similar to: centos 5.3 upgrade and duplicate processes running

Hi, I just upgraded to CentOS 5.3 last night and see these duplicate commands (migration/0, migration/1) when running top -c? Is this normal? If not, how do I fix it to make only one command show up? 1 root 15 0 2064 592 512 S 0.0 0.0 0:03.40 init [3] 2 root RT -5 0 0 0 S 0.0 0.0 0:00.00 [migration/0] 3 root 34 19 0 0 0 S 0.0 0.0 0:00.00 [ksoftirqd/0] 4 root RT -5 0 0 0 S 0.0 0.0 0:00.00

Hello, I was wondering if anyone could tell me why so many processes are started on my system? Here is a list of them. I am trying to figure out why they are running and if I can stop them. Thnx. USER PID %CPU %MEM VSZ RSS TTY STAT START TIME COMMAND root 2 0.0 0.0 0 0 ? S< 19:33 0:00 [migration/0] root 3 0.0 0.0 0 0 ? SN 19:33 0:00 [ksoftirqd/0]

Hi 2 all ! I have problems with concurrent filesystem actions on a ocfs2 filesystem which is mounted by 2 nodes. OS=RH5ES and OCFS2=1.2.6 F.e.: If I have a LV called testlv which is mounted on /mnt on both servers and I do a "dd if=/dev/zero of=/mnt/test.a bs=1024 count=1000000" on server 1 and do at the same time a du -hs /mnt/test.a it takes about 5 seconds for du -hs to execute: 270M

I am running centos 4.2 on a P4 3 GIG with 2 GIG ram. This machine has been fine for months. my laptop is fine. X is taking 99 percent of the cpu after some time. All I was doing was editing code. If I killall -9 X it comes back for a while then maxes out again. Any ideas on something to tweek??? THanks, jerry ------------ Tasks: 120 total, 2 running, 118 sleeping, 0 stopped, 0 zombie

I have a server holding a 2.5-4.0 load level consistently, where should I start debugging it? top - 13:32:01 up 167 days, 5:45, 6 users, load average: 2.87, 1.83, 1.51 Tasks: 111 total, 1 running, 110 sleeping, 0 stopped, 0 zombie Cpu(s): 0.0% us, 0.0% sy, 0.2% ni, 99.8% id, 0.0% wa, 0.0% hi, 0.0% si Mem: 895728k total, 871996k used, 23732k free, 190612k buffers Swap:

I'm seeing some strange results from top on CentOS 4.0. When it first starts, it reports low CPU usage. The next refresh (and subsequent) refreshes, it shows high CPU usage. In both cases, there is nothing shown in the process list that is using much CPU. What is causing this? Here is some truncated output from a single run of "top -b -n 2":

Over the past few months, I have seen many postings here about runaway smbd processes with Samba versions 3.0.20 and above. Personally, it never happened to me until today. Also, I have stuck with Samba 3.0.13 on most of my machines because of THIS reported issue and a couple of other issues that I have experienced. However, I have a machine running RIGHT NOW where smbd has gone out of

I have Cent OS 5.1 I also have http://phpsysinfo.sourceforge.net/ I have asterisk running . Now when I look at System Information , I see that "Physical Memory" keep increasing and at one point it reaches 96%. Then my sever get hang and then I have to restart it. I have 4 GB RAM. Processors 2 Model Intel(R) Core(TM)2 Duo CPU E7200 @ 2.53GHz CPU Speed 2.53 GHz Cache Size 3.00 MB

Hi Team Can someone advice me on how i can lower the load average on my asterisk server? dahdi-linux-2.1.0.4 dahdi-tools-2.1.0.2 libpri-1.4.10.1 asterisk-1.4.25.1 2 X TE412P Digium cards on ISDN PRI Im using the system as an IVR without any transcoding or bridging ************************************** top - 10:27:57 up 199 days, 5:18, 2 users, load average: 67.75, 62.55, 55.75 Tasks: 149

Hi All, I''ve got a DomU that sometimes goes mad. I can''t ssh or usually even console to it. The time I did manage to console I got a load of dumps about being out of memory and swap, but couldn''t run any commands to find out which process had gone mad :( From Dom0 I can see the DomU at 100% CPU and can only stop it with a destroy. What can I do/check to find

System requirements for CentOS 5 minimal installation (console and ssh) are....128 MB ram, 256...? I can't find this information in rhel5 installation manual.

Hi, Is there any news about CentOS 5.2 updating to php 5.2? Best Regards, Melinda Odom Design Hosting, Inc. Web Design, Web Hosting, & Ecommerce Solutions 479-471-0891 CST info at designhosting.biz http://www.designhosting.biz

Hello List, how much run should i give xen0 if the only service that runs is sshd ? ~# free              total       used       free     shared    buffers     cached Mem:        127032     124952       2080          0       7776      89688 -/+ buffers/cache:      27488      99544 Swap:      1048816          0    1048816 Tasks:  33 total,   2 running,  31 sleeping,   0 stopped,   0 zombie

Dear List Users Greetings, i have come across the problem where CentOS 6.3 x64 has more than 700 processes running. i am not sure where to start, what in normal or abnormal. [root at jet]# ps -A PID TTY TIME CMD 1 ? 00:00:03 init 2 ? 00:00:00 kthreadd 3 ? 00:00:00 migration/0 4 ? 00:00:00 ksoftirqd/0 5 ? 00:00:00 migration/0 6

Hi, Which one of these listings would I put in my yum.conf file to upgrade my centos 3.6 to centos 4.2? http://mirror.centos.org/centos/4.2/os/ alpha or ppc? Sincerely, Melinda Odom www.designhosting.biz 479-471-0891 -- No virus found in this outgoing message. Checked by AVG Free Edition. Version: 7.1.385 / Virus Database: 268.5.0/325 - Release Date: 4/26/2006 -------------- next part

Hi, on my c6.3 server (guest of a vmware host) I have a strange load average value: w command: > [root at s-doc ~]# w > 11:19:23 up 41 days, 23:15, 1 user, load average: 4,03, 4,03, 4,00 > USER TTY FROM LOGIN@ IDLE JCPU PCPU WHAT > root pts/2 dodo:S.0 11:15 0.00s 0.02s 0.00s w top command: > top - 12:13:31 up 42 days, 9 min, 1

Hi, I have plesk server administration 7.5.4 on my server and am wanting to upgrade to plesk 8. Plesk 8 supports Centos 4.2 and the notes on the 4.2 readme say: http://mirror.centos.org/centos/4.2/readme If you know what you are doing, and absolutely want to remain at the 4.2 level, go to http://vault.centos.org/ for packages. If you follow the other link listed in that doc it goes to the

Hi, I am running centos 4.2 version on my server. The /etc/redhat-release file lists centos 4.4 (final). In my Plesk server administration it also shows centos 4.2. I need to upgrade plesk and am suppose to have centos 4.3 to do this upgrade. In the past I have run "yum update" and the OS was always updated to the next version but this no longer works on my server. When I try yum

>>> I have ecommerce stores on my server who use the same instantssl certificate without any problems. These particular certificates were migrated over from one plesk system to my new server with centOS 3.4 and plesk 7.5.1 reloaded. >>> We got it working. It was a custom config problem for that one site. Sincerely, Melinda Odom www.designhosting.biz 479-471-0891

Hi, I am using CentOS 3.5 plus the Plesk reloaded 7.3 server admin and just recently did a small upgrade of some plesk packages plus the update from CentOS 3.4 to 3.5. It seems that all of my forms have stopped working using nms FormMail.pl script. Everything was working before these last two updates. I have debug set on the form script and it does work without any errors but I never get the