similar to: shorewall shutting down eth0

Hello, Which port Smb4K uses? I am not able to use Smb4K on my server for the local network. Thanks Varun

Hello, My server is on Mandrake 10.1 off. eth0 is WAN with static IP connected 512 DSL eth1 is LAN. I have NAT working on 192.168.0.0. I want to feed a second subnet 192.168.21.0. What is the best way to implement it ? Thanks Varun

Hello, I want to block a particular IP on the local network. Howto do that ? Thanks Varun

Hi There, Due to shortage computer, I need to install Apache to my Shorewall box (192.168.1.1) But the real web server is on another box (192.168.1.2) I tried to put rule: DNAT net loc:192.168.168.1 tcp 80 But everytime www connection coming in, it will hit my shorewall Any solution? Cheer Access Yahoo!7 Mail on your mobile. Anytime. Anywhere. Show me how:

http://shorewall.net/pub/shorewall/Snapshots ftp://shorewall.net/pub/shorewall/Snapshots Problems Corrected since version 1.4.6: 1) Corrected problem in 1.4.6 where the MANGLE_ENABLED variable was being tested before it was set. 2) Corrected handling of MAC addresses in the SOURCE column of the tcrules file. Previously, these addresses resulted in an invalid iptables command.

I am trying shorewall as my previous post With alisias on eth1 loc and 4 pptp client vpns. The odd thing is when I enter one of the vpns in interfaces such as vpn1 it works. But if I enter the vpn in the hosts file shorewall blocks the vpns. shorewall/hosts #ZONE HOST(S) OPTIONS loc eth1:192.168.25.0/24 loctw eth1:192.168.50.0/24 locsa eth1:192.168.75.0/24 vpntw

This is a minor release of Shorewall. WARNING: This release introduces incompatibilities with prior releases. See http://www.shorewall.net/upgrade_issues.htm. Changes are: a) There is now a new NONE policy specifiable in /etc/shorewall/policy. This policy will cause Shorewall to assume that there will never be any traffic between the source and destination zones. b) Shorewall no longer

Hello, > My server is on Mandrake 10.1 off. > eth0 is WAN with static IP connected 512 DSL > eth1 is LAN. I am little confused about NAT. I have a static IP from ISP I want to do a NAT on eth0. What should I use in shorewall masquerading or static nat ? Thanks Varun

Hello , The folllowing is the error problem: Validating interfaces file... ERROR: The ''norfc1918'' option may not be specified on an interface with an RFC 1918 address. Interface:eth2 The shorewall interface file: net eth2 detect tcpflags,routefilter,norfc1918,nosmurfs,logmartians P.S. I tried to remove norfc1918 from interface

Hello, Since FC3 has been a very recent release I was just wondering if there are issues related to asterisk installation on FC3. Thanks Varun

Hi, I have a Linux firewall based on shorewall with 2 NIC and ADSL (ppp0). My ppp0 ip is fixed. The internal NIC, eth1, is bridged with tap0, tap1 and tap2 to form br0. br0 subnet is 192.168.2.0/24. The firewall is configured to masq internal traffic and block whatever needs to be blocked. It is also configured to tunnel openvpn v1.6. I have a roaming laptop running XP. I can create a tunnel

Hello, I am not able to use ftp and ssh on the lan. Both the port are open. I have the lines on the rules file : # Accept SSH connections from the local network for administration # ACCEPT loc fw tcp 22 # # Accept ftp connections from the local network for administration # ACCEPT loc fw tcp 21 Thanks in advance Varun

Hi there, Let me just start by saying that I am a bit of a Linux newbie, but that Shorewall seems an excellant product. The issue I''m reporting wont stop me from using it, it still does 99% of what I need. Anyway, I have a resonably simple two interface system. My server (HatMannz, P3-900MHz with a RAID-1 array of 80GB IDE drives running Red Hat 9.0) connects to a cable modem via eth1

Hello, My server is on Mandrake 10.1 off. eth0 is WAN with static IP connected 512 DSL eth1 is LAN. I have enabled shorewall and it has blocked access to the net on my server. My default shorewall settings are : Source zone Destination zone Policy Syslog level Traffic limit loc net ACCEPT None None net Any

Hello, > My server is on Mandrake 10.1 off. > eth0 is WAN with static IP connected 512 DSL > eth1 is LAN. I need a little clarification on static nat settings in shorewall. external address - static IP internal address - ? for the internal address should I put my eth1 IP or the general subnet range. For example 192.168.0.0. I am also not sure about : Active for firewall system? yes

Hello all, I had setup shorewall before succesfully with a normal LAN to internet connection. Now I''m connected to the internet via VPN and I got problems with configuring Shorewall. Any help is appreciated. This is my setup: - Gentoo Linux laptop (kernel gentoo-dev-sources-2.6.8.1) with Shorewall 2.0.4 (setup for Standalone one interface) and iptables 1.2.11 - VPN client is

Hello, I am not able to open the webmin web interface on my server. Shorewall is blocking it. How to allow it on the server. Thanks Varun

Hi people, I am running the latest version of Debian ''Sarge''. I have installed hopefully the latest version of shorewall, as followed by the website. The firewall has been installed with no problems, runs ok, but I have found a strange problem, maybe it me *shrug* My setup: Internet<-->cablemodem<-->Debainfirewall<-->hub<-->windowspc I am cable, and

Hello, My server is Mandrake 10.1 eth0 is WAN with static IP connected to 512k DSL eth1 is LAN. I am using squid proxy for internet with NSCA auth. I am able to send and recieve mails. One of the client system wants to be able to make net2phone calls. As of now he is not able to. Howto allow net2phone calls ? Thanks Varun

We switched over from a bordermanager firewall to a shorewall firewall. Some stuff is not working now. I realized that I had not created the route for the network that is not working however once I created it, it still didn''t work. Most of our network is fine however some pieces are not working. [Net] - [Shorewall] - [LAN] - [Cisco] - [Clients and servers not working] The firewall