similar to: R1000 Driver for RTL8110SC NIC on Biostar I945G-M7

I'd like to add a page for the Realtek r1000 NIC driver for the RTL8110SC (and others) chipset. This driver is not included in the kernel. I've previously posted to the general mail list: http://lists.centos.org/pipermail/centos/2007-February/075383.html I'm guessing this would go in the HardwareList section. Otherwise a page titled 'Realtek r1000 Driver' would work. my

Hello: I'm having issues with my CentOS 5.1/Xen installation. If I run the xen-bridge, I seem to get flaky ethernet. By flaky I mean everything seems fine from the host machine, but if I attempt to contact the host machine from another remote machine (eg. my laptop which is on the same subnet as the xen machine, separated by 10 ft of cable and a router) I either get extremely high ping

Hello: I'm having issues with my CentOS 5.1/Xen installation. If I run the xen-bridge, I seem to get flaky ethernet. By flaky I mean everything seems fine from the host machine, but if I attempt to contact the host machine from another remote machine (eg. my laptop which is on the same subnet as the xen machine, separated by 10 ft of cable and a router) I either get extremely high ping

Could I get write access to http://wiki.centos.org/HardwareList/CentOS5/RealTek/r1000? There's a couple of things I'd like to copy over from my CentOS4 R1000 page. Wiki Name: kirkbocek Thanks, Kirk Bocek

Bill, your CentOS 5 RTL8110 page should probably be updated. I've confirmed that there's a newer r8169 driver in the kernel that works with the RTL8110. RealTek's web site now carries the new r8169 instead of the r1000. The newer driver fixed a problem I was having on one host so we should probably recommend it over the older r1000. I've updated my CentOS 4 page. Kirk Bocek

What is the difference between these two fragments (taken from two different tblgen record dumps)? dag OutOperandList = (outs GPR:$rd); dag OutOperandList = (outs R2); The first is from the RISCV backend record dump. There will be a substitution at some point for $rd. In the second, I'm specifying R2, no substitution necessary. If I specify GPR64:R2 or i64:R2 in my Instruction def,

Hi - I have a machine which was originally built with Centos 5.0 including xen. It has all the current updates and here are some questions: The current problem is: 1) If I boot the non-xen kernel - it runs fine. If I boot the xen kernel - it boots - but has no network connectivity - and I get the following errors continuously in the messages log: Time/date: C5 Kernel: vif0.0: received packet

Hi, I would like to do a network install using PIXES boot, however the ethernet device was not supported by centos installation (RTL8110SC). How do i add this module into the initrd? I know i can use: mkinitrd --with=r8169 `uname -r`, but i did not know what is the standard modules included in the installation initrd of Centos. Thanks! --beast

Hi, our client wants us to use Biostar NF4 X4-A7 (nForce4-4X) based computer. I do not have access to nForce4-4X based computer to try. Anyone successful with C4.4 installation? Thanks, David Hrb??

I am booting 5.3 on an a770 biostar motherboard THe machine boots, I get the prompt from the DVD I hit return and the screen says kernel alive but it never gets past that. I tried booting again with noprobe on the command line same thing. I tried booting again with noprobe and noapic nolapic and same thing. Any thoughts on how to get past the halting?? Thanks, Jerry

(a) Mark (mhr) suggested I buy a bare bones box, when I reported the problem with the mainboard in this Dell Dimension 2400 box. Possibly I can have the mainboard repaired (and the PSU, if it is also having problems), and if so, I will give this one to my Stepson and go the bare bones box route and have a more powerful box for myself. I looked at two (2) very low end Desktop mainboards in the

Hello I've just been hit by one of the chipsets described at http://wiki.centos.org/HardwareList/RealTekRTL8111b. Because a) it does not work with the stock driver included in Centos 5.1 and b) I am very lazy and I do not like manually compiling modules each time a new kernel is installed (not to mention that I never forget anything, except for the important things which always go

Howdy, It appears that CentOS 5.2's support for the RTL8111B/C chip is incomplete. The wiki has some blanket statements regarding this support: http://wiki.centos.org/AdditionalResources/HardwareList/CentOS5/RealTek/r1000 http://wiki.centos.org/AdditionalResources/HardwareList/RealTekRTL8111b I could dive in an make the changes *I* think need to happen but I'd like to talk to people

On Tue, 2007-09-04 at 23:32 +0100, Karanbir Singh wrote: > Hi, > > Phil Schaffner wrote: > > Karanbir provided driver disk images and indicated that kmod drivers > > would be in CentOS-5 Extras, but apparently these never materialized. > > The only src.rpm I could turn up was the last link above, and I did get > > CentOS-5 x86_64 kmod-style drivers to build from

Remote box SNV93 (xVM kernel) 192.168.1.54 (NIC RTL8169) Attempts of ssh connection from CentOS 5.1 DomU 192.168.1.37 at SNV93 Dom0 (NIC RTL8110SC) # ssh user1@192.168.1.54 hangs .. TCPDUMP running on remote box (192.168.1.54) # tcdump -s 1600 -vv One entry generates for each ssh connection attempt. First:- 17:12:43.058821 IP (tos 0x0, ttl 64, id 19771, offset 0, flags [DF], proto TCP (6),

Hello, I am building a DRBD cluster with CentOS 4.4. Both nodes have RTL8169S-32 cards, Pheenet branded. I'm getting no more than 185 Mbps with the driver selected at installation (r8169). Downloading Realtek's r1000 climbs to some amazing 200Mbps. I am measuring performance with iperf, host to host, with a cat5e direct cable some 2.5ft long. Maybe disk I/O will be the bottleneck in my use

I'd like to add a page for the Realtek RTL8111b NIC. I'm not sure how you'd like to organize it since the page really could be relevant to both CentOS 4 and CentOS 5. I think a single page like: http://wiki.centos.org/HardwareList/RealTekRTL8111b Would work with links to both CentOS 4 *and* CentOS 5? However, if the wiki admins want two pages, that'll be fine too. Can you also

Hi, I'm planning to use Opus codec on a ARM cortex M7 device running at 400MHz. Con you please suggest the best configuration directives that I have to set in the config.h file in order to obtain the best perfromances on the cortex M7 architecture? Actually I have compiled libopus 1.2.1 with the following cnfiguration parameters: #define VAR_ARRAYS  1 #define FIXED_POINT  1 #define

Hi Just upgraded smoothly to long overdue Aptana M7 Beta which was released on 25/9/2007. FYI, the best way to upgrade from July''s M5 (M6 was skipped) is as follows :- 1) Click Help/Software Upgrades/Finad and Install 2) Manually adding the following update site to the update manager: http://update.aptana.com/update/rails/beta/3.2/site.xml

Is there anyway to force an autopickup on a cisco 7940 / 60 from the dialplan ? My problem is that I am originating a call from the AMI, with the internal user being called first, and then connecting to external user. However, sometimes the internal user doesn't pick up the phone, so the call is never placed. I need to know the results of the call so I need to be able to either a) get