similar to: [Bridge] Problem with Routed mode using br2684ctl tool

Hi,All I am using iproute2 to manage bandwith for ADSL router.High,medium,low priority are needed for different protocol port on the ADSL's upstream side,as following: LAN --- |ADSL Router|------WAN When there aren't traffic on the specific priority, its bandwidth should be borrowed by other priorities.But it doesn't work.Here is my script: /usr/sbin/tc qdisc del dev nas0 root

Hello, I am wondering if any of you knows how to add BR2684-rt nas interfaces into a Ethernet bridge, I know that brctl will work with BR2684-br, but not for BR2684-rt. Many thanks! Hai -------------- next part -------------- An HTML attachment was scrubbed... URL: http://lists.linux-foundation.org/pipermail/bridge/attachments/20070307/392c8ffd/attachment-0002.htm

Hello all, Does anyone know of a methodology to build a route based on the inbound and outbound interfaces as opposed to ip addresses? We are essentially trying to forward packets from one interface to another without looking at the ip address. Bridging (brctl, br2684ctl) will not work in this case as the interfaces use different layer 2 encapsulation (e.g., atm0<=>eth0, or

Hi,All I use HTB to control traffic.Here is my script: /usr/sbin/tc qdisc del dev nas0 root /usr/sbin/tc qdisc add dev nas0 root handle 1:0 htb default 60 /usr/sbin/tc class add dev nas0 parent 1:0 classid 1:1 htb ceil 896kbit rate 896kbit prio 0 burst 60k /usr/sbin/tc class add dev nas0 parent 1:1 classid 1:10 htb ceil 896kbit rate 537kbit prio 1 burst 60k /usr/sbin/tc class add dev

Hello LARTC, Internet connection - ADSL, interface nas0 (115kbit guarantied, up to 1mbit possible. Depends on ISP load, impossible to guess). Internal interface LAN, eth0. Is it possible to successfully shape download traffic on eth0 using HTB? Classes must have guarantied rate calculated from 115kbit possible rate (for example 3 classes) and the possibility to borrow up to 1mbit (depends on ISP

Hi, I find this diagram which details the kernel packet traveling : http://www.docum.org/docum.org/kptd/ Is it up to date ? I made some test and I put a DNAT rules in the PREROUTING table of an interface and I attach it a ingress policy, the dst IP wasn''t changed. the DNAT it isn''t yet make. I''ve another question (I''m not sure is it the good mailing list), for

Hi, I would like to make a QoS configuration on a linux based dsl router. It is for a server, so I want to shape outgoing traffic, incoming traffic should not be a problem as long as I have a quite assymetric connection. I would like to achieve the following goals: 1) To have one class (p2p) having all the available bandwith if there is no activity on other classes. 2) If another class (ftp

Hi people I''m new to the mailing list, but I''ll save my presentation to another mail as I already have some strong questions. Now I just faced this mail that arose me a question I had when "installing" my qos. > Internet connection - ADSL, interface nas0 (115kbit guarantied, up to 1mbit possible. Depends on ISP load, impossible to guess). > Internal interface

Hi Maarten, Yes, I'm behind ADSL with PPPoE but I don't think it is related with my case. When my client disconnects from IceCast server for 15-20 seconds, my active downloads are not interrupted. It currently effects only the route to my IceCast server, other routes looks uneffected. I'm pinging IceCast server continuously and checking trace route periodically. It is comething like:

Anyone know if it''s possible to interleave two IP packets when using PPPoA and VC based lines? Can it be done with any PPPoE implementations? The goal is to reduce the delay when you have a high priority packet waiting, but a lower priority (large) packet already started going out ahead of this packet. I don''t want the overhead of much smaller MTU, which is the other way

Hi Tom, You might be right, but I don't get why my existing downloads (I guess they are on different routes) are not affected. If my ADLS provider is doing some IP adjustments (btw my IP is static) I expect everything to disconnect, not only my icecast connection. So I'll monitor my USRobotics logs today and tomorrow so see if there is something strange. Regards, On Wed, Jun 11, 2008 at

Hi, Are you running behind an ADSL line? If so, what type of ADSL connection (PPPoA, RFC1483 bridged), what type of router, etc. Also the line quality (noise margin, line speed, rx/tx attenuation) may be an important issue. If the line is indeed gone for 15-20 seconds, this indicates a retrain/relogin of your connection. Maybe the logs from your modem can tell you more about these outages. I

Well, if it is the only option to overcome the problems I will certainly do it, On Tue, Jun 10, 2008 at 4:23 PM, Sascha Bieler <sascha.bieler at radiogong.de> wrote: > Ups? > > Is it possible to place a second (backup) streamer in another network and > you define a fallback mount? > > > > *From:* Taner Sener [mailto:tanersener at gmail.com] > *Sent:* Tuesday,

Hi Taner I doubt that the change of routes does not affect your connection, because this is normal practise with carriers (BGP or least cost routing) and usually it has no impact on the enduser, as it happens in milliseconds. My personal thinking is, that your ADSL Provider disconnects you once or twice a day to unload the DSLAM port and sometimes, if you do not have a fixed IP address, you

All, I am trying to configure hdlc support on T100P Digium card - everything seems ok... but it just does not work at all. I was able to compile all drivers, the light on the card becomes green when I plug T1 link.... but I even can't ping default router IP... there is no data coming back to me, so I am confused completely now. Also I tried both protocols - raw hdlc and cisco hdlc. The

Oi, quando abri a minha caixa adsl e vi o famoso Octal, assustei-me logo, no entanto, depois de ler o teu artigo, fiquei descansado, mas os problemas vieram a seguir... segui o howto por completo, instalei tudo, mas quando vou compilar o amedyn é reportado o seguinte erro : [root@portatil paulo]# cd amedyn [root@portatil amedyn]# make cd init && make clean make[1]: Entering directory

Hello I have serious problem with zhone z-plex 10 the device sometimes get red alarm on some channel and then the device suddenly shutdown. I try to unplugged the power chord and plug again, but the device still didn't up. I have to wait for long time to get this device up again. How can i fix this problem, so i can get this device immediately? Eris Riswanto

When I use the next code to print all the opcode name in a file xx.o whose source file contains statements "if (diff != 0) klee_assume(diff>0)", then an opcode name 'and' was printed. Where is the 'and' instruction from? I checked the file xx.ll of xx.o and I didn't find a 'and' instruction of these two statements. Besides, when I commented out statement

Based on simulations, I've come up with a simple function to compute the confidence interval for the variance of the binomial variance, where the true variance is v = rho*(1-rho)/n where rho = true probability of success and n = # of trials. For x = # successes observed in n trials, p = x / n as usual. For p < 0.25 or p > 0.75, I use the proportion-based transformed confidence

I have a recently installed Mellanox VPI interface in my server. This is an InfiniBand interface, which, through the use of adapters, can also do 10GbE over fiber. I have one of the adapter's two ports configured for 10GbE in this way, with a point to point link to a Mac workstation with a Myricom 10GbE card. I've configured this interface on the Linux box (eth2) using