similar to: bridge sends traffic to all interfaces

Hi, DomU is a Win2008 R2 64 When i install the GPLPV drivers the network latency goes from 15ms to random numbers up to 1200ms and eventually dies. If you run a ping from the DomU to another host the network stays alive but the high latency is still there. Further more if i try and uninstall the network driver i am unable to use the old one (realtek) as it cannot detect the device.

Well, I seem to have developed a strange issue with the GPL PV drivers in Windows. I''m running Xen 3.2 on SLES 10 SP2 and running some Windows XP HVM domUs. Most (12-15) of my Windows machines work just fine. Two of them, though, have started exhibiting a strange behavior with intermittent network connectivity. Basically, the network starts up and connects initially. After some

Hey, everyone, I''m running Xen 3.2 (SLES10) and trying to get an OpenSolaris PV domU to run correctly. I''ve followed a couple of the instruction sets out on the Xen wiki and other folks blogs, but I''m running into an issue with the domU crashing. The OpenSolaris version is the latest development release - 5.11-0.128. The config looks like this:

This may be a better question for the Xen-Devel list, but I''ll start here... Does anyone know if there is any easy way to replace the gPXE ROM with a newer version in Xen? Also, anyone know if there are any plans to have some sort of option in the domU config file to specify a boot rom? Looks like qemu-dm has an "-option-rom" option - is there any way in Xen to make use of

When trying to use the GPL PV drivers with Windows 7 x64 (and testsigning turned on), I get a BSOD with a STOP 0x00000101 error. There''s also an error at the top that says "A clock interrupt was not received on a secondary processor within the allocated time interval." Is this STOP error related to the HPET or other timing adjustments for Xen? Any advice on things I should

I build a DomU kernel on RHEL AS5.1. But when I boot this Guest DomU with the kernel, it gives me error message: Error: (2, ''Invalid kernel'', ''xc_dom_compat_check: guest type xen-3.0-x86_32 not supported by xen kernel, sorry\n'') Can someone give me any suggestion about this problem? Thank you! Joe _______________________________________________ Xen-users

Hi, folks, I''m attempting to run an e-mail server on Xen. The e-mail system is Novell GroupWise, and it serves about 250 users. The disk volume for the e-mail is on my SAN, and I''ve attached the FC LUN to my Xen host, then used the "phy:/dev..." method to forward the disk through to the domU. I''m running into an issue with high I/O wait on the box (~250%)

I''m trying to contain my frustration...but I''m wondering if *anyone* has *ever* gotten the Import functionality to work in XCP? I''ve tried several times, and keep getting the same obnoxious and useless error that is absolutely no help to anyone: Failed to Import. I have made sure that the transfer VM is installed (View -> Show Hidden Objects, transfer VM is there),

I'm attempting to configure Samba with CUPS as a centralized print server. I've done this in the past - my current production server is running Samba 3.2.14. On my current production server, I have several users set up as either "admin users" or "print admin" users so that they can manage the drivers, etc., on the Samba server. In setting up my new server, I'm

Hi! Anyone have a suggestion which version of Linux would be the best host? We typically use Ubuntu but we are flexible since we want the best performance and the least amount of headaches getting it installed and working. Thanks, Jimmy _______________________________________________ Xen-users mailing list Xen-users@lists.xensource.com http://lists.xensource.com/xen-users

Well, now that I''ve figured out that network booting XCP is not really going to be feasible, I''m moving on to my next option: flash media installation. The systems that I purchased have SDHC slots on them, so I figured I''d attempt to install XCP to one of these cards. I had already read that there''s a minimum disk size in the installer (apparently 12 GB in

Hi, I am trying to (live-)migrate a paravirtualized machine from hosta to hostb: -----8<---- hosta:~ # xm list pvm Name ID Mem VCPUs State Time(s) pvm 64 384 1 -b---- 0.5 hostb:~ # xm list pvm Error: Domain ''pvm'' does not exist. hosta:~ # xm migrate pvm 192.168.0.2 Error:

Hi, I am trying to install openxencenter to control my VMs I followed the instructions but when I tried to start it I got:  File "window.py", line 44, in <module>     import gtkvnc ImportError: No module named gtkvnc does any one face this problem before. I tried to comment the import line and xencenter started but console tab is not working and it is lookoing for gtkvnc module.

I''m running xen on SLES10SP2. It''s been much more stable than SP1, but I still occasionally have issues. For example, one of my servers (8 CPU/32GB RAM) has five sles pv domUs and five fully virtualized windows 2k3 domUs. It had been up for almost 60 days. Yesterday afternoon one of the sles domU''s stopped responding. I went to check on it and I couldn''t using

In my experiments with setting up a NAS as a VM, I can only successfully import three drives; the root drive, the cd and one more. However, I have plenty that I want to use: disk=[''file:/vserver/vm_disks/Patch.disk.xm,hda,w'', ''phy:/dev/sda,ioemu:hdd,w'', ''phy:/dev/sdb,ioemu:hde,w'', ''phy:sdc,ioemu:hdf,w'',

After upgrade via http://download.opensuse.org/repositories/Virtualization:/openSUSE11.3/openSUSE_11.3/src/xen-4.0.1_21326_01-1.1.src.rpm with any "kotd" or 2.6.34.4-2.2-xen VFB gets broken . It worked with original  Xen 4.0, no matter of  some additional patching to support ZFS 24 has been done and 4.0 src.rpm has been rebuilt to reinstall 4.0   In particular,  virt-install fails to

I''m running SLES10 SP1 and have been using file:/ for my file-backed domUs. The domUs sit on a shared OCFS2 SAN-backed filesystem and are run on my three or four XEN servers. I''m having issues with the loopback devices not being released when the domUs shutdown or migrate, so I decided to switch over to tap:aio for my file-backed domUs. This isn''t working, either.

I''m using Xen with SLES10 and am using NPIV to attach FC SAN disks to my domUs. I''ve resize one of the disks on my SAN and I''m wondering if there''s a way to force Xen to rescan/resize the block device without shutting down the domU or unmounting the volume. Thanks, Nick -------- This e-mail may contain confidential and privileged material for the sole use

I just ordered quite a few servers, and, without verifying ahead of time, ordered without hard drives planning to boot over iSCSI using the built-in network cards (NOT an iSCSI HBA). I''m wondering if anyone has tried (and hopefully succeeded) installing XCP to an iSCSI volume using a network card with iSCSI boot support and the software iSCSI initiator in XCP. Obviously I can order HDs

So, I made a mistake a bought four systems with the Intel Core i3 processors, without doing my homework to make sure that these systems actually supported VTd. Turns out there''s plenty of information out there indicating that the Core i3 processors do *not* support VTd. I was counting on VTd for two applications: Graphics Passthrough and passing through a PCIe 4-port serial card. Of