Virtualization - Mar 2015 - virtio balloon: do not call blocking ops when !TASK_RUNNING

On Mon, Mar 02, 2015 at 10:37:26AM +1030, Rusty Russell
wrote:
> Thomas Huth <thuth at linux.vnet.ibm.com> writes:
> > On Thu, 26 Feb 2015 11:50:42 +1030
> > Rusty Russell <rusty at rustcorp.com.au> wrote:
> >
> >> Thomas Huth <thuth at linux.vnet.ibm.com> writes:
> >> >  Hi all,
> >> >
> >> > with the recent kernel 3.19, I get a kernel warning when I
start my
> >> > KVM guest on s390 with virtio balloon enabled:
> >> 
> >> The deeper problem is that virtio_ccw_get_config just silently
fails on
> >> OOM.
> >> 
> >> Neither get_config nor set_config are expected to fail.
> >
> > AFAIK this is currently not a problem. According to
> > http://lwn.net/Articles/627419/ these kmalloc calls never
> > fail because they allocate less than a page.
> 
> I strongly suggest you unlearn that fact.
> The fix for this is in two parts:
> 
> 1) Annotate using sched_annotate_sleep() and add a comment: we may spin
>    a few times in low memory situations, but this isn't a high
>    performance path.
> 
> 2) Handle get_config (and other) failure in some more elegant way.
> 
> Cheers,
> Rusty.
I agree, but I'd like to point out that even without kmalloc,
on s390 get_config is blocking - it's waiting
for a hardware interrupt.

And it makes sense: config is not data path, I don't think
we should spin there.

So I think besides these two parts, we still need my two patches:
    virtio-balloon: do not call blocking ops when !TASK_RUNNING
    virtio_console: avoid config access from irq
in 4.0.

agree?

On Mon, 2 Mar 2015 12:13:58 +0100
"Michael S. Tsirkin" <mst at redhat.com> wrote:
> On Mon, Mar 02, 2015 at 10:37:26AM +1030, Rusty Russell wrote:
> > Thomas Huth <thuth at linux.vnet.ibm.com> writes:
> > > On Thu, 26 Feb 2015 11:50:42 +1030
> > > Rusty Russell <rusty at rustcorp.com.au> wrote:
> > >
> > >> Thomas Huth <thuth at linux.vnet.ibm.com> writes:
> > >> >  Hi all,
> > >> >
> > >> > with the recent kernel 3.19, I get a kernel warning when
I start my
> > >> > KVM guest on s390 with virtio balloon enabled:
> > >> 
> > >> The deeper problem is that virtio_ccw_get_config just
silently fails on
> > >> OOM.
> > >> 
> > >> Neither get_config nor set_config are expected to fail.
> > >
> > > AFAIK this is currently not a problem. According to
> > > http://lwn.net/Articles/627419/ these kmalloc calls never
> > > fail because they allocate less than a page.
> > 
> > I strongly suggest you unlearn that fact.
> > The fix for this is in two parts:
> > 
> > 1) Annotate using sched_annotate_sleep() and add a comment: we may
spin
> >    a few times in low memory situations, but this isn't a high
> >    performance path.
> > 
> > 2) Handle get_config (and other) failure in some more elegant way.
Do you mean we need to enable the caller to deal with get_config
failures (and the transport to relay those failures)? I agree with that.
> > 
> > Cheers,
> > Rusty.
> 
> I agree, but I'd like to point out that even without kmalloc,
> on s390 get_config is blocking - it's waiting
> for a hardware interrupt.
> 
> And it makes sense: config is not data path, I don't think
> we should spin there.
> 
> So I think besides these two parts, we still need my two patches:
>     virtio-balloon: do not call blocking ops when !TASK_RUNNING
>     virtio_console: avoid config access from irq
> in 4.0.
> 
> agree?
I agree that we need those fixes as well.

On Mon, Mar 02, 2015 at 12:31:06PM +0100, Cornelia Huck
wrote:
> On Mon, 2 Mar 2015 12:13:58 +0100
> "Michael S. Tsirkin" <mst at redhat.com> wrote:
> 
> > On Mon, Mar 02, 2015 at 10:37:26AM +1030, Rusty Russell wrote:
> > > Thomas Huth <thuth at linux.vnet.ibm.com> writes:
> > > > On Thu, 26 Feb 2015 11:50:42 +1030
> > > > Rusty Russell <rusty at rustcorp.com.au> wrote:
> > > >
> > > >> Thomas Huth <thuth at linux.vnet.ibm.com> writes:
> > > >> >  Hi all,
> > > >> >
> > > >> > with the recent kernel 3.19, I get a kernel warning
when I start my
> > > >> > KVM guest on s390 with virtio balloon enabled:
> > > >> 
> > > >> The deeper problem is that virtio_ccw_get_config just
silently fails on
> > > >> OOM.
> > > >> 
> > > >> Neither get_config nor set_config are expected to fail.
> > > >
> > > > AFAIK this is currently not a problem. According to
> > > > http://lwn.net/Articles/627419/ these kmalloc calls never
> > > > fail because they allocate less than a page.
> > > 
> > > I strongly suggest you unlearn that fact.
> > > The fix for this is in two parts:
> > > 
> > > 1) Annotate using sched_annotate_sleep() and add a comment: we
may spin
> > >    a few times in low memory situations, but this isn't a
high
> > >    performance path.
> > > 
> > > 2) Handle get_config (and other) failure in some more elegant
way.
> 
> Do you mean we need to enable the caller to deal with get_config
> failures (and the transport to relay those failures)? I agree with that.
We can certainly tweak code to bypass need to kmalloc
on get_config.

Why is it doing these allocs? What's wrong with using
vcdev->config directly?

> > > 
> > > Cheers,
> > > Rusty.
> > 
> > I agree, but I'd like to point out that even without kmalloc,
> > on s390 get_config is blocking - it's waiting
> > for a hardware interrupt.
> > 
> > And it makes sense: config is not data path, I don't think
> > we should spin there.
> > 
> > So I think besides these two parts, we still need my two patches:
> >     virtio-balloon: do not call blocking ops when !TASK_RUNNING
> >     virtio_console: avoid config access from irq
> > in 4.0.
> > 
> > agree?
> 
> I agree that we need those fixes as well.

"Michael S. Tsirkin" <mst at redhat.com>
writes:
> On Mon, Mar 02, 2015 at 10:37:26AM +1030, Rusty Russell wrote:
>> Thomas Huth <thuth at linux.vnet.ibm.com> writes:
>> > On Thu, 26 Feb 2015 11:50:42 +1030
>> > Rusty Russell <rusty at rustcorp.com.au> wrote:
>> >
>> >> Thomas Huth <thuth at linux.vnet.ibm.com> writes:
>> >> >  Hi all,
>> >> >
>> >> > with the recent kernel 3.19, I get a kernel warning when
I start my
>> >> > KVM guest on s390 with virtio balloon enabled:
>> >> 
>> >> The deeper problem is that virtio_ccw_get_config just silently
fails on
>> >> OOM.
>> >> 
>> >> Neither get_config nor set_config are expected to fail.
>> >
>> > AFAIK this is currently not a problem. According to
>> > http://lwn.net/Articles/627419/ these kmalloc calls never
>> > fail because they allocate less than a page.
>> 
>> I strongly suggest you unlearn that fact.
>> The fix for this is in two parts:
>> 
>> 1) Annotate using sched_annotate_sleep() and add a comment: we may spin
>>    a few times in low memory situations, but this isn't a high
>>    performance path.
>> 
>> 2) Handle get_config (and other) failure in some more elegant way.
>> 
>> Cheers,
>> Rusty.
>
> I agree, but I'd like to point out that even without kmalloc,
> on s390 get_config is blocking - it's waiting
> for a hardware interrupt.
>
> And it makes sense: config is not data path, I don't think
> we should spin there.
>
> So I think besides these two parts, we still need my two patches:
>     virtio-balloon: do not call blocking ops when !TASK_RUNNING
I prefer to annotate, over trying to fix this.

Because it's not important.  We might spin a few times, but it's very
unlikely, and it's certainly not performance critical.

Thanks,
Rusty.

Subject: virtio_balloon: annotate possible sleep waiting for event.

CCW (s390) does this.

Reported-by: Thomas Huth <thuth at linux.vnet.ibm.com>
Signed-off-by: Rusty Russell <rusty at rustcorp.com.au>

diff --git a/drivers/virtio/virtio_balloon.c b/drivers/virtio/virtio_balloon.c
index 0413157f3b49..3f4d5acdbde0 100644
--- a/drivers/virtio/virtio_balloon.c
+++ b/drivers/virtio/virtio_balloon.c
@@ -340,6 +340,15 @@ static int balloon(void *_vballoon)
 		s64 diff;
 
 		try_to_freeze();
+
+		/*
+		 * Reading the config on the ccw backend involves an
+		 * allocation, so we may actually sleep and have an
+		 * extra iteration.  It's extremely unlikely, and this
+		 * isn't a fast path in any sense.
+		 */
+		sched_annotate_sleep();
+
 		wait_event_interruptible(vb->config_change,
 					 (diff = towards_target(vb)) != 0
 					 || vb->need_stats_update

On Wed, Mar 04, 2015 at 04:44:54PM +1030, Rusty Russell
wrote:
> "Michael S. Tsirkin" <mst at redhat.com> writes:
> > On Mon, Mar 02, 2015 at 10:37:26AM +1030, Rusty Russell wrote:
> >> Thomas Huth <thuth at linux.vnet.ibm.com> writes:
> >> > On Thu, 26 Feb 2015 11:50:42 +1030
> >> > Rusty Russell <rusty at rustcorp.com.au> wrote:
> >> >
> >> >> Thomas Huth <thuth at linux.vnet.ibm.com> writes:
> >> >> >  Hi all,
> >> >> >
> >> >> > with the recent kernel 3.19, I get a kernel warning
when I start my
> >> >> > KVM guest on s390 with virtio balloon enabled:
> >> >> 
> >> >> The deeper problem is that virtio_ccw_get_config just
silently fails on
> >> >> OOM.
> >> >> 
> >> >> Neither get_config nor set_config are expected to fail.
> >> >
> >> > AFAIK this is currently not a problem. According to
> >> > http://lwn.net/Articles/627419/ these kmalloc calls never
> >> > fail because they allocate less than a page.
> >> 
> >> I strongly suggest you unlearn that fact.
> >> The fix for this is in two parts:
> >> 
> >> 1) Annotate using sched_annotate_sleep() and add a comment: we may
spin
> >>    a few times in low memory situations, but this isn't a high
> >>    performance path.
> >> 
> >> 2) Handle get_config (and other) failure in some more elegant way.
> >> 
> >> Cheers,
> >> Rusty.
> >
> > I agree, but I'd like to point out that even without kmalloc,
> > on s390 get_config is blocking - it's waiting
> > for a hardware interrupt.
> >
> > And it makes sense: config is not data path, I don't think
> > we should spin there.
> >
> > So I think besides these two parts, we still need my two patches:
> >     virtio-balloon: do not call blocking ops when !TASK_RUNNING
> 
> I prefer to annotate, over trying to fix this.
> 
> Because it's not important.  We might spin a few times, but it's
very
> unlikely, and it's certainly not performance critical.
> 
> Thanks,
> Rusty.
> 
> Subject: virtio_balloon: annotate possible sleep waiting for event.
> 
> CCW (s390) does this.
> 
> Reported-by: Thomas Huth <thuth at linux.vnet.ibm.com>
> Signed-off-by: Rusty Russell <rusty at rustcorp.com.au>
> 
> diff --git a/drivers/virtio/virtio_balloon.c
b/drivers/virtio/virtio_balloon.c
> index 0413157f3b49..3f4d5acdbde0 100644
> --- a/drivers/virtio/virtio_balloon.c
> +++ b/drivers/virtio/virtio_balloon.c
> @@ -340,6 +340,15 @@ static int balloon(void *_vballoon)
>  		s64 diff;
>  
>  		try_to_freeze();
> +
> +		/*
> +		 * Reading the config on the ccw backend involves an
> +		 * allocation, so we may actually sleep and have an
> +		 * extra iteration.  It's extremely unlikely,
Hmm, this part of the comment seems wrong to me.
Reading the config on the ccw backend always sleeps
because it's interrupt driven.

This is the relevant code:

static int ccw_io_helper(struct virtio_ccw_device *vcdev,
                         struct ccw1 *ccw, __u32 intparm)
{
        int ret;
        unsigned long flags;
        int flag = intparm & VIRTIO_CCW_INTPARM_MASK;

        do {
                spin_lock_irqsave(get_ccwdev_lock(vcdev->cdev), flags);
                ret = ccw_device_start(vcdev->cdev, ccw, intparm, 0, 0);
                if (!ret) {
                        if (!vcdev->curr_io)
                                vcdev->err = 0;
                        vcdev->curr_io |= flag;
                }
                spin_unlock_irqrestore(get_ccwdev_lock(vcdev->cdev), flags);
                cpu_relax();
        } while (ret == -EBUSY);
        wait_event(vcdev->wait_q, doing_io(vcdev, flag) == 0);
        return ret ? ret : vcdev->err;
}

>		 and this
> +		 * isn't a fast path in any sense.
> +		 */
> +		sched_annotate_sleep();
> +
>  		wait_event_interruptible(vb->config_change,
>  					 (diff = towards_target(vb)) != 0
>  					 || vb->need_stats_update

So the wait_event_interruptible always calls wait_event
which then becomes a busy wait on s390, which is not nice.

So I suspect
http://mid.gmane.org/1424874878-17155-1-git-send-email-mst at redhat.com
is better.

What do you think?

-- 
MST