pending Fault > > > (XEN) [VT-D]iommu.c:796: DMAR:[DMA Write] Request device [05:08.0] fault > > > addr 207498000, iommu reg = ffff82c3fff57000 > > > (XEN) DMAR:[fault reason 02h] Present bit in context entry is clear > > > (XEN) print_vtd_entries: iommu = ffff83013fffaee0 bdf = 5:8.0 gmfn > > > 207498 > > > (XEN) root_entry = ffff83013ff37000 > > > (XEN) root_entry[5] = 13cf12001 > > > (XEN) context = ffff83013cf12000 > > > (XEN) context[40] = 0_0 > > > (XEN) ctxt_entry[40] not present > > > (XEN) [VT-D]iommu.c:821: iommu_fault_status: Primary Pending Fault > > > (XEN) [VT-D]iommu.c:796: DMAR:[DMA Write] Request device [05:08.0] fault > > > addr 2049d1000, iommu reg = ffff82c3fff57000 > > > (XEN) DMAR:[fault reason 02h] Present bit in context entry is clear > > > (XEN) print_vtd_entries: iommu = ffff83013fffaee0 bdf = 5:8.0 gmfn > > > 2049d1 > > > (XEN) root_entry = ffff83013ff37000 > > > (XEN) root_entry[5] = 13cf12001 > > > (XEN) context = ffff83013cf12000 > > > (XEN) context[40] = 0_0 > > > (XEN) ctxt_entry[40] not present > > > (XEN) [VT-D]iommu.c:821: iommu_fault_status: Primary Pending Fault > > > (XEN) [VT-D]iommu.c:796: DMAR:[DMA Write] Request device [05:08.0] fault > > > addr 20488e000, iommu reg = ffff82c3fff57000 > > > (XEN) DMAR:[fault reason 02h] Present bit in context entry is clear > > > (XEN) print_vtd_entries: iommu = ffff83013fffaee0 bdf = 5:8.0 gmfn > > > 20488e > > > (XEN) root_entry = ffff83013ff37000 > > > (XEN) root_entry[5] = 13cf12001 > > > (XEN) context = ffff83013cf12000 > > > (XEN) context[40] = 0_0 > > > (XEN) ctxt_entry[40] not present > > > (XEN) [VT-D]iommu.c:821: iommu_fault_status: Primary Pending Fault > > > (XEN) [VT-D]iommu.c:796: DMAR:[DMA Write] Request device [05:08.0] fault > > > addr 205495000, iommu reg = ffff82c3fff57000 > > > (XEN) DMAR:[fault reason 02h] Present bit in context entry is clear > > > (XEN) print_vtd_entries: iommu = ffff83013fffaee0 bdf = 5:8.0 gmfn > > > 205495 > > > (XEN) root_entry = ffff83013ff37000 > > > (XEN) root_entry[5] = 13cf12001 > > > (XEN) context = ffff83013cf12000 > > > (XEN) context[40] = 0_0 > > > (XEN) ctxt_entry[40] not present > > > (XEN) [VT-D]iommu.c:821: iommu_fault_status: Primary Pending Fault > > > (XEN) [VT-D]iommu.c:796: DMAR:[DMA Write] Request device [05:08.0] fault > > > addr 2072d8000, iommu reg = ffff82c3fff57000 > > > (XEN) DMAR:[fault reason 02h] Present bit in context entry is clear > > > (XEN) print_vtd_entries: iommu = ffff83013fffaee0 bdf = 5:8.0 gmfn > > > 2072d8 > > > (XEN) root_entry = ffff83013ff37000 > > > (XEN) root_entry[5] = 13cf12001 > > > (XEN) context = ffff83013cf12000 > > > (XEN) context[40] = 0_0 > > > (XEN) ctxt_entry[40] not present > > > (XEN) [VT-D]iommu.c:821: iommu_fault_status: Primary Pending Fault > > > (XEN) [VT-D]iommu.c:796: DMAR:[DMA Write] Request device [05:08.0] fault > > > addr 2055ae000, iommu reg = ffff82c3fff57000 > > > (XEN) DMAR:[fault reason 02h] Present bit in context entry is clear > > > (XEN) print_vtd_entries: iommu = ffff83013fffaee0 bdf = 5:8.0 gmfn > > > 2055ae > > > (XEN) root_entry = ffff83013ff37000 > > > (XEN) root_entry[5] = 13cf12001 > > > (XEN) context = ffff83013cf12000 > > > (XEN) context[40] = 0_0 > > > (XEN) ctxt_entry[40] not present > > > (XEN) [VT-D]iommu.c:821: iommu_fault_status: Primary Pending Fault > > > (XEN) [VT-D]iommu.c:796: DMAR:[DMA Write] Request device [05:08.0] fault > > > addr 205544000, iommu reg = ffff82c3fff57000 > > > (XEN) DMAR:[fault reason 02h] Present bit in context entry is clear > > > (XEN) print_vtd_entries: iommu = ffff83013fffaee0 bdf = 5:8.0 gmfn > > > 205544 > > > (XEN) root_entry = ffff83013ff37000 > > > (XEN) root_entry[5] = 13cf12001 > > > (XEN) context = ffff83013cf12000 > > > (XEN) context[40] = 0_0 > > > (XEN) ctxt_entry[40] not present > > > (XEN) [VT-D]iommu.c:796: DMAR:[DMA Write] Request device [05:08.0] fault > > > addr 204865000, iommu reg = ffff82c3fff57000 > > > (XEN) DMAR:[fault reason 02h] Present bit in context entry is clear > > > (XEN) print_vtd_entries: iommu = ffff83013fffaee0 bdf = 5:8.0 gmfn > > > 204865 > > > (XEN) root_entry = ffff83013ff37000 > > > (XEN) root_entry[5] = 13cf12001 > > > (XEN) context = ffff83013cf12000 > > > (XEN) context[40] = 0_0 > > > (XEN) ctxt_entry[40] not present > > > (XEN) [VT-D]iommu.c:821: iommu_fault_status: Primary Pending Fault > > > (XEN) [VT-D]iommu.c:796: DMAR:[DMA Write] Request device [05:08.0] fault > > > addr 2074be000, iommu reg = ffff82c3fff57000 > > > (XEN) DMAR:[fault reason 02h] Present bit in context entry is clear > > > (XEN) print_vtd_entries: iommu = ffff83013fffaee0 bdf = 5:8.0 gmfn > > > 2074be > > > (XEN) root_entry = ffff83013ff37000 > > > (XEN) root_entry[5] = 13cf12001 > > > (XEN) context = ffff83013cf12000 > > > (XEN) context[40] = 0_0 > > > (XEN) ctxt_entry[40] not present > > > > > > (XEN) [VT-D]iommu.c:796: DMAR:[DMA Write] Request device [05:08.0] fault > > > addr 204865000, iommu reg = ffff82c3fff57000 > > > (XEN) DMAR:[fault reason 02h] Present bit in context entry is clear > > > (XEN) print_vtd_entries: iommu = ffff83013fffaee0 bdf = 5:8.0 gmfn > > > 204865 > > > (XEN) root_entry = ffff83013ff37000 > > > (XEN) root_entry[5] = 13cf12001 > > > (XEN) context = ffff83013cf12000 > > > (XEN) context[40] = 0_0 > > > (XEN) ctxt_entry[40] not present > > > (XEN) [VT-D]iommu.c:821: iommu_fault_status: Primary Pending Fault > > > (XEN) [VT-D]iommu.c:796: DMAR:[DMA Write] Request device [05:08.0] fault > > > addr 2074be000, iommu reg = ffff82c3fff57000 > > > (XEN) DMAR:[fault reason 02h] Present bit in context entry is clear > > > (XEN) print_vtd_entries: iommu = ffff83013fffaee0 bdf = 5:8.0 gmfn > > > 2074be > > > (XEN) root_entry = ffff83013ff37000 > > > (XEN) root_entry[5] = 13cf12001 > > > (XEN) context = ffff83013cf12000 > > > (XEN) context[40] = 0_0 > > > (XEN) ctxt_entry[40] not present > > > > > > (XEN) [VT-D]iommu.c:796: DMAR:[DMA Write] Request device [05:08.0] fault > > > addr 204865000, iommu reg = ffff82c3fff57000 > > > (XEN) DMAR:[fault reason 02h] Present bit in context entry is clear > > > (XEN) print_vtd_entries: iommu = ffff83013fffaee0 bdf = 5:8.0 gmfn > > > 204865 > > > (XEN) root_entry = ffff83013ff37000 > > > (XEN) root_entry[5] = 13cf12001 > > > (XEN) context = ffff83013cf12000 > > > (XEN) context[40] = 0_0 > > > (XEN) ctxt_entry[40] not present > > > (XEN) [VT-D]iommu.c:821: iommu_fault_status: Primary Pending Fault > > > (XEN) [VT-D]iommu.c:796: DMAR:[DMA Write] Request device [05:08.0] fault > > > addr 2074be000, iommu reg = ffff82c3fff57000 > > > (XEN) DMAR:[fault reason 02h] Present bit in context entry is clear > > > (XEN) print_vtd_entries: iommu = ffff83013fffaee0 bdf = 5:8.0 gmfn > > > 2074be > > > (XEN) root_entry = ffff83013ff37000 > > > (XEN) root_entry[5] = 13cf12001 > > > (XEN) context = ffff83013cf12000 > > > (XEN) context[40] = 0_0 > > > (XEN) ctxt_entry[40] not present > > > > > > (XEN) [VT-D]iommu.c:796: DMAR:[DMA Write] Request device [05:08.0] fault > > > addr 204865000, iommu reg = ffff82c3fff57000 > > > (XEN) DMAR:[fault reason 02h] Present bit in context entry is clear > > > (XEN) print_vtd_entries: iommu = ffff83013fffaee0 bdf = 5:8.0 gmfn > > > 204865 > > > (XEN) root_entry = ffff83013ff37000 > > > (XEN) root_entry[5] = 13cf12001 > > > (XEN) context = ffff83013cf12000 > > > (XEN) context[40] = 0_0 > > > (XEN) ctxt_entry[40] not present > > > (XEN) [VT-D]iommu.c:821: iommu_fault_status: Primary Pending Fault > > > (XEN) [VT-D]iommu.c:796: DMAR:[DMA Write] Request device [05:08.0] fault > > > addr 2074be000, iommu reg = ffff82c3fff57000 > > > (XEN) DMAR:[fault reason 02h] Present bit in context entry is clear > > > (XEN) print_vtd_entries: iommu = ffff83013fffaee0 bdf = 5:8.0 gmfn > > > 2074be > > > (XEN) root_entry = ffff83013ff37000 > > > (XEN) root_entry[5] = 13cf12001 > > > (XEN) context = ffff83013cf12000 > > > (XEN) context[40] = 0_0 > > > (XEN) ctxt_entry[40] not present > > > > > > (XEN) [VT-D]iommu.c:796: DMAR:[DMA Write] Request device [05:08.0] fault > > > addr 204865000, iommu reg = ffff82c3fff57000 > > > (XEN) DMAR:[fault reason 02h] Present bit in context entry is clear > > > (XEN) print_vtd_entries: iommu = ffff83013fffaee0 bdf = 5:8.0 gmfn > > > 204865 > > > (XEN) root_entry = ffff83013ff37000 > > > (XEN) root_entry[5] = 13cf12001 > > > (XEN) context = ffff83013cf12000 > > > (XEN) context[40] = 0_0 > > > (XEN) ctxt_entry[40] not present > > > (XEN) [VT-D]iommu.c:821: iommu_fault_status: Primary Pending Fault > > > (XEN) [VT-D]iommu.c:796: DMAR:[DMA Write] Request device [05:08.0] fault > > > addr 2074be000, iommu reg = ffff82c3fff57000 > > > (XEN) DMAR:[fault reason 02h] Present bit in context entry is clear > > > (XEN) print_vtd_entries: iommu = ffff83013fffaee0 bdf = 5:8.0 gmfn > > > 2074be > > > (XEN) root_entry = ffff83013ff37000 > > > (XEN) root_entry[5] = 13cf12001 > > > (XEN) context = ffff83013cf12000 > > > (XEN) context[40] = 0_0 > > > (XEN) ctxt_entry[40] not present > > > > > > (XEN) [VT-D]iommu.c:796: DMAR:[DMA Write] Request device [05:08.0] fault > > > addr 204865000, iommu reg = ffff82c3fff57000 > > > (XEN) DMAR:[fault reason 02h] Present bit in context entry is clear > > > (XEN) print_vtd_entries: iommu = ffff83013fffaee0 bdf = 5:8.0 gmfn > > > 204865 > > > (XEN) root_entry = ffff83013ff37000 > > > (XEN) root_entry[5] = 13cf12001 > > > (XEN) context = ffff83013cf12000 > > > (XEN) context[40] = 0_0 > > > (XEN) ctxt_entry[40] not present > > > (XEN) [VT-D]iommu.c:821: iommu_fault_status: Primary Pending Fault > > > (XEN) [VT-D]iommu.c:796: DMAR:[DMA Write] Request device [05:08.0] fault > > > addr 2074be000, iommu reg = ffff82c3fff57000 > > > (XEN) DMAR:[fault reason 02h] Present bit in context entry is clear > > > (XEN) print_vtd_entries: iommu = ffff83013fffaee0 bdf = 5:8.0 gmfn > > > 2074be > > > (XEN) root_entry = ffff83013ff37000 > > > (XEN) root_entry[5] = 13cf12001 > > > (XEN) context = ffff83013cf12000 > > > (XEN) context[40] = 0_0 > > > (XEN) ctxt_entry[40] not present > > > > > > (XEN) [VT-D]iommu.c:796: DMAR:[DMA Write] Request device [05:08.0] fault > > > addr 204865000, iommu reg = ffff82c3fff57000 > > > (XEN) DMAR:[fault reason 02h] Present bit in context entry is clear > > > (XEN) print_vtd_entries: iommu = ffff83013fffaee0 bdf = 5:8.0 gmfn > > > 204865 > > > (XEN) root_entry = ffff83013ff37000 > > > (XEN) root_entry[5] = 13cf12001 > > > (XEN) context = ffff83013cf12000 > > > (XEN) context[40] = 0_0 > > > (XEN) ctxt_entry[40] not present > > > (XEN) [VT-D]iommu.c:821: iommu_fault_status: Primary Pending Fault > > > (XEN) [VT-D]iommu.c:796: DMAR:[DMA Write] Request device [05:08.0] fault > > > addr 2074be000, iommu reg = ffff82c3fff57000 > > > (XEN) DMAR:[fault reason 02h] Present bit in context entry is clear > > > (XEN) print_vtd_entries: iommu = ffff83013fffaee0 bdf = 5:8.0 gmfn > > > 2074be > > > (XEN) root_entry = ffff83013ff37000 > > > (XEN) root_entry[5] = 13cf12001 > > > (XEN) context = ffff83013cf12000 > > > (XEN) context[40] = 0_0 > > > (XEN) ctxt_entry[40] not present > > > > > > (XEN) context[40] = 0_0 > > > (XEN) ctxt_entry[40] not present > > > (XEN) [VT-D]iommu.c:796: DMAR:[DMA Write] Request device [05:08.0] fault > > > addr 204865000, iommu reg = ffff82c3fff57000 > > > (XEN) DMAR:[fault reason 02h] Present bit in context entry is clear > > > (XEN) print_vtd_entries: iommu = ffff83013fffaee0 bdf = 5:8.0 gmfn > > > 204865 > > > (XEN) root_entry = ffff83013ff37000 > > > (XEN) root_entry[5] = 13cf12001 > > > (XEN) context = ffff83013cf12000 > > > (XEN) context[40] = 0_0 > > > (XEN) ctxt_entry[40] not present > > > (XEN) [VT-D]iommu.c:821: iommu_fault_status: Primary Pending Fault > > > (XEN) [VT-D]iommu.c:796: DMAR:[DMA Write] Request device [05:08.0] fault > > > addr 2074be000, iommu reg = ffff82c3fff57000 > > > (XEN) DMAR:[fault reason 02h] Present bit in context entry is clear > > > (XEN) print_vtd_entries: iommu = ffff83013fffaee0 bdf = 5:8.0 gmfn > > > 2074be > > > (XEN) root_entry = ffff83013ff37000 > > > (XEN) root_entry[5] = 13cf12001 > > > (XEN) context = ffff83013cf12000 > > > (XEN) context[40] = 0_0 > > > (XEN) ctxt_entry[40] not present > > > > > > (XEN) context[40] = 0_0 > > > (XEN) ctxt_entry[40] not present > > > (XEN) [VT-D]iommu.c:796: DMAR:[DMA Write] Request device [05:08.0] fault > > > addr 204865000, iommu reg = ffff82c3fff57000 > > > (XEN) DMAR:[fault reason 02h] Present bit in context entry is clear > > > (XEN) print_vtd_entries: iommu = ffff83013fffaee0 bdf = 5:8.0 gmfn > > > 204865 > > > (XEN) root_entry = ffff83013ff37000 > > > (XEN) root_entry[5] = 13cf12001 > > > (XEN) context = ffff83013cf12000 > > > (XEN) context[40] = 0_0 > > > (XEN) ctxt_entry[40] not present > > > (XEN) [VT-D]iommu.c:821: iommu_fault_status: Primary Pending Fault > > > (XEN) [VT-D]iommu.c:796: DMAR:[DMA Write] Request device [05:08.0] fault > > > addr 2074be000, iommu reg = ffff82c3fff57000 > > > (XEN) DMAR:[fault reason 02h] Present bit in context entry is clear > > > (XEN) print_vtd_entries: iommu = ffff83013fffaee0 bdf = 5:8.0 gmfn > > > 2074be > > > (XEN) root_entry = ffff83013ff37000 > > > (XEN) root_entry[5] = 13cf12001 > > > (XEN) context = ffff83013cf12000 > > > (XEN) context[40] = 0_0 > > > (XEN) ctxt_entry[40] not present > > > > > > (XEN) context[40] = 0_0 > > > (XEN) ctxt_entry[40] not present > > > (XEN) [VT-D]iommu.c:796: DMAR:[DMA Write] Request device [05:08.0] fault > > > addr 204865000, iommu reg = ffff82c3fff57000 > > > (XEN) DMAR:[fault reason 02h] Present bit in context entry is clear > > > (XEN) print_vtd_entries: iommu = ffff83013fffaee0 bdf = 5:8.0 gmfn > > > 204865 > > > (XEN) root_entry = ffff83013ff37000 > > > (XEN) root_entry[5] = 13cf12001 > > > (XEN) context = ffff83013cf12000 > > > (XEN) context[40] = 0_0 > > > (XEN) ctxt_entry[40] not present > > > (XEN) [VT-D]iommu.c:821: iommu_fault_status: Primary Pending Fault > > > (XEN) [VT-D]iommu.c:796: DMAR:[DMA Write] Request device [05:08.0] fault > > > addr 2074be000, iommu reg = ffff82c3fff57000 > > > (XEN) DMAR:[fault reason 02h] Present bit in context entry is clear > > > (XEN) print_vtd_entries: iommu = ffff83013fffaee0 bdf = 5:8.0 gmfn > > > 2074be > > > (XEN) root_entry = ffff83013ff37000 > > > (XEN) root_entry[5] = 13cf12001 > > > (XEN) context = ffff83013cf12000 > > > (XEN) context[40] = 0_0 > > > (XEN) ctxt_entry[40] not present > > > > > > (XEN) context[40] = 0_0 > > > (XEN) ctxt_entry[40] not present > > > (XEN) [VT-D]iommu.c:796: DMAR:[DMA Write] Request device [05:08.0] fault > > > addr 204865000, iommu reg = ffff82c3fff57000 > > > (XEN) DMAR:[fault reason 02h] Present bit in context entry is clear > > > (XEN) print_vtd_entries: iommu = ffff83013fffaee0 bdf = 5:8.0 gmfn > > > 204865 > > > (XEN) root_entry = ffff83013ff37000 > > > (XEN) root_entry[5] = 13cf12001 > > > (XEN) context = ffff83013cf12000 > > > (XEN) context[40] = 0_0 > > > (XEN) ctxt_entry[40] not present > > > (XEN) [VT-D]iommu.c:821: iommu_fault_status: Primary Pending Fault > > > (XEN) [VT-D]iommu.c:796: DMAR:[DMA Write] Request device [05:08.0] fault > > > addr 2074be000, iommu reg = ffff82c3fff57000 > > > (XEN) DMAR:[fault reason 02h] Present bit in context entry is clear > > > (XEN) print_vtd_entries: iommu = ffff83013fffaee0 bdf = 5:8.0 gmfn > > > 2074be > > > (XEN) root_entry = ffff83013ff37000 > > > (XEN) root_entry[5] = 13cf12001 > > > (XEN) context = ffff83013cf12000 > > > (XEN) context[40] = 0_0 > > > (XEN) ctxt_entry[40] not present > > > > > > > > > _______________________________________________ > > > Xen-devel mailing list > > > Xen-devel@lists.xensource.com > > > http://lists.xensource.com/xen-devel >_______________________________________________ Xen-devel mailing list Xen-devel@lists.xensource.com http://lists.xensource.com/xen-devel
Konrad Rzeszutek Wilk
2010-Jun-01 15:25 UTC
Re: [Xen-devel] iommuu/vt-d issues with LSI MegaSAS (PERC5i)
.. snip ..> (XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = 0:1f.2 > (XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = 0:1f.3 > (XEN) [VT-D]iommu.c:1325: d0:PCIe: map bdf = 1:0.0 > (XEN) [VT-D]iommu.c:1325: d0:PCIe: map bdf = 3:0.0 > (XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = 5:e.0Good, the entry is there ..> (XEN) PCI add device 05:0e.0.. and the kernel notifies Xen that it is going to use it. But then when it tries to do DMA operations:> Already setup the GSI :18 > megaraid_sas 0000:05:0e.0: PCI INT A -> GSI 18 (level, low) -> IRQ 18 > megasas: FW now in Ready state > calling e1000_init_module+0x0/0(XEN) [VT-D]iommu.c:821: > iommu_fault_status: Primary Pending Fault > x70 [e1000e] @ 6(XEN) [VT-D]iommu.c:796: DMAR:[DMA Write] Request device > [05:08.0] fault addr 2d0842000, iommu reg = ffff82c3fff57000 > (XEN) DMAR:[fault reason 02h] Present bit in context entry is clear > 76 > (XEN) print_vtd_entries: iommu = ffff83013ff7b130 bdf = 5:8.0 gmfn > 2d0842 > scsi6 : LSI SAS (XEN) root_entry = ffff83013ff37000 > based MegaRAID d(XEN) root_entry[5] = 13cf13001 > river > (XEN) context = ffff83013cf13000 > initcall megasas(XEN) context[40] = 0_0 > _init+0x0/0x16f (XEN) ctxt_entry[40] not present > [megaraid_sas] r(XEN) [VT-D]iommu.c:821: iommu_fault_status: Primary > Pending Fault > eturned 0 after (XEN) [VT-D]iommu.c:796: DMAR:[DMA Write] Request device > [05:08.0] fault addr 2d0842000, iommu reg = ffff82c3fff57000 > (XEN) DMAR:[fault reason 02h] Present bit in context entry is clear > 73201 usecs > (XEN) print_vtd_entries: iommu = ffff83013ff7b130 bdf = 5:8.0 gmfn > 2d0842 > scsi scan: INQUI(XEN) root_entry = ffff83013ff37000 > RY result too sh(XEN) root_entry[5] = 13cf13001 > ort (5), using 3(XEN) context = ffff83013cf13000 > 6 > (XEN) context[40] = 0_0 > scsi 6:0:0:0: Di(XEN) ctxt_entry[40] not present > rect-Access PQ: 0 ANSI: 0 > scsi scan: INQUIRY result too short (5), using 36 > scsi 6:0:1:0: Direct-Access PQ: 0 > ANSI: 0 > scsi scan: INQUIRY result too short (5), using 36 > scsi 6:0:2:0: Direct-Access PQ: 0 > ANSI: 0 > scsi scan: INQUIRY result too short (5), using 36 > scsi 6:0:3:0: Direct-Access PQ: 0 > ANSI: 0 > scsi 6:2:0:0: Direct-Access DELL PERC 5/i 1.03 PQ: 0 > ANSI: 5 > e1000e: Intel(R) PRO/1000 Network Driver - 1.0.2-k2 > e1000e: Copyright (c) 1999-2008 Intel Corporation. > e1000e 0000:07:00.0: Disabling L1 ASPM > xen: registering gsi 16 triggering 0 polarity 1 > xen_allocate_pirq: returning irq 16 for gsi 16 > xen: --> irq=16 > Already setup the GSI :16 > e1000e 0000:07:00.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16 > e1000e 0000:07:00.0: setting latency timer to 64 > alloc irq_desc for 4260 on node 0 > alloc kstat_irqs on node 0 > alloc irq_desc for 4259 on node 0 > alloc kstat_irqs on node 0 > alloc irq_desc for 4258 on node 0 > sd 6:2:0:0: Attached scsi generic sg2 type 0 > scsi_scan_6 used(XEN) [VT-D]iommu.c:821: iommu_fault_status: Primary > Pending Fault > greatest stack (XEN) [VT-D]iommu.c:796: DMAR:[DMA Write] Request device > [05:08.0] fault addr 2cfa6e000, iommu reg = ffff82c3fff57000 > (XEN) DMAR:[fault reason 02h] Present bit in context entry is clear > depth: 4088 byte(XEN) print_vtd_entries: iommu = ffff83013ff7b130 bdf > 5:8.0 gmfn = 2cfa6e > s left > (XEN) root_entry = ffff83013ff37000 > sd 6:2:0:0: [sdb(XEN) root_entry[5] = 13cf13001 > ] 211550208 512-(XEN) context = ffff83013cf13000 > byte logical blo(XEN) context[40] = 0_0 > cks: (108 GB/100(XEN) ctxt_entry[40] not present > GiB) > sd 6:2:0:0: [sdb] Write Protect is off > sd 6:2:0:0: [sdb] Mode Sense: 1f 00 00 08 > sd 6:2:0:0: [sdb] Write cache: disabled, read cache: enabled, doesn''t > support DPO or FUA > sdb: unknown partition table > alloc kstat_irqs on node 0 > sd 6:2:0:0: [sdb] Attached SCSI diskAnd here the driver sends the SCSI INQUIRY command and they are truncated. Which probably means that the page where the data was expected never got any data (which is exactly what the VT-d chipset did since it does not have a entry for that page and canceled the DMA operation). So, Xen prints it out and confirms this: we get "ctxt_entry[40] not present" which means that there hasn''t been an entry for it. And root_entry[5] is set to 13cf13001, which is definitely above the 4GB mark. The Xen hypervisor looks to be setting 1:1 mapping for every page up to ''max_page'', which is the max page (would be ~2937039) so it would include the 4GB. (iommu_set_dom0_mapping code in rivers/passthrough/vtd/x86/vtd.c). and the 13cf13001 is within the E820 entry for RAM, so it _ought_ to have an entry. I can think of four things: 1). The driver is buggy. It is using the wrong DMA address. This can be verified if you do two things: compile your pv_ops kernel with CONFIG_DMAR and boot it bare metal. 2). The mapping in Xen VT-D IOMMU code for 4GB is somehow busted. You can check that by including two options on your Linux kernel line: "iommu=soft swiotlb=force". Or you can make Dom0 have a limited amount of memory by setting this on your Xen line: ''dom0_mem=max:4GB'' which will limit Dom0 to only 4GB. 3). Maybe the hardware is busted? 4). CC-ing the Intel folks. They might have some ideas here too. Also my analysis could be flawed - the hardware I have is busted so I only know of non-working conditions :-( _______________________________________________ Xen-devel mailing list Xen-devel@lists.xensource.com http://lists.xensource.com/xen-devel
Kay, Allen M
2010-Jun-01 18:46 UTC
RE: [Xen-devel] iommuu/vt-d issues with LSI MegaSAS (PERC5i)
Base on the following two pieces of information, it looks like device 05:08.0 is not PCI visible but is generating DMA traffic. 1)> > (XEN) [VT-D]iommu.c:821: iommu_fault_status: Primary Pending Fault > > (XEN) [VT-D]iommu.c:796: DMAR:[DMA Write] Request device [05:08.0] fault > > addr 203a09000, iommu reg = ffff82c3fff57000 > > (XEN) DMAR:[fault reason 02h] Present bit in context entry is clear > > (XEN) print_vtd_entries: iommu = ffff83013fffaee0 bdf = 5:8.0 gmfn > > 203a09 > > (XEN) root_entry = ffff83013ff37000 > > (XEN) root_entry[5] = 13cf12001 > > (XEN) context = ffff83013cf12000 > > (XEN) context[40] = 0_0 > > (XEN) ctxt_entry[40] not present2)> > (XEN) PCI add device 00:00.0 > > (XEN) PCI add device 00:01.0 > > (XEN) PCI add device 00:03.0 > > (XEN) PCI add device 00:07.0 > > (XEN) PCI add device 00:14.0 > > (XEN) PCI add device 00:14.1 > > (XEN) PCI add device 00:14.2 > > (XEN) PCI add device 00:14.3 > > (XEN) PCI add device 00:16.0 > > (XEN) PCI add device 00:16.1 > > (XEN) PCI add device 00:16.2 > > (XEN) PCI add device 00:16.3 > > (XEN) PCI add device 00:16.4 > > (XEN) PCI add device 00:16.5 > > (XEN) PCI add device 00:16.6 > > (XEN) PCI add device 00:16.7 > > (XEN) PCI add device 00:1a.0 > > (XEN) PCI add device 00:1a.1 > > (XEN) PCI add device 00:1a.2 > > (XEN) PCI add device 00:1a.7 > > (XEN) PCI add device 00:1b.0 > > (XEN) PCI add device 00:1c.0 > > (XEN) PCI add device 00:1c.4 > > (XEN) PCI add device 00:1c.5 > > (XEN) PCI add device 00:1d.0 > > (XEN) PCI add device 00:1d.1 > > (XEN) PCI add device 00:1d.2 > > (XEN) PCI add device 00:1d.7 > > (XEN) PCI add device 00:1e.0 > > (XEN) PCI add device 00:1f.0 > > (XEN) PCI add device 00:1f.2 > > (XEN) PCI add device 00:1f.3 > > (XEN) PCI add device 01:00.0 > > (XEN) PCI add device 03:00.0 > > (XEN) PCI add device 04:00.0 > > (XEN) PCI add device 04:00.2 > > (XEN) PCI add device 05:0e.0 > > (XEN) PCI add device 07:00.0 > > (XEN) PCI add device 08:00.0-----Original Message----- From: xen-devel-bounces@lists.xensource.com [mailto:xen-devel-bounces@lists.xensource.com] On Behalf Of M. Nunberg Sent: Sunday, May 30, 2010 11:33 AM To: Pasi Kärkkäinen Cc: xen-devel@lists.xensource.com Subject: Re: [Xen-devel] iommuu/vt-d issues with LSI MegaSAS (PERC5i) Here is the full log, kernel + xen \ \/ /___ _ __ | || | / _ \ / | _ __ ___/ | \ // _ \ '_ \ | || |_| | | || |__| '__/ __| | / \ __/ | | | |__ _| |_| || |__| | | (__| | /_/\_\___|_| |_| |_|(_)___(_)_| |_| \___|_| (XEN) Xen version 4.0.1-rc1 (mordy@) (gcc version 4.3.2 (Debian 4.3.2-1.1) ) Fri May 28 16:46:04 PDT 2010 (XEN) Latest ChangeSet: Sat May 22 07:18:16 2010 +0100 21162:370fd9f97c70 (XEN) Console output is synchronous. (XEN) Command line: iommu=verbose loglvl=all guest_loglvl=all sync_console console_to_rint com1=115200,8n1 console=com1 (XEN) Video information: (XEN) VGA is text mode 80x25, font 8x16 (XEN) VBE/DDC methods: none; EDID transfer time: 0 seconds (XEN) EDID info not retrieved because no DDC retrieval method detected (XEN) Disc information: (XEN) Found 1 MBR signatures (XEN) Found 1 EDD information structures (XEN) Xen-e820 RAM map: (XEN) 0000000000000000 - 000000000009a000 (usable) (XEN) 000000000009a000 - 00000000000a0000 (reserved) (XEN) 00000000000e0000 - 0000000000100000 (reserved) (XEN) 0000000000100000 - 00000000bf760000 (usable) (XEN) 00000000bf76e000 - 00000000bf770000 type 9 (XEN) 00000000bf770000 - 00000000bf77e000 (ACPI data) (XEN) 00000000bf77e000 - 00000000bf7d0000 (ACPI NVS) (XEN) 00000000bf7d0000 - 00000000bf7e0000 (reserved) (XEN) 00000000bf7ec000 - 00000000c0000000 (reserved) (XEN) 00000000fee00000 - 00000000fee01000 (reserved) (XEN) 00000000ffc00000 - 0000000100000000 (reserved) (XEN) 0000000100000000 - 0000000340000000 (usable) (XEN) ACPI: RSDP 000F9E10, 0024 (r2 ACPIAM) (XEN) ACPI: XSDT BF770100, 0094 (r1 NEC 20090424 MSFT 97) (XEN) ACPI: FACP BF770290, 00F4 (r4 042409 FACP1917 20090424 MSFT 97) (XEN) ACPI: DSDT BF770670, 5BFB (r2 10601 10601000 0 INTL 20051117) (XEN) ACPI: FACS BF77E000, 0040 (XEN) ACPI: APIC BF770390, 00D2 (r2 042409 APIC1917 20090424 MSFT 97) (XEN) ACPI: MCFG BF770470, 003C (r1 042409 OEMMCFG 20090424 MSFT 97) (XEN) ACPI: SLIC BF7704B0, 0176 (r1 NEC 20090424 MSFT 97) (XEN) ACPI: ERST BF770630, 0040 (r1 042409 WHEA1917 20090424 MSFT 97) (XEN) ACPI: OEMB BF77E040, 007B (r1 042409 OEMB1917 20090424 MSFT 97) (XEN) ACPI: SRAT BF77A670, 01D0 (r1 042409 OEMSRAT 1 INTL 1) (XEN) ACPI: HPET BF77A840, 0038 (r1 042409 OEMHPET 20090424 MSFT 97) (XEN) ACPI: DMAR BF77E0C0, 0118 (r1 AMI OEMDMAR 1 MSFT 97) (XEN) ACPI: SSDT BF781DF0, 0363 (r1 DpgPmm CpuPm 12 INTL 20051117) (XEN) ACPI: EINJ BF77A880, 0130 (r1 AMIER AMI_EINJ 20090424 MSFT 97) (XEN) ACPI: BERT BF77AA10, 0030 (r1 AMIER AMI_BERT 20090424 MSFT 97) (XEN) ACPI: ERST BF77AA40, 01B0 (r1 AMIER AMI_ERST 20090424 MSFT 97) (XEN) ACPI: HEST BF77ABF0, 00A8 (r1 AMIER AMI_HEST 20090424 MSFT 97) (XEN) System RAM: 12278MB (12573672kB) (XEN) SRAT: PXM 0 -> APIC 0 -> Node 0 (XEN) SRAT: PXM 0 -> APIC 2 -> Node 0 (XEN) SRAT: PXM 0 -> APIC 4 -> Node 0 (XEN) SRAT: PXM 0 -> APIC 6 -> Node 0 (XEN) SRAT: PXM 0 -> APIC 1 -> Node 0 (XEN) SRAT: PXM 0 -> APIC 3 -> Node 0 (XEN) SRAT: PXM 0 -> APIC 5 -> Node 0 (XEN) SRAT: PXM 0 -> APIC 7 -> Node 0 (XEN) SRAT: PXM 1 -> APIC 16 -> Node 1 (XEN) SRAT: PXM 1 -> APIC 18 -> Node 1 (XEN) SRAT: PXM 1 -> APIC 20 -> Node 1 (XEN) SRAT: PXM 1 -> APIC 22 -> Node 1 (XEN) SRAT: PXM 1 -> APIC 17 -> Node 1 (XEN) SRAT: PXM 1 -> APIC 19 -> Node 1 (XEN) SRAT: PXM 1 -> APIC 21 -> Node 1 (XEN) SRAT: PXM 1 -> APIC 23 -> Node 1 (XEN) SRAT: Node 0 PXM 0 0-a0000 (XEN) SRAT: Node 0 PXM 0 100000-c0000000 (XEN) SRAT: Node 0 PXM 0 100000000-1c0000000 (XEN) SRAT: Node 1 PXM 1 1c0000000-340000000 (XEN) NUMA: Allocated memnodemap from 33fdfb000 - 33fdff000 (XEN) NUMA: Using 8 for the hash shift. (XEN) Domain heap initialised DMA width 30 bits (XEN) found SMP MP-table at 000ff780 (XEN) DMI present. (XEN) Using APIC driver default (XEN) ACPI: PM-Timer IO Port: 0x808 (XEN) ACPI: ACPI SLEEP INFO: pm1x_cnt[804,0], pm1x_evt[800,0] (XEN) ACPI: wakeup_vec[bf77e00c], vec_size[20] (XEN) ACPI: Local APIC address 0xfee00000 (XEN) ACPI: LAPIC (acpi_id[0x01] lapic_id[0x00] enabled) (XEN) Processor #0 7:10 APIC version 21 (XEN) ACPI: LAPIC (acpi_id[0x02] lapic_id[0x10] enabled) (XEN) Processor #16 7:10 APIC version 21 (XEN) ACPI: LAPIC (acpi_id[0x03] lapic_id[0x02] enabled) (XEN) Processor #2 7:10 APIC version 21 (XEN) ACPI: LAPIC (acpi_id[0x04] lapic_id[0x12] enabled) (XEN) Processor #18 7:10 APIC version 21 (XEN) ACPI: LAPIC (acpi_id[0x05] lapic_id[0x04] enabled) (XEN) Processor #4 7:10 APIC version 21 (XEN) ACPI: LAPIC (acpi_id[0x06] lapic_id[0x14] enabled) (XEN) Processor #20 7:10 APIC version 21 (XEN) ACPI: LAPIC (acpi_id[0x07] lapic_id[0x06] enabled) (XEN) Processor #6 7:10 APIC version 21 (XEN) ACPI: LAPIC (acpi_id[0x08] lapic_id[0x16] enabled) (XEN) Processor #22 7:10 APIC version 21 (XEN) ACPI: LAPIC (acpi_id[0x09] lapic_id[0x01] enabled) (XEN) Processor #1 7:10 APIC version 21 (XEN) ACPI: LAPIC (acpi_id[0x0a] lapic_id[0x11] enabled) (XEN) Processor #17 7:10 APIC version 21 (XEN) ACPI: LAPIC (acpi_id[0x0b] lapic_id[0x03] enabled) (XEN) Processor #3 7:10 APIC version 21 (XEN) ACPI: LAPIC (acpi_id[0x0c] lapic_id[0x13] enabled) (XEN) Processor #19 7:10 APIC version 21 (XEN) ACPI: LAPIC (acpi_id[0x0d] lapic_id[0x05] enabled) (XEN) Processor #5 7:10 APIC version 21 (XEN) ACPI: LAPIC (acpi_id[0x0e] lapic_id[0x15] enabled) (XEN) Processor #21 7:10 APIC version 21 (XEN) ACPI: LAPIC (acpi_id[0x0f] lapic_id[0x07] enabled) (XEN) Processor #7 7:10 APIC version 21 (XEN) ACPI: LAPIC (acpi_id[0x10] lapic_id[0x17] enabled) (XEN) Processor #23 7:10 APIC version 21 (XEN) ACPI: LAPIC_NMI (acpi_id[0xff] dfl dfl lint[0x1]) (XEN) Overriding APIC driver with bigsmp (XEN) ACPI: IOAPIC (id[0x08] address[0xfec00000] gsi_base[0]) (XEN) IOAPIC[0]: apic_id 8, version 32, address 0xfec00000, GSI 0-23 (XEN) ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl) (XEN) ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 20 low level) (XEN) ACPI: IRQ0 used by override. (XEN) ACPI: IRQ2 used by override. (XEN) ACPI: IRQ9 used by override. (XEN) Enabling APIC mode: Phys. Using 1 I/O APICs (XEN) ACPI: HPET id: 0xffffffff base: 0xfed00000 (XEN) [VT-D]dmar.c:679: Host address width 40 (XEN) [VT-D]dmar.c:694: found ACPI_DMAR_DRHD: (XEN) [VT-D]dmar.c:398: dmaru->address = fbffe000 (XEN) [VT-D]dmar.c:340: IOAPIC: f0:1f.7 (XEN) [VT-D]dmar.c:411: flags: INCLUDE_ALL (XEN) [VT-D]dmar.c:699: found ACPI_DMAR_RMRR: (XEN) [VT-D]dmar.c:334: endpoint: 0:1d.0 (XEN) [VT-D]dmar.c:334: endpoint: 0:1d.1 (XEN) [VT-D]dmar.c:334: endpoint: 0:1d.2 (XEN) [VT-D]dmar.c:334: endpoint: 0:1d.7 (XEN) [VT-D]dmar.c:334: endpoint: 0:1a.0 (XEN) [VT-D]dmar.c:334: endpoint: 0:1a.1 (XEN) [VT-D]dmar.c:334: endpoint: 0:1a.2 (XEN) [VT-D]dmar.c:334: endpoint: 0:1a.7 (XEN) [VT-D]dmar.c:571: RMRR region: base_addr ec000 end_address effff (XEN) [VT-D]dmar.c:699: found ACPI_DMAR_RMRR: (XEN) [VT-D]dmar.c:334: endpoint: 0:1d.0 (XEN) [VT-D]dmar.c:334: endpoint: 0:1d.1 (XEN) [VT-D]dmar.c:334: endpoint: 0:1d.2 (XEN) [VT-D]dmar.c:334: endpoint: 0:1d.7 (XEN) [VT-D]dmar.c:334: endpoint: 0:1a.0 (XEN) [VT-D]dmar.c:334: endpoint: 0:1a.1 (XEN) [VT-D]dmar.c:334: endpoint: 0:1a.2 (XEN) [VT-D]dmar.c:334: endpoint: 0:1a.7 (XEN) [VT-D]dmar.c:571: RMRR region: base_addr bf7ec000 end_address bf7fffff (XEN) [VT-D]dmar.c:704: found ACPI_DMAR_ATSR: (XEN) [VT-D]dmar.c:599: atsru->all_ports: 0 (XEN) [VT-D]dmar.c:320: bridge: 0:1.0 start = 0 sec = 1 sub = 1 (XEN) [VT-D]dmar.c:320: bridge: 0:3.0 start = 0 sec = 2 sub = 2 (XEN) [VT-D]dmar.c:320: bridge: 0:7.0 start = 0 sec = 3 sub = 3 (XEN) PCI: MCFG configuration 0: base e0000000 segment 0 buses 0 - 255 (XEN) PCI: Not using MMCONFIG. (XEN) Using ACPI (MADT) for SMP configuration information (XEN) Using scheduler: SMP Credit Scheduler (credit) (XEN) Detected 2266.784 MHz processor. (XEN) Initing memory sharing. (XEN) VMX: Supported advanced features: (XEN) - APIC MMIO access virtualisation (XEN) - APIC TPR shadow (XEN) - Extended Page Tables (EPT) (XEN) - Virtual-Processor Identifiers (VPID) (XEN) - Virtual NMI (XEN) - MSR direct-access bitmap (XEN) HVM: ASIDs enabled. (XEN) HVM: VMX enabled (XEN) HVM: Hardware Assisted Paging detected. (XEN) Intel machine check reporting enabled (XEN) [VT-D]iommu.c:1078: drhd->address = fbffe000 iommu->reg ffff82c3fff57000 (XEN) [VT-D]iommu.c:1080: cap = c90780106f0462 ecap = f0207e (XEN) Intel VT-d Snoop Control not supported. (XEN) Intel VT-d DMA Passthrough not supported. (XEN) Intel VT-d Queued Invalidation supported. (XEN) Intel VT-d Interrupt Remapping supported. (XEN) I/O virtualisation enabled (XEN) I/O virtualisation for PV guests disabled (XEN) Total of 16 processors activated. (XEN) ENABLING IO-APIC IRQs (XEN) -> Using new ACK method (XEN) ..TIMER: vector=0xF0 apic1=0 pin1=2 apic2=-1 pin2=-1 (XEN) TSC is reliable, synchronization unnecessary (XEN) Platform timer is 14.318MHz HPET ÿ(XEN) Allocated console ring of 128 KiB. (XEN) microcode.c:73:d32767 microcode: CPU1 resumed (XEN) microcode.c:73:d32767 microcode: CPU9 resumed (XEN) microcode.c:73:d32767 microcode: CPU6 resumed (XEN) microcode.c:73:d32767 microcode: CPU14 resumed (XEN) microcode.c:73:d32767 microcode: CPU7 resumed (XEN) microcode.c:73:d32767 microcode: CPU15 resumed (XEN) microcode.c:73:d32767 microcode: CPU10 resumed (XEN) microcode.c:73:d32767 microcode: CPU13 resumed (XEN) microcode.c:73:d32767 microcode: CPU5 resumed (XEN) microcode.c:73:d32767 microcode: CPU2 resumed (XEN) microcode.c:73:d32767 microcode: CPU3 resumed (XEN) microcode.c:73:d32767 microcode: CPU11 resumed (XEN) microcode.c:73:d32767 microcode: CPU12 resumed (XEN) microcode.c:73:d32767 microcode: CPU8 resumed (XEN) microcode.c:73:d32767 microcode: CPU4 resumed (XEN) Brought up 16 CPUs (XEN) Turbo Mode detected! (XEN) HPET's MSI mode hasn't been supported when Interrupt Remapping is enabled. (XEN) ACPI sleep modes: S3 (XEN) mcheck_poll: Machine check polling timer started. (XEN) [VT-D]iommu.c:1325: d0:PCIe: map bdf = 0:0.0 (XEN) [VT-D]iommu.c:1325: d0:PCIe: map bdf = 0:14.0 (XEN) [VT-D]iommu.c:1325: d0:PCIe: map bdf = 0:14.1 (XEN) [VT-D]iommu.c:1325: d0:PCIe: map bdf = 0:14.2 (XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = 0:14.3 (XEN) [VT-D]iommu.c:1325: d0:PCIe: map bdf = 0:16.0 (XEN) [VT-D]iommu.c:1325: d0:PCIe: map bdf = 0:16.1 (XEN) [VT-D]iommu.c:1325: d0:PCIe: map bdf = 0:16.2 (XEN) [VT-D]iommu.c:1325: d0:PCIe: map bdf = 0:16.3 (XEN) [VT-D]iommu.c:1325: d0:PCIe: map bdf = 0:16.4 (XEN) [VT-D]iommu.c:1325: d0:PCIe: map bdf = 0:16.5 (XEN) [VT-D]iommu.c:1325: d0:PCIe: map bdf = 0:16.6 (XEN) [VT-D]iommu.c:1325: d0:PCIe: map bdf = 0:16.7 (XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = 0:1a.0 (XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = 0:1a.1 (XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = 0:1a.2 (XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = 0:1a.7 (XEN) [VT-D]iommu.c:1325: d0:PCIe: map bdf = 0:1b.0 (XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = 0:1d.0 (XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = 0:1d.1 (XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = 0:1d.2 (XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = 0:1d.7 (XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = 0:1f.0 (XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = 0:1f.2 (XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = 0:1f.3 (XEN) [VT-D]iommu.c:1325: d0:PCIe: map bdf = 1:0.0 (XEN) [VT-D]iommu.c:1325: d0:PCIe: map bdf = 3:0.0 (XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = 5:e.0 (XEN) [VT-D]iommu.c:1325: d0:PCIe: map bdf = 7:0.0 (XEN) [VT-D]iommu.c:1325: d0:PCIe: map bdf = 8:0.0 (XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = fe:0.0 (XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = fe:0.1 (XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = fe:2.0 (XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = fe:2.1 (XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = fe:2.4 (XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = fe:2.5 (XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = fe:3.0 (XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = fe:3.1 (XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = fe:3.2 (XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = fe:3.4 (XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = fe:4.0 (XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = fe:4.1 (XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = fe:4.2 (XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = fe:4.3 (XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = fe:5.0 (XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = fe:5.1 (XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = fe:5.2 (XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = fe:5.3 (XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = fe:6.0 (XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = fe:6.1 (XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = fe:6.2 (XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = fe:6.3 (XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = ff:0.0 (XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = ff:0.1 (XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = ff:2.0 (XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = ff:2.1 (XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = ff:2.4 (XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = ff:2.5 (XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = ff:3.0 (XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = ff:3.1 (XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = ff:3.2 (XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = ff:3.4 (XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = ff:4.0 (XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = ff:4.1 (XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = ff:4.2 (XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = ff:4.3 (XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = ff:5.0 (XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = ff:5.1 (XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = ff:5.2 (XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = ff:5.3 (XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = ff:6.0 (XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = ff:6.1 (XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = ff:6.2 (XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = ff:6.3 (XEN) [VT-D]iommu.c:695: iommu_enable_translation: iommu->reg ffff82c3fff57000 (XEN) *** LOADING DOMAIN 0 *** (XEN) Xen kernel: 64-bit, lsb, compat32 (XEN) Dom0 kernel: 64-bit, PAE, lsb, paddr 0x1000000 -> 0x26b6000 (XEN) PHYSICAL MEMORY ARRANGEMENT: (XEN) Dom0 alloc.: 0000000100000000->0000000120000000 (2937039 pages to be allocated) (XEN) VIRTUAL MEMORY ARRANGEMENT: (XEN) Loaded kernel: ffffffff81000000->ffffffff826b6000 (XEN) Init. ramdisk: ffffffff826b6000->ffffffff8f7d7600 (XEN) Phys-Mach map: ffffffff8f7d8000->ffffffff90f40678 (XEN) Start info: ffffffff90f41000->ffffffff90f414b4 (XEN) Page tables: ffffffff90f42000->ffffffff90fcf000 (XEN) Boot stack: ffffffff90fcf000->ffffffff90fd0000 (XEN) TOTAL: ffffffff80000000->ffffffff91400000 (XEN) ENTRY ADDRESS: ffffffff819be200 (XEN) Dom0 has maximum 16 VCPUs (XEN) Scrubbing Free RAM: .done. (XEN) Xen trace buffers: disabled (XEN) Std. Loglevel: All (XEN) Guest Loglevel: All (XEN) ********************************************** (XEN) ******* WARNING: CONSOLE OUTPUT IS SYNCHRONOUS (XEN) ******* This option is intended to aid debugging of Xen by ensuring (XEN) ******* that all output is synchronously delivered on the serial line. (XEN) ******* However it can introduce SIGNIFICANT latencies and affect (XEN) ******* timekeeping. It is NOT recommended for production use! (XEN) ********************************************** (XEN) 3... 2... 1... (XEN) *** Serial input -> DOM0 (type 'CTRL-a' three times to switch input to Xen) (XEN) Freed 180kB init memory. mapping kernel into physical memory Xen: setup ISA identity maps about to get started... Initializing cgroup subsys cpuset Initializing cgroup subsys cpu Linux version 2.6.32.13 (mordy@debmed) (gcc version 4.3.2 (Debian 4.3.2-1.1) ) #3 SMP Fri May 28 13:20:24 PDT 2010 Command line: root=/dev/mapper/MISC-fedora ro nomodeset console=hvc0 earlyprintk=xen debug initcall_debug loglvel=10 KERNEL supported cpus: Intel GenuineIntel AMD AuthenticAMD Centaur CentaurHauls xen_release_chunk: looking at area pfn bf760-bf76e: 14 pages freed xen_release_chunk: looking at area pfn bf7e0-bf7ec: 12 pages freed xen_release_chunk: looking at area pfn c0000-fec00: 257024 pages freed xen_release_chunk: looking at area pfn fec01-fee00: 511 pages freed xen_release_chunk: looking at area pfn fee01-ffc00: 3583 pages freed released 261144 pages of unused memory BIOS-provided physical RAM map: Xen: 0000000000000000 - 000000000009a000 (usable) Xen: 000000000009a000 - 0000000000100000 (reserved) Xen: 0000000000100000 - 00000000bf760000 (usable) Xen: 00000000bf76e000 - 00000000bf770000 type 9 Xen: 00000000bf770000 - 00000000bf77e000 (ACPI data) Xen: 00000000bf77e000 - 00000000bf7d0000 (ACPI NVS) Xen: 00000000bf7d0000 - 00000000bf7e0000 (reserved) Xen: 00000000bf7ec000 - 00000000c0000000 (reserved) Xen: 00000000fec00000 - 00000000fec01000 (reserved) Xen: 00000000fee00000 - 00000000fee01000 (reserved) Xen: 00000000ffc00000 - 0000000100000000 (reserved) Xen: 0000000100000000 - 00000002ed0cf000 (usable) bootconsole [xenboot0] enabled DMI present. AMI BIOS detected: BIOS may corrupt low RAM, working around it. e820 update range: 0000000000000000 - 0000000000010000 (usable) ==> (reserved) last_pfn = 0x2ed0cf max_arch_pfn = 0x400000000 x86 PAT enabled: cpu 0, old 0x50100070406, new 0x7010600070106 last_pfn = 0xbf760 max_arch_pfn = 0x400000000 initial memory mapped : 0 - 20000000 init_memory_mapping: 0000000000000000-00000000bf760000 0000000000 - 00bf760000 page 4k kernel direct mapping tables up to bf760000 @ 100000-700000 init_memory_mapping: 0000000100000000-00000002ed0cf000 0100000000 - 02ed0cf000 page 4k kernel direct mapping tables up to 2ed0cf000 @ 10fcf000-12745000 RAMDISK: 026b6000 - 0f7d7600 ACPI: RSDP 00000000000f9e10 00024 (v02 ACPIAM) ACPI: XSDT 00000000bf770100 00094 (v01 NEC 20090424 MSFT 00000097) ACPI: FACP 00000000bf770290 000F4 (v04 042409 FACP1917 20090424 MSFT 00000097) ACPI: DSDT 00000000bf770670 05BFB (v02 10601 10601000 00000000 INTL 20051117) ACPI: FACS 00000000bf77e000 00040 ACPI: APIC 00000000bf770390 000D2 (v02 042409 APIC1917 20090424 MSFT 00000097) ACPI: MCFG 00000000bf770470 0003C (v01 042409 OEMMCFG 20090424 MSFT 00000097) ACPI: SLIC 00000000bf7704b0 00176 (v01 NEC 20090424 MSFT 00000097) ACPI: ERST 00000000bf770630 00040 (v01 042409 WHEA1917 20090424 MSFT 00000097) ACPI: OEMB 00000000bf77e040 0007B (v01 042409 OEMB1917 20090424 MSFT 00000097) ACPI: SRAT 00000000bf77a670 001D0 (v01 042409 OEMSRAT 00000001 INTL 00000001) ACPI: HPET 00000000bf77a840 00038 (v01 042409 OEMHPET 20090424 MSFT 00000097) ACPI: 00000000bf77e0c0 00118 (v01 AMI OEMDMAR 00000001 MSFT 00000097) ACPI: SSDT 00000000bf781df0 00363 (v01 DpgPmm CpuPm 00000012 INTL 20051117) ACPI: EINJ 00000000bf77a880 00130 (v01 AMIER AMI_EINJ 20090424 MSFT 00000097) ACPI: BERT 00000000bf77aa10 00030 (v01 AMIER AMI_BERT 20090424 MSFT 00000097) ACPI: ERST 00000000bf77aa40 001B0 (v01 AMIER AMI_ERST 20090424 MSFT 00000097) ACPI: HEST 00000000bf77abf0 000A8 (v01 AMIER AMI_HEST 20090424 MSFT 00000097) ACPI: Local APIC address 0xfee00000 SRAT: PXM 0 -> APIC 0 -> Node 0 SRAT: PXM 0 -> APIC 2 -> Node 0 SRAT: PXM 0 -> APIC 4 -> Node 0 SRAT: PXM 0 -> APIC 6 -> Node 0 SRAT: PXM 0 -> APIC 1 -> Node 0 SRAT: PXM 0 -> APIC 3 -> Node 0 SRAT: PXM 0 -> APIC 5 -> Node 0 SRAT: PXM 0 -> APIC 7 -> Node 0 SRAT: PXM 1 -> APIC 16 -> Node 1 SRAT: PXM 1 -> APIC 18 -> Node 1 SRAT: PXM 1 -> APIC 20 -> Node 1 SRAT: PXM 1 -> APIC 22 -> Node 1 SRAT: PXM 1 -> APIC 17 -> Node 1 SRAT: PXM 1 -> APIC 19 -> Node 1 SRAT: PXM 1 -> APIC 21 -> Node 1 SRAT: PXM 1 -> APIC 23 -> Node 1 SRAT: Node 0 PXM 0 0-a0000 SRAT: Node 0 PXM 0 100000-c0000000 SRAT: Node 0 PXM 0 100000000-1c0000000 SRAT: Node 2 PXM 257 1c0000000-340000000 NUMA: Allocated memnodemap from 10000 - 16840 NUMA: Using 20 for the hash shift. Bootmem setup node 0 0000000000000000-00000001c0000000 NODE_DATA [0000000000016840 - 000000000002e83f] bootmap [000000000002f000 - 0000000000066fff] pages 38 (10 early reservations) ==> bootmem [0000000000 - 01c0000000] #0 [0000000000 - 0000001000] BIOS data page ==> [0000000000 - 0000001000] #1 [0010f42000 - 0010fcf000] XEN PAGETABLES ==> [0010f42000 - 0010fcf000] #2 [0000006000 - 0000008000] TRAMPOLINE ==> [0000006000 - 0000008000] #3 [0001000000 - 0002695878] TEXT DATA BSS ==> [0001000000 - 0002695878] #4 [00026b6000 - 000f7d7600] RAMDISK ==> [00026b6000 - 000f7d7600] #5 [000f7d8000 - 0010f42000] XEN START INFO ==> [000f7d8000 - 0010f42000] #6 [0002696000 - 0002696149] BRK ==> [0002696000 - 0002696149] #7 [0000100000 - 0000670000] PGTABLE ==> [0000100000 - 0000670000] #8 [0010fcf000 - 0011f40000] PGTABLE ==> [0010fcf000 - 0011f40000] #9 [0000010000 - 0000016840] MEMNODEMAP ==> [0000010000 - 0000016840] Bootmem setup node 2 00000001c0000000-00000002ed0cf000 NODE_DATA [00000001c0000000 - 00000001c0017fff] bootmap [00000001c0018000 - 00000001c003da1f] pages 26 (10 early reservations) ==> bootmem [01c0000000 - 02ed0cf000] #0 [0000000000 - 0000001000] BIOS data page #1 [0010f42000 - 0010fcf000] XEN PAGETABLES #2 [0000006000 - 0000008000] TRAMPOLINE #3 [0001000000 - 0002695878] TEXT DATA BSS #4 [00026b6000 - 000f7d7600] RAMDISK #5 [000f7d8000 - 0010f42000] XEN START INFO #6 [0002696000 - 0002696149] BRK #7 [0000100000 - 0000670000] PGTABLE #8 [0010fcf000 - 0011f40000] PGTABLE #9 [0000010000 - 0000016840] MEMNODEMAP found SMP MP-table at [ffff8800000ff780] ff780 Zone PFN ranges: DMA 0x00000010 -> 0x00001000 DMA32 0x00001000 -> 0x00100000 Normal 0x00100000 -> 0x002ed0cf Movable zone start PFN for each node early_node_map[4] active PFN ranges 0: 0x00000010 -> 0x0000009a 0: 0x00000100 -> 0x000bf760 0: 0x00100000 -> 0x001c0000 2: 0x001c0000 -> 0x002ed0cf On node 0 totalpages: 1570538 DMA zone: 104 pages used for memmap DMA zone: 1401 pages reserved DMA zone: 2473 pages, LIFO batch:0 DMA32 zone: 26520 pages used for memmap DMA32 zone: 753608 pages, LIFO batch:31 Normal zone: 19968 pages used for memmap Normal zone: 766464 pages, LIFO batch:31 On node 2 totalpages: 1233103 Normal zone: 31310 pages used for memmap Normal zone: 1201793 pages, LIFO batch:31 ACPI: PM-Timer IO Port: 0x808 ACPI: Local APIC address 0xfee00000 ACPI: LAPIC (acpi_id[0x01] lapic_id[0x00] enabled) ACPI: LAPIC (acpi_id[0x02] lapic_id[0x10] enabled) ACPI: LAPIC (acpi_id[0x03] lapic_id[0x02] enabled) ACPI: LAPIC (acpi_id[0x04] lapic_id[0x12] enabled) ACPI: LAPIC (acpi_id[0x05] lapic_id[0x04] enabled) ACPI: LAPIC (acpi_id[0x06] lapic_id[0x14] enabled) ACPI: LAPIC (acpi_id[0x07] lapic_id[0x06] enabled) ACPI: LAPIC (acpi_id[0x08] lapic_id[0x16] enabled) ACPI: LAPIC (acpi_id[0x09] lapic_id[0x01] enabled) ACPI: LAPIC (acpi_id[0x0a] lapic_id[0x11] enabled) ACPI: LAPIC (acpi_id[0x0b] lapic_id[0x03] enabled) ACPI: LAPIC (acpi_id[0x0c] lapic_id[0x13] enabled) ACPI: LAPIC (acpi_id[0x0d] lapic_id[0x05] enabled) ACPI: LAPIC (acpi_id[0x0e] lapic_id[0x15] enabled) ACPI: LAPIC (acpi_id[0x0f] lapic_id[0x07] enabled) ACPI: LAPIC (acpi_id[0x10] lapic_id[0x17] enabled) ACPI: LAPIC_NMI (acpi_id[0xff] dfl dfl lint[0x1]) ACPI: IOAPIC (id[0x08] address[0xfec00000] gsi_base[0]) IOAPIC[0]: apic_id 8, version 0, address 0xfec00000, GSI 0-0 ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl) ERROR: Unable to locate IOAPIC for GSI 2 ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 20 low level) ERROR: Unable to locate IOAPIC for GSI 20 Using ACPI (MADT) for SMP configuration information ACPI: HPET id: 0xffffffff base: 0xfed00000 SMP: Allowing 16 CPUs, 0 hotplug CPUs nr_irqs_gsi: 256 PM: Registered nosave memory: 000000000009a000 - 0000000000100000 PM: Registered nosave memory: 00000000bf760000 - 00000000bf76e000 PM: Registered nosave memory: 00000000bf76e000 - 00000000bf770000 PM: Registered nosave memory: 00000000bf770000 - 00000000bf77e000 PM: Registered nosave memory: 00000000bf77e000 - 00000000bf7d0000 PM: Registered nosave memory: 00000000bf7d0000 - 00000000bf7e0000 PM: Registered nosave memory: 00000000bf7e0000 - 00000000bf7ec000 PM: Registered nosave memory: 00000000bf7ec000 - 00000000c0000000 PM: Registered nosave memory: 00000000c0000000 - 00000000fec00000 PM: Registered nosave memory: 00000000fec00000 - 00000000fec01000 PM: Registered nosave memory: 00000000fec01000 - 00000000fee00000 PM: Registered nosave memory: 00000000fee00000 - 00000000fee01000 PM: Registered nosave memory: 00000000fee01000 - 00000000ffc00000 PM: Registered nosave memory: 00000000ffc00000 - 0000000100000000 Allocating PCI resources starting at c0000000 (gap: c0000000:3ec00000) Booting paravirtualized kernel on Xen Xen version: 4.0.1-rc1 (preserve-AD) (dom0) NR_CPUS:512 nr_cpumask_bits:512 nr_cpu_ids:16 nr_node_ids:3 PERCPU: Embedded 478 pages/cpu @ffff880032052000 s1927128 r8192 d22568 u1957888 pcpu-alloc: s1927128 r8192 d22568 u1957888 alloc=478*4096 pcpu-alloc: [0] 00 [0] 02 [0] 04 [0] 06 [0] 08 [0] 10 [0] 12 [0] 14 pcpu-alloc: [1] 01 [1] 03 [1] 05 [1] 07 [1] 09 [1] 11 [1] 13 [1] 15 trying to map vcpu_info 0 at ffff88003205d020, mfn 15205d, offset 32 cpu 0 using vcpu_info at ffff88003205d020 trying to map vcpu_info 1 at ffff8801c7c58020, mfn 2e7c58, offset 32 cpu 1 using vcpu_info at ffff8801c7c58020 trying to map vcpu_info 2 at ffff88003223b020, mfn 15223b, offset 32 cpu 2 using vcpu_info at ffff88003223b020 trying to map vcpu_info 3 at ffff8801c7e36020, mfn 2e7e36, offset 32 cpu 3 using vcpu_info at ffff8801c7e36020 trying to map vcpu_info 4 at ffff880032419020, mfn 152419, offset 32 cpu 4 using vcpu_info at ffff880032419020 trying to map vcpu_info 5 at ffff8801c8014020, mfn 2e8014, offset 32 cpu 5 using vcpu_info at ffff8801c8014020 trying to map vcpu_info 6 at ffff8800325f7020, mfn 1525f7, offset 32 cpu 6 using vcpu_info at ffff8800325f7020 trying to map vcpu_info 7 at ffff8801c81f2020, mfn 2e81f2, offset 32 cpu 7 using vcpu_info at ffff8801c81f2020 trying to map vcpu_info 8 at ffff8800327d5020, mfn 1527d5, offset 32 cpu 8 using vcpu_info at ffff8800327d5020 trying to map vcpu_info 9 at ffff8801c83d0020, mfn 2e83d0, offset 32 cpu 9 using vcpu_info at ffff8801c83d0020 trying to map vcpu_info 10 at ffff8800329b3020, mfn 1529b3, offset 32 cpu 10 using vcpu_info at ffff8800329b3020 trying to map vcpu_info 11 at ffff8801c85ae020, mfn 2e85ae, offset 32 cpu 11 using vcpu_info at ffff8801c85ae020 trying to map vcpu_info 12 at ffff880032b91020, mfn 152b91, offset 32 cpu 12 using vcpu_info at ffff880032b91020 trying to map vcpu_info 13 at ffff8801c878c020, mfn 2e878c, offset 32 cpu 13 using vcpu_info at ffff8801c878c020 trying to map vcpu_info 14 at ffff880032d6f020, mfn 152d6f, offset 32 cpu 14 using vcpu_info at ffff880032d6f020 trying to map vcpu_info 15 at ffff8801c896a020, mfn 2e896a, offset 32 cpu 15 using vcpu_info at ffff8801c896a020 Xen: using vcpu_info placement Built 2 zonelists in Zone order, mobility grouping on. Total pages: 2724338 Policy zone: Normal Kernel command line: root=/dev/mapper/MISC-fedora ro nomodeset console=hvc0 earlyprintk=xen debug initcall_debug loglvel=10 PID hash table entries: 4096 (order: 3, 32768 bytes) Initializing CPU#0 DMA: Placing 64MB software IO TLB between ffff880020000000 - ffff880024000000 DMA: software IO TLB at phys 0x20000000 - 0x24000000 xen_swiotlb_fixup: buf=ffff880020000000 size=67108864 xen_swiotlb_fixup: buf=ffff880024060000 size=32768 Memory: 10546768k/12272444k available (4727k kernel code, 1057880k absent, 667796k reserved, 3359k data, 3380k init) SLUB: Genslabs=14, HWalign=64, Order=0-3, MinObjects=0, CPUs=16, Nodes=3 Hierarchical RCU implementation. NR_IRQS:4352 nr_irqs:4352 xen: --> irq=0 xen: --> irq=1 xen: --> irq=2 xen: --> irq=3 xen: --> irq=4 xen: --> irq=5 xen: --> irq=6 xen: --> irq=7 xen: --> irq=8 xen: --> irq=9 xen: --> irq=10 xen: --> irq=11 xen: --> irq=12 xen: --> irq=13 xen: --> irq=14 xen: --> irq=15 ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl) ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 20 low level) xen: sci override: source_irq=9 global_irq=20 trigger=c polarity=3 xen: registering gsi 20 triggering 0 polarity 1 alloc irq_desc for 20 on node 0 alloc kstat_irqs on node 0 xen: --> irq=20 xen: acpi sci 20 Console: colour VGA+ 80x25 console [hvc0] enabled, bootconsole disabled console [hvc0] enabled, bootconsole disabled Lock dependency validator: Copyright (c) 2006 Red Hat, Inc., Ingo Molnar ... MAX_LOCKDEP_SUBCLASSES: 8 ... MAX_LOCK_DEPTH: 48 ... MAX_LOCKDEP_KEYS: 8191 ... CLASSHASH_SIZE: 4096 ... MAX_LOCKDEP_ENTRIES: 16384 ... MAX_LOCKDEP_CHAINS: 32768 ... CHAINHASH_SIZE: 16384 memory used by lock dependency info: 6367 kB per task-struct memory footprint: 2688 bytes allocated 112721920 bytes of page_cgroup please try 'cgroup_disable=memory' option if you don't want memory cgroups ODEBUG: 24 of 24 active objects replaced Xen: using vcpuop timer interface installing Xen timer for CPU 0 alloc irq_desc for 4351 on node 0 alloc kstat_irqs on node 0 Detected 2266.784 MHz processor. Calibrating delay loop (skipped), value calculated using timer frequency.. 4533.56 BogoMIPS (lpj=2266784) Security Framework initialized SELinux: Initializing. SELinux: Starting in permissive mode Dentry cache hash table entries: 2097152 (order: 12, 16777216 bytes) Inode-cache hash table entries: 1048576 (order: 11, 8388608 bytes) Mount-cache hash table entries: 256 Initializing cgroup subsys ns Initializing cgroup subsys cpuacct Initializing cgroup subsys memory Initializing cgroup subsys devices Initializing cgroup subsys freezer Initializing cgroup subsys net_cls CPU: L1 I cache: 32K, L1 D cache: 32K CPU: L2 cache: 256K CPU: L3 cache: 8192K CPU 0/0x0 -> Node 0 CPU: Physical Processor ID: 0 CPU: Processor Core ID: 0 mce: CPU supports 9 MCE banks Performance Events: unsupported p6 CPU model 26 no PMU driver, software events only. lockdep: fixing up alternatives. SMP alternatives: switching to UP code ACPI: Core revision 20090903 ftrace: converting mcount calls to 0f 1f 44 00 00 ftrace: allocating 22950 entries in 91 pages alloc irq_desc for 4350 on node 0 alloc kstat_irqs on node 0 alloc irq_desc for 4349 on node 0 alloc kstat_irqs on node 0 alloc irq_desc for 4348 on node 0 alloc kstat_irqs on node 0 alloc irq_desc for 4347 on node 0 alloc kstat_irqs on node 0 calling migration_init+0x0/0x59 @ 1 initcall migration_init+0x0/0x59 returned 0 after 976 usecs calling spawn_ksoftirqd+0x0/0x5a @ 1 initcall spawn_ksoftirqd+0x0/0x5a returned 0 after 976 usecs calling init_call_single_data+0x0/0xad @ 1 initcall init_call_single_data+0x0/0xad returned 0 after 0 usecs calling spawn_softlockup_task+0x0/0x75 @ 1 initcall spawn_softlockup_task+0x0/0x75 returned 0 after 976 usecs calling relay_init+0x0/0x14 @ 1 initcall relay_init+0x0/0x14 returned 0 after 0 usecs calling tracer_alloc_buffers+0x0/0x218 @ 1 initcall tracer_alloc_buffers+0x0/0x218 returned 0 after 976 usecs calling init_trace_printk+0x0/0x12 @ 1 initcall init_trace_printk+0x0/0x12 returned 0 after 0 usecs calling trace_workqueue_early_init+0x0/0x137 @ 1 initcall trace_workqueue_early_init+0x0/0x137 returned 0 after 976 usecs calling mce_amd_init+0x0/0x33 @ 1 initcall mce_amd_init+0x0/0x33 returned 0 after 0 usecs installing Xen timer for CPU 1 alloc irq_desc for 4346 on node 0 alloc kstat_irqs on node 0 lockdep: fixing up alternatives. SMP alternatives: switching to SMP code alloc irq_desc for 4345 on node 0 alloc kstat_irqs on node 0 alloc irq_desc for 4344 on node 0 alloc kstat_irqs on node 0 alloc irq_desc for 4343 on node 0 alloc kstat_irqs on node 0 alloc irq_desc for 4342 on node 0 alloc kstat_irqs on node 0 Initializing CPU#1 CPU: L1 I cache: 32K, L1 D cache: 32K CPU: L2 cache: 256K CPU: L3 cache: 8192K CPU 1/0x0 -> Node 0 CPU: Physical Processor ID: 1 CPU: Processor Core ID: 0 installing Xen timer for CPU 2 alloc irq_desc for 4341 on node 0 alloc kstat_irqs on node 0 alloc irq_desc for 4340 on node 0 alloc kstat_irqs on node 0 alloc irq_desc for 4339 on node 0 alloc kstat_irqs on node 0 alloc irq_desc for 4338 on node 0 alloc kstat_irqs on node 0 alloc irq_desc for 4337 on node 0 alloc kstat_irqs on node 0 Initializing CPU#2 CPU: L1 I cache: 32K, L1 D cache: 32K CPU: L2 cache: 256K CPU: L3 cache: 8192K CPU 2/0x0 -> Node 0 CPU: Physical Processor ID: 0 CPU: Processor Core ID: 1 installing Xen timer for CPU 3 alloc irq_desc for 4336 on node 0 alloc kstat_irqs on node 0 alloc irq_desc for 4335 on node 0 alloc kstat_irqs on node 0 alloc irq_desc for 4334 on node 0 alloc kstat_irqs on node 0 alloc irq_desc for 4333 on node 0 alloc kstat_irqs on node 0 alloc irq_desc for 4332 on node 0 alloc kstat_irqs on node 0 Initializing CPU#3 CPU: L1 I cache: 32K, L1 D cache: 32K CPU: L2 cache: 256K CPU: L3 cache: 8192K CPU 3/0x0 -> Node 0 CPU: Physical Processor ID: 1 CPU: Processor Core ID: 1 installing Xen timer for CPU 4 alloc irq_desc for 4331 on node 0 alloc kstat_irqs on node 0 alloc irq_desc for 4330 on node 0 alloc kstat_irqs on node 0 alloc irq_desc for 4329 on node 0 alloc kstat_irqs on node 0 alloc irq_desc for 4328 on node 0 alloc kstat_irqs on node 0 alloc irq_desc for 4327 on node 0 alloc kstat_irqs on node 0 Initializing CPU#4 CPU: L1 I cache: 32K, L1 D cache: 32K CPU: L2 cache: 256K CPU: L3 cache: 8192K CPU 4/0x0 -> Node 0 CPU: Physical Processor ID: 0 CPU: Processor Core ID: 2 installing Xen timer for CPU 5 alloc irq_desc for 4326 on node 0 alloc kstat_irqs on node 0 alloc irq_desc for 4325 on node 0 alloc kstat_irqs on node 0 alloc irq_desc for 4324 on node 0 alloc kstat_irqs on node 0 alloc irq_desc for 4323 on node 0 alloc kstat_irqs on node 0 alloc irq_desc for 4322 on node 0 alloc kstat_irqs on node 0 Initializing CPU#5 CPU: L1 I cache: 32K, L1 D cache: 32K CPU: L2 cache: 256K CPU: L3 cache: 8192K CPU 5/0x0 -> Node 0 CPU: Physical Processor ID: 1 CPU: Processor Core ID: 2 installing Xen timer for CPU 6 alloc irq_desc for 4321 on node 0 alloc kstat_irqs on node 0 alloc irq_desc for 4320 on node 0 alloc kstat_irqs on node 0 alloc irq_desc for 4319 on node 0 alloc kstat_irqs on node 0 alloc irq_desc for 4318 on node 0 alloc kstat_irqs on node 0 alloc irq_desc for 4317 on node 0 alloc kstat_irqs on node 0 Initializing CPU#6 CPU: L1 I cache: 32K, L1 D cache: 32K CPU: L2 cache: 256K CPU: L3 cache: 8192K CPU 6/0x0 -> Node 0 CPU: Physical Processor ID: 0 CPU: Processor Core ID: 3 installing Xen timer for CPU 7 alloc irq_desc for 4316 on node 0 alloc kstat_irqs on node 0 alloc irq_desc for 4315 on node 0 alloc kstat_irqs on node 0 alloc irq_desc for 4314 on node 0 alloc kstat_irqs on node 0 alloc irq_desc for 4313 on node 0 alloc kstat_irqs on node 0 alloc irq_desc for 4312 on node 0 alloc kstat_irqs on node 0 Initializing CPU#7 CPU: L1 I cache: 32K, L1 D cache: 32K CPU: L2 cache: 256K CPU: L3 cache: 8192K CPU 7/0x0 -> Node 0 CPU: Physical Processor ID: 1 CPU: Processor Core ID: 3 installing Xen timer for CPU 8 alloc irq_desc for 4311 on node 0 alloc kstat_irqs on node 0 alloc irq_desc for 4310 on node 0 alloc kstat_irqs on node 0 alloc irq_desc for 4309 on node 0 alloc kstat_irqs on node 0 alloc irq_desc for 4308 on node 0 alloc kstat_irqs on node 0 alloc irq_desc for 4307 on node 0 alloc kstat_irqs on node 0 Initializing CPU#8 CPU: L1 I cache: 32K, L1 D cache: 32K CPU: L2 cache: 256K CPU: L3 cache: 8192K CPU 8/0x0 -> Node 0 CPU: Physical Processor ID: 0 CPU: Processor Core ID: 0 installing Xen timer for CPU 9 alloc irq_desc for 4306 on node 0 alloc kstat_irqs on node 0 alloc irq_desc for 4305 on node 0 alloc kstat_irqs on node 0 alloc irq_desc for 4304 on node 0 alloc kstat_irqs on node 0 alloc irq_desc for 4303 on node 0 alloc kstat_irqs on node 0 alloc irq_desc for 4302 on node 0 alloc kstat_irqs on node 0 Initializing CPU#9 CPU: L1 I cache: 32K, L1 D cache: 32K CPU: L2 cache: 256K CPU: L3 cache: 8192K CPU 9/0x0 -> Node 0 CPU: Physical Processor ID: 1 CPU: Processor Core ID: 0 installing Xen timer for CPU 10 alloc irq_desc for 4301 on node 0 alloc kstat_irqs on node 0 alloc irq_desc for 4300 on node 0 alloc kstat_irqs on node 0 alloc irq_desc for 4299 on node 0 alloc kstat_irqs on node 0 alloc irq_desc for 4298 on node 0 alloc kstat_irqs on node 0 alloc irq_desc for 4297 on node 0 alloc kstat_irqs on node 0 Initializing CPU#10 CPU: L1 I cache: 32K, L1 D cache: 32K CPU: L2 cache: 256K CPU: L3 cache: 8192K CPU 10/0x0 -> Node 0 CPU: Physical Processor ID: 0 CPU: Processor Core ID: 1 installing Xen timer for CPU 11 alloc irq_desc for 4296 on node 0 alloc kstat_irqs on node 0 alloc irq_desc for 4295 on node 0 alloc kstat_irqs on node 0 alloc irq_desc for 4294 on node 0 alloc kstat_irqs on node 0 alloc irq_desc for 4293 on node 0 alloc kstat_irqs on node 0 alloc irq_desc for 4292 on node 0 alloc kstat_irqs on node 0 Initializing CPU#11 CPU: L1 I cache: 32K, L1 D cache: 32K CPU: L2 cache: 256K CPU: L3 cache: 8192K CPU 11/0x0 -> Node 0 CPU: Physical Processor ID: 1 CPU: Processor Core ID: 1 installing Xen timer for CPU 12 alloc irq_desc for 4291 on node 0 alloc kstat_irqs on node 0 alloc irq_desc for 4290 on node 0 alloc kstat_irqs on node 0 alloc irq_desc for 4289 on node 0 alloc kstat_irqs on node 0 alloc irq_desc for 4288 on node 0 alloc kstat_irqs on node 0 alloc irq_desc for 4287 on node 0 alloc kstat_irqs on node 0 Initializing CPU#12 CPU: L1 I cache: 32K, L1 D cache: 32K CPU: L2 cache: 256K CPU: L3 cache: 8192K CPU 12/0x0 -> Node 0 CPU: Physical Processor ID: 0 CPU: Processor Core ID: 2 installing Xen timer for CPU 13 alloc irq_desc for 4286 on node 0 alloc kstat_irqs on node 0 alloc irq_desc for 4285 on node 0 alloc kstat_irqs on node 0 alloc irq_desc for 4284 on node 0 alloc kstat_irqs on node 0 alloc irq_desc for 4283 on node 0 alloc kstat_irqs on node 0 alloc irq_desc for 4282 on node 0 alloc kstat_irqs on node 0 Initializing CPU#13 CPU: L1 I cache: 32K, L1 D cache: 32K CPU: L2 cache: 256K CPU: L3 cache: 8192K CPU 13/0x0 -> Node 0 CPU: Physical Processor ID: 1 CPU: Processor Core ID: 2 installing Xen timer for CPU 14 alloc irq_desc for 4281 on node 0 alloc kstat_irqs on node 0 alloc irq_desc for 4280 on node 0 alloc kstat_irqs on node 0 alloc irq_desc for 4279 on node 0 alloc kstat_irqs on node 0 alloc irq_desc for 4278 on node 0 alloc kstat_irqs on node 0 alloc irq_desc for 4277 on node 0 alloc kstat_irqs on node 0 Initializing CPU#14 CPU: L1 I cache: 32K, L1 D cache: 32K CPU: L2 cache: 256K CPU: L3 cache: 8192K CPU 14/0x0 -> Node 0 CPU: Physical Processor ID: 0 CPU: Processor Core ID: 3 installing Xen timer for CPU 15 alloc irq_desc for 4276 on node 0 alloc kstat_irqs on node 0 alloc irq_desc for 4275 on node 0 alloc kstat_irqs on node 0 alloc irq_desc for 4274 on node 0 alloc kstat_irqs on node 0 alloc irq_desc for 4273 on node 0 alloc kstat_irqs on node 0 alloc irq_desc for 4272 on node 0 alloc kstat_irqs on node 0 Initializing CPU#15 CPU: L1 I cache: 32K, L1 D cache: 32K CPU: L2 cache: 256K CPU: L3 cache: 8192K CPU 15/0x0 -> Node 0 CPU: Physical Processor ID: 1 CPU: Processor Core ID: 3 Brought up 16 CPUs CPU0 attaching sched-domain: domain 0: span 0,8 level SIBLING groups: 0 (cpu_power = 589) 8 (cpu_power = 589) domain 1: span 0,8 level MC groups: 0,8 (cpu_power = 1178) domain 2: span 0-15 level CPU groups: 0,8 (cpu_power = 1178) 1,9 (cpu_power = 1178) 2,10 (cpu_power = 1178) 3,11 (cpu_power = 1178) 4,12 (cpu_power = 1178) 5,13 (cpu_power = 1178) 6,14 (cpu_power = 1178) 7,15 (cpu_power = 1178) domain 3: span 0-15 level NODE groups: 0-15 (cpu_power = 9424) CPU1 attaching sched-domain: domain 0: span 1,9 level SIBLING groups: 1 (cpu_power = 589) 9 (cpu_power = 589) domain 1: span 1,9 level MC groups: 1,9 (cpu_power = 1178) domain 2: span 0-15 level CPU groups: 1,9 (cpu_power = 1178) 2,10 (cpu_power = 1178) 3,11 (cpu_power = 1178) 4,12 (cpu_power = 1178) 5,13 (cpu_power = 1178) 6,14 (cpu_power = 1178) 7,15 (cpu_power = 1178) 0,8 (cpu_power = 1178) domain 3: span 0-15 level NODE groups: 0-15 (cpu_power = 9424) CPU2 attaching sched-domain: domain 0: span 2,10 level SIBLING groups: 2 (cpu_power = 589) 10 (cpu_power = 589) domain 1: span 2,10 level MC groups: 2,10 (cpu_power = 1178) domain 2: span 0-15 level CPU groups: 2,10 (cpu_power = 1178) 3,11 (cpu_power = 1178) 4,12 (cpu_power = 1178) 5,13 (cpu_power = 1178) 6,14 (cpu_power = 1178) 7,15 (cpu_power = 1178) 0,8 (cpu_power = 1178) 1,9 (cpu_power = 1178) domain 3: span 0-15 level NODE groups: 0-15 (cpu_power = 9424) CPU3 attaching sched-domain: domain 0: span 3,11 level SIBLING groups: 3 (cpu_power = 589) 11 (cpu_power = 589) domain 1: span 3,11 level MC groups: 3,11 (cpu_power = 1178) domain 2: span 0-15 level CPU groups: 3,11 (cpu_power = 1178) 4,12 (cpu_power = 1178) 5,13 (cpu_power = 1178) 6,14 (cpu_power = 1178) 7,15 (cpu_power = 1178) 0,8 (cpu_power = 1178) 1,9 (cpu_power = 1178) 2,10 (cpu_power = 1178) domain 3: span 0-15 level NODE groups: 0-15 (cpu_power = 9424) CPU4 attaching sched-domain: domain 0: span 4,12 level SIBLING groups: 4 (cpu_power = 589) 12 (cpu_power = 589) domain 1: span 4,12 level MC groups: 4,12 (cpu_power = 1178) domain 2: span 0-15 level CPU groups: 4,12 (cpu_power = 1178) 5,13 (cpu_power = 1178) 6,14 (cpu_power = 1178) 7,15 (cpu_power = 1178) 0,8 (cpu_power = 1178) 1,9 (cpu_power = 1178) 2,10 (cpu_power = 1178) 3,11 (cpu_power = 1178) domain 3: span 0-15 level NODE groups: 0-15 (cpu_power = 9424) CPU5 attaching sched-domain: domain 0: span 5,13 level SIBLING groups: 5 (cpu_power = 589) 13 (cpu_power = 589) domain 1: span 5,13 level MC groups: 5,13 (cpu_power = 1178) domain 2: span 0-15 level CPU groups: 5,13 (cpu_power = 1178) 6,14 (cpu_power = 1178) 7,15 (cpu_power = 1178) 0,8 (cpu_power = 1178) 1,9 (cpu_power = 1178) 2,10 (cpu_power = 1178) 3,11 (cpu_power = 1178) 4,12 (cpu_power = 1178) domain 3: span 0-15 level NODE groups: 0-15 (cpu_power = 9424) CPU6 attaching sched-domain: domain 0: span 6,14 level SIBLING groups: 6 (cpu_power = 589) 14 (cpu_power = 589) domain 1: span 6,14 level MC groups: 6,14 (cpu_power = 1178) domain 2: span 0-15 level CPU groups: 6,14 (cpu_power = 1178) 7,15 (cpu_power = 1178) 0,8 (cpu_power = 1178) 1,9 (cpu_power = 1178) 2,10 (cpu_power = 1178) 3,11 (cpu_power = 1178) 4,12 (cpu_power = 1178) 5,13 (cpu_power = 1178) domain 3: span 0-15 level NODE groups: 0-15 (cpu_power = 9424) CPU7 attaching sched-domain: domain 0: span 7,15 level SIBLING groups: 7 (cpu_power = 589) 15 (cpu_power = 589) domain 1: span 7,15 level MC groups: 7,15 (cpu_power = 1178) domain 2: span 0-15 level CPU groups: 7,15 (cpu_power = 1178) 0,8 (cpu_power = 1178) 1,9 (cpu_power = 1178) 2,10 (cpu_power = 1178) 3,11 (cpu_power = 1178) 4,12 (cpu_power = 1178) 5,13 (cpu_power = 1178) 6,14 (cpu_power = 1178) domain 3: span 0-15 level NODE groups: 0-15 (cpu_power = 9424) CPU8 attaching sched-domain: domain 0: span 0,8 level SIBLING groups: 8 (cpu_power = 589) 0 (cpu_power = 589) domain 1: span 0,8 level MC groups: 0,8 (cpu_power = 1178) domain 2: span 0-15 level CPU groups: 0,8 (cpu_power = 1178) 1,9 (cpu_power = 1178) 2,10 (cpu_power = 1178) 3,11 (cpu_power = 1178) 4,12 (cpu_power = 1178) 5,13 (cpu_power = 1178) 6,14 (cpu_power = 1178) 7,15 (cpu_power = 1178) domain 3: span 0-15 level NODE groups: 0-15 (cpu_power = 9424) CPU9 attaching sched-domain: domain 0: span 1,9 level SIBLING groups: 9 (cpu_power = 589) 1 (cpu_power = 589) domain 1: span 1,9 level MC groups: 1,9 (cpu_power = 1178) domain 2: span 0-15 level CPU groups: 1,9 (cpu_power = 1178) 2,10 (cpu_power = 1178) 3,11 (cpu_power = 1178) 4,12 (cpu_power = 1178) 5,13 (cpu_power = 1178) 6,14 (cpu_power = 1178) 7,15 (cpu_power = 1178) 0,8 (cpu_power = 1178) domain 3: span 0-15 level NODE groups: 0-15 (cpu_power = 9424) CPU10 attaching sched-domain: domain 0: span 2,10 level SIBLING groups: 10 (cpu_power = 589) 2 (cpu_power = 589) domain 1: span 2,10 level MC groups: 2,10 (cpu_power = 1178) domain 2: span 0-15 level CPU groups: 2,10 (cpu_power = 1178) 3,11 (cpu_power = 1178) 4,12 (cpu_power = 1178) 5,13 (cpu_power = 1178) 6,14 (cpu_power = 1178) 7,15 (cpu_power = 1178) 0,8 (cpu_power = 1178) 1,9 (cpu_power = 1178) domain 3: span 0-15 level NODE groups: 0-15 (cpu_power = 9424) CPU11 attaching sched-domain: domain 0: span 3,11 level SIBLING groups: 11 (cpu_power = 589) 3 (cpu_power = 589) domain 1: span 3,11 level MC groups: 3,11 (cpu_power = 1178) domain 2: span 0-15 level CPU groups: 3,11 (cpu_power = 1178) 4,12 (cpu_power = 1178) 5,13 (cpu_power = 1178) 6,14 (cpu_power = 1178) 7,15 (cpu_power = 1178) 0,8 (cpu_power = 1178) 1,9 (cpu_power = 1178) 2,10 (cpu_power = 1178) domain 3: span 0-15 level NODE groups: 0-15 (cpu_power = 9424) CPU12 attaching sched-domain: domain 0: span 4,12 level SIBLING groups: 12 (cpu_power = 589) 4 (cpu_power = 589) domain 1: span 4,12 level MC groups: 4,12 (cpu_power = 1178) domain 2: span 0-15 level CPU groups: 4,12 (cpu_power = 1178) 5,13 (cpu_power = 1178) 6,14 (cpu_power = 1178) 7,15 (cpu_power = 1178) 0,8 (cpu_power = 1178) 1,9 (cpu_power = 1178) 2,10 (cpu_power = 1178) 3,11 (cpu_power = 1178) domain 3: span 0-15 level NODE groups: 0-15 (cpu_power = 9424) CPU13 attaching sched-domain: domain 0: span 5,13 level SIBLING groups: 13 (cpu_power = 589) 5 (cpu_power = 589) domain 1: span 5,13 level MC groups: 5,13 (cpu_power = 1178) domain 2: span 0-15 level CPU groups: 5,13 (cpu_power = 1178) 6,14 (cpu_power = 1178) 7,15 (cpu_power = 1178) 0,8 (cpu_power = 1178) 1,9 (cpu_power = 1178) 2,10 (cpu_power = 1178) 3,11 (cpu_power = 1178) 4,12 (cpu_power = 1178) domain 3: span 0-15 level NODE groups: 0-15 (cpu_power = 9424) CPU14 attaching sched-domain: domain 0: span 6,14 level SIBLING groups: 14 (cpu_power = 589) 6 (cpu_power = 589) domain 1: span 6,14 level MC groups: 6,14 (cpu_power = 1178) domain 2: span 0-15 level CPU groups: 6,14 (cpu_power = 1178) 7,15 (cpu_power = 1178) 0,8 (cpu_power = 1178) 1,9 (cpu_power = 1178) 2,10 (cpu_power = 1178) 3,11 (cpu_power = 1178) 4,12 (cpu_power = 1178) 5,13 (cpu_power = 1178) domain 3: span 0-15 level NODE groups: 0-15 (cpu_power = 9424) CPU15 attaching sched-domain: domain 0: span 7,15 level SIBLING groups: 15 (cpu_power = 589) 7 (cpu_power = 589) domain 1: span 7,15 level MC groups: 7,15 (cpu_power = 1178) domain 2: span 0-15 level CPU groups: 7,15 (cpu_power = 1178) 0,8 (cpu_power = 1178) 1,9 (cpu_power = 1178) 2,10 (cpu_power = 1178) 3,11 (cpu_power = 1178) 4,12 (cpu_power = 1178) 5,13 (cpu_power = 1178) 6,14 (cpu_power = 1178) domain 3: span 0-15 level NODE groups: 0-15 (cpu_power = 9424) calling init_mmap_min_addr+0x0/0x26 @ 1 initcall init_mmap_min_addr+0x0/0x26 returned 0 after 0 usecs calling init_cpufreq_transition_notifier_list+0x0/0x1b @ 1 initcall init_cpufreq_transition_notifier_list+0x0/0x1b returned 0 after 0 usecs calling net_ns_init+0x0/0xf8 @ 1 initcall net_ns_init+0x0/0xf8 returned 0 after 976 usecs calling e820_mark_nvs_memory+0x0/0x40 @ 1 initcall e820_mark_nvs_memory+0x0/0x40 returned 0 after 976 usecs calling cpufreq_tsc+0x0/0x28 @ 1 initcall cpufreq_tsc+0x0/0x28 returned 0 after 0 usecs calling pci_reboot_init+0x0/0x14 @ 1 initcall pci_reboot_init+0x0/0x14 returned 0 after 0 usecs calling init_lapic_sysfs+0x0/0x2d @ 1 initcall init_lapic_sysfs+0x0/0x2d returned 0 after 0 usecs calling alloc_frozen_cpus+0x0/0xd @ 1 initcall alloc_frozen_cpus+0x0/0xd returned 0 after 0 usecs calling sysctl_init+0x0/0x32 @ 1 initcall sysctl_init+0x0/0x32 returned 0 after 976 usecs calling ksysfs_init+0x0/0xbb @ 1 initcall ksysfs_init+0x0/0xbb returned 0 after 0 usecs calling async_init+0x0/0x60 @ 1 initcall async_init+0x0/0x60 returned 0 after 976 usecs calling init_jiffies_clocksource+0x0/0x12 @ 1 initcall init_jiffies_clocksource+0x0/0x12 returned 0 after 0 usecs calling pm_init+0x0/0x34 @ 1 initcall pm_init+0x0/0x34 returned 0 after 0 usecs calling pm_disk_init+0x0/0x19 @ 1 initcall pm_disk_init+0x0/0x19 returned 0 after 0 usecs calling swsusp_header_init+0x0/0x31 @ 1 initcall swsusp_header_init+0x0/0x31 returned 0 after 0 usecs calling init_zero_pfn+0x0/0x35 @ 1 initcall init_zero_pfn+0x0/0x35 returned 0 after 0 usecs calling filelock_init+0x0/0x2e @ 1 initcall filelock_init+0x0/0x2e returned 0 after 976 usecs calling init_misc_binfmt+0x0/0x42 @ 1 initcall init_misc_binfmt+0x0/0x42 returned 0 after 0 usecs calling init_script_binfmt+0x0/0x14 @ 1 initcall init_script_binfmt+0x0/0x14 returned 0 after 0 usecs calling init_elf_binfmt+0x0/0x14 @ 1 initcall init_elf_binfmt+0x0/0x14 returned 0 after 0 usecs calling init_compat_elf_binfmt+0x0/0x14 @ 1 initcall init_compat_elf_binfmt+0x0/0x14 returned 0 after 0 usecs calling debugfs_init+0x0/0x5a @ 1 initcall debugfs_init+0x0/0x5a returned 0 after 0 usecs calling securityfs_init+0x0/0x51 @ 1 initcall securityfs_init+0x0/0x51 returned 0 after 0 usecs calling random32_init+0x0/0xd7 @ 1 initcall random32_init+0x0/0xd7 returned 0 after 0 usecs calling __gnttab_init+0x0/0x26 @ 1 Grant table initialized initcall __gnttab_init+0x0/0x26 returned 0 after 976 usecs calling regulator_init+0x0/0x2e @ 1 regulator: core version 0.5 initcall regulator_init+0x0/0x2e returned 0 after 0 usecs calling early_resume_init+0x0/0x19d @ 1 Time: 11:17:44 Date: 05/30/10 initcall early_resume_init+0x0/0x19d returned 0 after 0 usecs calling cpufreq_core_init+0x0/0xa2 @ 1 initcall cpufreq_core_init+0x0/0xa2 returned 0 after 0 usecs calling cpuidle_init+0x0/0x40 @ 1 initcall cpuidle_init+0x0/0x40 returned 0 after 976 usecs calling sock_init+0x0/0x5e @ 1 initcall sock_init+0x0/0x5e returned 0 after 976 usecs calling net_inuse_init+0x0/0x26 @ 1 initcall net_inuse_init+0x0/0x26 returned 0 after 0 usecs calling netpoll_init+0x0/0x41 @ 1 initcall netpoll_init+0x0/0x41 returned 0 after 0 usecs calling netlink_proto_init+0x0/0x142 @ 1 NET: Registered protocol family 16 initcall netlink_proto_init+0x0/0x142 returned 0 after 976 usecs calling bdi_class_init+0x0/0x41 @ 1 initcall bdi_class_init+0x0/0x41 returned 0 after 976 usecs calling kobject_uevent_init+0x0/0x54 @ 1 initcall kobject_uevent_init+0x0/0x54 returned 0 after 976 usecs calling pcibus_class_init+0x0/0x19 @ 1 initcall pcibus_class_init+0x0/0x19 returned 0 after 976 usecs calling pci_driver_init+0x0/0x12 @ 1 initcall pci_driver_init+0x0/0x12 returned 0 after 976 usecs calling backlight_class_init+0x0/0x5d @ 1 initcall backlight_class_init+0x0/0x5d returned 0 after 0 usecs calling __xenbus_probe_init+0x0/0x21 @ 1 alloc irq_desc for 4271 on node 0 alloc kstat_irqs on node 0 initcall __xenbus_probe_init+0x0/0x21 returned 0 after 1952 usecs calling tty_class_init+0x0/0x38 @ 1 initcall tty_class_init+0x0/0x38 returned 0 after 0 usecs calling vtconsole_class_init+0x0/0xc3 @ 1 initcall vtconsole_class_init+0x0/0xc3 returned 0 after 976 usecs calling register_node_type+0x0/0x7e @ 1 initcall register_node_type+0x0/0x7e returned 0 after 976 usecs calling amd_postcore_init+0x0/0x78 @ 1 initcall amd_postcore_init+0x0/0x78 returned 0 after 0 usecs calling arch_kdebugfs_init+0x0/0x272 @ 1 initcall arch_kdebugfs_init+0x0/0x272 returned 0 after 0 usecs calling mtrr_if_init+0x0/0x63 @ 1 initcall mtrr_if_init+0x0/0x63 returned 0 after 0 usecs calling ffh_cstate_init+0x0/0x2a @ 1 initcall ffh_cstate_init+0x0/0x2a returned 0 after 0 usecs calling arch_init_ftrace_syscalls+0x0/0x11e @ 1 initcall arch_init_ftrace_syscalls+0x0/0x11e returned 0 after 976 usecs calling acpi_pci_init+0x0/0x5c @ 1 ACPI: bus type pci registered initcall acpi_pci_init+0x0/0x5c returned 0 after 0 usecs calling register_xen_pci_notifier+0x0/0x24 @ 1 initcall register_xen_pci_notifier+0x0/0x24 returned 0 after 0 usecs calling setup_vcpu_hotplug_event+0x0/0x22 @ 1 initcall setup_vcpu_hotplug_event+0x0/0x22 returned 0 after 0 usecs calling dmi_id_init+0x0/0x34c @ 1 initcall dmi_id_init+0x0/0x34c returned 0 after 976 usecs calling dma_bus_init+0x0/0x3f @ 1 initcall dma_bus_init+0x0/0x3f returned 0 after 0 usecs calling dma_channel_table_init+0x0/0x10e @ 1 initcall dma_channel_table_init+0x0/0x10e returned 0 after 0 usecs calling pci_arch_init+0x0/0x60 @ 1 PCI: MCFG configuration 0: base e0000000 segment 0 buses 0 - 255 PCI: Not using MMCONFIG. PCI: Using configuration type 1 for base access initcall pci_arch_init+0x0/0x60 returned 0 after 0 usecs calling topology_init+0x0/0x97 @ 1 initcall topology_init+0x0/0x97 returned 0 after 976 usecs calling mtrr_init_finialize+0x0/0x3d @ 1 initcall mtrr_init_finialize+0x0/0x3d returned 0 after 0 usecs calling param_sysfs_init+0x0/0x23a @ 1 initcall param_sysfs_init+0x0/0x23a returned 0 after 7811 usecs calling pm_sysrq_init+0x0/0x1e @ 1 initcall pm_sysrq_init+0x0/0x1e returned 0 after 0 usecs calling audit_watch_init+0x0/0x2f @ 1 initcall audit_watch_init+0x0/0x2f returned 0 after 0 usecs calling init_slow_work+0x0/0x37 @ 1 initcall init_slow_work+0x0/0x37 returned 0 after 0 usecs calling default_bdi_init+0x0/0xc6 @ 1 initcall default_bdi_init+0x0/0xc6 returned 0 after 976 usecs calling init_bio+0x0/0xce @ 1 bio: create slab <bio-0> at 0 initcall init_bio+0x0/0xce returned 0 after 3905 usecs calling fsnotify_init+0x0/0x12 @ 1 initcall fsnotify_init+0x0/0x12 returned 0 after 0 usecs calling fsnotify_notification_init+0x0/0x100 @ 1 initcall fsnotify_notification_init+0x0/0x100 returned 0 after 976 usecs calling cryptomgr_init+0x0/0x12 @ 1 initcall cryptomgr_init+0x0/0x12 returned 0 after 0 usecs calling blk_settings_init+0x0/0x2a @ 1 initcall blk_settings_init+0x0/0x2a returned 0 after 0 usecs calling blk_ioc_init+0x0/0x2a @ 1 initcall blk_ioc_init+0x0/0x2a returned 0 after 0 usecs calling blk_softirq_init+0x0/0x70 @ 1 initcall blk_softirq_init+0x0/0x70 returned 0 after 0 usecs calling blk_iopoll_setup+0x0/0x70 @ 1 initcall blk_iopoll_setup+0x0/0x70 returned 0 after 0 usecs calling genhd_device_init+0x0/0x7b @ 1 initcall genhd_device_init+0x0/0x7b returned 0 after 2929 usecs calling blk_dev_integrity_init+0x0/0x2a @ 1 initcall blk_dev_integrity_init+0x0/0x2a returned 0 after 0 usecs calling pci_slot_init+0x0/0x4c @ 1 initcall pci_slot_init+0x0/0x4c returned 0 after 0 usecs calling fbmem_init+0x0/0x98 @ 1 initcall fbmem_init+0x0/0x98 returned 0 after 0 usecs calling acpi_init+0x0/0x2d1 @ 1 ERROR: Unable to locate IOAPIC for GSI 20 ACPI: EC: Look up EC in DSDT ACPI Warning for \_SB_._OSC: Return type mismatch - found Integer, expected Buffer (20090903/nspredef-1006) \_SB_:_OSC evaluation returned wrong type _OSC request data:1 6 ACPI: Executed 1 blocks of module-level executable AML code ACPI: Interpreter enabled ACPI: (supports S0 S1 S4 S5) ACPI: Using IOAPIC for interrupt routing PCI: MCFG configuration 0: base e0000000 segment 0 buses 0 - 255 PCI: MCFG area at e0000000 reserved in ACPI motherboard resources PCI: Using MMCONFIG at e0000000 - efffffff ACPI Warning: Incorrect checksum in table [OEMB] - 54, should be 51 (20090903/tbutils-314) ACPI Warning: Incorrect checksum in table [ ] - 50, should be 94 (20090903/tbutils-314) initcall acpi_init+0x0/0x2d1 returned 0 after 158183 usecs calling dock_init+0x0/0x8d @ 1 ACPI: No dock devices found. initcall dock_init+0x0/0x8d returned 0 after 0 usecs calling acpi_pci_root_init+0x0/0x28 @ 1 ACPI: PCI Root Bridge [PCI0] (0000:00) pci 0000:00:00.0: PME# supported from D0 D3hot D3cold pci 0000:00:00.0: PME# disabled pci 0000:00:01.0: PME# supported from D0 D3hot D3cold pci 0000:00:01.0: PME# disabled pci 0000:00:03.0: PME# supported from D0 D3hot D3cold pci 0000:00:03.0: PME# disabled pci 0000:00:07.0: PME# supported from D0 D3hot D3cold pci 0000:00:07.0: PME# disabled pci 0000:00:16.0: reg 10 64bit mmio: [0xfbbfc000-0xfbbfffff] pci 0000:00:16.1: reg 10 64bit mmio: [0xfbbf8000-0xfbbfbfff] pci 0000:00:16.2: reg 10 64bit mmio: [0xfbbf4000-0xfbbf7fff] pci 0000:00:16.3: reg 10 64bit mmio: [0xfbbf0000-0xfbbf3fff] pci 0000:00:16.4: reg 10 64bit mmio: [0xfbbec000-0xfbbeffff] pci 0000:00:16.5: reg 10 64bit mmio: [0xfbbe8000-0xfbbebfff] pci 0000:00:16.6: reg 10 64bit mmio: [0xfbbe4000-0xfbbe7fff] pci 0000:00:16.7: reg 10 64bit mmio: [0xfbbe0000-0xfbbe3fff] pci 0000:00:1a.0: reg 20 io port: [0xac00-0xac1f] pci 0000:00:1a.1: reg 20 io port: [0xa880-0xa89f] pci 0000:00:1a.2: reg 20 io port: [0xa800-0xa81f] pci 0000:00:1a.7: reg 10 32bit mmio: [0xfbbde000-0xfbbde3ff] pci 0000:00:1a.7: PME# supported from D0 D3hot D3cold pci 0000:00:1a.7: PME# disabled pci 0000:00:1b.0: reg 10 64bit mmio: [0xfbbd8000-0xfbbdbfff] pci 0000:00:1b.0: PME# supported from D0 D3hot D3cold pci 0000:00:1b.0: PME# disabled pci 0000:00:1c.0: PME# supported from D0 D3hot D3cold pci 0000:00:1c.0: PME# disabled pci 0000:00:1c.4: PME# supported from D0 D3hot D3cold pci 0000:00:1c.4: PME# disabled pci 0000:00:1c.5: PME# supported from D0 D3hot D3cold pci 0000:00:1c.5: PME# disabled pci 0000:00:1d.0: reg 20 io port: [0xa480-0xa49f] pci 0000:00:1d.1: reg 20 io port: [0xa400-0xa41f] pci 0000:00:1d.2: reg 20 io port: [0xa080-0xa09f] pci 0000:00:1d.7: reg 10 32bit mmio: [0xfbbdc000-0xfbbdc3ff] pci 0000:00:1d.7: PME# supported from D0 D3hot D3cold pci 0000:00:1d.7: PME# disabled pci 0000:00:1f.0: quirk: region 0800-087f claimed by ICH6 ACPI/GPIO/TCO pci 0000:00:1f.0: quirk: region 0500-053f claimed by ICH6 GPIO pci 0000:00:1f.0: ICH7 LPC Generic IO decode 1 PIO at 0a00 (mask 00ff) pci 0000:00:1f.0: ICH7 LPC Generic IO decode 3 PIO at 0290 (mask 0097) pci 0000:00:1f.2: reg 10 io port: [0xa000-0xa007] pci 0000:00:1f.2: reg 14 io port: [0x9c00-0x9c03] pci 0000:00:1f.2: reg 18 io port: [0x9880-0x9887] pci 0000:00:1f.2: reg 1c io port: [0x9800-0x9803] pci 0000:00:1f.2: reg 20 io port: [0x9480-0x949f] pci 0000:00:1f.2: reg 24 32bit mmio: [0xfbbd6000-0xfbbd67ff] pci 0000:00:1f.2: PME# supported from D3hot pci 0000:00:1f.2: PME# disabled pci 0000:00:1f.3: reg 10 64bit mmio: [0xfbbd4000-0xfbbd40ff] pci 0000:00:1f.3: reg 20 io port: [0x400-0x41f] pci 0000:01:00.0: reg 10 32bit mmio: [0xf6000000-0xf6ffffff] pci 0000:01:00.0: reg 14 64bit mmio pref: [0xc0000000-0xcfffffff] pci 0000:01:00.0: reg 1c 64bit mmio: [0xf4000000-0xf5ffffff] pci 0000:01:00.0: reg 24 io port: [0xbc00-0xbc7f] pci 0000:01:00.0: reg 30 32bit mmio pref: [0xf3fe0000-0xf3ffffff] pci 0000:00:01.0: bridge io port: [0xb000-0xbfff] pci 0000:00:01.0: bridge 32bit mmio: [0xf3f00000-0xf6ffffff] pci 0000:00:01.0: bridge 64bit mmio pref: [0xc0000000-0xcfffffff] pci 0000:03:00.0: reg 10 32bit mmio: [0xfa000000-0xfaffffff] pci 0000:03:00.0: reg 14 64bit mmio pref: [0xd0000000-0xdfffffff] pci 0000:03:00.0: reg 1c 64bit mmio: [0xf8000000-0xf9ffffff] pci 0000:03:00.0: reg 24 io port: [0xcc00-0xcc7f] pci 0000:03:00.0: reg 30 32bit mmio pref: [0xf7fe0000-0xf7ffffff] pci 0000:00:07.0: bridge io port: [0xc000-0xcfff] pci 0000:00:07.0: bridge 32bit mmio: [0xf7f00000-0xfaffffff] pci 0000:00:07.0: bridge 64bit mmio pref: [0xd0000000-0xdfffffff] pci 0000:04:00.0: PME# supported from D0 D3hot D3cold pci 0000:04:00.0: PME# disabled pci 0000:04:00.2: PME# supported from D0 D3hot D3cold pci 0000:04:00.2: PME# disabled pci 0000:04:00.0: disabling ASPM on pre-1.1 PCIe device. You can enable it with 'pcie_aspm=force' pci 0000:00:1c.0: bridge 32bit mmio: [0xfbc00000-0xfbcfffff] pci 0000:00:1c.0: bridge 64bit mmio pref: [0xf2f00000-0xf2ffffff] pci 0000:05:0e.0: reg 10 32bit mmio pref: [0xf2ff0000-0xf2ffffff] pci 0000:05:0e.0: reg 18 32bit mmio: [0xfbce0000-0xfbcfffff] pci 0000:05:0e.0: reg 30 32bit mmio pref: [0xfbcd0000-0xfbcd7fff] pci 0000:05:0e.0: supports D1 pci 0000:04:00.0: bridge 32bit mmio: [0xfbc00000-0xfbcfffff] pci 0000:04:00.0: bridge 64bit mmio pref: [0xf2f00000-0xf2ffffff] pci 0000:07:00.0: reg 10 32bit mmio: [0xfbde0000-0xfbdfffff] pci 0000:07:00.0: reg 18 io port: [0xdc00-0xdc1f] pci 0000:07:00.0: reg 1c 32bit mmio: [0xfbddc000-0xfbddffff] pci 0000:07:00.0: PME# supported from D0 D3hot D3cold pci 0000:07:00.0: PME# disabled pci 0000:00:1c.4: bridge io port: [0xd000-0xdfff] pci 0000:00:1c.4: bridge 32bit mmio: [0xfbd00000-0xfbdfffff] pci 0000:08:00.0: reg 10 32bit mmio: [0xfbee0000-0xfbefffff] pci 0000:08:00.0: reg 18 io port: [0xec00-0xec1f] pci 0000:08:00.0: reg 1c 32bit mmio: [0xfbedc000-0xfbedffff] pci 0000:08:00.0: PME# supported from D0 D3hot D3cold pci 0000:08:00.0: PME# disabled pci 0000:00:1c.5: bridge io port: [0xe000-0xefff] pci 0000:00:1c.5: bridge 32bit mmio: [0xfbe00000-0xfbefffff] pci 0000:00:1e.0: transparent bridge ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P0P1._PRT] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P0P4._PRT] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P0P8._PRT] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P0P9._PRT] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.NPE1._PRT] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.NPE3._PRT] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.NPE7._PRT] (XEN) PCI add device 00:00.0 (XEN) PCI add device 00:01.0 (XEN) PCI add device 00:03.0 (XEN) PCI add device 00:07.0 (XEN) PCI add device 00:14.0 (XEN) PCI add device 00:14.1 (XEN) PCI add device 00:14.2 (XEN) PCI add device 00:14.3 (XEN) PCI add device 00:16.0 (XEN) PCI add device 00:16.1 (XEN) PCI add device 00:16.2 (XEN) PCI add device 00:16.3 (XEN) PCI add device 00:16.4 (XEN) PCI add device 00:16.5 (XEN) PCI add device 00:16.6 (XEN) PCI add device 00:16.7 (XEN) PCI add device 00:1a.0 (XEN) PCI add device 00:1a.1 (XEN) PCI add device 00:1a.2 (XEN) PCI add device 00:1a.7 (XEN) PCI add device 00:1b.0 (XEN) PCI add device 00:1c.0 (XEN) PCI add device 00:1c.4 (XEN) PCI add device 00:1c.5 (XEN) PCI add device 00:1d.0 (XEN) PCI add device 00:1d.1 (XEN) PCI add device 00:1d.2 (XEN) PCI add device 00:1d.7 (XEN) PCI add device 00:1e.0 (XEN) PCI add device 00:1f.0 (XEN) PCI add device 00:1f.2 (XEN) PCI add device 00:1f.3 (XEN) PCI add device 01:00.0 (XEN) PCI add device 03:00.0 (XEN) PCI add device 04:00.0 (XEN) PCI add device 04:00.2 (XEN) PCI add device 05:0e.0 (XEN) PCI add device 07:00.0 (XEN) PCI add device 08:00.0 initcall acpi_pci_root_init+0x0/0x28 returned 0 after 89843 usecs calling acpi_pci_link_init+0x0/0x43 @ 1 ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 6 7 10 *11 12 14 15) ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 6 7 *10 11 12 14 15) ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 6 7 10 11 12 *14 15) ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 6 7 10 11 12 14 *15) ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 6 7 10 11 12 14 15) *0, disabled. ACPI: PCI Interrupt Link [LNKF] (IRQs 3 4 6 *7 10 11 12 14 15) ACPI: PCI Interrupt Link [LNKG] (IRQs 3 4 *6 7 10 11 12 14 15) ACPI: PCI Interrupt Link [LNKH] (IRQs 3 4 6 7 *10 11 12 14 15) initcall acpi_pci_link_init+0x0/0x43 returned 0 after 4882 usecs calling pnp_init+0x0/0x12 @ 1 initcall pnp_init+0x0/0x12 returned 0 after 0 usecs calling __setup_shutdown_event+0x0/0x2a @ 1 initcall __setup_shutdown_event+0x0/0x2a returned 0 after 0 usecs calling xen_pcpu_init+0x0/0xa7 @ 1 sync cpu 0 get result 1 max_id f sync cpu 1 get result 1 max_id f sync cpu 2 get result 1 max_id f sync cpu 3 get result 1 max_id f sync cpu 4 get result 1 max_id f sync cpu 5 get result 1 max_id f sync cpu 6 get result 1 max_id f sync cpu 7 get result 1 max_id f sync cpu 8 get result 1 max_id f sync cpu 9 get result 1 max_id f sync cpu a get result 1 max_id f sync cpu b get result 1 max_id f sync cpu c get result 1 max_id f sync cpu d get result 1 max_id f sync cpu e get result 1 max_id f sync cpu f get result 1 max_id f alloc irq_desc for 4270 on node 0 alloc kstat_irqs on node 0 initcall xen_pcpu_init+0x0/0xa7 returned 4270 after 16601 usecs initcall xen_pcpu_init+0x0/0xa7 returned with error code 4270 calling xenbus_probe_backend_init+0x0/0x64 @ 1 initcall xenbus_probe_backend_init+0x0/0x64 returned 0 after 976 usecs calling xenbus_probe_frontend_init+0x0/0x64 @ 1 initcall xenbus_probe_frontend_init+0x0/0x64 returned 0 after 0 usecs calling balloon_init+0x0/0x208 @ 1 xen_balloon: Initialising balloon driver with page order 0. initcall balloon_init+0x0/0x208 returned 0 after 0 usecs calling xen_acpi_processor_extcntl_init+0x0/0x4f @ 1 initcall xen_acpi_processor_extcntl_init+0x0/0x4f returned 0 after 0 usecs calling misc_init+0x0/0xb7 @ 1 initcall misc_init+0x0/0xb7 returned 0 after 0 usecs calling vga_arb_device_init+0x0/0x78 @ 1 vgaarb: device added: PCI:0000:01:00.0,decodes=io +mem,owns=none,locks=none vgaarb: device added: PCI:0000:03:00.0,decodes=io+mem,owns=io +mem,locks=none vgaarb: loaded initcall vga_arb_device_init+0x0/0x78 returned 0 after 976 usecs calling cn_init+0x0/0xa3 @ 1 initcall cn_init+0x0/0xa3 returned 0 after 976 usecs calling init_scsi+0x0/0x91 @ 1 SCSI subsystem initialized initcall init_scsi+0x0/0x91 returned 0 after 976 usecs calling ata_init+0x0/0x390 @ 1 libata version 3.00 loaded. initcall ata_init+0x0/0x390 returned 0 after 1953 usecs calling phy_init+0x0/0x31 @ 1 initcall phy_init+0x0/0x31 returned 0 after 976 usecs calling init_pcmcia_cs+0x0/0x36 @ 1 initcall init_pcmcia_cs+0x0/0x36 returned 0 after 0 usecs calling usb_init+0x0/0x1b2 @ 1 usbcore: registered new interface driver usbfs usbcore: registered new interface driver hub usbcore: registered new device driver usb initcall usb_init+0x0/0x1b2 returned 0 after 1953 usecs calling serio_init+0x0/0x89 @ 1 initcall serio_init+0x0/0x89 returned 0 after 976 usecs calling input_init+0x0/0x13d @ 1 initcall input_init+0x0/0x13d returned 0 after 0 usecs calling rtc_init+0x0/0x71 @ 1 initcall rtc_init+0x0/0x71 returned 0 after 976 usecs calling power_supply_class_init+0x0/0x38 @ 1 initcall power_supply_class_init+0x0/0x38 returned 0 after 0 usecs calling thermal_init+0x0/0x58 @ 1 initcall thermal_init+0x0/0x58 returned 0 after 0 usecs calling md_init+0x0/0xd0 @ 1 initcall md_init+0x0/0xd0 returned 0 after 0 usecs calling leds_init+0x0/0x40 @ 1 initcall leds_init+0x0/0x40 returned 0 after 0 usecs calling pci_subsys_init+0x0/0x11a @ 1 PCI: Using ACPI for IRQ routing initcall pci_subsys_init+0x0/0x11a returned 0 after 0 usecs calling proto_init+0x0/0x12 @ 1 initcall proto_init+0x0/0x12 returned 0 after 0 usecs calling net_dev_init+0x0/0x1a1 @ 1 initcall net_dev_init+0x0/0x1a1 returned 0 after 976 usecs calling neigh_init+0x0/0x71 @ 1 initcall neigh_init+0x0/0x71 returned 0 after 0 usecs calling fib_rules_init+0x0/0xa6 @ 1 initcall fib_rules_init+0x0/0xa6 returned 0 after 0 usecs calling pktsched_init+0x0/0xd0 @ 1 initcall pktsched_init+0x0/0xd0 returned 0 after 0 usecs calling tc_filter_init+0x0/0x4c @ 1 initcall tc_filter_init+0x0/0x4c returned 0 after 0 usecs calling tc_action_init+0x0/0x4c @ 1 initcall tc_action_init+0x0/0x4c returned 0 after 0 usecs calling genl_init+0x0/0x8f @ 1 initcall genl_init+0x0/0x8f returned 0 after 976 usecs calling cipso_v4_init+0x0/0x88 @ 1 initcall cipso_v4_init+0x0/0x88 returned 0 after 0 usecs calling wireless_nlevent_init+0x0/0x12 @ 1 initcall wireless_nlevent_init+0x0/0x12 returned 0 after 0 usecs calling netlbl_init+0x0/0x81 @ 1 NetLabel: Initializing NetLabel: domain hash size = 128 NetLabel: protocols = UNLABELED CIPSOv4 NetLabel: unlabeled traffic allowed by default initcall netlbl_init+0x0/0x81 returned 0 after 0 usecs calling sysctl_init+0x0/0x49 @ 1 initcall sysctl_init+0x0/0x49 returned 0 after 0 usecs calling xen_mc_debugfs+0x0/0x118 @ 1 initcall xen_mc_debugfs+0x0/0x118 returned 0 after 976 usecs calling xen_mmu_debugfs+0x0/0x2be @ 1 initcall xen_mmu_debugfs+0x0/0x2be returned 0 after 976 usecs calling print_all_ICs+0x0/0x567 @ 1 initcall print_all_ICs+0x0/0x567 returned 0 after 976 usecs calling hpet_late_init+0x0/0x1d1 @ 1 initcall hpet_late_init+0x0/0x1d1 returned -19 after 0 usecs calling init_k8_nbs+0x0/0x28 @ 1 initcall init_k8_nbs+0x0/0x28 returned 0 after 0 usecs calling clocksource_done_booting+0x0/0x5e @ 1 Switching to clocksource xen kstop/0 used greatest stack depth: 6296 bytes left initcall clocksource_done_booting+0x0/0x5e returned 0 after 8895 usecs calling ftrace_init_debugfs+0x0/0x241 @ 1 initcall ftrace_init_debugfs+0x0/0x241 returned 0 after 653 usecs calling rb_init_debugfs+0x0/0x2f @ 1 initcall rb_init_debugfs+0x0/0x2f returned 0 after 18 usecs calling tracer_init_debugfs+0x0/0x347 @ 1 initcall tracer_init_debugfs+0x0/0x347 returned 0 after 2609 usecs calling init_trace_printk_function_export+0x0/0x2f @ 1 initcall init_trace_printk_function_export+0x0/0x2f returned 0 after 18 usecs calling stat_workqueue_init+0x0/0x2d @ 1 initcall stat_workqueue_init+0x0/0x2d returned 0 after 21 usecs calling event_trace_init+0x0/0x1ed @ 1 initcall event_trace_init+0x0/0x1ed returned 0 after 87492 usecs calling init_pipe_fs+0x0/0x4d @ 1 initcall init_pipe_fs+0x0/0x4d returned 0 after 212 usecs calling eventpoll_init+0x0/0xda @ 1 initcall eventpoll_init+0x0/0xda returned 0 after 121 usecs calling anon_inode_init+0x0/0x128 @ 1 initcall anon_inode_init+0x0/0x128 returned 0 after 142 usecs calling blk_scsi_ioctl_init+0x0/0x297 @ 1 initcall blk_scsi_ioctl_init+0x0/0x297 returned 0 after 0 usecs calling acpi_event_init+0x0/0x80 @ 1 initcall acpi_event_init+0x0/0x80 returned 0 after 155 usecs calling pnpacpi_init+0x0/0x8c @ 1 pnp: PnP ACPI init ACPI: bus type pnp registered xen: registering gsi 8 triggering 1 polarity 0 xen_allocate_pirq: returning irq 8 for gsi 8 xen: --> irq=8 xen: registering gsi 13 triggering 1 polarity 0 xen_allocate_pirq: returning irq 13 for gsi 13 xen: --> irq=13 xen: registering gsi 4 triggering 1 polarity 0 xen_allocate_pirq: returning irq 4 for gsi 4 xen: --> irq=4 Already setup the GSI :4 xen: registering gsi 3 triggering 1 polarity 0 xen_allocate_pirq: returning irq 3 for gsi 3 xen: --> irq=3 pnp: PnP ACPI: found 14 devices ACPI: ACPI bus type pnp unregistered initcall pnpacpi_init+0x0/0x8c returned 0 after 72877 usecs calling pnp_system_init+0x0/0x12 @ 1 system 00:01: iomem range 0xfed1c000-0xfed1ffff has been reserved system 00:06: ioport range 0xa00-0xa0f has been reserved system 00:06: ioport range 0x290-0x29f has been reserved system 00:07: ioport range 0xca2-0xca3 has been reserved system 00:07: ioport range 0xcf8-0xcff could not be reserved system 00:07: ioport range 0x4d0-0x4d1 has been reserved system 00:07: ioport range 0x800-0x87f has been reserved system 00:07: ioport range 0x500-0x57f could not be reserved system 00:07: iomem range 0xfed1c000-0xfed1ffff has been reserved system 00:07: iomem range 0xfed20000-0xfed3ffff has been reserved system 00:07: iomem range 0xfed40000-0xfed8ffff has been reserved system 00:09: iomem range 0xfec00000-0xfec00fff could not be reserved system 00:09: iomem range 0xfee00000-0xfee00fff has been reserved system 00:0c: iomem range 0xe0000000-0xefffffff has been reserved system 00:0d: iomem range 0xc0000-0xcffff could not be reserved system 00:0d: iomem range 0xe0000-0xfffff could not be reserved system 00:0d: iomem range 0xfed90000-0xffffffff could not be reserved initcall pnp_system_init+0x0/0x12 returned 0 after 93585 usecs calling pcistub_init+0x0/0x1e7 @ 1 initcall pcistub_init+0x0/0x1e7 returned 0 after 1622 usecs calling chr_dev_init+0x0/0xc7 @ 1 initcall chr_dev_init+0x0/0xc7 returned 0 after 922 usecs calling firmware_class_init+0x0/0x79 @ 1 initcall firmware_class_init+0x0/0x79 returned 0 after 96 usecs calling init_pcmcia_bus+0x0/0x84 @ 1 initcall init_pcmcia_bus+0x0/0x84 returned 0 after 124 usecs calling cpufreq_gov_performance_init+0x0/0x12 @ 1 initcall cpufreq_gov_performance_init+0x0/0x12 returned 0 after 16 usecs calling cpufreq_gov_userspace_init+0x0/0x12 @ 1 initcall cpufreq_gov_userspace_init+0x0/0x12 returned 0 after 2 usecs calling init_acpi_pm_clocksource+0x0/0xef @ 1 PM-Timer failed consistency check (0x0xffffff) - aborting. initcall init_acpi_pm_clocksource+0x0/0xef returned -19 after 9691 usecs calling pcibios_assign_resources+0x0/0x74 @ 1 pci 0000:00:01.0: PCI bridge, secondary bus 0000:01 pci 0000:00:01.0: IO window: 0xb000-0xbfff pci 0000:00:01.0: MEM window: 0xf3f00000-0xf6ffffff pci 0000:00:01.0: PREFETCH window: 0x000000c0000000-0x000000cfffffff pci 0000:00:03.0: PCI bridge, secondary bus 0000:02 pci 0000:00:03.0: IO window: disabled pci 0000:00:03.0: MEM window: disabled pci 0000:00:03.0: PREFETCH window: disabled pci 0000:00:07.0: PCI bridge, secondary bus 0000:03 pci 0000:00:07.0: IO window: 0xc000-0xcfff pci 0000:00:07.0: MEM window: 0xf7f00000-0xfaffffff pci 0000:00:07.0: PREFETCH window: 0x000000d0000000-0x000000dfffffff pci 0000:04:00.0: PCI bridge, secondary bus 0000:05 pci 0000:04:00.0: IO window: disabled pci 0000:04:00.0: MEM window: 0xfbc00000-0xfbcfffff pci 0000:04:00.0: PREFETCH window: 0x000000f2f00000-0x000000f2ffffff pci 0000:04:00.2: PCI bridge, secondary bus 0000:06 pci 0000:04:00.2: IO window: disabled pci 0000:04:00.2: MEM window: disabled pci 0000:04:00.2: PREFETCH window: disabled pci 0000:00:1c.0: PCI bridge, secondary bus 0000:04 pci 0000:00:1c.0: IO window: 0x1000-0x1fff pci 0000:00:1c.0: MEM window: 0xfbc00000-0xfbcfffff pci 0000:00:1c.0: PREFETCH window: 0x000000f2f00000-0x000000f2ffffff pci 0000:00:1c.4: PCI bridge, secondary bus 0000:07 pci 0000:00:1c.4: IO window: 0xd000-0xdfff pci 0000:00:1c.4: MEM window: 0xfbd00000-0xfbdfffff pci 0000:00:1c.4: PREFETCH window: 0x000000f0000000-0x000000f01fffff pci 0000:00:1c.5: PCI bridge, secondary bus 0000:08 pci 0000:00:1c.5: IO window: 0xe000-0xefff pci 0000:00:1c.5: MEM window: 0xfbe00000-0xfbefffff pci 0000:00:1c.5: PREFETCH window: 0x000000f0200000-0x000000f03fffff pci 0000:00:1e.0: PCI bridge, secondary bus 0000:09 pci 0000:00:1e.0: IO window: disabled pci 0000:00:1e.0: MEM window: disabled pci 0000:00:1e.0: PREFETCH window: disabled pci 0000:00:01.0: setting latency timer to 64 pci 0000:00:03.0: setting latency timer to 64 pci 0000:00:07.0: setting latency timer to 64 pci 0000:00:1c.0: enabling device (0106 -> 0107) xen: registering gsi 17 triggering 0 polarity 1 alloc irq_desc for 17 on node 0 alloc kstat_irqs on node 0 xen: --> irq=17 pci 0000:00:1c.0: PCI INT A -> GSI 17 (level, low) -> IRQ 17 pci 0000:00:1c.0: setting latency timer to 64 pci 0000:04:00.0: setting latency timer to 64 pci 0000:04:00.2: setting latency timer to 64 xen: registering gsi 17 triggering 0 polarity 1 xen_allocate_pirq: returning irq 17 for gsi 17 xen: --> irq=17 Already setup the GSI :17 pci 0000:00:1c.4: PCI INT A -> GSI 17 (level, low) -> IRQ 17 pci 0000:00:1c.4: setting latency timer to 64 xen: registering gsi 16 triggering 0 polarity 1 alloc irq_desc for 16 on node 0 alloc kstat_irqs on node 0 xen: --> irq=16 pci 0000:00:1c.5: PCI INT B -> GSI 16 (level, low) -> IRQ 16 pci 0000:00:1c.5: setting latency timer to 64 pci 0000:00:1e.0: setting latency timer to 64 pci_bus 0000:00: resource 0 io: [0x00-0xffff] pci_bus 0000:00: resource 1 mem: [0x000000-0xffffffffffffffff] pci_bus 0000:01: resource 0 io: [0xb000-0xbfff] pci_bus 0000:01: resource 1 mem: [0xf3f00000-0xf6ffffff] pci_bus 0000:01: resource 2 pref mem [0xc0000000-0xcfffffff] pci_bus 0000:03: resource 0 io: [0xc000-0xcfff] pci_bus 0000:03: resource 1 mem: [0xf7f00000-0xfaffffff] pci_bus 0000:03: resource 2 pref mem [0xd0000000-0xdfffffff] pci_bus 0000:04: resource 0 io: [0x1000-0x1fff] pci_bus 0000:04: resource 1 mem: [0xfbc00000-0xfbcfffff] pci_bus 0000:04: resource 2 pref mem [0xf2f00000-0xf2ffffff] pci_bus 0000:05: resource 1 mem: [0xfbc00000-0xfbcfffff] pci_bus 0000:05: resource 2 pref mem [0xf2f00000-0xf2ffffff] pci_bus 0000:07: resource 0 io: [0xd000-0xdfff] pci_bus 0000:07: resource 1 mem: [0xfbd00000-0xfbdfffff] pci_bus 0000:07: resource 2 pref mem [0xf0000000-0xf01fffff] pci_bus 0000:08: resource 0 io: [0xe000-0xefff] pci_bus 0000:08: resource 1 mem: [0xfbe00000-0xfbefffff] pci_bus 0000:08: resource 2 pref mem [0xf0200000-0xf03fffff] pci_bus 0000:09: resource 3 io: [0x00-0xffff] pci_bus 0000:09: resource 4 mem: [0x000000-0xffffffffffffffff] initcall pcibios_assign_resources+0x0/0x74 returned 0 after 361318 usecs calling sysctl_core_init+0x0/0x38 @ 1 initcall sysctl_core_init+0x0/0x38 returned 0 after 105 usecs calling inet_init+0x0/0x209 @ 1 NET: Registered protocol family 2 IP route cache hash table entries: 524288 (order: 10, 4194304 bytes) TCP established hash table entries: 524288 (order: 11, 8388608 bytes) TCP bind hash table entries: 65536 (order: 10, 4718592 bytes) TCP: Hash tables configured (established 524288 bind 65536) TCP reno registered initcall inet_init+0x0/0x209 returned 0 after 40865 usecs calling af_unix_init+0x0/0x55 @ 1 NET: Registered protocol family 1 initcall af_unix_init+0x0/0x55 returned 0 after 3095 usecs calling pci_apply_final_quirks+0x0/0x36 @ 1 pci 0000:03:00.0: Boot video device pci 0000:04:00.0: rerouting interrupts for [8086:0370] pci 0000:04:00.2: rerouting interrupts for [8086:0372] initcall pci_apply_final_quirks+0x0/0x36 returned 0 after 13680 usecs calling populate_rootfs+0x0/0x263 @ 1 Trying to unpack rootfs image as initramfs... Freeing initrd memory: 214149k freed initcall populate_rootfs+0x0/0x263 returned 0 after 592711 usecs calling pci_iommu_init+0x0/0x50 @ 1 DMA-API: preallocated 32768 debug entries DMA-API: debugging enabled by kernel config PCI-DMA: Using software bounce buffering for IO (SWIOTLB) DMA: Placing 64MB software IO TLB between ffff880020000000 - ffff880024000000 DMA: software IO TLB at phys 0x20000000 - 0x24000000 initcall pci_iommu_init+0x0/0x50 returned 0 after 61360 usecs calling calgary_fixup_tce_spaces+0x0/0xf9 @ 1 initcall calgary_fixup_tce_spaces+0x0/0xf9 returned -19 after 0 usecs calling i8259A_init_sysfs+0x0/0x22 @ 1 initcall i8259A_init_sysfs+0x0/0x22 returned 0 after 109 usecs calling vsyscall_init+0x0/0x6c @ 1 initcall vsyscall_init+0x0/0x6c returned 0 after 117 usecs calling sbf_init+0x0/0xef @ 1 initcall sbf_init+0x0/0xef returned 0 after 0 usecs calling i8237A_init_sysfs+0x0/0x22 @ 1 initcall i8237A_init_sysfs+0x0/0x22 returned 0 after 80 usecs calling add_rtc_cmos+0x0/0xc4 @ 1 initcall add_rtc_cmos+0x0/0xc4 returned 0 after 3 usecs calling cache_sysfs_init+0x0/0x67 @ 1 initcall cache_sysfs_init+0x0/0x67 returned 0 after 6102 usecs calling mce_init_device+0x0/0x109 @ 1 initcall mce_init_device+0x0/0x109 returned 0 after 2029 usecs calling threshold_init_device+0x0/0x98 @ 1 initcall threshold_init_device+0x0/0x98 returned 0 after 1 usecs calling thermal_throttle_init_device+0x0/0x93 @ 1 initcall thermal_throttle_init_device+0x0/0x93 returned 0 after 0 usecs calling msr_init+0x0/0x14c @ 1 initcall msr_init+0x0/0x14c returned 0 after 1693 usecs calling cpuid_init+0x0/0x14c @ 1 initcall cpuid_init+0x0/0x14c returned 0 after 1636 usecs calling ioapic_init_sysfs+0x0/0xa7 @ 1 initcall ioapic_init_sysfs+0x0/0xa7 returned 0 after 114 usecs calling add_pcspkr+0x0/0x28 @ 1 initcall add_pcspkr+0x0/0x28 returned 0 after 77 usecs calling audit_classes_init+0x0/0xaf @ 1 initcall audit_classes_init+0x0/0xaf returned 0 after 13 usecs calling pt_dump_init+0x0/0x30 @ 1 initcall pt_dump_init+0x0/0x30 returned 0 after 66 usecs calling init_vdso_vars+0x0/0x220 @ 1 initcall init_vdso_vars+0x0/0x220 returned 0 after 46 usecs calling ia32_binfmt_init+0x0/0x14 @ 1 initcall ia32_binfmt_init+0x0/0x14 returned 0 after 32 usecs calling sysenter_setup+0x0/0x2df @ 1 initcall sysenter_setup+0x0/0x2df returned 0 after 3 usecs calling init_sched_debug_procfs+0x0/0x2c @ 1 initcall init_sched_debug_procfs+0x0/0x2c returned 0 after 15 usecs calling proc_schedstat_init+0x0/0x22 @ 1 initcall proc_schedstat_init+0x0/0x22 returned 0 after 10 usecs calling proc_execdomains_init+0x0/0x22 @ 1 initcall proc_execdomains_init+0x0/0x22 returned 0 after 10 usecs calling ioresources_init+0x0/0x3c @ 1 initcall ioresources_init+0x0/0x3c returned 0 after 50 usecs calling uid_cache_init+0x0/0x8d @ 1 initcall uid_cache_init+0x0/0x8d returned 0 after 71 usecs calling init_posix_timers+0x0/0x19f @ 1 initcall init_posix_timers+0x0/0x19f returned 0 after 66 usecs calling init_posix_cpu_timers+0x0/0xe5 @ 1 initcall init_posix_cpu_timers+0x0/0xe5 returned 0 after 0 usecs calling nsproxy_cache_init+0x0/0x2d @ 1 initcall nsproxy_cache_init+0x0/0x2d returned 0 after 88 usecs calling create_proc_profile+0x0/0x282 @ 1 initcall create_proc_profile+0x0/0x282 returned 0 after 0 usecs calling timekeeping_init_device+0x0/0x22 @ 1 initcall timekeeping_init_device+0x0/0x22 returned 0 after 81 usecs calling init_clocksource_sysfs+0x0/0x50 @ 1 initcall init_clocksource_sysfs+0x0/0x50 returned 0 after 113 usecs calling init_timer_list_procfs+0x0/0x2c @ 1 initcall init_timer_list_procfs+0x0/0x2c returned 0 after 11 usecs calling init_tstats_procfs+0x0/0x2c @ 1 initcall init_tstats_procfs+0x0/0x2c returned 0 after 10 usecs calling lockdep_proc_init+0x0/0x7c @ 1 initcall lockdep_proc_init+0x0/0x7c returned 0 after 38 usecs calling futex_init+0x0/0xbe @ 1 initcall futex_init+0x0/0xbe returned 0 after 71 usecs calling proc_dma_init+0x0/0x22 @ 1 initcall proc_dma_init+0x0/0x22 returned 0 after 11 usecs calling proc_modules_init+0x0/0x22 @ 1 initcall proc_modules_init+0x0/0x22 returned 0 after 10 usecs calling kallsyms_init+0x0/0x25 @ 1 initcall kallsyms_init+0x0/0x25 returned 0 after 10 usecs calling snapshot_device_init+0x0/0x12 @ 1 initcall snapshot_device_init+0x0/0x12 returned 0 after 83 usecs calling crash_save_vmcoreinfo_init+0x0/0x46d @ 1 initcall crash_save_vmcoreinfo_init+0x0/0x46d returned 0 after 22 usecs calling crash_notes_memory_init+0x0/0x38 @ 1 initcall crash_notes_memory_init+0x0/0x38 returned 0 after 11 usecs calling pid_namespaces_init+0x0/0x2d @ 1 initcall pid_namespaces_init+0x0/0x2d returned 0 after 100 usecs calling ikconfig_init+0x0/0x39 @ 1 initcall ikconfig_init+0x0/0x39 returned 0 after 11 usecs calling audit_init+0x0/0x153 @ 1 audit: initializing netlink socket (disabled) type=2000 audit(1275218265.439:1): initialized initcall audit_init+0x0/0x153 returned 0 after 8236 usecs calling audit_tree_init+0x0/0x49 @ 1 initcall audit_tree_init+0x0/0x49 returned 0 after 2 usecs calling init_kprobes+0x0/0x19e @ 1 initcall init_kprobes+0x0/0x19e returned 0 after 12070 usecs calling hung_task_init+0x0/0x53 @ 1 initcall hung_task_init+0x0/0x53 returned 0 after 203 usecs calling utsname_sysctl_init+0x0/0x14 @ 1 initcall utsname_sysctl_init+0x0/0x14 returned 0 after 83 usecs calling init_tracepoints+0x0/0x17 @ 1 initcall init_tracepoints+0x0/0x17 returned 0 after 0 usecs calling init_lstats_procfs+0x0/0x25 @ 1 initcall init_lstats_procfs+0x0/0x25 returned 0 after 12 usecs calling ftrace_mod_cmd_init+0x0/0x12 @ 1 initcall ftrace_mod_cmd_init+0x0/0x12 returned 0 after 18 usecs calling init_events+0x0/0x63 @ 1 initcall init_events+0x0/0x63 returned 0 after 11 usecs calling init_sched_switch_trace+0x0/0x12 @ 1 initcall init_sched_switch_trace+0x0/0x12 returned 0 after 3 usecs calling init_stack_trace+0x0/0x12 @ 1 initcall init_stack_trace+0x0/0x12 returned 0 after 1 usecs calling init_function_trace+0x0/0x3e @ 1 initcall init_function_trace+0x0/0x3e returned 0 after 3 usecs calling init_wakeup_tracer+0x0/0x22 @ 1 initcall init_wakeup_tracer+0x0/0x22 returned 0 after 3 usecs calling stack_trace_init+0x0/0x6b @ 1 initcall stack_trace_init+0x0/0x6b returned 0 after 38 usecs calling init_mmio_trace+0x0/0x12 @ 1 initcall init_mmio_trace+0x0/0x12 returned 0 after 1 usecs calling init_graph_trace+0x0/0x32 @ 1 initcall init_graph_trace+0x0/0x32 returned 0 after 2 usecs calling init_kmem_tracer+0x0/0x56 @ 1 initcall init_kmem_tracer+0x0/0x56 returned 0 after 4 usecs calling init_blk_tracer+0x0/0x57 @ 1 initcall init_blk_tracer+0x0/0x57 returned 0 after 3 usecs calling perf_event_sysfs_init+0x0/0x19 @ 1 initcall perf_event_sysfs_init+0x0/0x19 returned 0 after 14 usecs calling init_per_zone_wmark_min+0x0/0x68 @ 1 initcall init_per_zone_wmark_min+0x0/0x68 returned 0 after 899 usecs calling kswapd_init+0x0/0x78 @ 1 initcall kswapd_init+0x0/0x78 returned 0 after 336 usecs calling setup_vmstat+0x0/0xc3 @ 1 initcall setup_vmstat+0x0/0xc3 returned 0 after 180 usecs calling mm_sysfs_init+0x0/0x29 @ 1 initcall mm_sysfs_init+0x0/0x29 returned 0 after 9 usecs calling proc_vmalloc_init+0x0/0x25 @ 1 initcall proc_vmalloc_init+0x0/0x25 returned 0 after 10 usecs calling procswaps_init+0x0/0x22 @ 1 initcall procswaps_init+0x0/0x22 returned 0 after 10 usecs calling hugetlb_init+0x0/0x3c8 @ 1 HugeTLB registered 2 MB page size, pre-allocated 0 pages initcall hugetlb_init+0x0/0x3c8 returned 0 after 5058 usecs calling slab_proc_init+0x0/0x25 @ 1 initcall slab_proc_init+0x0/0x25 returned 0 after 11 usecs calling slab_sysfs_init+0x0/0xf0 @ 1 initcall slab_sysfs_init+0x0/0xf0 returned 0 after 17492 usecs calling fasync_init+0x0/0x2a @ 1 initcall fasync_init+0x0/0x2a returned 0 after 247 usecs calling proc_filesystems_init+0x0/0x22 @ 1 initcall proc_filesystems_init+0x0/0x22 returned 0 after 12 usecs calling dnotify_init+0x0/0x80 @ 1 initcall dnotify_init+0x0/0x80 returned 0 after 546 usecs calling inotify_setup+0x0/0x12 @ 1 initcall inotify_setup+0x0/0x12 returned 0 after 0 usecs calling inotify_user_setup+0x0/0xbe @ 1 initcall inotify_user_setup+0x0/0xbe returned 0 after 651 usecs calling aio_setup+0x0/0xa5 @ 1 initcall aio_setup+0x0/0xa5 returned 0 after 3119 usecs calling proc_locks_init+0x0/0x22 @ 1 initcall proc_locks_init+0x0/0x22 returned 0 after 13 usecs calling init_sys32_ioctl+0x0/0x85 @ 1 initcall init_sys32_ioctl+0x0/0x85 returned 0 after 12 usecs calling init_mbcache+0x0/0x14 @ 1 initcall init_mbcache+0x0/0x14 returned 0 after 1 usecs calling dquot_init+0x0/0x105 @ 1 VFS: Disk quotas dquot_6.5.2 Dquot-cache hash table entries: 512 (order 0, 4096 bytes) initcall dquot_init+0x0/0x105 returned 0 after 8080 usecs calling init_v2_quota_format+0x0/0x12 @ 1 initcall init_v2_quota_format+0x0/0x12 returned 0 after 16 usecs calling proc_cmdline_init+0x0/0x22 @ 1 initcall proc_cmdline_init+0x0/0x22 returned 0 after 12 usecs calling proc_cpuinfo_init+0x0/0x22 @ 1 initcall proc_cpuinfo_init+0x0/0x22 returned 0 after 10 usecs calling proc_devices_init+0x0/0x22 @ 1 initcall proc_devices_init+0x0/0x22 returned 0 after 43 usecs calling proc_interrupts_init+0x0/0x22 @ 1 initcall proc_interrupts_init+0x0/0x22 returned 0 after 10 usecs calling proc_loadavg_init+0x0/0x22 @ 1 initcall proc_loadavg_init+0x0/0x22 returned 0 after 10 usecs calling proc_meminfo_init+0x0/0x22 @ 1 initcall proc_meminfo_init+0x0/0x22 returned 0 after 10 usecs calling proc_stat_init+0x0/0x22 @ 1 initcall proc_stat_init+0x0/0x22 returned 0 after 10 usecs calling proc_uptime_init+0x0/0x22 @ 1 initcall proc_uptime_init+0x0/0x22 returned 0 after 10 usecs calling proc_version_init+0x0/0x22 @ 1 initcall proc_version_init+0x0/0x22 returned 0 after 10 usecs calling proc_softirqs_init+0x0/0x22 @ 1 initcall proc_softirqs_init+0x0/0x22 returned 0 after 10 usecs calling proc_kcore_init+0x0/0xa9 @ 1 initcall proc_kcore_init+0x0/0xa9 returned 0 after 31 usecs calling vmcore_init+0x0/0x8d2 @ 1 initcall vmcore_init+0x0/0x8d2 returned 0 after 0 usecs calling proc_kmsg_init+0x0/0x25 @ 1 initcall proc_kmsg_init+0x0/0x25 returned 0 after 10 usecs calling proc_page_init+0x0/0x42 @ 1 initcall proc_page_init+0x0/0x42 returned 0 after 19 usecs calling init_devpts_fs+0x0/0x4c @ 1 initcall init_devpts_fs+0x0/0x4c returned 0 after 239 usecs calling init_ext3_fs+0x0/0x71 @ 1 initcall init_ext3_fs+0x0/0x71 returned 0 after 568 usecs calling init_ext4_fs+0x0/0xea @ 1 initcall init_ext4_fs+0x0/0xea returned 0 after 1547 usecs calling journal_init+0x0/0x93 @ 1 initcall journal_init+0x0/0x93 returned 0 after 975 usecs calling journal_init+0x0/0xec @ 1 initcall journal_init+0x0/0xec returned 0 after 1124 usecs calling init_ramfs_fs+0x0/0x12 @ 1 initcall init_ramfs_fs+0x0/0x12 returned 0 after 3 usecs calling init_hugetlbfs_fs+0x0/0x98 @ 1 initcall init_hugetlbfs_fs+0x0/0x98 returned 0 after 444 usecs calling init_iso9660_fs+0x0/0x71 @ 1 initcall init_iso9660_fs+0x0/0x71 returned 0 after 306 usecs calling init_nls_cp437+0x0/0x12 @ 1 initcall init_nls_cp437+0x0/0x12 returned 0 after 16 usecs calling init_nls_ascii+0x0/0x12 @ 1 initcall init_nls_ascii+0x0/0x12 returned 0 after 1 usecs calling ipc_init+0x0/0x23 @ 1 msgmni has been set to 21017 initcall ipc_init+0x0/0x23 returned 0 after 2645 usecs calling ipc_sysctl_init+0x0/0x14 @ 1 initcall ipc_sysctl_init+0x0/0x14 returned 0 after 140 usecs calling init_mqueue_fs+0x0/0xc9 @ 1 initcall init_mqueue_fs+0x0/0xc9 returned 0 after 600 usecs calling key_proc_init+0x0/0x59 @ 1 initcall key_proc_init+0x0/0x59 returned 0 after 23 usecs calling selinux_nf_ip_init+0x0/0x60 @ 1 SELinux: Registering netfilter hooks initcall selinux_nf_ip_init+0x0/0x60 returned 0 after 3407 usecs calling init_sel_fs+0x0/0x68 @ 1 initcall init_sel_fs+0x0/0x68 returned 0 after 996 usecs calling selnl_init+0x0/0x4d @ 1 initcall selnl_init+0x0/0x4d returned 0 after 54 usecs calling sel_netif_init+0x0/0x66 @ 1 initcall sel_netif_init+0x0/0x66 returned 0 after 6 usecs calling sel_netnode_init+0x0/0x73 @ 1 initcall sel_netnode_init+0x0/0x73 returned 0 after 2 usecs calling sel_netport_init+0x0/0x73 @ 1 initcall sel_netport_init+0x0/0x73 returned 0 after 9 usecs calling aurule_init+0x0/0x37 @ 1 initcall aurule_init+0x0/0x37 returned 0 after 0 usecs calling crypto_wq_init+0x0/0x32 @ 1 initcall crypto_wq_init+0x0/0x32 returned 0 after 2705 usecs calling crypto_algapi_init+0x0/0xd @ 1 initcall crypto_algapi_init+0x0/0xd returned 0 after 49 usecs calling skcipher_module_init+0x0/0x35 @ 1 initcall skcipher_module_init+0x0/0x35 returned 0 after 0 usecs calling chainiv_module_init+0x0/0x12 @ 1 initcall chainiv_module_init+0x0/0x12 returned 0 after 37 usecs calling eseqiv_module_init+0x0/0x12 @ 1 initcall eseqiv_module_init+0x0/0x12 returned 0 after 2 usecs calling hmac_module_init+0x0/0x12 @ 1 initcall hmac_module_init+0x0/0x12 returned 0 after 1 usecs calling md5_mod_init+0x0/0x12 @ 1 cryptomgr_test used greatest stack depth: 5672 bytes left initcall md5_mod_init+0x0/0x12 returned 0 after 415 usecs calling sha1_generic_mod_init+0x0/0x12 @ 1 initcall sha1_generic_mod_init+0x0/0x12 returned 0 after 271 usecs calling crc32c_mod_init+0x0/0x12 @ 1 initcall crc32c_mod_init+0x0/0x12 returned 0 after 330 usecs calling krng_mod_init+0x0/0x12 @ 1 alg: No test for stdrng (krng) initcall krng_mod_init+0x0/0x12 returned 0 after 212 usecs calling proc_genhd_init+0x0/0x3c @ 1 initcall proc_genhd_init+0x0/0x3c returned 0 after 24 usecs calling bsg_init+0x0/0x132 @ 1 Block layer SCSI generic (bsg) driver version 0.4 loaded (major 252) initcall bsg_init+0x0/0x132 returned 0 after 308 usecs calling noop_init+0x0/0x14 @ 1 io scheduler noop registered initcall noop_init+0x0/0x14 returned 0 after 19 usecs calling as_init+0x0/0x14 @ 1 io scheduler anticipatory registered initcall as_init+0x0/0x14 returned 0 after 2 usecs calling deadline_init+0x0/0x14 @ 1 io scheduler deadline registered initcall deadline_init+0x0/0x14 returned 0 after 2 usecs calling cfq_init+0x0/0x94 @ 1 io scheduler cfq registered (default) initcall cfq_init+0x0/0x94 returned 0 after 495 usecs calling debug_objects_init_debugfs+0x0/0x64 @ 1 initcall debug_objects_init_debugfs+0x0/0x64 returned 0 after 80 usecs calling percpu_counter_startup+0x0/0x38 @ 1 initcall percpu_counter_startup+0x0/0x38 returned 0 after 2 usecs calling dynamic_debug_init+0x0/0x127 @ 1 initcall dynamic_debug_init+0x0/0x127 returned 0 after 328 usecs calling pci_proc_init+0x0/0x6b @ 1 initcall pci_proc_init+0x0/0x6b returned 0 after 820 usecs calling pcie_portdrv_init+0x0/0x4c @ 1 alloc irq_desc for 4269 on node 0 alloc kstat_irqs on node 0 pcieport 0000:00:01.0: setting latency timer to 64 alloc irq_desc for 4268 on node 0 alloc kstat_irqs on node 0 pcieport 0000:00:03.0: setting latency timer to 64 alloc irq_desc for 4267 on node 0 alloc kstat_irqs on node 0 pcieport 0000:00:07.0: setting latency timer to 64 alloc irq_desc for 4266 on node 0 alloc kstat_irqs on node 0 pcieport 0000:00:1c.0: setting latency timer to 64 alloc irq_desc for 4265 on node 0 alloc kstat_irqs on node 0 pcieport 0000:00:1c.4: setting latency timer to 64 alloc irq_desc for 4264 on node 0 alloc kstat_irqs on node 0 pcieport 0000:00:1c.5: setting latency timer to 64 initcall pcie_portdrv_init+0x0/0x4c returned 0 after 4286 usecs calling aer_service_init+0x0/0x2b @ 1 aer 0000:00:01.0:pcie02: AER service couldn't init device: no _OSC support aer 0000:00:03.0:pcie02: AER service couldn't init device: no _OSC support aer 0000:00:07.0:pcie02: AER service couldn't init device: no _OSC support initcall aer_service_init+0x0/0x2b returned 0 after 202 usecs calling pci_hotplug_init+0x0/0x1d @ 1 pci_hotplug: PCI Hot Plug PCI Core version: 0.5 initcall pci_hotplug_init+0x0/0x1d returned 0 after 1 usecs calling pcied_init+0x0/0x79 @ 1 pciehp: PCI Express Hot Plug Controller Driver version: 0.4 initcall pcied_init+0x0/0x79 returned 0 after 646 usecs calling acpiphp_init+0x0/0x5f @ 1 acpiphp: ACPI Hot Plug PCI Controller Driver version: 0.5 initcall acpiphp_init+0x0/0x5f returned -19 after 2301 usecs calling pci_stub_init+0x0/0x139 @ 1 pci-stub: invalid id string "" initcall pci_stub_init+0x0/0x139 returned 0 after 146 usecs calling fb_console_init+0x0/0x11d @ 1 cryptomgr_test used greatest stack depth: 5400 bytes left initcall fb_console_init+0x0/0x11d returned 0 after 291391 usecs calling xenfb_init+0x0/0x5d @ 1 initcall xenfb_init+0x0/0x5d returned -19 after 0 usecs calling vesafb_init+0x0/0x23a @ 1 initcall vesafb_init+0x0/0x23a returned 0 after 195 usecs calling efifb_init+0x0/0x1ed @ 1 initcall efifb_init+0x0/0x1ed returned -19 after 4 usecs calling acpi_reserve_resources+0x0/0xeb @ 1 initcall acpi_reserve_resources+0x0/0xeb returned 0 after 9 usecs calling irqrouter_init_sysfs+0x0/0x38 @ 1 initcall irqrouter_init_sysfs+0x0/0x38 returned 0 after 78 usecs calling acpi_ac_init+0x0/0x45 @ 1 initcall acpi_ac_init+0x0/0x45 returned 0 after 182 usecs calling acpi_button_init+0x0/0x56 @ 1 input: Power Button as /devices/LNXSYSTM:00/LNXSYBUS:00/PNP0C0C:00/input/input0 ACPI: Power Button [PWRB] input: Power Button as /devices/LNXSYSTM:00/LNXPWRBN:00/input/input1 ACPI: Power Button [PWRF] initcall acpi_button_init+0x0/0x56 returned 0 after 18361 usecs calling acpi_fan_init+0x0/0x56 @ 1 initcall acpi_fan_init+0x0/0x56 returned 0 after 124 usecs calling acpi_pci_slot_init+0x0/0x20 @ 1 initcall acpi_pci_slot_init+0x0/0x20 returned 0 after 1902 usecs calling acpi_processor_init+0x0/0x132 @ 1 ACPI: SSDT 00000000bf77e1e0 02B94 (v01 DpgPmm P001Ist 00000011 INTL 20051117) ACPI: SSDT 00000000bf780d80 00980 (v01 PmRef P001Cst 00003001 INTL 20051117) ACPI: SSDT 00000000bf781700 006E2 (v01 PmRef Cpu0Tst 00003000 INTL 20051117) (XEN) cpuid.MWAIT[.eax=40, .ebx=40, .ecx=3, .edx=1120] (XEN) Monitor-Mwait will be used to enter C-1 state (XEN) cpuid.MWAIT[.eax=40, .ebx=40, .ecx=3, .edx=1120] (XEN) Monitor-Mwait will be used to enter C-3 state (XEN) cpuid.MWAIT[.eax=40, .ebx=40, .ecx=3, .edx=1120] (XEN) Monitor-Mwait will be used to enter C-3 state ACPI: CPU-1 (power states: C1[C1] C2[C3] C3[C3]) (XEN) cpuid.MWAIT[.eax=40, .ebx=40, .ecx=3, .edx=1120] (XEN) Monitor-Mwait will be used to enter C-1 state (XEN) cpuid.MWAIT[.eax=40, .ebx=40, .ecx=3, .edx=1120] (XEN) Monitor-Mwait will be used to enter C-3 state (XEN) cpuid.MWAIT[.eax=40, .ebx=40, .ecx=3, .edx=1120] (XEN) Monitor-Mwait will be used to enter C-3 state ACPI: CPU-1 (power states: C1[C1] C2[C3] C3[C3]) (XEN) cpuid.MWAIT[.eax=40, .ebx=40, .ecx=3, .edx=1120] (XEN) Monitor-Mwait will be used to enter C-1 state (XEN) cpuid.MWAIT[.eax=40, .ebx=40, .ecx=3, .edx=1120] (XEN) Monitor-Mwait will be used to enter C-3 state (XEN) cpuid.MWAIT[.eax=40, .ebx=40, .ecx=3, .edx=1120] (XEN) Monitor-Mwait will be used to enter C-3 state ACPI: CPU-1 (power states: C1[C1] C2[C3] C3[C3]) (XEN) cpuid.MWAIT[.eax=40, .ebx=40, .ecx=3, .edx=1120] (XEN) Monitor-Mwait will be used to enter C-1 state (XEN) cpuid.MWAIT[.eax=40, .ebx=40, .ecx=3, .edx=1120] (XEN) Monitor-Mwait will be used to enter C-3 state (XEN) cpuid.MWAIT[.eax=40, .ebx=40, .ecx=3, .edx=1120] (XEN) Monitor-Mwait will be used to enter C-3 state ACPI: CPU-1 (power states: C1[C1] C2[C3] C3[C3]) (XEN) cpuid.MWAIT[.eax=40, .ebx=40, .ecx=3, .edx=1120] (XEN) Monitor-Mwait will be used to enter C-1 state (XEN) cpuid.MWAIT[.eax=40, .ebx=40, .ecx=3, .edx=1120] (XEN) Monitor-Mwait will be used to enter C-3 state (XEN) cpuid.MWAIT[.eax=40, .ebx=40, .ecx=3, .edx=1120] (XEN) Monitor-Mwait will be used to enter C-3 state ACPI: CPU-1 (power states: C1[C1] C2[C3] C3[C3]) (XEN) cpuid.MWAIT[.eax=40, .ebx=40, .ecx=3, .edx=1120] (XEN) Monitor-Mwait will be used to enter C-1 state (XEN) cpuid.MWAIT[.eax=40, .ebx=40, .ecx=3, .edx=1120] (XEN) Monitor-Mwait will be used to enter C-3 state (XEN) cpuid.MWAIT[.eax=40, .ebx=40, .ecx=3, .edx=1120] (XEN) Monitor-Mwait will be used to enter C-3 state ACPI: CPU-1 (power states: C1[C1] C2[C3] C3[C3]) (XEN) cpuid.MWAIT[.eax=40, .ebx=40, .ecx=3, .edx=1120] (XEN) Monitor-Mwait will be used to enter C-1 state (XEN) cpuid.MWAIT[.eax=40, .ebx=40, .ecx=3, .edx=1120] (XEN) Monitor-Mwait will be used to enter C-3 state (XEN) cpuid.MWAIT[.eax=40, .ebx=40, .ecx=3, .edx=1120] (XEN) Monitor-Mwait will be used to enter C-3 state ACPI: CPU-1 (power states: C1[C1] C2[C3] C3[C3]) (XEN) cpuid.MWAIT[.eax=40, .ebx=40, .ecx=3, .edx=1120] (XEN) Monitor-Mwait will be used to enter C-1 state (XEN) cpuid.MWAIT[.eax=40, .ebx=40, .ecx=3, .edx=1120] (XEN) Monitor-Mwait will be used to enter C-3 state (XEN) cpuid.MWAIT[.eax=40, .ebx=40, .ecx=3, .edx=1120] (XEN) Monitor-Mwait will be used to enter C-3 state ACPI: CPU-1 (power states: C1[C1] C2[C3] C3[C3]) (XEN) cpuid.MWAIT[.eax=40, .ebx=40, .ecx=3, .edx=1120] (XEN) Monitor-Mwait will be used to enter C-1 state (XEN) cpuid.MWAIT[.eax=40, .ebx=40, .ecx=3, .edx=1120] (XEN) Monitor-Mwait will be used to enter C-3 state (XEN) cpuid.MWAIT[.eax=40, .ebx=40, .ecx=3, .edx=1120] (XEN) Monitor-Mwait will be used to enter C-3 state ACPI: CPU-1 (power states: C1[C1] C2[C3] C3[C3]) (XEN) cpuid.MWAIT[.eax=40, .ebx=40, .ecx=3, .edx=1120] (XEN) Monitor-Mwait will be used to enter C-1 state (XEN) cpuid.MWAIT[.eax=40, .ebx=40, .ecx=3, .edx=1120] (XEN) Monitor-Mwait will be used to enter C-3 state (XEN) cpuid.MWAIT[.eax=40, .ebx=40, .ecx=3, .edx=1120] (XEN) Monitor-Mwait will be used to enter C-3 state ACPI: CPU-1 (power states: C1[C1] C2[C3] C3[C3]) (XEN) cpuid.MWAIT[.eax=40, .ebx=40, .ecx=3, .edx=1120] (XEN) Monitor-Mwait will be used to enter C-1 state (XEN) cpuid.MWAIT[.eax=40, .ebx=40, .ecx=3, .edx=1120] (XEN) Monitor-Mwait will be used to enter C-3 state (XEN) cpuid.MWAIT[.eax=40, .ebx=40, .ecx=3, .edx=1120] (XEN) Monitor-Mwait will be used to enter C-3 state ACPI: CPU-1 (power states: C1[C1] C2[C3] C3[C3]) (XEN) cpuid.MWAIT[.eax=40, .ebx=40, .ecx=3, .edx=1120] (XEN) Monitor-Mwait will be used to enter C-1 state (XEN) cpuid.MWAIT[.eax=40, .ebx=40, .ecx=3, .edx=1120] (XEN) Monitor-Mwait will be used to enter C-3 state (XEN) cpuid.MWAIT[.eax=40, .ebx=40, .ecx=3, .edx=1120] (XEN) Monitor-Mwait will be used to enter C-3 state ACPI: CPU-1 (power states: C1[C1] C2[C3] C3[C3]) (XEN) cpuid.MWAIT[.eax=40, .ebx=40, .ecx=3, .edx=1120] (XEN) Monitor-Mwait will be used to enter C-1 state (XEN) cpuid.MWAIT[.eax=40, .ebx=40, .ecx=3, .edx=1120] (XEN) Monitor-Mwait will be used to enter C-3 state (XEN) cpuid.MWAIT[.eax=40, .ebx=40, .ecx=3, .edx=1120] (XEN) Monitor-Mwait will be used to enter C-3 state ACPI: CPU-1 (power states: C1[C1] C2[C3] C3[C3]) (XEN) cpuid.MWAIT[.eax=40, .ebx=40, .ecx=3, .edx=1120] (XEN) Monitor-Mwait will be used to enter C-1 state (XEN) cpuid.MWAIT[.eax=40, .ebx=40, .ecx=3, .edx=1120] (XEN) Monitor-Mwait will be used to enter C-3 state (XEN) cpuid.MWAIT[.eax=40, .ebx=40, .ecx=3, .edx=1120] (XEN) Monitor-Mwait will be used to enter C-3 state ACPI: CPU-1 (power states: C1[C1] C2[C3] C3[C3]) (XEN) cpuid.MWAIT[.eax=40, .ebx=40, .ecx=3, .edx=1120] (XEN) Monitor-Mwait will be used to enter C-1 state (XEN) cpuid.MWAIT[.eax=40, .ebx=40, .ecx=3, .edx=1120] (XEN) Monitor-Mwait will be used to enter C-3 state (XEN) cpuid.MWAIT[.eax=40, .ebx=40, .ecx=3, .edx=1120] (XEN) Monitor-Mwait will be used to enter C-3 state ACPI: CPU-1 (power states: C1[C1] C2[C3] C3[C3]) (XEN) cpuid.MWAIT[.eax=40, .ebx=40, .ecx=3, .edx=1120] (XEN) Monitor-Mwait will be used to enter C-1 state (XEN) cpuid.MWAIT[.eax=40, .ebx=40, .ecx=3, .edx=1120] (XEN) Monitor-Mwait will be used to enter C-3 state (XEN) cpuid.MWAIT[.eax=40, .ebx=40, .ecx=3, .edx=1120] (XEN) Monitor-Mwait will be used to enter C-3 state ACPI: CPU-1 (power states: C1[C1] C2[C3] C3[C3]) initcall acpi_processor_init+0x0/0x132 returned 0 after 629629 usecs calling acpi_container_init+0x0/0x42 @ 1 initcall acpi_container_init+0x0/0x42 returned 0 after 13724 usecs calling acpi_thermal_init+0x0/0x7b @ 1 initcall acpi_thermal_init+0x0/0x7b returned 0 after 169 usecs calling acpi_battery_init+0x0/0x16 @ 1 initcall acpi_battery_init+0x0/0x16 returned 0 after 30 usecs calling 1_acpi_battery_init_async+0x0/0x3c @ 233 initcall 1_acpi_battery_init_async+0x0/0x3c returned 0 after 244 usecs calling evtchn_init+0x0/0x7e @ 1 Event-channel device installed. initcall evtchn_init+0x0/0x7e returned 0 after 2902 usecs calling gntdev_init+0x0/0x3d @ 1 initcall gntdev_init+0x0/0x3d returned 0 after 117 usecs calling pciback_init+0x0/0x15f @ 1 initcall pciback_init+0x0/0x15f returned 0 after 4695 usecs calling blkif_init+0x0/0x171 @ 1 initcall blkif_init+0x0/0x171 returned 0 after 3660 usecs calling blktap_init+0x0/0xa7 @ 1 blktap_device_init: blktap device major 253 blktap_ring_init: blktap ring major: 251 initcall blktap_init+0x0/0xa7 returned 0 after 10464 usecs calling netback_init+0x0/0x207 @ 1 registering netback initcall netback_init+0x0/0x207 returned 0 after 2961 usecs calling hypervisor_subsys_init+0x0/0x25 @ 1 initcall hypervisor_subsys_init+0x0/0x25 returned 0 after 0 usecs calling hyper_sysfs_init+0x0/0xf2 @ 1 initcall hyper_sysfs_init+0x0/0xf2 returned 0 after 79 usecs calling platform_pci_module_init+0x0/0xa3 @ 1 xen-platform-pcifailed backend handshake: unrecognised magic value initcall platform_pci_module_init+0x0/0xa3 returned -19 after 5839 usecs calling mcelog_init+0x0/0x1b0 @ 1 alloc irq_desc for 4263 on node 0 alloc kstat_irqs on node 0 initcall mcelog_init+0x0/0x1b0 returned 0 after 6418 usecs calling rand_initialize+0x0/0x31 @ 1 initcall rand_initialize+0x0/0x31 returned 0 after 30 usecs calling tty_init+0x0/0xf5 @ 1 initcall tty_init+0x0/0xf5 returned 0 after 6277 usecs calling pty_init+0x0/0x336 @ 1 initcall pty_init+0x0/0x336 returned 0 after 243 usecs calling sysrq_init+0x0/0x25 @ 1 initcall sysrq_init+0x0/0x25 returned 0 after 14 usecs calling xen_hvc_init+0x0/0xe2 @ 1 alloc irq_desc for 4262 on node 0 alloc kstat_irqs on node 0 initcall xen_hvc_init+0x0/0xe2 returned 0 after 6895 usecs calling raw_init+0x0/0xe5 @ 1 initcall raw_init+0x0/0xe5 returned 0 after 149 usecs calling hpet_init+0x0/0x6a @ 1 hpet_acpi_add: no address or irqs in _CRS initcall hpet_init+0x0/0x6a returned 0 after 4307 usecs calling nvram_init+0x0/0x82 @ 1 Non-volatile memory driver v1.3 initcall nvram_init+0x0/0x82 returned 0 after 2886 usecs calling agp_init+0x0/0x26 @ 1 Linux agpgart interface v0.103 initcall agp_init+0x0/0x26 returned 0 after 2792 usecs calling agp_intel_init+0x0/0x29 @ 1 initcall agp_intel_init+0x0/0x29 returned 0 after 111 usecs calling agp_sis_init+0x0/0x29 @ 1 initcall agp_sis_init+0x0/0x29 returned 0 after 133 usecs calling agp_via_init+0x0/0x29 @ 1 initcall agp_via_init+0x0/0x29 returned 0 after 101 usecs calling init_tis+0x0/0x91 @ 1 initcall init_tis+0x0/0x91 returned 0 after 65 usecs calling cn_proc_init+0x0/0x3d @ 1 initcall cn_proc_init+0x0/0x3d returned 0 after 45 usecs calling serial8250_init+0x0/0x143 @ 1 Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled async_waiting @ 1 async_continuing @ 1 after 10 usec (XEN) irq.c:1139:d0 Cannot bind IRQ 4 to guest. In use by 'ns16550'. (XEN) irq.c:1139:d0 Cannot bind IRQ 2 to guest. In use by 'cascade'. (XEN) irq.c:1139:d0 Cannot bind IRQ 4 to guest. In use by 'ns16550'. (XEN) irq.c:1139:d0 Cannot bind IRQ 2 to guest. In use by 'cascade'. async_waiting @ 1 async_continuing @ 1 after 1 usec (XEN) irq.c:1139:d0 Cannot bind IRQ 4 to guest. In use by 'ns16550'. (XEN) irq.c:1139:d0 Cannot bind IRQ 2 to guest. In use by 'cascade'. (XEN) irq.c:1139:d0 Cannot bind IRQ 4 to guest. In use by 'ns16550'. (XEN) irq.c:1139:d0 Cannot bind IRQ 2 to guest. In use by 'cascade'. serial8250: ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A initcall serial8250_init+0x0/0x143 returned 0 after 308270 usecs calling serial8250_pnp_init+0x0/0x12 @ 1 00:0b: ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A initcall serial8250_pnp_init+0x0/0x12 returned 0 after 5240 usecs calling serial8250_pci_init+0x0/0x1b @ 1 initcall serial8250_pci_init+0x0/0x1b returned 0 after 114 usecs calling init_kgdboc+0x0/0x16 @ 1 initcall init_kgdboc+0x0/0x16 returned 0 after 0 usecs calling topology_sysfs_init+0x0/0x63 @ 1 initcall topology_sysfs_init+0x0/0x63 returned 0 after 470 usecs calling brd_init+0x0/0x16d @ 1 brd: module loaded initcall brd_init+0x0/0x16d returned 0 after 8259 usecs calling loop_init+0x0/0x197 @ 1 loop: module loaded initcall loop_init+0x0/0x197 returned 0 after 4968 usecs calling init_kgdbts+0x0/0x16 @ 1 initcall init_kgdbts+0x0/0x16 returned 0 after 0 usecs calling mac_hid_init+0x0/0xd5 @ 1 input: Macintosh mouse button emulation as /devices/virtual/input/input2 initcall mac_hid_init+0x0/0xd5 returned 0 after 6552 usecs calling scsi_dh_init+0x0/0x3f @ 1 initcall scsi_dh_init+0x0/0x3f returned 0 after 1 usecs calling init_sd+0x0/0x17b @ 1 initcall init_sd+0x0/0x17b returned 0 after 420 usecs calling init_sr+0x0/0x49 @ 1 initcall init_sr+0x0/0x49 returned 0 after 51 usecs calling init_sg+0x0/0x123 @ 1 initcall init_sg+0x0/0x123 returned 0 after 136 usecs calling ahci_init+0x0/0x1b @ 1 ahci 0000:00:1f.2: version 3.0 xen: registering gsi 19 triggering 0 polarity 1 alloc irq_desc for 19 on node 0 alloc kstat_irqs on node 0 xen: --> irq=19 ahci 0000:00:1f.2: PCI INT B -> GSI 19 (level, low) -> IRQ 19 alloc irq_desc for 4261 on node 0 alloc kstat_irqs on node 0 ahci: SSS flag set, parallel bus scan disabled ahci 0000:00:1f.2: AHCI 0001.0200 32 slots 6 ports 3 Gbps 0x3f impl SATA mode ahci 0000:00:1f.2: flags: 64bit ncq sntf stag pm led clo pio slum part ccc ems sxs ahci 0000:00:1f.2: setting latency timer to 64 scsi0 : ahci scsi1 : ahci scsi2 : ahci scsi3 : ahci scsi4 : ahci scsi5 : ahci ata1: SATA max UDMA/133 abar m2048@0xfbbd6000 port 0xfbbd6100 irq 4261 ata2: SATA max UDMA/133 abar m2048@0xfbbd6000 port 0xfbbd6180 irq 4261 ata3: SATA max UDMA/133 irq_stat 0x00400040, connection status changed irq 4261 ata4: SATA max UDMA/133 irq_stat 0x00400040, connection status changed irq 4261 ata5: SATA max UDMA/133 abar m2048@0xfbbd6000 port 0xfbbd6300 irq 4261 ata6: SATA max UDMA/133 abar m2048@0xfbbd6000 port 0xfbbd6380 irq 4261 calling 2_async_port_probe+0x0/0xc9 @ 233 initcall ahci_init+0x0/0x1b returned 0 after 109920 usecs calling piix_init+0x0/0x29 @ 1 initcall piix_init+0x0/0x29 returned 0 after 136 usecs calling fixed_mdio_bus_init+0x0/0xd0 @ 1 Fixed MDIO Bus: probed initcall fixed_mdio_bus_init+0x0/0xd0 returned 0 after 189 usecs calling net_olddevs_init+0x0/0x9e @ 1 initcall net_olddevs_init+0x0/0x9e returned 0 after 3 usecs calling netif_init+0x0/0x6a @ 1 initcall netif_init+0x0/0x6a returned 0 after 0 usecs calling cdrom_init+0x0/0x6a @ 1 initcall cdrom_init+0x0/0x6a returned 0 after 195 usecs calling mon_init+0x0/0x117 @ 1 initcall mon_init+0x0/0x117 returned 0 after 283 usecs calling ehci_hcd_init+0x0/0xc0 @ 1 ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver xen: registering gsi 18 triggering 0 polarity 1 alloc irq_desc for 18 on node 0 alloc kstat_irqs on node 0 xen: --> irq=18 ehci_hcd 0000:00:1a.7: PCI INT C -> GSI 18 (level, low) -> IRQ 18 ehci_hcd 0000:00:1a.7: setting latency timer to 64 ehci_hcd 0000:00:1a.7: EHCI Host Controller ehci_hcd 0000:00:1a.7: new USB bus registered, assigned bus number 1 ehci_hcd 0000:00:1a.7: debug port 1 ehci_hcd 0000:00:1a.7: cache line size of 32 is not supported ehci_hcd 0000:00:1a.7: irq 18, io mem 0xfbbde000 ehci_hcd 0000:00:1a.7: USB 2.0 started, EHCI 1.00 usb usb1: New USB device found, idVendor=1d6b, idProduct=0002 usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1 usb usb1: Product: EHCI Host Controller usb usb1: Manufacturer: Linux 2.6.32.13 ehci_hcd usb usb1: SerialNumber: 0000:00:1a.7 usb usb1: configuration #1 chosen from 1 choice hub 1-0:1.0: USB hub found hub 1-0:1.0: 6 ports detected xen: registering gsi 23 triggering 0 polarity 1 alloc irq_desc for 23 on node 0 alloc kstat_irqs on node 0 xen: --> irq=23 ehci_hcd 0000:00:1d.7: PCI INT A -> GSI 23 (level, low) -> IRQ 23 ehci_hcd 0000:00:1d.7: setting latency timer to 64 ehci_hcd 0000:00:1d.7: EHCI Host Controller ehci_hcd 0000:00:1d.7: new USB bus registered, assigned bus number 2 ehci_hcd 0000:00:1d.7: debug port 1 ehci_hcd 0000:00:1d.7: cache line size of 32 is not supported ehci_hcd 0000:00:1d.7: irq 23, io mem 0xfbbdc000 ehci_hcd 0000:00:1d.7: USB 2.0 started, EHCI 1.00 usb usb2: New USB device found, idVendor=1d6b, idProduct=0002 usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1 usb usb2: Product: EHCI Host Controller usb usb2: Manufacturer: Linux 2.6.32.13 ehci_hcd usb usb2: SerialNumber: 0000:00:1d.7 usb usb2: configuration #1 chosen from 1 choice hub 2-0:1.0: USB hub found hub 2-0:1.0: 6 ports detected initcall ehci_hcd_init+0x0/0xc0 returned 0 after 36306 usecs calling ohci_hcd_mod_init+0x0/0x92 @ 1 ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver initcall ohci_hcd_mod_init+0x0/0x92 returned 0 after 121 usecs calling uhci_hcd_init+0x0/0xc0 @ 1 uhci_hcd: USB Universal Host Controller Interface driver xen: registering gsi 16 triggering 0 polarity 1 xen_allocate_pirq: returning irq 16 for gsi 16 xen: --> irq=16 Already setup the GSI :16 uhci_hcd 0000:00:1a.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16 uhci_hcd 0000:00:1a.0: setting latency timer to 64 uhci_hcd 0000:00:1a.0: UHCI Host Controller uhci_hcd 0000:00:1a.0: new USB bus registered, assigned bus number 3 uhci_hcd 0000:00:1a.0: irq 16, io base 0x0000ac00 usb usb3: New USB device found, idVendor=1d6b, idProduct=0001 usb usb3: New USB device strings: Mfr=3, Product=2, SerialNumber=1 usb usb3: Product: UHCI Host Controller usb usb3: Manufacturer: Linux 2.6.32.13 uhci_hcd usb usb3: SerialNumber: 0000:00:1a.0 usb usb3: configuration #1 chosen from 1 choice hub 3-0:1.0: USB hub found hub 3-0:1.0: 2 ports detected xen: registering gsi 21 triggering 0 polarity 1 alloc irq_desc for 21 on node 0 alloc kstat_irqs on node 0 xen: --> irq=21 uhci_hcd 0000:00:1a.1: PCI INT B -> GSI 21 (level, low) -> IRQ 21 uhci_hcd 0000:00:1a.1: setting latency timer to 64 uhci_hcd 0000:00:1a.1: UHCI Host Controller uhci_hcd 0000:00:1a.1: new USB bus registered, assigned bus number 4 uhci_hcd 0000:00:1a.1: irq 21, io base 0x0000a880 usb usb4: New USB device found, idVendor=1d6b, idProduct=0001 usb usb4: New USB device strings: Mfr=3, Product=2, SerialNumber=1 usb usb4: Product: UHCI Host Controller usb usb4: Manufacturer: Linux 2.6.32.13 uhci_hcd usb usb4: SerialNumber: 0000:00:1a.1 usb usb4: configuration #1 chosen from 1 choice hub 4-0:1.0: USB hub found hub 4-0:1.0: 2 ports detected xen: registering gsi 19 triggering 0 polarity 1 xen_allocate_pirq: returning irq 19 for gsi 19 xen: --> irq=19 Already setup the GSI :19 uhci_hcd 0000:00:1a.2: PCI INT D -> GSI 19 (level, low) -> IRQ 19 uhci_hcd 0000:00:1a.2: setting latency timer to 64 uhci_hcd 0000:00:1a.2: UHCI Host Controller uhci_hcd 0000:00:1a.2: new USB bus registered, assigned bus number 5 uhci_hcd 0000:00:1a.2: irq 19, io base 0x0000a800 usb usb5: New USB device found, idVendor=1d6b, idProduct=0001 usb usb5: New USB device strings: Mfr=3, Product=2, SerialNumber=1 usb usb5: Product: UHCI Host Controller usb usb5: Manufacturer: Linux 2.6.32.13 uhci_hcd usb usb5: SerialNumber: 0000:00:1a.2 usb usb5: configuration #1 chosen from 1 choice hub 5-0:1.0: USB hub found hub 5-0:1.0: 2 ports detected xen: registering gsi 23 triggering 0 polarity 1 xen_allocate_pirq: returning irq 23 for gsi 23 xen: --> irq=23 Already setup the GSI :23 uhci_hcd 0000:00:1d.0: PCI INT A -> GSI 23 (level, low) -> IRQ 23 uhci_hcd 0000:00:1d.0: setting latency timer to 64 uhci_hcd 0000:00:1d.0: UHCI Host Controller uhci_hcd 0000:00:1d.0: new USB bus registered, assigned bus number 6 uhci_hcd 0000:00:1d.0: irq 23, io base 0x0000a480 usb usb6: New USB device found, idVendor=1d6b, idProduct=0001 usb usb6: New USB device strings: Mfr=3, Product=2, SerialNumber=1 usb usb6: Product: UHCI Host Controller usb usb6: Manufacturer: Linux 2.6.32.13 uhci_hcd usb usb6: SerialNumber: 0000:00:1d.0 usb usb6: configuration #1 chosen from 1 choice hub 6-0:1.0: USB hub found hub 6-0:1.0: 2 ports detected xen: registering gsi 19 triggering 0 polarity 1 xen_allocate_pirq: returning irq 19 for gsi 19 xen: --> irq=19 Already setup the GSI :19 uhci_hcd 0000:00:1d.1: PCI INT B -> GSI 19 (level, low) -> IRQ 19 uhci_hcd 0000:00:1d.1: setting latency timer to 64 uhci_hcd 0000:00:1d.1: UHCI Host Controller uhci_hcd 0000:00:1d.1: new USB bus registered, assigned bus number 7 uhci_hcd 0000:00:1d.1: irq 19, io base 0x0000a400 usb usb7: New USB device found, idVendor=1d6b, idProduct=0001 usb usb7: New USB device strings: Mfr=3, Product=2, SerialNumber=1 usb usb7: Product: UHCI Host Controller usb usb7: Manufacturer: Linux 2.6.32.13 uhci_hcd usb usb7: SerialNumber: 0000:00:1d.1 usb usb7: configuration #1 chosen from 1 choice hub 7-0:1.0: USB hub found hub 7-0:1.0: 2 ports detected xen: registering gsi 18 triggering 0 polarity 1 xen_allocate_pirq: returning irq 18 for gsi 18 xen: --> irq=18 Already setup the GSI :18 uhci_hcd 0000:00:1d.2: PCI INT C -> GSI 18 (level, low) -> IRQ 18 uhci_hcd 0000:00:1d.2: setting latency timer to 64 uhci_hcd 0000:00:1d.2: UHCI Host Controller uhci_hcd 0000:00:1d.2: new USB bus registered, assigned bus number 8 uhci_hcd 0000:00:1d.2: irq 18, io base 0x0000a080 usb usb8: New USB device found, idVendor=1d6b, idProduct=0001 usb usb8: New USB device strings: Mfr=3, Product=2, SerialNumber=1 usb usb8: Product: UHCI Host Controller usb usb8: Manufacturer: Linux 2.6.32.13 uhci_hcd usb usb8: SerialNumber: 0000:00:1d.2 usb usb8: configuration #1 chosen from 1 choice hub 8-0:1.0: USB hub found hub 8-0:1.0: 2 ports detected initcall uhci_hcd_init+0x0/0xc0 returned 0 after 27682 usecs calling i8042_init+0x0/0x3a7 @ 1 PNP: No PS/2 controller found. Probing ports directly. serio: i8042 KBD port at 0x60,0x64 irq 1 serio: i8042 AUX port at 0x60,0x64 irq 12 initcall i8042_init+0x0/0x3a7 returned 0 after 3611 usecs calling serport_init+0x0/0x34 @ 1 initcall serport_init+0x0/0x34 returned 0 after 1 usecs calling mousedev_init+0x0/0x62 @ 1 mice: PS/2 mouse device common for all mice initcall mousedev_init+0x0/0x62 returned 0 after 614 usecs calling evdev_init+0x0/0x12 @ 1 initcall evdev_init+0x0/0x12 returned 0 after 447 usecs calling atkbd_init+0x0/0x27 @ 1 initcall atkbd_init+0x0/0x27 returned 0 after 105 usecs calling psmouse_init+0x0/0x74 @ 1 initcall psmouse_init+0x0/0x74 returned 0 after 442 usecs calling xenkbd_init+0x0/0x5d @ 1 initcall xenkbd_init+0x0/0x5d returned -19 after 0 usecs calling cmos_init+0x0/0x6d @ 1 rtc_cmos 00:03: RTC can wake from S4 rtc_cmos 00:03: rtc core: registered rtc_cmos as rtc0 rtc0: alarms up to one month, y3k, 114 bytes nvram initcall cmos_init+0x0/0x6d returned 0 after 619 usecs calling dm_init+0x0/0x49 @ 1 device-mapper: uevent: version 1.0.3 device-mapper: ioctl: 4.15.0-ioctl (2009-04-01) initialised: dm-devel@redhat.com initcall dm_init+0x0/0x49 returned 0 after 1824 usecs calling dm_snapshot_init+0x0/0x26a @ 1 initcall dm_snapshot_init+0x0/0x26a returned 0 after 898 usecs calling dm_mirror_init+0x0/0x79 @ 1 initcall dm_mirror_init+0x0/0x79 returned 0 after 252 usecs calling dm_dirty_log_init+0x0/0x59 @ 1 initcall dm_dirty_log_init+0x0/0x59 returned 0 after 16 usecs calling dm_zero_init+0x0/0x31 @ 1 initcall dm_zero_init+0x0/0x31 returned 0 after 1 usecs calling init_ladder+0x0/0x12 @ 1 cpuidle: using governor ladder initcall init_ladder+0x0/0x12 returned 0 after 19 usecs calling init_menu+0x0/0x12 @ 1 cpuidle: using governor menu initcall init_menu+0x0/0x12 returned 0 after 2 usecs calling efivars_init+0x0/0x213 @ 1 initcall efivars_init+0x0/0x213 returned -19 after 0 usecs calling hid_init+0x0/0x66 @ 1 initcall hid_init+0x0/0x66 returned 0 after 175 usecs calling a4_init+0x0/0x1b @ 1 initcall a4_init+0x0/0x1b returned 0 after 68 usecs calling apple_init+0x0/0x38 @ 1 initcall apple_init+0x0/0x38 returned 0 after 84 usecs calling belkin_init+0x0/0x1b @ 1 initcall belkin_init+0x0/0x1b returned 0 after 65 usecs calling ch_init+0x0/0x1b @ 1 initcall ch_init+0x0/0x1b returned 0 after 59 usecs calling ch_init+0x0/0x1b @ 1 initcall ch_init+0x0/0x1b returned 0 after 69 usecs calling cp_init+0x0/0x1b @ 1 initcall cp_init+0x0/0x1b returned 0 after 65 usecs calling dr_init+0x0/0x1b @ 1 initcall dr_init+0x0/0x1b returned 0 after 56 usecs calling ez_init+0x0/0x1b @ 1 initcall ez_init+0x0/0x1b returned 0 after 57 usecs calling gyration_init+0x0/0x1b @ 1 initcall gyration_init+0x0/0x1b returned 0 after 52 usecs calling ks_init+0x0/0x1b @ 1 initcall ks_init+0x0/0x1b returned 0 after 98 usecs calling kye_init+0x0/0x1b @ 1 initcall kye_init+0x0/0x1b returned 0 after 60 usecs calling lg_init+0x0/0x1b @ 1 initcall lg_init+0x0/0x1b returned 0 after 73 usecs calling ms_init+0x0/0x1b @ 1 initcall ms_init+0x0/0x1b returned 0 after 68 usecs calling mr_init+0x0/0x1b @ 1 initcall mr_init+0x0/0x1b returned 0 after 64 usecs calling ntrig_init+0x0/0x1b @ 1 initcall ntrig_init+0x0/0x1b returned 0 after 72 usecs calling pl_init+0x0/0x1b @ 1 initcall pl_init+0x0/0x1b returned 0 after 64 usecs calling pl_init+0x0/0x1b @ 1 initcall pl_init+0x0/0x1b returned 0 after 71 usecs calling samsung_init+0x0/0x1b @ 1 initcall samsung_init+0x0/0x1b returned 0 after 59 usecs calling sjoy_init+0x0/0x1b @ 1 initcall sjoy_init+0x0/0x1b returned 0 after 64 usecs calling sony_init+0x0/0x1b @ 1 initcall sony_init+0x0/0x1b returned 0 after 70 usecs calling sp_init+0x0/0x1b @ 1 initcall sp_init+0x0/0x1b returned 0 after 57 usecs calling ga_init+0x0/0x1b @ 1 initcall ga_init+0x0/0x1b returned 0 after 52 usecs calling tm_init+0x0/0x1b @ 1 initcall tm_init+0x0/0x1b returned 0 after 52 usecs calling ts_init+0x0/0x1b @ 1 initcall ts_init+0x0/0x1b returned 0 after 57 usecs calling twinhan_init+0x0/0x1b @ 1 initcall twinhan_init+0x0/0x1b returned 0 after 85 usecs calling zp_init+0x0/0x1b @ 1 initcall zp_init+0x0/0x1b returned 0 after 70 usecs calling hid_init+0x0/0xcb @ 1 usbcore: registered new interface driver hiddev usbcore: registered new interface driver usbhid usbhid: v2.6:USB HID core driver initcall hid_init+0x0/0xcb returned 0 after 446 usecs calling flow_cache_init+0x0/0x1b0 @ 1 initcall flow_cache_init+0x0/0x1b0 returned 0 after 350 usecs calling blackhole_module_init+0x0/0x12 @ 1 initcall blackhole_module_init+0x0/0x12 returned 0 after 2 usecs calling init_cgroup_cls+0x0/0x12 @ 1 initcall init_cgroup_cls+0x0/0x12 returned 0 after 21 usecs calling nf_conntrack_standalone_init+0x0/0x12 @ 1 nf_conntrack version 0.5.0 (16384 buckets, 65536 max) CONFIG_NF_CT_ACCT is deprecated and will be removed soon. Please use nf_conntrack.acct=1 kernel parameter, acct=1 nf_conntrack module option or sysctl net.netfilter.nf_conntrack_acct=1 to enable it. initcall nf_conntrack_standalone_init+0x0/0x12 returned 0 after 22301 usecs calling xt_init+0x0/0x190 @ 1 initcall xt_init+0x0/0x190 returned 0 after 42 usecs calling tcpudp_mt_init+0x0/0x17 @ 1 initcall tcpudp_mt_init+0x0/0x17 returned 0 after 25 usecs calling conntrack_mt_init+0x0/0x17 @ 1 initcall conntrack_mt_init+0x0/0x17 returned 0 after 2 usecs calling state_mt_init+0x0/0x17 @ 1 initcall state_mt_init+0x0/0x17 returned 0 after 2 usecs calling sysctl_ipv4_init+0x0/0x4e @ 1 initcall sysctl_ipv4_init+0x0/0x4e returned 0 after 2354 usecs calling init_syncookies+0x0/0x19 @ 1 initcall init_syncookies+0x0/0x19 returned 0 after 44 usecs calling ipv4_netfilter_init+0x0/0x17 @ 1 initcall ipv4_netfilter_init+0x0/0x17 returned 0 after 16 usecs calling nf_conntrack_l3proto_ipv4_init+0x0/0x12d @ 1 initcall nf_conntrack_l3proto_ipv4_init+0x0/0x12d returned 0 after 506 usecs calling nf_defrag_init+0x0/0x17 @ 1 initcall nf_defrag_init+0x0/0x17 returned 0 after 2 usecs calling ip_tables_init+0x0/0xaf @ 1 ip_tables: (C) 2000-2006 Netfilter Core Team initcall ip_tables_init+0x0/0xaf returned 0 after 44 usecs calling iptable_filter_init+0x0/0x6c @ 1 initcall iptable_filter_init+0x0/0x6c returned 0 after 136 usecs calling reject_tg_init+0x0/0x12 @ 1 initcall reject_tg_init+0x0/0x12 returned 0 after 3 usecs calling cubictcp_register+0x0/0x65 @ 1 TCP cubic registered initcall cubictcp_register+0x0/0x65 returned 0 after 3 usecs calling xfrm_user_init+0x0/0x4d @ 1 Initializing XFRM netlink socket initcall xfrm_user_init+0x0/0x4d returned 0 after 49 usecs calling packet_init+0x0/0x47 @ 1 NET: Registered protocol family 17 initcall packet_init+0x0/0x47 returned 0 after 45 usecs calling dsa_init_module+0x0/0x14 @ 1 initcall dsa_init_module+0x0/0x14 returned 0 after 1 usecs calling edsa_init_module+0x0/0x14 @ 1 initcall edsa_init_module+0x0/0x14 returned 0 after 1 usecs calling trailer_init_module+0x0/0x14 @ 1 initcall trailer_init_module+0x0/0x14 returned 0 after 1 usecs calling mv88e6060_init+0x0/0x14 @ 1 initcall mv88e6060_init+0x0/0x14 returned 0 after 14 usecs calling mv88e6123_61_65_init+0x0/0x14 @ 1 initcall mv88e6123_61_65_init+0x0/0x14 returned 0 after 1 usecs calling mv88e6131_init+0x0/0x14 @ 1 initcall mv88e6131_init+0x0/0x14 returned 0 after 1 usecs calling dsa_init_module+0x0/0x12 @ 1 initcall dsa_init_module+0x0/0x12 returned 0 after 73 usecs calling dcbnl_init+0x0/0x32 @ 1 initcall dcbnl_init+0x0/0x32 returned 0 after 0 usecs calling mce_debugfs_init+0x0/0x3b @ 1 initcall mce_debugfs_init+0x0/0x3b returned 0 after 46 usecs calling severities_debugfs_init+0x0/0x3b @ 1 initcall severities_debugfs_init+0x0/0x3b returned 0 after 18 usecs calling hpet_insert_resource+0x0/0x23 @ 1 initcall hpet_insert_resource+0x0/0x23 returned 0 after 3 usecs calling update_mp_table+0x0/0x689 @ 1 initcall update_mp_table+0x0/0x689 returned 0 after 0 usecs calling lapic_insert_resource+0x0/0x40 @ 1 initcall lapic_insert_resource+0x0/0x40 returned -1 after 0 usecs initcall lapic_insert_resource+0x0/0x40 returned with error code -1 calling init_lapic_nmi_sysfs+0x0/0x39 @ 1 initcall init_lapic_nmi_sysfs+0x0/0x39 returned 0 after 0 usecs calling io_apic_bug_finalize+0x0/0x1b @ 1 initcall io_apic_bug_finalize+0x0/0x1b returned 0 after 0 usecs calling check_early_ioremap_leak+0x0/0x67 @ 1 initcall check_early_ioremap_leak+0x0/0x67 returned 0 after 0 usecs calling pat_memtype_list_init+0x0/0x29 @ 1 initcall pat_memtype_list_init+0x0/0x29 returned 0 after 19 usecs calling sched_init_debug+0x0/0x24 @ 1 initcall sched_init_debug+0x0/0x24 returned 0 after 18 usecs calling init_oops_id+0x0/0x36 @ 1 initcall init_oops_id+0x0/0x36 returned 0 after 8 usecs calling disable_boot_consoles+0x0/0x5c @ 1 initcall disable_boot_consoles+0x0/0x5c returned 0 after 0 usecs calling pm_qos_power_init+0x0/0xca @ 1 initcall pm_qos_power_init+0x0/0xca returned 0 after 352 usecs calling test_suspend+0x0/0x19d @ 1 initcall test_suspend+0x0/0x19d returned 0 after 0 usecs calling software_resume+0x0/0x20f @ 1 PM: Resume from disk failed. initcall software_resume+0x0/0x20f returned -2 after 15 usecs initcall software_resume+0x0/0x20f returned with error code -2 calling debugfs_kprobe_init+0x0/0x8e @ 1 initcall debugfs_kprobe_init+0x0/0x8e returned 0 after 111 usecs calling taskstats_init+0x0/0x95 @ 1 registered taskstats version 1 initcall taskstats_init+0x0/0x95 returned 0 after 35 usecs calling clear_boot_tracer+0x0/0x2d @ 1 initcall clear_boot_tracer+0x0/0x2d returned 0 after 0 usecs calling fail_page_alloc_debugfs+0x0/0xe4 @ 1 initcall fail_page_alloc_debugfs+0x0/0xe4 returned 0 after 193 usecs calling max_swapfiles_check+0x0/0x8 @ 1 initcall max_swapfiles_check+0x0/0x8 returned 0 after 0 usecs calling failslab_debugfs_init+0x0/0x6b @ 1 initcall failslab_debugfs_init+0x0/0x6b returned 0 after 135 usecs calling init_ima+0x0/0x1a @ 1 No TPM chip found, activating TPM-bypass! initcall init_ima+0x0/0x1a returned 0 after 615 usecs calling fail_make_request_debugfs+0x0/0x19 @ 1 initcall fail_make_request_debugfs+0x0/0x19 returned 0 after 306 usecs calling random32_reseed+0x0/0xa9 @ 1 initcall random32_reseed+0x0/0xa9 returned 0 after 147 usecs calling pci_resource_alignment_sysfs_init+0x0/0x19 @ 1 initcall pci_resource_alignment_sysfs_init+0x0/0x19 returned 0 after 6 usecs calling pci_sysfs_init+0x0/0x4c @ 1 initcall pci_sysfs_init+0x0/0x4c returned 0 after 3427 usecs calling boot_wait_for_devices+0x0/0x19 @ 1 initcall boot_wait_for_devices+0x0/0x19 returned 0 after 1 usecs calling regulator_init_complete+0x0/0x14b @ 1 initcall regulator_init_complete+0x0/0x14b returned 0 after 16 usecs calling seqgen_init+0x0/0xf @ 1 initcall seqgen_init+0x0/0xf returned 0 after 46 usecs calling late_resume_init+0x0/0x124 @ 1 Magic number: 10:134:278 tty tty15: hash matches initcall late_resume_init+0x0/0x124 returned 0 after 92 usecs calling scsi_complete_async_scans+0x0/0x148 @ 1 initcall scsi_complete_async_scans+0x0/0x148 returned 0 after 0 usecs calling rtc_hctosys+0x0/0x152 @ 1 usb 2-1: new high speed USB device using ehci_hcd and address 2 usb 2-1: New USB device found, idVendor=2001, idProduct=f103 usb 2-1: New USB device strings: Mfr=0, Product=0, SerialNumber=0 usb 2-1: configuration #1 chosen from 1 choice hub 2-1:1.0: USB hub found hub 2-1:1.0: 7 ports detected usb 2-1.2: new full speed USB device using ehci_hcd and address 4 usb 2-1.2: New USB device found, idVendor=04e8, idProduct=326c usb 2-1.2: New USB device strings: Mfr=1, Product=2, SerialNumber=3 usb 2-1.2: Product: Samsung ML-2010 usb 2-1.2: Manufacturer: Samsung usb 2-1.2: SerialNumber: 3A61BKCL919879R. usb 2-1.2: configuration #1 chosen from 1 choice usb 6-2: new low speed USB device using uhci_hcd and address 2 usb 6-2: New USB device found, idVendor=05af, idProduct=0408 usb 6-2: New USB device strings: Mfr=0, Product=2, SerialNumber=0 usb 6-2: Product: 2.4G USB RF KeyBoard usb 6-2: configuration #1 chosen from 1 choice input: 2.4G USB RF KeyBoard as /devices/pci0000:00/0000:00:1d.0/usb6/6-2/6-2:1.0/input/input3 generic-usb 0003:05AF:0408.0001: input,hidraw0: USB HID v1.10 Keyboard [2.4G USB RF KeyBoard] on usb-0000:00:1d.0-2/input0 input: 2.4G USB RF KeyBoard as /devices/pci0000:00/0000:00:1d.0/usb6/6-2/6-2:1.1/input/input4 generic-usb 0003:05AF:0408.0002: input,hidraw1: USB HID v1.10 Mouse [2.4G USB RF KeyBoard] on usb-0000:00:1d.0-2/input1 input: 2.4G USB RF KeyBoard as /devices/pci0000:00/0000:00:1d.0/usb6/6-2/6-2:1.2/input/input5 rtc_cmos 00:03: setting system clock to 2010-05-30 11:17:51 UTC (1275218271) initcall rtc_hctosys+0x0/0x152 returned 0 after 1682629 usecs calling memmap_init+0x0/0xa3 @ 1 calling 3_async_port_probe+0x0/0xc9 @ 261 generic-usb 0003:05AF:0408.0003: input,hiddev96,hidraw2: USB HID v1.10 Device [2.4G USB RF KeyBoard] on usb-0000:00:1d.0-2/input2 initcall memmap_init+0x0/0xa3 returned 0 after 811 usecs calling pci_mmcfg_late_insert_resources+0x0/0x163 @ 1 initcall pci_mmcfg_late_insert_resources+0x0/0x163 returned 0 after 8 usecs calling init_net_drop_monitor+0x0/0x17e @ 1 Initalizing network drop monitor service initcall init_net_drop_monitor+0x0/0x17e returned 0 after 290 usecs calling tcp_congestion_default+0x0/0x12 @ 1 initcall tcp_congestion_default+0x0/0x12 returned 0 after 1 usecs calling initialize_hashrnd+0x0/0x19 @ 1 initcall initialize_hashrnd+0x0/0x19 returned 0 after 7 usecs async_waiting @ 1 async_waiting @ 261 calling 4_async_port_probe+0x0/0xc9 @ 262 calling 5_async_port_probe+0x0/0xc9 @ 263 async_waiting @ 263 calling 6_async_port_probe+0x0/0xc9 @ 264 async_waiting @ 264 calling 7_async_port_probe+0x0/0xc9 @ 265 async_waiting @ 265 async_waiting @ 262 ata1: SATA link down (SStatus 0 SControl 300) async_waiting @ 233 async_continuing @ 233 after 3 usec initcall 2_async_port_probe+0x0/0xc9 returned 0 after 313154 usecs async_continuing @ 261 after 236544 usec ata2: SATA link down (SStatus 0 SControl 300) async_waiting @ 261 async_continuing @ 261 after 1 usec initcall 3_async_port_probe+0x0/0xc9 returned 0 after 555507 usecs async_continuing @ 262 after 536879 usec ata3: SATA link up 3.0 Gbps (SStatus 123 SControl 300) ata3.00: ATA-8: WDC WD7501AALS-00J7B1, 05.00K05, max UDMA/133 ata3.00: 1465149168 sectors, multi 0: LBA48 NCQ (depth 31/32), AA ata3.00: configured for UDMA/133 async_waiting @ 262 async_continuing @ 262 after 1 usec scsi 2:0:0:0: Direct-Access ATA WDC WD7501AALS-0 05.0 PQ: 0 ANSI: 5 calling 8_sd_probe_async+0x0/0x1e3 @ 261 sd 2:0:0:0: Attached scsi generic sg0 type 0 initcall 4_async_port_probe+0x0/0xc9 returned 0 after 1292146 usecs async_continuing @ 263 after 1312855 usec sd 2:0:0:0: [sda] 1465149168 512-byte logical blocks: (750 GB/698 GiB) sd 2:0:0:0: [sda] Write Protect is off sd 2:0:0:0: [sda] Mode Sense: 00 3a 00 00 sd 2:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA sda: sda1 sda2 sda3 sd 2:0:0:0: [sda] Attached SCSI disk initcall 8_sd_probe_async+0x0/0x1e3 returned 0 after 38221 usecs ata4: SATA link up 1.5 Gbps (SStatus 113 SControl 300) ata4.00: ATAPI: HL-DT-STDVD-RAM GH22NS30, 1.01, max UDMA/100 ata4.00: configured for UDMA/100 async_waiting @ 263 async_continuing @ 263 after 2 usec scsi 3:0:0:0: CD-ROM HL-DT-ST DVD-RAM GH22NS30 1.01 PQ: 0 ANSI: 5 sr0: scsi3-mmc drive: 48x/48x writer dvd-ram cd/rw xa/form2 cdda tray Uniform CD-ROM driver Revision: 3.20 sr 3:0:0:0: Attached scsi CD-ROM sr0 sr 3:0:0:0: Attached scsi generic sg1 type 5 initcall 5_async_port_probe+0x0/0xc9 returned 0 after 2200976 usecs async_continuing @ 264 after 2206705 usec async/2 used greatest stack depth: 4248 bytes left ata5: SATA link down (SStatus 0 SControl 300) async_waiting @ 264 async_continuing @ 264 after 1 usec initcall 6_async_port_probe+0x0/0xc9 returned 0 after 2523975 usecs async_continuing @ 265 after 2529786 usec ata6: SATA link down (SStatus 0 SControl 300) async_waiting @ 265 async_continuing @ 265 after 1 usec initcall 7_async_port_probe+0x0/0xc9 returned 0 after 2847040 usecs async_continuing @ 1 after 2919764 usec Freeing unused kernel memory: 3380k freed Write protecting the kernel read-only data: 7004k mLoading, please wait... calling i2c_init+0x0/0x70 [i2c_core] @ 297 initcall i2c_init+0x0/0x70 [i2c_core] returned 0 after 220 usecs calling nvidiafb_init+0x0/0x25 [nvidiafb] @ 297 nvidiafb 0000:01:00.0: enabling device (0140 -> 0143) xen: registering gsi 16 triggering 0 polarity 1 xen_allocate_pirq: returning irq 16 for gsi 16 xen: --> irq=16 Already setup the GSI :16 nvidiafb 0000:01:00.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16 nvidiafb: Device ID: 10de042f nvidiafb: unknown NV_ARCH xen: registering gsi 16 triggering 0 polarity 1 xen_allocate_pirq: returning irq 16 for gsi 16 xen: --> irq=16 Already setup the GSI :16 nvidiafb 0000:03:00.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16 nvidiafb: Device ID: 10de06fd nvidiafb: unknown NV_ARCH initcall nvidiafb_init+0x0/0x25 [nvidiafb] returned 0 after 67706 usecs calling megasas_init+0x0/0x16f [megaraid_sas] @ 666 megasas: 00.00.04.01 Thu July 24 11:41:51 PST 2008 megasas: 0x1028:0x0015:0x1028:0x1f03: bus 5:slot 14:func 0 xen: registering gsi 18 triggering 0 polarity 1 xen_allocate_pirq: returning irq 18 for gsi 18 xen: --> irq=18 Already setup the GSI :18 megaraid_sas 0000:05:0e.0: PCI INT A -> GSI 18 (level, low) -> IRQ 18 megasas: FW now in Ready state calling e1000_init_module+0x0/0(XEN) [VT-D]iommu.c:821: iommu_fault_status: Primary Pending Fault x70 [e1000e] @ 6(XEN) [VT-D]iommu.c:796: DMAR:[DMA Write] Request device [05:08.0] fault addr 2d0842000, iommu reg = ffff82c3fff57000 (XEN) DMAR:[fault reason 02h] Present bit in context entry is clear 76 (XEN) print_vtd_entries: iommu = ffff83013ff7b130 bdf = 5:8.0 gmfn 2d0842 scsi6 : LSI SAS (XEN) root_entry = ffff83013ff37000 based MegaRAID d(XEN) root_entry[5] = 13cf13001 river (XEN) context = ffff83013cf13000 initcall megasas(XEN) context[40] = 0_0 _init+0x0/0x16f (XEN) ctxt_entry[40] not present [megaraid_sas] r(XEN) [VT-D]iommu.c:821: iommu_fault_status: Primary Pending Fault eturned 0 after (XEN) [VT-D]iommu.c:796: DMAR:[DMA Write] Request device [05:08.0] fault addr 2d0842000, iommu reg = ffff82c3fff57000 (XEN) DMAR:[fault reason 02h] Present bit in context entry is clear 73201 usecs (XEN) print_vtd_entries: iommu = ffff83013ff7b130 bdf = 5:8.0 gmfn 2d0842 scsi scan: INQUI(XEN) root_entry = ffff83013ff37000 RY result too sh(XEN) root_entry[5] = 13cf13001 ort (5), using 3(XEN) context = ffff83013cf13000 6 (XEN) context[40] = 0_0 scsi 6:0:0:0: Di(XEN) ctxt_entry[40] not present rect-Access PQ: 0 ANSI: 0 scsi scan: INQUIRY result too short (5), using 36 scsi 6:0:1:0: Direct-Access PQ: 0 ANSI: 0 scsi scan: INQUIRY result too short (5), using 36 scsi 6:0:2:0: Direct-Access PQ: 0 ANSI: 0 scsi scan: INQUIRY result too short (5), using 36 scsi 6:0:3:0: Direct-Access PQ: 0 ANSI: 0 scsi 6:2:0:0: Direct-Access DELL PERC 5/i 1.03 PQ: 0 ANSI: 5 e1000e: Intel(R) PRO/1000 Network Driver - 1.0.2-k2 e1000e: Copyright (c) 1999-2008 Intel Corporation. e1000e 0000:07:00.0: Disabling L1 ASPM xen: registering gsi 16 triggering 0 polarity 1 xen_allocate_pirq: returning irq 16 for gsi 16 xen: --> irq=16 Already setup the GSI :16 e1000e 0000:07:00.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16 e1000e 0000:07:00.0: setting latency timer to 64 alloc irq_desc for 4260 on node 0 alloc kstat_irqs on node 0 alloc irq_desc for 4259 on node 0 alloc kstat_irqs on node 0 alloc irq_desc for 4258 on node 0 sd 6:2:0:0: Attached scsi generic sg2 type 0 scsi_scan_6 used(XEN) [VT-D]iommu.c:821: iommu_fault_status: Primary Pending Fault greatest stack (XEN) [VT-D]iommu.c:796: DMAR:[DMA Write] Request device [05:08.0] fault addr 2cfa6e000, iommu reg = ffff82c3fff57000 (XEN) DMAR:[fault reason 02h] Present bit in context entry is clear depth: 4088 byte(XEN) print_vtd_entries: iommu = ffff83013ff7b130 bdf 5:8.0 gmfn = 2cfa6e s left (XEN) root_entry = ffff83013ff37000 sd 6:2:0:0: [sdb(XEN) root_entry[5] = 13cf13001 ] 211550208 512-(XEN) context = ffff83013cf13000 byte logical blo(XEN) context[40] = 0_0 cks: (108 GB/100(XEN) ctxt_entry[40] not present GiB) sd 6:2:0:0: [sdb] Write Protect is off sd 6:2:0:0: [sdb] Mode Sense: 1f 00 00 08 sd 6:2:0:0: [sdb] Write cache: disabled, read cache: enabled, doesn't support DPO or FUA sdb: unknown partition table alloc kstat_irqs on node 0 sd 6:2:0:0: [sdb] Attached SCSI disk 0000:07:00.0: eth0: (PCI Express:2.5GB/s:Width x1) 00:30:48:b8:de:18 0000:07:00.0: eth0: Intel(R) PRO/1000 Network Connection 0000:07:00.0: eth0: MAC: 3, PHY: 8, PBA No: 0101ff-0ff e1000e 0000:08:00.0: Disabling L1 ASPM xen: registering gsi 17 triggering 0 polarity 1 xen_allocate_pirq: returning irq 17 for gsi 17 xen: --> irq=17 Already setup the GSI :17 e1000e 0000:08:00.0: PCI INT A -> GSI 17 (level, low) -> IRQ 17 e1000e 0000:08:00.0: setting latency timer to 64 alloc irq_desc for 4257 on node 0 alloc kstat_irqs on node 0 alloc irq_desc for 4256 on node 0 alloc kstat_irqs on node 0 alloc irq_desc for 4255 on node 0 alloc kstat_irqs on node 0 scsi_id used greatest stack depth: 3904 bytes left 0000:08:00.0: eth1: (PCI Express:2.5GB/s:Width x1) 00:30:48:b8:de:19 0000:08:00.0: eth1: Intel(R) PRO/1000 Network Connection 0000:08:00.0: eth1: MAC: 3, PHY: 8, PBA No: 0101ff-0ff initcall e1000_init_module+0x0/0x70 [e1000e] returned 0 after 392599 usecs (XEN) [VT-D]iommu.c:821: iommu_fault_status: Primary Pending Fault (XEN) [VT-D]iommu.c:796: DMAR:[DMA Write] Request device [05:08.0] fault addr 2cede1000, iommu reg = ffff82c3fff57000 (XEN) DMAR:[fault reason 02h] Present bit in context entry is clear (XEN) print_vtd_entries: iommu = ffff83013ff7b130 bdf = 5:8.0 gmfn 2cede1 (XEN) root_entry = ffff83013ff37000 (XEN) root_entry[5] = 13cf13001 (XEN) context = ffff83013cf13000 (XEN) context[40] = 0_0 (XEN) ctxt_entry[40] not present (XEN) [VT-D]iommu.c:821: iommu_fault_status: Primary Pending Fault (XEN) [VT-D]iommu.c:796: DMAR:[DMA Write] Request device [05:08.0] fault addr 2cede3000, iommu reg = ffff82c3fff57000 (XEN) DMAR:[fault reason 02h] Present bit in context entry is clear (XEN) print_vtd_entries: iommu = ffff83013ff7b130 bdf = 5:8.0 gmfn 2cede3 (XEN) root_entry = ffff83013ff37000 (XEN) root_entry[5] = 13cf13001 (XEN) context = ffff83013cf13000 (XEN) context[40] = 0_0 (XEN) ctxt_entry[40] not present (XEN) [VT-D]iommu.c:821: iommu_fault_status: Primary Pending Fault (XEN) [VT-D]iommu.c:796: DMAR:[DMA Write] Request device [05:08.0] fault addr 2cede2000, iommu reg = ffff82c3fff57000 (XEN) DMAR:[fault reason 02h] Present bit in context entry is clear (XEN) print_vtd_entries: iommu = ffff83013ff7b130 bdf = 5:8.0 gmfn 2cede2 (XEN) root_entry = ffff83013ff37000 (XEN) root_entry[5] = 13cf13001 (XEN) context = ffff83013cf13000 (XEN) context[40] = 0_0 (XEN) ctxt_entry[40] not present (XEN) [VT-D]iommu.c:821: iommu_fault_status: Primary Pending Fault (XEN) [VT-D]iommu.c:796: DMAR:[DMA Write] Request device [05:08.0] fault addr 2cfff9000, iommu reg = ffff82c3fff57000 (XEN) DMAR:[fault reason 02h] Present bit in context entry is clear (XEN) print_vtd_entries: iommu = ffff83013ff7b130 bdf = 5:8.0 gmfn 2cfff9 (XEN) root_entry = ffff83013ff37000 (XEN) root_entry[5] = 13cf13001 (XEN) context = ffff83013cf13000 (XEN) context[40] = 0_0 (XEN) ctxt_entry[40] not present (XEN) [VT-D]iommu.c:821: iommu_fault_status: Primary Pending Fault (XEN) [VT-D]iommu.c:796: DMAR:[DMA Write] Request device [05:08.0] fault addr 2ced30000, iommu reg = ffff82c3fff57000 (XEN) DMAR:[fault reason 02h] Present bit in context entry is clear (XEN) print_vtd_entries: iommu = ffff83013ff7b130 bdf = 5:8.0 gmfn 2ced30 (XEN) root_entry = ffff83013ff37000 (XEN) root_entry[5] = 13cf13001 (XEN) context = ffff83013cf13000 (XEN) context[40] = 0_0 (XEN) ctxt_entry[40] not present calling wait_scan_init+0x0/0x12 [scsi_wait_scan] @ 1132 initcall wait_scan_init+0x0/0x12 [scsi_wait_scan] returned 0 after 3 usecs (XEN) [VT-D]iommu.c:821: iommu_fault_status: Primary Pending Fault (XEN) [VT-D]iommu.c:796: DMAR:[DMA Write] Request device [05:08.0] fault addr 2cf14b000, iommu reg = ffff82c3fff57000 (XEN) DMAR:[fault reason 02h] Present bit in context entry is clear (XEN) print_vtd_entries: iommu = ffff83013ff7b130 bdf = 5:8.0 gmfn 2cf14b (XEN) root_entry = ffff83013ff37000 (XEN) root_entry[5] = 13cf13001 (XEN) context = ffff83013cf13000 (XEN) context[40] = 0_0 (XEN) ctxt_entry[40] not present On Sat, 2010-05-29 at 18:20 +0300, Pasi Kärkkäinen wrote:> On Sat, May 29, 2010 at 07:31:17AM -0700, M. Nunberg wrote: > > I've been trying to get VT-D working wiht xen for quite some time, since > > 3.4.2, and I've always had issues with my RAID controller not working > > properly when iommu is not disabled in Xen: > > > > lspci outpuut for the card: > > <snip> > > > > > I am using a Supermicro X8DALi motherboard with a 5500 chipset. > > > > Whenever I try to access the device the Xen console spits out something > > like this: > > (XEN) [VT-D]iommu.c:796: DMAR:[DMA Write] Request device [05:08.0] fault > > addr 204865000, iommu reg = ffff82c3fff57000 > > (XEN) DMAR:[fault reason 02h] Present bit in context entry is clear > > (XEN) print_vtd_entries: iommu = ffff83013fffaee0 bdf = 5:8.0 gmfn > > 204865 > > (XEN) root_entry = ffff83013ff37000 > > (XEN) root_entry[5] = 13cf12001 > > (XEN) context = ffff83013cf12000 > > (XEN) context[40] = 0_0 > > (XEN) ctxt_entry[40] not present > > (XEN) [VT-D]iommu.c:821: iommu_fault_status: Primary Pending Fault > > > > reads are partially succcessful, but I am getting seek errors at times, > > filesystems will mount properly but I cannot use any of them properly.. > > > > > > The actual kernel output varies, sometimes i get EINVAL when I try to > > read from the filesystem, sometimes it simply refuses to at all > > recognize the disk altogether, and other times it will hang the entire > > system, including the hypervisor itself. > > I've tried booting the hypervisor with x2apic disabled, but to no > > effect. I've also tried with the latest xen-4.0-testing (4.0.1), buut > > same issue and same outpuut > > > > A quick google turns up a thread, from this mailing list, with a > > different RAID card, but the kernel output is similar.. e.g. > > > > scsi scan: INQUIRY result too short (5), using 36 > > > > http://lists.xensource.com/archives/html/xen-users/2010-04/msg00535.html > > > > The full xen log is below > > > > Did you use the latest pvops dom0 kernel from xen/stable-2.6.32.x branch? > Could you also post the full serial log _with_ the dom0 kernel messages? > > .. since the problem gets triggered by the dom0 kernel.. > > -- Pasi > > > > > > > > L __ __ _ _ ___ > > ___ > > \ \/ /___ _ __ | || | / _ \ / _ \ 0x146000>, shtab=0x3a2078, > > entry=0x100000 > > \ // _ \ '_ \ | || |_| | | | | | > > | > > / \ __/ | | | |__ _| |_| | |_| |apper/OS-root ro nomodeset > > console=tty0 r > > /_/\_\___|_| |_| | > > _|(_)___(_)___/ > > 020 > > bytes] > > (XEN) Xen version 4.0.0 (mordy@) (gcc version 4.3.2 (Debian 4.3.2-1.1) ) > > Fri May 21 07:50:16 PDT 2010boot-module > > @ > > (XEN) Latest ChangeSet: > > unavailable > > (XEN) Console output is > > synchronous. > > (XEN) Command line: iommu=verbose loglvl=all guest_loglvl=all > > sync_console console_to_rint com1=115200,8n1 > > console=com1 > > (XEN) Video > > information: > > (XEN) VGA is text mode 80x25, font > > 8x16 > > (XEN) VBE/DDC methods: none; EDID transfer time: 0 > > seconds > > (XEN) EDID info not retrieved because no DDC retrieval method > > detected > > (XEN) Disc information: > > (XEN) Found 1 MBR signatures > > (XEN) Found 1 EDD information structures > > (XEN) Xen-e820 RAM map: > > (XEN) 0000000000000000 - 000000000009a000 (usable) > > (XEN) 000000000009a000 - 00000000000a0000 (reserved) > > (XEN) 00000000000e0000 - 0000000000100000 (reserved) > > (XEN) 0000000000100000 - 00000000bf760000 (usable) > > (XEN) 00000000bf76e000 - 00000000bf770000 type 9 > > (XEN) 00000000bf770000 - 00000000bf77e000 (ACPI data) > > (XEN) 00000000bf77e000 - 00000000bf7d0000 (ACPI NVS) > > (XEN) 00000000bf7d0000 - 00000000bf7e0000 (reserved) > > (XEN) 00000000bf7ec000 - 00000000c0000000 (reserved) > > (XEN) 00000000fee00000 - 00000000fee01000 (reserved) > > (XEN) 00000000ffc00000 - 0000000100000000 (reserved) > > (XEN) 0000000100000000 - 0000000340000000 (usable) > > (XEN) ACPI: RSDP 000F9E10, 0024 (r2 ACPIAM) > > (XEN) ACPI: XSDT BF770100, 0094 (r1 NEC 20090424 MSFT > > 97) > > (XEN) ACPI: FACP BF770290, 00F4 (r4 042409 FACP1917 20090424 MSFT > > 97) > > (XEN) ACPI: DSDT BF770670, 5BFB (r2 10601 10601000 0 INTL > > 20051117) > > (XEN) ACPI: FACS BF77E000, 0040 > > (XEN) ACPI: APIC BF770390, 00D2 (r2 042409 APIC1917 20090424 MSFT > > 97) > > (XEN) ACPI: MCFG BF770470, 003C (r1 042409 OEMMCFG 20090424 MSFT > > 97) > > (XEN) ACPI: SLIC BF7704B0, 0176 (r1 NEC 20090424 MSFT > > 97) > > (XEN) ACPI: ERST BF770630, 0040 (r1 042409 WHEA1917 20090424 MSFT > > 97) > > (XEN) ACPI: OEMB BF77E040, 007B (r1 042409 OEMB1917 20090424 MSFT > > 97) > > (XEN) ACPI: SRAT BF77A670, 01D0 (r1 042409 OEMSRAT 1 INTL > > 1) > > (XEN) ACPI: HPET BF77A840, 0038 (r1 042409 OEMHPET 20090424 MSFT > > 97) > > (XEN) ACPI: DMAR BF77E0C0, 0118 (r1 AMI OEMDMAR 1 MSFT > > 97) > > (XEN) ACPI: SSDT BF781DF0, 0363 (r1 DpgPmm CpuPm 12 INTL > > 20051117) > > (XEN) ACPI: EINJ BF77A880, 0130 (r1 AMIER AMI_EINJ 20090424 MSFT > > 97) > > (XEN) ACPI: BERT BF77AA10, 0030 (r1 AMIER AMI_BERT 20090424 MSFT > > 97) > > (XEN) ACPI: ERST BF77AA40, 01B0 (r1 AMIER AMI_ERST 20090424 MSFT > > 97) > > (XEN) ACPI: HEST BF77ABF0, 00A8 (r1 AMIER AMI_HEST 20090424 MSFT > > 97) > > (XEN) System RAM: 12045MB (12334808kB) > > (XEN) SRAT: PXM 0 -> APIC 0 -> Node 0 > > (XEN) SRAT: PXM 0 -> APIC 2 -> Node 0 > > (XEN) SRAT: PXM 0 -> APIC 4 -> Node 0 > > (XEN) SRAT: PXM 0 -> APIC 6 -> Node 0 > > (XEN) SRAT: PXM 0 -> APIC 1 -> Node 0 > > (XEN) SRAT: PXM 0 -> APIC 3 -> Node 0 > > (XEN) SRAT: PXM 0 -> APIC 5 -> Node 0 > > (XEN) SRAT: PXM 0 -> APIC 7 -> Node 0 > > (XEN) SRAT: PXM 1 -> APIC 16 -> Node 1 > > (XEN) SRAT: PXM 1 -> APIC 18 -> Node 1 > > (XEN) SRAT: PXM 1 -> APIC 20 -> Node 1 > > (XEN) SRAT: PXM 1 -> APIC 22 -> Node 1 > > (XEN) SRAT: PXM 1 -> APIC 17 -> Node 1 > > (XEN) SRAT: PXM 1 -> APIC 19 -> Node 1 > > (XEN) SRAT: PXM 1 -> APIC 21 -> Node 1 > > (XEN) SRAT: PXM 1 -> APIC 23 -> Node 1 > > (XEN) SRAT: Node 0 PXM 0 0-a0000 > > (XEN) SRAT: Node 0 PXM 0 100000-c0000000 > > (XEN) SRAT: Node 0 PXM 0 100000000-1c0000000 > > (XEN) SRAT: Node 1 PXM 1 1c0000000-340000000 > > (XEN) NUMA: Allocated memnodemap from 33fdfb000 - 33fdff000 > > (XEN) NUMA: Using 8 for the hash shift. > > (XEN) Domain heap initialised DMA width 30 bits > > (XEN) found SMP MP-table at 000ff780 > > (XEN) DMI present. > > (XEN) Using APIC driver default > > (XEN) ACPI: PM-Timer IO Port: 0x808 > > (XEN) ACPI: ACPI SLEEP INFO: pm1x_cnt[804,0], pm1x_evt[800,0] > > (XEN) ACPI: wakeup_vec[bf77e00c], vec_size[20] > > (XEN) ACPI: Local APIC address 0xfee00000 > > (XEN) ACPI: LAPIC (acpi_id[0x01] lapic_id[0x00] enabled) > > (XEN) Processor #0 7:10 APIC version 21 > > (XEN) ACPI: LAPIC (acpi_id[0x02] lapic_id[0x10] enabled) > > (XEN) Processor #16 7:10 APIC version 21 > > (XEN) ACPI: LAPIC (acpi_id[0x03] lapic_id[0x02] enabled) > > (XEN) Processor #2 7:10 APIC version 21 > > (XEN) ACPI: LAPIC (acpi_id[0x04] lapic_id[0x12] enabled) > > (XEN) Processor #18 7:10 APIC version 21 > > (XEN) ACPI: LAPIC (acpi_id[0x05] lapic_id[0x04] enabled) > > (XEN) Processor #4 7:10 APIC version 21 > > (XEN) ACPI: LAPIC (acpi_id[0x06] lapic_id[0x14] enabled) > > (XEN) Processor #20 7:10 APIC version 21 > > (XEN) ACPI: LAPIC (acpi_id[0x07] lapic_id[0x06] enabled) > > (XEN) Processor #6 7:10 APIC version 21 > > (XEN) ACPI: LAPIC (acpi_id[0x08] lapic_id[0x16] enabled) > > (XEN) Processor #22 7:10 APIC version 21 > > (XEN) ACPI: LAPIC (acpi_id[0x09] lapic_id[0x01] enabled) > > (XEN) Processor #1 7:10 APIC version 21 > > (XEN) ACPI: LAPIC (acpi_id[0x0a] lapic_id[0x11] enabled) > > (XEN) Processor #17 7:10 APIC version 21 > > (XEN) ACPI: LAPIC (acpi_id[0x0b] lapic_id[0x03] enabled) > > (XEN) Processor #3 7:10 APIC version 21 > > (XEN) ACPI: LAPIC (acpi_id[0x0c] lapic_id[0x13] enabled) > > (XEN) Processor #19 7:10 APIC version 21 > > (XEN) ACPI: LAPIC (acpi_id[0x0d] lapic_id[0x05] enabled) > > (XEN) Processor #5 7:10 APIC version 21 > > (XEN) ACPI: LAPIC (acpi_id[0x0e] lapic_id[0x15] enabled) > > (XEN) Processor #21 7:10 APIC version 21 > > (XEN) ACPI: LAPIC (acpi_id[0x0f] lapic_id[0x07] enabled) > > (XEN) Processor #7 7:10 APIC version 21 > > (XEN) ACPI: LAPIC (acpi_id[0x10] lapic_id[0x17] enabled) > > (XEN) Processor #23 7:10 APIC version 21 > > (XEN) ACPI: LAPIC_NMI (acpi_id[0xff] dfl dfl lint[0x1]) > > (XEN) Overriding APIC driver with bigsmp > > (XEN) ACPI: IOAPIC (id[0x08] address[0xfec00000] gsi_base[0]) > > (XEN) IOAPIC[0]: apic_id 8, version 32, address 0xfec00000, GSI 0-23 > > (XEN) ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl) > > (XEN) ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 20 low level) > > (XEN) ACPI: IRQ0 used by override. > > (XEN) ACPI: IRQ2 used by override. > > (XEN) ACPI: IRQ9 used by override. > > (XEN) Enabling APIC mode: Phys. Using 1 I/O APICs > > (XEN) ACPI: HPET id: 0xffffffff base: 0xfed00000 > > (XEN) [VT-D]dmar.c:679: Host address width 40 > > (XEN) [VT-D]dmar.c:694: found ACPI_DMAR_DRHD: > > (XEN) [VT-D]dmar.c:398: dmaru->address = fbffe000 > > (XEN) [VT-D]dmar.c:340: IOAPIC: f0:1f.7 > > (XEN) [VT-D]dmar.c:411: flags: INCLUDE_ALL > > (XEN) [VT-D]dmar.c:699: found ACPI_DMAR_RMRR: > > (XEN) [VT-D]dmar.c:334: endpoint: 0:1d.0 > > (XEN) [VT-D]dmar.c:334: endpoint: 0:1d.1 > > (XEN) [VT-D]dmar.c:334: endpoint: 0:1d.2 > > (XEN) [VT-D]dmar.c:334: endpoint: 0:1d.7 > > (XEN) [VT-D]dmar.c:334: endpoint: 0:1a.0 > > (XEN) [VT-D]dmar.c:334: endpoint: 0:1a.1 > > (XEN) [VT-D]dmar.c:334: endpoint: 0:1a.2 > > (XEN) [VT-D]dmar.c:334: endpoint: 0:1a.7 > > (XEN) [VT-D]dmar.c:571: RMRR region: base_addr ec000 end_address effff > > (XEN) [VT-D]dmar.c:699: found ACPI_DMAR_RMRR: > > (XEN) [VT-D]dmar.c:334: endpoint: 0:1d.0 > > (XEN) [VT-D]dmar.c:334: endpoint: 0:1d.1 > > (XEN) [VT-D]dmar.c:334: endpoint: 0:1d.2 > > (XEN) [VT-D]dmar.c:334: endpoint: 0:1d.7 > > (XEN) [VT-D]dmar.c:334: endpoint: 0:1a.0 > > (XEN) [VT-D]dmar.c:334: endpoint: 0:1a.1 > > (XEN) [VT-D]dmar.c:334: endpoint: 0:1a.2 > > (XEN) [VT-D]dmar.c:334: endpoint: 0:1a.7 > > (XEN) [VT-D]dmar.c:571: RMRR region: base_addr bf7ec000 end_address > > bf7fffff > > (XEN) [VT-D]dmar.c:704: found ACPI_DMAR_ATSR: > > (XEN) [VT-D]dmar.c:599: atsru->all_ports: 0 > > (XEN) [VT-D]dmar.c:320: bridge: 0:1.0 start = 0 sec = 1 sub = 1 > > (XEN) [VT-D]dmar.c:320: bridge: 0:3.0 start = 0 sec = 2 sub = 2 > > (XEN) [VT-D]dmar.c:320: bridge: 0:7.0 start = 0 sec = 3 sub = 3 > > (XEN) PCI: MCFG configuration 0: base e0000000 segment 0 buses 0 - 255 > > (XEN) PCI: Not using MMCONFIG. > > (XEN) Using ACPI (MADT) for SMP configuration information > > (XEN) Using scheduler: SMP Credit Scheduler (credit) > > (XEN) Detected 2266.790 MHz processor. > > (XEN) Initing memory sharing. > > (XEN) VMX: Supported advanced features: > > (XEN) - APIC MMIO access virtualisation > > (XEN) - APIC TPR shadow > > (XEN) - Extended Page Tables (EPT) > > (XEN) - Virtual-Processor Identifiers (VPID) > > (XEN) - Virtual NMI > > (XEN) - MSR direct-access bitmap > > (XEN) HVM: ASIDs enabled. > > (XEN) HVM: VMX enabled > > (XEN) HVM: Hardware Assisted Paging detected. > > (XEN) Intel machine check reporting enabled > > (XEN) [VT-D]iommu.c:1078: drhd->address = fbffe000 iommu->reg > > ffff82c3fff57000 > > (XEN) [VT-D]iommu.c:1080: cap = c90780106f0462 ecap = f0207e > > (XEN) Intel VT-d Snoop Control not supported. > > (XEN) Intel VT-d DMA Passthrough not supported. > > (XEN) Intel VT-d Queued Invalidation supported. > > (XEN) Intel VT-d Interrupt Remapping supported. > > (XEN) I/O virtualisation enabled > > (XEN) I/O virtualisation for PV guests disabled > > (XEN) Total of 16 processors activated. > > (XEN) ENABLING IO-APIC IRQs > > (XEN) -> Using new ACK method > > (XEN) ..TIMER: vector=0xF0 apic1=0 pin1=2 apic2=-1 pin2=-1 > > (XEN) TSC is reliable, synchronization unnecessary > > (XEN) Platform timer is 14.318MHz HPET > > ?(XEN) Allocated console ring of 128 KiB. > > (XEN) microcode.c:73:d32767 microcode: CPU1 resumed > > (XEN) microcode.c:73:d32767 microcode: CPU9 resumed > > (XEN) microcode.c:73:d32767 microcode: CPU14 resumed > > (XEN) microcode.c:73:d32767 microcode: CPU6 resumed > > (XEN) microcode.c:73:d32767 microcode: CPU3 resumed > > (XEN) microcode.c:73:d32767 microcode: CPU11 resumed > > (XEN) microcode.c:73:d32767 microcode: CPU8 resumed > > (XEN) microcode.c:73:d32767 microcode: CPU7 resumed > > (XEN) microcode.c:73:d32767 microcode: CPU15 resumed > > (XEN) microcode.c:73:d32767 microcode: CPU2 resumed > > (XEN) microcode.c:73:d32767 microcode: CPU5 resumed > > (XEN) microcode.c:73:d32767 microcode: CPU13 resumed > > (XEN) microcode.c:73:d32767 microcode: CPU4 resumed > > (XEN) microcode.c:73:d32767 microcode: CPU10 resumed > > (XEN) Brought up 16 CPUs > > (XEN) microcode.c:73:d32767 microcode: CPU12 resumed > > (XEN) Turbo Mode detected! > > (XEN) HPET's MSI mode hasn't been supported when Interrupt Remapping is > > enabled. > > (XEN) ACPI sleep modes: S3 > > (XEN) mcheck_poll: Machine check polling timer started. > > (XEN) [VT-D]iommu.c:1325: d0:PCIe: map bdf = 0:0.0 > > (XEN) [VT-D]iommu.c:1325: d0:PCIe: map bdf = 0:14.0 > > (XEN) [VT-D]iommu.c:1325: d0:PCIe: map bdf = 0:14.1 > > (XEN) [VT-D]iommu.c:1325: d0:PCIe: map bdf = 0:14.2 > > (XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = 0:14.3 > > (XEN) [VT-D]iommu.c:1325: d0:PCIe: map bdf = 0:16.0 > > (XEN) [VT-D]iommu.c:1325: d0:PCIe: map bdf = 0:16.1 > > (XEN) [VT-D]iommu.c:1325: d0:PCIe: map bdf = 0:16.2 > > (XEN) [VT-D]iommu.c:1325: d0:PCIe: map bdf = 0:16.3 > > (XEN) [VT-D]iommu.c:1325: d0:PCIe: map bdf = 0:16.4 > > (XEN) [VT-D]iommu.c:1325: d0:PCIe: map bdf = 0:16.5 > > (XEN) [VT-D]iommu.c:1325: d0:PCIe: map bdf = 0:16.6 > > (XEN) [VT-D]iommu.c:1325: d0:PCIe: map bdf = 0:16.7 > > (XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = 0:1a.0 > > (XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = 0:1a.1 > > (XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = 0:1a.2 > > (XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = 0:1a.7 > > (XEN) [VT-D]iommu.c:1325: d0:PCIe: map bdf = 0:1b.0 > > (XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = 0:1d.0 > > (XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = 0:1d.1 > > (XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = 0:1d.2 > > (XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = 0:1d.7 > > (XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = 0:1f.0 > > (XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = 0:1f.2 > > (XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = 0:1f.3 > > (XEN) [VT-D]iommu.c:1325: d0:PCIe: map bdf = 1:0.0 > > (XEN) [VT-D]iommu.c:1325: d0:PCIe: map bdf = 3:0.0 > > (XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = 5:e.0 > > (XEN) [VT-D]iommu.c:1325: d0:PCIe: map bdf = 7:0.0 > > (XEN) [VT-D]iommu.c:1325: d0:PCIe: map bdf = 8:0.0 > > (XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = fe:0.0 > > (XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = fe:0.1 > > (XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = fe:2.0 > > (XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = fe:2.1 > > (XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = fe:2.4 > > (XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = fe:2.5 > > (XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = fe:3.0 > > (XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = fe:3.1 > > (XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = fe:3.2 > > (XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = fe:3.4 > > (XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = fe:4.0 > > (XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = fe:4.1 > > (XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = fe:4.2 > > (XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = fe:4.3 > > (XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = fe:5.0 > > (XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = fe:5.1 > > (XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = fe:5.2 > > (XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = fe:5.3 > > (XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = fe:6.0 > > (XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = fe:6.1 > > (XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = fe:6.2 > > (XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = fe:6.3 > > (XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = ff:0.0 > > (XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = ff:0.1 > > (XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = ff:2.0 > > (XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = ff:2.1 > > (XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = ff:2.4 > > (XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = ff:2.5 > > (XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = ff:3.0 > > (XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = ff:3.1 > > (XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = ff:3.2 > > (XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = ff:3.4 > > (XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = ff:4.0 > > (XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = ff:4.1 > > (XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = ff:4.2 > > (XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = ff:4.3 > > (XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = ff:5.0 > > (XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = ff:5.1 > > (XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = ff:5.2 > > (XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = ff:5.3 > > (XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = ff:6.0 > > (XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = ff:6.1 > > (XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = ff:6.2 > > (XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = ff:6.3 > > (XEN) [VT-D]iommu.c:695: iommu_enable_translation: iommu->reg > > ffff82c3fff57000 > > (XEN) *** LOADING DOMAIN 0 *** > > (XEN) Xen kernel: 64-bit, lsb, compat32 > > (XEN) Dom0 kernel: 64-bit, PAE, lsb, paddr 0x1000000 -> 0x26b6000 > > (XEN) PHYSICAL MEMORY ARRANGEMENT: > > (XEN) Dom0 alloc.: 0000000100000000->0000000120000000 (2937045 pages > > to be allocated) > > (XEN) VIRTUAL MEMORY ARRANGEMENT: > > (XEN) Loaded kernel: ffffffff81000000->ffffffff826b6000 > > (XEN) Init. ramdisk: ffffffff826b6000->ffffffff8f7d7600 > > (XEN) Phys-Mach map: ffffffff8f7d8000->ffffffff90f406a8 > > (XEN) Start info: ffffffff90f41000->ffffffff90f414b4 > > (XEN) Page tables: ffffffff90f42000->ffffffff90fcf000 > > (XEN) Boot stack: ffffffff90fcf000->ffffffff90fd0000 > > (XEN) TOTAL: ffffffff80000000->ffffffff91400000 > > (XEN) ENTRY ADDRESS: ffffffff819be200 > > (XEN) Dom0 has maximum 16 VCPUs > > (XEN) Scrubbing Free RAM: .done. > > (XEN) Xen trace buffers: disabled > > (XEN) Std. Loglevel: All > > (XEN) Guest Loglevel: All > > (XEN) ********************************************** > > (XEN) ******* WARNING: CONSOLE OUTPUT IS SYNCHRONOUS > > (XEN) ******* This option is intended to aid debugging of Xen by > > ensuring > > (XEN) ******* that all output is synchronously delivered on the serial > > line. > > (XEN) ******* However it can introduce SIGNIFICANT latencies and affect > > (XEN) ******* timekeeping. It is NOT recommended for production use! > > (XEN) ********************************************** > > (XEN) 3... 2... 1... > > (XEN) *** Serial input -> DOM0 (type 'CTRL-a' three times to switch > > input to Xen) > > (XEN) Freed 164kB init memory. > > mapping kernel into physical memory > > Xen: setup ISA identity maps > > about to get started... > > (XEN) PCI add device 00:00.0 > > (XEN) PCI add device 00:01.0 > > (XEN) PCI add device 00:03.0 > > (XEN) PCI add device 00:07.0 > > (XEN) PCI add device 00:14.0 > > (XEN) PCI add device 00:14.1 > > (XEN) PCI add device 00:14.2 > > (XEN) PCI add device 00:14.3 > > (XEN) PCI add device 00:16.0 > > (XEN) PCI add device 00:16.1 > > (XEN) PCI add device 00:16.2 > > (XEN) PCI add device 00:16.3 > > (XEN) PCI add device 00:16.4 > > (XEN) PCI add device 00:16.5 > > (XEN) PCI add device 00:16.6 > > (XEN) PCI add device 00:16.7 > > (XEN) PCI add device 00:1a.0 > > (XEN) PCI add device 00:1a.1 > > (XEN) PCI add device 00:1a.2 > > (XEN) PCI add device 00:1a.7 > > (XEN) PCI add device 00:1b.0 > > (XEN) PCI add device 00:1c.0 > > (XEN) PCI add device 00:1c.4 > > (XEN) PCI add device 00:1c.5 > > (XEN) PCI add device 00:1d.0 > > (XEN) PCI add device 00:1d.1 > > (XEN) PCI add device 00:1d.2 > > (XEN) PCI add device 00:1d.7 > > (XEN) PCI add device 00:1e.0 > > (XEN) PCI add device 00:1f.0 > > (XEN) PCI add device 00:1f.2 > > (XEN) PCI add device 00:1f.3 > > (XEN) PCI add device 01:00.0 > > (XEN) PCI add device 03:00.0 > > (XEN) PCI add device 04:00.0 > > (XEN) PCI add device 04:00.2 > > (XEN) PCI add device 05:0e.0 > > (XEN) PCI add device 07:00.0 > > (XEN) PCI add device 08:00.0 > > (XEN) cpuid.MWAIT[.eax=40, .ebx=40, .ecx=3, .edx=1120] > > (XEN) Monitor-Mwait will be used to enter C-1 state > > (XEN) cpuid.MWAIT[.eax=40, .ebx=40, .ecx=3, .edx=1120] > > (XEN) Monitor-Mwait will be used to enter C-3 state > > (XEN) cpuid.MWAIT[.eax=40, .ebx=40, .ecx=3, .edx=1120] > > (XEN) Monitor-Mwait will be used to enter C-3 state > > (XEN) cpuid.MWAIT[.eax=40, .ebx=40, .ecx=3, .edx=1120] > > (XEN) Monitor-Mwait will be used to enter C-1 state > > (XEN) cpuid.MWAIT[.eax=40, .ebx=40, .ecx=3, .edx=1120] > > (XEN) Monitor-Mwait will be used to enter C-3 state > > (XEN) cpuid.MWAIT[.eax=40, .ebx=40, .ecx=3, .edx=1120] > > (XEN) Monitor-Mwait will be used to enter C-3 state > > (XEN) cpuid.MWAIT[.eax=40, .ebx=40, .ecx=3, .edx=1120] > > (XEN) Monitor-Mwait will be used to enter C-1 state > > (XEN) cpuid.MWAIT[.eax=40, .ebx=40, .ecx=3, .edx=1120] > > (XEN) Monitor-Mwait will be used to enter C-3 state > > (XEN) cpuid.MWAIT[.eax=40, .ebx=40, .ecx=3, .edx=1120] > > (XEN) Monitor-Mwait will be used to enter C-3 state > > (XEN) cpuid.MWAIT[.eax=40, .ebx=40, .ecx=3, .edx=1120] > > (XEN) Monitor-Mwait will be used to enter C-1 state > > (XEN) cpuid.MWAIT[.eax=40, .ebx=40, .ecx=3, .edx=1120] > > (XEN) Monitor-Mwait will be used to enter C-3 state > > (XEN) cpuid.MWAIT[.eax=40, .ebx=40, .ecx=3, .edx=1120] > > (XEN) Monitor-Mwait will be used to enter C-3 state > > (XEN) cpuid.MWAIT[.eax=40, .ebx=40, .ecx=3, .edx=1120] > > (XEN) Monitor-Mwait will be used to enter C-1 state > > (XEN) cpuid.MWAIT[.eax=40, .ebx=40, .ecx=3, .edx=1120] > > (XEN) Monitor-Mwait will be used to enter C-3 state > > (XEN) cpuid.MWAIT[.eax=40, .ebx=40, .ecx=3, .edx=1120] > > (XEN) Monitor-Mwait will be used to enter C-3 state > > (XEN) cpuid.MWAIT[.eax=40, .ebx=40, .ecx=3, .edx=1120] > > (XEN) Monitor-Mwait will be used to enter C-1 state > > (XEN) cpuid.MWAIT[.eax=40, .ebx=40, .ecx=3, .edx=1120] > > (XEN) Monitor-Mwait will be used to enter C-3 state > > (XEN) cpuid.MWAIT[.eax=40, .ebx=40, .ecx=3, .edx=1120] > > (XEN) Monitor-Mwait will be used to enter C-3 state > > (XEN) cpuid.MWAIT[.eax=40, .ebx=40, .ecx=3, .edx=1120] > > (XEN) Monitor-Mwait will be used to enter C-1 state > > (XEN) cpuid.MWAIT[.eax=40, .ebx=40, .ecx=3, .edx=1120] > > (XEN) Monitor-Mwait will be used to enter C-3 state > > (XEN) cpuid.MWAIT[.eax=40, .ebx=40, .ecx=3, .edx=1120] > > (XEN) Monitor-Mwait will be used to enter C-3 state > > (XEN) cpuid.MWAIT[.eax=40, .ebx=40, .ecx=3, .edx=1120] > > (XEN) Monitor-Mwait will be used to enter C-1 state > > (XEN) cpuid.MWAIT[.eax=40, .ebx=40, .ecx=3, .edx=1120] > > (XEN) Monitor-Mwait will be used to enter C-3 state > > (XEN) cpuid.MWAIT[.eax=40, .ebx=40, .ecx=3, .edx=1120] > > (XEN) Monitor-Mwait will be used to enter C-3 state > > (XEN) cpuid.MWAIT[.eax=40, .ebx=40, .ecx=3, .edx=1120] > > (XEN) Monitor-Mwait will be used to enter C-1 state > > (XEN) cpuid.MWAIT[.eax=40, .ebx=40, .ecx=3, .edx=1120] > > (XEN) Monitor-Mwait will be used to enter C-3 state > > (XEN) cpuid.MWAIT[.eax=40, .ebx=40, .ecx=3, .edx=1120] > > (XEN) Monitor-Mwait will be used to enter C-3 state > > (XEN) cpuid.MWAIT[.eax=40, .ebx=40, .ecx=3, .edx=1120] > > (XEN) Monitor-Mwait will be used to enter C-1 state > > (XEN) cpuid.MWAIT[.eax=40, .ebx=40, .ecx=3, .edx=1120] > > (XEN) Monitor-Mwait will be used to enter C-3 state > > (XEN) cpuid.MWAIT[.eax=40, .ebx=40, .ecx=3, .edx=1120] > > (XEN) Monitor-Mwait will be used to enter C-3 state > > (XEN) cpuid.MWAIT[.eax=40, .ebx=40, .ecx=3, .edx=1120] > > (XEN) Monitor-Mwait will be used to enter C-1 state > > (XEN) cpuid.MWAIT[.eax=40, .ebx=40, .ecx=3, .edx=1120] > > (XEN) Monitor-Mwait will be used to enter C-3 state > > (XEN) cpuid.MWAIT[.eax=40, .ebx=40, .ecx=3, .edx=1120] > > (XEN) Monitor-Mwait will be used to enter C-3 state > > (XEN) cpuid.MWAIT[.eax=40, .ebx=40, .ecx=3, .edx=1120] > > (XEN) Monitor-Mwait will be used to enter C-1 state > > (XEN) cpuid.MWAIT[.eax=40, .ebx=40, .ecx=3, .edx=1120] > > (XEN) Monitor-Mwait will be used to enter C-3 state > > (XEN) cpuid.MWAIT[.eax=40, .ebx=40, .ecx=3, .edx=1120] > > (XEN) Monitor-Mwait will be used to enter C-3 state > > (XEN) cpuid.MWAIT[.eax=40, .ebx=40, .ecx=3, .edx=1120] > > (XEN) Monitor-Mwait will be used to enter C-1 state > > (XEN) cpuid.MWAIT[.eax=40, .ebx=40, .ecx=3, .edx=1120] > > (XEN) Monitor-Mwait will be used to enter C-3 state > > (XEN) cpuid.MWAIT[.eax=40, .ebx=40, .ecx=3, .edx=1120] > > (XEN) Monitor-Mwait will be used to enter C-3 state > > (XEN) cpuid.MWAIT[.eax=40, .ebx=40, .ecx=3, .edx=1120] > > (XEN) Monitor-Mwait will be used to enter C-1 state > > (XEN) cpuid.MWAIT[.eax=40, .ebx=40, .ecx=3, .edx=1120] > > (XEN) Monitor-Mwait will be used to enter C-3 state > > (XEN) cpuid.MWAIT[.eax=40, .ebx=40, .ecx=3, .edx=1120] > > (XEN) Monitor-Mwait will be used to enter C-3 state > > (XEN) cpuid.MWAIT[.eax=40, .ebx=40, .ecx=3, .edx=1120] > > (XEN) Monitor-Mwait will be used to enter C-1 state > > (XEN) cpuid.MWAIT[.eax=40, .ebx=40, .ecx=3, .edx=1120] > > (XEN) Monitor-Mwait will be used to enter C-3 state > > (XEN) cpuid.MWAIT[.eax=40, .ebx=40, .ecx=3, .edx=1120] > > (XEN) Monitor-Mwait will be used to enter C-3 state > > (XEN) cpuid.MWAIT[.eax=40, .ebx=40, .ecx=3, .edx=1120] > > (XEN) Monitor-Mwait will be used to enter C-1 state > > (XEN) cpuid.MWAIT[.eax=40, .ebx=40, .ecx=3, .edx=1120] > > (XEN) Monitor-Mwait will be used to enter C-3 state > > (XEN) cpuid.MWAIT[.eax=40, .ebx=40, .ecx=3, .edx=1120] > > (XEN) Monitor-Mwait will be used to enter C-3 state > > (XEN) irq.c:1139:d0 Cannot bind IRQ 4 to guest. In use by 'ns16550'. > > (XEN) irq.c:1139:d0 Cannot bind IRQ 2 to guest. In use by 'cascade'. > > (XEN) irq.c:1139:d0 Cannot bind IRQ 4 to guest. In use by 'ns16550'. > > (XEN) irq.c:1139:d0 Cannot bind IRQ 2 to guest. In use by 'cascade'. > > (XEN) irq.c:1139:d0 Cannot bind IRQ 4 to guest. In use by 'ns16550'. > > (XEN) irq.c:1139:d0 Cannot bind IRQ 2 to guest. In use by 'cascade'. > > (XEN) irq.c:1139:d0 Cannot bind IRQ 4 to guest. In use by 'ns16550'. > > (XEN) irq.c:1139:d0 Cannot bind IRQ 2 to guest. In use by 'cascade'. > > (XEN) [VT-D]iommu.c:821: iommu_fault_status: Primary Pending Fault > > (XEN) [VT-D]iommu.c:796: DMAR:[DMA Write] Request device [05:08.0] fault > > addr 203a09000, iommu reg = ffff82c3fff57000 > > (XEN) DMAR:[fault reason 02h] Present bit in context entry is clear > > (XEN) print_vtd_entries: iommu = ffff83013fffaee0 bdf = 5:8.0 gmfn > > 203a09 > > (XEN) root_entry = ffff83013ff37000 > > (XEN) root_entry[5] = 13cf12001 > > (XEN) context = ffff83013cf12000 > > (XEN) context[40] = 0_0 > > (XEN) ctxt_entry[40] not present > > (XEN) [VT-D]iommu.c:796: DMAR:[DMA Write] Request device [05:08.0] fault > > addr 203eba000, iommu reg = ffff82c3fff57000 > > (XEN) DMAR:[fault reason 02h] Present bit in context entry is clear > > (XEN) print_vtd_entries: iommu = ffff83013fffaee0 bdf = 5:8.0 gmfn > > 203eba > > (XEN) root_entry = ffff83013ff37000 > > (XEN) root_entry[5] = 13cf12001 > > (XEN) context = ffff83013cf12000 > > (XEN) context[40] = 0_0 > > (XEN) ctxt_entry[40] not present > > (XEN) [VT-D]iommu.c:821: iommu_fault_status: Primary Pending Fault > > (XEN) [VT-D]iommu.c:796: DMAR:[DMA Write] Request device [05:08.0] fault > > addr 204e11000, iommu reg = ffff82c3fff57000 > > (XEN) DMAR:[fault reason 02h] Present bit in context entry is clear > > (XEN) print_vtd_entries: iommu = ffff83013fffaee0 bdf = 5:8.0 gmfn > > 204e11 > > (XEN) root_entry = ffff83013ff37000 > > (XEN) root_entry[5] = 13cf12001 > > (XEN) context = ffff83013cf12000 > > (XEN) context[40] = 0_0 > > (XEN) ctxt_entry[40] not present > > (XEN) [VT-D]iommu.c:821: iommu_fault_status: Primary Pending Fault > > (XEN) [VT-D]iommu.c:796: DMAR:[DMA Write] Request device [05:08.0] fault > > addr 2061e2000, iommu reg = ffff82c3fff57000 > > (XEN) DMAR:[fault reason 02h] Present bit in context entry is clear > > (XEN) print_vtd_entries: iommu = ffff83013fffaee0 bdf = 5:8.0 gmfn > > 2061e2 > > (XEN) root_entry = ffff83013ff37000 > > (XEN) root_entry[5] = 13cf12001 > > (XEN) context = ffff83013cf12000 > > (XEN) context[40] = 0_0 > > (XEN) ctxt_entry[40] not present > > (XEN) [VT-D]iommu.c:796: DMAR:[DMA Write] Request device [05:08.0] fault > > addr 205043000, iommu reg = ffff82c3fff57000 > > (XEN) DMAR:[fault reason 02h] Present bit in context entry is clear > > (XEN) print_vtd_entries: iommu = ffff83013fffaee0 bdf = 5:8.0 gmfn > > 205043 > > (XEN) root_entry = ffff83013ff37000 > > (XEN) root_entry[5] = 13cf12001 > > (XEN) context = ffff83013cf12000 > > (XEN) context[40] = 0_0 > > (XEN) ctxt_entry[40] not present > > (XEN) [VT-D]iommu.c:821: iommu_fault_status: Primary Pending Fault > > (XEN) [VT-D]iommu.c:796: DMAR:[DMA Write] Request device [05:08.0] fault > > addr 20552b000, iommu reg = ffff82c3fff57000 > > (XEN) DMAR:[fault reason 02h] Present bit in context entry is clear > > (XEN) print_vtd_entries: iommu = ffff83013fffaee0 bdf = 5:8.0 gmfn > > 20552b > > (XEN) root_entry = ffff83013ff37000 > > (XEN) root_entry[5] = 13cf12001 > > (XEN) context = ffff83013cf12000 > > (XEN) context[40] = 0_0 > > (XEN) ctxt_entry[40] not present > > (XEN) [VT-D]iommu.c:821: iommu_fault_status: Primary Pending Fault > > (XEN) [VT-D]iommu.c:796: DMAR:[DMA Write] Request device [05:08.0] fault > > addr 205708000, iommu reg = ffff82c3fff57000 > > (XEN) DMAR:[fault reason 02h] Present bit in context entry is clear > > (XEN) print_vtd_entries: iommu = ffff83013fffaee0 bdf = 5:8.0 gmfn > > 205708 > > (XEN) root_entry = ffff83013ff37000 > > (XEN) root_entry[5] = 13cf12001 > > (XEN) context = ffff83013cf12000 > > (XEN) context[40] = 0_0 > > (XEN) ctxt_entry[40] not present > > (XEN) [VT-D]iommu.c:796: DMAR:[DMA Write] Request device [05:08.0] fault > > addr 2060c0000, iommu reg = ffff82c3fff57000 > > (XEN) DMAR:[fault reason 02h] Present bit in context entry is clear > > (XEN) print_vtd_entries: iommu = ffff83013fffaee0 bdf = 5:8.0 gmfn > > 2060c0 > > (XEN) root_entry = ffff83013ff37000 > > (XEN) root_entry[5] = 13cf12001 > > (XEN) context = ffff83013cf12000 > > (XEN) context[40] = 0_0 > > (XEN) ctxt_entry[40] not present > > (XEN) [VT-D]iommu.c:821: iommu_fault_status: Primary Pending Fault > > (XEN) [VT-D]iommu.c:796: DMAR:[DMA Write] Request device [05:08.0] fault > > addr 206591000, iommu reg = ffff82c3fff57000 > > (XEN) DMAR:[fault reason 02h] Present bit in context entry is clear > > (XEN) print_vtd_entries: iommu = ffff83013fffaee0 bdf = 5:8.0 gmfn > > 206591 > > (XEN) root_entry = ffff83013ff37000 > > (XEN) root_entry[5] = 13cf12001 > > (XEN) context = ffff83013cf12000 > > (XEN) context[40] = 0_0 > > (XEN) ctxt_entry[40] not present > > (XEN) [VT-D]iommu.c:796: DMAR:[DMA Write] Request device [05:08.0] fault > > addr 204353000, iommu reg = ffff82c3fff57000 > > (XEN) DMAR:[fault reason 02h] Present bit in context entry is clear > > (XEN) print_vtd_entries: iommu = ffff83013fffaee0 bdf = 5:8.0 gmfn > > 204353 > > (XEN) root_entry = ffff83013ff37000 > > (XEN) root_entry[5] = 13cf12001 > > (XEN) context = ffff83013cf12000 > > (XEN) context[40] = 0_0 > > (XEN) ctxt_entry[40] not present > > (XEN) [VT-D]iommu.c:821: iommu_fault_status: Primary Pending Fault > > (XEN) [VT-D]iommu.c:796: DMAR:[DMA Write] Request device [05:08.0] fault > > addr 2061f2000, iommu reg = ffff82c3fff57000 > > (XEN) DMAR:[fault reason 02h] Present bit in context entry is clear > > (XEN) print_vtd_entries: iommu = ffff83013fffaee0 bdf = 5:8.0 gmfn > > 2061f2 > > (XEN) root_entry = ffff83013ff37000 > > (XEN) root_entry[5] = 13cf12001 > > (XEN) context = ffff83013cf12000 > > (XEN) context[40] = 0_0 > > (XEN) ctxt_entry[40] not present > > (XEN) [VT-D]iommu.c:796: DMAR:[DMA Write] Request device [05:08.0] fault > > addr 204306000, iommu reg = ffff82c3fff57000 > > (XEN) DMAR:[fault reason 02h] Present bit in context entry is clear > > (XEN) print_vtd_entries: iommu = ffff83013fffaee0 bdf = 5:8.0 gmfn > > 204306 > > (XEN) root_entry = ffff83013ff37000 > > (XEN) root_entry[5] = 13cf12001 > > (XEN) context = ffff83013cf12000 > > (XEN) context[40] = 0_0 > > (XEN) ctxt_entry[40] not present > > (XEN) [VT-D]iommu.c:821: iommu_fault_status: Primary Pending Fault > > (XEN) [VT-D]iommu.c:796: DMAR:[DMA Write] Request device [05:08.0] fault > > addr 205f6b000, iommu reg = ffff82c3fff57000 > > (XEN) DMAR:[fault reason 02h] Present bit in context entry is clear > > (XEN) print_vtd_entries: iommu = ffff83013fffaee0 bdf = 5:8.0 gmfn > > 205f6b > > (XEN) root_entry = ffff83013ff37000 > > (XEN) root_entry[5] = 13cf12001 > > (XEN) context = ffff83013cf12000 > > (XEN) context[40] = 0_0 > > (XEN) ctxt_entry[40] not present > > (XEN) [VT-D]iommu.c:796: DMAR:[DMA Write] Request device [05:08.0] fault > > addr 205665000, iommu reg = ffff82c3fff57000 > > (XEN) DMAR:[fault reason 02h] Present bit in context entry is clear > > (XEN) print_vtd_entries: iommu = ffff83013fffaee0 bdf = 5:8.0 gmfn > > 205665 > > (XEN) root_entry = ffff83013ff37000 > > (XEN) root_entry[5] = 13cf12001 > > (XEN) context = ffff83013cf12000 > > (XEN) context[40] = 0_0 > > (XEN) ctxt_entry[40] not present > > (XEN) [VT-D]iommu.c:821: iommu_fault_status: Primary Pending Fault > > (XEN) [VT-D]iommu.c:796: DMAR:[DMA Write] Request device [05:08.0] fault > > addr 2045a0000, iommu reg = ffff82c3fff57000 > > (XEN) DMAR:[fault reason 02h] Present bit in context entry is clear > > (XEN) print_vtd_entries: iommu = ffff83013fffaee0 bdf = 5:8.0 gmfn > > 2045a0 > > (XEN) root_entry = ffff83013ff37000 > > (XEN) root_entry[5] = 13cf12001 > > (XEN) context = ffff83013cf12000 > > (XEN) context[40] = 0_0 > > (XEN) ctxt_entry[40] not present > > (XEN) [VT-D]iommu.c:796: DMAR:[DMA Write] Request device [05:08.0] fault > > addr 205669000, iommu reg = ffff82c3fff57000 > > (XEN) DMAR:[fault reason 02h] Present bit in context entry is clear > > (XEN) print_vtd_entries: iommu = ffff83013fffaee0 bdf = 5:8.0 gmfn > > 205669 > > (XEN) root_entry = ffff83013ff37000 > > (XEN) root_entry[5] = 13cf12001 > > (XEN) context = ffff83013cf12000 > > (XEN) context[40] = 0_0 > > (XEN) ctxt_entry[40] not present > > (XEN) [VT-D]iommu.c:821: iommu_fault_status: Primary Pending Fault > > (XEN) [VT-D]iommu.c:796: DMAR:[DMA Write] Request device [05:08.0] fault > > addr 2042c6000, iommu reg = ffff82c3fff57000 > > (XEN) DMAR:[fault reason 02h] Present bit in context entry is clear > > (XEN) print_vtd_entries: iommu = ffff83013fffaee0 bdf = 5:8.0 gmfn > > 2042c6 > > (XEN) root_entry = ffff83013ff37000 > > (XEN) root_entry[5] = 13cf12001 > > (XEN) context = ffff83013cf12000 > > (XEN) context[40] = 0_0 > > (XEN) ctxt_entry[40] not present > > (XEN) [VT-D]iommu.c:796: DMAR:[DMA Write] Request device [05:08.0] fault > > addr 2061fe000, iommu reg = ffff82c3fff57000 > > (XEN) DMAR:[fault reason 02h] Present bit in context entry is clear > > (XEN) print_vtd_entries: iommu = ffff83013fffaee0 bdf = 5:8.0 gmfn > > 2061fe > > (XEN) root_entry = ffff83013ff37000 > > (XEN) root_entry[5] = 13cf12001 > > (XEN) context = ffff83013cf12000 > > (XEN) context[40] = 0_0 > > (XEN) ctxt_entry[40] not present > > (XEN) [VT-D]iommu.c:821: iommu_fault_status: Primary Pending Fault > > (XEN) [VT-D]iommu.c:796: DMAR:[DMA Write] Request device [05:08.0] fault > > addr 20560a000, iommu reg = ffff82c3fff57000 > > (XEN) DMAR:[fault reason 02h] Present bit in context entry is clear > > (XEN) print_vtd_entries: iommu = ffff83013fffaee0 bdf = 5:8.0 gmfn > > 20560a > > (XEN) root_entry = ffff83013ff37000 > > (XEN) root_entry[5] = 13cf12001 > > (XEN) context = ffff83013cf12000 > > (XEN) context[40] = 0_0 > > (XEN) ctxt_entry[40] not present > > (XEN) [VT-D]iommu.c:796: DMAR:[DMA Write] Request device [05:08.0] fault > > addr 206003000, iommu reg = ffff82c3fff57000 > > (XEN) DMAR:[fault reason 02h] Present bit in context entry is clear > > (XEN) print_vtd_entries: iommu = ffff83013fffaee0 bdf = 5:8.0 gmfn > > 206003 > > (XEN) root_entry = ffff83013ff37000 > > (XEN) root_entry[5] = 13cf12001 > > (XEN) context = ffff83013cf12000 > > (XEN) context[40] = 0_0 > > (XEN) ctxt_entry[40] not present > > (XEN) [VT-D]iommu.c:821: iommu_fault_status: Primary Pending Fault > > (XEN) [VT-D]iommu.c:796: DMAR:[DMA Write] Request device [05:08.0] fault > > addr 20583e000, iommu reg = ffff82c3fff57000 > > (XEN) DMAR:[fault reason 02h] Present bit in context entry is clear > > (XEN) print_vtd_entries: iommu = ffff83013fffaee0 bdf = 5:8.0 gmfn > > 20583e > > (XEN) root_entry = ffff83013ff37000 > > (XEN) root_entry[5] = 13cf12001 > > (XEN) context = ffff83013cf12000 > > (XEN) context[40] = 0_0 > > (XEN) ctxt_entry[40] not present > > (XEN) [VT-D]iommu.c:796: DMAR:[DMA Write] Request device [05:08.0] fault > > addr 205615000, iommu reg = ffff82c3fff57000 > > (XEN) DMAR:[fault reason 02h] Present bit in context entry is clear > > (XEN) print_vtd_entries: iommu = ffff83013fffaee0 bdf = 5:8.0 gmfn > > 205615 > > (XEN) root_entry = ffff83013ff37000 > > (XEN) root_entry[5] = 13cf12001 > > (XEN) context = ffff83013cf12000 > > (XEN) context[40] = 0_0 > > (XEN) ctxt_entry[40] not present > > (XEN) [VT-D]iommu.c:796: DMAR:[DMA Write] Request device [05:08.0] fault > > addr 204265000, iommu reg = ffff82c3fff57000 > > (XEN) DMAR:[fault reason 02h] Present bit in context entry is clear > > (XEN) print_vtd_entries: iommu = ffff83013fffaee0 bdf = 5:8.0 gmfn > > 204265 > > (XEN) root_entry = ffff83013ff37000 > > (XEN) root_entry[5] = 13cf12001 > > (XEN) context = ffff83013cf12000 > > (XEN) context[40] = 0_0 > > (XEN) ctxt_entry[40] not present > > (XEN) [VT-D]iommu.c:821: iommu_fault_status: Primary Pending Fault > > (XEN) [VT-D]iommu.c:796: DMAR:[DMA Write] Request device [05:08.0] fault > > addr 207498000, iommu reg = ffff82c3fff57000 > > (XEN) DMAR:[fault reason 02h] Present bit in context entry is clear > > (XEN) print_vtd_entries: iommu = ffff83013fffaee0 bdf = 5:8.0 gmfn > > 207498 > > (XEN) root_entry = ffff83013ff37000 > > (XEN) root_entry[5] = 13cf12001 > > (XEN) context = ffff83013cf12000 > > (XEN) context[40] = 0_0 > > (XEN) ctxt_entry[40] not present > > (XEN) [VT-D]iommu.c:821: iommu_fault_status: Primary Pending Fault > > (XEN) [VT-D]iommu.c:796: DMAR:[DMA Write] Request device [05:08.0] fault > > addr 2049d1000, iommu reg = ffff82c3fff57000 > > (XEN) DMAR:[fault reason 02h] Present bit in context entry is clear > > (XEN) print_vtd_entries: iommu = ffff83013fffaee0 bdf = 5:8.0 gmfn > > 2049d1 > > (XEN) root_entry = ffff83013ff37000 > > (XEN) root_entry[5] = 13cf12001 > > (XEN) context = ffff83013cf12000 > > (XEN) context[40] = 0_0 > > (XEN) ctxt_entry[40] not present > > (XEN) [VT-D]iommu.c:821: iommu_fault_status: Primary Pending Fault > > (XEN) [VT-D]iommu.c:796: DMAR:[DMA Write] Request device [05:08.0] fault > > addr 20488e000, iommu reg = ffff82c3fff57000 > > (XEN) DMAR:[fault reason 02h] Present bit in context entry is clear > > (XEN) print_vtd_entries: iommu = ffff83013fffaee0 bdf = 5:8.0 gmfn > > 20488e > > (XEN) root_entry = ffff83013ff37000 > > (XEN) root_entry[5] = 13cf12001 > > (XEN) context = ffff83013cf12000 > > (XEN) context[40] = 0_0 > > (XEN) ctxt_entry[40] not present > > (XEN) [VT-D]iommu.c:821: iommu_fault_status: Primary Pending Fault > > (XEN) [VT-D]iommu.c:796: DMAR:[DMA Write] Request device [05:08.0] fault > > addr 205495000, iommu reg = ffff82c3fff57000 > > (XEN) DMAR:[fault reason 02h] Present bit in context entry is clear > > (XEN) print_vtd_entries: iommu = ffff83013fffaee0 bdf = 5:8.0 gmfn > > 205495 > > (XEN) root_entry = ffff83013ff37000 > > (XEN) root_entry[5] = 13cf12001 > > (XEN) context = ffff83013cf12000 > > (XEN) context[40] = 0_0 > > (XEN) ctxt_entry[40] not present > > (XEN) [VT-D]iommu.c:821: iommu_fault_status: Primary Pending Fault > > (XEN) [VT-D]iommu.c:796: DMAR:[DMA Write] Request device [05:08.0] fault > > addr 2072d8000, iommu reg = ffff82c3fff57000 > > (XEN) DMAR:[fault reason 02h] Present bit in context entry is clear > > (XEN) print_vtd_entries: iommu = ffff83013fffaee0 bdf = 5:8.0 gmfn > > 2072d8 > > (XEN) root_entry = ffff83013ff37000 > > (XEN) root_entry[5] = 13cf12001 > > (XEN) context = ffff83013cf12000 > > (XEN) context[40] = 0_0 > > (XEN) ctxt_entry[40] not present > > (XEN) [VT-D]iommu.c:821: iommu_fault_status: Primary Pending Fault > > (XEN) [VT-D]iommu.c:796: DMAR:[DMA Write] Request device [05:08.0] fault > > addr 2055ae000, iommu reg = ffff82c3fff57000 > > (XEN) DMAR:[fault reason 02h] Present bit in context entry is clear > > (XEN) print_vtd_entries: iommu = ffff83013fffaee0 bdf = 5:8.0 gmfn > > 2055ae > > (XEN) root_entry = ffff83013ff37000 > > (XEN) root_entry[5] = 13cf12001 > > (XEN) context = ffff83013cf12000 > > (XEN) context[40] = 0_0 > > (XEN) ctxt_entry[40] not present > > (XEN) [VT-D]iommu.c:821: iommu_fault_status: Primary Pending Fault > > (XEN) [VT-D]iommu.c:796: DMAR:[DMA Write] Request device [05:08.0] fault > > addr 205544000, iommu reg = ffff82c3fff57000 > > (XEN) DMAR:[fault reason 02h] Present bit in context entry is clear > > (XEN) print_vtd_entries: iommu = ffff83013fffaee0 bdf = 5:8.0 gmfn > > 205544 > > (XEN) root_entry = ffff83013ff37000 > > (XEN) root_entry[5] = 13cf12001 > > (XEN) context = ffff83013cf12000 > > (XEN) context[40] = 0_0 > > (XEN) ctxt_entry[40] not present > > (XEN) [VT-D]iommu.c:796: DMAR:[DMA Write] Request device [05:08.0] fault > > addr 204865000, iommu reg = ffff82c3fff57000 > > (XEN) DMAR:[fault reason 02h] Present bit in context entry is clear > > (XEN) print_vtd_entries: iommu = ffff83013fffaee0 bdf = 5:8.0 gmfn > > 204865 > > (XEN) root_entry = ffff83013ff37000 > > (XEN) root_entry[5] = 13cf12001 > > (XEN) context = ffff83013cf12000 > > (XEN) context[40] = 0_0 > > (XEN) ctxt_entry[40] not present > > (XEN) [VT-D]iommu.c:821: iommu_fault_status: Primary Pending Fault > > (XEN) [VT-D]iommu.c:796: DMAR:[DMA Write] Request device [05:08.0] fault > > addr 2074be000, iommu reg = ffff82c3fff57000 > > (XEN) DMAR:[fault reason 02h] Present bit in context entry is clear > > (XEN) print_vtd_entries: iommu = ffff83013fffaee0 bdf = 5:8.0 gmfn > > 2074be > > (XEN) root_entry = ffff83013ff37000 > > (XEN) root_entry[5] = 13cf12001 > > (XEN) context = ffff83013cf12000 > > (XEN) context[40] = 0_0 > > (XEN) ctxt_entry[40] not present > > > > (XEN) [VT-D]iommu.c:796: DMAR:[DMA Write] Request device [05:08.0] fault > > addr 204865000, iommu reg = ffff82c3fff57000 > > (XEN) DMAR:[fault reason 02h] Present bit in context entry is clear > > (XEN) print_vtd_entries: iommu = ffff83013fffaee0 bdf = 5:8.0 gmfn > > 204865 > > (XEN) root_entry = ffff83013ff37000 > > (XEN) root_entry[5] = 13cf12001 > > (XEN) context = ffff83013cf12000 > > (XEN) context[40] = 0_0 > > (XEN) ctxt_entry[40] not present > > (XEN) [VT-D]iommu.c:821: iommu_fault_status: Primary Pending Fault > > (XEN) [VT-D]iommu.c:796: DMAR:[DMA Write] Request device [05:08.0] fault > > addr 2074be000, iommu reg = ffff82c3fff57000 > > (XEN) DMAR:[fault reason 02h] Present bit in context entry is clear > > (XEN) print_vtd_entries: iommu = ffff83013fffaee0 bdf = 5:8.0 gmfn > > 2074be > > (XEN) root_entry = ffff83013ff37000 > > (XEN) root_entry[5] = 13cf12001 > > (XEN) context = ffff83013cf12000 > > (XEN) context[40] = 0_0 > > (XEN) ctxt_entry[40] not present > > > > (XEN) [VT-D]iommu.c:796: DMAR:[DMA Write] Request device [05:08.0] fault > > addr 204865000, iommu reg = ffff82c3fff57000 > > (XEN) DMAR:[fault reason 02h] Present bit in context entry is clear > > (XEN) print_vtd_entries: iommu = ffff83013fffaee0 bdf = 5:8.0 gmfn > > 204865 > > (XEN) root_entry = ffff83013ff37000 > > (XEN) root_entry[5] = 13cf12001 > > (XEN) context = ffff83013cf12000 > > (XEN) context[40] = 0_0 > > (XEN) ctxt_entry[40] not present > > (XEN) [VT-D]iommu.c:821: iommu_fault_status: Primary Pending Fault > > (XEN) [VT-D]iommu.c:796: DMAR:[DMA Write] Request device [05:08.0] fault > > addr 2074be000, iommu reg = ffff82c3fff57000 > > (XEN) DMAR:[fault reason 02h] Present bit in context entry is clear > > (XEN) print_vtd_entries: iommu = ffff83013fffaee0 bdf = 5:8.0 gmfn > > 2074be > > (XEN) root_entry = ffff83013ff37000 > > (XEN) root_entry[5] = 13cf12001 > > (XEN) context = ffff83013cf12000 > > (XEN) context[40] = 0_0 > > (XEN) ctxt_entry[40] not present > > > > (XEN) [VT-D]iommu.c:796: DMAR:[DMA Write] Request device [05:08.0] fault > > addr 204865000, iommu reg = ffff82c3fff57000 > > (XEN) DMAR:[fault reason 02h] Present bit in context entry is clear > > (XEN) print_vtd_entries: iommu = ffff83013fffaee0 bdf = 5:8.0 gmfn > > 204865 > > (XEN) root_entry = ffff83013ff37000 > > (XEN) root_entry[5] = 13cf12001 > > (XEN) context = ffff83013cf12000 > > (XEN) context[40] = 0_0 > > (XEN) ctxt_entry[40] not present > > (XEN) [VT-D]iommu.c:821: iommu_fault_status: Primary Pending Fault > > (XEN) [VT-D]iommu.c:796: DMAR:[DMA Write] Request device [05:08.0] fault > > addr 2074be000, iommu reg = ffff82c3fff57000 > > (XEN) DMAR:[fault reason 02h] Present bit in context entry is clear > > (XEN) print_vtd_entries: iommu = ffff83013fffaee0 bdf = 5:8.0 gmfn > > 2074be > > (XEN) root_entry = ffff83013ff37000 > > (XEN) root_entry[5] = 13cf12001 > > (XEN) context = ffff83013cf12000 > > (XEN) context[40] = 0_0 > > (XEN) ctxt_entry[40] not present > > > > (XEN) [VT-D]iommu.c:796: DMAR:[DMA Write] Request device [05:08.0] fault > > addr 204865000, iommu reg = ffff82c3fff57000 > > (XEN) DMAR:[fault reason 02h] Present bit in context entry is clear > > (XEN) print_vtd_entries: iommu = ffff83013fffaee0 bdf = 5:8.0 gmfn > > 204865 > > (XEN) root_entry = ffff83013ff37000 > > (XEN) root_entry[5] = 13cf12001 > > (XEN) context = ffff83013cf12000 > > (XEN) context[40] = 0_0 > > (XEN) ctxt_entry[40] not present > > (XEN) [VT-D]iommu.c:821: iommu_fault_status: Primary Pending Fault > > (XEN) [VT-D]iommu.c:796: DMAR:[DMA Write] Request device [05:08.0] fault > > addr 2074be000, iommu reg = ffff82c3fff57000 > > (XEN) DMAR:[fault reason 02h] Present bit in context entry is clear > > (XEN) print_vtd_entries: iommu = ffff83013fffaee0 bdf = 5:8.0 gmfn > > 2074be > > (XEN) root_entry = ffff83013ff37000 > > (XEN) root_entry[5] = 13cf12001 > > (XEN) context = ffff83013cf12000 > > (XEN) context[40] = 0_0 > > (XEN) ctxt_entry[40] not present > > > > (XEN) [VT-D]iommu.c:796: DMAR:[DMA Write] Request device [05:08.0] fault > > addr 204865000, iommu reg = ffff82c3fff57000 > > (XEN) DMAR:[fault reason 02h] Present bit in context entry is clear > > (XEN) print_vtd_entries: iommu = ffff83013fffaee0 bdf = 5:8.0 gmfn > > 204865 > > (XEN) root_entry = ffff83013ff37000 > > (XEN) root_entry[5] = 13cf12001 > > (XEN) context = ffff83013cf12000 > > (XEN) context[40] = 0_0 > > (XEN) ctxt_entry[40] not present > > (XEN) [VT-D]iommu.c:821: iommu_fault_status: Primary Pending Fault > > (XEN) [VT-D]iommu.c:796: DMAR:[DMA Write] Request device [05:08.0] fault > > addr 2074be000, iommu reg = ffff82c3fff57000 > > (XEN) DMAR:[fault reason 02h] Present bit in context entry is clear > > (XEN) print_vtd_entries: iommu = ffff83013fffaee0 bdf = 5:8.0 gmfn > > 2074be > > (XEN) root_entry = ffff83013ff37000 > > (XEN) root_entry[5] = 13cf12001 > > (XEN) context = ffff83013cf12000 > > (XEN) context[40] = 0_0 > > (XEN) ctxt_entry[40] not present > > > > (XEN) [VT-D]iommu.c:796: DMAR:[DMA Write] Request device [05:08.0] fault > > addr 204865000, iommu reg = ffff82c3fff57000 > > (XEN) DMAR:[fault reason 02h] Present bit in context entry is clear > > (XEN) print_vtd_entries: iommu = ffff83013fffaee0 bdf = 5:8.0 gmfn > > 204865 > > (XEN) root_entry = ffff83013ff37000 > > (XEN) root_entry[5] = 13cf12001 > > (XEN) context = ffff83013cf12000 > > (XEN) context[40] = 0_0 > > (XEN) ctxt_entry[40] not present > > (XEN) [VT-D]iommu.c:821: iommu_fault_status: Primary Pending Fault > > (XEN) [VT-D]iommu.c:796: DMAR:[DMA Write] Request device [05:08.0] fault > > addr 2074be000, iommu reg = ffff82c3fff57000 > > (XEN) DMAR:[fault reason 02h] Present bit in context entry is clear > > (XEN) print_vtd_entries: iommu = ffff83013fffaee0 bdf = 5:8.0 gmfn > > 2074be > > (XEN) root_entry = ffff83013ff37000 > > (XEN) root_entry[5] = 13cf12001 > > (XEN) context = ffff83013cf12000 > > (XEN) context[40] = 0_0 > > (XEN) ctxt_entry[40] not present > > > > (XEN) context[40] = 0_0 > > (XEN) ctxt_entry[40] not present > > (XEN) [VT-D]iommu.c:796: DMAR:[DMA Write] Request device [05:08.0] fault > > addr 204865000, iommu reg = ffff82c3fff57000 > > (XEN) DMAR:[fault reason 02h] Present bit in context entry is clear > > (XEN) print_vtd_entries: iommu = ffff83013fffaee0 bdf = 5:8.0 gmfn > > 204865 > > (XEN) root_entry = ffff83013ff37000 > > (XEN) root_entry[5] = 13cf12001 > > (XEN) context = ffff83013cf12000 > > (XEN) context[40] = 0_0 > > (XEN) ctxt_entry[40] not present > > (XEN) [VT-D]iommu.c:821: iommu_fault_status: Primary Pending Fault > > (XEN) [VT-D]iommu.c:796: DMAR:[DMA Write] Request device [05:08.0] fault > > addr 2074be000, iommu reg = ffff82c3fff57000 > > (XEN) DMAR:[fault reason 02h] Present bit in context entry is clear > > (XEN) print_vtd_entries: iommu = ffff83013fffaee0 bdf = 5:8.0 gmfn > > 2074be > > (XEN) root_entry = ffff83013ff37000 > > (XEN) root_entry[5] = 13cf12001 > > (XEN) context = ffff83013cf12000 > > (XEN) context[40] = 0_0 > > (XEN) ctxt_entry[40] not present > > > > (XEN) context[40] = 0_0 > > (XEN) ctxt_entry[40] not present > > (XEN) [VT-D]iommu.c:796: DMAR:[DMA Write] Request device [05:08.0] fault > > addr 204865000, iommu reg = ffff82c3fff57000 > > (XEN) DMAR:[fault reason 02h] Present bit in context entry is clear > > (XEN) print_vtd_entries: iommu = ffff83013fffaee0 bdf = 5:8.0 gmfn > > 204865 > > (XEN) root_entry = ffff83013ff37000 > > (XEN) root_entry[5] = 13cf12001 > > (XEN) context = ffff83013cf12000 > > (XEN) context[40] = 0_0 > > (XEN) ctxt_entry[40] not present > > (XEN) [VT-D]iommu.c:821: iommu_fault_status: Primary Pending Fault > > (XEN) [VT-D]iommu.c:796: DMAR:[DMA Write] Request device [05:08.0] fault > > addr 2074be000, iommu reg = ffff82c3fff57000 > > (XEN) DMAR:[fault reason 02h] Present bit in context entry is clear > > (XEN) print_vtd_entries: iommu = ffff83013fffaee0 bdf = 5:8.0 gmfn > > 2074be > > (XEN) root_entry = ffff83013ff37000 > > (XEN) root_entry[5] = 13cf12001 > > (XEN) context = ffff83013cf12000 > > (XEN) context[40] = 0_0 > > (XEN) ctxt_entry[40] not present > > > > (XEN) context[40] = 0_0 > > (XEN) ctxt_entry[40] not present > > (XEN) [VT-D]iommu.c:796: DMAR:[DMA Write] Request device [05:08.0] fault > > addr 204865000, iommu reg = ffff82c3fff57000 > > (XEN) DMAR:[fault reason 02h] Present bit in context entry is clear > > (XEN) print_vtd_entries: iommu = ffff83013fffaee0 bdf = 5:8.0 gmfn > > 204865 > > (XEN) root_entry = ffff83013ff37000 > > (XEN) root_entry[5] = 13cf12001 > > (XEN) context = ffff83013cf12000 > > (XEN) context[40] = 0_0 > > (XEN) ctxt_entry[40] not present > > (XEN) [VT-D]iommu.c:821: iommu_fault_status: Primary Pending Fault > > (XEN) [VT-D]iommu.c:796: DMAR:[DMA Write] Request device [05:08.0] fault > > addr 2074be000, iommu reg = ffff82c3fff57000 > > (XEN) DMAR:[fault reason 02h] Present bit in context entry is clear > > (XEN) print_vtd_entries: iommu = ffff83013fffaee0 bdf = 5:8.0 gmfn > > 2074be > > (XEN) root_entry = ffff83013ff37000 > > (XEN) root_entry[5] = 13cf12001 > > (XEN) context = ffff83013cf12000 > > (XEN) context[40] = 0_0 > > (XEN) ctxt_entry[40] not present > > > > (XEN) context[40] = 0_0 > > (XEN) ctxt_entry[40] not present > > (XEN) [VT-D]iommu.c:796: DMAR:[DMA Write] Request device [05:08.0] fault > > addr 204865000, iommu reg = ffff82c3fff57000 > > (XEN) DMAR:[fault reason 02h] Present bit in context entry is clear > > (XEN) print_vtd_entries: iommu = ffff83013fffaee0 bdf = 5:8.0 gmfn > > 204865 > > (XEN) root_entry = ffff83013ff37000 > > (XEN) root_entry[5] = 13cf12001 > > (XEN) context = ffff83013cf12000 > > (XEN) context[40] = 0_0 > > (XEN) ctxt_entry[40] not present > > (XEN) [VT-D]iommu.c:821: iommu_fault_status: Primary Pending Fault > > (XEN) [VT-D]iommu.c:796: DMAR:[DMA Write] Request device [05:08.0] fault > > addr 2074be000, iommu reg = ffff82c3fff57000 > > (XEN) DMAR:[fault reason 02h] Present bit in context entry is clear > > (XEN) print_vtd_entries: iommu = ffff83013fffaee0 bdf = 5:8.0 gmfn > > 2074be > > (XEN) root_entry = ffff83013ff37000 > > (XEN) root_entry[5] = 13cf12001 > > (XEN) context = ffff83013cf12000 > > (XEN) context[40] = 0_0 > > (XEN) ctxt_entry[40] not present > > > > > > _______________________________________________ > > Xen-devel mailing list > > Xen-devel@lists.xensource.com > > http://lists.xensource.com/xen-devel_______________________________________________ Xen-devel mailing list Xen-devel@lists.xensource.com http://lists.xensource.com/xen-devel _______________________________________________ Xen-devel mailing list Xen-devel@lists.xensource.com http://lists.xensource.com/xen-devel
Weidong Han
2010-Jun-02 01:23 UTC
Re: [Xen-devel] iommuu/vt-d issues with LSI MegaSAS (PERC5i)
This PCI-x card is not suitable for assignment. It contains an invisible device 05:08.0 (lspci cannot show it), but this invisible device won''t be mapped by VT-d because VT-d engine doesn''t know this device, so you can see the DMAR faults on it. One workaround is to hard code to map 05:08.0 when assign 05:0e.0. BTW, PCIe LSI card don''t have this problem. Regards, Weidong M. Nunberg wrote:> I''ve been trying to get VT-D working wiht xen for quite some time, since > 3.4.2, and I''ve always had issues with my RAID controller not working > properly when iommu is not disabled in Xen: > > lspci outpuut for the card: > 05:0e.0 RAID bus controller: Dell PowerEdge Expandable RAID controller 5 > Subsystem: Dell PERC 5/i Integrated RAID Controller > Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- > Stepping+ SERR- FastB2B- DisINTx- > Status: Cap+ 66MHz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- > <TAbort- <MAbort- >SERR- <PERR- INTx- > Latency: 64 (32000ns min), Cache Line Size: 64 bytes > Interrupt: pin A routed to IRQ 18 > Region 0: Memory at f2ff0000 (32-bit, prefetchable) [size=64K] > Region 2: Memory at fbce0000 (32-bit, non-prefetchable) [size=128K] > Expansion ROM at fbcd0000 [disabled] [size=32K] > Capabilities: [c0] Power Management version 2 > Flags: PMEClk- DSI- D1+ D2- AuxCurrent=0mA > PME(D0-,D1-,D2-,D3hot-,D3cold-) > Status: D0 PME-Enable- DSel=0 DScale=0 PME- > Capabilities: [d0] Message Signalled Interrupts: Mask- 64bit+ Queue=0/1 > Enable- > Address: 0000000000000000 Data: 0000 > Capabilities: [e0] PCI-X non-bridge device > Command: DPERE- ERO- RBC=512 OST=4 > Status: Dev=05:0e.0 64bit+ 133MHz+ SCD- USC- DC=bridge DMMRBC=1024 > DMOST=4 DMCRS=16 RSCEM- 266MHz- 533MHz- > Kernel driver in use: megaraid_sas > Kernel modules: megaraid_sas > > I am using a Supermicro X8DALi motherboard with a 5500 chipset. > > Whenever I try to access the device the Xen console spits out something > like this: > (XEN) [VT-D]iommu.c:796: DMAR:[DMA Write] Request device [05:08.0] fault > addr 204865000, iommu reg = ffff82c3fff57000 > (XEN) DMAR:[fault reason 02h] Present bit in context entry is clear > (XEN) print_vtd_entries: iommu = ffff83013fffaee0 bdf = 5:8.0 gmfn > 204865 > (XEN) root_entry = ffff83013ff37000 > (XEN) root_entry[5] = 13cf12001 > (XEN) context = ffff83013cf12000 > (XEN) context[40] = 0_0 > (XEN) ctxt_entry[40] not present > (XEN) [VT-D]iommu.c:821: iommu_fault_status: Primary Pending Fault > > reads are partially succcessful, but I am getting seek errors at times, > filesystems will mount properly but I cannot use any of them properly.. > > > The actual kernel output varies, sometimes i get EINVAL when I try to > read from the filesystem, sometimes it simply refuses to at all > recognize the disk altogether, and other times it will hang the entire > system, including the hypervisor itself. > I''ve tried booting the hypervisor with x2apic disabled, but to no > effect. I''ve also tried with the latest xen-4.0-testing (4.0.1), buut > same issue and same outpuut > > A quick google turns up a thread, from this mailing list, with a > different RAID card, but the kernel output is similar.. e.g. > > scsi scan: INQUIRY result too short (5), using 36 > > http://lists.xensource.com/archives/html/xen-users/2010-04/msg00535.html > > The full xen log is below > > > > L __ __ _ _ ___ > ___ > \ \/ /___ _ __ | || | / _ \ / _ \ 0x146000>, shtab=0x3a2078, > entry=0x100000 > \ // _ \ ''_ \ | || |_| | | | | | > | > / \ __/ | | | |__ _| |_| | |_| |apper/OS-root ro nomodeset > console=tty0 r > /_/\_\___|_| |_| | > _|(_)___(_)___/ > 020 > bytes] > (XEN) Xen version 4.0.0 (mordy@) (gcc version 4.3.2 (Debian 4.3.2-1.1) ) > Fri May 21 07:50:16 PDT 2010boot-module > @ > (XEN) Latest ChangeSet: > unavailable > (XEN) Console output is > synchronous. > (XEN) Command line: iommu=verbose loglvl=all guest_loglvl=all > sync_console console_to_rint com1=115200,8n1 > console=com1 > (XEN) Video > information: > (XEN) VGA is text mode 80x25, font > 8x16 > (XEN) VBE/DDC methods: none; EDID transfer time: 0 > seconds > (XEN) EDID info not retrieved because no DDC retrieval method > detected > (XEN) Disc information: > (XEN) Found 1 MBR signatures > (XEN) Found 1 EDD information structures > (XEN) Xen-e820 RAM map: > (XEN) 0000000000000000 - 000000000009a000 (usable) > (XEN) 000000000009a000 - 00000000000a0000 (reserved) > (XEN) 00000000000e0000 - 0000000000100000 (reserved) > (XEN) 0000000000100000 - 00000000bf760000 (usable) > (XEN) 00000000bf76e000 - 00000000bf770000 type 9 > (XEN) 00000000bf770000 - 00000000bf77e000 (ACPI data) > (XEN) 00000000bf77e000 - 00000000bf7d0000 (ACPI NVS) > (XEN) 00000000bf7d0000 - 00000000bf7e0000 (reserved) > (XEN) 00000000bf7ec000 - 00000000c0000000 (reserved) > (XEN) 00000000fee00000 - 00000000fee01000 (reserved) > (XEN) 00000000ffc00000 - 0000000100000000 (reserved) > (XEN) 0000000100000000 - 0000000340000000 (usable) > (XEN) ACPI: RSDP 000F9E10, 0024 (r2 ACPIAM) > (XEN) ACPI: XSDT BF770100, 0094 (r1 NEC 20090424 MSFT > 97) > (XEN) ACPI: FACP BF770290, 00F4 (r4 042409 FACP1917 20090424 MSFT > 97) > (XEN) ACPI: DSDT BF770670, 5BFB (r2 10601 10601000 0 INTL > 20051117) > (XEN) ACPI: FACS BF77E000, 0040 > (XEN) ACPI: APIC BF770390, 00D2 (r2 042409 APIC1917 20090424 MSFT > 97) > (XEN) ACPI: MCFG BF770470, 003C (r1 042409 OEMMCFG 20090424 MSFT > 97) > (XEN) ACPI: SLIC BF7704B0, 0176 (r1 NEC 20090424 MSFT > 97) > (XEN) ACPI: ERST BF770630, 0040 (r1 042409 WHEA1917 20090424 MSFT > 97) > (XEN) ACPI: OEMB BF77E040, 007B (r1 042409 OEMB1917 20090424 MSFT > 97) > (XEN) ACPI: SRAT BF77A670, 01D0 (r1 042409 OEMSRAT 1 INTL > 1) > (XEN) ACPI: HPET BF77A840, 0038 (r1 042409 OEMHPET 20090424 MSFT > 97) > (XEN) ACPI: DMAR BF77E0C0, 0118 (r1 AMI OEMDMAR 1 MSFT > 97) > (XEN) ACPI: SSDT BF781DF0, 0363 (r1 DpgPmm CpuPm 12 INTL > 20051117) > (XEN) ACPI: EINJ BF77A880, 0130 (r1 AMIER AMI_EINJ 20090424 MSFT > 97) > (XEN) ACPI: BERT BF77AA10, 0030 (r1 AMIER AMI_BERT 20090424 MSFT > 97) > (XEN) ACPI: ERST BF77AA40, 01B0 (r1 AMIER AMI_ERST 20090424 MSFT > 97) > (XEN) ACPI: HEST BF77ABF0, 00A8 (r1 AMIER AMI_HEST 20090424 MSFT > 97) > (XEN) System RAM: 12045MB (12334808kB) > (XEN) SRAT: PXM 0 -> APIC 0 -> Node 0 > (XEN) SRAT: PXM 0 -> APIC 2 -> Node 0 > (XEN) SRAT: PXM 0 -> APIC 4 -> Node 0 > (XEN) SRAT: PXM 0 -> APIC 6 -> Node 0 > (XEN) SRAT: PXM 0 -> APIC 1 -> Node 0 > (XEN) SRAT: PXM 0 -> APIC 3 -> Node 0 > (XEN) SRAT: PXM 0 -> APIC 5 -> Node 0 > (XEN) SRAT: PXM 0 -> APIC 7 -> Node 0 > (XEN) SRAT: PXM 1 -> APIC 16 -> Node 1 > (XEN) SRAT: PXM 1 -> APIC 18 -> Node 1 > (XEN) SRAT: PXM 1 -> APIC 20 -> Node 1 > (XEN) SRAT: PXM 1 -> APIC 22 -> Node 1 > (XEN) SRAT: PXM 1 -> APIC 17 -> Node 1 > (XEN) SRAT: PXM 1 -> APIC 19 -> Node 1 > (XEN) SRAT: PXM 1 -> APIC 21 -> Node 1 > (XEN) SRAT: PXM 1 -> APIC 23 -> Node 1 > (XEN) SRAT: Node 0 PXM 0 0-a0000 > (XEN) SRAT: Node 0 PXM 0 100000-c0000000 > (XEN) SRAT: Node 0 PXM 0 100000000-1c0000000 > (XEN) SRAT: Node 1 PXM 1 1c0000000-340000000 > (XEN) NUMA: Allocated memnodemap from 33fdfb000 - 33fdff000 > (XEN) NUMA: Using 8 for the hash shift. > (XEN) Domain heap initialised DMA width 30 bits > (XEN) found SMP MP-table at 000ff780 > (XEN) DMI present. > (XEN) Using APIC driver default > (XEN) ACPI: PM-Timer IO Port: 0x808 > (XEN) ACPI: ACPI SLEEP INFO: pm1x_cnt[804,0], pm1x_evt[800,0] > (XEN) ACPI: wakeup_vec[bf77e00c], vec_size[20] > (XEN) ACPI: Local APIC address 0xfee00000 > (XEN) ACPI: LAPIC (acpi_id[0x01] lapic_id[0x00] enabled) > (XEN) Processor #0 7:10 APIC version 21 > (XEN) ACPI: LAPIC (acpi_id[0x02] lapic_id[0x10] enabled) > (XEN) Processor #16 7:10 APIC version 21 > (XEN) ACPI: LAPIC (acpi_id[0x03] lapic_id[0x02] enabled) > (XEN) Processor #2 7:10 APIC version 21 > (XEN) ACPI: LAPIC (acpi_id[0x04] lapic_id[0x12] enabled) > (XEN) Processor #18 7:10 APIC version 21 > (XEN) ACPI: LAPIC (acpi_id[0x05] lapic_id[0x04] enabled) > (XEN) Processor #4 7:10 APIC version 21 > (XEN) ACPI: LAPIC (acpi_id[0x06] lapic_id[0x14] enabled) > (XEN) Processor #20 7:10 APIC version 21 > (XEN) ACPI: LAPIC (acpi_id[0x07] lapic_id[0x06] enabled) > (XEN) Processor #6 7:10 APIC version 21 > (XEN) ACPI: LAPIC (acpi_id[0x08] lapic_id[0x16] enabled) > (XEN) Processor #22 7:10 APIC version 21 > (XEN) ACPI: LAPIC (acpi_id[0x09] lapic_id[0x01] enabled) > (XEN) Processor #1 7:10 APIC version 21 > (XEN) ACPI: LAPIC (acpi_id[0x0a] lapic_id[0x11] enabled) > (XEN) Processor #17 7:10 APIC version 21 > (XEN) ACPI: LAPIC (acpi_id[0x0b] lapic_id[0x03] enabled) > (XEN) Processor #3 7:10 APIC version 21 > (XEN) ACPI: LAPIC (acpi_id[0x0c] lapic_id[0x13] enabled) > (XEN) Processor #19 7:10 APIC version 21 > (XEN) ACPI: LAPIC (acpi_id[0x0d] lapic_id[0x05] enabled) > (XEN) Processor #5 7:10 APIC version 21 > (XEN) ACPI: LAPIC (acpi_id[0x0e] lapic_id[0x15] enabled) > (XEN) Processor #21 7:10 APIC version 21 > (XEN) ACPI: LAPIC (acpi_id[0x0f] lapic_id[0x07] enabled) > (XEN) Processor #7 7:10 APIC version 21 > (XEN) ACPI: LAPIC (acpi_id[0x10] lapic_id[0x17] enabled) > (XEN) Processor #23 7:10 APIC version 21 > (XEN) ACPI: LAPIC_NMI (acpi_id[0xff] dfl dfl lint[0x1]) > (XEN) Overriding APIC driver with bigsmp > (XEN) ACPI: IOAPIC (id[0x08] address[0xfec00000] gsi_base[0]) > (XEN) IOAPIC[0]: apic_id 8, version 32, address 0xfec00000, GSI 0-23 > (XEN) ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl) > (XEN) ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 20 low level) > (XEN) ACPI: IRQ0 used by override. > (XEN) ACPI: IRQ2 used by override. > (XEN) ACPI: IRQ9 used by override. > (XEN) Enabling APIC mode: Phys. Using 1 I/O APICs > (XEN) ACPI: HPET id: 0xffffffff base: 0xfed00000 > (XEN) [VT-D]dmar.c:679: Host address width 40 > (XEN) [VT-D]dmar.c:694: found ACPI_DMAR_DRHD: > (XEN) [VT-D]dmar.c:398: dmaru->address = fbffe000 > (XEN) [VT-D]dmar.c:340: IOAPIC: f0:1f.7 > (XEN) [VT-D]dmar.c:411: flags: INCLUDE_ALL > (XEN) [VT-D]dmar.c:699: found ACPI_DMAR_RMRR: > (XEN) [VT-D]dmar.c:334: endpoint: 0:1d.0 > (XEN) [VT-D]dmar.c:334: endpoint: 0:1d.1 > (XEN) [VT-D]dmar.c:334: endpoint: 0:1d.2 > (XEN) [VT-D]dmar.c:334: endpoint: 0:1d.7 > (XEN) [VT-D]dmar.c:334: endpoint: 0:1a.0 > (XEN) [VT-D]dmar.c:334: endpoint: 0:1a.1 > (XEN) [VT-D]dmar.c:334: endpoint: 0:1a.2 > (XEN) [VT-D]dmar.c:334: endpoint: 0:1a.7 > (XEN) [VT-D]dmar.c:571: RMRR region: base_addr ec000 end_address effff > (XEN) [VT-D]dmar.c:699: found ACPI_DMAR_RMRR: > (XEN) [VT-D]dmar.c:334: endpoint: 0:1d.0 > (XEN) [VT-D]dmar.c:334: endpoint: 0:1d.1 > (XEN) [VT-D]dmar.c:334: endpoint: 0:1d.2 > (XEN) [VT-D]dmar.c:334: endpoint: 0:1d.7 > (XEN) [VT-D]dmar.c:334: endpoint: 0:1a.0 > (XEN) [VT-D]dmar.c:334: endpoint: 0:1a.1 > (XEN) [VT-D]dmar.c:334: endpoint: 0:1a.2 > (XEN) [VT-D]dmar.c:334: endpoint: 0:1a.7 > (XEN) [VT-D]dmar.c:571: RMRR region: base_addr bf7ec000 end_address > bf7fffff > (XEN) [VT-D]dmar.c:704: found ACPI_DMAR_ATSR: > (XEN) [VT-D]dmar.c:599: atsru->all_ports: 0 > (XEN) [VT-D]dmar.c:320: bridge: 0:1.0 start = 0 sec = 1 sub = 1 > (XEN) [VT-D]dmar.c:320: bridge: 0:3.0 start = 0 sec = 2 sub = 2 > (XEN) [VT-D]dmar.c:320: bridge: 0:7.0 start = 0 sec = 3 sub = 3 > (XEN) PCI: MCFG configuration 0: base e0000000 segment 0 buses 0 - 255 > (XEN) PCI: Not using MMCONFIG. > (XEN) Using ACPI (MADT) for SMP configuration information > (XEN) Using scheduler: SMP Credit Scheduler (credit) > (XEN) Detected 2266.790 MHz processor. > (XEN) Initing memory sharing. > (XEN) VMX: Supported advanced features: > (XEN) - APIC MMIO access virtualisation > (XEN) - APIC TPR shadow > (XEN) - Extended Page Tables (EPT) > (XEN) - Virtual-Processor Identifiers (VPID) > (XEN) - Virtual NMI > (XEN) - MSR direct-access bitmap > (XEN) HVM: ASIDs enabled. > (XEN) HVM: VMX enabled > (XEN) HVM: Hardware Assisted Paging detected. > (XEN) Intel machine check reporting enabled > (XEN) [VT-D]iommu.c:1078: drhd->address = fbffe000 iommu->reg > ffff82c3fff57000 > (XEN) [VT-D]iommu.c:1080: cap = c90780106f0462 ecap = f0207e > (XEN) Intel VT-d Snoop Control not supported. > (XEN) Intel VT-d DMA Passthrough not supported. > (XEN) Intel VT-d Queued Invalidation supported. > (XEN) Intel VT-d Interrupt Remapping supported. > (XEN) I/O virtualisation enabled > (XEN) I/O virtualisation for PV guests disabled > (XEN) Total of 16 processors activated. > (XEN) ENABLING IO-APIC IRQs > (XEN) -> Using new ACK method > (XEN) ..TIMER: vector=0xF0 apic1=0 pin1=2 apic2=-1 pin2=-1 > (XEN) TSC is reliable, synchronization unnecessary > (XEN) Platform timer is 14.318MHz HPET > ?(XEN) Allocated console ring of 128 KiB. > (XEN) microcode.c:73:d32767 microcode: CPU1 resumed > (XEN) microcode.c:73:d32767 microcode: CPU9 resumed > (XEN) microcode.c:73:d32767 microcode: CPU14 resumed > (XEN) microcode.c:73:d32767 microcode: CPU6 resumed > (XEN) microcode.c:73:d32767 microcode: CPU3 resumed > (XEN) microcode.c:73:d32767 microcode: CPU11 resumed > (XEN) microcode.c:73:d32767 microcode: CPU8 resumed > (XEN) microcode.c:73:d32767 microcode: CPU7 resumed > (XEN) microcode.c:73:d32767 microcode: CPU15 resumed > (XEN) microcode.c:73:d32767 microcode: CPU2 resumed > (XEN) microcode.c:73:d32767 microcode: CPU5 resumed > (XEN) microcode.c:73:d32767 microcode: CPU13 resumed > (XEN) microcode.c:73:d32767 microcode: CPU4 resumed > (XEN) microcode.c:73:d32767 microcode: CPU10 resumed > (XEN) Brought up 16 CPUs > (XEN) microcode.c:73:d32767 microcode: CPU12 resumed > (XEN) Turbo Mode detected! > (XEN) HPET''s MSI mode hasn''t been supported when Interrupt Remapping is > enabled. > (XEN) ACPI sleep modes: S3 > (XEN) mcheck_poll: Machine check polling timer started. > (XEN) [VT-D]iommu.c:1325: d0:PCIe: map bdf = 0:0.0 > (XEN) [VT-D]iommu.c:1325: d0:PCIe: map bdf = 0:14.0 > (XEN) [VT-D]iommu.c:1325: d0:PCIe: map bdf = 0:14.1 > (XEN) [VT-D]iommu.c:1325: d0:PCIe: map bdf = 0:14.2 > (XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = 0:14.3 > (XEN) [VT-D]iommu.c:1325: d0:PCIe: map bdf = 0:16.0 > (XEN) [VT-D]iommu.c:1325: d0:PCIe: map bdf = 0:16.1 > (XEN) [VT-D]iommu.c:1325: d0:PCIe: map bdf = 0:16.2 > (XEN) [VT-D]iommu.c:1325: d0:PCIe: map bdf = 0:16.3 > (XEN) [VT-D]iommu.c:1325: d0:PCIe: map bdf = 0:16.4 > (XEN) [VT-D]iommu.c:1325: d0:PCIe: map bdf = 0:16.5 > (XEN) [VT-D]iommu.c:1325: d0:PCIe: map bdf = 0:16.6 > (XEN) [VT-D]iommu.c:1325: d0:PCIe: map bdf = 0:16.7 > (XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = 0:1a.0 > (XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = 0:1a.1 > (XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = 0:1a.2 > (XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = 0:1a.7 > (XEN) [VT-D]iommu.c:1325: d0:PCIe: map bdf = 0:1b.0 > (XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = 0:1d.0 > (XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = 0:1d.1 > (XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = 0:1d.2 > (XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = 0:1d.7 > (XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = 0:1f.0 > (XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = 0:1f.2 > (XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = 0:1f.3 > (XEN) [VT-D]iommu.c:1325: d0:PCIe: map bdf = 1:0.0 > (XEN) [VT-D]iommu.c:1325: d0:PCIe: map bdf = 3:0.0 > (XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = 5:e.0 > (XEN) [VT-D]iommu.c:1325: d0:PCIe: map bdf = 7:0.0 > (XEN) [VT-D]iommu.c:1325: d0:PCIe: map bdf = 8:0.0 > (XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = fe:0.0 > (XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = fe:0.1 > (XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = fe:2.0 > (XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = fe:2.1 > (XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = fe:2.4 > (XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = fe:2.5 > (XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = fe:3.0 > (XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = fe:3.1 > (XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = fe:3.2 > (XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = fe:3.4 > (XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = fe:4.0 > (XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = fe:4.1 > (XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = fe:4.2 > (XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = fe:4.3 > (XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = fe:5.0 > (XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = fe:5.1 > (XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = fe:5.2 > (XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = fe:5.3 > (XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = fe:6.0 > (XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = fe:6.1 > (XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = fe:6.2 > (XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = fe:6.3 > (XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = ff:0.0 > (XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = ff:0.1 > (XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = ff:2.0 > (XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = ff:2.1 > (XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = ff:2.4 > (XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = ff:2.5 > (XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = ff:3.0 > (XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = ff:3.1 > (XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = ff:3.2 > (XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = ff:3.4 > (XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = ff:4.0 > (XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = ff:4.1 > (XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = ff:4.2 > (XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = ff:4.3 > (XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = ff:5.0 > (XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = ff:5.1 > (XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = ff:5.2 > (XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = ff:5.3 > (XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = ff:6.0 > (XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = ff:6.1 > (XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = ff:6.2 > (XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = ff:6.3 > (XEN) [VT-D]iommu.c:695: iommu_enable_translation: iommu->reg > ffff82c3fff57000 > (XEN) *** LOADING DOMAIN 0 *** > (XEN) Xen kernel: 64-bit, lsb, compat32 > (XEN) Dom0 kernel: 64-bit, PAE, lsb, paddr 0x1000000 -> 0x26b6000 > (XEN) PHYSICAL MEMORY ARRANGEMENT: > (XEN) Dom0 alloc.: 0000000100000000->0000000120000000 (2937045 pages > to be allocated) > (XEN) VIRTUAL MEMORY ARRANGEMENT: > (XEN) Loaded kernel: ffffffff81000000->ffffffff826b6000 > (XEN) Init. ramdisk: ffffffff826b6000->ffffffff8f7d7600 > (XEN) Phys-Mach map: ffffffff8f7d8000->ffffffff90f406a8 > (XEN) Start info: ffffffff90f41000->ffffffff90f414b4 > (XEN) Page tables: ffffffff90f42000->ffffffff90fcf000 > (XEN) Boot stack: ffffffff90fcf000->ffffffff90fd0000 > (XEN) TOTAL: ffffffff80000000->ffffffff91400000 > (XEN) ENTRY ADDRESS: ffffffff819be200 > (XEN) Dom0 has maximum 16 VCPUs > (XEN) Scrubbing Free RAM: .done. > (XEN) Xen trace buffers: disabled > (XEN) Std. Loglevel: All > (XEN) Guest Loglevel: All > (XEN) ********************************************** > (XEN) ******* WARNING: CONSOLE OUTPUT IS SYNCHRONOUS > (XEN) ******* This option is intended to aid debugging of Xen by > ensuring > (XEN) ******* that all output is synchronously delivered on the serial > line. > (XEN) ******* However it can introduce SIGNIFICANT latencies and affect > (XEN) ******* timekeeping. It is NOT recommended for production use! > (XEN) ********************************************** > (XEN) 3... 2... 1... > (XEN) *** Serial input -> DOM0 (type ''CTRL-a'' three times to switch > input to Xen) > (XEN) Freed 164kB init memory. > mapping kernel into physical memory > Xen: setup ISA identity maps > about to get started... > (XEN) PCI add device 00:00.0 > (XEN) PCI add device 00:01.0 > (XEN) PCI add device 00:03.0 > (XEN) PCI add device 00:07.0 > (XEN) PCI add device 00:14.0 > (XEN) PCI add device 00:14.1 > (XEN) PCI add device 00:14.2 > (XEN) PCI add device 00:14.3 > (XEN) PCI add device 00:16.0 > (XEN) PCI add device 00:16.1 > (XEN) PCI add device 00:16.2 > (XEN) PCI add device 00:16.3 > (XEN) PCI add device 00:16.4 > (XEN) PCI add device 00:16.5 > (XEN) PCI add device 00:16.6 > (XEN) PCI add device 00:16.7 > (XEN) PCI add device 00:1a.0 > (XEN) PCI add device 00:1a.1 > (XEN) PCI add device 00:1a.2 > (XEN) PCI add device 00:1a.7 > (XEN) PCI add device 00:1b.0 > (XEN) PCI add device 00:1c.0 > (XEN) PCI add device 00:1c.4 > (XEN) PCI add device 00:1c.5 > (XEN) PCI add device 00:1d.0 > (XEN) PCI add device 00:1d.1 > (XEN) PCI add device 00:1d.2 > (XEN) PCI add device 00:1d.7 > (XEN) PCI add device 00:1e.0 > (XEN) PCI add device 00:1f.0 > (XEN) PCI add device 00:1f.2 > (XEN) PCI add device 00:1f.3 > (XEN) PCI add device 01:00.0 > (XEN) PCI add device 03:00.0 > (XEN) PCI add device 04:00.0 > (XEN) PCI add device 04:00.2 > (XEN) PCI add device 05:0e.0 > (XEN) PCI add device 07:00.0 > (XEN) PCI add device 08:00.0 > (XEN) cpuid.MWAIT[.eax=40, .ebx=40, .ecx=3, .edx=1120] > (XEN) Monitor-Mwait will be used to enter C-1 state > (XEN) cpuid.MWAIT[.eax=40, .ebx=40, .ecx=3, .edx=1120] > (XEN) Monitor-Mwait will be used to enter C-3 state > (XEN) cpuid.MWAIT[.eax=40, .ebx=40, .ecx=3, .edx=1120] > (XEN) Monitor-Mwait will be used to enter C-3 state > (XEN) cpuid.MWAIT[.eax=40, .ebx=40, .ecx=3, .edx=1120] > (XEN) Monitor-Mwait will be used to enter C-1 state > (XEN) cpuid.MWAIT[.eax=40, .ebx=40, .ecx=3, .edx=1120] > (XEN) Monitor-Mwait will be used to enter C-3 state > (XEN) cpuid.MWAIT[.eax=40, .ebx=40, .ecx=3, .edx=1120] > (XEN) Monitor-Mwait will be used to enter C-3 state > (XEN) cpuid.MWAIT[.eax=40, .ebx=40, .ecx=3, .edx=1120] > (XEN) Monitor-Mwait will be used to enter C-1 state > (XEN) cpuid.MWAIT[.eax=40, .ebx=40, .ecx=3, .edx=1120] > (XEN) Monitor-Mwait will be used to enter C-3 state > (XEN) cpuid.MWAIT[.eax=40, .ebx=40, .ecx=3, .edx=1120] > (XEN) Monitor-Mwait will be used to enter C-3 state > (XEN) cpuid.MWAIT[.eax=40, .ebx=40, .ecx=3, .edx=1120] > (XEN) Monitor-Mwait will be used to enter C-1 state > (XEN) cpuid.MWAIT[.eax=40, .ebx=40, .ecx=3, .edx=1120] > (XEN) Monitor-Mwait will be used to enter C-3 state > (XEN) cpuid.MWAIT[.eax=40, .ebx=40, .ecx=3, .edx=1120] > (XEN) Monitor-Mwait will be used to enter C-3 state > (XEN) cpuid.MWAIT[.eax=40, .ebx=40, .ecx=3, .edx=1120] > (XEN) Monitor-Mwait will be used to enter C-1 state > (XEN) cpuid.MWAIT[.eax=40, .ebx=40, .ecx=3, .edx=1120] > (XEN) Monitor-Mwait will be used to enter C-3 state > (XEN) cpuid.MWAIT[.eax=40, .ebx=40, .ecx=3, .edx=1120] > (XEN) Monitor-Mwait will be used to enter C-3 state > (XEN) cpuid.MWAIT[.eax=40, .ebx=40, .ecx=3, .edx=1120] > (XEN) Monitor-Mwait will be used to enter C-1 state > (XEN) cpuid.MWAIT[.eax=40, .ebx=40, .ecx=3, .edx=1120] > (XEN) Monitor-Mwait will be used to enter C-3 state > (XEN) cpuid.MWAIT[.eax=40, .ebx=40, .ecx=3, .edx=1120] > (XEN) Monitor-Mwait will be used to enter C-3 state > (XEN) cpuid.MWAIT[.eax=40, .ebx=40, .ecx=3, .edx=1120] > (XEN) Monitor-Mwait will be used to enter C-1 state > (XEN) cpuid.MWAIT[.eax=40, .ebx=40, .ecx=3, .edx=1120] > (XEN) Monitor-Mwait will be used to enter C-3 state > (XEN) cpuid.MWAIT[.eax=40, .ebx=40, .ecx=3, .edx=1120] > (XEN) Monitor-Mwait will be used to enter C-3 state > (XEN) cpuid.MWAIT[.eax=40, .ebx=40, .ecx=3, .edx=1120] > (XEN) Monitor-Mwait will be used to enter C-1 state > (XEN) cpuid.MWAIT[.eax=40, .ebx=40, .ecx=3, .edx=1120] > (XEN) Monitor-Mwait will be used to enter C-3 state > (XEN) cpuid.MWAIT[.eax=40, .ebx=40, .ecx=3, .edx=1120] > (XEN) Monitor-Mwait will be used to enter C-3 state > (XEN) cpuid.MWAIT[.eax=40, .ebx=40, .ecx=3, .edx=1120] > (XEN) Monitor-Mwait will be used to enter C-1 state > (XEN) cpuid.MWAIT[.eax=40, .ebx=40, .ecx=3, .edx=1120] > (XEN) Monitor-Mwait will be used to enter C-3 state > (XEN) cpuid.MWAIT[.eax=40, .ebx=40, .ecx=3, .edx=1120] > (XEN) Monitor-Mwait will be used to enter C-3 state > (XEN) cpuid.MWAIT[.eax=40, .ebx=40, .ecx=3, .edx=1120] > (XEN) Monitor-Mwait will be used to enter C-1 state > (XEN) cpuid.MWAIT[.eax=40, .ebx=40, .ecx=3, .edx=1120] > (XEN) Monitor-Mwait will be used to enter C-3 state > (XEN) cpuid.MWAIT[.eax=40, .ebx=40, .ecx=3, .edx=1120] > (XEN) Monitor-Mwait will be used to enter C-3 state > (XEN) cpuid.MWAIT[.eax=40, .ebx=40, .ecx=3, .edx=1120] > (XEN) Monitor-Mwait will be used to enter C-1 state > (XEN) cpuid.MWAIT[.eax=40, .ebx=40, .ecx=3, .edx=1120] > (XEN) Monitor-Mwait will be used to enter C-3 state > (XEN) cpuid.MWAIT[.eax=40, .ebx=40, .ecx=3, .edx=1120] > (XEN) Monitor-Mwait will be used to enter C-3 state > (XEN) cpuid.MWAIT[.eax=40, .ebx=40, .ecx=3, .edx=1120] > (XEN) Monitor-Mwait will be used to enter C-1 state > (XEN) cpuid.MWAIT[.eax=40, .ebx=40, .ecx=3, .edx=1120] > (XEN) Monitor-Mwait will be used to enter C-3 state > (XEN) cpuid.MWAIT[.eax=40, .ebx=40, .ecx=3, .edx=1120] > (XEN) Monitor-Mwait will be used to enter C-3 state > (XEN) cpuid.MWAIT[.eax=40, .ebx=40, .ecx=3, .edx=1120] > (XEN) Monitor-Mwait will be used to enter C-1 state > (XEN) cpuid.MWAIT[.eax=40, .ebx=40, .ecx=3, .edx=1120] > (XEN) Monitor-Mwait will be used to enter C-3 state > (XEN) cpuid.MWAIT[.eax=40, .ebx=40, .ecx=3, .edx=1120] > (XEN) Monitor-Mwait will be used to enter C-3 state > (XEN) cpuid.MWAIT[.eax=40, .ebx=40, .ecx=3, .edx=1120] > (XEN) Monitor-Mwait will be used to enter C-1 state > (XEN) cpuid.MWAIT[.eax=40, .ebx=40, .ecx=3, .edx=1120] > (XEN) Monitor-Mwait will be used to enter C-3 state > (XEN) cpuid.MWAIT[.eax=40, .ebx=40, .ecx=3, .edx=1120] > (XEN) Monitor-Mwait will be used to enter C-3 state > (XEN) cpuid.MWAIT[.eax=40, .ebx=40, .ecx=3, .edx=1120] > (XEN) Monitor-Mwait will be used to enter C-1 state > (XEN) cpuid.MWAIT[.eax=40, .ebx=40, .ecx=3, .edx=1120] > (XEN) Monitor-Mwait will be used to enter C-3 state > (XEN) cpuid.MWAIT[.eax=40, .ebx=40, .ecx=3, .edx=1120] > (XEN) Monitor-Mwait will be used to enter C-3 state > (XEN) cpuid.MWAIT[.eax=40, .ebx=40, .ecx=3, .edx=1120] > (XEN) Monitor-Mwait will be used to enter C-1 state > (XEN) cpuid.MWAIT[.eax=40, .ebx=40, .ecx=3, .edx=1120] > (XEN) Monitor-Mwait will be used to enter C-3 state > (XEN) cpuid.MWAIT[.eax=40, .ebx=40, .ecx=3, .edx=1120] > (XEN) Monitor-Mwait will be used to enter C-3 state > (XEN) irq.c:1139:d0 Cannot bind IRQ 4 to guest. In use by ''ns16550''. > (XEN) irq.c:1139:d0 Cannot bind IRQ 2 to guest. In use by ''cascade''. > (XEN) irq.c:1139:d0 Cannot bind IRQ 4 to guest. In use by ''ns16550''. > (XEN) irq.c:1139:d0 Cannot bind IRQ 2 to guest. In use by ''cascade''. > (XEN) irq.c:1139:d0 Cannot bind IRQ 4 to guest. In use by ''ns16550''. > (XEN) irq.c:1139:d0 Cannot bind IRQ 2 to guest. In use by ''cascade''. > (XEN) irq.c:1139:d0 Cannot bind IRQ 4 to guest. In use by ''ns16550''. > (XEN) irq.c:1139:d0 Cannot bind IRQ 2 to guest. In use by ''cascade''. > (XEN) [VT-D]iommu.c:821: iommu_fault_status: Primary Pending Fault > (XEN) [VT-D]iommu.c:796: DMAR:[DMA Write] Request device [05:08.0] fault > addr 203a09000, iommu reg = ffff82c3fff57000 > (XEN) DMAR:[fault reason 02h] Present bit in context entry is clear > (XEN) print_vtd_entries: iommu = ffff83013fffaee0 bdf = 5:8.0 gmfn > 203a09 > (XEN) root_entry = ffff83013ff37000 > (XEN) root_entry[5] = 13cf12001 > (XEN) context = ffff83013cf12000 > (XEN) context[40] = 0_0 > (XEN) ctxt_entry[40] not present > (XEN) [VT-D]iommu.c:796: DMAR:[DMA Write] Request device [05:08.0] fault > addr 203eba000, iommu reg = ffff82c3fff57000 > (XEN) DMAR:[fault reason 02h] Present bit in context entry is clear > (XEN) print_vtd_entries: iommu = ffff83013fffaee0 bdf = 5:8.0 gmfn > 203eba > (XEN) root_entry = ffff83013ff37000 > (XEN) root_entry[5] = 13cf12001 > (XEN) context = ffff83013cf12000 > (XEN) context[40] = 0_0 > (XEN) ctxt_entry[40] not present > (XEN) [VT-D]iommu.c:821: iommu_fault_status: Primary Pending Fault > (XEN) [VT-D]iommu.c:796: DMAR:[DMA Write] Request device [05:08.0] fault > addr 204e11000, iommu reg = ffff82c3fff57000 > (XEN) DMAR:[fault reason 02h] Present bit in context entry is clear > (XEN) print_vtd_entries: iommu = ffff83013fffaee0 bdf = 5:8.0 gmfn > 204e11 > (XEN) root_entry = ffff83013ff37000 > (XEN) root_entry[5] = 13cf12001 > (XEN) context = ffff83013cf12000 > (XEN) context[40] = 0_0 > (XEN) ctxt_entry[40] not present > (XEN) [VT-D]iommu.c:821: iommu_fault_status: Primary Pending Fault > (XEN) [VT-D]iommu.c:796: DMAR:[DMA Write] Request device [05:08.0] fault > addr 2061e2000, iommu reg = ffff82c3fff57000 > (XEN) DMAR:[fault reason 02h] Present bit in context entry is clear > (XEN) print_vtd_entries: iommu = ffff83013fffaee0 bdf = 5:8.0 gmfn > 2061e2 > (XEN) root_entry = ffff83013ff37000 > (XEN) root_entry[5] = 13cf12001 > (XEN) context = ffff83013cf12000 > (XEN) context[40] = 0_0 > (XEN) ctxt_entry[40] not present > (XEN) [VT-D]iommu.c:796: DMAR:[DMA Write] Request device [05:08.0] fault > addr 205043000, iommu reg = ffff82c3fff57000 > (XEN) DMAR:[fault reason 02h] Present bit in context entry is clear > (XEN) print_vtd_entries: iommu = ffff83013fffaee0 bdf = 5:8.0 gmfn > 205043 > (XEN) root_entry = ffff83013ff37000 > (XEN) root_entry[5] = 13cf12001 > (XEN) context = ffff83013cf12000 > (XEN) context[40] = 0_0 > (XEN) ctxt_entry[40] not present > (XEN) [VT-D]iommu.c:821: iommu_fault_status: Primary Pending Fault > (XEN) [VT-D]iommu.c:796: DMAR:[DMA Write] Request device [05:08.0] fault > addr 20552b000, iommu reg = ffff82c3fff57000 > (XEN) DMAR:[fault reason 02h] Present bit in context entry is clear > (XEN) print_vtd_entries: iommu = ffff83013fffaee0 bdf = 5:8.0 gmfn > 20552b > (XEN) root_entry = ffff83013ff37000 > (XEN) root_entry[5] = 13cf12001 > (XEN) context = ffff83013cf12000 > (XEN) context[40] = 0_0 > (XEN) ctxt_entry[40] not present > (XEN) [VT-D]iommu.c:821: iommu_fault_status: Primary Pending Fault > (XEN) [VT-D]iommu.c:796: DMAR:[DMA Write] Request device [05:08.0] fault > addr 205708000, iommu reg = ffff82c3fff57000 > (XEN) DMAR:[fault reason 02h] Present bit in context entry is clear > (XEN) print_vtd_entries: iommu = ffff83013fffaee0 bdf = 5:8.0 gmfn > 205708 > (XEN) root_entry = ffff83013ff37000 > (XEN) root_entry[5] = 13cf12001 > (XEN) context = ffff83013cf12000 > (XEN) context[40] = 0_0 > (XEN) ctxt_entry[40] not present > (XEN) [VT-D]iommu.c:796: DMAR:[DMA Write] Request device [05:08.0] fault > addr 2060c0000, iommu reg = ffff82c3fff57000 > (XEN) DMAR:[fault reason 02h] Present bit in context entry is clear > (XEN) print_vtd_entries: iommu = ffff83013fffaee0 bdf = 5:8.0 gmfn > 2060c0 > (XEN) root_entry = ffff83013ff37000 > (XEN) root_entry[5] = 13cf12001 > (XEN) context = ffff83013cf12000 > (XEN) context[40] = 0_0 > (XEN) ctxt_entry[40] not present > (XEN) [VT-D]iommu.c:821: iommu_fault_status: Primary Pending Fault > (XEN) [VT-D]iommu.c:796: DMAR:[DMA Write] Request device [05:08.0] fault > addr 206591000, iommu reg = ffff82c3fff57000 > (XEN) DMAR:[fault reason 02h] Present bit in context entry is clear > (XEN) print_vtd_entries: iommu = ffff83013fffaee0 bdf = 5:8.0 gmfn > 206591 > (XEN) root_entry = ffff83013ff37000 > (XEN) root_entry[5] = 13cf12001 > (XEN) context = ffff83013cf12000 > (XEN) context[40] = 0_0 > (XEN) ctxt_entry[40] not present > (XEN) [VT-D]iommu.c:796: DMAR:[DMA Write] Request device [05:08.0] fault > addr 204353000, iommu reg = ffff82c3fff57000 > (XEN) DMAR:[fault reason 02h] Present bit in context entry is clear > (XEN) print_vtd_entries: iommu = ffff83013fffaee0 bdf = 5:8.0 gmfn > 204353 > (XEN) root_entry = ffff83013ff37000 > (XEN) root_entry[5] = 13cf12001 > (XEN) context = ffff83013cf12000 > (XEN) context[40] = 0_0 > (XEN) ctxt_entry[40] not present > (XEN) [VT-D]iommu.c:821: iommu_fault_status: Primary Pending Fault > (XEN) [VT-D]iommu.c:796: DMAR:[DMA Write] Request device [05:08.0] fault > addr 2061f2000, iommu reg = ffff82c3fff57000 > (XEN) DMAR:[fault reason 02h] Present bit in context entry is clear > (XEN) print_vtd_entries: iommu = ffff83013fffaee0 bdf = 5:8.0 gmfn > 2061f2 > (XEN) root_entry = ffff83013ff37000 > (XEN) root_entry[5] = 13cf12001 > (XEN) context = ffff83013cf12000 > (XEN) context[40] = 0_0 > (XEN) ctxt_entry[40] not present > (XEN) [VT-D]iommu.c:796: DMAR:[DMA Write] Request device [05:08.0] fault > addr 204306000, iommu reg = ffff82c3fff57000 > (XEN) DMAR:[fault reason 02h] Present bit in context entry is clear > (XEN) print_vtd_entries: iommu = ffff83013fffaee0 bdf = 5:8.0 gmfn > 204306 > (XEN) root_entry = ffff83013ff37000 > (XEN) root_entry[5] = 13cf12001 > (XEN) context = ffff83013cf12000 > (XEN) context[40] = 0_0 > (XEN) ctxt_entry[40] not present > (XEN) [VT-D]iommu.c:821: iommu_fault_status: Primary Pending Fault > (XEN) [VT-D]iommu.c:796: DMAR:[DMA Write] Request device [05:08.0] fault > addr 205f6b000, iommu reg = ffff82c3fff57000 > (XEN) DMAR:[fault reason 02h] Present bit in context entry is clear > (XEN) print_vtd_entries: iommu = ffff83013fffaee0 bdf = 5:8.0 gmfn > 205f6b > (XEN) root_entry = ffff83013ff37000 > (XEN) root_entry[5] = 13cf12001 > (XEN) context = ffff83013cf12000 > (XEN) context[40] = 0_0 > (XEN) ctxt_entry[40] not present > (XEN) [VT-D]iommu.c:796: DMAR:[DMA Write] Request device [05:08.0] fault > addr 205665000, iommu reg = ffff82c3fff57000 > (XEN) DMAR:[fault reason 02h] Present bit in context entry is clear > (XEN) print_vtd_entries: iommu = ffff83013fffaee0 bdf = 5:8.0 gmfn > 205665 > (XEN) root_entry = ffff83013ff37000 > (XEN) root_entry[5] = 13cf12001 > (XEN) context = ffff83013cf12000 > (XEN) context[40] = 0_0 > (XEN) ctxt_entry[40] not present > (XEN) [VT-D]iommu.c:821: iommu_fault_status: Primary Pending Fault > (XEN) [VT-D]iommu.c:796: DMAR:[DMA Write] Request device [05:08.0] fault > addr 2045a0000, iommu reg = ffff82c3fff57000 > (XEN) DMAR:[fault reason 02h] Present bit in context entry is clear > (XEN) print_vtd_entries: iommu = ffff83013fffaee0 bdf = 5:8.0 gmfn > 2045a0 > (XEN) root_entry = ffff83013ff37000 > (XEN) root_entry[5] = 13cf12001 > (XEN) context = ffff83013cf12000 > (XEN) context[40] = 0_0 > (XEN) ctxt_entry[40] not present > (XEN) [VT-D]iommu.c:796: DMAR:[DMA Write] Request device [05:08.0] fault > addr 205669000, iommu reg = ffff82c3fff57000 > (XEN) DMAR:[fault reason 02h] Present bit in context entry is clear > (XEN) print_vtd_entries: iommu = ffff83013fffaee0 bdf = 5:8.0 gmfn > 205669 > (XEN) root_entry = ffff83013ff37000 > (XEN) root_entry[5] = 13cf12001 > (XEN) context = ffff83013cf12000 > (XEN) context[40] = 0_0 > (XEN) ctxt_entry[40] not present > (XEN) [VT-D]iommu.c:821: iommu_fault_status: Primary Pending Fault > (XEN) [VT-D]iommu.c:796: DMAR:[DMA Write] Request device [05:08.0] fault > addr 2042c6000, iommu reg = ffff82c3fff57000 > (XEN) DMAR:[fault reason 02h] Present bit in context entry is clear > (XEN) print_vtd_entries: iommu = ffff83013fffaee0 bdf = 5:8.0 gmfn > 2042c6 > (XEN) root_entry = ffff83013ff37000 > (XEN) root_entry[5] = 13cf12001 > (XEN) context = ffff83013cf12000 > (XEN) context[40] = 0_0 > (XEN) ctxt_entry[40] not present > (XEN) [VT-D]iommu.c:796: DMAR:[DMA Write] Request device [05:08.0] fault > addr 2061fe000, iommu reg = ffff82c3fff57000 > (XEN) DMAR:[fault reason 02h] Present bit in context entry is clear > (XEN) print_vtd_entries: iommu = ffff83013fffaee0 bdf = 5:8.0 gmfn > 2061fe > (XEN) root_entry = ffff83013ff37000 > (XEN) root_entry[5] = 13cf12001 > (XEN) context = ffff83013cf12000 > (XEN) context[40] = 0_0 > (XEN) ctxt_entry[40] not present > (XEN) [VT-D]iommu.c:821: iommu_fault_status: Primary Pending Fault > (XEN) [VT-D]iommu.c:796: DMAR:[DMA Write] Request device [05:08.0] fault > addr 20560a000, iommu reg = ffff82c3fff57000 > (XEN) DMAR:[fault reason 02h] Present bit in context entry is clear > (XEN) print_vtd_entries: iommu = ffff83013fffaee0 bdf = 5:8.0 gmfn > 20560a > (XEN) root_entry = ffff83013ff37000 > (XEN) root_entry[5] = 13cf12001 > (XEN) context = ffff83013cf12000 > (XEN) context[40] = 0_0 > (XEN) ctxt_entry[40] not present > (XEN) [VT-D]iommu.c:796: DMAR:[DMA Write] Request device [05:08.0] fault > addr 206003000, iommu reg = ffff82c3fff57000 > (XEN) DMAR:[fault reason 02h] Present bit in context entry is clear > (XEN) print_vtd_entries: iommu = ffff83013fffaee0 bdf = 5:8.0 gmfn > 206003 > (XEN) root_entry = ffff83013ff37000 > (XEN) root_entry[5] = 13cf12001 > (XEN) context = ffff83013cf12000 > (XEN) context[40] = 0_0 > (XEN) ctxt_entry[40] not present > (XEN) [VT-D]iommu.c:821: iommu_fault_status: Primary Pending Fault > (XEN) [VT-D]iommu.c:796: DMAR:[DMA Write] Request device [05:08.0] fault > addr 20583e000, iommu reg = ffff82c3fff57000 > (XEN) DMAR:[fault reason 02h] Present bit in context entry is clear > (XEN) print_vtd_entries: iommu = ffff83013fffaee0 bdf = 5:8.0 gmfn > 20583e > (XEN) root_entry = ffff83013ff37000 > (XEN) root_entry[5] = 13cf12001 > (XEN) context = ffff83013cf12000 > (XEN) context[40] = 0_0 > (XEN) ctxt_entry[40] not present > (XEN) [VT-D]iommu.c:796: DMAR:[DMA Write] Request device [05:08.0] fault > addr 205615000, iommu reg = ffff82c3fff57000 > (XEN) DMAR:[fault reason 02h] Present bit in context entry is clear > (XEN) print_vtd_entries: iommu = ffff83013fffaee0 bdf = 5:8.0 gmfn > 205615 > (XEN) root_entry = ffff83013ff37000 > (XEN) root_entry[5] = 13cf12001 > (XEN) context = ffff83013cf12000 > (XEN) context[40] = 0_0 > (XEN) ctxt_entry[40] not present > (XEN) [VT-D]iommu.c:796: DMAR:[DMA Write] Request device [05:08.0] fault > addr 204265000, iommu reg = ffff82c3fff57000 > (XEN) DMAR:[fault reason 02h] Present bit in context entry is clear > (XEN) print_vtd_entries: iommu = ffff83013fffaee0 bdf = 5:8.0 gmfn > 204265 > (XEN) root_entry = ffff83013ff37000 > (XEN) root_entry[5] = 13cf12001 > (XEN) context = ffff83013cf12000 > (XEN) context[40] = 0_0 > (XEN) ctxt_entry[40] not present > (XEN) [VT-D]iommu.c:821: iommu_fault_status: Primary Pending Fault > (XEN) [VT-D]iommu.c:796: DMAR:[DMA Write] Request device [05:08.0] fault > addr 207498000, iommu reg = ffff82c3fff57000 > (XEN) DMAR:[fault reason 02h] Present bit in context entry is clear > (XEN) print_vtd_entries: iommu = ffff83013fffaee0 bdf = 5:8.0 gmfn > 207498 > (XEN) root_entry = ffff83013ff37000 > (XEN) root_entry[5] = 13cf12001 > (XEN) context = ffff83013cf12000 > (XEN) context[40] = 0_0 > (XEN) ctxt_entry[40] not present > (XEN) [VT-D]iommu.c:821: iommu_fault_status: Primary Pending Fault > (XEN) [VT-D]iommu.c:796: DMAR:[DMA Write] Request device [05:08.0] fault > addr 2049d1000, iommu reg = ffff82c3fff57000 > (XEN) DMAR:[fault reason 02h] Present bit in context entry is clear > (XEN) print_vtd_entries: iommu = ffff83013fffaee0 bdf = 5:8.0 gmfn > 2049d1 > (XEN) root_entry = ffff83013ff37000 > (XEN) root_entry[5] = 13cf12001 > (XEN) context = ffff83013cf12000 > (XEN) context[40] = 0_0 > (XEN) ctxt_entry[40] not present > (XEN) [VT-D]iommu.c:821: iommu_fault_status: Primary Pending Fault > (XEN) [VT-D]iommu.c:796: DMAR:[DMA Write] Request device [05:08.0] fault > addr 20488e000, iommu reg = ffff82c3fff57000 > (XEN) DMAR:[fault reason 02h] Present bit in context entry is clear > (XEN) print_vtd_entries: iommu = ffff83013fffaee0 bdf = 5:8.0 gmfn > 20488e > (XEN) root_entry = ffff83013ff37000 > (XEN) root_entry[5] = 13cf12001 > (XEN) context = ffff83013cf12000 > (XEN) context[40] = 0_0 > (XEN) ctxt_entry[40] not present > (XEN) [VT-D]iommu.c:821: iommu_fault_status: Primary Pending Fault > (XEN) [VT-D]iommu.c:796: DMAR:[DMA Write] Request device [05:08.0] fault > addr 205495000, iommu reg = ffff82c3fff57000 > (XEN) DMAR:[fault reason 02h] Present bit in context entry is clear > (XEN) print_vtd_entries: iommu = ffff83013fffaee0 bdf = 5:8.0 gmfn > 205495 > (XEN) root_entry = ffff83013ff37000 > (XEN) root_entry[5] = 13cf12001 > (XEN) context = ffff83013cf12000 > (XEN) context[40] = 0_0 > (XEN) ctxt_entry[40] not present > (XEN) [VT-D]iommu.c:821: iommu_fault_status: Primary Pending Fault > (XEN) [VT-D]iommu.c:796: DMAR:[DMA Write] Request device [05:08.0] fault > addr 2072d8000, iommu reg = ffff82c3fff57000 > (XEN) DMAR:[fault reason 02h] Present bit in context entry is clear > (XEN) print_vtd_entries: iommu = ffff83013fffaee0 bdf = 5:8.0 gmfn > 2072d8 > (XEN) root_entry = ffff83013ff37000 > (XEN) root_entry[5] = 13cf12001 > (XEN) context = ffff83013cf12000 > (XEN) context[40] = 0_0 > (XEN) ctxt_entry[40] not present > (XEN) [VT-D]iommu.c:821: iommu_fault_status: Primary Pending Fault > (XEN) [VT-D]iommu.c:796: DMAR:[DMA Write] Request device [05:08.0] fault > addr 2055ae000, iommu reg = ffff82c3fff57000 > (XEN) DMAR:[fault reason 02h] Present bit in context entry is clear > (XEN) print_vtd_entries: iommu = ffff83013fffaee0 bdf = 5:8.0 gmfn > 2055ae > (XEN) root_entry = ffff83013ff37000 > (XEN) root_entry[5] = 13cf12001 > (XEN) context = ffff83013cf12000 > (XEN) context[40] = 0_0 > (XEN) ctxt_entry[40] not present > (XEN) [VT-D]iommu.c:821: iommu_fault_status: Primary Pending Fault > (XEN) [VT-D]iommu.c:796: DMAR:[DMA Write] Request device [05:08.0] fault > addr 205544000, iommu reg = ffff82c3fff57000 > (XEN) DMAR:[fault reason 02h] Present bit in context entry is clear > (XEN) print_vtd_entries: iommu = ffff83013fffaee0 bdf = 5:8.0 gmfn > 205544 > (XEN) root_entry = ffff83013ff37000 > (XEN) root_entry[5] = 13cf12001 > (XEN) context = ffff83013cf12000 > (XEN) context[40] = 0_0 > (XEN) ctxt_entry[40] not present > (XEN) [VT-D]iommu.c:796: DMAR:[DMA Write] Request device [05:08.0] fault > addr 204865000, iommu reg = ffff82c3fff57000 > (XEN) DMAR:[fault reason 02h] Present bit in context entry is clear > (XEN) print_vtd_entries: iommu = ffff83013fffaee0 bdf = 5:8.0 gmfn > 204865 > (XEN) root_entry = ffff83013ff37000 > (XEN) root_entry[5] = 13cf12001 > (XEN) context = ffff83013cf12000 > (XEN) context[40] = 0_0 > (XEN) ctxt_entry[40] not present > (XEN) [VT-D]iommu.c:821: iommu_fault_status: Primary Pending Fault > (XEN) [VT-D]iommu.c:796: DMAR:[DMA Write] Request device [05:08.0] fault > addr 2074be000, iommu reg = ffff82c3fff57000 > (XEN) DMAR:[fault reason 02h] Present bit in context entry is clear > (XEN) print_vtd_entries: iommu = ffff83013fffaee0 bdf = 5:8.0 gmfn > 2074be > (XEN) root_entry = ffff83013ff37000 > (XEN) root_entry[5] = 13cf12001 > (XEN) context = ffff83013cf12000 > (XEN) context[40] = 0_0 > (XEN) ctxt_entry[40] not present > > (XEN) [VT-D]iommu.c:796: DMAR:[DMA Write] Request device [05:08.0] fault > addr 204865000, iommu reg = ffff82c3fff57000 > (XEN) DMAR:[fault reason 02h] Present bit in context entry is clear > (XEN) print_vtd_entries: iommu = ffff83013fffaee0 bdf = 5:8.0 gmfn > 204865 > (XEN) root_entry = ffff83013ff37000 > (XEN) root_entry[5] = 13cf12001 > (XEN) context = ffff83013cf12000 > (XEN) context[40] = 0_0 > (XEN) ctxt_entry[40] not present > (XEN) [VT-D]iommu.c:821: iommu_fault_status: Primary Pending Fault > (XEN) [VT-D]iommu.c:796: DMAR:[DMA Write] Request device [05:08.0] fault > addr 2074be000, iommu reg = ffff82c3fff57000 > (XEN) DMAR:[fault reason 02h] Present bit in context entry is clear > (XEN) print_vtd_entries: iommu = ffff83013fffaee0 bdf = 5:8.0 gmfn > 2074be > (XEN) root_entry = ffff83013ff37000 > (XEN) root_entry[5] = 13cf12001 > (XEN) context = ffff83013cf12000 > (XEN) context[40] = 0_0 > (XEN) ctxt_entry[40] not present > > (XEN) [VT-D]iommu.c:796: DMAR:[DMA Write] Request device [05:08.0] fault > addr 204865000, iommu reg = ffff82c3fff57000 > (XEN) DMAR:[fault reason 02h] Present bit in context entry is clear > (XEN) print_vtd_entries: iommu = ffff83013fffaee0 bdf = 5:8.0 gmfn > 204865 > (XEN) root_entry = ffff83013ff37000 > (XEN) root_entry[5] = 13cf12001 > (XEN) context = ffff83013cf12000 > (XEN) context[40] = 0_0 > (XEN) ctxt_entry[40] not present > (XEN) [VT-D]iommu.c:821: iommu_fault_status: Primary Pending Fault > (XEN) [VT-D]iommu.c:796: DMAR:[DMA Write] Request device [05:08.0] fault > addr 2074be000, iommu reg = ffff82c3fff57000 > (XEN) DMAR:[fault reason 02h] Present bit in context entry is clear > (XEN) print_vtd_entries: iommu = ffff83013fffaee0 bdf = 5:8.0 gmfn > 2074be > (XEN) root_entry = ffff83013ff37000 > (XEN) root_entry[5] = 13cf12001 > (XEN) context = ffff83013cf12000 > (XEN) context[40] = 0_0 > (XEN) ctxt_entry[40] not present > > (XEN) [VT-D]iommu.c:796: DMAR:[DMA Write] Request device [05:08.0] fault > addr 204865000, iommu reg = ffff82c3fff57000 > (XEN) DMAR:[fault reason 02h] Present bit in context entry is clear > (XEN) print_vtd_entries: iommu = ffff83013fffaee0 bdf = 5:8.0 gmfn > 204865 > (XEN) root_entry = ffff83013ff37000 > (XEN) root_entry[5] = 13cf12001 > (XEN) context = ffff83013cf12000 > (XEN) context[40] = 0_0 > (XEN) ctxt_entry[40] not present > (XEN) [VT-D]iommu.c:821: iommu_fault_status: Primary Pending Fault > (XEN) [VT-D]iommu.c:796: DMAR:[DMA Write] Request device [05:08.0] fault > addr 2074be000, iommu reg = ffff82c3fff57000 > (XEN) DMAR:[fault reason 02h] Present bit in context entry is clear > (XEN) print_vtd_entries: iommu = ffff83013fffaee0 bdf = 5:8.0 gmfn > 2074be > (XEN) root_entry = ffff83013ff37000 > (XEN) root_entry[5] = 13cf12001 > (XEN) context = ffff83013cf12000 > (XEN) context[40] = 0_0 > (XEN) ctxt_entry[40] not present > > (XEN) [VT-D]iommu.c:796: DMAR:[DMA Write] Request device [05:08.0] fault > addr 204865000, iommu reg = ffff82c3fff57000 > (XEN) DMAR:[fault reason 02h] Present bit in context entry is clear > (XEN) print_vtd_entries: iommu = ffff83013fffaee0 bdf = 5:8.0 gmfn > 204865 > (XEN) root_entry = ffff83013ff37000 > (XEN) root_entry[5] = 13cf12001 > (XEN) context = ffff83013cf12000 > (XEN) context[40] = 0_0 > (XEN) ctxt_entry[40] not present > (XEN) [VT-D]iommu.c:821: iommu_fault_status: Primary Pending Fault > (XEN) [VT-D]iommu.c:796: DMAR:[DMA Write] Request device [05:08.0] fault > addr 2074be000, iommu reg = ffff82c3fff57000 > (XEN) DMAR:[fault reason 02h] Present bit in context entry is clear > (XEN) print_vtd_entries: iommu = ffff83013fffaee0 bdf = 5:8.0 gmfn > 2074be > (XEN) root_entry = ffff83013ff37000 > (XEN) root_entry[5] = 13cf12001 > (XEN) context = ffff83013cf12000 > (XEN) context[40] = 0_0 > (XEN) ctxt_entry[40] not present > > (XEN) [VT-D]iommu.c:796: DMAR:[DMA Write] Request device [05:08.0] fault > addr 204865000, iommu reg = ffff82c3fff57000 > (XEN) DMAR:[fault reason 02h] Present bit in context entry is clear > (XEN) print_vtd_entries: iommu = ffff83013fffaee0 bdf = 5:8.0 gmfn > 204865 > (XEN) root_entry = ffff83013ff37000 > (XEN) root_entry[5] = 13cf12001 > (XEN) context = ffff83013cf12000 > (XEN) context[40] = 0_0 > (XEN) ctxt_entry[40] not present > (XEN) [VT-D]iommu.c:821: iommu_fault_status: Primary Pending Fault > (XEN) [VT-D]iommu.c:796: DMAR:[DMA Write] Request device [05:08.0] fault > addr 2074be000, iommu reg = ffff82c3fff57000 > (XEN) DMAR:[fault reason 02h] Present bit in context entry is clear > (XEN) print_vtd_entries: iommu = ffff83013fffaee0 bdf = 5:8.0 gmfn > 2074be > (XEN) root_entry = ffff83013ff37000 > (XEN) root_entry[5] = 13cf12001 > (XEN) context = ffff83013cf12000 > (XEN) context[40] = 0_0 > (XEN) ctxt_entry[40] not present > > (XEN) [VT-D]iommu.c:796: DMAR:[DMA Write] Request device [05:08.0] fault > addr 204865000, iommu reg = ffff82c3fff57000 > (XEN) DMAR:[fault reason 02h] Present bit in context entry is clear > (XEN) print_vtd_entries: iommu = ffff83013fffaee0 bdf = 5:8.0 gmfn > 204865 > (XEN) root_entry = ffff83013ff37000 > (XEN) root_entry[5] = 13cf12001 > (XEN) context = ffff83013cf12000 > (XEN) context[40] = 0_0 > (XEN) ctxt_entry[40] not present > (XEN) [VT-D]iommu.c:821: iommu_fault_status: Primary Pending Fault > (XEN) [VT-D]iommu.c:796: DMAR:[DMA Write] Request device [05:08.0] fault > addr 2074be000, iommu reg = ffff82c3fff57000 > (XEN) DMAR:[fault reason 02h] Present bit in context entry is clear > (XEN) print_vtd_entries: iommu = ffff83013fffaee0 bdf = 5:8.0 gmfn > 2074be > (XEN) root_entry = ffff83013ff37000 > (XEN) root_entry[5] = 13cf12001 > (XEN) context = ffff83013cf12000 > (XEN) context[40] = 0_0 > (XEN) ctxt_entry[40] not present > > (XEN) context[40] = 0_0 > (XEN) ctxt_entry[40] not present > (XEN) [VT-D]iommu.c:796: DMAR:[DMA Write] Request device [05:08.0] fault > addr 204865000, iommu reg = ffff82c3fff57000 > (XEN) DMAR:[fault reason 02h] Present bit in context entry is clear > (XEN) print_vtd_entries: iommu = ffff83013fffaee0 bdf = 5:8.0 gmfn > 204865 > (XEN) root_entry = ffff83013ff37000 > (XEN) root_entry[5] = 13cf12001 > (XEN) context = ffff83013cf12000 > (XEN) context[40] = 0_0 > (XEN) ctxt_entry[40] not present > (XEN) [VT-D]iommu.c:821: iommu_fault_status: Primary Pending Fault > (XEN) [VT-D]iommu.c:796: DMAR:[DMA Write] Request device [05:08.0] fault > addr 2074be000, iommu reg = ffff82c3fff57000 > (XEN) DMAR:[fault reason 02h] Present bit in context entry is clear > (XEN) print_vtd_entries: iommu = ffff83013fffaee0 bdf = 5:8.0 gmfn > 2074be > (XEN) root_entry = ffff83013ff37000 > (XEN) root_entry[5] = 13cf12001 > (XEN) context = ffff83013cf12000 > (XEN) context[40] = 0_0 > (XEN) ctxt_entry[40] not present > > (XEN) context[40] = 0_0 > (XEN) ctxt_entry[40] not present > (XEN) [VT-D]iommu.c:796: DMAR:[DMA Write] Request device [05:08.0] fault > addr 204865000, iommu reg = ffff82c3fff57000 > (XEN) DMAR:[fault reason 02h] Present bit in context entry is clear > (XEN) print_vtd_entries: iommu = ffff83013fffaee0 bdf = 5:8.0 gmfn > 204865 > (XEN) root_entry = ffff83013ff37000 > (XEN) root_entry[5] = 13cf12001 > (XEN) context = ffff83013cf12000 > (XEN) context[40] = 0_0 > (XEN) ctxt_entry[40] not present > (XEN) [VT-D]iommu.c:821: iommu_fault_status: Primary Pending Fault > (XEN) [VT-D]iommu.c:796: DMAR:[DMA Write] Request device [05:08.0] fault > addr 2074be000, iommu reg = ffff82c3fff57000 > (XEN) DMAR:[fault reason 02h] Present bit in context entry is clear > (XEN) print_vtd_entries: iommu = ffff83013fffaee0 bdf = 5:8.0 gmfn > 2074be > (XEN) root_entry = ffff83013ff37000 > (XEN) root_entry[5] = 13cf12001 > (XEN) context = ffff83013cf12000 > (XEN) context[40] = 0_0 > (XEN) ctxt_entry[40] not present > > (XEN) context[40] = 0_0 > (XEN) ctxt_entry[40] not present > (XEN) [VT-D]iommu.c:796: DMAR:[DMA Write] Request device [05:08.0] fault > addr 204865000, iommu reg = ffff82c3fff57000 > (XEN) DMAR:[fault reason 02h] Present bit in context entry is clear > (XEN) print_vtd_entries: iommu = ffff83013fffaee0 bdf = 5:8.0 gmfn > 204865 > (XEN) root_entry = ffff83013ff37000 > (XEN) root_entry[5] = 13cf12001 > (XEN) context = ffff83013cf12000 > (XEN) context[40] = 0_0 > (XEN) ctxt_entry[40] not present > (XEN) [VT-D]iommu.c:821: iommu_fault_status: Primary Pending Fault > (XEN) [VT-D]iommu.c:796: DMAR:[DMA Write] Request device [05:08.0] fault > addr 2074be000, iommu reg = ffff82c3fff57000 > (XEN) DMAR:[fault reason 02h] Present bit in context entry is clear > (XEN) print_vtd_entries: iommu = ffff83013fffaee0 bdf = 5:8.0 gmfn > 2074be > (XEN) root_entry = ffff83013ff37000 > (XEN) root_entry[5] = 13cf12001 > (XEN) context = ffff83013cf12000 > (XEN) context[40] = 0_0 > (XEN) ctxt_entry[40] not present > > (XEN) context[40] = 0_0 > (XEN) ctxt_entry[40] not present > (XEN) [VT-D]iommu.c:796: DMAR:[DMA Write] Request device [05:08.0] fault > addr 204865000, iommu reg = ffff82c3fff57000 > (XEN) DMAR:[fault reason 02h] Present bit in context entry is clear > (XEN) print_vtd_entries: iommu = ffff83013fffaee0 bdf = 5:8.0 gmfn > 204865 > (XEN) root_entry = ffff83013ff37000 > (XEN) root_entry[5] = 13cf12001 > (XEN) context = ffff83013cf12000 > (XEN) context[40] = 0_0 > (XEN) ctxt_entry[40] not present > (XEN) [VT-D]iommu.c:821: iommu_fault_status: Primary Pending Fault > (XEN) [VT-D]iommu.c:796: DMAR:[DMA Write] Request device [05:08.0] fault > addr 2074be000, iommu reg = ffff82c3fff57000 > (XEN) DMAR:[fault reason 02h] Present bit in context entry is clear > (XEN) print_vtd_entries: iommu = ffff83013fffaee0 bdf = 5:8.0 gmfn > 2074be > (XEN) root_entry = ffff83013ff37000 > (XEN) root_entry[5] = 13cf12001 > (XEN) context = ffff83013cf12000 > (XEN) context[40] = 0_0 > (XEN) ctxt_entry[40] not present > > > _______________________________________________ > Xen-devel mailing list > Xen-devel@lists.xensource.com > http://lists.xensource.com/xen-devel >_______________________________________________ Xen-devel mailing list Xen-devel@lists.xensource.com http://lists.xensource.com/xen-devel
M. Nunberg
2010-Jun-02 01:40 UTC
Re: [Xen-devel] iommuu/vt-d issues with LSI MegaSAS (PERC5i)
The card is PCIe, not PCI-X; I might note that this card is an x8 card in an x4 slot.. I do not think this is an issue, but maybe... Booting with limiting the memory uunder 4GB, bare metal + DMAR, swiotlb etc. all fail.. I can send the log in another post (whiich I will do shortly) Here is the full lspci -vvv output: 00:00.0 Host bridge: Intel Corporation 5500 I/O Hub to ESI Port (rev 13) Subsystem: Super Micro Computer Inc Device 000b Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Capabilities: [60] Message Signalled Interrupts: Mask+ 64bit- Queue=0/1 Enable- Address: 00000000 Data: 0000 Masking: 00000000 Pending: 00000000 Capabilities: [90] Express (v2) Root Port (Slot-), MSI 00 DevCap: MaxPayload 128 bytes, PhantFunc 0, Latency L0s <64ns, L1 <1us ExtTag+ RBE+ FLReset- DevCtl: Report errors: Correctable- Non-Fatal- Fatal- Unsupported- RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop- MaxPayload 128 bytes, MaxReadReq 128 bytes DevSta: CorrErr- UncorrErr- FatalErr- UnsuppReq- AuxPwr- TransPend- LnkCap: Port #0, Speed 2.5GT/s, Width x4, ASPM L0s L1, Latency L0 <512ns, L1 <64us ClockPM- Suprise+ LLActRep+ BwNot+ LnkCtl: ASPM Disabled; RCB 64 bytes Disabled- Retrain- CommClk- ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt- LnkSta: Speed 2.5GT/s, Width x4, TrErr- Train- SlotClk+ DLActive+ BWMgmt- ABWMgmt- RootCtl: ErrCorrectable- ErrNon-Fatal- ErrFatal- PMEIntEna- CRSVisible- RootCap: CRSVisible- RootSta: PME ReqID 0000, PMEStatus- PMEPending- Capabilities: [e0] Power Management version 3 Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0+,D1-,D2-,D3hot +,D3cold+) Status: D0 PME-Enable- DSel=0 DScale=0 PME- Capabilities: [100] Advanced Error Reporting <?> Capabilities: [150] Access Controls <?> Capabilities: [160] Vendor Specific Information <?> 00:01.0 PCI bridge: Intel Corporation 5520/5500/X58 I/O Hub PCI Express Root Port 1 (rev 13) (prog-if 00 [Normal decode]) Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx+ Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0, Cache Line Size: 64 bytes Bus: primary=00, secondary=01, subordinate=01, sec-latency=0 I/O behind bridge: 0000b000-0000bfff Memory behind bridge: f3f00000-f6ffffff Prefetchable memory behind bridge: 00000000c0000000-00000000cfffffff Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort+ <SERR- <PERR- BridgeCtl: Parity- SERR+ NoISA- VGA- MAbort- >Reset- FastB2B- PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn- Capabilities: [40] Subsystem: Super Micro Computer Inc Device 000b Capabilities: [60] Message Signalled Interrupts: Mask+ 64bit- Queue=0/1 Enable+ Address: fee00000 Data: 40b0 Masking: 00000003 Pending: 00000000 Capabilities: [90] Express (v2) Root Port (Slot+), MSI 00 DevCap: MaxPayload 256 bytes, PhantFunc 0, Latency L0s <64ns, L1 <1us ExtTag+ RBE+ FLReset- DevCtl: Report errors: Correctable+ Non-Fatal+ Fatal+ Unsupported- RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop- MaxPayload 128 bytes, MaxReadReq 128 bytes DevSta: CorrErr+ UncorrErr- FatalErr- UnsuppReq- AuxPwr- TransPend- LnkCap: Port #0, Speed 5GT/s, Width x4, ASPM L0s L1, Latency L0 <512ns, L1 <64us ClockPM- Suprise+ LLActRep+ BwNot+ LnkCtl: ASPM L0s Enabled; RCB 64 bytes Disabled- Retrain- CommClk+ ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt- LnkSta: Speed 2.5GT/s, Width x4, TrErr- Train- SlotClk+ DLActive+ BWMgmt+ ABWMgmt- SltCap: AttnBtn- PwrCtrl- MRL- AttnInd- PwrInd- HotPlug- Surpise- Slot # 2, PowerLimit 25.000000; Interlock- NoCompl- SltCtl: Enable: AttnBtn- PwrFlt- MRL- PresDet- CmdCplt- HPIrq- LinkChg- Control: AttnInd Off, PwrInd Off, Power- Interlock- SltSta: Status: AttnBtn- PowerFlt- MRL- CmdCplt- PresDet+ Interlock- Changed: MRL- PresDet+ LinkState+ RootCtl: ErrCorrectable+ ErrNon-Fatal+ ErrFatal+ PMEIntEna- CRSVisible- RootCap: CRSVisible- RootSta: PME ReqID 0000, PMEStatus- PMEPending- Capabilities: [e0] Power Management version 3 Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0+,D1-,D2-,D3hot +,D3cold+) Status: D0 PME-Enable- DSel=0 DScale=0 PME- Capabilities: [100] Advanced Error Reporting <?> Capabilities: [150] Access Controls <?> Capabilities: [160] Vendor Specific Information <?> Kernel driver in use: pcieport-driver Kernel modules: shpchp 00:03.0 PCI bridge: Intel Corporation 5520/5500/X58 I/O Hub PCI Express Root Port 3 (rev 13) (prog-if 00 [Normal decode]) Control: I/O- Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx+ Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0, Cache Line Size: 64 bytes Bus: primary=00, secondary=02, subordinate=02, sec-latency=0 I/O behind bridge: 0000f000-00000fff Memory behind bridge: fff00000-000fffff Prefetchable memory behind bridge: 00000000fff00000-00000000000fffff Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- <SERR- <PERR- BridgeCtl: Parity- SERR+ NoISA- VGA- MAbort- >Reset- FastB2B- PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn- Capabilities: [40] Subsystem: Super Micro Computer Inc Device 000b Capabilities: [60] Message Signalled Interrupts: Mask+ 64bit- Queue=0/1 Enable+ Address: fee00000 Data: 40b8 Masking: 00000003 Pending: 00000000 Capabilities: [90] Express (v2) Root Port (Slot+), MSI 00 DevCap: MaxPayload 256 bytes, PhantFunc 0, Latency L0s <64ns, L1 <1us ExtTag+ RBE+ FLReset- DevCtl: Report errors: Correctable+ Non-Fatal+ Fatal+ Unsupported- RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop- MaxPayload 128 bytes, MaxReadReq 128 bytes DevSta: CorrErr- UncorrErr- FatalErr- UnsuppReq- AuxPwr- TransPend- LnkCap: Port #0, Speed 5GT/s, Width x4, ASPM L0s L1, Latency L0 <512ns, L1 <64us ClockPM- Suprise+ LLActRep+ BwNot+ LnkCtl: ASPM Disabled; RCB 64 bytes Disabled- Retrain- CommClk+ ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt- LnkSta: Speed 2.5GT/s, Width x0, TrErr- Train- SlotClk+ DLActive- BWMgmt- ABWMgmt- SltCap: AttnBtn- PwrCtrl- MRL- AttnInd- PwrInd- HotPlug- Surpise- Slot # 33, PowerLimit 25.000000; Interlock- NoCompl- SltCtl: Enable: AttnBtn- PwrFlt- MRL- PresDet- CmdCplt- HPIrq- LinkChg- Control: AttnInd Off, PwrInd Off, Power- Interlock- SltSta: Status: AttnBtn- PowerFlt- MRL- CmdCplt- PresDet- Interlock- Changed: MRL- PresDet+ LinkState- RootCtl: ErrCorrectable+ ErrNon-Fatal+ ErrFatal+ PMEIntEna- CRSVisible- RootCap: CRSVisible- RootSta: PME ReqID 0000, PMEStatus- PMEPending- Capabilities: [e0] Power Management version 3 Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0+,D1-,D2-,D3hot +,D3cold+) Status: D0 PME-Enable- DSel=0 DScale=0 PME- Capabilities: [100] Advanced Error Reporting <?> Capabilities: [150] Access Controls <?> Capabilities: [160] Vendor Specific Information <?> Kernel driver in use: pcieport-driver Kernel modules: shpchp 00:07.0 PCI bridge: Intel Corporation 5520/5500/X58 I/O Hub PCI Express Root Port 7 (rev 13) (prog-if 00 [Normal decode]) Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx+ Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0, Cache Line Size: 64 bytes Bus: primary=00, secondary=03, subordinate=03, sec-latency=0 I/O behind bridge: 0000c000-0000cfff Memory behind bridge: f7f00000-faffffff Prefetchable memory behind bridge: 00000000d0000000-00000000dfffffff Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- <SERR- <PERR- BridgeCtl: Parity- SERR+ NoISA- VGA+ MAbort- >Reset- FastB2B- PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn- Capabilities: [40] Subsystem: Super Micro Computer Inc Device 000b Capabilities: [60] Message Signalled Interrupts: Mask+ 64bit- Queue=0/1 Enable+ Address: fee00000 Data: 40c0 Masking: 00000003 Pending: 00000000 Capabilities: [90] Express (v2) Root Port (Slot+), MSI 00 DevCap: MaxPayload 256 bytes, PhantFunc 0, Latency L0s <64ns, L1 <1us ExtTag+ RBE+ FLReset- DevCtl: Report errors: Correctable+ Non-Fatal+ Fatal+ Unsupported- RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop- MaxPayload 128 bytes, MaxReadReq 128 bytes DevSta: CorrErr- UncorrErr- FatalErr- UnsuppReq- AuxPwr- TransPend- LnkCap: Port #0, Speed 5GT/s, Width x16, ASPM L0s L1, Latency L0 <512ns, L1 <64us ClockPM- Suprise+ LLActRep+ BwNot+ LnkCtl: ASPM L0s Enabled; RCB 64 bytes Disabled- Retrain- CommClk+ ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt- LnkSta: Speed 5GT/s, Width x16, TrErr- Train- SlotClk+ DLActive+ BWMgmt+ ABWMgmt- SltCap: AttnBtn- PwrCtrl- MRL- AttnInd- PwrInd- HotPlug- Surpise- Slot # 5, PowerLimit 75.000000; Interlock- NoCompl- SltCtl: Enable: AttnBtn- PwrFlt- MRL- PresDet- CmdCplt- HPIrq- LinkChg- Control: AttnInd Off, PwrInd Off, Power- Interlock- SltSta: Status: AttnBtn- PowerFlt- MRL- CmdCplt- PresDet+ Interlock- Changed: MRL- PresDet+ LinkState+ RootCtl: ErrCorrectable+ ErrNon-Fatal+ ErrFatal+ PMEIntEna- CRSVisible- RootCap: CRSVisible- RootSta: PME ReqID 0000, PMEStatus- PMEPending- Capabilities: [e0] Power Management version 3 Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0+,D1-,D2-,D3hot +,D3cold+) Status: D0 PME-Enable- DSel=0 DScale=0 PME- Capabilities: [100] Advanced Error Reporting <?> Capabilities: [150] Access Controls <?> Capabilities: [160] Vendor Specific Information <?> Kernel driver in use: pcieport-driver Kernel modules: shpchp 00:14.0 PIC: Intel Corporation 5520/5500/X58 I/O Hub System Management Registers (rev 13) (prog-if 00 [8259]) Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Capabilities: [40] Express (v2) Root Complex Integrated Endpoint, MSI 00 DevCap: MaxPayload 128 bytes, PhantFunc 0, Latency L0s <64ns, L1 <1us ExtTag- RBE+ FLReset- DevCtl: Report errors: Correctable- Non-Fatal- Fatal- Unsupported- RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop- MaxPayload 128 bytes, MaxReadReq 128 bytes DevSta: CorrErr- UncorrErr- FatalErr- UnsuppReq- AuxPwr- TransPend- LnkCap: Port #0, Speed unknown, Width x0, ASPM L0s, Latency L0 unlimited, L1 unlimited ClockPM- Suprise+ LLActRep+ BwNot+ LnkCtl: ASPM Disabled; Disabled- Retrain- CommClk- ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt- LnkSta: Speed unknown, Width x0, TrErr- Train- SlotClk+ DLActive- BWMgmt- ABWMgmt- 00:14.1 PIC: Intel Corporation 5520/5500/X58 I/O Hub GPIO and Scratch Pad Registers (rev 13) (prog-if 00 [8259]) Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Capabilities: [40] Express (v2) Root Complex Integrated Endpoint, MSI 00 DevCap: MaxPayload 128 bytes, PhantFunc 0, Latency L0s <64ns, L1 <1us ExtTag- RBE+ FLReset- DevCtl: Report errors: Correctable- Non-Fatal- Fatal- Unsupported- RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop- MaxPayload 128 bytes, MaxReadReq 128 bytes DevSta: CorrErr- UncorrErr- FatalErr- UnsuppReq- AuxPwr- TransPend- LnkCap: Port #0, Speed unknown, Width x0, ASPM L0s, Latency L0 unlimited, L1 unlimited ClockPM- Suprise+ LLActRep+ BwNot+ LnkCtl: ASPM Disabled; Disabled- Retrain- CommClk- ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt- LnkSta: Speed unknown, Width x0, TrErr- Train- SlotClk+ DLActive- BWMgmt- ABWMgmt- 00:14.2 PIC: Intel Corporation 5520/5500/X58 I/O Hub Control Status and RAS Registers (rev 13) (prog-if 00 [8259]) Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Capabilities: [40] Express (v2) Root Complex Integrated Endpoint, MSI 00 DevCap: MaxPayload 128 bytes, PhantFunc 0, Latency L0s <64ns, L1 <1us ExtTag- RBE+ FLReset- DevCtl: Report errors: Correctable- Non-Fatal- Fatal- Unsupported- RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop- MaxPayload 128 bytes, MaxReadReq 128 bytes DevSta: CorrErr- UncorrErr- FatalErr- UnsuppReq- AuxPwr- TransPend- LnkCap: Port #0, Speed unknown, Width x0, ASPM L0s, Latency L0 unlimited, L1 unlimited ClockPM- Suprise+ LLActRep+ BwNot+ LnkCtl: ASPM Disabled; Disabled- Retrain- CommClk- ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt- LnkSta: Speed unknown, Width x0, TrErr- Train- SlotClk+ DLActive- BWMgmt- ABWMgmt- 00:14.3 PIC: Intel Corporation 5520/5500/X58 I/O Hub Throttle Registers (rev 13) (prog-if 00 [8259]) Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- 00:16.0 System peripheral: Intel Corporation 5520/5500/X58 Chipset QuickData Technology Device (rev 13) Subsystem: Super Micro Computer Inc Device 000b Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0, Cache Line Size: 64 bytes Interrupt: pin A routed to IRQ 11 Region 0: Memory at fbbfc000 (64-bit, non-prefetchable) [size=16K] Capabilities: [80] MSI-X: Enable- Mask- TabSize=1 Vector table: BAR=0 offset=00002000 PBA: BAR=0 offset=00003000 Capabilities: [90] Express (v2) Root Complex Integrated Endpoint, MSI 00 DevCap: MaxPayload 128 bytes, PhantFunc 0, Latency L0s <64ns, L1 <1us ExtTag- RBE+ FLReset- DevCtl: Report errors: Correctable- Non-Fatal- Fatal- Unsupported- RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop- MaxPayload 128 bytes, MaxReadReq 128 bytes DevSta: CorrErr- UncorrErr- FatalErr- UnsuppReq- AuxPwr- TransPend- LnkCap: Port #0, Speed unknown, Width x0, ASPM unknown, Latency L0 <64ns, L1 <1us ClockPM- Suprise- LLActRep- BwNot- LnkCtl: ASPM Disabled; Disabled- Retrain- CommClk- ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt- LnkSta: Speed unknown, Width x0, TrErr- Train- SlotClk- DLActive- BWMgmt- ABWMgmt- Capabilities: [e0] Power Management version 3 Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-) Status: D0 PME-Enable- DSel=0 DScale=0 PME- 00:16.1 System peripheral: Intel Corporation 5520/5500/X58 Chipset QuickData Technology Device (rev 13) Subsystem: Super Micro Computer Inc Device 000b Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0, Cache Line Size: 64 bytes Interrupt: pin B routed to IRQ 10 Region 0: Memory at fbbf8000 (64-bit, non-prefetchable) [size=16K] Capabilities: [80] MSI-X: Enable- Mask- TabSize=1 Vector table: BAR=0 offset=00002000 PBA: BAR=0 offset=00003000 Capabilities: [90] Express (v2) Root Complex Integrated Endpoint, MSI 00 DevCap: MaxPayload 128 bytes, PhantFunc 0, Latency L0s <64ns, L1 <1us ExtTag- RBE+ FLReset- DevCtl: Report errors: Correctable- Non-Fatal- Fatal- Unsupported- RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop- MaxPayload 128 bytes, MaxReadReq 128 bytes DevSta: CorrErr- UncorrErr- FatalErr- UnsuppReq- AuxPwr- TransPend- LnkCap: Port #0, Speed unknown, Width x0, ASPM unknown, Latency L0 <64ns, L1 <1us ClockPM- Suprise- LLActRep- BwNot- LnkCtl: ASPM Disabled; Disabled- Retrain- CommClk- ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt- LnkSta: Speed unknown, Width x0, TrErr- Train- SlotClk- DLActive- BWMgmt- ABWMgmt- Capabilities: [e0] Power Management version 3 Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-) Status: D0 PME-Enable- DSel=0 DScale=0 PME- 00:16.2 System peripheral: Intel Corporation 5520/5500/X58 Chipset QuickData Technology Device (rev 13) Subsystem: Super Micro Computer Inc Device 000b Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0, Cache Line Size: 64 bytes Interrupt: pin C routed to IRQ 14 Region 0: Memory at fbbf4000 (64-bit, non-prefetchable) [size=16K] Capabilities: [80] MSI-X: Enable- Mask- TabSize=1 Vector table: BAR=0 offset=00002000 PBA: BAR=0 offset=00003000 Capabilities: [90] Express (v2) Root Complex Integrated Endpoint, MSI 00 DevCap: MaxPayload 128 bytes, PhantFunc 0, Latency L0s <64ns, L1 <1us ExtTag- RBE+ FLReset- DevCtl: Report errors: Correctable- Non-Fatal- Fatal- Unsupported- RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop- MaxPayload 128 bytes, MaxReadReq 128 bytes DevSta: CorrErr- UncorrErr- FatalErr- UnsuppReq- AuxPwr- TransPend- LnkCap: Port #0, Speed unknown, Width x0, ASPM unknown, Latency L0 <64ns, L1 <1us ClockPM- Suprise- LLActRep- BwNot- LnkCtl: ASPM Disabled; Disabled- Retrain- CommClk- ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt- LnkSta: Speed unknown, Width x0, TrErr- Train- SlotClk- DLActive- BWMgmt- ABWMgmt- Capabilities: [e0] Power Management version 3 Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-) Status: D0 PME-Enable- DSel=0 DScale=0 PME- 00:16.3 System peripheral: Intel Corporation 5520/5500/X58 Chipset QuickData Technology Device (rev 13) Subsystem: Super Micro Computer Inc Device 000b Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0, Cache Line Size: 64 bytes Interrupt: pin D routed to IRQ 15 Region 0: Memory at fbbf0000 (64-bit, non-prefetchable) [size=16K] Capabilities: [80] MSI-X: Enable- Mask- TabSize=1 Vector table: BAR=0 offset=00002000 PBA: BAR=0 offset=00003000 Capabilities: [90] Express (v2) Root Complex Integrated Endpoint, MSI 00 DevCap: MaxPayload 128 bytes, PhantFunc 0, Latency L0s <64ns, L1 <1us ExtTag- RBE+ FLReset- DevCtl: Report errors: Correctable- Non-Fatal- Fatal- Unsupported- RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop- MaxPayload 128 bytes, MaxReadReq 128 bytes DevSta: CorrErr- UncorrErr- FatalErr- UnsuppReq- AuxPwr- TransPend- LnkCap: Port #0, Speed unknown, Width x0, ASPM unknown, Latency L0 <64ns, L1 <1us ClockPM- Suprise- LLActRep- BwNot- LnkCtl: ASPM Disabled; Disabled- Retrain- CommClk- ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt- LnkSta: Speed unknown, Width x0, TrErr- Train- SlotClk- DLActive- BWMgmt- ABWMgmt- Capabilities: [e0] Power Management version 3 Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-) Status: D0 PME-Enable- DSel=0 DScale=0 PME- 00:16.4 System peripheral: Intel Corporation 5520/5500/X58 Chipset QuickData Technology Device (rev 13) Subsystem: Super Micro Computer Inc Device 000b Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0, Cache Line Size: 64 bytes Interrupt: pin A routed to IRQ 11 Region 0: Memory at fbbec000 (64-bit, non-prefetchable) [size=16K] Capabilities: [80] MSI-X: Enable- Mask- TabSize=1 Vector table: BAR=0 offset=00002000 PBA: BAR=0 offset=00003000 Capabilities: [90] Express (v2) Root Complex Integrated Endpoint, MSI 00 DevCap: MaxPayload 128 bytes, PhantFunc 0, Latency L0s <64ns, L1 <1us ExtTag- RBE+ FLReset- DevCtl: Report errors: Correctable- Non-Fatal- Fatal- Unsupported- RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop- MaxPayload 128 bytes, MaxReadReq 128 bytes DevSta: CorrErr- UncorrErr- FatalErr- UnsuppReq- AuxPwr- TransPend- LnkCap: Port #0, Speed unknown, Width x0, ASPM unknown, Latency L0 <64ns, L1 <1us ClockPM- Suprise- LLActRep- BwNot- LnkCtl: ASPM Disabled; Disabled- Retrain- CommClk- ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt- LnkSta: Speed unknown, Width x0, TrErr- Train- SlotClk- DLActive- BWMgmt- ABWMgmt- Capabilities: [e0] Power Management version 3 Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-) Status: D0 PME-Enable- DSel=0 DScale=0 PME- 00:16.5 System peripheral: Intel Corporation 5520/5500/X58 Chipset QuickData Technology Device (rev 13) Subsystem: Super Micro Computer Inc Device 000b Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0, Cache Line Size: 64 bytes Interrupt: pin B routed to IRQ 10 Region 0: Memory at fbbe8000 (64-bit, non-prefetchable) [size=16K] Capabilities: [80] MSI-X: Enable- Mask- TabSize=1 Vector table: BAR=0 offset=00002000 PBA: BAR=0 offset=00003000 Capabilities: [90] Express (v2) Root Complex Integrated Endpoint, MSI 00 DevCap: MaxPayload 128 bytes, PhantFunc 0, Latency L0s <64ns, L1 <1us ExtTag- RBE+ FLReset- DevCtl: Report errors: Correctable- Non-Fatal- Fatal- Unsupported- RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop- MaxPayload 128 bytes, MaxReadReq 128 bytes DevSta: CorrErr- UncorrErr- FatalErr- UnsuppReq- AuxPwr- TransPend- LnkCap: Port #0, Speed unknown, Width x0, ASPM unknown, Latency L0 <64ns, L1 <1us ClockPM- Suprise- LLActRep- BwNot- LnkCtl: ASPM Disabled; Disabled- Retrain- CommClk- ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt- LnkSta: Speed unknown, Width x0, TrErr- Train- SlotClk- DLActive- BWMgmt- ABWMgmt- Capabilities: [e0] Power Management version 3 Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-) Status: D0 PME-Enable- DSel=0 DScale=0 PME- 00:16.6 System peripheral: Intel Corporation 5520/5500/X58 Chipset QuickData Technology Device (rev 13) Subsystem: Super Micro Computer Inc Device 000b Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0, Cache Line Size: 64 bytes Interrupt: pin C routed to IRQ 14 Region 0: Memory at fbbe4000 (64-bit, non-prefetchable) [size=16K] Capabilities: [80] MSI-X: Enable- Mask- TabSize=1 Vector table: BAR=0 offset=00002000 PBA: BAR=0 offset=00003000 Capabilities: [90] Express (v2) Root Complex Integrated Endpoint, MSI 00 DevCap: MaxPayload 128 bytes, PhantFunc 0, Latency L0s <64ns, L1 <1us ExtTag- RBE+ FLReset- DevCtl: Report errors: Correctable- Non-Fatal- Fatal- Unsupported- RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop- MaxPayload 128 bytes, MaxReadReq 128 bytes DevSta: CorrErr- UncorrErr- FatalErr- UnsuppReq- AuxPwr- TransPend- LnkCap: Port #0, Speed unknown, Width x0, ASPM unknown, Latency L0 <64ns, L1 <1us ClockPM- Suprise- LLActRep- BwNot- LnkCtl: ASPM Disabled; Disabled- Retrain- CommClk- ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt- LnkSta: Speed unknown, Width x0, TrErr- Train- SlotClk- DLActive- BWMgmt- ABWMgmt- Capabilities: [e0] Power Management version 3 Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-) Status: D0 PME-Enable- DSel=0 DScale=0 PME- 00:16.7 System peripheral: Intel Corporation 5520/5500/X58 Chipset QuickData Technology Device (rev 13) Subsystem: Super Micro Computer Inc Device 000b Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0, Cache Line Size: 64 bytes Interrupt: pin D routed to IRQ 15 Region 0: Memory at fbbe0000 (64-bit, non-prefetchable) [size=16K] Capabilities: [80] MSI-X: Enable- Mask- TabSize=1 Vector table: BAR=0 offset=00002000 PBA: BAR=0 offset=00003000 Capabilities: [90] Express (v2) Root Complex Integrated Endpoint, MSI 00 DevCap: MaxPayload 128 bytes, PhantFunc 0, Latency L0s <64ns, L1 <1us ExtTag- RBE+ FLReset- DevCtl: Report errors: Correctable- Non-Fatal- Fatal- Unsupported- RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop- MaxPayload 128 bytes, MaxReadReq 128 bytes DevSta: CorrErr- UncorrErr- FatalErr- UnsuppReq- AuxPwr- TransPend- LnkCap: Port #0, Speed unknown, Width x0, ASPM unknown, Latency L0 <64ns, L1 <1us ClockPM- Suprise- LLActRep- BwNot- LnkCtl: ASPM Disabled; Disabled- Retrain- CommClk- ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt- LnkSta: Speed unknown, Width x0, TrErr- Train- SlotClk- DLActive- BWMgmt- ABWMgmt- Capabilities: [e0] Power Management version 3 Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-) Status: D0 PME-Enable- DSel=0 DScale=0 PME- 00:1a.0 USB Controller: Intel Corporation 82801JI (ICH10 Family) USB UHCI Controller #4 (prog-if 00 [UHCI]) Subsystem: Super Micro Computer Inc Device 000b Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 Interrupt: pin A routed to IRQ 16 Region 4: I/O ports at ac00 [size=32] Capabilities: [50] PCIe advanced features <?> Kernel driver in use: uhci_hcd Kernel modules: uhci-hcd 00:1a.1 USB Controller: Intel Corporation 82801JI (ICH10 Family) USB UHCI Controller #5 (prog-if 00 [UHCI]) Subsystem: Super Micro Computer Inc Device 000b Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 Interrupt: pin B routed to IRQ 21 Region 4: I/O ports at a880 [size=32] Capabilities: [50] PCIe advanced features <?> Kernel driver in use: uhci_hcd Kernel modules: uhci-hcd 00:1a.2 USB Controller: Intel Corporation 82801JI (ICH10 Family) USB UHCI Controller #6 (prog-if 00 [UHCI]) Subsystem: Super Micro Computer Inc Device 000b Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 Interrupt: pin D routed to IRQ 19 Region 4: I/O ports at a800 [size=32] Capabilities: [50] PCIe advanced features <?> Kernel driver in use: uhci_hcd Kernel modules: uhci-hcd 00:1a.7 USB Controller: Intel Corporation 82801JI (ICH10 Family) USB2 EHCI Controller #2 (prog-if 20 [EHCI]) Subsystem: Super Micro Computer Inc Device 000b Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 Interrupt: pin C routed to IRQ 18 Region 0: Memory at fbbde000 (32-bit, non-prefetchable) [size=1K] Capabilities: [50] Power Management version 2 Flags: PMEClk- DSI- D1- D2- AuxCurrent=375mA PME(D0+,D1-,D2-,D3hot +,D3cold+) Status: D0 PME-Enable- DSel=0 DScale=0 PME- Capabilities: [58] Debug port: BAR=1 offset=00a0 Capabilities: [98] PCIe advanced features <?> Kernel driver in use: ehci_hcd Kernel modules: ehci-hcd 00:1b.0 Audio device: Intel Corporation 82801JI (ICH10 Family) HD Audio Controller Subsystem: Super Micro Computer Inc Device 000b Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0, Cache Line Size: 64 bytes Interrupt: pin A routed to IRQ 22 Region 0: Memory at fbbd8000 (64-bit, non-prefetchable) [size=16K] Capabilities: [50] Power Management version 2 Flags: PMEClk- DSI- D1- D2- AuxCurrent=55mA PME(D0+,D1-,D2-,D3hot +,D3cold+) Status: D0 PME-Enable- DSel=0 DScale=0 PME- Capabilities: [60] Message Signalled Interrupts: Mask- 64bit+ Queue=0/0 Enable- Address: 0000000000000000 Data: 0000 Capabilities: [70] Express (v1) Root Complex Integrated Endpoint, MSI 00 DevCap: MaxPayload 128 bytes, PhantFunc 0, Latency L0s <64ns, L1 <1us ExtTag- RBE- FLReset+ DevCtl: Report errors: Correctable- Non-Fatal- Fatal- Unsupported- RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop+ MaxPayload 128 bytes, MaxReadReq 128 bytes DevSta: CorrErr- UncorrErr- FatalErr- UnsuppReq- AuxPwr+ TransPend- LnkCap: Port #0, Speed unknown, Width x0, ASPM unknown, Latency L0 <64ns, L1 <1us ClockPM- Suprise- LLActRep- BwNot- LnkCtl: ASPM Disabled; Disabled- Retrain- CommClk- ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt- LnkSta: Speed unknown, Width x0, TrErr- Train- SlotClk- DLActive- BWMgmt- ABWMgmt- Capabilities: [100] Virtual Channel <?> Capabilities: [130] Root Complex Link <?> Kernel driver in use: HDA Intel Kernel modules: snd-hda-intel 00:1c.0 PCI bridge: Intel Corporation 82801JI (ICH10 Family) PCI Express Root Port 1 (prog-if 00 [Normal decode]) Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx+ Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0, Cache Line Size: 64 bytes Bus: primary=00, secondary=04, subordinate=06, sec-latency=0 I/O behind bridge: 0000f000-00000fff Memory behind bridge: fbc00000-fbcfffff Prefetchable memory behind bridge: 00000000f2f00000-00000000f2ffffff Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort+ <SERR- <PERR- BridgeCtl: Parity- SERR+ NoISA- VGA- MAbort- >Reset- FastB2B- PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn- Capabilities: [40] Express (v1) Root Port (Slot+), MSI 00 DevCap: MaxPayload 128 bytes, PhantFunc 0, Latency L0s <64ns, L1 <1us ExtTag- RBE+ FLReset- DevCtl: Report errors: Correctable- Non-Fatal- Fatal- Unsupported- RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop- MaxPayload 128 bytes, MaxReadReq 128 bytes DevSta: CorrErr+ UncorrErr- FatalErr- UnsuppReq- AuxPwr+ TransPend- LnkCap: Port #1, Speed 2.5GT/s, Width x4, ASPM L0s L1, Latency L0 <256ns, L1 <4us ClockPM- Suprise- LLActRep+ BwNot- LnkCtl: ASPM L0s L1 Enabled; RCB 64 bytes Disabled- Retrain- CommClk+ ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt- LnkSta: Speed 2.5GT/s, Width x4, TrErr- Train- SlotClk+ DLActive+ BWMgmt- ABWMgmt- SltCap: AttnBtn- PwrCtrl- MRL- AttnInd- PwrInd- HotPlug+ Surpise+ Slot # 0, PowerLimit 25.000000; Interlock- NoCompl- SltCtl: Enable: AttnBtn- PwrFlt- MRL- PresDet- CmdCplt- HPIrq- LinkChg- Control: AttnInd Unknown, PwrInd Unknown, Power- Interlock- SltSta: Status: AttnBtn- PowerFlt- MRL- CmdCplt- PresDet+ Interlock- Changed: MRL- PresDet+ LinkState+ RootCtl: ErrCorrectable- ErrNon-Fatal- ErrFatal- PMEIntEna- CRSVisible- RootCap: CRSVisible- RootSta: PME ReqID 0000, PMEStatus- PMEPending- Capabilities: [80] Message Signalled Interrupts: Mask- 64bit- Queue=0/0 Enable+ Address: fee00000 Data: 40c8 Capabilities: [90] Subsystem: Super Micro Computer Inc Device 000b Capabilities: [a0] Power Management version 2 Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0+,D1-,D2-,D3hot +,D3cold+) Status: D0 PME-Enable- DSel=0 DScale=0 PME- Capabilities: [100] Virtual Channel <?> Capabilities: [180] Root Complex Link <?> Kernel driver in use: pcieport-driver Kernel modules: shpchp 00:1c.4 PCI bridge: Intel Corporation 82801JI (ICH10 Family) PCI Express Root Port 5 (prog-if 00 [Normal decode]) Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx+ Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0, Cache Line Size: 64 bytes Bus: primary=00, secondary=07, subordinate=07, sec-latency=0 I/O behind bridge: 0000d000-0000dfff Memory behind bridge: fbd00000-fbdfffff Prefetchable memory behind bridge: 00000000fff00000-00000000000fffff Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- <SERR- <PERR- BridgeCtl: Parity- SERR+ NoISA- VGA- MAbort- >Reset- FastB2B- PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn- Capabilities: [40] Express (v1) Root Port (Slot+), MSI 00 DevCap: MaxPayload 128 bytes, PhantFunc 0, Latency L0s <64ns, L1 <1us ExtTag- RBE+ FLReset- DevCtl: Report errors: Correctable- Non-Fatal- Fatal- Unsupported- RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop- MaxPayload 128 bytes, MaxReadReq 128 bytes DevSta: CorrErr+ UncorrErr- FatalErr- UnsuppReq- AuxPwr+ TransPend- LnkCap: Port #5, Speed 2.5GT/s, Width x1, ASPM L0s L1, Latency L0 <256ns, L1 <4us ClockPM- Suprise- LLActRep+ BwNot- LnkCtl: ASPM L0s L1 Enabled; RCB 64 bytes Disabled- Retrain- CommClk+ ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt- LnkSta: Speed 2.5GT/s, Width x1, TrErr- Train- SlotClk+ DLActive+ BWMgmt- ABWMgmt- SltCap: AttnBtn- PwrCtrl- MRL- AttnInd- PwrInd- HotPlug+ Surpise+ Slot # 0, PowerLimit 10.000000; Interlock- NoCompl- SltCtl: Enable: AttnBtn- PwrFlt- MRL- PresDet- CmdCplt- HPIrq- LinkChg- Control: AttnInd Unknown, PwrInd Unknown, Power- Interlock- SltSta: Status: AttnBtn- PowerFlt- MRL- CmdCplt- PresDet+ Interlock- Changed: MRL- PresDet+ LinkState+ RootCtl: ErrCorrectable- ErrNon-Fatal- ErrFatal- PMEIntEna- CRSVisible- RootCap: CRSVisible- RootSta: PME ReqID 0000, PMEStatus- PMEPending- Capabilities: [80] Message Signalled Interrupts: Mask- 64bit- Queue=0/0 Enable+ Address: fee00000 Data: 40d0 Capabilities: [90] Subsystem: Super Micro Computer Inc Device 000b Capabilities: [a0] Power Management version 2 Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0+,D1-,D2-,D3hot +,D3cold+) Status: D0 PME-Enable- DSel=0 DScale=0 PME- Capabilities: [100] Virtual Channel <?> Capabilities: [180] Root Complex Link <?> Kernel driver in use: pcieport-driver Kernel modules: shpchp 00:1c.5 PCI bridge: Intel Corporation 82801JI (ICH10 Family) PCI Express Root Port 6 (prog-if 00 [Normal decode]) Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx+ Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0, Cache Line Size: 64 bytes Bus: primary=00, secondary=08, subordinate=08, sec-latency=0 I/O behind bridge: 0000e000-0000efff Memory behind bridge: fbe00000-fbefffff Prefetchable memory behind bridge: 00000000fff00000-00000000000fffff Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- <SERR- <PERR- BridgeCtl: Parity- SERR+ NoISA- VGA- MAbort- >Reset- FastB2B- PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn- Capabilities: [40] Express (v1) Root Port (Slot+), MSI 00 DevCap: MaxPayload 128 bytes, PhantFunc 0, Latency L0s <64ns, L1 <1us ExtTag- RBE+ FLReset- DevCtl: Report errors: Correctable- Non-Fatal- Fatal- Unsupported- RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop- MaxPayload 128 bytes, MaxReadReq 128 bytes DevSta: CorrErr+ UncorrErr- FatalErr- UnsuppReq- AuxPwr+ TransPend- LnkCap: Port #6, Speed 2.5GT/s, Width x1, ASPM L0s L1, Latency L0 <256ns, L1 <4us ClockPM- Suprise- LLActRep+ BwNot- LnkCtl: ASPM L0s L1 Enabled; RCB 64 bytes Disabled- Retrain- CommClk+ ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt- LnkSta: Speed 2.5GT/s, Width x1, TrErr- Train- SlotClk+ DLActive+ BWMgmt- ABWMgmt- SltCap: AttnBtn- PwrCtrl- MRL- AttnInd- PwrInd- HotPlug+ Surpise+ Slot # 0, PowerLimit 10.000000; Interlock- NoCompl- SltCtl: Enable: AttnBtn- PwrFlt- MRL- PresDet- CmdCplt- HPIrq- LinkChg- Control: AttnInd Unknown, PwrInd Unknown, Power- Interlock- SltSta: Status: AttnBtn- PowerFlt- MRL- CmdCplt- PresDet+ Interlock- Changed: MRL- PresDet+ LinkState+ RootCtl: ErrCorrectable- ErrNon-Fatal- ErrFatal- PMEIntEna- CRSVisible- RootCap: CRSVisible- RootSta: PME ReqID 0000, PMEStatus- PMEPending- Capabilities: [80] Message Signalled Interrupts: Mask- 64bit- Queue=0/0 Enable+ Address: fee00000 Data: 40d8 Capabilities: [90] Subsystem: Super Micro Computer Inc Device 000b Capabilities: [a0] Power Management version 2 Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0+,D1-,D2-,D3hot +,D3cold+) Status: D0 PME-Enable- DSel=0 DScale=0 PME- Capabilities: [100] Virtual Channel <?> Capabilities: [180] Root Complex Link <?> Kernel driver in use: pcieport-driver Kernel modules: shpchp 00:1d.0 USB Controller: Intel Corporation 82801JI (ICH10 Family) USB UHCI Controller #1 (prog-if 00 [UHCI]) Subsystem: Super Micro Computer Inc Device 000b Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 Interrupt: pin A routed to IRQ 23 Region 4: I/O ports at a480 [size=32] Capabilities: [50] PCIe advanced features <?> Kernel driver in use: uhci_hcd Kernel modules: uhci-hcd 00:1d.1 USB Controller: Intel Corporation 82801JI (ICH10 Family) USB UHCI Controller #2 (prog-if 00 [UHCI]) Subsystem: Super Micro Computer Inc Device 000b Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 Interrupt: pin B routed to IRQ 19 Region 4: I/O ports at a400 [size=32] Capabilities: [50] PCIe advanced features <?> Kernel driver in use: uhci_hcd Kernel modules: uhci-hcd 00:1d.2 USB Controller: Intel Corporation 82801JI (ICH10 Family) USB UHCI Controller #3 (prog-if 00 [UHCI]) Subsystem: Super Micro Computer Inc Device 000b Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 Interrupt: pin C routed to IRQ 18 Region 4: I/O ports at a080 [size=32] Capabilities: [50] PCIe advanced features <?> Kernel driver in use: uhci_hcd Kernel modules: uhci-hcd 00:1d.7 USB Controller: Intel Corporation 82801JI (ICH10 Family) USB2 EHCI Controller #1 (prog-if 20 [EHCI]) Subsystem: Super Micro Computer Inc Device 000b Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 Interrupt: pin A routed to IRQ 23 Region 0: Memory at fbbdc000 (32-bit, non-prefetchable) [size=1K] Capabilities: [50] Power Management version 2 Flags: PMEClk- DSI- D1- D2- AuxCurrent=375mA PME(D0+,D1-,D2-,D3hot +,D3cold+) Status: D0 PME-Enable- DSel=0 DScale=0 PME- Capabilities: [58] Debug port: BAR=1 offset=00a0 Capabilities: [98] PCIe advanced features <?> Kernel driver in use: ehci_hcd Kernel modules: ehci-hcd 00:1e.0 PCI bridge: Intel Corporation 82801 PCI Bridge (rev 90) (prog-if 01 [Subtractive decode]) Control: I/O- Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 Bus: primary=00, secondary=09, subordinate=09, sec-latency=32 I/O behind bridge: 0000f000-00000fff Memory behind bridge: fff00000-000fffff Prefetchable memory behind bridge: 00000000fff00000-00000000000fffff Secondary status: 66MHz- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort+ <SERR- <PERR- BridgeCtl: Parity- SERR+ NoISA- VGA- MAbort- >Reset- FastB2B- PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn- Capabilities: [50] Subsystem: Super Micro Computer Inc Device 000b 00:1f.0 ISA bridge: Intel Corporation 82801JIR (ICH10R) LPC Interface Controller Subsystem: Super Micro Computer Inc Device 000b Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 Capabilities: [e0] Vendor Specific Information <?> Kernel modules: iTCO_wdt 00:1f.2 SATA controller: Intel Corporation 82801JI (ICH10 Family) SATA AHCI Controller (prog-if 01 [AHCI 1.0]) Subsystem: Super Micro Computer Inc Device 000b Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+ Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 Interrupt: pin B routed to IRQ 758 Region 0: I/O ports at a000 [size=8] Region 1: I/O ports at 9c00 [size=4] Region 2: I/O ports at 9880 [size=8] Region 3: I/O ports at 9800 [size=4] Region 4: I/O ports at 9480 [size=32] Region 5: Memory at fbbd6000 (32-bit, non-prefetchable) [size=2K] Capabilities: [80] Message Signalled Interrupts: Mask- 64bit- Queue=0/4 Enable+ Address: fee14000 Data: 4089 Capabilities: [70] Power Management version 3 Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot +,D3cold-) Status: D0 PME-Enable- DSel=0 DScale=0 PME- Capabilities: [a8] SATA HBA <?> Capabilities: [b0] PCIe advanced features <?> Kernel driver in use: ahci Kernel modules: ahci 00:1f.3 SMBus: Intel Corporation 82801JI (ICH10 Family) SMBus Controller Subsystem: Super Micro Computer Inc Device 000b Control: I/O+ Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Interrupt: pin C routed to IRQ 18 Region 0: Memory at fbbd4000 (64-bit, non-prefetchable) [size=256] Region 4: I/O ports at 0400 [size=32] Kernel driver in use: i801_smbus Kernel modules: i2c-i801 01:00.0 VGA compatible controller: nVidia Corporation G86 [Quadro NVS 290] (rev a1) (prog-if 00 [VGA controller]) Subsystem: nVidia Corporation Device 0492 Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr+ Stepping- SERR- FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 Interrupt: pin A routed to IRQ 16 Region 0: Memory at f6000000 (32-bit, non-prefetchable) [size=16M] Region 1: Memory at c0000000 (64-bit, prefetchable) [size=256M] Region 3: Memory at f4000000 (64-bit, non-prefetchable) [size=32M] Region 5: I/O ports at bc00 [disabled] [size=128] [virtual] Expansion ROM at f3fe0000 [disabled] [size=128K] Capabilities: [60] Power Management version 2 Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-) Status: D0 PME-Enable- DSel=0 DScale=0 PME- Capabilities: [68] Message Signalled Interrupts: Mask- 64bit+ Queue=0/0 Enable- Address: 0000000000000000 Data: 0000 Capabilities: [78] Express (v1) Endpoint, MSI 00 DevCap: MaxPayload 128 bytes, PhantFunc 0, Latency L0s <512ns, L1 <4us ExtTag+ AttnBtn- AttnInd- PwrInd- RBE+ FLReset- DevCtl: Report errors: Correctable- Non-Fatal- Fatal- Unsupported- RlxdOrd+ ExtTag+ PhantFunc- AuxPwr- NoSnoop+ MaxPayload 128 bytes, MaxReadReq 512 bytes DevSta: CorrErr- UncorrErr- FatalErr- UnsuppReq- AuxPwr- TransPend- LnkCap: Port #0, Speed 2.5GT/s, Width x16, ASPM L0s L1, Latency L0 <512ns, L1 <4us ClockPM- Suprise- LLActRep- BwNot- LnkCtl: ASPM L0s Enabled; RCB 128 bytes Disabled- Retrain- CommClk+ ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt- LnkSta: Speed 2.5GT/s, Width x4, TrErr- Train- SlotClk+ DLActive- BWMgmt- ABWMgmt- Capabilities: [100] Virtual Channel <?> Capabilities: [128] Power Budgeting <?> Capabilities: [600] Vendor Specific Information <?> Kernel driver in use: nvidia Kernel modules: nvidia, nvidiafb 03:00.0 VGA compatible controller: nVidia Corporation Device 06fd (rev a1) (prog-if 00 [VGA controller]) Subsystem: nVidia Corporation Device 062e Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr+ Stepping- SERR- FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 Interrupt: pin A routed to IRQ 16 Region 0: Memory at fa000000 (32-bit, non-prefetchable) [size=16M] Region 1: Memory at d0000000 (64-bit, prefetchable) [size=256M] Region 3: Memory at f8000000 (64-bit, non-prefetchable) [size=32M] Region 5: I/O ports at cc00 [size=128] [virtual] Expansion ROM at f7fe0000 [disabled] [size=128K] Capabilities: [60] Power Management version 3 Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-) Status: D0 PME-Enable- DSel=0 DScale=0 PME- Capabilities: [68] Message Signalled Interrupts: Mask- 64bit+ Queue=0/0 Enable- Address: 0000000000000000 Data: 0000 Capabilities: [78] Express (v2) Endpoint, MSI 00 DevCap: MaxPayload 128 bytes, PhantFunc 0, Latency L0s <512ns, L1 <4us ExtTag+ AttnBtn- AttnInd- PwrInd- RBE+ FLReset- DevCtl: Report errors: Correctable- Non-Fatal- Fatal- Unsupported- RlxdOrd+ ExtTag+ PhantFunc- AuxPwr- NoSnoop+ MaxPayload 128 bytes, MaxReadReq 512 bytes DevSta: CorrErr+ UncorrErr- FatalErr- UnsuppReq- AuxPwr- TransPend+ LnkCap: Port #0, Speed 5GT/s, Width x16, ASPM L0s L1, Latency L0 <256ns, L1 <1us ClockPM- Suprise- LLActRep- BwNot- LnkCtl: ASPM L0s Enabled; RCB 128 bytes Disabled- Retrain- CommClk+ ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt- LnkSta: Speed 5GT/s, Width x16, TrErr- Train- SlotClk+ DLActive- BWMgmt- ABWMgmt- Capabilities: [100] Virtual Channel <?> Capabilities: [128] Power Budgeting <?> Capabilities: [600] Vendor Specific Information <?> Kernel driver in use: nvidia Kernel modules: nvidia, nvidiafb 04:00.0 PCI bridge: Intel Corporation 80333 Segment-A PCI Express-to-PCI Express Bridge (prog-if 00 [Normal decode]) Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0, Cache Line Size: 64 bytes Bus: primary=04, secondary=05, subordinate=05, sec-latency=64 I/O behind bridge: 0000f000-00000fff Memory behind bridge: fbc00000-fbcfffff Prefetchable memory behind bridge: 00000000f2f00000-00000000f2ffffff Secondary status: 66MHz+ FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort+ <SERR- <PERR- BridgeCtl: Parity- SERR+ NoISA- VGA- MAbort- >Reset- FastB2B- PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn- Capabilities: [44] Express (v1) PCI/PCI-X Bridge, MSI 00 DevCap: MaxPayload 256 bytes, PhantFunc 0, Latency L0s <64ns, L1 <1us ExtTag- AttnBtn- AttnInd- PwrInd- RBE- FLReset- DevCtl: Report errors: Correctable- Non-Fatal- Fatal- Unsupported- RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop- BrConfRtry+ MaxPayload 128 bytes, MaxReadReq 512 bytes DevSta: CorrErr+ UncorrErr+ FatalErr- UnsuppReq+ AuxPwr- TransPend- LnkCap: Port #0, Speed 2.5GT/s, Width x8, ASPM L0s, Latency L0 unlimited, L1 unlimited ClockPM- Suprise- LLActRep- BwNot- LnkCtl: ASPM L0s L1 Enabled; Disabled- Retrain- CommClk- ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt- LnkSta: Speed 2.5GT/s, Width x4, TrErr- Train- SlotClk- DLActive- BWMgmt- ABWMgmt- Capabilities: [5c] Message Signalled Interrupts: Mask- 64bit+ Queue=0/0 Enable- Address: 0000000000000000 Data: 0000 Capabilities: [6c] Power Management version 2 Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0+,D1-,D2-,D3hot +,D3cold+) Status: D0 PME-Enable- DSel=0 DScale=0 PME- Capabilities: [d8] PCI-X bridge device Secondary Status: 64bit+ 133MHz+ SCD- USC- SCO- SRD- Freq=133MHz Status: Dev=04:00.0 64bit- 133MHz- SCD- USC- SCO- SRD- Upstream: Capacity=65535 CommitmentLimit=65535 Downstream: Capacity=65535 CommitmentLimit=65535 Capabilities: [100] Advanced Error Reporting <?> Capabilities: [300] Power Budgeting <?> Kernel modules: shpchp 04:00.2 PCI bridge: Intel Corporation 80333 Segment-B PCI Express-to-PCI Express Bridge (prog-if 00 [Normal decode]) Control: I/O- Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0, Cache Line Size: 64 bytes Bus: primary=04, secondary=06, subordinate=06, sec-latency=64 I/O behind bridge: 0000f000-00000fff Memory behind bridge: fff00000-000fffff Prefetchable memory behind bridge: 00000000fff00000-00000000000fffff Secondary status: 66MHz+ FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort+ <SERR- <PERR- BridgeCtl: Parity- SERR+ NoISA- VGA- MAbort- >Reset- FastB2B- PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn- Capabilities: [44] Express (v1) PCI/PCI-X Bridge, MSI 00 DevCap: MaxPayload 256 bytes, PhantFunc 0, Latency L0s <64ns, L1 <1us ExtTag- AttnBtn- AttnInd- PwrInd- RBE- FLReset- DevCtl: Report errors: Correctable- Non-Fatal- Fatal- Unsupported- RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop- BrConfRtry- MaxPayload 128 bytes, MaxReadReq 512 bytes DevSta: CorrErr+ UncorrErr+ FatalErr- UnsuppReq+ AuxPwr- TransPend- LnkCap: Port #0, Speed 2.5GT/s, Width x8, ASPM L0s, Latency L0 unlimited, L1 unlimited ClockPM- Suprise- LLActRep- BwNot- LnkCtl: ASPM L0s L1 Enabled; Disabled- Retrain- CommClk- ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt- LnkSta: Speed 2.5GT/s, Width x4, TrErr- Train- SlotClk- DLActive- BWMgmt- ABWMgmt- Capabilities: [5c] Message Signalled Interrupts: Mask- 64bit+ Queue=0/0 Enable- Address: 0000000000000000 Data: 0000 Capabilities: [6c] Power Management version 2 Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0+,D1-,D2-,D3hot +,D3cold+) Status: D0 PME-Enable- DSel=0 DScale=0 PME- Capabilities: [d8] PCI-X bridge device Secondary Status: 64bit+ 133MHz+ SCD- USC- SCO- SRD- Freq=133MHz Status: Dev=04:00.2 64bit- 133MHz- SCD- USC- SCO- SRD- Upstream: Capacity=65535 CommitmentLimit=65535 Downstream: Capacity=65535 CommitmentLimit=65535 Capabilities: [100] Advanced Error Reporting <?> Capabilities: [300] Power Budgeting <?> Kernel modules: shpchp 05:0e.0 RAID bus controller: Dell PowerEdge Expandable RAID controller 5 Subsystem: Dell PERC 5/i Integrated RAID Controller Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping+ SERR- FastB2B- DisINTx- Status: Cap+ 66MHz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 64 (32000ns min), Cache Line Size: 64 bytes Interrupt: pin A routed to IRQ 18 Region 0: Memory at f2ff0000 (32-bit, prefetchable) [size=64K] Region 2: Memory at fbce0000 (32-bit, non-prefetchable) [size=128K] Expansion ROM at fbcd0000 [disabled] [size=32K] Capabilities: [c0] Power Management version 2 Flags: PMEClk- DSI- D1+ D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-) Status: D0 PME-Enable- DSel=0 DScale=0 PME- Capabilities: [d0] Message Signalled Interrupts: Mask- 64bit+ Queue=0/1 Enable- Address: 0000000000000000 Data: 0000 Capabilities: [e0] PCI-X non-bridge device Command: DPERE- ERO- RBC=512 OST=4 Status: Dev=05:0e.0 64bit+ 133MHz+ SCD- USC- DC=bridge DMMRBC=1024 DMOST=4 DMCRS=16 RSCEM- 266MHz- 533MHz- Kernel driver in use: megaraid_sas Kernel modules: megaraid_sas 07:00.0 Ethernet controller: Intel Corporation 82574L Gigabit Network Connection Subsystem: Super Micro Computer Inc Device 10d3 Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+ Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx+ Latency: 0, Cache Line Size: 64 bytes Interrupt: pin A routed to IRQ 16 Region 0: Memory at fbde0000 (32-bit, non-prefetchable) [size=128K] Region 2: I/O ports at dc00 [size=32] Region 3: Memory at fbddc000 (32-bit, non-prefetchable) [size=16K] Capabilities: [c8] Power Management version 2 Flags: PMEClk- DSI+ D1- D2- AuxCurrent=0mA PME(D0+,D1-,D2-,D3hot +,D3cold+) Status: D0 PME-Enable- DSel=0 DScale=1 PME- Capabilities: [d0] Message Signalled Interrupts: Mask- 64bit+ Queue=0/0 Enable- Address: 0000000000000000 Data: 0000 Capabilities: [e0] Express (v1) Endpoint, MSI 00 DevCap: MaxPayload 256 bytes, PhantFunc 0, Latency L0s <512ns, L1 <64us ExtTag- AttnBtn- AttnInd- PwrInd- RBE+ FLReset- DevCtl: Report errors: Correctable- Non-Fatal- Fatal- Unsupported- RlxdOrd+ ExtTag- PhantFunc- AuxPwr- NoSnoop+ MaxPayload 128 bytes, MaxReadReq 512 bytes DevSta: CorrErr+ UncorrErr- FatalErr- UnsuppReq+ AuxPwr+ TransPend- LnkCap: Port #0, Speed 2.5GT/s, Width x1, ASPM L0s L1, Latency L0 <128ns, L1 <64us ClockPM- Suprise- LLActRep- BwNot- LnkCtl: ASPM L0s Enabled; RCB 64 bytes Disabled- Retrain- CommClk+ ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt- LnkSta: Speed 2.5GT/s, Width x1, TrErr- Train- SlotClk+ DLActive- BWMgmt- ABWMgmt- Capabilities: [a0] MSI-X: Enable+ Mask- TabSize=5 Vector table: BAR=3 offset=00000000 PBA: BAR=3 offset=00002000 Capabilities: [100] Advanced Error Reporting <?> Kernel driver in use: e1000e Kernel modules: e1000e 08:00.0 Ethernet controller: Intel Corporation 82574L Gigabit Network Connection Subsystem: Super Micro Computer Inc Device 10d3 Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+ Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0, Cache Line Size: 64 bytes Interrupt: pin A routed to IRQ 17 Region 0: Memory at fbee0000 (32-bit, non-prefetchable) [size=128K] Region 2: I/O ports at ec00 [size=32] Region 3: Memory at fbedc000 (32-bit, non-prefetchable) [size=16K] Capabilities: [c8] Power Management version 2 Flags: PMEClk- DSI+ D1- D2- AuxCurrent=0mA PME(D0+,D1-,D2-,D3hot +,D3cold+) Status: D0 PME-Enable- DSel=0 DScale=1 PME- Capabilities: [d0] Message Signalled Interrupts: Mask- 64bit+ Queue=0/0 Enable- Address: 0000000000000000 Data: 0000 Capabilities: [e0] Express (v1) Endpoint, MSI 00 DevCap: MaxPayload 256 bytes, PhantFunc 0, Latency L0s <512ns, L1 <64us ExtTag- AttnBtn- AttnInd- PwrInd- RBE+ FLReset- DevCtl: Report errors: Correctable- Non-Fatal- Fatal- Unsupported- RlxdOrd+ ExtTag- PhantFunc- AuxPwr- NoSnoop+ MaxPayload 128 bytes, MaxReadReq 512 bytes DevSta: CorrErr+ UncorrErr- FatalErr- UnsuppReq+ AuxPwr+ TransPend- LnkCap: Port #0, Speed 2.5GT/s, Width x1, ASPM L0s L1, Latency L0 <128ns, L1 <64us ClockPM- Suprise- LLActRep- BwNot- LnkCtl: ASPM L0s Enabled; RCB 64 bytes Disabled- Retrain- CommClk+ ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt- LnkSta: Speed 2.5GT/s, Width x1, TrErr- Train- SlotClk+ DLActive- BWMgmt- ABWMgmt- Capabilities: [a0] MSI-X: Enable+ Mask- TabSize=5 Vector table: BAR=3 offset=00000000 PBA: BAR=3 offset=00002000 Capabilities: [100] Advanced Error Reporting <?> Kernel driver in use: e1000e Kernel modules: e1000e On Wed, 2010-06-02 at 09:23 +0800, Weidong Han wrote:> > > > > This PCI-x card is not suitable for assignment. It contains an > invisible > device 05:08.0 (lspci cannot show it), but this invisible device > won''t > be mapped by VT-d because VT-d engine doesn''t know this device, so > you > can see the DMAR faults on it. One workaround is to hard code to map > 05:08.0 when assign 05:0e.0. BTW, PCIe LSI card don''t have this > problem. >_______________________________________________ Xen-devel mailing list Xen-devel@lists.xensource.com http://lists.xensource.com/xen-devel
Han, Weidong
2010-Jun-02 01:56 UTC
RE: [Xen-devel] iommuu/vt-d issues with LSI MegaSAS (PERC5i)
I mean 05:0e.0 is not a PCIe Endpoint device. Although you insert it in PCIe
slot, but it contains two PCI bridges 04:00.0 and 04:00.2, device 05:0e.0 is
behind bridge 04:00.0. Actually we used this device before, and encountered the
same issue. Now we are using a newer SLI card.
I think you can try the workaround I mentioned below.
Regards,
Weidong
-----Original Message-----
From: M. Nunberg [mailto:mnunberg@haskalah.org]
Sent: Wednesday, June 02, 2010 9:40 AM
To: Han, Weidong
Cc: Xen-devel
Subject: Re: [Xen-devel] iommuu/vt-d issues with LSI MegaSAS (PERC5i)
The card is PCIe, not PCI-X; I might note that this card is an x8 card
in an x4 slot.. I do not think this is an issue, but maybe...
Booting with limiting the memory uunder 4GB, bare metal + DMAR, swiotlb
etc. all fail.. I can send the log in another post (whiich I will do
shortly)
Here is the full lspci -vvv output:
00:00.0 Host bridge: Intel Corporation 5500 I/O Hub to ESI Port (rev 13)
Subsystem: Super Micro Computer Inc Device 000b
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort-
<TAbort-
<MAbort- >SERR- <PERR- INTx-
Capabilities: [60] Message Signalled Interrupts: Mask+ 64bit- Queue=0/1
Enable-
Address: 00000000 Data: 0000
Masking: 00000000 Pending: 00000000
Capabilities: [90] Express (v2) Root Port (Slot-), MSI 00
DevCap: MaxPayload 128 bytes, PhantFunc 0, Latency L0s <64ns,
L1 <1us
ExtTag+ RBE+ FLReset-
DevCtl: Report errors: Correctable- Non-Fatal- Fatal-
Unsupported-
RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop-
MaxPayload 128 bytes, MaxReadReq 128 bytes
DevSta: CorrErr- UncorrErr- FatalErr- UnsuppReq- AuxPwr-
TransPend-
LnkCap: Port #0, Speed 2.5GT/s, Width x4, ASPM L0s L1, Latency
L0
<512ns, L1 <64us
ClockPM- Suprise+ LLActRep+ BwNot+
LnkCtl: ASPM Disabled; RCB 64 bytes Disabled- Retrain- CommClk-
ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
LnkSta: Speed 2.5GT/s, Width x4, TrErr- Train- SlotClk+
DLActive+
BWMgmt- ABWMgmt-
RootCtl: ErrCorrectable- ErrNon-Fatal- ErrFatal- PMEIntEna-
CRSVisible-
RootCap: CRSVisible-
RootSta: PME ReqID 0000, PMEStatus- PMEPending-
Capabilities: [e0] Power Management version 3
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0+,D1-,D2-,D3hot
+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [100] Advanced Error Reporting <?>
Capabilities: [150] Access Controls <?>
Capabilities: [160] Vendor Specific Information <?>
00:01.0 PCI bridge: Intel Corporation 5520/5500/X58 I/O Hub PCI Express
Root Port 1 (rev 13) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR+ FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort-
<TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Bus: primary=00, secondary=01, subordinate=01, sec-latency=0
I/O behind bridge: 0000b000-0000bfff
Memory behind bridge: f3f00000-f6ffffff
Prefetchable memory behind bridge: 00000000c0000000-00000000cfffffff
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort-
<TAbort-
<MAbort+ <SERR- <PERR-
BridgeCtl: Parity- SERR+ NoISA- VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: [40] Subsystem: Super Micro Computer Inc Device 000b
Capabilities: [60] Message Signalled Interrupts: Mask+ 64bit- Queue=0/1
Enable+
Address: fee00000 Data: 40b0
Masking: 00000003 Pending: 00000000
Capabilities: [90] Express (v2) Root Port (Slot+), MSI 00
DevCap: MaxPayload 256 bytes, PhantFunc 0, Latency L0s <64ns,
L1 <1us
ExtTag+ RBE+ FLReset-
DevCtl: Report errors: Correctable+ Non-Fatal+ Fatal+
Unsupported-
RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop-
MaxPayload 128 bytes, MaxReadReq 128 bytes
DevSta: CorrErr+ UncorrErr- FatalErr- UnsuppReq- AuxPwr-
TransPend-
LnkCap: Port #0, Speed 5GT/s, Width x4, ASPM L0s L1, Latency L0
<512ns, L1 <64us
ClockPM- Suprise+ LLActRep+ BwNot+
LnkCtl: ASPM L0s Enabled; RCB 64 bytes Disabled- Retrain-
CommClk+
ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
LnkSta: Speed 2.5GT/s, Width x4, TrErr- Train- SlotClk+
DLActive+
BWMgmt+ ABWMgmt-
SltCap: AttnBtn- PwrCtrl- MRL- AttnInd- PwrInd- HotPlug-
Surpise-
Slot # 2, PowerLimit 25.000000; Interlock- NoCompl-
SltCtl: Enable: AttnBtn- PwrFlt- MRL- PresDet- CmdCplt- HPIrq-
LinkChg-
Control: AttnInd Off, PwrInd Off, Power- Interlock-
SltSta: Status: AttnBtn- PowerFlt- MRL- CmdCplt- PresDet+
Interlock-
Changed: MRL- PresDet+ LinkState+
RootCtl: ErrCorrectable+ ErrNon-Fatal+ ErrFatal+ PMEIntEna-
CRSVisible-
RootCap: CRSVisible-
RootSta: PME ReqID 0000, PMEStatus- PMEPending-
Capabilities: [e0] Power Management version 3
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0+,D1-,D2-,D3hot
+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [100] Advanced Error Reporting <?>
Capabilities: [150] Access Controls <?>
Capabilities: [160] Vendor Specific Information <?>
Kernel driver in use: pcieport-driver
Kernel modules: shpchp
00:03.0 PCI bridge: Intel Corporation 5520/5500/X58 I/O Hub PCI Express
Root Port 3 (rev 13) (prog-if 00 [Normal decode])
Control: I/O- Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR+ FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort-
<TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Bus: primary=00, secondary=02, subordinate=02, sec-latency=0
I/O behind bridge: 0000f000-00000fff
Memory behind bridge: fff00000-000fffff
Prefetchable memory behind bridge: 00000000fff00000-00000000000fffff
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort-
<TAbort-
<MAbort- <SERR- <PERR-
BridgeCtl: Parity- SERR+ NoISA- VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: [40] Subsystem: Super Micro Computer Inc Device 000b
Capabilities: [60] Message Signalled Interrupts: Mask+ 64bit- Queue=0/1
Enable+
Address: fee00000 Data: 40b8
Masking: 00000003 Pending: 00000000
Capabilities: [90] Express (v2) Root Port (Slot+), MSI 00
DevCap: MaxPayload 256 bytes, PhantFunc 0, Latency L0s <64ns,
L1 <1us
ExtTag+ RBE+ FLReset-
DevCtl: Report errors: Correctable+ Non-Fatal+ Fatal+
Unsupported-
RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop-
MaxPayload 128 bytes, MaxReadReq 128 bytes
DevSta: CorrErr- UncorrErr- FatalErr- UnsuppReq- AuxPwr-
TransPend-
LnkCap: Port #0, Speed 5GT/s, Width x4, ASPM L0s L1, Latency L0
<512ns, L1 <64us
ClockPM- Suprise+ LLActRep+ BwNot+
LnkCtl: ASPM Disabled; RCB 64 bytes Disabled- Retrain- CommClk+
ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
LnkSta: Speed 2.5GT/s, Width x0, TrErr- Train- SlotClk+
DLActive-
BWMgmt- ABWMgmt-
SltCap: AttnBtn- PwrCtrl- MRL- AttnInd- PwrInd- HotPlug-
Surpise-
Slot # 33, PowerLimit 25.000000; Interlock- NoCompl-
SltCtl: Enable: AttnBtn- PwrFlt- MRL- PresDet- CmdCplt- HPIrq-
LinkChg-
Control: AttnInd Off, PwrInd Off, Power- Interlock-
SltSta: Status: AttnBtn- PowerFlt- MRL- CmdCplt- PresDet-
Interlock-
Changed: MRL- PresDet+ LinkState-
RootCtl: ErrCorrectable+ ErrNon-Fatal+ ErrFatal+ PMEIntEna-
CRSVisible-
RootCap: CRSVisible-
RootSta: PME ReqID 0000, PMEStatus- PMEPending-
Capabilities: [e0] Power Management version 3
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0+,D1-,D2-,D3hot
+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [100] Advanced Error Reporting <?>
Capabilities: [150] Access Controls <?>
Capabilities: [160] Vendor Specific Information <?>
Kernel driver in use: pcieport-driver
Kernel modules: shpchp
00:07.0 PCI bridge: Intel Corporation 5520/5500/X58 I/O Hub PCI Express
Root Port 7 (rev 13) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR+ FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort-
<TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Bus: primary=00, secondary=03, subordinate=03, sec-latency=0
I/O behind bridge: 0000c000-0000cfff
Memory behind bridge: f7f00000-faffffff
Prefetchable memory behind bridge: 00000000d0000000-00000000dfffffff
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort-
<TAbort-
<MAbort- <SERR- <PERR-
BridgeCtl: Parity- SERR+ NoISA- VGA+ MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: [40] Subsystem: Super Micro Computer Inc Device 000b
Capabilities: [60] Message Signalled Interrupts: Mask+ 64bit- Queue=0/1
Enable+
Address: fee00000 Data: 40c0
Masking: 00000003 Pending: 00000000
Capabilities: [90] Express (v2) Root Port (Slot+), MSI 00
DevCap: MaxPayload 256 bytes, PhantFunc 0, Latency L0s <64ns,
L1 <1us
ExtTag+ RBE+ FLReset-
DevCtl: Report errors: Correctable+ Non-Fatal+ Fatal+
Unsupported-
RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop-
MaxPayload 128 bytes, MaxReadReq 128 bytes
DevSta: CorrErr- UncorrErr- FatalErr- UnsuppReq- AuxPwr-
TransPend-
LnkCap: Port #0, Speed 5GT/s, Width x16, ASPM L0s L1, Latency L0
<512ns, L1 <64us
ClockPM- Suprise+ LLActRep+ BwNot+
LnkCtl: ASPM L0s Enabled; RCB 64 bytes Disabled- Retrain-
CommClk+
ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
LnkSta: Speed 5GT/s, Width x16, TrErr- Train- SlotClk+ DLActive+
BWMgmt+ ABWMgmt-
SltCap: AttnBtn- PwrCtrl- MRL- AttnInd- PwrInd- HotPlug-
Surpise-
Slot # 5, PowerLimit 75.000000; Interlock- NoCompl-
SltCtl: Enable: AttnBtn- PwrFlt- MRL- PresDet- CmdCplt- HPIrq-
LinkChg-
Control: AttnInd Off, PwrInd Off, Power- Interlock-
SltSta: Status: AttnBtn- PowerFlt- MRL- CmdCplt- PresDet+
Interlock-
Changed: MRL- PresDet+ LinkState+
RootCtl: ErrCorrectable+ ErrNon-Fatal+ ErrFatal+ PMEIntEna-
CRSVisible-
RootCap: CRSVisible-
RootSta: PME ReqID 0000, PMEStatus- PMEPending-
Capabilities: [e0] Power Management version 3
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0+,D1-,D2-,D3hot
+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [100] Advanced Error Reporting <?>
Capabilities: [150] Access Controls <?>
Capabilities: [160] Vendor Specific Information <?>
Kernel driver in use: pcieport-driver
Kernel modules: shpchp
00:14.0 PIC: Intel Corporation 5520/5500/X58 I/O Hub System Management
Registers (rev 13) (prog-if 00 [8259])
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort-
<TAbort-
<MAbort- >SERR- <PERR- INTx-
Capabilities: [40] Express (v2) Root Complex Integrated Endpoint, MSI
00
DevCap: MaxPayload 128 bytes, PhantFunc 0, Latency L0s <64ns,
L1 <1us
ExtTag- RBE+ FLReset-
DevCtl: Report errors: Correctable- Non-Fatal- Fatal-
Unsupported-
RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop-
MaxPayload 128 bytes, MaxReadReq 128 bytes
DevSta: CorrErr- UncorrErr- FatalErr- UnsuppReq- AuxPwr-
TransPend-
LnkCap: Port #0, Speed unknown, Width x0, ASPM L0s, Latency L0
unlimited, L1 unlimited
ClockPM- Suprise+ LLActRep+ BwNot+
LnkCtl: ASPM Disabled; Disabled- Retrain- CommClk-
ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
LnkSta: Speed unknown, Width x0, TrErr- Train- SlotClk+
DLActive-
BWMgmt- ABWMgmt-
00:14.1 PIC: Intel Corporation 5520/5500/X58 I/O Hub GPIO and Scratch
Pad Registers (rev 13) (prog-if 00 [8259])
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort-
<TAbort-
<MAbort- >SERR- <PERR- INTx-
Capabilities: [40] Express (v2) Root Complex Integrated Endpoint, MSI
00
DevCap: MaxPayload 128 bytes, PhantFunc 0, Latency L0s <64ns,
L1 <1us
ExtTag- RBE+ FLReset-
DevCtl: Report errors: Correctable- Non-Fatal- Fatal-
Unsupported-
RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop-
MaxPayload 128 bytes, MaxReadReq 128 bytes
DevSta: CorrErr- UncorrErr- FatalErr- UnsuppReq- AuxPwr-
TransPend-
LnkCap: Port #0, Speed unknown, Width x0, ASPM L0s, Latency L0
unlimited, L1 unlimited
ClockPM- Suprise+ LLActRep+ BwNot+
LnkCtl: ASPM Disabled; Disabled- Retrain- CommClk-
ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
LnkSta: Speed unknown, Width x0, TrErr- Train- SlotClk+
DLActive-
BWMgmt- ABWMgmt-
00:14.2 PIC: Intel Corporation 5520/5500/X58 I/O Hub Control Status and
RAS Registers (rev 13) (prog-if 00 [8259])
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort-
<TAbort-
<MAbort- >SERR- <PERR- INTx-
Capabilities: [40] Express (v2) Root Complex Integrated Endpoint, MSI
00
DevCap: MaxPayload 128 bytes, PhantFunc 0, Latency L0s <64ns,
L1 <1us
ExtTag- RBE+ FLReset-
DevCtl: Report errors: Correctable- Non-Fatal- Fatal-
Unsupported-
RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop-
MaxPayload 128 bytes, MaxReadReq 128 bytes
DevSta: CorrErr- UncorrErr- FatalErr- UnsuppReq- AuxPwr-
TransPend-
LnkCap: Port #0, Speed unknown, Width x0, ASPM L0s, Latency L0
unlimited, L1 unlimited
ClockPM- Suprise+ LLActRep+ BwNot+
LnkCtl: ASPM Disabled; Disabled- Retrain- CommClk-
ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
LnkSta: Speed unknown, Width x0, TrErr- Train- SlotClk+
DLActive-
BWMgmt- ABWMgmt-
00:14.3 PIC: Intel Corporation 5520/5500/X58 I/O Hub Throttle Registers
(rev 13) (prog-if 00 [8259])
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort-
<TAbort-
<MAbort- >SERR- <PERR- INTx-
00:16.0 System peripheral: Intel Corporation 5520/5500/X58 Chipset
QuickData Technology Device (rev 13)
Subsystem: Super Micro Computer Inc Device 000b
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort-
<TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 11
Region 0: Memory at fbbfc000 (64-bit, non-prefetchable) [size=16K]
Capabilities: [80] MSI-X: Enable- Mask- TabSize=1
Vector table: BAR=0 offset=00002000
PBA: BAR=0 offset=00003000
Capabilities: [90] Express (v2) Root Complex Integrated Endpoint, MSI
00
DevCap: MaxPayload 128 bytes, PhantFunc 0, Latency L0s <64ns,
L1 <1us
ExtTag- RBE+ FLReset-
DevCtl: Report errors: Correctable- Non-Fatal- Fatal-
Unsupported-
RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop-
MaxPayload 128 bytes, MaxReadReq 128 bytes
DevSta: CorrErr- UncorrErr- FatalErr- UnsuppReq- AuxPwr-
TransPend-
LnkCap: Port #0, Speed unknown, Width x0, ASPM unknown, Latency
L0
<64ns, L1 <1us
ClockPM- Suprise- LLActRep- BwNot-
LnkCtl: ASPM Disabled; Disabled- Retrain- CommClk-
ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
LnkSta: Speed unknown, Width x0, TrErr- Train- SlotClk-
DLActive-
BWMgmt- ABWMgmt-
Capabilities: [e0] Power Management version 3
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA
PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00:16.1 System peripheral: Intel Corporation 5520/5500/X58 Chipset
QuickData Technology Device (rev 13)
Subsystem: Super Micro Computer Inc Device 000b
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort-
<TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Interrupt: pin B routed to IRQ 10
Region 0: Memory at fbbf8000 (64-bit, non-prefetchable) [size=16K]
Capabilities: [80] MSI-X: Enable- Mask- TabSize=1
Vector table: BAR=0 offset=00002000
PBA: BAR=0 offset=00003000
Capabilities: [90] Express (v2) Root Complex Integrated Endpoint, MSI
00
DevCap: MaxPayload 128 bytes, PhantFunc 0, Latency L0s <64ns,
L1 <1us
ExtTag- RBE+ FLReset-
DevCtl: Report errors: Correctable- Non-Fatal- Fatal-
Unsupported-
RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop-
MaxPayload 128 bytes, MaxReadReq 128 bytes
DevSta: CorrErr- UncorrErr- FatalErr- UnsuppReq- AuxPwr-
TransPend-
LnkCap: Port #0, Speed unknown, Width x0, ASPM unknown, Latency
L0
<64ns, L1 <1us
ClockPM- Suprise- LLActRep- BwNot-
LnkCtl: ASPM Disabled; Disabled- Retrain- CommClk-
ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
LnkSta: Speed unknown, Width x0, TrErr- Train- SlotClk-
DLActive-
BWMgmt- ABWMgmt-
Capabilities: [e0] Power Management version 3
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA
PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00:16.2 System peripheral: Intel Corporation 5520/5500/X58 Chipset
QuickData Technology Device (rev 13)
Subsystem: Super Micro Computer Inc Device 000b
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort-
<TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Interrupt: pin C routed to IRQ 14
Region 0: Memory at fbbf4000 (64-bit, non-prefetchable) [size=16K]
Capabilities: [80] MSI-X: Enable- Mask- TabSize=1
Vector table: BAR=0 offset=00002000
PBA: BAR=0 offset=00003000
Capabilities: [90] Express (v2) Root Complex Integrated Endpoint, MSI
00
DevCap: MaxPayload 128 bytes, PhantFunc 0, Latency L0s <64ns,
L1 <1us
ExtTag- RBE+ FLReset-
DevCtl: Report errors: Correctable- Non-Fatal- Fatal-
Unsupported-
RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop-
MaxPayload 128 bytes, MaxReadReq 128 bytes
DevSta: CorrErr- UncorrErr- FatalErr- UnsuppReq- AuxPwr-
TransPend-
LnkCap: Port #0, Speed unknown, Width x0, ASPM unknown, Latency
L0
<64ns, L1 <1us
ClockPM- Suprise- LLActRep- BwNot-
LnkCtl: ASPM Disabled; Disabled- Retrain- CommClk-
ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
LnkSta: Speed unknown, Width x0, TrErr- Train- SlotClk-
DLActive-
BWMgmt- ABWMgmt-
Capabilities: [e0] Power Management version 3
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA
PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00:16.3 System peripheral: Intel Corporation 5520/5500/X58 Chipset
QuickData Technology Device (rev 13)
Subsystem: Super Micro Computer Inc Device 000b
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort-
<TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Interrupt: pin D routed to IRQ 15
Region 0: Memory at fbbf0000 (64-bit, non-prefetchable) [size=16K]
Capabilities: [80] MSI-X: Enable- Mask- TabSize=1
Vector table: BAR=0 offset=00002000
PBA: BAR=0 offset=00003000
Capabilities: [90] Express (v2) Root Complex Integrated Endpoint, MSI
00
DevCap: MaxPayload 128 bytes, PhantFunc 0, Latency L0s <64ns,
L1 <1us
ExtTag- RBE+ FLReset-
DevCtl: Report errors: Correctable- Non-Fatal- Fatal-
Unsupported-
RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop-
MaxPayload 128 bytes, MaxReadReq 128 bytes
DevSta: CorrErr- UncorrErr- FatalErr- UnsuppReq- AuxPwr-
TransPend-
LnkCap: Port #0, Speed unknown, Width x0, ASPM unknown, Latency
L0
<64ns, L1 <1us
ClockPM- Suprise- LLActRep- BwNot-
LnkCtl: ASPM Disabled; Disabled- Retrain- CommClk-
ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
LnkSta: Speed unknown, Width x0, TrErr- Train- SlotClk-
DLActive-
BWMgmt- ABWMgmt-
Capabilities: [e0] Power Management version 3
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA
PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00:16.4 System peripheral: Intel Corporation 5520/5500/X58 Chipset
QuickData Technology Device (rev 13)
Subsystem: Super Micro Computer Inc Device 000b
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort-
<TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 11
Region 0: Memory at fbbec000 (64-bit, non-prefetchable) [size=16K]
Capabilities: [80] MSI-X: Enable- Mask- TabSize=1
Vector table: BAR=0 offset=00002000
PBA: BAR=0 offset=00003000
Capabilities: [90] Express (v2) Root Complex Integrated Endpoint, MSI
00
DevCap: MaxPayload 128 bytes, PhantFunc 0, Latency L0s <64ns,
L1 <1us
ExtTag- RBE+ FLReset-
DevCtl: Report errors: Correctable- Non-Fatal- Fatal-
Unsupported-
RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop-
MaxPayload 128 bytes, MaxReadReq 128 bytes
DevSta: CorrErr- UncorrErr- FatalErr- UnsuppReq- AuxPwr-
TransPend-
LnkCap: Port #0, Speed unknown, Width x0, ASPM unknown, Latency
L0
<64ns, L1 <1us
ClockPM- Suprise- LLActRep- BwNot-
LnkCtl: ASPM Disabled; Disabled- Retrain- CommClk-
ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
LnkSta: Speed unknown, Width x0, TrErr- Train- SlotClk-
DLActive-
BWMgmt- ABWMgmt-
Capabilities: [e0] Power Management version 3
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA
PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00:16.5 System peripheral: Intel Corporation 5520/5500/X58 Chipset
QuickData Technology Device (rev 13)
Subsystem: Super Micro Computer Inc Device 000b
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort-
<TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Interrupt: pin B routed to IRQ 10
Region 0: Memory at fbbe8000 (64-bit, non-prefetchable) [size=16K]
Capabilities: [80] MSI-X: Enable- Mask- TabSize=1
Vector table: BAR=0 offset=00002000
PBA: BAR=0 offset=00003000
Capabilities: [90] Express (v2) Root Complex Integrated Endpoint, MSI
00
DevCap: MaxPayload 128 bytes, PhantFunc 0, Latency L0s <64ns,
L1 <1us
ExtTag- RBE+ FLReset-
DevCtl: Report errors: Correctable- Non-Fatal- Fatal-
Unsupported-
RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop-
MaxPayload 128 bytes, MaxReadReq 128 bytes
DevSta: CorrErr- UncorrErr- FatalErr- UnsuppReq- AuxPwr-
TransPend-
LnkCap: Port #0, Speed unknown, Width x0, ASPM unknown, Latency
L0
<64ns, L1 <1us
ClockPM- Suprise- LLActRep- BwNot-
LnkCtl: ASPM Disabled; Disabled- Retrain- CommClk-
ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
LnkSta: Speed unknown, Width x0, TrErr- Train- SlotClk-
DLActive-
BWMgmt- ABWMgmt-
Capabilities: [e0] Power Management version 3
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA
PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00:16.6 System peripheral: Intel Corporation 5520/5500/X58 Chipset
QuickData Technology Device (rev 13)
Subsystem: Super Micro Computer Inc Device 000b
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort-
<TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Interrupt: pin C routed to IRQ 14
Region 0: Memory at fbbe4000 (64-bit, non-prefetchable) [size=16K]
Capabilities: [80] MSI-X: Enable- Mask- TabSize=1
Vector table: BAR=0 offset=00002000
PBA: BAR=0 offset=00003000
Capabilities: [90] Express (v2) Root Complex Integrated Endpoint, MSI
00
DevCap: MaxPayload 128 bytes, PhantFunc 0, Latency L0s <64ns,
L1 <1us
ExtTag- RBE+ FLReset-
DevCtl: Report errors: Correctable- Non-Fatal- Fatal-
Unsupported-
RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop-
MaxPayload 128 bytes, MaxReadReq 128 bytes
DevSta: CorrErr- UncorrErr- FatalErr- UnsuppReq- AuxPwr-
TransPend-
LnkCap: Port #0, Speed unknown, Width x0, ASPM unknown, Latency
L0
<64ns, L1 <1us
ClockPM- Suprise- LLActRep- BwNot-
LnkCtl: ASPM Disabled; Disabled- Retrain- CommClk-
ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
LnkSta: Speed unknown, Width x0, TrErr- Train- SlotClk-
DLActive-
BWMgmt- ABWMgmt-
Capabilities: [e0] Power Management version 3
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA
PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00:16.7 System peripheral: Intel Corporation 5520/5500/X58 Chipset
QuickData Technology Device (rev 13)
Subsystem: Super Micro Computer Inc Device 000b
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort-
<TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Interrupt: pin D routed to IRQ 15
Region 0: Memory at fbbe0000 (64-bit, non-prefetchable) [size=16K]
Capabilities: [80] MSI-X: Enable- Mask- TabSize=1
Vector table: BAR=0 offset=00002000
PBA: BAR=0 offset=00003000
Capabilities: [90] Express (v2) Root Complex Integrated Endpoint, MSI
00
DevCap: MaxPayload 128 bytes, PhantFunc 0, Latency L0s <64ns,
L1 <1us
ExtTag- RBE+ FLReset-
DevCtl: Report errors: Correctable- Non-Fatal- Fatal-
Unsupported-
RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop-
MaxPayload 128 bytes, MaxReadReq 128 bytes
DevSta: CorrErr- UncorrErr- FatalErr- UnsuppReq- AuxPwr-
TransPend-
LnkCap: Port #0, Speed unknown, Width x0, ASPM unknown, Latency
L0
<64ns, L1 <1us
ClockPM- Suprise- LLActRep- BwNot-
LnkCtl: ASPM Disabled; Disabled- Retrain- CommClk-
ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
LnkSta: Speed unknown, Width x0, TrErr- Train- SlotClk-
DLActive-
BWMgmt- ABWMgmt-
Capabilities: [e0] Power Management version 3
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA
PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00:1a.0 USB Controller: Intel Corporation 82801JI (ICH10 Family) USB
UHCI Controller #4 (prog-if 00 [UHCI])
Subsystem: Super Micro Computer Inc Device 000b
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin A routed to IRQ 16
Region 4: I/O ports at ac00 [size=32]
Capabilities: [50] PCIe advanced features <?>
Kernel driver in use: uhci_hcd
Kernel modules: uhci-hcd
00:1a.1 USB Controller: Intel Corporation 82801JI (ICH10 Family) USB
UHCI Controller #5 (prog-if 00 [UHCI])
Subsystem: Super Micro Computer Inc Device 000b
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin B routed to IRQ 21
Region 4: I/O ports at a880 [size=32]
Capabilities: [50] PCIe advanced features <?>
Kernel driver in use: uhci_hcd
Kernel modules: uhci-hcd
00:1a.2 USB Controller: Intel Corporation 82801JI (ICH10 Family) USB
UHCI Controller #6 (prog-if 00 [UHCI])
Subsystem: Super Micro Computer Inc Device 000b
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin D routed to IRQ 19
Region 4: I/O ports at a800 [size=32]
Capabilities: [50] PCIe advanced features <?>
Kernel driver in use: uhci_hcd
Kernel modules: uhci-hcd
00:1a.7 USB Controller: Intel Corporation 82801JI (ICH10 Family) USB2
EHCI Controller #2 (prog-if 20 [EHCI])
Subsystem: Super Micro Computer Inc Device 000b
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin C routed to IRQ 18
Region 0: Memory at fbbde000 (32-bit, non-prefetchable) [size=1K]
Capabilities: [50] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=375mA
PME(D0+,D1-,D2-,D3hot
+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [58] Debug port: BAR=1 offset=00a0
Capabilities: [98] PCIe advanced features <?>
Kernel driver in use: ehci_hcd
Kernel modules: ehci-hcd
00:1b.0 Audio device: Intel Corporation 82801JI (ICH10 Family) HD Audio
Controller
Subsystem: Super Micro Computer Inc Device 000b
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort-
<TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 22
Region 0: Memory at fbbd8000 (64-bit, non-prefetchable) [size=16K]
Capabilities: [50] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=55mA
PME(D0+,D1-,D2-,D3hot
+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [60] Message Signalled Interrupts: Mask- 64bit+ Queue=0/0
Enable-
Address: 0000000000000000 Data: 0000
Capabilities: [70] Express (v1) Root Complex Integrated Endpoint, MSI
00
DevCap: MaxPayload 128 bytes, PhantFunc 0, Latency L0s <64ns,
L1 <1us
ExtTag- RBE- FLReset+
DevCtl: Report errors: Correctable- Non-Fatal- Fatal-
Unsupported-
RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop+
MaxPayload 128 bytes, MaxReadReq 128 bytes
DevSta: CorrErr- UncorrErr- FatalErr- UnsuppReq- AuxPwr+
TransPend-
LnkCap: Port #0, Speed unknown, Width x0, ASPM unknown, Latency
L0
<64ns, L1 <1us
ClockPM- Suprise- LLActRep- BwNot-
LnkCtl: ASPM Disabled; Disabled- Retrain- CommClk-
ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
LnkSta: Speed unknown, Width x0, TrErr- Train- SlotClk-
DLActive-
BWMgmt- ABWMgmt-
Capabilities: [100] Virtual Channel <?>
Capabilities: [130] Root Complex Link <?>
Kernel driver in use: HDA Intel
Kernel modules: snd-hda-intel
00:1c.0 PCI bridge: Intel Corporation 82801JI (ICH10 Family) PCI Express
Root Port 1 (prog-if 00 [Normal decode])
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR+ FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort-
<TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Bus: primary=00, secondary=04, subordinate=06, sec-latency=0
I/O behind bridge: 0000f000-00000fff
Memory behind bridge: fbc00000-fbcfffff
Prefetchable memory behind bridge: 00000000f2f00000-00000000f2ffffff
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort-
<TAbort-
<MAbort+ <SERR- <PERR-
BridgeCtl: Parity- SERR+ NoISA- VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: [40] Express (v1) Root Port (Slot+), MSI 00
DevCap: MaxPayload 128 bytes, PhantFunc 0, Latency L0s <64ns,
L1 <1us
ExtTag- RBE+ FLReset-
DevCtl: Report errors: Correctable- Non-Fatal- Fatal-
Unsupported-
RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop-
MaxPayload 128 bytes, MaxReadReq 128 bytes
DevSta: CorrErr+ UncorrErr- FatalErr- UnsuppReq- AuxPwr+
TransPend-
LnkCap: Port #1, Speed 2.5GT/s, Width x4, ASPM L0s L1, Latency
L0
<256ns, L1 <4us
ClockPM- Suprise- LLActRep+ BwNot-
LnkCtl: ASPM L0s L1 Enabled; RCB 64 bytes Disabled- Retrain-
CommClk+
ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
LnkSta: Speed 2.5GT/s, Width x4, TrErr- Train- SlotClk+
DLActive+
BWMgmt- ABWMgmt-
SltCap: AttnBtn- PwrCtrl- MRL- AttnInd- PwrInd- HotPlug+
Surpise+
Slot # 0, PowerLimit 25.000000; Interlock- NoCompl-
SltCtl: Enable: AttnBtn- PwrFlt- MRL- PresDet- CmdCplt- HPIrq-
LinkChg-
Control: AttnInd Unknown, PwrInd Unknown, Power-
Interlock-
SltSta: Status: AttnBtn- PowerFlt- MRL- CmdCplt- PresDet+
Interlock-
Changed: MRL- PresDet+ LinkState+
RootCtl: ErrCorrectable- ErrNon-Fatal- ErrFatal- PMEIntEna-
CRSVisible-
RootCap: CRSVisible-
RootSta: PME ReqID 0000, PMEStatus- PMEPending-
Capabilities: [80] Message Signalled Interrupts: Mask- 64bit- Queue=0/0
Enable+
Address: fee00000 Data: 40c8
Capabilities: [90] Subsystem: Super Micro Computer Inc Device 000b
Capabilities: [a0] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0+,D1-,D2-,D3hot
+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [100] Virtual Channel <?>
Capabilities: [180] Root Complex Link <?>
Kernel driver in use: pcieport-driver
Kernel modules: shpchp
00:1c.4 PCI bridge: Intel Corporation 82801JI (ICH10 Family) PCI Express
Root Port 5 (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR+ FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort-
<TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Bus: primary=00, secondary=07, subordinate=07, sec-latency=0
I/O behind bridge: 0000d000-0000dfff
Memory behind bridge: fbd00000-fbdfffff
Prefetchable memory behind bridge: 00000000fff00000-00000000000fffff
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort-
<TAbort-
<MAbort- <SERR- <PERR-
BridgeCtl: Parity- SERR+ NoISA- VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: [40] Express (v1) Root Port (Slot+), MSI 00
DevCap: MaxPayload 128 bytes, PhantFunc 0, Latency L0s <64ns,
L1 <1us
ExtTag- RBE+ FLReset-
DevCtl: Report errors: Correctable- Non-Fatal- Fatal-
Unsupported-
RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop-
MaxPayload 128 bytes, MaxReadReq 128 bytes
DevSta: CorrErr+ UncorrErr- FatalErr- UnsuppReq- AuxPwr+
TransPend-
LnkCap: Port #5, Speed 2.5GT/s, Width x1, ASPM L0s L1, Latency
L0
<256ns, L1 <4us
ClockPM- Suprise- LLActRep+ BwNot-
LnkCtl: ASPM L0s L1 Enabled; RCB 64 bytes Disabled- Retrain-
CommClk+
ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
LnkSta: Speed 2.5GT/s, Width x1, TrErr- Train- SlotClk+
DLActive+
BWMgmt- ABWMgmt-
SltCap: AttnBtn- PwrCtrl- MRL- AttnInd- PwrInd- HotPlug+
Surpise+
Slot # 0, PowerLimit 10.000000; Interlock- NoCompl-
SltCtl: Enable: AttnBtn- PwrFlt- MRL- PresDet- CmdCplt- HPIrq-
LinkChg-
Control: AttnInd Unknown, PwrInd Unknown, Power-
Interlock-
SltSta: Status: AttnBtn- PowerFlt- MRL- CmdCplt- PresDet+
Interlock-
Changed: MRL- PresDet+ LinkState+
RootCtl: ErrCorrectable- ErrNon-Fatal- ErrFatal- PMEIntEna-
CRSVisible-
RootCap: CRSVisible-
RootSta: PME ReqID 0000, PMEStatus- PMEPending-
Capabilities: [80] Message Signalled Interrupts: Mask- 64bit- Queue=0/0
Enable+
Address: fee00000 Data: 40d0
Capabilities: [90] Subsystem: Super Micro Computer Inc Device 000b
Capabilities: [a0] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0+,D1-,D2-,D3hot
+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [100] Virtual Channel <?>
Capabilities: [180] Root Complex Link <?>
Kernel driver in use: pcieport-driver
Kernel modules: shpchp
00:1c.5 PCI bridge: Intel Corporation 82801JI (ICH10 Family) PCI Express
Root Port 6 (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR+ FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort-
<TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Bus: primary=00, secondary=08, subordinate=08, sec-latency=0
I/O behind bridge: 0000e000-0000efff
Memory behind bridge: fbe00000-fbefffff
Prefetchable memory behind bridge: 00000000fff00000-00000000000fffff
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort-
<TAbort-
<MAbort- <SERR- <PERR-
BridgeCtl: Parity- SERR+ NoISA- VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: [40] Express (v1) Root Port (Slot+), MSI 00
DevCap: MaxPayload 128 bytes, PhantFunc 0, Latency L0s <64ns,
L1 <1us
ExtTag- RBE+ FLReset-
DevCtl: Report errors: Correctable- Non-Fatal- Fatal-
Unsupported-
RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop-
MaxPayload 128 bytes, MaxReadReq 128 bytes
DevSta: CorrErr+ UncorrErr- FatalErr- UnsuppReq- AuxPwr+
TransPend-
LnkCap: Port #6, Speed 2.5GT/s, Width x1, ASPM L0s L1, Latency
L0
<256ns, L1 <4us
ClockPM- Suprise- LLActRep+ BwNot-
LnkCtl: ASPM L0s L1 Enabled; RCB 64 bytes Disabled- Retrain-
CommClk+
ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
LnkSta: Speed 2.5GT/s, Width x1, TrErr- Train- SlotClk+
DLActive+
BWMgmt- ABWMgmt-
SltCap: AttnBtn- PwrCtrl- MRL- AttnInd- PwrInd- HotPlug+
Surpise+
Slot # 0, PowerLimit 10.000000; Interlock- NoCompl-
SltCtl: Enable: AttnBtn- PwrFlt- MRL- PresDet- CmdCplt- HPIrq-
LinkChg-
Control: AttnInd Unknown, PwrInd Unknown, Power-
Interlock-
SltSta: Status: AttnBtn- PowerFlt- MRL- CmdCplt- PresDet+
Interlock-
Changed: MRL- PresDet+ LinkState+
RootCtl: ErrCorrectable- ErrNon-Fatal- ErrFatal- PMEIntEna-
CRSVisible-
RootCap: CRSVisible-
RootSta: PME ReqID 0000, PMEStatus- PMEPending-
Capabilities: [80] Message Signalled Interrupts: Mask- 64bit- Queue=0/0
Enable+
Address: fee00000 Data: 40d8
Capabilities: [90] Subsystem: Super Micro Computer Inc Device 000b
Capabilities: [a0] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0+,D1-,D2-,D3hot
+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [100] Virtual Channel <?>
Capabilities: [180] Root Complex Link <?>
Kernel driver in use: pcieport-driver
Kernel modules: shpchp
00:1d.0 USB Controller: Intel Corporation 82801JI (ICH10 Family) USB
UHCI Controller #1 (prog-if 00 [UHCI])
Subsystem: Super Micro Computer Inc Device 000b
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin A routed to IRQ 23
Region 4: I/O ports at a480 [size=32]
Capabilities: [50] PCIe advanced features <?>
Kernel driver in use: uhci_hcd
Kernel modules: uhci-hcd
00:1d.1 USB Controller: Intel Corporation 82801JI (ICH10 Family) USB
UHCI Controller #2 (prog-if 00 [UHCI])
Subsystem: Super Micro Computer Inc Device 000b
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin B routed to IRQ 19
Region 4: I/O ports at a400 [size=32]
Capabilities: [50] PCIe advanced features <?>
Kernel driver in use: uhci_hcd
Kernel modules: uhci-hcd
00:1d.2 USB Controller: Intel Corporation 82801JI (ICH10 Family) USB
UHCI Controller #3 (prog-if 00 [UHCI])
Subsystem: Super Micro Computer Inc Device 000b
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin C routed to IRQ 18
Region 4: I/O ports at a080 [size=32]
Capabilities: [50] PCIe advanced features <?>
Kernel driver in use: uhci_hcd
Kernel modules: uhci-hcd
00:1d.7 USB Controller: Intel Corporation 82801JI (ICH10 Family) USB2
EHCI Controller #1 (prog-if 20 [EHCI])
Subsystem: Super Micro Computer Inc Device 000b
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin A routed to IRQ 23
Region 0: Memory at fbbdc000 (32-bit, non-prefetchable) [size=1K]
Capabilities: [50] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=375mA
PME(D0+,D1-,D2-,D3hot
+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [58] Debug port: BAR=1 offset=00a0
Capabilities: [98] PCIe advanced features <?>
Kernel driver in use: ehci_hcd
Kernel modules: ehci-hcd
00:1e.0 PCI bridge: Intel Corporation 82801 PCI Bridge (rev 90) (prog-if
01 [Subtractive decode])
Control: I/O- Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR+ FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort-
<TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0
Bus: primary=00, secondary=09, subordinate=09, sec-latency=32
I/O behind bridge: 0000f000-00000fff
Memory behind bridge: fff00000-000fffff
Prefetchable memory behind bridge: 00000000fff00000-00000000000fffff
Secondary status: 66MHz- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort+ <SERR- <PERR-
BridgeCtl: Parity- SERR+ NoISA- VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: [50] Subsystem: Super Micro Computer Inc Device 000b
00:1f.0 ISA bridge: Intel Corporation 82801JIR (ICH10R) LPC Interface
Controller
Subsystem: Super Micro Computer Inc Device 000b
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Capabilities: [e0] Vendor Specific Information <?>
Kernel modules: iTCO_wdt
00:1f.2 SATA controller: Intel Corporation 82801JI (ICH10 Family) SATA
AHCI Controller (prog-if 01 [AHCI 1.0])
Subsystem: Super Micro Computer Inc Device 000b
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin B routed to IRQ 758
Region 0: I/O ports at a000 [size=8]
Region 1: I/O ports at 9c00 [size=4]
Region 2: I/O ports at 9880 [size=8]
Region 3: I/O ports at 9800 [size=4]
Region 4: I/O ports at 9480 [size=32]
Region 5: Memory at fbbd6000 (32-bit, non-prefetchable) [size=2K]
Capabilities: [80] Message Signalled Interrupts: Mask- 64bit- Queue=0/4
Enable+
Address: fee14000 Data: 4089
Capabilities: [70] Power Management version 3
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot
+,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [a8] SATA HBA <?>
Capabilities: [b0] PCIe advanced features <?>
Kernel driver in use: ahci
Kernel modules: ahci
00:1f.3 SMBus: Intel Corporation 82801JI (ICH10 Family) SMBus Controller
Subsystem: Super Micro Computer Inc Device 000b
Control: I/O+ Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Interrupt: pin C routed to IRQ 18
Region 0: Memory at fbbd4000 (64-bit, non-prefetchable) [size=256]
Region 4: I/O ports at 0400 [size=32]
Kernel driver in use: i801_smbus
Kernel modules: i2c-i801
01:00.0 VGA compatible controller: nVidia Corporation G86 [Quadro NVS
290] (rev a1) (prog-if 00 [VGA controller])
Subsystem: nVidia Corporation Device 0492
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr+
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort-
<TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin A routed to IRQ 16
Region 0: Memory at f6000000 (32-bit, non-prefetchable) [size=16M]
Region 1: Memory at c0000000 (64-bit, prefetchable) [size=256M]
Region 3: Memory at f4000000 (64-bit, non-prefetchable) [size=32M]
Region 5: I/O ports at bc00 [disabled] [size=128]
[virtual] Expansion ROM at f3fe0000 [disabled] [size=128K]
Capabilities: [60] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA
PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [68] Message Signalled Interrupts: Mask- 64bit+ Queue=0/0
Enable-
Address: 0000000000000000 Data: 0000
Capabilities: [78] Express (v1) Endpoint, MSI 00
DevCap: MaxPayload 128 bytes, PhantFunc 0, Latency L0s
<512ns, L1 <4us
ExtTag+ AttnBtn- AttnInd- PwrInd- RBE+ FLReset-
DevCtl: Report errors: Correctable- Non-Fatal- Fatal-
Unsupported-
RlxdOrd+ ExtTag+ PhantFunc- AuxPwr- NoSnoop+
MaxPayload 128 bytes, MaxReadReq 512 bytes
DevSta: CorrErr- UncorrErr- FatalErr- UnsuppReq- AuxPwr-
TransPend-
LnkCap: Port #0, Speed 2.5GT/s, Width x16, ASPM L0s L1, Latency
L0
<512ns, L1 <4us
ClockPM- Suprise- LLActRep- BwNot-
LnkCtl: ASPM L0s Enabled; RCB 128 bytes Disabled- Retrain-
CommClk+
ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
LnkSta: Speed 2.5GT/s, Width x4, TrErr- Train- SlotClk+
DLActive-
BWMgmt- ABWMgmt-
Capabilities: [100] Virtual Channel <?>
Capabilities: [128] Power Budgeting <?>
Capabilities: [600] Vendor Specific Information <?>
Kernel driver in use: nvidia
Kernel modules: nvidia, nvidiafb
03:00.0 VGA compatible controller: nVidia Corporation Device 06fd (rev
a1) (prog-if 00 [VGA controller])
Subsystem: nVidia Corporation Device 062e
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr+
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort-
<TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin A routed to IRQ 16
Region 0: Memory at fa000000 (32-bit, non-prefetchable) [size=16M]
Region 1: Memory at d0000000 (64-bit, prefetchable) [size=256M]
Region 3: Memory at f8000000 (64-bit, non-prefetchable) [size=32M]
Region 5: I/O ports at cc00 [size=128]
[virtual] Expansion ROM at f7fe0000 [disabled] [size=128K]
Capabilities: [60] Power Management version 3
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA
PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [68] Message Signalled Interrupts: Mask- 64bit+ Queue=0/0
Enable-
Address: 0000000000000000 Data: 0000
Capabilities: [78] Express (v2) Endpoint, MSI 00
DevCap: MaxPayload 128 bytes, PhantFunc 0, Latency L0s
<512ns, L1 <4us
ExtTag+ AttnBtn- AttnInd- PwrInd- RBE+ FLReset-
DevCtl: Report errors: Correctable- Non-Fatal- Fatal-
Unsupported-
RlxdOrd+ ExtTag+ PhantFunc- AuxPwr- NoSnoop+
MaxPayload 128 bytes, MaxReadReq 512 bytes
DevSta: CorrErr+ UncorrErr- FatalErr- UnsuppReq- AuxPwr-
TransPend+
LnkCap: Port #0, Speed 5GT/s, Width x16, ASPM L0s L1, Latency L0
<256ns, L1 <1us
ClockPM- Suprise- LLActRep- BwNot-
LnkCtl: ASPM L0s Enabled; RCB 128 bytes Disabled- Retrain-
CommClk+
ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
LnkSta: Speed 5GT/s, Width x16, TrErr- Train- SlotClk+ DLActive-
BWMgmt- ABWMgmt-
Capabilities: [100] Virtual Channel <?>
Capabilities: [128] Power Budgeting <?>
Capabilities: [600] Vendor Specific Information <?>
Kernel driver in use: nvidia
Kernel modules: nvidia, nvidiafb
04:00.0 PCI bridge: Intel Corporation 80333 Segment-A PCI Express-to-PCI
Express Bridge (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR+ FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort-
<TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Bus: primary=04, secondary=05, subordinate=05, sec-latency=64
I/O behind bridge: 0000f000-00000fff
Memory behind bridge: fbc00000-fbcfffff
Prefetchable memory behind bridge: 00000000f2f00000-00000000f2ffffff
Secondary status: 66MHz+ FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort+ <SERR- <PERR-
BridgeCtl: Parity- SERR+ NoISA- VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: [44] Express (v1) PCI/PCI-X Bridge, MSI 00
DevCap: MaxPayload 256 bytes, PhantFunc 0, Latency L0s <64ns,
L1 <1us
ExtTag- AttnBtn- AttnInd- PwrInd- RBE- FLReset-
DevCtl: Report errors: Correctable- Non-Fatal- Fatal-
Unsupported-
RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop- BrConfRtry+
MaxPayload 128 bytes, MaxReadReq 512 bytes
DevSta: CorrErr+ UncorrErr+ FatalErr- UnsuppReq+ AuxPwr-
TransPend-
LnkCap: Port #0, Speed 2.5GT/s, Width x8, ASPM L0s, Latency L0
unlimited, L1 unlimited
ClockPM- Suprise- LLActRep- BwNot-
LnkCtl: ASPM L0s L1 Enabled; Disabled- Retrain- CommClk-
ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
LnkSta: Speed 2.5GT/s, Width x4, TrErr- Train- SlotClk-
DLActive-
BWMgmt- ABWMgmt-
Capabilities: [5c] Message Signalled Interrupts: Mask- 64bit+ Queue=0/0
Enable-
Address: 0000000000000000 Data: 0000
Capabilities: [6c] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0+,D1-,D2-,D3hot
+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [d8] PCI-X bridge device
Secondary Status: 64bit+ 133MHz+ SCD- USC- SCO- SRD- Freq=133MHz
Status: Dev=04:00.0 64bit- 133MHz- SCD- USC- SCO- SRD-
Upstream: Capacity=65535 CommitmentLimit=65535
Downstream: Capacity=65535 CommitmentLimit=65535
Capabilities: [100] Advanced Error Reporting <?>
Capabilities: [300] Power Budgeting <?>
Kernel modules: shpchp
04:00.2 PCI bridge: Intel Corporation 80333 Segment-B PCI Express-to-PCI
Express Bridge (prog-if 00 [Normal decode])
Control: I/O- Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR+ FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort-
<TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Bus: primary=04, secondary=06, subordinate=06, sec-latency=64
I/O behind bridge: 0000f000-00000fff
Memory behind bridge: fff00000-000fffff
Prefetchable memory behind bridge: 00000000fff00000-00000000000fffff
Secondary status: 66MHz+ FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort+ <SERR- <PERR-
BridgeCtl: Parity- SERR+ NoISA- VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: [44] Express (v1) PCI/PCI-X Bridge, MSI 00
DevCap: MaxPayload 256 bytes, PhantFunc 0, Latency L0s <64ns,
L1 <1us
ExtTag- AttnBtn- AttnInd- PwrInd- RBE- FLReset-
DevCtl: Report errors: Correctable- Non-Fatal- Fatal-
Unsupported-
RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop- BrConfRtry-
MaxPayload 128 bytes, MaxReadReq 512 bytes
DevSta: CorrErr+ UncorrErr+ FatalErr- UnsuppReq+ AuxPwr-
TransPend-
LnkCap: Port #0, Speed 2.5GT/s, Width x8, ASPM L0s, Latency L0
unlimited, L1 unlimited
ClockPM- Suprise- LLActRep- BwNot-
LnkCtl: ASPM L0s L1 Enabled; Disabled- Retrain- CommClk-
ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
LnkSta: Speed 2.5GT/s, Width x4, TrErr- Train- SlotClk-
DLActive-
BWMgmt- ABWMgmt-
Capabilities: [5c] Message Signalled Interrupts: Mask- 64bit+ Queue=0/0
Enable-
Address: 0000000000000000 Data: 0000
Capabilities: [6c] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0+,D1-,D2-,D3hot
+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [d8] PCI-X bridge device
Secondary Status: 64bit+ 133MHz+ SCD- USC- SCO- SRD- Freq=133MHz
Status: Dev=04:00.2 64bit- 133MHz- SCD- USC- SCO- SRD-
Upstream: Capacity=65535 CommitmentLimit=65535
Downstream: Capacity=65535 CommitmentLimit=65535
Capabilities: [100] Advanced Error Reporting <?>
Capabilities: [300] Power Budgeting <?>
Kernel modules: shpchp
05:0e.0 RAID bus controller: Dell PowerEdge Expandable RAID controller 5
Subsystem: Dell PERC 5/i Integrated RAID Controller
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr-
Stepping+ SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 64 (32000ns min), Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 18
Region 0: Memory at f2ff0000 (32-bit, prefetchable) [size=64K]
Region 2: Memory at fbce0000 (32-bit, non-prefetchable) [size=128K]
Expansion ROM at fbcd0000 [disabled] [size=32K]
Capabilities: [c0] Power Management version 2
Flags: PMEClk- DSI- D1+ D2- AuxCurrent=0mA
PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [d0] Message Signalled Interrupts: Mask- 64bit+ Queue=0/1
Enable-
Address: 0000000000000000 Data: 0000
Capabilities: [e0] PCI-X non-bridge device
Command: DPERE- ERO- RBC=512 OST=4
Status: Dev=05:0e.0 64bit+ 133MHz+ SCD- USC- DC=bridge
DMMRBC=1024
DMOST=4 DMCRS=16 RSCEM- 266MHz- 533MHz-
Kernel driver in use: megaraid_sas
Kernel modules: megaraid_sas
07:00.0 Ethernet controller: Intel Corporation 82574L Gigabit Network
Connection
Subsystem: Super Micro Computer Inc Device 10d3
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort-
<TAbort-
<MAbort- >SERR- <PERR- INTx+
Latency: 0, Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 16
Region 0: Memory at fbde0000 (32-bit, non-prefetchable) [size=128K]
Region 2: I/O ports at dc00 [size=32]
Region 3: Memory at fbddc000 (32-bit, non-prefetchable) [size=16K]
Capabilities: [c8] Power Management version 2
Flags: PMEClk- DSI+ D1- D2- AuxCurrent=0mA PME(D0+,D1-,D2-,D3hot
+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=1 PME-
Capabilities: [d0] Message Signalled Interrupts: Mask- 64bit+ Queue=0/0
Enable-
Address: 0000000000000000 Data: 0000
Capabilities: [e0] Express (v1) Endpoint, MSI 00
DevCap: MaxPayload 256 bytes, PhantFunc 0, Latency L0s
<512ns, L1
<64us
ExtTag- AttnBtn- AttnInd- PwrInd- RBE+ FLReset-
DevCtl: Report errors: Correctable- Non-Fatal- Fatal-
Unsupported-
RlxdOrd+ ExtTag- PhantFunc- AuxPwr- NoSnoop+
MaxPayload 128 bytes, MaxReadReq 512 bytes
DevSta: CorrErr+ UncorrErr- FatalErr- UnsuppReq+ AuxPwr+
TransPend-
LnkCap: Port #0, Speed 2.5GT/s, Width x1, ASPM L0s L1, Latency
L0
<128ns, L1 <64us
ClockPM- Suprise- LLActRep- BwNot-
LnkCtl: ASPM L0s Enabled; RCB 64 bytes Disabled- Retrain-
CommClk+
ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
LnkSta: Speed 2.5GT/s, Width x1, TrErr- Train- SlotClk+
DLActive-
BWMgmt- ABWMgmt-
Capabilities: [a0] MSI-X: Enable+ Mask- TabSize=5
Vector table: BAR=3 offset=00000000
PBA: BAR=3 offset=00002000
Capabilities: [100] Advanced Error Reporting <?>
Kernel driver in use: e1000e
Kernel modules: e1000e
08:00.0 Ethernet controller: Intel Corporation 82574L Gigabit Network
Connection
Subsystem: Super Micro Computer Inc Device 10d3
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort-
<TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 17
Region 0: Memory at fbee0000 (32-bit, non-prefetchable) [size=128K]
Region 2: I/O ports at ec00 [size=32]
Region 3: Memory at fbedc000 (32-bit, non-prefetchable) [size=16K]
Capabilities: [c8] Power Management version 2
Flags: PMEClk- DSI+ D1- D2- AuxCurrent=0mA PME(D0+,D1-,D2-,D3hot
+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=1 PME-
Capabilities: [d0] Message Signalled Interrupts: Mask- 64bit+ Queue=0/0
Enable-
Address: 0000000000000000 Data: 0000
Capabilities: [e0] Express (v1) Endpoint, MSI 00
DevCap: MaxPayload 256 bytes, PhantFunc 0, Latency L0s
<512ns, L1
<64us
ExtTag- AttnBtn- AttnInd- PwrInd- RBE+ FLReset-
DevCtl: Report errors: Correctable- Non-Fatal- Fatal-
Unsupported-
RlxdOrd+ ExtTag- PhantFunc- AuxPwr- NoSnoop+
MaxPayload 128 bytes, MaxReadReq 512 bytes
DevSta: CorrErr+ UncorrErr- FatalErr- UnsuppReq+ AuxPwr+
TransPend-
LnkCap: Port #0, Speed 2.5GT/s, Width x1, ASPM L0s L1, Latency
L0
<128ns, L1 <64us
ClockPM- Suprise- LLActRep- BwNot-
LnkCtl: ASPM L0s Enabled; RCB 64 bytes Disabled- Retrain-
CommClk+
ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
LnkSta: Speed 2.5GT/s, Width x1, TrErr- Train- SlotClk+
DLActive-
BWMgmt- ABWMgmt-
Capabilities: [a0] MSI-X: Enable+ Mask- TabSize=5
Vector table: BAR=3 offset=00000000
PBA: BAR=3 offset=00002000
Capabilities: [100] Advanced Error Reporting <?>
Kernel driver in use: e1000e
Kernel modules: e1000e
On Wed, 2010-06-02 at 09:23 +0800, Weidong Han wrote:>
>
>
>
> This PCI-x card is not suitable for assignment. It contains an
> invisible
> device 05:08.0 (lspci cannot show it), but this invisible device
> won''t
> be mapped by VT-d because VT-d engine doesn''t know this device, so
> you
> can see the DMAR faults on it. One workaround is to hard code to map
> 05:08.0 when assign 05:0e.0. BTW, PCIe LSI card don''t have this
> problem.
>
_______________________________________________
Xen-devel mailing list
Xen-devel@lists.xensource.com
http://lists.xensource.com/xen-devel
Pasi Kärkkäinen
2010-Jun-02 06:26 UTC
Re: [Xen-devel] iommuu/vt-d issues with LSI MegaSAS (PERC5i)
On Wed, Jun 02, 2010 at 09:23:37AM +0800, Weidong Han wrote:> This PCI-x card is not suitable for assignment. It contains an invisible > device 05:08.0 (lspci cannot show it), but this invisible device won''t > be mapped by VT-d because VT-d engine doesn''t know this device, so you > can see the DMAR faults on it. One workaround is to hard code to map > 05:08.0 when assign 05:0e.0. BTW, PCIe LSI card don''t have this problem. >Note that this problem happens when booting up dom0.. -- Pasi> Regards, > Weidong > > M. Nunberg wrote: >> I''ve been trying to get VT-D working wiht xen for quite some time, since >> 3.4.2, and I''ve always had issues with my RAID controller not working >> properly when iommu is not disabled in Xen: >> >> lspci outpuut for the card: >> 05:0e.0 RAID bus controller: Dell PowerEdge Expandable RAID controller 5 >> Subsystem: Dell PERC 5/i Integrated RAID Controller >> Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- >> Stepping+ SERR- FastB2B- DisINTx- >> Status: Cap+ 66MHz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- >> <TAbort- <MAbort- >SERR- <PERR- INTx- >> Latency: 64 (32000ns min), Cache Line Size: 64 bytes >> Interrupt: pin A routed to IRQ 18 >> Region 0: Memory at f2ff0000 (32-bit, prefetchable) [size=64K] >> Region 2: Memory at fbce0000 (32-bit, non-prefetchable) [size=128K] >> Expansion ROM at fbcd0000 [disabled] [size=32K] >> Capabilities: [c0] Power Management version 2 >> Flags: PMEClk- DSI- D1+ D2- AuxCurrent=0mA >> PME(D0-,D1-,D2-,D3hot-,D3cold-) >> Status: D0 PME-Enable- DSel=0 DScale=0 PME- >> Capabilities: [d0] Message Signalled Interrupts: Mask- 64bit+ Queue=0/1 >> Enable- >> Address: 0000000000000000 Data: 0000 >> Capabilities: [e0] PCI-X non-bridge device >> Command: DPERE- ERO- RBC=512 OST=4 >> Status: Dev=05:0e.0 64bit+ 133MHz+ SCD- USC- DC=bridge DMMRBC=1024 >> DMOST=4 DMCRS=16 RSCEM- 266MHz- 533MHz- >> Kernel driver in use: megaraid_sas >> Kernel modules: megaraid_sas >> >> I am using a Supermicro X8DALi motherboard with a 5500 chipset. >> >> Whenever I try to access the device the Xen console spits out something >> like this: >> (XEN) [VT-D]iommu.c:796: DMAR:[DMA Write] Request device [05:08.0] fault >> addr 204865000, iommu reg = ffff82c3fff57000 >> (XEN) DMAR:[fault reason 02h] Present bit in context entry is clear >> (XEN) print_vtd_entries: iommu = ffff83013fffaee0 bdf = 5:8.0 gmfn >> 204865 >> (XEN) root_entry = ffff83013ff37000 >> (XEN) root_entry[5] = 13cf12001 >> (XEN) context = ffff83013cf12000 >> (XEN) context[40] = 0_0 >> (XEN) ctxt_entry[40] not present >> (XEN) [VT-D]iommu.c:821: iommu_fault_status: Primary Pending Fault >> >> reads are partially succcessful, but I am getting seek errors at times, >> filesystems will mount properly but I cannot use any of them properly.. >> >> >> The actual kernel output varies, sometimes i get EINVAL when I try to >> read from the filesystem, sometimes it simply refuses to at all >> recognize the disk altogether, and other times it will hang the entire >> system, including the hypervisor itself. >> I''ve tried booting the hypervisor with x2apic disabled, but to no >> effect. I''ve also tried with the latest xen-4.0-testing (4.0.1), buut >> same issue and same outpuut >> >> A quick google turns up a thread, from this mailing list, with a >> different RAID card, but the kernel output is similar.. e.g. >> >> scsi scan: INQUIRY result too short (5), using 36 >> >> http://lists.xensource.com/archives/html/xen-users/2010-04/msg00535.html >> >> The full xen log is below >> >> >> >> L __ __ _ _ ___ >> ___ >> \ \/ /___ _ __ | || | / _ \ / _ \ 0x146000>, shtab=0x3a2078, >> entry=0x100000 >> \ // _ \ ''_ \ | || |_| | | | | | >> | >> / \ __/ | | | |__ _| |_| | |_| |apper/OS-root ro nomodeset >> console=tty0 r >> /_/\_\___|_| |_| | >> _|(_)___(_)___/ >> 020 >> bytes] >> (XEN) Xen version 4.0.0 (mordy@) (gcc version 4.3.2 (Debian 4.3.2-1.1) ) >> Fri May 21 07:50:16 PDT 2010boot-module >> @ >> (XEN) Latest ChangeSet: >> unavailable >> (XEN) Console output is >> synchronous. >> (XEN) Command line: iommu=verbose loglvl=all guest_loglvl=all >> sync_console console_to_rint com1=115200,8n1 >> console=com1 >> (XEN) Video >> information: >> (XEN) VGA is text mode 80x25, font >> 8x16 >> (XEN) VBE/DDC methods: none; EDID transfer time: 0 >> seconds >> (XEN) EDID info not retrieved because no DDC retrieval method >> detected >> (XEN) Disc information: >> (XEN) Found 1 MBR signatures >> (XEN) Found 1 EDD information structures >> (XEN) Xen-e820 RAM map: >> (XEN) 0000000000000000 - 000000000009a000 (usable) >> (XEN) 000000000009a000 - 00000000000a0000 (reserved) >> (XEN) 00000000000e0000 - 0000000000100000 (reserved) >> (XEN) 0000000000100000 - 00000000bf760000 (usable) >> (XEN) 00000000bf76e000 - 00000000bf770000 type 9 >> (XEN) 00000000bf770000 - 00000000bf77e000 (ACPI data) >> (XEN) 00000000bf77e000 - 00000000bf7d0000 (ACPI NVS) >> (XEN) 00000000bf7d0000 - 00000000bf7e0000 (reserved) >> (XEN) 00000000bf7ec000 - 00000000c0000000 (reserved) >> (XEN) 00000000fee00000 - 00000000fee01000 (reserved) >> (XEN) 00000000ffc00000 - 0000000100000000 (reserved) >> (XEN) 0000000100000000 - 0000000340000000 (usable) >> (XEN) ACPI: RSDP 000F9E10, 0024 (r2 ACPIAM) >> (XEN) ACPI: XSDT BF770100, 0094 (r1 NEC 20090424 MSFT >> 97) >> (XEN) ACPI: FACP BF770290, 00F4 (r4 042409 FACP1917 20090424 MSFT >> 97) >> (XEN) ACPI: DSDT BF770670, 5BFB (r2 10601 10601000 0 INTL >> 20051117) >> (XEN) ACPI: FACS BF77E000, 0040 >> (XEN) ACPI: APIC BF770390, 00D2 (r2 042409 APIC1917 20090424 MSFT >> 97) >> (XEN) ACPI: MCFG BF770470, 003C (r1 042409 OEMMCFG 20090424 MSFT >> 97) >> (XEN) ACPI: SLIC BF7704B0, 0176 (r1 NEC 20090424 MSFT >> 97) >> (XEN) ACPI: ERST BF770630, 0040 (r1 042409 WHEA1917 20090424 MSFT >> 97) >> (XEN) ACPI: OEMB BF77E040, 007B (r1 042409 OEMB1917 20090424 MSFT >> 97) >> (XEN) ACPI: SRAT BF77A670, 01D0 (r1 042409 OEMSRAT 1 INTL >> 1) >> (XEN) ACPI: HPET BF77A840, 0038 (r1 042409 OEMHPET 20090424 MSFT >> 97) >> (XEN) ACPI: DMAR BF77E0C0, 0118 (r1 AMI OEMDMAR 1 MSFT >> 97) >> (XEN) ACPI: SSDT BF781DF0, 0363 (r1 DpgPmm CpuPm 12 INTL >> 20051117) >> (XEN) ACPI: EINJ BF77A880, 0130 (r1 AMIER AMI_EINJ 20090424 MSFT >> 97) >> (XEN) ACPI: BERT BF77AA10, 0030 (r1 AMIER AMI_BERT 20090424 MSFT >> 97) >> (XEN) ACPI: ERST BF77AA40, 01B0 (r1 AMIER AMI_ERST 20090424 MSFT >> 97) >> (XEN) ACPI: HEST BF77ABF0, 00A8 (r1 AMIER AMI_HEST 20090424 MSFT >> 97) >> (XEN) System RAM: 12045MB (12334808kB) >> (XEN) SRAT: PXM 0 -> APIC 0 -> Node 0 >> (XEN) SRAT: PXM 0 -> APIC 2 -> Node 0 >> (XEN) SRAT: PXM 0 -> APIC 4 -> Node 0 >> (XEN) SRAT: PXM 0 -> APIC 6 -> Node 0 >> (XEN) SRAT: PXM 0 -> APIC 1 -> Node 0 >> (XEN) SRAT: PXM 0 -> APIC 3 -> Node 0 >> (XEN) SRAT: PXM 0 -> APIC 5 -> Node 0 >> (XEN) SRAT: PXM 0 -> APIC 7 -> Node 0 >> (XEN) SRAT: PXM 1 -> APIC 16 -> Node 1 >> (XEN) SRAT: PXM 1 -> APIC 18 -> Node 1 >> (XEN) SRAT: PXM 1 -> APIC 20 -> Node 1 >> (XEN) SRAT: PXM 1 -> APIC 22 -> Node 1 >> (XEN) SRAT: PXM 1 -> APIC 17 -> Node 1 >> (XEN) SRAT: PXM 1 -> APIC 19 -> Node 1 >> (XEN) SRAT: PXM 1 -> APIC 21 -> Node 1 >> (XEN) SRAT: PXM 1 -> APIC 23 -> Node 1 >> (XEN) SRAT: Node 0 PXM 0 0-a0000 >> (XEN) SRAT: Node 0 PXM 0 100000-c0000000 >> (XEN) SRAT: Node 0 PXM 0 100000000-1c0000000 >> (XEN) SRAT: Node 1 PXM 1 1c0000000-340000000 >> (XEN) NUMA: Allocated memnodemap from 33fdfb000 - 33fdff000 >> (XEN) NUMA: Using 8 for the hash shift. >> (XEN) Domain heap initialised DMA width 30 bits >> (XEN) found SMP MP-table at 000ff780 >> (XEN) DMI present. >> (XEN) Using APIC driver default >> (XEN) ACPI: PM-Timer IO Port: 0x808 >> (XEN) ACPI: ACPI SLEEP INFO: pm1x_cnt[804,0], pm1x_evt[800,0] >> (XEN) ACPI: wakeup_vec[bf77e00c], vec_size[20] >> (XEN) ACPI: Local APIC address 0xfee00000 >> (XEN) ACPI: LAPIC (acpi_id[0x01] lapic_id[0x00] enabled) >> (XEN) Processor #0 7:10 APIC version 21 >> (XEN) ACPI: LAPIC (acpi_id[0x02] lapic_id[0x10] enabled) >> (XEN) Processor #16 7:10 APIC version 21 >> (XEN) ACPI: LAPIC (acpi_id[0x03] lapic_id[0x02] enabled) >> (XEN) Processor #2 7:10 APIC version 21 >> (XEN) ACPI: LAPIC (acpi_id[0x04] lapic_id[0x12] enabled) >> (XEN) Processor #18 7:10 APIC version 21 >> (XEN) ACPI: LAPIC (acpi_id[0x05] lapic_id[0x04] enabled) >> (XEN) Processor #4 7:10 APIC version 21 >> (XEN) ACPI: LAPIC (acpi_id[0x06] lapic_id[0x14] enabled) >> (XEN) Processor #20 7:10 APIC version 21 >> (XEN) ACPI: LAPIC (acpi_id[0x07] lapic_id[0x06] enabled) >> (XEN) Processor #6 7:10 APIC version 21 >> (XEN) ACPI: LAPIC (acpi_id[0x08] lapic_id[0x16] enabled) >> (XEN) Processor #22 7:10 APIC version 21 >> (XEN) ACPI: LAPIC (acpi_id[0x09] lapic_id[0x01] enabled) >> (XEN) Processor #1 7:10 APIC version 21 >> (XEN) ACPI: LAPIC (acpi_id[0x0a] lapic_id[0x11] enabled) >> (XEN) Processor #17 7:10 APIC version 21 >> (XEN) ACPI: LAPIC (acpi_id[0x0b] lapic_id[0x03] enabled) >> (XEN) Processor #3 7:10 APIC version 21 >> (XEN) ACPI: LAPIC (acpi_id[0x0c] lapic_id[0x13] enabled) >> (XEN) Processor #19 7:10 APIC version 21 >> (XEN) ACPI: LAPIC (acpi_id[0x0d] lapic_id[0x05] enabled) >> (XEN) Processor #5 7:10 APIC version 21 >> (XEN) ACPI: LAPIC (acpi_id[0x0e] lapic_id[0x15] enabled) >> (XEN) Processor #21 7:10 APIC version 21 >> (XEN) ACPI: LAPIC (acpi_id[0x0f] lapic_id[0x07] enabled) >> (XEN) Processor #7 7:10 APIC version 21 >> (XEN) ACPI: LAPIC (acpi_id[0x10] lapic_id[0x17] enabled) >> (XEN) Processor #23 7:10 APIC version 21 >> (XEN) ACPI: LAPIC_NMI (acpi_id[0xff] dfl dfl lint[0x1]) >> (XEN) Overriding APIC driver with bigsmp >> (XEN) ACPI: IOAPIC (id[0x08] address[0xfec00000] gsi_base[0]) >> (XEN) IOAPIC[0]: apic_id 8, version 32, address 0xfec00000, GSI 0-23 >> (XEN) ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl) >> (XEN) ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 20 low level) >> (XEN) ACPI: IRQ0 used by override. >> (XEN) ACPI: IRQ2 used by override. >> (XEN) ACPI: IRQ9 used by override. >> (XEN) Enabling APIC mode: Phys. Using 1 I/O APICs >> (XEN) ACPI: HPET id: 0xffffffff base: 0xfed00000 >> (XEN) [VT-D]dmar.c:679: Host address width 40 >> (XEN) [VT-D]dmar.c:694: found ACPI_DMAR_DRHD: >> (XEN) [VT-D]dmar.c:398: dmaru->address = fbffe000 >> (XEN) [VT-D]dmar.c:340: IOAPIC: f0:1f.7 >> (XEN) [VT-D]dmar.c:411: flags: INCLUDE_ALL >> (XEN) [VT-D]dmar.c:699: found ACPI_DMAR_RMRR: >> (XEN) [VT-D]dmar.c:334: endpoint: 0:1d.0 >> (XEN) [VT-D]dmar.c:334: endpoint: 0:1d.1 >> (XEN) [VT-D]dmar.c:334: endpoint: 0:1d.2 >> (XEN) [VT-D]dmar.c:334: endpoint: 0:1d.7 >> (XEN) [VT-D]dmar.c:334: endpoint: 0:1a.0 >> (XEN) [VT-D]dmar.c:334: endpoint: 0:1a.1 >> (XEN) [VT-D]dmar.c:334: endpoint: 0:1a.2 >> (XEN) [VT-D]dmar.c:334: endpoint: 0:1a.7 >> (XEN) [VT-D]dmar.c:571: RMRR region: base_addr ec000 end_address effff >> (XEN) [VT-D]dmar.c:699: found ACPI_DMAR_RMRR: >> (XEN) [VT-D]dmar.c:334: endpoint: 0:1d.0 >> (XEN) [VT-D]dmar.c:334: endpoint: 0:1d.1 >> (XEN) [VT-D]dmar.c:334: endpoint: 0:1d.2 >> (XEN) [VT-D]dmar.c:334: endpoint: 0:1d.7 >> (XEN) [VT-D]dmar.c:334: endpoint: 0:1a.0 >> (XEN) [VT-D]dmar.c:334: endpoint: 0:1a.1 >> (XEN) [VT-D]dmar.c:334: endpoint: 0:1a.2 >> (XEN) [VT-D]dmar.c:334: endpoint: 0:1a.7 >> (XEN) [VT-D]dmar.c:571: RMRR region: base_addr bf7ec000 end_address >> bf7fffff >> (XEN) [VT-D]dmar.c:704: found ACPI_DMAR_ATSR: >> (XEN) [VT-D]dmar.c:599: atsru->all_ports: 0 >> (XEN) [VT-D]dmar.c:320: bridge: 0:1.0 start = 0 sec = 1 sub = 1 >> (XEN) [VT-D]dmar.c:320: bridge: 0:3.0 start = 0 sec = 2 sub = 2 >> (XEN) [VT-D]dmar.c:320: bridge: 0:7.0 start = 0 sec = 3 sub = 3 >> (XEN) PCI: MCFG configuration 0: base e0000000 segment 0 buses 0 - 255 >> (XEN) PCI: Not using MMCONFIG. >> (XEN) Using ACPI (MADT) for SMP configuration information >> (XEN) Using scheduler: SMP Credit Scheduler (credit) >> (XEN) Detected 2266.790 MHz processor. >> (XEN) Initing memory sharing. >> (XEN) VMX: Supported advanced features: >> (XEN) - APIC MMIO access virtualisation >> (XEN) - APIC TPR shadow >> (XEN) - Extended Page Tables (EPT) >> (XEN) - Virtual-Processor Identifiers (VPID) >> (XEN) - Virtual NMI >> (XEN) - MSR direct-access bitmap >> (XEN) HVM: ASIDs enabled. >> (XEN) HVM: VMX enabled >> (XEN) HVM: Hardware Assisted Paging detected. >> (XEN) Intel machine check reporting enabled >> (XEN) [VT-D]iommu.c:1078: drhd->address = fbffe000 iommu->reg >> ffff82c3fff57000 >> (XEN) [VT-D]iommu.c:1080: cap = c90780106f0462 ecap = f0207e >> (XEN) Intel VT-d Snoop Control not supported. >> (XEN) Intel VT-d DMA Passthrough not supported. >> (XEN) Intel VT-d Queued Invalidation supported. >> (XEN) Intel VT-d Interrupt Remapping supported. >> (XEN) I/O virtualisation enabled >> (XEN) I/O virtualisation for PV guests disabled >> (XEN) Total of 16 processors activated. >> (XEN) ENABLING IO-APIC IRQs >> (XEN) -> Using new ACK method >> (XEN) ..TIMER: vector=0xF0 apic1=0 pin1=2 apic2=-1 pin2=-1 >> (XEN) TSC is reliable, synchronization unnecessary >> (XEN) Platform timer is 14.318MHz HPET >> ?(XEN) Allocated console ring of 128 KiB. >> (XEN) microcode.c:73:d32767 microcode: CPU1 resumed >> (XEN) microcode.c:73:d32767 microcode: CPU9 resumed >> (XEN) microcode.c:73:d32767 microcode: CPU14 resumed >> (XEN) microcode.c:73:d32767 microcode: CPU6 resumed >> (XEN) microcode.c:73:d32767 microcode: CPU3 resumed >> (XEN) microcode.c:73:d32767 microcode: CPU11 resumed >> (XEN) microcode.c:73:d32767 microcode: CPU8 resumed >> (XEN) microcode.c:73:d32767 microcode: CPU7 resumed >> (XEN) microcode.c:73:d32767 microcode: CPU15 resumed >> (XEN) microcode.c:73:d32767 microcode: CPU2 resumed >> (XEN) microcode.c:73:d32767 microcode: CPU5 resumed >> (XEN) microcode.c:73:d32767 microcode: CPU13 resumed >> (XEN) microcode.c:73:d32767 microcode: CPU4 resumed >> (XEN) microcode.c:73:d32767 microcode: CPU10 resumed >> (XEN) Brought up 16 CPUs >> (XEN) microcode.c:73:d32767 microcode: CPU12 resumed >> (XEN) Turbo Mode detected! >> (XEN) HPET''s MSI mode hasn''t been supported when Interrupt Remapping is >> enabled. >> (XEN) ACPI sleep modes: S3 >> (XEN) mcheck_poll: Machine check polling timer started. >> (XEN) [VT-D]iommu.c:1325: d0:PCIe: map bdf = 0:0.0 >> (XEN) [VT-D]iommu.c:1325: d0:PCIe: map bdf = 0:14.0 >> (XEN) [VT-D]iommu.c:1325: d0:PCIe: map bdf = 0:14.1 >> (XEN) [VT-D]iommu.c:1325: d0:PCIe: map bdf = 0:14.2 >> (XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = 0:14.3 >> (XEN) [VT-D]iommu.c:1325: d0:PCIe: map bdf = 0:16.0 >> (XEN) [VT-D]iommu.c:1325: d0:PCIe: map bdf = 0:16.1 >> (XEN) [VT-D]iommu.c:1325: d0:PCIe: map bdf = 0:16.2 >> (XEN) [VT-D]iommu.c:1325: d0:PCIe: map bdf = 0:16.3 >> (XEN) [VT-D]iommu.c:1325: d0:PCIe: map bdf = 0:16.4 >> (XEN) [VT-D]iommu.c:1325: d0:PCIe: map bdf = 0:16.5 >> (XEN) [VT-D]iommu.c:1325: d0:PCIe: map bdf = 0:16.6 >> (XEN) [VT-D]iommu.c:1325: d0:PCIe: map bdf = 0:16.7 >> (XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = 0:1a.0 >> (XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = 0:1a.1 >> (XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = 0:1a.2 >> (XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = 0:1a.7 >> (XEN) [VT-D]iommu.c:1325: d0:PCIe: map bdf = 0:1b.0 >> (XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = 0:1d.0 >> (XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = 0:1d.1 >> (XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = 0:1d.2 >> (XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = 0:1d.7 >> (XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = 0:1f.0 >> (XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = 0:1f.2 >> (XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = 0:1f.3 >> (XEN) [VT-D]iommu.c:1325: d0:PCIe: map bdf = 1:0.0 >> (XEN) [VT-D]iommu.c:1325: d0:PCIe: map bdf = 3:0.0 >> (XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = 5:e.0 >> (XEN) [VT-D]iommu.c:1325: d0:PCIe: map bdf = 7:0.0 >> (XEN) [VT-D]iommu.c:1325: d0:PCIe: map bdf = 8:0.0 >> (XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = fe:0.0 >> (XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = fe:0.1 >> (XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = fe:2.0 >> (XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = fe:2.1 >> (XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = fe:2.4 >> (XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = fe:2.5 >> (XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = fe:3.0 >> (XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = fe:3.1 >> (XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = fe:3.2 >> (XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = fe:3.4 >> (XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = fe:4.0 >> (XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = fe:4.1 >> (XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = fe:4.2 >> (XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = fe:4.3 >> (XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = fe:5.0 >> (XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = fe:5.1 >> (XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = fe:5.2 >> (XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = fe:5.3 >> (XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = fe:6.0 >> (XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = fe:6.1 >> (XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = fe:6.2 >> (XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = fe:6.3 >> (XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = ff:0.0 >> (XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = ff:0.1 >> (XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = ff:2.0 >> (XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = ff:2.1 >> (XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = ff:2.4 >> (XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = ff:2.5 >> (XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = ff:3.0 >> (XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = ff:3.1 >> (XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = ff:3.2 >> (XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = ff:3.4 >> (XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = ff:4.0 >> (XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = ff:4.1 >> (XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = ff:4.2 >> (XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = ff:4.3 >> (XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = ff:5.0 >> (XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = ff:5.1 >> (XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = ff:5.2 >> (XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = ff:5.3 >> (XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = ff:6.0 >> (XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = ff:6.1 >> (XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = ff:6.2 >> (XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = ff:6.3 >> (XEN) [VT-D]iommu.c:695: iommu_enable_translation: iommu->reg >> ffff82c3fff57000 >> (XEN) *** LOADING DOMAIN 0 *** >> (XEN) Xen kernel: 64-bit, lsb, compat32 >> (XEN) Dom0 kernel: 64-bit, PAE, lsb, paddr 0x1000000 -> 0x26b6000 >> (XEN) PHYSICAL MEMORY ARRANGEMENT: >> (XEN) Dom0 alloc.: 0000000100000000->0000000120000000 (2937045 pages >> to be allocated) >> (XEN) VIRTUAL MEMORY ARRANGEMENT: >> (XEN) Loaded kernel: ffffffff81000000->ffffffff826b6000 >> (XEN) Init. ramdisk: ffffffff826b6000->ffffffff8f7d7600 >> (XEN) Phys-Mach map: ffffffff8f7d8000->ffffffff90f406a8 >> (XEN) Start info: ffffffff90f41000->ffffffff90f414b4 >> (XEN) Page tables: ffffffff90f42000->ffffffff90fcf000 >> (XEN) Boot stack: ffffffff90fcf000->ffffffff90fd0000 >> (XEN) TOTAL: ffffffff80000000->ffffffff91400000 >> (XEN) ENTRY ADDRESS: ffffffff819be200 >> (XEN) Dom0 has maximum 16 VCPUs >> (XEN) Scrubbing Free RAM: .done. >> (XEN) Xen trace buffers: disabled >> (XEN) Std. Loglevel: All >> (XEN) Guest Loglevel: All >> (XEN) ********************************************** >> (XEN) ******* WARNING: CONSOLE OUTPUT IS SYNCHRONOUS >> (XEN) ******* This option is intended to aid debugging of Xen by >> ensuring >> (XEN) ******* that all output is synchronously delivered on the serial >> line. >> (XEN) ******* However it can introduce SIGNIFICANT latencies and affect >> (XEN) ******* timekeeping. It is NOT recommended for production use! >> (XEN) ********************************************** >> (XEN) 3... 2... 1... >> (XEN) *** Serial input -> DOM0 (type ''CTRL-a'' three times to switch >> input to Xen) >> (XEN) Freed 164kB init memory. >> mapping kernel into physical memory >> Xen: setup ISA identity maps >> about to get started... >> (XEN) PCI add device 00:00.0 >> (XEN) PCI add device 00:01.0 >> (XEN) PCI add device 00:03.0 >> (XEN) PCI add device 00:07.0 >> (XEN) PCI add device 00:14.0 >> (XEN) PCI add device 00:14.1 >> (XEN) PCI add device 00:14.2 >> (XEN) PCI add device 00:14.3 >> (XEN) PCI add device 00:16.0 >> (XEN) PCI add device 00:16.1 >> (XEN) PCI add device 00:16.2 >> (XEN) PCI add device 00:16.3 >> (XEN) PCI add device 00:16.4 >> (XEN) PCI add device 00:16.5 >> (XEN) PCI add device 00:16.6 >> (XEN) PCI add device 00:16.7 >> (XEN) PCI add device 00:1a.0 >> (XEN) PCI add device 00:1a.1 >> (XEN) PCI add device 00:1a.2 >> (XEN) PCI add device 00:1a.7 >> (XEN) PCI add device 00:1b.0 >> (XEN) PCI add device 00:1c.0 >> (XEN) PCI add device 00:1c.4 >> (XEN) PCI add device 00:1c.5 >> (XEN) PCI add device 00:1d.0 >> (XEN) PCI add device 00:1d.1 >> (XEN) PCI add device 00:1d.2 >> (XEN) PCI add device 00:1d.7 >> (XEN) PCI add device 00:1e.0 >> (XEN) PCI add device 00:1f.0 >> (XEN) PCI add device 00:1f.2 >> (XEN) PCI add device 00:1f.3 >> (XEN) PCI add device 01:00.0 >> (XEN) PCI add device 03:00.0 >> (XEN) PCI add device 04:00.0 >> (XEN) PCI add device 04:00.2 >> (XEN) PCI add device 05:0e.0 >> (XEN) PCI add device 07:00.0 >> (XEN) PCI add device 08:00.0 >> (XEN) cpuid.MWAIT[.eax=40, .ebx=40, .ecx=3, .edx=1120] >> (XEN) Monitor-Mwait will be used to enter C-1 state >> (XEN) cpuid.MWAIT[.eax=40, .ebx=40, .ecx=3, .edx=1120] >> (XEN) Monitor-Mwait will be used to enter C-3 state >> (XEN) cpuid.MWAIT[.eax=40, .ebx=40, .ecx=3, .edx=1120] >> (XEN) Monitor-Mwait will be used to enter C-3 state >> (XEN) cpuid.MWAIT[.eax=40, .ebx=40, .ecx=3, .edx=1120] >> (XEN) Monitor-Mwait will be used to enter C-1 state >> (XEN) cpuid.MWAIT[.eax=40, .ebx=40, .ecx=3, .edx=1120] >> (XEN) Monitor-Mwait will be used to enter C-3 state >> (XEN) cpuid.MWAIT[.eax=40, .ebx=40, .ecx=3, .edx=1120] >> (XEN) Monitor-Mwait will be used to enter C-3 state >> (XEN) cpuid.MWAIT[.eax=40, .ebx=40, .ecx=3, .edx=1120] >> (XEN) Monitor-Mwait will be used to enter C-1 state >> (XEN) cpuid.MWAIT[.eax=40, .ebx=40, .ecx=3, .edx=1120] >> (XEN) Monitor-Mwait will be used to enter C-3 state >> (XEN) cpuid.MWAIT[.eax=40, .ebx=40, .ecx=3, .edx=1120] >> (XEN) Monitor-Mwait will be used to enter C-3 state >> (XEN) cpuid.MWAIT[.eax=40, .ebx=40, .ecx=3, .edx=1120] >> (XEN) Monitor-Mwait will be used to enter C-1 state >> (XEN) cpuid.MWAIT[.eax=40, .ebx=40, .ecx=3, .edx=1120] >> (XEN) Monitor-Mwait will be used to enter C-3 state >> (XEN) cpuid.MWAIT[.eax=40, .ebx=40, .ecx=3, .edx=1120] >> (XEN) Monitor-Mwait will be used to enter C-3 state >> (XEN) cpuid.MWAIT[.eax=40, .ebx=40, .ecx=3, .edx=1120] >> (XEN) Monitor-Mwait will be used to enter C-1 state >> (XEN) cpuid.MWAIT[.eax=40, .ebx=40, .ecx=3, .edx=1120] >> (XEN) Monitor-Mwait will be used to enter C-3 state >> (XEN) cpuid.MWAIT[.eax=40, .ebx=40, .ecx=3, .edx=1120] >> (XEN) Monitor-Mwait will be used to enter C-3 state >> (XEN) cpuid.MWAIT[.eax=40, .ebx=40, .ecx=3, .edx=1120] >> (XEN) Monitor-Mwait will be used to enter C-1 state >> (XEN) cpuid.MWAIT[.eax=40, .ebx=40, .ecx=3, .edx=1120] >> (XEN) Monitor-Mwait will be used to enter C-3 state >> (XEN) cpuid.MWAIT[.eax=40, .ebx=40, .ecx=3, .edx=1120] >> (XEN) Monitor-Mwait will be used to enter C-3 state >> (XEN) cpuid.MWAIT[.eax=40, .ebx=40, .ecx=3, .edx=1120] >> (XEN) Monitor-Mwait will be used to enter C-1 state >> (XEN) cpuid.MWAIT[.eax=40, .ebx=40, .ecx=3, .edx=1120] >> (XEN) Monitor-Mwait will be used to enter C-3 state >> (XEN) cpuid.MWAIT[.eax=40, .ebx=40, .ecx=3, .edx=1120] >> (XEN) Monitor-Mwait will be used to enter C-3 state >> (XEN) cpuid.MWAIT[.eax=40, .ebx=40, .ecx=3, .edx=1120] >> (XEN) Monitor-Mwait will be used to enter C-1 state >> (XEN) cpuid.MWAIT[.eax=40, .ebx=40, .ecx=3, .edx=1120] >> (XEN) Monitor-Mwait will be used to enter C-3 state >> (XEN) cpuid.MWAIT[.eax=40, .ebx=40, .ecx=3, .edx=1120] >> (XEN) Monitor-Mwait will be used to enter C-3 state >> (XEN) cpuid.MWAIT[.eax=40, .ebx=40, .ecx=3, .edx=1120] >> (XEN) Monitor-Mwait will be used to enter C-1 state >> (XEN) cpuid.MWAIT[.eax=40, .ebx=40, .ecx=3, .edx=1120] >> (XEN) Monitor-Mwait will be used to enter C-3 state >> (XEN) cpuid.MWAIT[.eax=40, .ebx=40, .ecx=3, .edx=1120] >> (XEN) Monitor-Mwait will be used to enter C-3 state >> (XEN) cpuid.MWAIT[.eax=40, .ebx=40, .ecx=3, .edx=1120] >> (XEN) Monitor-Mwait will be used to enter C-1 state >> (XEN) cpuid.MWAIT[.eax=40, .ebx=40, .ecx=3, .edx=1120] >> (XEN) Monitor-Mwait will be used to enter C-3 state >> (XEN) cpuid.MWAIT[.eax=40, .ebx=40, .ecx=3, .edx=1120] >> (XEN) Monitor-Mwait will be used to enter C-3 state >> (XEN) cpuid.MWAIT[.eax=40, .ebx=40, .ecx=3, .edx=1120] >> (XEN) Monitor-Mwait will be used to enter C-1 state >> (XEN) cpuid.MWAIT[.eax=40, .ebx=40, .ecx=3, .edx=1120] >> (XEN) Monitor-Mwait will be used to enter C-3 state >> (XEN) cpuid.MWAIT[.eax=40, .ebx=40, .ecx=3, .edx=1120] >> (XEN) Monitor-Mwait will be used to enter C-3 state >> (XEN) cpuid.MWAIT[.eax=40, .ebx=40, .ecx=3, .edx=1120] >> (XEN) Monitor-Mwait will be used to enter C-1 state >> (XEN) cpuid.MWAIT[.eax=40, .ebx=40, .ecx=3, .edx=1120] >> (XEN) Monitor-Mwait will be used to enter C-3 state >> (XEN) cpuid.MWAIT[.eax=40, .ebx=40, .ecx=3, .edx=1120] >> (XEN) Monitor-Mwait will be used to enter C-3 state >> (XEN) cpuid.MWAIT[.eax=40, .ebx=40, .ecx=3, .edx=1120] >> (XEN) Monitor-Mwait will be used to enter C-1 state >> (XEN) cpuid.MWAIT[.eax=40, .ebx=40, .ecx=3, .edx=1120] >> (XEN) Monitor-Mwait will be used to enter C-3 state >> (XEN) cpuid.MWAIT[.eax=40, .ebx=40, .ecx=3, .edx=1120] >> (XEN) Monitor-Mwait will be used to enter C-3 state >> (XEN) cpuid.MWAIT[.eax=40, .ebx=40, .ecx=3, .edx=1120] >> (XEN) Monitor-Mwait will be used to enter C-1 state >> (XEN) cpuid.MWAIT[.eax=40, .ebx=40, .ecx=3, .edx=1120] >> (XEN) Monitor-Mwait will be used to enter C-3 state >> (XEN) cpuid.MWAIT[.eax=40, .ebx=40, .ecx=3, .edx=1120] >> (XEN) Monitor-Mwait will be used to enter C-3 state >> (XEN) cpuid.MWAIT[.eax=40, .ebx=40, .ecx=3, .edx=1120] >> (XEN) Monitor-Mwait will be used to enter C-1 state >> (XEN) cpuid.MWAIT[.eax=40, .ebx=40, .ecx=3, .edx=1120] >> (XEN) Monitor-Mwait will be used to enter C-3 state >> (XEN) cpuid.MWAIT[.eax=40, .ebx=40, .ecx=3, .edx=1120] >> (XEN) Monitor-Mwait will be used to enter C-3 state >> (XEN) cpuid.MWAIT[.eax=40, .ebx=40, .ecx=3, .edx=1120] >> (XEN) Monitor-Mwait will be used to enter C-1 state >> (XEN) cpuid.MWAIT[.eax=40, .ebx=40, .ecx=3, .edx=1120] >> (XEN) Monitor-Mwait will be used to enter C-3 state >> (XEN) cpuid.MWAIT[.eax=40, .ebx=40, .ecx=3, .edx=1120] >> (XEN) Monitor-Mwait will be used to enter C-3 state >> (XEN) irq.c:1139:d0 Cannot bind IRQ 4 to guest. In use by ''ns16550''. >> (XEN) irq.c:1139:d0 Cannot bind IRQ 2 to guest. In use by ''cascade''. >> (XEN) irq.c:1139:d0 Cannot bind IRQ 4 to guest. In use by ''ns16550''. >> (XEN) irq.c:1139:d0 Cannot bind IRQ 2 to guest. In use by ''cascade''. >> (XEN) irq.c:1139:d0 Cannot bind IRQ 4 to guest. In use by ''ns16550''. >> (XEN) irq.c:1139:d0 Cannot bind IRQ 2 to guest. In use by ''cascade''. >> (XEN) irq.c:1139:d0 Cannot bind IRQ 4 to guest. In use by ''ns16550''. >> (XEN) irq.c:1139:d0 Cannot bind IRQ 2 to guest. In use by ''cascade''. >> (XEN) [VT-D]iommu.c:821: iommu_fault_status: Primary Pending Fault >> (XEN) [VT-D]iommu.c:796: DMAR:[DMA Write] Request device [05:08.0] fault >> addr 203a09000, iommu reg = ffff82c3fff57000 >> (XEN) DMAR:[fault reason 02h] Present bit in context entry is clear >> (XEN) print_vtd_entries: iommu = ffff83013fffaee0 bdf = 5:8.0 gmfn >> 203a09 >> (XEN) root_entry = ffff83013ff37000 >> (XEN) root_entry[5] = 13cf12001 >> (XEN) context = ffff83013cf12000 >> (XEN) context[40] = 0_0 >> (XEN) ctxt_entry[40] not present >> (XEN) [VT-D]iommu.c:796: DMAR:[DMA Write] Request device [05:08.0] fault >> addr 203eba000, iommu reg = ffff82c3fff57000 >> (XEN) DMAR:[fault reason 02h] Present bit in context entry is clear >> (XEN) print_vtd_entries: iommu = ffff83013fffaee0 bdf = 5:8.0 gmfn >> 203eba >> (XEN) root_entry = ffff83013ff37000 >> (XEN) root_entry[5] = 13cf12001 >> (XEN) context = ffff83013cf12000 >> (XEN) context[40] = 0_0 >> (XEN) ctxt_entry[40] not present >> (XEN) [VT-D]iommu.c:821: iommu_fault_status: Primary Pending Fault >> (XEN) [VT-D]iommu.c:796: DMAR:[DMA Write] Request device [05:08.0] fault >> addr 204e11000, iommu reg = ffff82c3fff57000 >> (XEN) DMAR:[fault reason 02h] Present bit in context entry is clear >> (XEN) print_vtd_entries: iommu = ffff83013fffaee0 bdf = 5:8.0 gmfn >> 204e11 >> (XEN) root_entry = ffff83013ff37000 >> (XEN) root_entry[5] = 13cf12001 >> (XEN) context = ffff83013cf12000 >> (XEN) context[40] = 0_0 >> (XEN) ctxt_entry[40] not present >> (XEN) [VT-D]iommu.c:821: iommu_fault_status: Primary Pending Fault >> (XEN) [VT-D]iommu.c:796: DMAR:[DMA Write] Request device [05:08.0] fault >> addr 2061e2000, iommu reg = ffff82c3fff57000 >> (XEN) DMAR:[fault reason 02h] Present bit in context entry is clear >> (XEN) print_vtd_entries: iommu = ffff83013fffaee0 bdf = 5:8.0 gmfn >> 2061e2 >> (XEN) root_entry = ffff83013ff37000 >> (XEN) root_entry[5] = 13cf12001 >> (XEN) context = ffff83013cf12000 >> (XEN) context[40] = 0_0 >> (XEN) ctxt_entry[40] not present >> (XEN) [VT-D]iommu.c:796: DMAR:[DMA Write] Request device [05:08.0] fault >> addr 205043000, iommu reg = ffff82c3fff57000 >> (XEN) DMAR:[fault reason 02h] Present bit in context entry is clear >> (XEN) print_vtd_entries: iommu = ffff83013fffaee0 bdf = 5:8.0 gmfn >> 205043 >> (XEN) root_entry = ffff83013ff37000 >> (XEN) root_entry[5] = 13cf12001 >> (XEN) context = ffff83013cf12000 >> (XEN) context[40] = 0_0 >> (XEN) ctxt_entry[40] not present >> (XEN) [VT-D]iommu.c:821: iommu_fault_status: Primary Pending Fault >> (XEN) [VT-D]iommu.c:796: DMAR:[DMA Write] Request device [05:08.0] fault >> addr 20552b000, iommu reg = ffff82c3fff57000 >> (XEN) DMAR:[fault reason 02h] Present bit in context entry is clear >> (XEN) print_vtd_entries: iommu = ffff83013fffaee0 bdf = 5:8.0 gmfn >> 20552b >> (XEN) root_entry = ffff83013ff37000 >> (XEN) root_entry[5] = 13cf12001 >> (XEN) context = ffff83013cf12000 >> (XEN) context[40] = 0_0 >> (XEN) ctxt_entry[40] not present >> (XEN) [VT-D]iommu.c:821: iommu_fault_status: Primary Pending Fault >> (XEN) [VT-D]iommu.c:796: DMAR:[DMA Write] Request device [05:08.0] fault >> addr 205708000, iommu reg = ffff82c3fff57000 >> (XEN) DMAR:[fault reason 02h] Present bit in context entry is clear >> (XEN) print_vtd_entries: iommu = ffff83013fffaee0 bdf = 5:8.0 gmfn >> 205708 >> (XEN) root_entry = ffff83013ff37000 >> (XEN) root_entry[5] = 13cf12001 >> (XEN) context = ffff83013cf12000 >> (XEN) context[40] = 0_0 >> (XEN) ctxt_entry[40] not present >> (XEN) [VT-D]iommu.c:796: DMAR:[DMA Write] Request device [05:08.0] fault >> addr 2060c0000, iommu reg = ffff82c3fff57000 >> (XEN) DMAR:[fault reason 02h] Present bit in context entry is clear >> (XEN) print_vtd_entries: iommu = ffff83013fffaee0 bdf = 5:8.0 gmfn >> 2060c0 >> (XEN) root_entry = ffff83013ff37000 >> (XEN) root_entry[5] = 13cf12001 >> (XEN) context = ffff83013cf12000 >> (XEN) context[40] = 0_0 >> (XEN) ctxt_entry[40] not present >> (XEN) [VT-D]iommu.c:821: iommu_fault_status: Primary Pending Fault >> (XEN) [VT-D]iommu.c:796: DMAR:[DMA Write] Request device [05:08.0] fault >> addr 206591000, iommu reg = ffff82c3fff57000 >> (XEN) DMAR:[fault reason 02h] Present bit in context entry is clear >> (XEN) print_vtd_entries: iommu = ffff83013fffaee0 bdf = 5:8.0 gmfn >> 206591 >> (XEN) root_entry = ffff83013ff37000 >> (XEN) root_entry[5] = 13cf12001 >> (XEN) context = ffff83013cf12000 >> (XEN) context[40] = 0_0 >> (XEN) ctxt_entry[40] not present >> (XEN) [VT-D]iommu.c:796: DMAR:[DMA Write] Request device [05:08.0] fault >> addr 204353000, iommu reg = ffff82c3fff57000 >> (XEN) DMAR:[fault reason 02h] Present bit in context entry is clear >> (XEN) print_vtd_entries: iommu = ffff83013fffaee0 bdf = 5:8.0 gmfn >> 204353 >> (XEN) root_entry = ffff83013ff37000 >> (XEN) root_entry[5] = 13cf12001 >> (XEN) context = ffff83013cf12000 >> (XEN) context[40] = 0_0 >> (XEN) ctxt_entry[40] not present >> (XEN) [VT-D]iommu.c:821: iommu_fault_status: Primary Pending Fault >> (XEN) [VT-D]iommu.c:796: DMAR:[DMA Write] Request device [05:08.0] fault >> addr 2061f2000, iommu reg = ffff82c3fff57000 >> (XEN) DMAR:[fault reason 02h] Present bit in context entry is clear >> (XEN) print_vtd_entries: iommu = ffff83013fffaee0 bdf = 5:8.0 gmfn >> 2061f2 >> (XEN) root_entry = ffff83013ff37000 >> (XEN) root_entry[5] = 13cf12001 >> (XEN) context = ffff83013cf12000 >> (XEN) context[40] = 0_0 >> (XEN) ctxt_entry[40] not present >> (XEN) [VT-D]iommu.c:796: DMAR:[DMA Write] Request device [05:08.0] fault >> addr 204306000, iommu reg = ffff82c3fff57000 >> (XEN) DMAR:[fault reason 02h] Present bit in context entry is clear >> (XEN) print_vtd_entries: iommu = ffff83013fffaee0 bdf = 5:8.0 gmfn >> 204306 >> (XEN) root_entry = ffff83013ff37000 >> (XEN) root_entry[5] = 13cf12001 >> (XEN) context = ffff83013cf12000 >> (XEN) context[40] = 0_0 >> (XEN) ctxt_entry[40] not present >> (XEN) [VT-D]iommu.c:821: iommu_fault_status: Primary Pending Fault >> (XEN) [VT-D]iommu.c:796: DMAR:[DMA Write] Request device [05:08.0] fault >> addr 205f6b000, iommu reg = ffff82c3fff57000 >> (XEN) DMAR:[fault reason 02h] Present bit in context entry is clear >> (XEN) print_vtd_entries: iommu = ffff83013fffaee0 bdf = 5:8.0 gmfn >> 205f6b >> (XEN) root_entry = ffff83013ff37000 >> (XEN) root_entry[5] = 13cf12001 >> (XEN) context = ffff83013cf12000 >> (XEN) context[40] = 0_0 >> (XEN) ctxt_entry[40] not present >> (XEN) [VT-D]iommu.c:796: DMAR:[DMA Write] Request device [05:08.0] fault >> addr 205665000, iommu reg = ffff82c3fff57000 >> (XEN) DMAR:[fault reason 02h] Present bit in context entry is clear >> (XEN) print_vtd_entries: iommu = ffff83013fffaee0 bdf = 5:8.0 gmfn >> 205665 >> (XEN) root_entry = ffff83013ff37000 >> (XEN) root_entry[5] = 13cf12001 >> (XEN) context = ffff83013cf12000 >> (XEN) context[40] = 0_0 >> (XEN) ctxt_entry[40] not present >> (XEN) [VT-D]iommu.c:821: iommu_fault_status: Primary Pending Fault >> (XEN) [VT-D]iommu.c:796: DMAR:[DMA Write] Request device [05:08.0] fault >> addr 2045a0000, iommu reg = ffff82c3fff57000 >> (XEN) DMAR:[fault reason 02h] Present bit in context entry is clear >> (XEN) print_vtd_entries: iommu = ffff83013fffaee0 bdf = 5:8.0 gmfn >> 2045a0 >> (XEN) root_entry = ffff83013ff37000 >> (XEN) root_entry[5] = 13cf12001 >> (XEN) context = ffff83013cf12000 >> (XEN) context[40] = 0_0 >> (XEN) ctxt_entry[40] not present >> (XEN) [VT-D]iommu.c:796: DMAR:[DMA Write] Request device [05:08.0] fault >> addr 205669000, iommu reg = ffff82c3fff57000 >> (XEN) DMAR:[fault reason 02h] Present bit in context entry is clear >> (XEN) print_vtd_entries: iommu = ffff83013fffaee0 bdf = 5:8.0 gmfn >> 205669 >> (XEN) root_entry = ffff83013ff37000 >> (XEN) root_entry[5] = 13cf12001 >> (XEN) context = ffff83013cf12000 >> (XEN) context[40] = 0_0 >> (XEN) ctxt_entry[40] not present >> (XEN) [VT-D]iommu.c:821: iommu_fault_status: Primary Pending Fault >> (XEN) [VT-D]iommu.c:796: DMAR:[DMA Write] Request device [05:08.0] fault >> addr 2042c6000, iommu reg = ffff82c3fff57000 >> (XEN) DMAR:[fault reason 02h] Present bit in context entry is clear >> (XEN) print_vtd_entries: iommu = ffff83013fffaee0 bdf = 5:8.0 gmfn >> 2042c6 >> (XEN) root_entry = ffff83013ff37000 >> (XEN) root_entry[5] = 13cf12001 >> (XEN) context = ffff83013cf12000 >> (XEN) context[40] = 0_0 >> (XEN) ctxt_entry[40] not present >> (XEN) [VT-D]iommu.c:796: DMAR:[DMA Write] Request device [05:08.0] fault >> addr 2061fe000, iommu reg = ffff82c3fff57000 >> (XEN) DMAR:[fault reason 02h] Present bit in context entry is clear >> (XEN) print_vtd_entries: iommu = ffff83013fffaee0 bdf = 5:8.0 gmfn >> 2061fe >> (XEN) root_entry = ffff83013ff37000 >> (XEN) root_entry[5] = 13cf12001 >> (XEN) context = ffff83013cf12000 >> (XEN) context[40] = 0_0 >> (XEN) ctxt_entry[40] not present >> (XEN) [VT-D]iommu.c:821: iommu_fault_status: Primary Pending Fault >> (XEN) [VT-D]iommu.c:796: DMAR:[DMA Write] Request device [05:08.0] fault >> addr 20560a000, iommu reg = ffff82c3fff57000 >> (XEN) DMAR:[fault reason 02h] Present bit in context entry is clear >> (XEN) print_vtd_entries: iommu = ffff83013fffaee0 bdf = 5:8.0 gmfn >> 20560a >> (XEN) root_entry = ffff83013ff37000 >> (XEN) root_entry[5] = 13cf12001 >> (XEN) context = ffff83013cf12000 >> (XEN) context[40] = 0_0 >> (XEN) ctxt_entry[40] not present >> (XEN) [VT-D]iommu.c:796: DMAR:[DMA Write] Request device [05:08.0] fault >> addr 206003000, iommu reg = ffff82c3fff57000 >> (XEN) DMAR:[fault reason 02h] Present bit in context entry is clear >> (XEN) print_vtd_entries: iommu = ffff83013fffaee0 bdf = 5:8.0 gmfn >> 206003 >> (XEN) root_entry = ffff83013ff37000 >> (XEN) root_entry[5] = 13cf12001 >> (XEN) context = ffff83013cf12000 >> (XEN) context[40] = 0_0 >> (XEN) ctxt_entry[40] not present >> (XEN) [VT-D]iommu.c:821: iommu_fault_status: Primary Pending Fault >> (XEN) [VT-D]iommu.c:796: DMAR:[DMA Write] Request device [05:08.0] fault >> addr 20583e000, iommu reg = ffff82c3fff57000 >> (XEN) DMAR:[fault reason 02h] Present bit in context entry is clear >> (XEN) print_vtd_entries: iommu = ffff83013fffaee0 bdf = 5:8.0 gmfn >> 20583e >> (XEN) root_entry = ffff83013ff37000 >> (XEN) root_entry[5] = 13cf12001 >> (XEN) context = ffff83013cf12000 >> (XEN) context[40] = 0_0 >> (XEN) ctxt_entry[40] not present >> (XEN) [VT-D]iommu.c:796: DMAR:[DMA Write] Request device [05:08.0] fault >> addr 205615000, iommu reg = ffff82c3fff57000 >> (XEN) DMAR:[fault reason 02h] Present bit in context entry is clear >> (XEN) print_vtd_entries: iommu = ffff83013fffaee0 bdf = 5:8.0 gmfn >> 205615 >> (XEN) root_entry = ffff83013ff37000 >> (XEN) root_entry[5] = 13cf12001 >> (XEN) context = ffff83013cf12000 >> (XEN) context[40] = 0_0 >> (XEN) ctxt_entry[40] not present >> (XEN) [VT-D]iommu.c:796: DMAR:[DMA Write] Request device [05:08.0] fault >> addr 204265000, iommu reg = ffff82c3fff57000 >> (XEN) DMAR:[fault reason 02h] Present bit in context entry is clear >> (XEN) print_vtd_entries: iommu = ffff83013fffaee0 bdf = 5:8.0 gmfn >> 204265 >> (XEN) root_entry = ffff83013ff37000 >> (XEN) root_entry[5] = 13cf12001 >> (XEN) context = ffff83013cf12000 >> (XEN) context[40] = 0_0 >> (XEN) ctxt_entry[40] not present >> (XEN) [VT-D]iommu.c:821: iommu_fault_status: Primary Pending Fault >> (XEN) [VT-D]iommu.c:796: DMAR:[DMA Write] Request device [05:08.0] fault >> addr 207498000, iommu reg = ffff82c3fff57000 >> (XEN) DMAR:[fault reason 02h] Present bit in context entry is clear >> (XEN) print_vtd_entries: iommu = ffff83013fffaee0 bdf = 5:8.0 gmfn >> 207498 >> (XEN) root_entry = ffff83013ff37000 >> (XEN) root_entry[5] = 13cf12001 >> (XEN) context = ffff83013cf12000 >> (XEN) context[40] = 0_0 >> (XEN) ctxt_entry[40] not present >> (XEN) [VT-D]iommu.c:821: iommu_fault_status: Primary Pending Fault >> (XEN) [VT-D]iommu.c:796: DMAR:[DMA Write] Request device [05:08.0] fault >> addr 2049d1000, iommu reg = ffff82c3fff57000 >> (XEN) DMAR:[fault reason 02h] Present bit in context entry is clear >> (XEN) print_vtd_entries: iommu = ffff83013fffaee0 bdf = 5:8.0 gmfn >> 2049d1 >> (XEN) root_entry = ffff83013ff37000 >> (XEN) root_entry[5] = 13cf12001 >> (XEN) context = ffff83013cf12000 >> (XEN) context[40] = 0_0 >> (XEN) ctxt_entry[40] not present >> (XEN) [VT-D]iommu.c:821: iommu_fault_status: Primary Pending Fault >> (XEN) [VT-D]iommu.c:796: DMAR:[DMA Write] Request device [05:08.0] fault >> addr 20488e000, iommu reg = ffff82c3fff57000 >> (XEN) DMAR:[fault reason 02h] Present bit in context entry is clear >> (XEN) print_vtd_entries: iommu = ffff83013fffaee0 bdf = 5:8.0 gmfn >> 20488e >> (XEN) root_entry = ffff83013ff37000 >> (XEN) root_entry[5] = 13cf12001 >> (XEN) context = ffff83013cf12000 >> (XEN) context[40] = 0_0 >> (XEN) ctxt_entry[40] not present >> (XEN) [VT-D]iommu.c:821: iommu_fault_status: Primary Pending Fault >> (XEN) [VT-D]iommu.c:796: DMAR:[DMA Write] Request device [05:08.0] fault >> addr 205495000, iommu reg = ffff82c3fff57000 >> (XEN) DMAR:[fault reason 02h] Present bit in context entry is clear >> (XEN) print_vtd_entries: iommu = ffff83013fffaee0 bdf = 5:8.0 gmfn >> 205495 >> (XEN) root_entry = ffff83013ff37000 >> (XEN) root_entry[5] = 13cf12001 >> (XEN) context = ffff83013cf12000 >> (XEN) context[40] = 0_0 >> (XEN) ctxt_entry[40] not present >> (XEN) [VT-D]iommu.c:821: iommu_fault_status: Primary Pending Fault >> (XEN) [VT-D]iommu.c:796: DMAR:[DMA Write] Request device [05:08.0] fault >> addr 2072d8000, iommu reg = ffff82c3fff57000 >> (XEN) DMAR:[fault reason 02h] Present bit in context entry is clear >> (XEN) print_vtd_entries: iommu = ffff83013fffaee0 bdf = 5:8.0 gmfn >> 2072d8 >> (XEN) root_entry = ffff83013ff37000 >> (XEN) root_entry[5] = 13cf12001 >> (XEN) context = ffff83013cf12000 >> (XEN) context[40] = 0_0 >> (XEN) ctxt_entry[40] not present >> (XEN) [VT-D]iommu.c:821: iommu_fault_status: Primary Pending Fault >> (XEN) [VT-D]iommu.c:796: DMAR:[DMA Write] Request device [05:08.0] fault >> addr 2055ae000, iommu reg = ffff82c3fff57000 >> (XEN) DMAR:[fault reason 02h] Present bit in context entry is clear >> (XEN) print_vtd_entries: iommu = ffff83013fffaee0 bdf = 5:8.0 gmfn >> 2055ae >> (XEN) root_entry = ffff83013ff37000 >> (XEN) root_entry[5] = 13cf12001 >> (XEN) context = ffff83013cf12000 >> (XEN) context[40] = 0_0 >> (XEN) ctxt_entry[40] not present >> (XEN) [VT-D]iommu.c:821: iommu_fault_status: Primary Pending Fault >> (XEN) [VT-D]iommu.c:796: DMAR:[DMA Write] Request device [05:08.0] fault >> addr 205544000, iommu reg = ffff82c3fff57000 >> (XEN) DMAR:[fault reason 02h] Present bit in context entry is clear >> (XEN) print_vtd_entries: iommu = ffff83013fffaee0 bdf = 5:8.0 gmfn >> 205544 >> (XEN) root_entry = ffff83013ff37000 >> (XEN) root_entry[5] = 13cf12001 >> (XEN) context = ffff83013cf12000 >> (XEN) context[40] = 0_0 >> (XEN) ctxt_entry[40] not present >> (XEN) [VT-D]iommu.c:796: DMAR:[DMA Write] Request device [05:08.0] fault >> addr 204865000, iommu reg = ffff82c3fff57000 >> (XEN) DMAR:[fault reason 02h] Present bit in context entry is clear >> (XEN) print_vtd_entries: iommu = ffff83013fffaee0 bdf = 5:8.0 gmfn >> 204865 >> (XEN) root_entry = ffff83013ff37000 >> (XEN) root_entry[5] = 13cf12001 >> (XEN) context = ffff83013cf12000 >> (XEN) context[40] = 0_0 >> (XEN) ctxt_entry[40] not present >> (XEN) [VT-D]iommu.c:821: iommu_fault_status: Primary Pending Fault >> (XEN) [VT-D]iommu.c:796: DMAR:[DMA Write] Request device [05:08.0] fault >> addr 2074be000, iommu reg = ffff82c3fff57000 >> (XEN) DMAR:[fault reason 02h] Present bit in context entry is clear >> (XEN) print_vtd_entries: iommu = ffff83013fffaee0 bdf = 5:8.0 gmfn >> 2074be >> (XEN) root_entry = ffff83013ff37000 >> (XEN) root_entry[5] = 13cf12001 >> (XEN) context = ffff83013cf12000 >> (XEN) context[40] = 0_0 >> (XEN) ctxt_entry[40] not present >> >> (XEN) [VT-D]iommu.c:796: DMAR:[DMA Write] Request device [05:08.0] fault >> addr 204865000, iommu reg = ffff82c3fff57000 >> (XEN) DMAR:[fault reason 02h] Present bit in context entry is clear >> (XEN) print_vtd_entries: iommu = ffff83013fffaee0 bdf = 5:8.0 gmfn >> 204865 >> (XEN) root_entry = ffff83013ff37000 >> (XEN) root_entry[5] = 13cf12001 >> (XEN) context = ffff83013cf12000 >> (XEN) context[40] = 0_0 >> (XEN) ctxt_entry[40] not present >> (XEN) [VT-D]iommu.c:821: iommu_fault_status: Primary Pending Fault >> (XEN) [VT-D]iommu.c:796: DMAR:[DMA Write] Request device [05:08.0] fault >> addr 2074be000, iommu reg = ffff82c3fff57000 >> (XEN) DMAR:[fault reason 02h] Present bit in context entry is clear >> (XEN) print_vtd_entries: iommu = ffff83013fffaee0 bdf = 5:8.0 gmfn >> 2074be >> (XEN) root_entry = ffff83013ff37000 >> (XEN) root_entry[5] = 13cf12001 >> (XEN) context = ffff83013cf12000 >> (XEN) context[40] = 0_0 >> (XEN) ctxt_entry[40] not present >> >> (XEN) [VT-D]iommu.c:796: DMAR:[DMA Write] Request device [05:08.0] fault >> addr 204865000, iommu reg = ffff82c3fff57000 >> (XEN) DMAR:[fault reason 02h] Present bit in context entry is clear >> (XEN) print_vtd_entries: iommu = ffff83013fffaee0 bdf = 5:8.0 gmfn >> 204865 >> (XEN) root_entry = ffff83013ff37000 >> (XEN) root_entry[5] = 13cf12001 >> (XEN) context = ffff83013cf12000 >> (XEN) context[40] = 0_0 >> (XEN) ctxt_entry[40] not present >> (XEN) [VT-D]iommu.c:821: iommu_fault_status: Primary Pending Fault >> (XEN) [VT-D]iommu.c:796: DMAR:[DMA Write] Request device [05:08.0] fault >> addr 2074be000, iommu reg = ffff82c3fff57000 >> (XEN) DMAR:[fault reason 02h] Present bit in context entry is clear >> (XEN) print_vtd_entries: iommu = ffff83013fffaee0 bdf = 5:8.0 gmfn >> 2074be >> (XEN) root_entry = ffff83013ff37000 >> (XEN) root_entry[5] = 13cf12001 >> (XEN) context = ffff83013cf12000 >> (XEN) context[40] = 0_0 >> (XEN) ctxt_entry[40] not present >> >> (XEN) [VT-D]iommu.c:796: DMAR:[DMA Write] Request device [05:08.0] fault >> addr 204865000, iommu reg = ffff82c3fff57000 >> (XEN) DMAR:[fault reason 02h] Present bit in context entry is clear >> (XEN) print_vtd_entries: iommu = ffff83013fffaee0 bdf = 5:8.0 gmfn >> 204865 >> (XEN) root_entry = ffff83013ff37000 >> (XEN) root_entry[5] = 13cf12001 >> (XEN) context = ffff83013cf12000 >> (XEN) context[40] = 0_0 >> (XEN) ctxt_entry[40] not present >> (XEN) [VT-D]iommu.c:821: iommu_fault_status: Primary Pending Fault >> (XEN) [VT-D]iommu.c:796: DMAR:[DMA Write] Request device [05:08.0] fault >> addr 2074be000, iommu reg = ffff82c3fff57000 >> (XEN) DMAR:[fault reason 02h] Present bit in context entry is clear >> (XEN) print_vtd_entries: iommu = ffff83013fffaee0 bdf = 5:8.0 gmfn >> 2074be >> (XEN) root_entry = ffff83013ff37000 >> (XEN) root_entry[5] = 13cf12001 >> (XEN) context = ffff83013cf12000 >> (XEN) context[40] = 0_0 >> (XEN) ctxt_entry[40] not present >> >> (XEN) [VT-D]iommu.c:796: DMAR:[DMA Write] Request device [05:08.0] fault >> addr 204865000, iommu reg = ffff82c3fff57000 >> (XEN) DMAR:[fault reason 02h] Present bit in context entry is clear >> (XEN) print_vtd_entries: iommu = ffff83013fffaee0 bdf = 5:8.0 gmfn >> 204865 >> (XEN) root_entry = ffff83013ff37000 >> (XEN) root_entry[5] = 13cf12001 >> (XEN) context = ffff83013cf12000 >> (XEN) context[40] = 0_0 >> (XEN) ctxt_entry[40] not present >> (XEN) [VT-D]iommu.c:821: iommu_fault_status: Primary Pending Fault >> (XEN) [VT-D]iommu.c:796: DMAR:[DMA Write] Request device [05:08.0] fault >> addr 2074be000, iommu reg = ffff82c3fff57000 >> (XEN) DMAR:[fault reason 02h] Present bit in context entry is clear >> (XEN) print_vtd_entries: iommu = ffff83013fffaee0 bdf = 5:8.0 gmfn >> 2074be >> (XEN) root_entry = ffff83013ff37000 >> (XEN) root_entry[5] = 13cf12001 >> (XEN) context = ffff83013cf12000 >> (XEN) context[40] = 0_0 >> (XEN) ctxt_entry[40] not present >> >> (XEN) [VT-D]iommu.c:796: DMAR:[DMA Write] Request device [05:08.0] fault >> addr 204865000, iommu reg = ffff82c3fff57000 >> (XEN) DMAR:[fault reason 02h] Present bit in context entry is clear >> (XEN) print_vtd_entries: iommu = ffff83013fffaee0 bdf = 5:8.0 gmfn >> 204865 >> (XEN) root_entry = ffff83013ff37000 >> (XEN) root_entry[5] = 13cf12001 >> (XEN) context = ffff83013cf12000 >> (XEN) context[40] = 0_0 >> (XEN) ctxt_entry[40] not present >> (XEN) [VT-D]iommu.c:821: iommu_fault_status: Primary Pending Fault >> (XEN) [VT-D]iommu.c:796: DMAR:[DMA Write] Request device [05:08.0] fault >> addr 2074be000, iommu reg = ffff82c3fff57000 >> (XEN) DMAR:[fault reason 02h] Present bit in context entry is clear >> (XEN) print_vtd_entries: iommu = ffff83013fffaee0 bdf = 5:8.0 gmfn >> 2074be >> (XEN) root_entry = ffff83013ff37000 >> (XEN) root_entry[5] = 13cf12001 >> (XEN) context = ffff83013cf12000 >> (XEN) context[40] = 0_0 >> (XEN) ctxt_entry[40] not present >> >> (XEN) [VT-D]iommu.c:796: DMAR:[DMA Write] Request device [05:08.0] fault >> addr 204865000, iommu reg = ffff82c3fff57000 >> (XEN) DMAR:[fault reason 02h] Present bit in context entry is clear >> (XEN) print_vtd_entries: iommu = ffff83013fffaee0 bdf = 5:8.0 gmfn >> 204865 >> (XEN) root_entry = ffff83013ff37000 >> (XEN) root_entry[5] = 13cf12001 >> (XEN) context = ffff83013cf12000 >> (XEN) context[40] = 0_0 >> (XEN) ctxt_entry[40] not present >> (XEN) [VT-D]iommu.c:821: iommu_fault_status: Primary Pending Fault >> (XEN) [VT-D]iommu.c:796: DMAR:[DMA Write] Request device [05:08.0] fault >> addr 2074be000, iommu reg = ffff82c3fff57000 >> (XEN) DMAR:[fault reason 02h] Present bit in context entry is clear >> (XEN) print_vtd_entries: iommu = ffff83013fffaee0 bdf = 5:8.0 gmfn >> 2074be >> (XEN) root_entry = ffff83013ff37000 >> (XEN) root_entry[5] = 13cf12001 >> (XEN) context = ffff83013cf12000 >> (XEN) context[40] = 0_0 >> (XEN) ctxt_entry[40] not present >> >> (XEN) context[40] = 0_0 >> (XEN) ctxt_entry[40] not present >> (XEN) [VT-D]iommu.c:796: DMAR:[DMA Write] Request device [05:08.0] fault >> addr 204865000, iommu reg = ffff82c3fff57000 >> (XEN) DMAR:[fault reason 02h] Present bit in context entry is clear >> (XEN) print_vtd_entries: iommu = ffff83013fffaee0 bdf = 5:8.0 gmfn >> 204865 >> (XEN) root_entry = ffff83013ff37000 >> (XEN) root_entry[5] = 13cf12001 >> (XEN) context = ffff83013cf12000 >> (XEN) context[40] = 0_0 >> (XEN) ctxt_entry[40] not present >> (XEN) [VT-D]iommu.c:821: iommu_fault_status: Primary Pending Fault >> (XEN) [VT-D]iommu.c:796: DMAR:[DMA Write] Request device [05:08.0] fault >> addr 2074be000, iommu reg = ffff82c3fff57000 >> (XEN) DMAR:[fault reason 02h] Present bit in context entry is clear >> (XEN) print_vtd_entries: iommu = ffff83013fffaee0 bdf = 5:8.0 gmfn >> 2074be >> (XEN) root_entry = ffff83013ff37000 >> (XEN) root_entry[5] = 13cf12001 >> (XEN) context = ffff83013cf12000 >> (XEN) context[40] = 0_0 >> (XEN) ctxt_entry[40] not present >> >> (XEN) context[40] = 0_0 >> (XEN) ctxt_entry[40] not present >> (XEN) [VT-D]iommu.c:796: DMAR:[DMA Write] Request device [05:08.0] fault >> addr 204865000, iommu reg = ffff82c3fff57000 >> (XEN) DMAR:[fault reason 02h] Present bit in context entry is clear >> (XEN) print_vtd_entries: iommu = ffff83013fffaee0 bdf = 5:8.0 gmfn >> 204865 >> (XEN) root_entry = ffff83013ff37000 >> (XEN) root_entry[5] = 13cf12001 >> (XEN) context = ffff83013cf12000 >> (XEN) context[40] = 0_0 >> (XEN) ctxt_entry[40] not present >> (XEN) [VT-D]iommu.c:821: iommu_fault_status: Primary Pending Fault >> (XEN) [VT-D]iommu.c:796: DMAR:[DMA Write] Request device [05:08.0] fault >> addr 2074be000, iommu reg = ffff82c3fff57000 >> (XEN) DMAR:[fault reason 02h] Present bit in context entry is clear >> (XEN) print_vtd_entries: iommu = ffff83013fffaee0 bdf = 5:8.0 gmfn >> 2074be >> (XEN) root_entry = ffff83013ff37000 >> (XEN) root_entry[5] = 13cf12001 >> (XEN) context = ffff83013cf12000 >> (XEN) context[40] = 0_0 >> (XEN) ctxt_entry[40] not present >> >> (XEN) context[40] = 0_0 >> (XEN) ctxt_entry[40] not present >> (XEN) [VT-D]iommu.c:796: DMAR:[DMA Write] Request device [05:08.0] fault >> addr 204865000, iommu reg = ffff82c3fff57000 >> (XEN) DMAR:[fault reason 02h] Present bit in context entry is clear >> (XEN) print_vtd_entries: iommu = ffff83013fffaee0 bdf = 5:8.0 gmfn >> 204865 >> (XEN) root_entry = ffff83013ff37000 >> (XEN) root_entry[5] = 13cf12001 >> (XEN) context = ffff83013cf12000 >> (XEN) context[40] = 0_0 >> (XEN) ctxt_entry[40] not present >> (XEN) [VT-D]iommu.c:821: iommu_fault_status: Primary Pending Fault >> (XEN) [VT-D]iommu.c:796: DMAR:[DMA Write] Request device [05:08.0] fault >> addr 2074be000, iommu reg = ffff82c3fff57000 >> (XEN) DMAR:[fault reason 02h] Present bit in context entry is clear >> (XEN) print_vtd_entries: iommu = ffff83013fffaee0 bdf = 5:8.0 gmfn >> 2074be >> (XEN) root_entry = ffff83013ff37000 >> (XEN) root_entry[5] = 13cf12001 >> (XEN) context = ffff83013cf12000 >> (XEN) context[40] = 0_0 >> (XEN) ctxt_entry[40] not present >> >> (XEN) context[40] = 0_0 >> (XEN) ctxt_entry[40] not present >> (XEN) [VT-D]iommu.c:796: DMAR:[DMA Write] Request device [05:08.0] fault >> addr 204865000, iommu reg = ffff82c3fff57000 >> (XEN) DMAR:[fault reason 02h] Present bit in context entry is clear >> (XEN) print_vtd_entries: iommu = ffff83013fffaee0 bdf = 5:8.0 gmfn >> 204865 >> (XEN) root_entry = ffff83013ff37000 >> (XEN) root_entry[5] = 13cf12001 >> (XEN) context = ffff83013cf12000 >> (XEN) context[40] = 0_0 >> (XEN) ctxt_entry[40] not present >> (XEN) [VT-D]iommu.c:821: iommu_fault_status: Primary Pending Fault >> (XEN) [VT-D]iommu.c:796: DMAR:[DMA Write] Request device [05:08.0] fault >> addr 2074be000, iommu reg = ffff82c3fff57000 >> (XEN) DMAR:[fault reason 02h] Present bit in context entry is clear >> (XEN) print_vtd_entries: iommu = ffff83013fffaee0 bdf = 5:8.0 gmfn >> 2074be >> (XEN) root_entry = ffff83013ff37000 >> (XEN) root_entry[5] = 13cf12001 >> (XEN) context = ffff83013cf12000 >> (XEN) context[40] = 0_0 >> (XEN) ctxt_entry[40] not present >> >> >> _______________________________________________ >> Xen-devel mailing list >> Xen-devel@lists.xensource.com >> http://lists.xensource.com/xen-devel >> > > > _______________________________________________ > Xen-devel mailing list > Xen-devel@lists.xensource.com > http://lists.xensource.com/xen-devel_______________________________________________ Xen-devel mailing list Xen-devel@lists.xensource.com http://lists.xensource.com/xen-devel
Weidong Han
2010-Jun-02 07:05 UTC
Re: [Xen-devel] iommuu/vt-d issues with LSI MegaSAS (PERC5i)
Pasi Kärkkäinen wrote:> On Wed, Jun 02, 2010 at 09:23:37AM +0800, Weidong Han wrote: > >> This PCI-x card is not suitable for assignment. It contains an invisible >> device 05:08.0 (lspci cannot show it), but this invisible device won''t >> be mapped by VT-d because VT-d engine doesn''t know this device, so you >> can see the DMAR faults on it. One workaround is to hard code to map >> 05:08.0 when assign 05:0e.0. BTW, PCIe LSI card don''t have this problem. >> >> > > Note that this problem happens when booting up dom0.. >I see. all devices are assigned to dom0 in booting. It just needs to map 05:08.0 as well when map 05:0e.0 in domain_context_mapping. Regards, Weidong> -- Pasi > > >> Regards, >> Weidong >> >> M. Nunberg wrote: >> >>> I''ve been trying to get VT-D working wiht xen for quite some time, since >>> 3.4.2, and I''ve always had issues with my RAID controller not working >>> properly when iommu is not disabled in Xen: >>> >>> lspci outpuut for the card: >>> 05:0e.0 RAID bus controller: Dell PowerEdge Expandable RAID controller 5 >>> Subsystem: Dell PERC 5/i Integrated RAID Controller >>> Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- >>> Stepping+ SERR- FastB2B- DisINTx- >>> Status: Cap+ 66MHz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- >>> <TAbort- <MAbort- >SERR- <PERR- INTx- >>> Latency: 64 (32000ns min), Cache Line Size: 64 bytes >>> Interrupt: pin A routed to IRQ 18 >>> Region 0: Memory at f2ff0000 (32-bit, prefetchable) [size=64K] >>> Region 2: Memory at fbce0000 (32-bit, non-prefetchable) [size=128K] >>> Expansion ROM at fbcd0000 [disabled] [size=32K] >>> Capabilities: [c0] Power Management version 2 >>> Flags: PMEClk- DSI- D1+ D2- AuxCurrent=0mA >>> PME(D0-,D1-,D2-,D3hot-,D3cold-) >>> Status: D0 PME-Enable- DSel=0 DScale=0 PME- >>> Capabilities: [d0] Message Signalled Interrupts: Mask- 64bit+ Queue=0/1 >>> Enable- >>> Address: 0000000000000000 Data: 0000 >>> Capabilities: [e0] PCI-X non-bridge device >>> Command: DPERE- ERO- RBC=512 OST=4 >>> Status: Dev=05:0e.0 64bit+ 133MHz+ SCD- USC- DC=bridge DMMRBC=1024 >>> DMOST=4 DMCRS=16 RSCEM- 266MHz- 533MHz- >>> Kernel driver in use: megaraid_sas >>> Kernel modules: megaraid_sas >>> >>> I am using a Supermicro X8DALi motherboard with a 5500 chipset. >>> >>> Whenever I try to access the device the Xen console spits out something >>> like this: >>> (XEN) [VT-D]iommu.c:796: DMAR:[DMA Write] Request device [05:08.0] fault >>> addr 204865000, iommu reg = ffff82c3fff57000 >>> (XEN) DMAR:[fault reason 02h] Present bit in context entry is clear >>> (XEN) print_vtd_entries: iommu = ffff83013fffaee0 bdf = 5:8.0 gmfn >>> 204865 >>> (XEN) root_entry = ffff83013ff37000 >>> (XEN) root_entry[5] = 13cf12001 >>> (XEN) context = ffff83013cf12000 >>> (XEN) context[40] = 0_0 >>> (XEN) ctxt_entry[40] not present >>> (XEN) [VT-D]iommu.c:821: iommu_fault_status: Primary Pending Fault >>> >>> reads are partially succcessful, but I am getting seek errors at times, >>> filesystems will mount properly but I cannot use any of them properly.. >>> >>> >>> The actual kernel output varies, sometimes i get EINVAL when I try to >>> read from the filesystem, sometimes it simply refuses to at all >>> recognize the disk altogether, and other times it will hang the entire >>> system, including the hypervisor itself. >>> I''ve tried booting the hypervisor with x2apic disabled, but to no >>> effect. I''ve also tried with the latest xen-4.0-testing (4.0.1), buut >>> same issue and same outpuut >>> >>> A quick google turns up a thread, from this mailing list, with a >>> different RAID card, but the kernel output is similar.. e.g. >>> >>> scsi scan: INQUIRY result too short (5), using 36 >>> >>> http://lists.xensource.com/archives/html/xen-users/2010-04/msg00535.html >>> >>> The full xen log is below >>> >>> >>> >>> L __ __ _ _ ___ >>> ___ >>> \ \/ /___ _ __ | || | / _ \ / _ \ 0x146000>, shtab=0x3a2078, >>> entry=0x100000 >>> \ // _ \ ''_ \ | || |_| | | | | | >>> | >>> / \ __/ | | | |__ _| |_| | |_| |apper/OS-root ro nomodeset >>> console=tty0 r >>> /_/\_\___|_| |_| | >>> _|(_)___(_)___/ >>> 020 >>> bytes] >>> (XEN) Xen version 4.0.0 (mordy@) (gcc version 4.3.2 (Debian 4.3.2-1.1) ) >>> Fri May 21 07:50:16 PDT 2010boot-module >>> @ >>> (XEN) Latest ChangeSet: >>> unavailable >>> (XEN) Console output is >>> synchronous. >>> (XEN) Command line: iommu=verbose loglvl=all guest_loglvl=all >>> sync_console console_to_rint com1=115200,8n1 >>> console=com1 >>> (XEN) Video >>> information: >>> (XEN) VGA is text mode 80x25, font >>> 8x16 >>> (XEN) VBE/DDC methods: none; EDID transfer time: 0 >>> seconds >>> (XEN) EDID info not retrieved because no DDC retrieval method >>> detected >>> (XEN) Disc information: >>> (XEN) Found 1 MBR signatures >>> (XEN) Found 1 EDD information structures >>> (XEN) Xen-e820 RAM map: >>> (XEN) 0000000000000000 - 000000000009a000 (usable) >>> (XEN) 000000000009a000 - 00000000000a0000 (reserved) >>> (XEN) 00000000000e0000 - 0000000000100000 (reserved) >>> (XEN) 0000000000100000 - 00000000bf760000 (usable) >>> (XEN) 00000000bf76e000 - 00000000bf770000 type 9 >>> (XEN) 00000000bf770000 - 00000000bf77e000 (ACPI data) >>> (XEN) 00000000bf77e000 - 00000000bf7d0000 (ACPI NVS) >>> (XEN) 00000000bf7d0000 - 00000000bf7e0000 (reserved) >>> (XEN) 00000000bf7ec000 - 00000000c0000000 (reserved) >>> (XEN) 00000000fee00000 - 00000000fee01000 (reserved) >>> (XEN) 00000000ffc00000 - 0000000100000000 (reserved) >>> (XEN) 0000000100000000 - 0000000340000000 (usable) >>> (XEN) ACPI: RSDP 000F9E10, 0024 (r2 ACPIAM) >>> (XEN) ACPI: XSDT BF770100, 0094 (r1 NEC 20090424 MSFT >>> 97) >>> (XEN) ACPI: FACP BF770290, 00F4 (r4 042409 FACP1917 20090424 MSFT >>> 97) >>> (XEN) ACPI: DSDT BF770670, 5BFB (r2 10601 10601000 0 INTL >>> 20051117) >>> (XEN) ACPI: FACS BF77E000, 0040 >>> (XEN) ACPI: APIC BF770390, 00D2 (r2 042409 APIC1917 20090424 MSFT >>> 97) >>> (XEN) ACPI: MCFG BF770470, 003C (r1 042409 OEMMCFG 20090424 MSFT >>> 97) >>> (XEN) ACPI: SLIC BF7704B0, 0176 (r1 NEC 20090424 MSFT >>> 97) >>> (XEN) ACPI: ERST BF770630, 0040 (r1 042409 WHEA1917 20090424 MSFT >>> 97) >>> (XEN) ACPI: OEMB BF77E040, 007B (r1 042409 OEMB1917 20090424 MSFT >>> 97) >>> (XEN) ACPI: SRAT BF77A670, 01D0 (r1 042409 OEMSRAT 1 INTL >>> 1) >>> (XEN) ACPI: HPET BF77A840, 0038 (r1 042409 OEMHPET 20090424 MSFT >>> 97) >>> (XEN) ACPI: DMAR BF77E0C0, 0118 (r1 AMI OEMDMAR 1 MSFT >>> 97) >>> (XEN) ACPI: SSDT BF781DF0, 0363 (r1 DpgPmm CpuPm 12 INTL >>> 20051117) >>> (XEN) ACPI: EINJ BF77A880, 0130 (r1 AMIER AMI_EINJ 20090424 MSFT >>> 97) >>> (XEN) ACPI: BERT BF77AA10, 0030 (r1 AMIER AMI_BERT 20090424 MSFT >>> 97) >>> (XEN) ACPI: ERST BF77AA40, 01B0 (r1 AMIER AMI_ERST 20090424 MSFT >>> 97) >>> (XEN) ACPI: HEST BF77ABF0, 00A8 (r1 AMIER AMI_HEST 20090424 MSFT >>> 97) >>> (XEN) System RAM: 12045MB (12334808kB) >>> (XEN) SRAT: PXM 0 -> APIC 0 -> Node 0 >>> (XEN) SRAT: PXM 0 -> APIC 2 -> Node 0 >>> (XEN) SRAT: PXM 0 -> APIC 4 -> Node 0 >>> (XEN) SRAT: PXM 0 -> APIC 6 -> Node 0 >>> (XEN) SRAT: PXM 0 -> APIC 1 -> Node 0 >>> (XEN) SRAT: PXM 0 -> APIC 3 -> Node 0 >>> (XEN) SRAT: PXM 0 -> APIC 5 -> Node 0 >>> (XEN) SRAT: PXM 0 -> APIC 7 -> Node 0 >>> (XEN) SRAT: PXM 1 -> APIC 16 -> Node 1 >>> (XEN) SRAT: PXM 1 -> APIC 18 -> Node 1 >>> (XEN) SRAT: PXM 1 -> APIC 20 -> Node 1 >>> (XEN) SRAT: PXM 1 -> APIC 22 -> Node 1 >>> (XEN) SRAT: PXM 1 -> APIC 17 -> Node 1 >>> (XEN) SRAT: PXM 1 -> APIC 19 -> Node 1 >>> (XEN) SRAT: PXM 1 -> APIC 21 -> Node 1 >>> (XEN) SRAT: PXM 1 -> APIC 23 -> Node 1 >>> (XEN) SRAT: Node 0 PXM 0 0-a0000 >>> (XEN) SRAT: Node 0 PXM 0 100000-c0000000 >>> (XEN) SRAT: Node 0 PXM 0 100000000-1c0000000 >>> (XEN) SRAT: Node 1 PXM 1 1c0000000-340000000 >>> (XEN) NUMA: Allocated memnodemap from 33fdfb000 - 33fdff000 >>> (XEN) NUMA: Using 8 for the hash shift. >>> (XEN) Domain heap initialised DMA width 30 bits >>> (XEN) found SMP MP-table at 000ff780 >>> (XEN) DMI present. >>> (XEN) Using APIC driver default >>> (XEN) ACPI: PM-Timer IO Port: 0x808 >>> (XEN) ACPI: ACPI SLEEP INFO: pm1x_cnt[804,0], pm1x_evt[800,0] >>> (XEN) ACPI: wakeup_vec[bf77e00c], vec_size[20] >>> (XEN) ACPI: Local APIC address 0xfee00000 >>> (XEN) ACPI: LAPIC (acpi_id[0x01] lapic_id[0x00] enabled) >>> (XEN) Processor #0 7:10 APIC version 21 >>> (XEN) ACPI: LAPIC (acpi_id[0x02] lapic_id[0x10] enabled) >>> (XEN) Processor #16 7:10 APIC version 21 >>> (XEN) ACPI: LAPIC (acpi_id[0x03] lapic_id[0x02] enabled) >>> (XEN) Processor #2 7:10 APIC version 21 >>> (XEN) ACPI: LAPIC (acpi_id[0x04] lapic_id[0x12] enabled) >>> (XEN) Processor #18 7:10 APIC version 21 >>> (XEN) ACPI: LAPIC (acpi_id[0x05] lapic_id[0x04] enabled) >>> (XEN) Processor #4 7:10 APIC version 21 >>> (XEN) ACPI: LAPIC (acpi_id[0x06] lapic_id[0x14] enabled) >>> (XEN) Processor #20 7:10 APIC version 21 >>> (XEN) ACPI: LAPIC (acpi_id[0x07] lapic_id[0x06] enabled) >>> (XEN) Processor #6 7:10 APIC version 21 >>> (XEN) ACPI: LAPIC (acpi_id[0x08] lapic_id[0x16] enabled) >>> (XEN) Processor #22 7:10 APIC version 21 >>> (XEN) ACPI: LAPIC (acpi_id[0x09] lapic_id[0x01] enabled) >>> (XEN) Processor #1 7:10 APIC version 21 >>> (XEN) ACPI: LAPIC (acpi_id[0x0a] lapic_id[0x11] enabled) >>> (XEN) Processor #17 7:10 APIC version 21 >>> (XEN) ACPI: LAPIC (acpi_id[0x0b] lapic_id[0x03] enabled) >>> (XEN) Processor #3 7:10 APIC version 21 >>> (XEN) ACPI: LAPIC (acpi_id[0x0c] lapic_id[0x13] enabled) >>> (XEN) Processor #19 7:10 APIC version 21 >>> (XEN) ACPI: LAPIC (acpi_id[0x0d] lapic_id[0x05] enabled) >>> (XEN) Processor #5 7:10 APIC version 21 >>> (XEN) ACPI: LAPIC (acpi_id[0x0e] lapic_id[0x15] enabled) >>> (XEN) Processor #21 7:10 APIC version 21 >>> (XEN) ACPI: LAPIC (acpi_id[0x0f] lapic_id[0x07] enabled) >>> (XEN) Processor #7 7:10 APIC version 21 >>> (XEN) ACPI: LAPIC (acpi_id[0x10] lapic_id[0x17] enabled) >>> (XEN) Processor #23 7:10 APIC version 21 >>> (XEN) ACPI: LAPIC_NMI (acpi_id[0xff] dfl dfl lint[0x1]) >>> (XEN) Overriding APIC driver with bigsmp >>> (XEN) ACPI: IOAPIC (id[0x08] address[0xfec00000] gsi_base[0]) >>> (XEN) IOAPIC[0]: apic_id 8, version 32, address 0xfec00000, GSI 0-23 >>> (XEN) ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl) >>> (XEN) ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 20 low level) >>> (XEN) ACPI: IRQ0 used by override. >>> (XEN) ACPI: IRQ2 used by override. >>> (XEN) ACPI: IRQ9 used by override. >>> (XEN) Enabling APIC mode: Phys. Using 1 I/O APICs >>> (XEN) ACPI: HPET id: 0xffffffff base: 0xfed00000 >>> (XEN) [VT-D]dmar.c:679: Host address width 40 >>> (XEN) [VT-D]dmar.c:694: found ACPI_DMAR_DRHD: >>> (XEN) [VT-D]dmar.c:398: dmaru->address = fbffe000 >>> (XEN) [VT-D]dmar.c:340: IOAPIC: f0:1f.7 >>> (XEN) [VT-D]dmar.c:411: flags: INCLUDE_ALL >>> (XEN) [VT-D]dmar.c:699: found ACPI_DMAR_RMRR: >>> (XEN) [VT-D]dmar.c:334: endpoint: 0:1d.0 >>> (XEN) [VT-D]dmar.c:334: endpoint: 0:1d.1 >>> (XEN) [VT-D]dmar.c:334: endpoint: 0:1d.2 >>> (XEN) [VT-D]dmar.c:334: endpoint: 0:1d.7 >>> (XEN) [VT-D]dmar.c:334: endpoint: 0:1a.0 >>> (XEN) [VT-D]dmar.c:334: endpoint: 0:1a.1 >>> (XEN) [VT-D]dmar.c:334: endpoint: 0:1a.2 >>> (XEN) [VT-D]dmar.c:334: endpoint: 0:1a.7 >>> (XEN) [VT-D]dmar.c:571: RMRR region: base_addr ec000 end_address effff >>> (XEN) [VT-D]dmar.c:699: found ACPI_DMAR_RMRR: >>> (XEN) [VT-D]dmar.c:334: endpoint: 0:1d.0 >>> (XEN) [VT-D]dmar.c:334: endpoint: 0:1d.1 >>> (XEN) [VT-D]dmar.c:334: endpoint: 0:1d.2 >>> (XEN) [VT-D]dmar.c:334: endpoint: 0:1d.7 >>> (XEN) [VT-D]dmar.c:334: endpoint: 0:1a.0 >>> (XEN) [VT-D]dmar.c:334: endpoint: 0:1a.1 >>> (XEN) [VT-D]dmar.c:334: endpoint: 0:1a.2 >>> (XEN) [VT-D]dmar.c:334: endpoint: 0:1a.7 >>> (XEN) [VT-D]dmar.c:571: RMRR region: base_addr bf7ec000 end_address >>> bf7fffff >>> (XEN) [VT-D]dmar.c:704: found ACPI_DMAR_ATSR: >>> (XEN) [VT-D]dmar.c:599: atsru->all_ports: 0 >>> (XEN) [VT-D]dmar.c:320: bridge: 0:1.0 start = 0 sec = 1 sub = 1 >>> (XEN) [VT-D]dmar.c:320: bridge: 0:3.0 start = 0 sec = 2 sub = 2 >>> (XEN) [VT-D]dmar.c:320: bridge: 0:7.0 start = 0 sec = 3 sub = 3 >>> (XEN) PCI: MCFG configuration 0: base e0000000 segment 0 buses 0 - 255 >>> (XEN) PCI: Not using MMCONFIG. >>> (XEN) Using ACPI (MADT) for SMP configuration information >>> (XEN) Using scheduler: SMP Credit Scheduler (credit) >>> (XEN) Detected 2266.790 MHz processor. >>> (XEN) Initing memory sharing. >>> (XEN) VMX: Supported advanced features: >>> (XEN) - APIC MMIO access virtualisation >>> (XEN) - APIC TPR shadow >>> (XEN) - Extended Page Tables (EPT) >>> (XEN) - Virtual-Processor Identifiers (VPID) >>> (XEN) - Virtual NMI >>> (XEN) - MSR direct-access bitmap >>> (XEN) HVM: ASIDs enabled. >>> (XEN) HVM: VMX enabled >>> (XEN) HVM: Hardware Assisted Paging detected. >>> (XEN) Intel machine check reporting enabled >>> (XEN) [VT-D]iommu.c:1078: drhd->address = fbffe000 iommu->reg >>> ffff82c3fff57000 >>> (XEN) [VT-D]iommu.c:1080: cap = c90780106f0462 ecap = f0207e >>> (XEN) Intel VT-d Snoop Control not supported. >>> (XEN) Intel VT-d DMA Passthrough not supported. >>> (XEN) Intel VT-d Queued Invalidation supported. >>> (XEN) Intel VT-d Interrupt Remapping supported. >>> (XEN) I/O virtualisation enabled >>> (XEN) I/O virtualisation for PV guests disabled >>> (XEN) Total of 16 processors activated. >>> (XEN) ENABLING IO-APIC IRQs >>> (XEN) -> Using new ACK method >>> (XEN) ..TIMER: vector=0xF0 apic1=0 pin1=2 apic2=-1 pin2=-1 >>> (XEN) TSC is reliable, synchronization unnecessary >>> (XEN) Platform timer is 14.318MHz HPET >>> ?(XEN) Allocated console ring of 128 KiB. >>> (XEN) microcode.c:73:d32767 microcode: CPU1 resumed >>> (XEN) microcode.c:73:d32767 microcode: CPU9 resumed >>> (XEN) microcode.c:73:d32767 microcode: CPU14 resumed >>> (XEN) microcode.c:73:d32767 microcode: CPU6 resumed >>> (XEN) microcode.c:73:d32767 microcode: CPU3 resumed >>> (XEN) microcode.c:73:d32767 microcode: CPU11 resumed >>> (XEN) microcode.c:73:d32767 microcode: CPU8 resumed >>> (XEN) microcode.c:73:d32767 microcode: CPU7 resumed >>> (XEN) microcode.c:73:d32767 microcode: CPU15 resumed >>> (XEN) microcode.c:73:d32767 microcode: CPU2 resumed >>> (XEN) microcode.c:73:d32767 microcode: CPU5 resumed >>> (XEN) microcode.c:73:d32767 microcode: CPU13 resumed >>> (XEN) microcode.c:73:d32767 microcode: CPU4 resumed >>> (XEN) microcode.c:73:d32767 microcode: CPU10 resumed >>> (XEN) Brought up 16 CPUs >>> (XEN) microcode.c:73:d32767 microcode: CPU12 resumed >>> (XEN) Turbo Mode detected! >>> (XEN) HPET''s MSI mode hasn''t been supported when Interrupt Remapping is >>> enabled. >>> (XEN) ACPI sleep modes: S3 >>> (XEN) mcheck_poll: Machine check polling timer started. >>> (XEN) [VT-D]iommu.c:1325: d0:PCIe: map bdf = 0:0.0 >>> (XEN) [VT-D]iommu.c:1325: d0:PCIe: map bdf = 0:14.0 >>> (XEN) [VT-D]iommu.c:1325: d0:PCIe: map bdf = 0:14.1 >>> (XEN) [VT-D]iommu.c:1325: d0:PCIe: map bdf = 0:14.2 >>> (XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = 0:14.3 >>> (XEN) [VT-D]iommu.c:1325: d0:PCIe: map bdf = 0:16.0 >>> (XEN) [VT-D]iommu.c:1325: d0:PCIe: map bdf = 0:16.1 >>> (XEN) [VT-D]iommu.c:1325: d0:PCIe: map bdf = 0:16.2 >>> (XEN) [VT-D]iommu.c:1325: d0:PCIe: map bdf = 0:16.3 >>> (XEN) [VT-D]iommu.c:1325: d0:PCIe: map bdf = 0:16.4 >>> (XEN) [VT-D]iommu.c:1325: d0:PCIe: map bdf = 0:16.5 >>> (XEN) [VT-D]iommu.c:1325: d0:PCIe: map bdf = 0:16.6 >>> (XEN) [VT-D]iommu.c:1325: d0:PCIe: map bdf = 0:16.7 >>> (XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = 0:1a.0 >>> (XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = 0:1a.1 >>> (XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = 0:1a.2 >>> (XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = 0:1a.7 >>> (XEN) [VT-D]iommu.c:1325: d0:PCIe: map bdf = 0:1b.0 >>> (XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = 0:1d.0 >>> (XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = 0:1d.1 >>> (XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = 0:1d.2 >>> (XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = 0:1d.7 >>> (XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = 0:1f.0 >>> (XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = 0:1f.2 >>> (XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = 0:1f.3 >>> (XEN) [VT-D]iommu.c:1325: d0:PCIe: map bdf = 1:0.0 >>> (XEN) [VT-D]iommu.c:1325: d0:PCIe: map bdf = 3:0.0 >>> (XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = 5:e.0 >>> (XEN) [VT-D]iommu.c:1325: d0:PCIe: map bdf = 7:0.0 >>> (XEN) [VT-D]iommu.c:1325: d0:PCIe: map bdf = 8:0.0 >>> (XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = fe:0.0 >>> (XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = fe:0.1 >>> (XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = fe:2.0 >>> (XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = fe:2.1 >>> (XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = fe:2.4 >>> (XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = fe:2.5 >>> (XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = fe:3.0 >>> (XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = fe:3.1 >>> (XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = fe:3.2 >>> (XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = fe:3.4 >>> (XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = fe:4.0 >>> (XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = fe:4.1 >>> (XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = fe:4.2 >>> (XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = fe:4.3 >>> (XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = fe:5.0 >>> (XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = fe:5.1 >>> (XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = fe:5.2 >>> (XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = fe:5.3 >>> (XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = fe:6.0 >>> (XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = fe:6.1 >>> (XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = fe:6.2 >>> (XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = fe:6.3 >>> (XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = ff:0.0 >>> (XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = ff:0.1 >>> (XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = ff:2.0 >>> (XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = ff:2.1 >>> (XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = ff:2.4 >>> (XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = ff:2.5 >>> (XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = ff:3.0 >>> (XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = ff:3.1 >>> (XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = ff:3.2 >>> (XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = ff:3.4 >>> (XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = ff:4.0 >>> (XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = ff:4.1 >>> (XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = ff:4.2 >>> (XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = ff:4.3 >>> (XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = ff:5.0 >>> (XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = ff:5.1 >>> (XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = ff:5.2 >>> (XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = ff:5.3 >>> (XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = ff:6.0 >>> (XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = ff:6.1 >>> (XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = ff:6.2 >>> (XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = ff:6.3 >>> (XEN) [VT-D]iommu.c:695: iommu_enable_translation: iommu->reg >>> ffff82c3fff57000 >>> (XEN) *** LOADING DOMAIN 0 *** >>> (XEN) Xen kernel: 64-bit, lsb, compat32 >>> (XEN) Dom0 kernel: 64-bit, PAE, lsb, paddr 0x1000000 -> 0x26b6000 >>> (XEN) PHYSICAL MEMORY ARRANGEMENT: >>> (XEN) Dom0 alloc.: 0000000100000000->0000000120000000 (2937045 pages >>> to be allocated) >>> (XEN) VIRTUAL MEMORY ARRANGEMENT: >>> (XEN) Loaded kernel: ffffffff81000000->ffffffff826b6000 >>> (XEN) Init. ramdisk: ffffffff826b6000->ffffffff8f7d7600 >>> (XEN) Phys-Mach map: ffffffff8f7d8000->ffffffff90f406a8 >>> (XEN) Start info: ffffffff90f41000->ffffffff90f414b4 >>> (XEN) Page tables: ffffffff90f42000->ffffffff90fcf000 >>> (XEN) Boot stack: ffffffff90fcf000->ffffffff90fd0000 >>> (XEN) TOTAL: ffffffff80000000->ffffffff91400000 >>> (XEN) ENTRY ADDRESS: ffffffff819be200 >>> (XEN) Dom0 has maximum 16 VCPUs >>> (XEN) Scrubbing Free RAM: .done. >>> (XEN) Xen trace buffers: disabled >>> (XEN) Std. Loglevel: All >>> (XEN) Guest Loglevel: All >>> (XEN) ********************************************** >>> (XEN) ******* WARNING: CONSOLE OUTPUT IS SYNCHRONOUS >>> (XEN) ******* This option is intended to aid debugging of Xen by >>> ensuring >>> (XEN) ******* that all output is synchronously delivered on the serial >>> line. >>> (XEN) ******* However it can introduce SIGNIFICANT latencies and affect >>> (XEN) ******* timekeeping. It is NOT recommended for production use! >>> (XEN) ********************************************** >>> (XEN) 3... 2... 1... >>> (XEN) *** Serial input -> DOM0 (type ''CTRL-a'' three times to switch >>> input to Xen) >>> (XEN) Freed 164kB init memory. >>> mapping kernel into physical memory >>> Xen: setup ISA identity maps >>> about to get started... >>> (XEN) PCI add device 00:00.0 >>> (XEN) PCI add device 00:01.0 >>> (XEN) PCI add device 00:03.0 >>> (XEN) PCI add device 00:07.0 >>> (XEN) PCI add device 00:14.0 >>> (XEN) PCI add device 00:14.1 >>> (XEN) PCI add device 00:14.2 >>> (XEN) PCI add device 00:14.3 >>> (XEN) PCI add device 00:16.0 >>> (XEN) PCI add device 00:16.1 >>> (XEN) PCI add device 00:16.2 >>> (XEN) PCI add device 00:16.3 >>> (XEN) PCI add device 00:16.4 >>> (XEN) PCI add device 00:16.5 >>> (XEN) PCI add device 00:16.6 >>> (XEN) PCI add device 00:16.7 >>> (XEN) PCI add device 00:1a.0 >>> (XEN) PCI add device 00:1a.1 >>> (XEN) PCI add device 00:1a.2 >>> (XEN) PCI add device 00:1a.7 >>> (XEN) PCI add device 00:1b.0 >>> (XEN) PCI add device 00:1c.0 >>> (XEN) PCI add device 00:1c.4 >>> (XEN) PCI add device 00:1c.5 >>> (XEN) PCI add device 00:1d.0 >>> (XEN) PCI add device 00:1d.1 >>> (XEN) PCI add device 00:1d.2 >>> (XEN) PCI add device 00:1d.7 >>> (XEN) PCI add device 00:1e.0 >>> (XEN) PCI add device 00:1f.0 >>> (XEN) PCI add device 00:1f.2 >>> (XEN) PCI add device 00:1f.3 >>> (XEN) PCI add device 01:00.0 >>> (XEN) PCI add device 03:00.0 >>> (XEN) PCI add device 04:00.0 >>> (XEN) PCI add device 04:00.2 >>> (XEN) PCI add device 05:0e.0 >>> (XEN) PCI add device 07:00.0 >>> (XEN) PCI add device 08:00.0 >>> (XEN) cpuid.MWAIT[.eax=40, .ebx=40, .ecx=3, .edx=1120] >>> (XEN) Monitor-Mwait will be used to enter C-1 state >>> (XEN) cpuid.MWAIT[.eax=40, .ebx=40, .ecx=3, .edx=1120] >>> (XEN) Monitor-Mwait will be used to enter C-3 state >>> (XEN) cpuid.MWAIT[.eax=40, .ebx=40, .ecx=3, .edx=1120] >>> (XEN) Monitor-Mwait will be used to enter C-3 state >>> (XEN) cpuid.MWAIT[.eax=40, .ebx=40, .ecx=3, .edx=1120] >>> (XEN) Monitor-Mwait will be used to enter C-1 state >>> (XEN) cpuid.MWAIT[.eax=40, .ebx=40, .ecx=3, .edx=1120] >>> (XEN) Monitor-Mwait will be used to enter C-3 state >>> (XEN) cpuid.MWAIT[.eax=40, .ebx=40, .ecx=3, .edx=1120] >>> (XEN) Monitor-Mwait will be used to enter C-3 state >>> (XEN) cpuid.MWAIT[.eax=40, .ebx=40, .ecx=3, .edx=1120] >>> (XEN) Monitor-Mwait will be used to enter C-1 state >>> (XEN) cpuid.MWAIT[.eax=40, .ebx=40, .ecx=3, .edx=1120] >>> (XEN) Monitor-Mwait will be used to enter C-3 state >>> (XEN) cpuid.MWAIT[.eax=40, .ebx=40, .ecx=3, .edx=1120] >>> (XEN) Monitor-Mwait will be used to enter C-3 state >>> (XEN) cpuid.MWAIT[.eax=40, .ebx=40, .ecx=3, .edx=1120] >>> (XEN) Monitor-Mwait will be used to enter C-1 state >>> (XEN) cpuid.MWAIT[.eax=40, .ebx=40, .ecx=3, .edx=1120] >>> (XEN) Monitor-Mwait will be used to enter C-3 state >>> (XEN) cpuid.MWAIT[.eax=40, .ebx=40, .ecx=3, .edx=1120] >>> (XEN) Monitor-Mwait will be used to enter C-3 state >>> (XEN) cpuid.MWAIT[.eax=40, .ebx=40, .ecx=3, .edx=1120] >>> (XEN) Monitor-Mwait will be used to enter C-1 state >>> (XEN) cpuid.MWAIT[.eax=40, .ebx=40, .ecx=3, .edx=1120] >>> (XEN) Monitor-Mwait will be used to enter C-3 state >>> (XEN) cpuid.MWAIT[.eax=40, .ebx=40, .ecx=3, .edx=1120] >>> (XEN) Monitor-Mwait will be used to enter C-3 state >>> (XEN) cpuid.MWAIT[.eax=40, .ebx=40, .ecx=3, .edx=1120] >>> (XEN) Monitor-Mwait will be used to enter C-1 state >>> (XEN) cpuid.MWAIT[.eax=40, .ebx=40, .ecx=3, .edx=1120] >>> (XEN) Monitor-Mwait will be used to enter C-3 state >>> (XEN) cpuid.MWAIT[.eax=40, .ebx=40, .ecx=3, .edx=1120] >>> (XEN) Monitor-Mwait will be used to enter C-3 state >>> (XEN) cpuid.MWAIT[.eax=40, .ebx=40, .ecx=3, .edx=1120] >>> (XEN) Monitor-Mwait will be used to enter C-1 state >>> (XEN) cpuid.MWAIT[.eax=40, .ebx=40, .ecx=3, .edx=1120] >>> (XEN) Monitor-Mwait will be used to enter C-3 state >>> (XEN) cpuid.MWAIT[.eax=40, .ebx=40, .ecx=3, .edx=1120] >>> (XEN) Monitor-Mwait will be used to enter C-3 state >>> (XEN) cpuid.MWAIT[.eax=40, .ebx=40, .ecx=3, .edx=1120] >>> (XEN) Monitor-Mwait will be used to enter C-1 state >>> (XEN) cpuid.MWAIT[.eax=40, .ebx=40, .ecx=3, .edx=1120] >>> (XEN) Monitor-Mwait will be used to enter C-3 state >>> (XEN) cpuid.MWAIT[.eax=40, .ebx=40, .ecx=3, .edx=1120] >>> (XEN) Monitor-Mwait will be used to enter C-3 state >>> (XEN) cpuid.MWAIT[.eax=40, .ebx=40, .ecx=3, .edx=1120] >>> (XEN) Monitor-Mwait will be used to enter C-1 state >>> (XEN) cpuid.MWAIT[.eax=40, .ebx=40, .ecx=3, .edx=1120] >>> (XEN) Monitor-Mwait will be used to enter C-3 state >>> (XEN) cpuid.MWAIT[.eax=40, .ebx=40, .ecx=3, .edx=1120] >>> (XEN) Monitor-Mwait will be used to enter C-3 state >>> (XEN) cpuid.MWAIT[.eax=40, .ebx=40, .ecx=3, .edx=1120] >>> (XEN) Monitor-Mwait will be used to enter C-1 state >>> (XEN) cpuid.MWAIT[.eax=40, .ebx=40, .ecx=3, .edx=1120] >>> (XEN) Monitor-Mwait will be used to enter C-3 state >>> (XEN) cpuid.MWAIT[.eax=40, .ebx=40, .ecx=3, .edx=1120] >>> (XEN) Monitor-Mwait will be used to enter C-3 state >>> (XEN) cpuid.MWAIT[.eax=40, .ebx=40, .ecx=3, .edx=1120] >>> (XEN) Monitor-Mwait will be used to enter C-1 state >>> (XEN) cpuid.MWAIT[.eax=40, .ebx=40, .ecx=3, .edx=1120] >>> (XEN) Monitor-Mwait will be used to enter C-3 state >>> (XEN) cpuid.MWAIT[.eax=40, .ebx=40, .ecx=3, .edx=1120] >>> (XEN) Monitor-Mwait will be used to enter C-3 state >>> (XEN) cpuid.MWAIT[.eax=40, .ebx=40, .ecx=3, .edx=1120] >>> (XEN) Monitor-Mwait will be used to enter C-1 state >>> (XEN) cpuid.MWAIT[.eax=40, .ebx=40, .ecx=3, .edx=1120] >>> (XEN) Monitor-Mwait will be used to enter C-3 state >>> (XEN) cpuid.MWAIT[.eax=40, .ebx=40, .ecx=3, .edx=1120] >>> (XEN) Monitor-Mwait will be used to enter C-3 state >>> (XEN) cpuid.MWAIT[.eax=40, .ebx=40, .ecx=3, .edx=1120] >>> (XEN) Monitor-Mwait will be used to enter C-1 state >>> (XEN) cpuid.MWAIT[.eax=40, .ebx=40, .ecx=3, .edx=1120] >>> (XEN) Monitor-Mwait will be used to enter C-3 state >>> (XEN) cpuid.MWAIT[.eax=40, .ebx=40, .ecx=3, .edx=1120] >>> (XEN) Monitor-Mwait will be used to enter C-3 state >>> (XEN) cpuid.MWAIT[.eax=40, .ebx=40, .ecx=3, .edx=1120] >>> (XEN) Monitor-Mwait will be used to enter C-1 state >>> (XEN) cpuid.MWAIT[.eax=40, .ebx=40, .ecx=3, .edx=1120] >>> (XEN) Monitor-Mwait will be used to enter C-3 state >>> (XEN) cpuid.MWAIT[.eax=40, .ebx=40, .ecx=3, .edx=1120] >>> (XEN) Monitor-Mwait will be used to enter C-3 state >>> (XEN) cpuid.MWAIT[.eax=40, .ebx=40, .ecx=3, .edx=1120] >>> (XEN) Monitor-Mwait will be used to enter C-1 state >>> (XEN) cpuid.MWAIT[.eax=40, .ebx=40, .ecx=3, .edx=1120] >>> (XEN) Monitor-Mwait will be used to enter C-3 state >>> (XEN) cpuid.MWAIT[.eax=40, .ebx=40, .ecx=3, .edx=1120] >>> (XEN) Monitor-Mwait will be used to enter C-3 state >>> (XEN) cpuid.MWAIT[.eax=40, .ebx=40, .ecx=3, .edx=1120] >>> (XEN) Monitor-Mwait will be used to enter C-1 state >>> (XEN) cpuid.MWAIT[.eax=40, .ebx=40, .ecx=3, .edx=1120] >>> (XEN) Monitor-Mwait will be used to enter C-3 state >>> (XEN) cpuid.MWAIT[.eax=40, .ebx=40, .ecx=3, .edx=1120] >>> (XEN) Monitor-Mwait will be used to enter C-3 state >>> (XEN) irq.c:1139:d0 Cannot bind IRQ 4 to guest. In use by ''ns16550''. >>> (XEN) irq.c:1139:d0 Cannot bind IRQ 2 to guest. In use by ''cascade''. >>> (XEN) irq.c:1139:d0 Cannot bind IRQ 4 to guest. In use by ''ns16550''. >>> (XEN) irq.c:1139:d0 Cannot bind IRQ 2 to guest. In use by ''cascade''. >>> (XEN) irq.c:1139:d0 Cannot bind IRQ 4 to guest. In use by ''ns16550''. >>> (XEN) irq.c:1139:d0 Cannot bind IRQ 2 to guest. In use by ''cascade''. >>> (XEN) irq.c:1139:d0 Cannot bind IRQ 4 to guest. In use by ''ns16550''. >>> (XEN) irq.c:1139:d0 Cannot bind IRQ 2 to guest. In use by ''cascade''. >>> (XEN) [VT-D]iommu.c:821: iommu_fault_status: Primary Pending Fault >>> (XEN) [VT-D]iommu.c:796: DMAR:[DMA Write] Request device [05:08.0] fault >>> addr 203a09000, iommu reg = ffff82c3fff57000 >>> (XEN) DMAR:[fault reason 02h] Present bit in context entry is clear >>> (XEN) print_vtd_entries: iommu = ffff83013fffaee0 bdf = 5:8.0 gmfn >>> 203a09 >>> (XEN) root_entry = ffff83013ff37000 >>> (XEN) root_entry[5] = 13cf12001 >>> (XEN) context = ffff83013cf12000 >>> (XEN) context[40] = 0_0 >>> (XEN) ctxt_entry[40] not present >>> (XEN) [VT-D]iommu.c:796: DMAR:[DMA Write] Request device [05:08.0] fault >>> addr 203eba000, iommu reg = ffff82c3fff57000 >>> (XEN) DMAR:[fault reason 02h] Present bit in context entry is clear >>> (XEN) print_vtd_entries: iommu = ffff83013fffaee0 bdf = 5:8.0 gmfn >>> 203eba >>> (XEN) root_entry = ffff83013ff37000 >>> (XEN) root_entry[5] = 13cf12001 >>> (XEN) context = ffff83013cf12000 >>> (XEN) context[40] = 0_0 >>> (XEN) ctxt_entry[40] not present >>> (XEN) [VT-D]iommu.c:821: iommu_fault_status: Primary Pending Fault >>> (XEN) [VT-D]iommu.c:796: DMAR:[DMA Write] Request device [05:08.0] fault >>> addr 204e11000, iommu reg = ffff82c3fff57000 >>> (XEN) DMAR:[fault reason 02h] Present bit in context entry is clear >>> (XEN) print_vtd_entries: iommu = ffff83013fffaee0 bdf = 5:8.0 gmfn >>> 204e11 >>> (XEN) root_entry = ffff83013ff37000 >>> (XEN) root_entry[5] = 13cf12001 >>> (XEN) context = ffff83013cf12000 >>> (XEN) context[40] = 0_0 >>> (XEN) ctxt_entry[40] not present >>> (XEN) [VT-D]iommu.c:821: iommu_fault_status: Primary Pending Fault >>> (XEN) [VT-D]iommu.c:796: DMAR:[DMA Write] Request device [05:08.0] fault >>> addr 2061e2000, iommu reg = ffff82c3fff57000 >>> (XEN) DMAR:[fault reason 02h] Present bit in context entry is clear >>> (XEN) print_vtd_entries: iommu = ffff83013fffaee0 bdf = 5:8.0 gmfn >>> 2061e2 >>> (XEN) root_entry = ffff83013ff37000 >>> (XEN) root_entry[5] = 13cf12001 >>> (XEN) context = ffff83013cf12000 >>> (XEN) context[40] = 0_0 >>> (XEN) ctxt_entry[40] not present >>> (XEN) [VT-D]iommu.c:796: DMAR:[DMA Write] Request device [05:08.0] fault >>> addr 205043000, iommu reg = ffff82c3fff57000 >>> (XEN) DMAR:[fault reason 02h] Present bit in context entry is clear >>> (XEN) print_vtd_entries: iommu = ffff83013fffaee0 bdf = 5:8.0 gmfn >>> 205043 >>> (XEN) root_entry = ffff83013ff37000 >>> (XEN) root_entry[5] = 13cf12001 >>> (XEN) context = ffff83013cf12000 >>> (XEN) context[40] = 0_0 >>> (XEN) ctxt_entry[40] not present >>> (XEN) [VT-D]iommu.c:821: iommu_fault_status: Primary Pending Fault >>> (XEN) [VT-D]iommu.c:796: DMAR:[DMA Write] Request device [05:08.0] fault >>> addr 20552b000, iommu reg = ffff82c3fff57000 >>> (XEN) DMAR:[fault reason 02h] Present bit in context entry is clear >>> (XEN) print_vtd_entries: iommu = ffff83013fffaee0 bdf = 5:8.0 gmfn >>> 20552b >>> (XEN) root_entry = ffff83013ff37000 >>> (XEN) root_entry[5] = 13cf12001 >>> (XEN) context = ffff83013cf12000 >>> (XEN) context[40] = 0_0 >>> (XEN) ctxt_entry[40] not present >>> (XEN) [VT-D]iommu.c:821: iommu_fault_status: Primary Pending Fault >>> (XEN) [VT-D]iommu.c:796: DMAR:[DMA Write] Request device [05:08.0] fault >>> addr 205708000, iommu reg = ffff82c3fff57000 >>> (XEN) DMAR:[fault reason 02h] Present bit in context entry is clear >>> (XEN) print_vtd_entries: iommu = ffff83013fffaee0 bdf = 5:8.0 gmfn >>> 205708 >>> (XEN) root_entry = ffff83013ff37000 >>> (XEN) root_entry[5] = 13cf12001 >>> (XEN) context = ffff83013cf12000 >>> (XEN) context[40] = 0_0 >>> (XEN) ctxt_entry[40] not present >>> (XEN) [VT-D]iommu.c:796: DMAR:[DMA Write] Request device [05:08.0] fault >>> addr 2060c0000, iommu reg = ffff82c3fff57000 >>> (XEN) DMAR:[fault reason 02h] Present bit in context entry is clear >>> (XEN) print_vtd_entries: iommu = ffff83013fffaee0 bdf = 5:8.0 gmfn >>> 2060c0 >>> (XEN) root_entry = ffff83013ff37000 >>> (XEN) root_entry[5] = 13cf12001 >>> (XEN) context = ffff83013cf12000 >>> (XEN) context[40] = 0_0 >>> (XEN) ctxt_entry[40] not present >>> (XEN) [VT-D]iommu.c:821: iommu_fault_status: Primary Pending Fault >>> (XEN) [VT-D]iommu.c:796: DMAR:[DMA Write] Request device [05:08.0] fault >>> addr 206591000, iommu reg = ffff82c3fff57000 >>> (XEN) DMAR:[fault reason 02h] Present bit in context entry is clear >>> (XEN) print_vtd_entries: iommu = ffff83013fffaee0 bdf = 5:8.0 gmfn >>> 206591 >>> (XEN) root_entry = ffff83013ff37000 >>> (XEN) root_entry[5] = 13cf12001 >>> (XEN) context = ffff83013cf12000 >>> (XEN) context[40] = 0_0 >>> (XEN) ctxt_entry[40] not present >>> (XEN) [VT-D]iommu.c:796: DMAR:[DMA Write] Request device [05:08.0] fault >>> addr 204353000, iommu reg = ffff82c3fff57000 >>> (XEN) DMAR:[fault reason 02h] Present bit in context entry is clear >>> (XEN) print_vtd_entries: iommu = ffff83013fffaee0 bdf = 5:8.0 gmfn >>> 204353 >>> (XEN) root_entry = ffff83013ff37000 >>> (XEN) root_entry[5] = 13cf12001 >>> (XEN) context = ffff83013cf12000 >>> (XEN) context[40] = 0_0 >>> (XEN) ctxt_entry[40] not present >>> (XEN) [VT-D]iommu.c:821: iommu_fault_status: Primary Pending Fault >>> (XEN) [VT-D]iommu.c:796: DMAR:[DMA Write] Request device [05:08.0] fault >>> addr 2061f2000, iommu reg = ffff82c3fff57000 >>> (XEN) DMAR:[fault reason 02h] Present bit in context entry is clear >>> (XEN) print_vtd_entries: iommu = ffff83013fffaee0 bdf = 5:8.0 gmfn >>> 2061f2 >>> (XEN) root_entry = ffff83013ff37000 >>> (XEN) root_entry[5] = 13cf12001 >>> (XEN) context = ffff83013cf12000 >>> (XEN) context[40] = 0_0 >>> (XEN) ctxt_entry[40] not present >>> (XEN) [VT-D]iommu.c:796: DMAR:[DMA Write] Request device [05:08.0] fault >>> addr 204306000, iommu reg = ffff82c3fff57000 >>> (XEN) DMAR:[fault reason 02h] Present bit in context entry is clear >>> (XEN) print_vtd_entries: iommu = ffff83013fffaee0 bdf = 5:8.0 gmfn >>> 204306 >>> (XEN) root_entry = ffff83013ff37000 >>> (XEN) root_entry[5] = 13cf12001 >>> (XEN) context = ffff83013cf12000 >>> (XEN) context[40] = 0_0 >>> (XEN) ctxt_entry[40] not present >>> (XEN) [VT-D]iommu.c:821: iommu_fault_status: Primary Pending Fault >>> (XEN) [VT-D]iommu.c:796: DMAR:[DMA Write] Request device [05:08.0] fault >>> addr 205f6b000, iommu reg = ffff82c3fff57000 >>> (XEN) DMAR:[fault reason 02h] Present bit in context entry is clear >>> (XEN) print_vtd_entries: iommu = ffff83013fffaee0 bdf = 5:8.0 gmfn >>> 205f6b >>> (XEN) root_entry = ffff83013ff37000 >>> (XEN) root_entry[5] = 13cf12001 >>> (XEN) context = ffff83013cf12000 >>> (XEN) context[40] = 0_0 >>> (XEN) ctxt_entry[40] not present >>> (XEN) [VT-D]iommu.c:796: DMAR:[DMA Write] Request device [05:08.0] fault >>> addr 205665000, iommu reg = ffff82c3fff57000 >>> (XEN) DMAR:[fault reason 02h] Present bit in context entry is clear >>> (XEN) print_vtd_entries: iommu = ffff83013fffaee0 bdf = 5:8.0 gmfn >>> 205665 >>> (XEN) root_entry = ffff83013ff37000 >>> (XEN) root_entry[5] = 13cf12001 >>> (XEN) context = ffff83013cf12000 >>> (XEN) context[40] = 0_0 >>> (XEN) ctxt_entry[40] not present >>> (XEN) [VT-D]iommu.c:821: iommu_fault_status: Primary Pending Fault >>> (XEN) [VT-D]iommu.c:796: DMAR:[DMA Write] Request device [05:08.0] fault >>> addr 2045a0000, iommu reg = ffff82c3fff57000 >>> (XEN) DMAR:[fault reason 02h] Present bit in context entry is clear >>> (XEN) print_vtd_entries: iommu = ffff83013fffaee0 bdf = 5:8.0 gmfn >>> 2045a0 >>> (XEN) root_entry = ffff83013ff37000 >>> (XEN) root_entry[5] = 13cf12001 >>> (XEN) context = ffff83013cf12000 >>> (XEN) context[40] = 0_0 >>> (XEN) ctxt_entry[40] not present >>> (XEN) [VT-D]iommu.c:796: DMAR:[DMA Write] Request device [05:08.0] fault >>> addr 205669000, iommu reg = ffff82c3fff57000 >>> (XEN) DMAR:[fault reason 02h] Present bit in context entry is clear >>> (XEN) print_vtd_entries: iommu = ffff83013fffaee0 bdf = 5:8.0 gmfn >>> 205669 >>> (XEN) root_entry = ffff83013ff37000 >>> (XEN) root_entry[5] = 13cf12001 >>> (XEN) context = ffff83013cf12000 >>> (XEN) context[40] = 0_0 >>> (XEN) ctxt_entry[40] not present >>> (XEN) [VT-D]iommu.c:821: iommu_fault_status: Primary Pending Fault >>> (XEN) [VT-D]iommu.c:796: DMAR:[DMA Write] Request device [05:08.0] fault >>> addr 2042c6000, iommu reg = ffff82c3fff57000 >>> (XEN) DMAR:[fault reason 02h] Present bit in context entry is clear >>> (XEN) print_vtd_entries: iommu = ffff83013fffaee0 bdf = 5:8.0 gmfn >>> 2042c6 >>> (XEN) root_entry = ffff83013ff37000 >>> (XEN) root_entry[5] = 13cf12001 >>> (XEN) context = ffff83013cf12000 >>> (XEN) context[40] = 0_0 >>> (XEN) ctxt_entry[40] not present >>> (XEN) [VT-D]iommu.c:796: DMAR:[DMA Write] Request device [05:08.0] fault >>> addr 2061fe000, iommu reg = ffff82c3fff57000 >>> (XEN) DMAR:[fault reason 02h] Present bit in context entry is clear >>> (XEN) print_vtd_entries: iommu = ffff83013fffaee0 bdf = 5:8.0 gmfn >>> 2061fe >>> (XEN) root_entry = ffff83013ff37000 >>> (XEN) root_entry[5] = 13cf12001 >>> (XEN) context = ffff83013cf12000 >>> (XEN) context[40] = 0_0 >>> (XEN) ctxt_entry[40] not present >>> (XEN) [VT-D]iommu.c:821: iommu_fault_status: Primary Pending Fault >>> (XEN) [VT-D]iommu.c:796: DMAR:[DMA Write] Request device [05:08.0] fault >>> addr 20560a000, iommu reg = ffff82c3fff57000 >>> (XEN) DMAR:[fault reason 02h] Present bit in context entry is clear >>> (XEN) print_vtd_entries: iommu = ffff83013fffaee0 bdf = 5:8.0 gmfn >>> 20560a >>> (XEN) root_entry = ffff83013ff37000 >>> (XEN) root_entry[5] = 13cf12001 >>> (XEN) context = ffff83013cf12000 >>> (XEN) context[40] = 0_0 >>> (XEN) ctxt_entry[40] not present >>> (XEN) [VT-D]iommu.c:796: DMAR:[DMA Write] Request device [05:08.0] fault >>> addr 206003000, iommu reg = ffff82c3fff57000 >>> (XEN) DMAR:[fault reason 02h] Present bit in context entry is clear >>> (XEN) print_vtd_entries: iommu = ffff83013fffaee0 bdf = 5:8.0 gmfn >>> 206003 >>> (XEN) root_entry = ffff83013ff37000 >>> (XEN) root_entry[5] = 13cf12001 >>> (XEN) context = ffff83013cf12000 >>> (XEN) context[40] = 0_0 >>> (XEN) ctxt_entry[40] not present >>> (XEN) [VT-D]iommu.c:821: iommu_fault_status: Primary Pending Fault >>> (XEN) [VT-D]iommu.c:796: DMAR:[DMA Write] Request device [05:08.0] fault >>> addr 20583e000, iommu reg = ffff82c3fff57000 >>> (XEN) DMAR:[fault reason 02h] Present bit in context entry is clear >>> (XEN) print_vtd_entries: iommu = ffff83013fffaee0 bdf = 5:8.0 gmfn >>> 20583e >>> (XEN) root_entry = ffff83013ff37000 >>> (XEN) root_entry[5] = 13cf12001 >>> (XEN) context = ffff83013cf12000 >>> (XEN) context[40] = 0_0 >>> (XEN) ctxt_entry[40] not present >>> (XEN) [VT-D]iommu.c:796: DMAR:[DMA Write] Request device [05:08.0] fault >>> addr 205615000, iommu reg = ffff82c3fff57000 >>> (XEN) DMAR:[fault reason 02h] Present bit in context entry is clear >>> (XEN) print_vtd_entries: iommu = ffff83013fffaee0 bdf = 5:8.0 gmfn >>> 205615 >>> (XEN) root_entry = ffff83013ff37000 >>> (XEN) root_entry[5] = 13cf12001 >>> (XEN) context = ffff83013cf12000 >>> (XEN) context[40] = 0_0 >>> (XEN) ctxt_entry[40] not present >>> (XEN) [VT-D]iommu.c:796: DMAR:[DMA Write] Request device [05:08.0] fault >>> addr 204265000, iommu reg = ffff82c3fff57000 >>> (XEN) DMAR:[fault reason 02h] Present bit in context entry is clear >>> (XEN) print_vtd_entries: iommu = ffff83013fffaee0 bdf = 5:8.0 gmfn >>> 204265 >>> (XEN) root_entry = ffff83013ff37000 >>> (XEN) root_entry[5] = 13cf12001 >>> (XEN) context = ffff83013cf12000 >>> (XEN) context[40] = 0_0 >>> (XEN) ctxt_entry[40] not present >>> (XEN) [VT-D]iommu.c:821: iommu_fault_status: Primary Pending Fault >>> (XEN) [VT-D]iommu.c:796: DMAR:[DMA Write] Request device [05:08.0] fault >>> addr 207498000, iommu reg = ffff82c3fff57000 >>> (XEN) DMAR:[fault reason 02h] Present bit in context entry is clear >>> (XEN) print_vtd_entries: iommu = ffff83013fffaee0 bdf = 5:8.0 gmfn >>> 207498 >>> (XEN) root_entry = ffff83013ff37000 >>> (XEN) root_entry[5] = 13cf12001 >>> (XEN) context = ffff83013cf12000 >>> (XEN) context[40] = 0_0 >>> (XEN) ctxt_entry[40] not present >>> (XEN) [VT-D]iommu.c:821: iommu_fault_status: Primary Pending Fault >>> (XEN) [VT-D]iommu.c:796: DMAR:[DMA Write] Request device [05:08.0] fault >>> addr 2049d1000, iommu reg = ffff82c3fff57000 >>> (XEN) DMAR:[fault reason 02h] Present bit in context entry is clear >>> (XEN) print_vtd_entries: iommu = ffff83013fffaee0 bdf = 5:8.0 gmfn >>> 2049d1 >>> (XEN) root_entry = ffff83013ff37000 >>> (XEN) root_entry[5] = 13cf12001 >>> (XEN) context = ffff83013cf12000 >>> (XEN) context[40] = 0_0 >>> (XEN) ctxt_entry[40] not present >>> (XEN) [VT-D]iommu.c:821: iommu_fault_status: Primary Pending Fault >>> (XEN) [VT-D]iommu.c:796: DMAR:[DMA Write] Request device [05:08.0] fault >>> addr 20488e000, iommu reg = ffff82c3fff57000 >>> (XEN) DMAR:[fault reason 02h] Present bit in context entry is clear >>> (XEN) print_vtd_entries: iommu = ffff83013fffaee0 bdf = 5:8.0 gmfn >>> 20488e >>> (XEN) root_entry = ffff83013ff37000 >>> (XEN) root_entry[5] = 13cf12001 >>> (XEN) context = ffff83013cf12000 >>> (XEN) context[40] = 0_0 >>> (XEN) ctxt_entry[40] not present >>> (XEN) [VT-D]iommu.c:821: iommu_fault_status: Primary Pending Fault >>> (XEN) [VT-D]iommu.c:796: DMAR:[DMA Write] Request device [05:08.0] fault >>> addr 205495000, iommu reg = ffff82c3fff57000 >>> (XEN) DMAR:[fault reason 02h] Present bit in context entry is clear >>> (XEN) print_vtd_entries: iommu = ffff83013fffaee0 bdf = 5:8.0 gmfn >>> 205495 >>> (XEN) root_entry = ffff83013ff37000 >>> (XEN) root_entry[5] = 13cf12001 >>> (XEN) context = ffff83013cf12000 >>> (XEN) context[40] = 0_0 >>> (XEN) ctxt_entry[40] not present >>> (XEN) [VT-D]iommu.c:821: iommu_fault_status: Primary Pending Fault >>> (XEN) [VT-D]iommu.c:796: DMAR:[DMA Write] Request device [05:08.0] fault >>> addr 2072d8000, iommu reg = ffff82c3fff57000 >>> (XEN) DMAR:[fault reason 02h] Present bit in context entry is clear >>> (XEN) print_vtd_entries: iommu = ffff83013fffaee0 bdf = 5:8.0 gmfn >>> 2072d8 >>> (XEN) root_entry = ffff83013ff37000 >>> (XEN) root_entry[5] = 13cf12001 >>> (XEN) context = ffff83013cf12000 >>> (XEN) context[40] = 0_0 >>> (XEN) ctxt_entry[40] not present >>> (XEN) [VT-D]iommu.c:821: iommu_fault_status: Primary Pending Fault >>> (XEN) [VT-D]iommu.c:796: DMAR:[DMA Write] Request device [05:08.0] fault >>> addr 2055ae000, iommu reg = ffff82c3fff57000 >>> (XEN) DMAR:[fault reason 02h] Present bit in context entry is clear >>> (XEN) print_vtd_entries: iommu = ffff83013fffaee0 bdf = 5:8.0 gmfn >>> 2055ae >>> (XEN) root_entry = ffff83013ff37000 >>> (XEN) root_entry[5] = 13cf12001 >>> (XEN) context = ffff83013cf12000 >>> (XEN) context[40] = 0_0 >>> (XEN) ctxt_entry[40] not present >>> (XEN) [VT-D]iommu.c:821: iommu_fault_status: Primary Pending Fault >>> (XEN) [VT-D]iommu.c:796: DMAR:[DMA Write] Request device [05:08.0] fault >>> addr 205544000, iommu reg = ffff82c3fff57000 >>> (XEN) DMAR:[fault reason 02h] Present bit in context entry is clear >>> (XEN) print_vtd_entries: iommu = ffff83013fffaee0 bdf = 5:8.0 gmfn >>> 205544 >>> (XEN) root_entry = ffff83013ff37000 >>> (XEN) root_entry[5] = 13cf12001 >>> (XEN) context = ffff83013cf12000 >>> (XEN) context[40] = 0_0 >>> (XEN) ctxt_entry[40] not present >>> (XEN) [VT-D]iommu.c:796: DMAR:[DMA Write] Request device [05:08.0] fault >>> addr 204865000, iommu reg = ffff82c3fff57000 >>> (XEN) DMAR:[fault reason 02h] Present bit in context entry is clear >>> (XEN) print_vtd_entries: iommu = ffff83013fffaee0 bdf = 5:8.0 gmfn >>> 204865 >>> (XEN) root_entry = ffff83013ff37000 >>> (XEN) root_entry[5] = 13cf12001 >>> (XEN) context = ffff83013cf12000 >>> (XEN) context[40] = 0_0 >>> (XEN) ctxt_entry[40] not present >>> (XEN) [VT-D]iommu.c:821: iommu_fault_status: Primary Pending Fault >>> (XEN) [VT-D]iommu.c:796: DMAR:[DMA Write] Request device [05:08.0] fault >>> addr 2074be000, iommu reg = ffff82c3fff57000 >>> (XEN) DMAR:[fault reason 02h] Present bit in context entry is clear >>> (XEN) print_vtd_entries: iommu = ffff83013fffaee0 bdf = 5:8.0 gmfn >>> 2074be >>> (XEN) root_entry = ffff83013ff37000 >>> (XEN) root_entry[5] = 13cf12001 >>> (XEN) context = ffff83013cf12000 >>> (XEN) context[40] = 0_0 >>> (XEN) ctxt_entry[40] not present >>> >>> (XEN) [VT-D]iommu.c:796: DMAR:[DMA Write] Request device [05:08.0] fault >>> addr 204865000, iommu reg = ffff82c3fff57000 >>> (XEN) DMAR:[fault reason 02h] Present bit in context entry is clear >>> (XEN) print_vtd_entries: iommu = ffff83013fffaee0 bdf = 5:8.0 gmfn >>> 204865 >>> (XEN) root_entry = ffff83013ff37000 >>> (XEN) root_entry[5] = 13cf12001 >>> (XEN) context = ffff83013cf12000 >>> (XEN) context[40] = 0_0 >>> (XEN) ctxt_entry[40] not present >>> (XEN) [VT-D]iommu.c:821: iommu_fault_status: Primary Pending Fault >>> (XEN) [VT-D]iommu.c:796: DMAR:[DMA Write] Request device [05:08.0] fault >>> addr 2074be000, iommu reg = ffff82c3fff57000 >>> (XEN) DMAR:[fault reason 02h] Present bit in context entry is clear >>> (XEN) print_vtd_entries: iommu = ffff83013fffaee0 bdf = 5:8.0 gmfn >>> 2074be >>> (XEN) root_entry = ffff83013ff37000 >>> (XEN) root_entry[5] = 13cf12001 >>> (XEN) context = ffff83013cf12000 >>> (XEN) context[40] = 0_0 >>> (XEN) ctxt_entry[40] not present >>> >>> (XEN) [VT-D]iommu.c:796: DMAR:[DMA Write] Request device [05:08.0] fault >>> addr 204865000, iommu reg = ffff82c3fff57000 >>> (XEN) DMAR:[fault reason 02h] Present bit in context entry is clear >>> (XEN) print_vtd_entries: iommu = ffff83013fffaee0 bdf = 5:8.0 gmfn >>> 204865 >>> (XEN) root_entry = ffff83013ff37000 >>> (XEN) root_entry[5] = 13cf12001 >>> (XEN) context = ffff83013cf12000 >>> (XEN) context[40] = 0_0 >>> (XEN) ctxt_entry[40] not present >>> (XEN) [VT-D]iommu.c:821: iommu_fault_status: Primary Pending Fault >>> (XEN) [VT-D]iommu.c:796: DMAR:[DMA Write] Request device [05:08.0] fault >>> addr 2074be000, iommu reg = ffff82c3fff57000 >>> (XEN) DMAR:[fault reason 02h] Present bit in context entry is clear >>> (XEN) print_vtd_entries: iommu = ffff83013fffaee0 bdf = 5:8.0 gmfn >>> 2074be >>> (XEN) root_entry = ffff83013ff37000 >>> (XEN) root_entry[5] = 13cf12001 >>> (XEN) context = ffff83013cf12000 >>> (XEN) context[40] = 0_0 >>> (XEN) ctxt_entry[40] not present >>> >>> (XEN) [VT-D]iommu.c:796: DMAR:[DMA Write] Request device [05:08.0] fault >>> addr 204865000, iommu reg = ffff82c3fff57000 >>> (XEN) DMAR:[fault reason 02h] Present bit in context entry is clear >>> (XEN) print_vtd_entries: iommu = ffff83013fffaee0 bdf = 5:8.0 gmfn >>> 204865 >>> (XEN) root_entry = ffff83013ff37000 >>> (XEN) root_entry[5] = 13cf12001 >>> (XEN) context = ffff83013cf12000 >>> (XEN) context[40] = 0_0 >>> (XEN) ctxt_entry[40] not present >>> (XEN) [VT-D]iommu.c:821: iommu_fault_status: Primary Pending Fault >>> (XEN) [VT-D]iommu.c:796: DMAR:[DMA Write] Request device [05:08.0] fault >>> addr 2074be000, iommu reg = ffff82c3fff57000 >>> (XEN) DMAR:[fault reason 02h] Present bit in context entry is clear >>> (XEN) print_vtd_entries: iommu = ffff83013fffaee0 bdf = 5:8.0 gmfn >>> 2074be >>> (XEN) root_entry = ffff83013ff37000 >>> (XEN) root_entry[5] = 13cf12001 >>> (XEN) context = ffff83013cf12000 >>> (XEN) context[40] = 0_0 >>> (XEN) ctxt_entry[40] not present >>> >>> (XEN) [VT-D]iommu.c:796: DMAR:[DMA Write] Request device [05:08.0] fault >>> addr 204865000, iommu reg = ffff82c3fff57000 >>> (XEN) DMAR:[fault reason 02h] Present bit in context entry is clear >>> (XEN) print_vtd_entries: iommu = ffff83013fffaee0 bdf = 5:8.0 gmfn >>> 204865 >>> (XEN) root_entry = ffff83013ff37000 >>> (XEN) root_entry[5] = 13cf12001 >>> (XEN) context = ffff83013cf12000 >>> (XEN) context[40] = 0_0 >>> (XEN) ctxt_entry[40] not present >>> (XEN) [VT-D]iommu.c:821: iommu_fault_status: Primary Pending Fault >>> (XEN) [VT-D]iommu.c:796: DMAR:[DMA Write] Request device [05:08.0] fault >>> addr 2074be000, iommu reg = ffff82c3fff57000 >>> (XEN) DMAR:[fault reason 02h] Present bit in context entry is clear >>> (XEN) print_vtd_entries: iommu = ffff83013fffaee0 bdf = 5:8.0 gmfn >>> 2074be >>> (XEN) root_entry = ffff83013ff37000 >>> (XEN) root_entry[5] = 13cf12001 >>> (XEN) context = ffff83013cf12000 >>> (XEN) context[40] = 0_0 >>> (XEN) ctxt_entry[40] not present >>> >>> (XEN) [VT-D]iommu.c:796: DMAR:[DMA Write] Request device [05:08.0] fault >>> addr 204865000, iommu reg = ffff82c3fff57000 >>> (XEN) DMAR:[fault reason 02h] Present bit in context entry is clear >>> (XEN) print_vtd_entries: iommu = ffff83013fffaee0 bdf = 5:8.0 gmfn >>> 204865 >>> (XEN) root_entry = ffff83013ff37000 >>> (XEN) root_entry[5] = 13cf12001 >>> (XEN) context = ffff83013cf12000 >>> (XEN) context[40] = 0_0 >>> (XEN) ctxt_entry[40] not present >>> (XEN) [VT-D]iommu.c:821: iommu_fault_status: Primary Pending Fault >>> (XEN) [VT-D]iommu.c:796: DMAR:[DMA Write] Request device [05:08.0] fault >>> addr 2074be000, iommu reg = ffff82c3fff57000 >>> (XEN) DMAR:[fault reason 02h] Present bit in context entry is clear >>> (XEN) print_vtd_entries: iommu = ffff83013fffaee0 bdf = 5:8.0 gmfn >>> 2074be >>> (XEN) root_entry = ffff83013ff37000 >>> (XEN) root_entry[5] = 13cf12001 >>> (XEN) context = ffff83013cf12000 >>> (XEN) context[40] = 0_0 >>> (XEN) ctxt_entry[40] not present >>> >>> (XEN) [VT-D]iommu.c:796: DMAR:[DMA Write] Request device [05:08.0] fault >>> addr 204865000, iommu reg = ffff82c3fff57000 >>> (XEN) DMAR:[fault reason 02h] Present bit in context entry is clear >>> (XEN) print_vtd_entries: iommu = ffff83013fffaee0 bdf = 5:8.0 gmfn >>> 204865 >>> (XEN) root_entry = ffff83013ff37000 >>> (XEN) root_entry[5] = 13cf12001 >>> (XEN) context = ffff83013cf12000 >>> (XEN) context[40] = 0_0 >>> (XEN) ctxt_entry[40] not present >>> (XEN) [VT-D]iommu.c:821: iommu_fault_status: Primary Pending Fault >>> (XEN) [VT-D]iommu.c:796: DMAR:[DMA Write] Request device [05:08.0] fault >>> addr 2074be000, iommu reg = ffff82c3fff57000 >>> (XEN) DMAR:[fault reason 02h] Present bit in context entry is clear >>> (XEN) print_vtd_entries: iommu = ffff83013fffaee0 bdf = 5:8.0 gmfn >>> 2074be >>> (XEN) root_entry = ffff83013ff37000 >>> (XEN) root_entry[5] = 13cf12001 >>> (XEN) context = ffff83013cf12000 >>> (XEN) context[40] = 0_0 >>> (XEN) ctxt_entry[40] not present >>> >>> (XEN) context[40] = 0_0 >>> (XEN) ctxt_entry[40] not present >>> (XEN) [VT-D]iommu.c:796: DMAR:[DMA Write] Request device [05:08.0] fault >>> addr 204865000, iommu reg = ffff82c3fff57000 >>> (XEN) DMAR:[fault reason 02h] Present bit in context entry is clear >>> (XEN) print_vtd_entries: iommu = ffff83013fffaee0 bdf = 5:8.0 gmfn >>> 204865 >>> (XEN) root_entry = ffff83013ff37000 >>> (XEN) root_entry[5] = 13cf12001 >>> (XEN) context = ffff83013cf12000 >>> (XEN) context[40] = 0_0 >>> (XEN) ctxt_entry[40] not present >>> (XEN) [VT-D]iommu.c:821: iommu_fault_status: Primary Pending Fault >>> (XEN) [VT-D]iommu.c:796: DMAR:[DMA Write] Request device [05:08.0] fault >>> addr 2074be000, iommu reg = ffff82c3fff57000 >>> (XEN) DMAR:[fault reason 02h] Present bit in context entry is clear >>> (XEN) print_vtd_entries: iommu = ffff83013fffaee0 bdf = 5:8.0 gmfn >>> 2074be >>> (XEN) root_entry = ffff83013ff37000 >>> (XEN) root_entry[5] = 13cf12001 >>> (XEN) context = ffff83013cf12000 >>> (XEN) context[40] = 0_0 >>> (XEN) ctxt_entry[40] not present >>> >>> (XEN) context[40] = 0_0 >>> (XEN) ctxt_entry[40] not present >>> (XEN) [VT-D]iommu.c:796: DMAR:[DMA Write] Request device [05:08.0] fault >>> addr 204865000, iommu reg = ffff82c3fff57000 >>> (XEN) DMAR:[fault reason 02h] Present bit in context entry is clear >>> (XEN) print_vtd_entries: iommu = ffff83013fffaee0 bdf = 5:8.0 gmfn >>> 204865 >>> (XEN) root_entry = ffff83013ff37000 >>> (XEN) root_entry[5] = 13cf12001 >>> (XEN) context = ffff83013cf12000 >>> (XEN) context[40] = 0_0 >>> (XEN) ctxt_entry[40] not present >>> (XEN) [VT-D]iommu.c:821: iommu_fault_status: Primary Pending Fault >>> (XEN) [VT-D]iommu.c:796: DMAR:[DMA Write] Request device [05:08.0] fault >>> addr 2074be000, iommu reg = ffff82c3fff57000 >>> (XEN) DMAR:[fault reason 02h] Present bit in context entry is clear >>> (XEN) print_vtd_entries: iommu = ffff83013fffaee0 bdf = 5:8.0 gmfn >>> 2074be >>> (XEN) root_entry = ffff83013ff37000 >>> (XEN) root_entry[5] = 13cf12001 >>> (XEN) context = ffff83013cf12000 >>> (XEN) context[40] = 0_0 >>> (XEN) ctxt_entry[40] not present >>> >>> (XEN) context[40] = 0_0 >>> (XEN) ctxt_entry[40] not present >>> (XEN) [VT-D]iommu.c:796: DMAR:[DMA Write] Request device [05:08.0] fault >>> addr 204865000, iommu reg = ffff82c3fff57000 >>> (XEN) DMAR:[fault reason 02h] Present bit in context entry is clear >>> (XEN) print_vtd_entries: iommu = ffff83013fffaee0 bdf = 5:8.0 gmfn >>> 204865 >>> (XEN) root_entry = ffff83013ff37000 >>> (XEN) root_entry[5] = 13cf12001 >>> (XEN) context = ffff83013cf12000 >>> (XEN) context[40] = 0_0 >>> (XEN) ctxt_entry[40] not present >>> (XEN) [VT-D]iommu.c:821: iommu_fault_status: Primary Pending Fault >>> (XEN) [VT-D]iommu.c:796: DMAR:[DMA Write] Request device [05:08.0] fault >>> addr 2074be000, iommu reg = ffff82c3fff57000 >>> (XEN) DMAR:[fault reason 02h] Present bit in context entry is clear >>> (XEN) print_vtd_entries: iommu = ffff83013fffaee0 bdf = 5:8.0 gmfn >>> 2074be >>> (XEN) root_entry = ffff83013ff37000 >>> (XEN) root_entry[5] = 13cf12001 >>> (XEN) context = ffff83013cf12000 >>> (XEN) context[40] = 0_0 >>> (XEN) ctxt_entry[40] not present >>> >>> (XEN) context[40] = 0_0 >>> (XEN) ctxt_entry[40] not present >>> (XEN) [VT-D]iommu.c:796: DMAR:[DMA Write] Request device [05:08.0] fault >>> addr 204865000, iommu reg = ffff82c3fff57000 >>> (XEN) DMAR:[fault reason 02h] Present bit in context entry is clear >>> (XEN) print_vtd_entries: iommu = ffff83013fffaee0 bdf = 5:8.0 gmfn >>> 204865 >>> (XEN) root_entry = ffff83013ff37000 >>> (XEN) root_entry[5] = 13cf12001 >>> (XEN) context = ffff83013cf12000 >>> (XEN) context[40] = 0_0 >>> (XEN) ctxt_entry[40] not present >>> (XEN) [VT-D]iommu.c:821: iommu_fault_status: Primary Pending Fault >>> (XEN) [VT-D]iommu.c:796: DMAR:[DMA Write] Request device [05:08.0] fault >>> addr 2074be000, iommu reg = ffff82c3fff57000 >>> (XEN) DMAR:[fault reason 02h] Present bit in context entry is clear >>> (XEN) print_vtd_entries: iommu = ffff83013fffaee0 bdf = 5:8.0 gmfn >>> 2074be >>> (XEN) root_entry = ffff83013ff37000 >>> (XEN) root_entry[5] = 13cf12001 >>> (XEN) context = ffff83013cf12000 >>> (XEN) context[40] = 0_0 >>> (XEN) ctxt_entry[40] not present >>> >>> >>> _______________________________________________ >>> Xen-devel mailing list >>> Xen-devel@lists.xensource.com >>> http://lists.xensource.com/xen-devel >>> >>> >> _______________________________________________ >> Xen-devel mailing list >> Xen-devel@lists.xensource.com >> http://lists.xensource.com/xen-devel >>_______________________________________________ Xen-devel mailing list Xen-devel@lists.xensource.com http://lists.xensource.com/xen-devel
Konrad Rzeszutek Wilk
2010-Jun-02 14:49 UTC
Re: [Xen-devel] iommuu/vt-d issues with LSI MegaSAS (PERC5i)
On Wed, Jun 02, 2010 at 03:05:19PM +0800, Weidong Han wrote:> Pasi Kärkkäinen wrote: >> On Wed, Jun 02, 2010 at 09:23:37AM +0800, Weidong Han wrote: >> >>> This PCI-x card is not suitable for assignment. It contains an invisible >>> device 05:08.0 (lspci cannot show it), but this invisible device won''t >>> be mapped by VT-d because VT-d engine doesn''t know this device, so you >>> can see the DMAR faults on it. One workaround is to hard code to map >>> 05:08.0 when assign 05:0e.0. BTW, PCIe LSI card don''t have this problem. >>> >>> >> >> Note that this problem happens when booting up dom0.. >> > I see. all devices are assigned to dom0 in booting. It just needs to map > 05:08.0 as well when map 05:0e.0 in domain_context_mapping.Hey Weidong, Thank you the explanation. I am not that familiar with the VT-D chipset, but it seems that this issue also appears with CardBus controllers: http://lkml.org/lkml/2010/5/22/69 ? For this device, the problem should also appear with the newer kernels without using the Hypervisor and with CONFIG_DMAR enabled, right? Am I to understand that the workaround you are proposing is doing something akin to this: /* * * This program is free software; you can redistribute it and/or modify * it under the terms of the GNU General Public License v2.0 as published by * the Free Software Foundation * * This program is distributed in the hope that it will be useful, * but WITHOUT ANY WARRANTY; without even the implied warranty of * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the * GNU General Public License for more details. */ #include <linux/module.h> #include <linux/string.h> #include <linux/types.h> #include <linux/init.h> #include <linux/stat.h> #include <linux/err.h> #include <linux/ctype.h> #include <linux/slab.h> #include <linux/limits.h> #include <linux/device.h> #include <linux/pci.h> #include <linux/device.h> #include <linux/pci.h> #include <xen/interface/xen.h> #include <xen/interface/physdev.h> #include <asm/xen/hypervisor.h> #include <asm/xen/hypercall.h> #define LSI_HACK "0.1" MODULE_AUTHOR("Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>"); MODULE_DESCRIPTION("lsi hack"); MODULE_LICENSE("GPL"); MODULE_VERSION(LSI_HACK); static int __init lsi_hack_init(void) { int r = 0; struct physdev_manage_pci manage_pci = { .bus = 0x5, .devfn = PCI_DEVFN(8,0), }; r = HYPERVISOR_physdev_op(PHYSDEVOP_manage_pci_add, &manage_pci); return r; } static void __exit lsi_hack_exit(void) { int r = 0; struct physdev_manage_pci manage_pci; manage_pci.bus = 0x5; manage_pci.devfn = PCI_DEVFN(8,0); r = HYPERVISOR_physdev_op(PHYSDEVOP_manage_pci_remove, &manage_pci); if (r) printk(KERN_ERR "%s: %d\n", __FUNCTION__, r); } module_init(lsi_hack_init); module_exit(lsi_hack_exit); _______________________________________________ Xen-devel mailing list Xen-devel@lists.xensource.com http://lists.xensource.com/xen-devel
Weidong Han
2010-Jun-03 01:14 UTC
Re: [Xen-devel] iommuu/vt-d issues with LSI MegaSAS (PERC5i)
Konrad Rzeszutek Wilk wrote:> On Wed, Jun 02, 2010 at 03:05:19PM +0800, Weidong Han wrote: > >> Pasi Kärkkäinen wrote: >> >>> On Wed, Jun 02, 2010 at 09:23:37AM +0800, Weidong Han wrote: >>> >>> >>>> This PCI-x card is not suitable for assignment. It contains an invisible >>>> device 05:08.0 (lspci cannot show it), but this invisible device won''t >>>> be mapped by VT-d because VT-d engine doesn''t know this device, so you >>>> can see the DMAR faults on it. One workaround is to hard code to map >>>> 05:08.0 when assign 05:0e.0. BTW, PCIe LSI card don''t have this problem. >>>> >>>> >>>> >>> Note that this problem happens when booting up dom0.. >>> >>> >> I see. all devices are assigned to dom0 in booting. It just needs to map >> 05:08.0 as well when map 05:0e.0 in domain_context_mapping. >> > > Hey Weidong, > > Thank you the explanation. I am not that familiar with the VT-D chipset, > but it seems that this issue also appears with CardBus controllers: > http://lkml.org/lkml/2010/5/22/69 ? > > For this device, the problem should also appear with the newer kernels > without using the Hypervisor and with CONFIG_DMAR enabled, right? >yes.> Am I to understand that the workaround you are proposing is doing > something akin to this: >Your below code only make it work for dom0 by calling lsi_hack_init. but if you want to assign it to guest, it still cannot work. You can implement a a simple temporarily workaround like this: diff -r 2cd58d7d5db9 xen/drivers/passthrough/vtd/iommu.c --- a/xen/drivers/passthrough/vtd/iommu.c Tue Jun 01 20:40:34 2010 -0400 +++ b/xen/drivers/passthrough/vtd/iommu.c Wed Jun 02 14:09:37 2010 -0400 @@ -1339,6 +1339,15 @@ static int domain_context_mapping(struct if ( ret ) break; + /* NB. LSI workaround */ + if ( bus == 0x05 && PCI_SLOT(devfn) == 0x0e && PCI_FUNC(devfn) == 0x0 ) + { + ret = domain_context_mapping_one(domain, drhd->iommu, + 0x05, PCI_DEVFN(8, 0)); + if ( ret ) + break; + } + if ( find_upstream_bridge(&bus, &devfn, &secbus) < 1 ) break;> > /* > * > * This program is free software; you can redistribute it and/or modify > * it under the terms of the GNU General Public License v2.0 as published by > * the Free Software Foundation > * > * This program is distributed in the hope that it will be useful, > * but WITHOUT ANY WARRANTY; without even the implied warranty of > * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the > * GNU General Public License for more details. > */ > > #include <linux/module.h> > #include <linux/string.h> > #include <linux/types.h> > #include <linux/init.h> > #include <linux/stat.h> > #include <linux/err.h> > #include <linux/ctype.h> > #include <linux/slab.h> > #include <linux/limits.h> > #include <linux/device.h> > #include <linux/pci.h> > #include <linux/device.h> > > #include <linux/pci.h> > > #include <xen/interface/xen.h> > #include <xen/interface/physdev.h> > > #include <asm/xen/hypervisor.h> > #include <asm/xen/hypercall.h> > > #define LSI_HACK "0.1" > > MODULE_AUTHOR("Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>"); > MODULE_DESCRIPTION("lsi hack"); > MODULE_LICENSE("GPL"); > MODULE_VERSION(LSI_HACK); > > static int __init lsi_hack_init(void) > { > int r = 0; > > struct physdev_manage_pci manage_pci = { > .bus = 0x5, > .devfn = PCI_DEVFN(8,0), > }; > r = HYPERVISOR_physdev_op(PHYSDEVOP_manage_pci_add, > &manage_pci); > > return r; > } > > static void __exit lsi_hack_exit(void) > { > int r = 0; > struct physdev_manage_pci manage_pci; > > manage_pci.bus = 0x5; > manage_pci.devfn = PCI_DEVFN(8,0); > > r = HYPERVISOR_physdev_op(PHYSDEVOP_manage_pci_remove, > &manage_pci); > if (r) > printk(KERN_ERR "%s: %d\n", __FUNCTION__, r); > } > > module_init(lsi_hack_init); > module_exit(lsi_hack_exit); >_______________________________________________ Xen-devel mailing list Xen-devel@lists.xensource.com http://lists.xensource.com/xen-devel