similar to: broadcom 802.3ad

Hi all I'm trying to setup second ethernet on Dell 2950 server but there isn't any eth1 device (in the bios are ON) # dmesg |grep eth eth0: Broadcom NetXtreme II BCM5708 1000Base-T (B2) PCI-X 64-bit 133MHz found at mem f8000000, IRQ 169, node addr 001c23d878bb eth1: Broadcom NetXtreme II BCM5708 1000Base-T (B2) PCI-X 64-bit 133MHz found at mem f4000000, IRQ 169, node addr 001c23d878bd

Hi, I''ve run into the same issue as: http://lists.xensource.com/archives/html/xen-users/2006-07/msg00599.html In that, running the network bridge script kills networking completely, trying to ping the gateway gives me destination host unreachable. The card is: 09:00.0 Ethernet controller: Broadcom Corporation NetXtreme II BCM5708 Gigabit Ethernet (rev 11) Using the bnx2 module:

I am having the same problem. But, I cannot access to the following link for solution http://wiki.ncsa.uiuc.edu/wiki/Dell_PE1950_NIC_Firmware_Workaround Can someone send me the content of this link? Thanks. Pete, This may be relevant: http://wiki.ncsa.uiuc.edu/wiki/Dell_PE1950_NIC_Firmware_Workaround - Mike At 8/18/2006 09:40 AM Friday, Peter McEvoy wrote: Hi, I''ve run

Hi, I have a Dell PowerEdge 1950 with two NICs Broadcom NetXtreme II BCM5708 1000Base-T. I installed CentOS 5.1 and Xen 3.0.3 (RPM). One of my virtual machines has Windows 2003 Server. In this virtual machine my NICs appears like "Realtek RTL8139 Family PCI Fast Ethernet NIC". The problem is that when I ping to other machines sometimes the reply time value is very high: C:>

Hi, I hope someone can help me, I cannot seem to get a system's ethernet interface to correctly work in promiscuous mode... I have a Centos 6.4 system with 2 bnx2 interfaces on it. I have set up eth1 in promiscuous mode and am sending traffic to it using the port mirroring configuration on a Nortel 3510-24T switch. The switch reports that it is sending a fair amount of traffic to the

I am posting the message below again because it did not go through last night. Help! Steve Timm -- ------------------------------------------------------------------ Steven C. Timm, Ph.D (630) 840-8525 timm@fnal.gov http://home.fnal.gov/~timm/ Fermilab Computing Division, Scientific Computing Facilities, Grid Facilities Department, FermiGrid Services Group, Assistant Group Leader.

Hi all, I have a problem when from domU I need to configure a network interface. My system configuration is the next: dom0: xen 3.4.3 with 2.6.18-238.9.1.el5xen kernel, making pci back from a network card. All ok. This is the result from "lspci -v -s 09:00.0" 09:00.0 Ethernet controller: Broadcom Corporation NetXtreme II BCM5708 Gigabit Ethernet (rev 12) Subsystem: Broadcom

(first post) Dear all, I have been wrestling with this issue for the past few days ; googling around doesn't seem to yield anything useful, hence this cry for help. Setup : - I am running several RHEL5.4 KVM virtio guest instances on a Dell PE R805 RHEL5.4 host. Host and guests are fully updated ; I am using iperf to test available bandwidth from 3 different locations (clients) in the

Hello list, I have two differents installation Xen Hypervisor on two identical physical server, on the same switch : The problem is on my new server (Xen 4.0.1 with pvops kernel 2.6.32.24), I have bad performance on bandwidth I have test with a files copy and "iperf". Result iperf average: Transfert Bandwidth XEN-A -> Windows

I have a new x3655 IBM and whenever the /etc/xen/scripts/network-bridge script starts, the ethernet would no longer work. This post isn''t about the cause, but the fix. I did a lot of tcpdumps and Googling, but I''ll spare you that. All they do is prove that yes, there is an issue. :) I tried Debian 4.0 i386/amd64 and Ubuntu 7.04 Server i386/amd64 and they all exhibit the

Hello All, I have one CentOS 6 KVM virtualization server that I built around a year ago (best I can tell it was in October 2012) at which time I would have been installing 6.3 [0]. That particular install used the Consistent Network Device Naming [1] conventions (PCIe NICs are p1p1, p1p2). I started to build out a new KVM virt server (kickstarting a 6.4 install now as compared to 6.3 back then)

Hi, I have been playing this weekend with bonding on PCI netcards and found that all of netcards I have, but old 3com, do not support MII. So bonding is not going to happen with them. Do you have some pci netcards supporting MII successfully running on bonging? Thanks, David Hrb??

Hi, After changing cables,switches,ports, I came to the conclusion that bce is reporting input errors that are not there, or creating them. I checked this with 3 different boxes, all Dell-2950/Broadcom NetXtreme II BCM5708 1000Base-T (B2), and one of them, while running Solaris, reported 0 errors after a week, and freebsd after a few minutes its count was > 100. The errors appear under

Hello, I''ve this strange problem. When Xen kernel start and it try to start eth devices, network doesn''t work. It seems to be a problem with NICs firmware. Anyone had this problem? Do you know where I can download firmware upgrade? (on DELL''s site I''ve just searched...) Thanks, Carlo No virus found in this outgoing message. Checked by AVG Free Edition.

I installed 64-bit xen 3.1.0 (from xensource.com tarballs) on three new machines today, using a configuration setup that I''ve used successfully many times before. However, I encountered a new problem. These are Dell Poweredge 1950 servers, by the way. >From lspci 04:00.0 Ethernet controller: Broadcom Corporation NetXtreme II BCM5708 Gigabit Ethernet (rev 12) 08:00.0 Ethernet

I make some networking performance tests for Linux 3.10.13 #1 SMP is that normal Linux (pktget) ----> Linux (router) ----> Linux (Sink) eth0: 0.00 P/s 652024.78 P/s 652024.78 P/s eth1: 652175.58 P/s 2.98 P/s 652178.55 P/s with echo 0 >/proc/sys/net/bridge/bridge-nf-call-iptables CPU is about 2% with echo 1

host and guest both centos 5.5 network is 192.168.62.40 host is setup as follows [root at cloud2 ~]# ifconfig br0 Link encap:Ethernet HWaddr 00:1A:64:12:10:D9 inet addr:192.168.62.199 Bcast:192.168.63.255 Mask:255.255.254.0 inet6 addr: fe80::21a:64ff:fe12:10d9/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:1705488

Hi, tuning my network fixing nic's speed and duplex (both on server and switch) i got this error with bce driver: # ifconfig bce0 bce0: flags=8843<UP,BROADCAST,RUNNING,SIMPLEX,MULTICAST> metric 0 mtu 1500 options=1bb<RXCSUM,TXCSUM,VLAN_MTU,VLAN_HWTAGGING,JUMBO_MTU,VLAN_HWCSUM,TSO4> ether 00:15:c5:fe:11:01 inet 192.168.1.13 netmask 0xffffff00 broadcast

Hello all. We recently purchased HP Proliant DL380 G7 server and also a HP Lefthand P4500 G2 24TB iSCSI box. The server itself has Quad Ethernet based on the BCM5709 Chipset from Broadcom (NetXtreme II). My main question is about iSCSI offload mechanism, as iSCSI itself is pretty new to me but I have gotten a good hold on it tho. I have managed to setup and configured our Lefthand box into

I totally agree with Luc Boudreau about this problem. On modern branded server they ALL use Broadcom chipset... I must admit that: a) lot of people are experiencing the problem but can tolerate it or b) someone already experienced this problem and solved it Lets'' approach the problem pragmatically... just start with a survey on the list. ... hope we solve this issue soon. Ivan