similar to: domU with gigabit ethernet or recommendations?

Dear Samba- We're using the virtualization application openVZ to run small web services for researchers. Unlike other virtualization software, openVZ uses the host file system for the guest OS; essentially the root file system of the guest is a chrooted subdirectory on the host. When openVZ migrates a guest between two host machines it uses rsync to transfer the files. Unfortunately, this

Hi, I have installed samba on a dell poweredge server. It uses integrated NetXtreme II BCM5708 Gigabit Ethernet card. My issue is that i am getting extremely slow speeds (about 1.2MB/s) on the gigabit network from linux as well as windows clients using when reading from the samba share. On the same setup (same server, client, network) using scp,rsync,nfs gives me anything between 35-50 MB/s. So

So I just finished doing a fresh install of CentOS 6.3. The machine has three ethernet ports in it: one on the motherboard (VIA Rhine), and two add-on cards, an Intel Pro100 and an old SMC1255TX. When CentOS comes up, this is what I see in the dmesg output: # dmesg | grep eth e100 0000:00:08.0: eth0: addr 0xf6043000, irq 16, MAC addr 00:02:b3:be:02:87 eth1: ADMtek Comet rev 17

Does anyone have some tips for setting up Broadcom's 802.3AD support or just getting their driver compiled / installed? First off, I noticed redhat claims the broadcom bcm5708 driver has been added to the rhel4 kernel. But I don't see /proc/net/nicinfo which broadcom claims the driver creates when it's successfully initialized. So, I'm trying to build the driver based on the

Hi, I would like to ask concerning problems after installing xen 3.3 on Centos 5.2 I use 2.6.18.8-xen (xen3.3.1 testing - installing with mercurial). After done with make world and make install, I did mkinitrd and placing it in /boot changing the grub and reboot.. succeded I do not install libvirt and the domUs from the previous xen 3.0 (built-in Centos 5.2) are NOT able to start : [root@wing

Hi Folks, Is there any SIP FXS ATA with Gigabit ethernet bridge port, in the market ? -- Isamar Maia Cel. VIVO SSA: (55) 71-9940-2012 Cel. TIM SSA: (55) 71-9289-5128 Cel. Claro SSA: (55) 71-9146-8575 Fixo: (55) 71-4062-8688 Skype ID: isamar.maia "A vida ? muito curta para ser pequena" (Benjamin Disraeli) -------------- next part -------------- An HTML attachment was

Hi all I'm trying to setup second ethernet on Dell 2950 server but there isn't any eth1 device (in the bios are ON) # dmesg |grep eth eth0: Broadcom NetXtreme II BCM5708 1000Base-T (B2) PCI-X 64-bit 133MHz found at mem f8000000, IRQ 169, node addr 001c23d878bb eth1: Broadcom NetXtreme II BCM5708 1000Base-T (B2) PCI-X 64-bit 133MHz found at mem f4000000, IRQ 169, node addr 001c23d878bd

Hi, I hope someone can help me, I cannot seem to get a system's ethernet interface to correctly work in promiscuous mode... I have a Centos 6.4 system with 2 bnx2 interfaces on it. I have set up eth1 in promiscuous mode and am sending traffic to it using the port mirroring configuration on a Nortel 3510-24T switch. The switch reports that it is sending a fair amount of traffic to the

I am posting the message below again because it did not go through last night. Help! Steve Timm -- ------------------------------------------------------------------ Steven C. Timm, Ph.D (630) 840-8525 timm@fnal.gov http://home.fnal.gov/~timm/ Fermilab Computing Division, Scientific Computing Facilities, Grid Facilities Department, FermiGrid Services Group, Assistant Group Leader.

Hi, After changing cables,switches,ports, I came to the conclusion that bce is reporting input errors that are not there, or creating them. I checked this with 3 different boxes, all Dell-2950/Broadcom NetXtreme II BCM5708 1000Base-T (B2), and one of them, while running Solaris, reported 0 errors after a week, and freebsd after a few minutes its count was > 100. The errors appear under

host and guest both centos 5.5 network is 192.168.62.40 host is setup as follows [root at cloud2 ~]# ifconfig br0 Link encap:Ethernet HWaddr 00:1A:64:12:10:D9 inet addr:192.168.62.199 Bcast:192.168.63.255 Mask:255.255.254.0 inet6 addr: fe80::21a:64ff:fe12:10d9/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:1705488

Hi, I have a Dell PowerEdge 1950 with two NICs Broadcom NetXtreme II BCM5708 1000Base-T. I installed CentOS 5.1 and Xen 3.0.3 (RPM). One of my virtual machines has Windows 2003 Server. In this virtual machine my NICs appears like "Realtek RTL8139 Family PCI Fast Ethernet NIC". The problem is that when I ping to other machines sometimes the reply time value is very high: C:>

Hello, Marvel Yukon Gigabit Ethernet is supported by CentOS ? -- -- Devel in Precio http://www.pas-world.com

I can not disable the auto-negotiation (eth1) on my centos 6.2 via ethtool or /etc/sysconfig/network-scripts/ifcfg-eth1 the eth1 is a private network on a cheap gigabit-switch (under controll from a serverhoster). sometime the ethernet-card lost the "speed" and "duplex" information and change it to "unknown". i can only fix this with a network-restart (or

Hello, My computer locked up and I had to press the reset button. Ever since then I can''t mount the btrfs filesystem, here''s the output: [ 37.645583] ------------[ cut here ]------------ [ 37.645598] WARNING: at fs/btrfs/free-space-cache.c:1887 btrfs_remove_free_space+0x329/0x350 [btrfs]() [ 37.645600] Modules linked in: btrfs zlib_deflate libcrc32c ext4 jbd2 mbcache crc16

Bernard Łabno wrote: > Hello, > What does this line mean : > > HTB: quantum of class 10200 is small. Consider r2q change. > > > And how should I fix it ? I have dsl 1mb connection and 2 cards > (realtek-8139C and realtek-8100B/8139D) > > Could the above line cause this ? : > NETDEV WATCHDOG: eth0: transmit timed out > eth0: Transmit timeout, status 0c 0005

Hi all, I have a Debian Lenny domU running on an Etch dom0 (xm info output below). It seems that the domU network falls asleep after some time. After some activity, either trying to do something like a ping or dig from within the domU or enough client attempts to connect to a samba share, it comes back up. That wouldn''t be terrible, except that the delays in reconnecting to the samba

Hi, tuning my network fixing nic's speed and duplex (both on server and switch) i got this error with bce driver: # ifconfig bce0 bce0: flags=8843<UP,BROADCAST,RUNNING,SIMPLEX,MULTICAST> metric 0 mtu 1500 options=1bb<RXCSUM,TXCSUM,VLAN_MTU,VLAN_HWTAGGING,JUMBO_MTU,VLAN_HWCSUM,TSO4> ether 00:15:c5:fe:11:01 inet 192.168.1.13 netmask 0xffffff00 broadcast

For an office that is using VoIP phones to connect to Asterisk, is gigabit ethernet really necessary for the Asterisk box to connect to the switch? I know that I won't even approach the limits of 100 Mbps, but would gigabit help with latency / collisions when several calls are underway? The fact is, anything going outside the office will be over a data T1, so intuition tells me that 100

Hi all, I have a problem when from domU I need to configure a network interface. My system configuration is the next: dom0: xen 3.4.3 with 2.6.18-238.9.1.el5xen kernel, making pci back from a network card. All ok. This is the result from "lspci -v -s 09:00.0" 09:00.0 Ethernet controller: Broadcom Corporation NetXtreme II BCM5708 Gigabit Ethernet (rev 12) Subsystem: Broadcom