similar to: M2N32, suse 10.3 and network problem

Hi, once again, Problems with pciback and pci passthrough the system -------------------------------------------------------------------------------- DOMAIN0:~# lspci -tv -[0000:00]-+-00.0 nVidia Corporation nForce3 250Gb Host Bridge +-01.0 nVidia Corporation nForce3 250Gb LPC Bridge +-01.1 nVidia Corporation nForce 250Gb PCI System Management +-02.0

I've got a Digium PCI telephone card that I'm trying to use with an AsteriskNow guest, on a CentOS 5.2 host. I've tried setting up the pciback stuff, and think I've done it right, but the card does not show up in the guest. I'm obviously missing something, so any help (including ways to debug this!) would be greatly appreciated. Here's some more info: The guest is

I am a bit confused on the PCI stuff. PASSTHRU-- does this mean that pcifront is not needed? Or only that the PCI is not limited as it is with slot. In general, none of the docs are getting me anywhere with xen 3.0.3. Example: I run this: echo -n 0000:2:0.1>/sys/bus/pci/drivers/pciback/new_slot echo -n 0000:2:0.0>/sys/bus/pci/drivers/pciback/new_slot echo -n bind 0000:2:0.0 >

Hi, I have a PC with 3 ethernet interfaces. I am trying to a) assign 2 ethernet interfaces exclusively to one domU by using the late binding method and b) to use a bridge between the third interface and dom0 (that works fine). The goal is to not to have to use bridges for the exclusively assigned interfaces. Is it possible? (If not, no need to read the rest) The problem I have is that I

I am using the latest xen unstable and trying to install this 00:19.0 Ethernet controller: Intel Corporation 82562V 10/100 Network Connection (rev 02) since xen uses 2.6.16.29 it does not support it yet, someone said (on google) that 2.6.18.3 supports it. So I want to boot 2.6.18.3 in domU and enable it with the pciback thing. my seize commands are: echo -n 0000:00:19.0 >

Hello, I´m trying to map one network interface of a Dual-Port e1000 Server Adapter to a DomU (firewall). In Dom0 the adaper is seen with lspci as: 06:00.0 Ethernet controller: Intel Corporation 631xESB/632xESB DPT LAN Controller Copper (rev 01) 06:00.1 Ethernet controller: Intel Corporation 631xESB/632xESB DPT LAN Controller Copper (rev 01) My goal is to map only 06:00.1 to DomU so I used this

Trying to set up PCI pass through with xen 3.2.1 on Debian Lenny, with xen Kernel 2.6.26... having no luck. I have the following configured... i) Virtualization and vt-d are both enabled in the bios, I have power cycled after making these changes. ii) I have these option in grub menu; iommu=1 pciback.permissive pciback.hide=(07:01.0)(01:00.0) vtd=1 iii) I have this in my cfg file

Hello everybody, for just one week I try to install three servers on an OpenSuSE 10.3 dom0 equipped with 4 NICs. One server is an OX using the onboard NIC via xenbr0. This server runs!! For my IPCop server I intended to use the three remaining NICs (Intel Pro100/S, 3Com 3C590, Realtek RTL-8139). These three NICs should be used natively by my IPCop. So I tried to use the pciback driver. I wrote a

Hello, I''m trying to do a pci passthrough for a perc 5/i raid controller and i have 2 problems (i haven''t used linux systems recently so i may be a bit rusty) : On the hardware part i''m using an ASUS M4A89TD PRO motherboard with iommu enabled in bios (and i can see with "xm dmesg" that I/O Virtualization seems enabled by xen). On the software part i

I''ve been trying to set up a VGA-passthrough on my Ubuntu 12.04 box to run Windows (for gaming) while leaving my RAID-5 array available (managed by Linux). First, here are the machine specs: CPU: AMD A8-3870K 3.4GHz Quad-Core APU GPU: APU-integrated AMD Radeon 6550 (shared memory) Mobo: ASUS F1A75-V EVO with AMD-virtualization enabled in UEFI-BIOS RAM: 8GB DDR3 1866 G-Skill Sniper

Hi. Im faced with a little problem when trying to give an Ali USB 2.0 controller to a guest system: when i try to start my domu, it says that the backend device could not be found. Im using Debian etch both as dom0 and as domU. Im using the standard binary installation from the Debian etch repositority tree (kernel, hypervisor, ...). Im running xen 3.0.3-1 and both use a 2.6.18 kernel. In

Hi! As dom0 I''m running Ubuntu Hardy withe xen 3.3 from backports. Reason to using xen 3.3 is that I could get Intrepid stock kernel to work as domu with xen 3.2. Now the problem I have is that I can''t passthrough PCI-devices to my domu. If I run lspci in the domu nothing is returned. I''ve tried to use the kernel from Hardy (2.6.24-21-xen) and stock kernel from

Hi all! I want to assign a physical network card (e100) to a domU: I think Dom0 is ok but domU does not recognize the pci nic. into DomU I don''t know wath should I see: I have nothing in dmesg nor in messages... Into Dom0 I have this modules.conf: options pciback hide=(0000:03: 08.0) install e100 /sbin/modprobe pciback; /sbin/modprobe --ignore-install e100 This is dmesg: pciback

On 3/22/23 04:23, nospam at godawa.de wrote: > Jim Fehlig schrieb: >> >> What is the libvirt version? > > It's the "latest and greatest" I get from this source: > > [root at xen1 ~]# virsh --version > 6.6.0 > > [root at xen1 ~]# libvirtd --version > libvirtd (libvirt) 6.6.0 > > [root at xengfs1f ~]# yum list | grep libvirt >

Hi there, After updating a server from CentOS 5.3 to 5.4 my Xen pci-passthru setup has some troubles. The server has two NICs, one used by dom0 and the other assigned to a domU and one SCSI controler assigned to another domU. It has been working fine since CentOS 5.1, when I did the initial setup. After upgrading to 5.4, I get this error when starting the domU with one of the NICs assigned:

Thanks to the kind person(s) who worked on this. I am using PCI passthrough right now and it works. I hope support is added for VT domains too; That would be extremely useful. So far I have tried a NIC, USB, and PCI Video. The NIC works flawlessly. USB works as long as the devices are present at the time the domain is started. Hotplugging USB devices seems not to work. If I open

Hi All, Please help me. I am now installing the XEN on my PC and trying to config the pci pass through. My motherboard is intel DQ45CB which is vtd enabled. I downloaded the latest xen4.0 source from xen.org which is the latest release. I downloaded stable-2.6.32-x dom0 kernel source from jeremy''s repository. After compiling the xen and dom0 kernel, I could play it. I could create

Hi All, Please help me. I am now installing the XEN on my PC and trying to config the pci pass through. My motherboard is intel DQ45CB which is vtd enabled. I downloaded the latest xen4.0 source from xen.org which is the latest release. I downloaded stable-2.6.32-x dom0 kernel source from jeremy''s repository. After compiling the xen and dom0 kernel, I could play it. I could create

Dear all, i''m having problems passing a Hauppage Nova-S2 card to my DomU (Mythtv Backend). Hardware is: HP XW8200 2x 3.0GHz Xeon 8Gb ECC Ram 1x TT3200-S2 card 1x DVBWordl S2 card 1x Nova-S2 card [many other card for other domUs...] Dom0 is Ubuntu 8.04 server LTS. Xen 3.2 from repo. DomU (Mythtv) is a 8.04 (using LVM) both using 2.6.24-23-xen kernels Dom0 configs: lspci: ... 02:01.0

Hi all, did somebody successfuly export ISDN Cards to DomU? I want to have 2 ISDN Cards in DomU (for Asterisk with mISDN) lspci -vt -[0000:00]-+-00.0 nVidia Corporation MCP55 Memory Controller +-01.0 nVidia Corporation MCP55 LPC Bridge ... +-05.1 nVidia Corporation MCP55 SATA Controller +-06.0-[0000:01]--+-00.0 Cologne Chip Designs GmbH ISDN