similar to: OCFS2 1.4 + DRBD + iSCSI problem with DLM

All, We are having some problems getting OCFS2 to run, we are using kernel 2.6.15 with OCFS2 1.2.1. Compiling the OCFS2 sources went fine and all modules load perfectly. However, we can only mount the OCFS2 volume on one machine at a time, when we try to mount the volume on the 2 other machines we get an error stating that another node is heartbeating in our slot. When we mount the volume

Ubuntu 14.04, drbd Hi On a drbd Primary node, when attempting to mount our cluster partition: sudo mount -t ocfs2 /dev/drbd1 /cluster we get: mount.ocfs2: Unable to access cluster service while trying to join the group We then call: sudo dpkg-reconfigure ocfs2-tools Setting cluster stack "o2cb": OK Starting O2CB cluster ocfs2: OK And all is well: Aug 22 13:48:23 uc1 kernel: [

Hello, I have one cluster drbd8+ocfs2. If I mount ocfs2 partition on node1 it's work but when I mount partition on node 2 I receive in /var/log/messages this -Mar 5 18:10:04 suse4 kernel: (2857,0):o2hb_do_disk_heartbeat:665 ERROR: Device "drbd1": another node is heartbeating in our slot! -Mar 5 18:10:04 suse4 kernel: WARNING: at include/asm/dma-mapping.h:44 dma_map_sg() -Mar 5

Hi everyone; I have a problem on my 10 nodes cluster with ocfs2 1.2.9 and the OS is RHEL 4.7 AS. 9 nodes can start o2cb service and mount san disks on startup however one node can not do that. My cluster configuration is : node: ip_port = 7777 ip_address = 192.168.5.1 number = 0 name = fa01 cluster = ocfs2 node: ip_port =

Dear all, I have sent this problem earlier but maybe its not detail, here I try to write more detail. I hope anybody can help me to point out the problem. First of all I used Ubuntu 12.04 x64 both for domain0 and domainU with modification to run under xen hypervisor and work with remus. I follow and configured the remus with this notes

Hi , I am getting the error "No space left on device" on a device with free space which is ocfs2 filesystem. Additional information is as below, [root at sai93 staging]# debugfs.ocfs2 -n -R "stats" /dev/sdb1 | grep -i "Cluster Size" Block Size Bits: 12 Cluster Size Bits: 15 [root at sai93 ~]# cat /etc/redhat-release Red Hat Enterprise Linux Server release

Hello, I have an active, balanced webcluster with 2 SLES10SP2 nodes, both running ocfs2 with an iscsi target. The ocfs2 volume is mounted on both nodes. Everything works fine, except sometime the load on both systems go as high as 200, then both systems freeze, only reboot helps to regain control. I noticed that this behaviour does not occur when the cluster is NOT balanced. When the load on both

I think I might have miss understood where it is failing, has this file been added to the DB on the web site or does it fail when you try to onfigure this? Carle Simmonds Infrastructure Consultant Technology Services Experian UK Ltd __________________________________________________ Tel: +44 (0)115 941 0888 (main switchboard) Mobile: +44 (0)7813 854834 E-Mail: carle.simmonds at uk.experian.com

I have installed OCFS2 on two nodes SuSE 10. Seems all works superb and nice from the first sight. But, /dev/sda ocfs2 rac1 is not sharing through net (port 7777) with rac0. On both nodes I have 500Mb /dev/sda disks that are mounted (and are ocfs2). But they did not share the content with each other (files and folders in it). So when I am creating the file in one node I am expecting to

Hallo, I have two servers and both are connected to external array, each by own SAS connection. I need these servers to work simultaneously with data on array and I think that ocfs2 is suitable for this purpose. One server is P4 Xeon (Gentoo linux, i386, 2.6.22-r2) and second is Opteron (Gentoo linux, x86_64, 2.6.22-r2). Servers are connected by ethernet, adapters are both Intel

Hi. I'm pretty new to ocfs2 and clusters. I'm trying to make ocfs2 running over a drbd device. I know it's not the best solution but for now i must deal with this. I set up drbd and work perfectly. I set up ocfs and i'm not able to make it to work. /etc/init.d/o2cb status: Module "configfs": Loaded Filesystem "configfs": Mounted Module

I have a setup with lot's of small files (Maildir), in 4 different volumes and for some reason the volumes are full when they reach 60% usage (as reported by df ). This was ofcourse a bit of a supprise for me .. lots of failed writes, bounced messages and very angry customers. Has anybody on this list seen this before (not the angry customers ;-) ? Regards, =paulv # echo "ls

Hi, I have installed and configured ocfs2 as per the given guidelines on two nodes. The output of the service status of o2cb and ocfs2 is as under: Node: rashida1 -------------------------------------------------- [root at rashida1 ~]# service o2cb status Driver for "configfs": Loaded Filesystem "configfs": Mounted Driver for "ocfs2_dlmfs": Loaded Filesystem

I looked around, found older post which seems not applicable anymore. I have a cluster of 2 nodes right now, which has 3 OCFS2 file systems. All the file systems were formatted with 4 node slots. I added the two news nodes (by hand, by ocfs2console and o2cb_ctl), so my /etc/ofcfs/cluster.conf looks right: node: ip_port = 7777 ip_address = 192.168.201.1 number = 0

I have a relatively new test environment setup that is a little different from your typical scenario. This is my first time using OCFS2, but I believe it should work the way I have it setup. All of this is setup on VMWare virtual hosts. I have two front-end web servers and one backend administrative server. They all share 2 virtual hard drives within VMware (independent, persistent, &

hi there i try to setup OCFS2 with loop device /dev/loop0 i've 4 servers running SLES10 SP2. internal ip's: 192.168.55.1, .2, .3 and .6 my cluster.conf: -------------------------------------------- node: ip_port = 7777 ip_address = 192.168.55.1 number = 0 name = www cluster = cawww node: ip_port = 7777 ip_address = 192.168.55.2

Hi, I am trying to configure a two node cluster on SLES10SP2 using user level heartbeat. Here is my configuration. ocfs2-tools-1.4.0-0.3 **user level heartbeat** -> lsmod | grep ocfs ocfs2_user_heartbeat 20992 1 ocfs2_dlmfs 37776 1 ocfs2_dlm 204456 1 ocfs2_dlmfs ocfs2_nodemanager 223384 6 ocfs2_user_heartbeat,ocfs2_dlmfs,ocfs2_dlm configfs 44700 3 ocfs2_user_heartbeat,ocfs2_nodemanager

Dear All, Currently using RHEL6 Linux and Kernel Version is 2.6.32-71.el6.i686 and DRBD Version is 8.3.10 DRBD is build from source and Configured DRBD with 2 Node testing with Simplex Setup Server 1 : 192.168.13.131 IP Address and hostname is primary Server 2 : 192.168.13.132 IP Address and hostname is secondary Finally found that drbd0, drbd1 mount failed problem *Found some error messages

Hi, First of all, I'm new to ocfs2 and drbd. I set up two identical servers (Athlon64, 1GB RAM, GB-Ethernet) with Debian Etch, compiled my own kernel (2.6.16.20), then compiled the drbd-modules and ocfs (modules and tools) from source. The process of getting everything up and running was very easy. I have one big 140GB partition that is synced with drbd (in c-mode) and has an ocfs2

Does anyone have any idea what to try next? Here are the steps I have taken and the problem: (I wanted to post my question on the first line before I explained the problem and what I have tried) ---------- Node 0 has the file system mounted just fine and works great. When trying to mount on Node 1: `mount.ocfs2 /dev/mapper/data /cluster/ data` I get this error after about 30 seconds: