similar to: static nat address

Hello, > My server is on Mandrake 10.1 off. > eth0 is WAN with static IP connected 512 DSL > eth1 is LAN. I am little confused about NAT. I have a static IP from ISP I want to do a NAT on eth0. What should I use in shorewall masquerading or static nat ? Thanks Varun

Hello, My server is Mandrake10.1 eth0 is WAN with static IP eth1 is LAN I would like all traffic from 2 client - 192.168.0.253 and 192.168.0.248 on the lan to go straight to outgoing interface. I am not sure whether to use DNAT or ACCEPT. Can anybody clarify ? Thanks Varun

Hello, Which port Smb4K uses? I am not able to use Smb4K on my server for the local network. Thanks Varun

Hello, My server is on Mandrake 10.1 off. eth0 is WAN with static IP connected 512 DSL eth1 is LAN. My default shorewall settings are : Source zone Destination zone Policy Syslog level Traffic limit loc net ACCEPT None None fw net ACCEPT None None net Any

Hello, Since FC3 has been a very recent release I was just wondering if there are issues related to asterisk installation on FC3. Thanks Varun

Hello, I want to block a particular IP on the local network. Howto do that ? Thanks Varun

Hello, My server is on Mandrake 10.1 off. eth0 is WAN with static IP connected 512 DSL eth1 is LAN. I have NAT working on 192.168.0.0. I want to feed a second subnet 192.168.21.0. What is the best way to implement it ? Thanks Varun

Hello, My server is on Mandrake 10.1 off. eth0 is WAN with static IP connected 512 DSL eth1 is LAN. I have enabled shorewall and it has blocked access to the net on my server. My default shorewall settings are : Source zone Destination zone Policy Syslog level Traffic limit loc net ACCEPT None None net Any

Hello, I have an onboard sound AC97. Howto to find if my sound is full duplex ? And if my sound is not full duplex then please recommned me a good full duplex sound card that is supported on linux. Thanks varun

Hello, Is it possible to use v92 ( a few chipsets version ) modem as FXO PCI modules ? While googling I found some postings on the subject. Thanks Varun

Hello, I am not able to use ftp and ssh on the lan. Both the port are open. I have the lines on the rules file : # Accept SSH connections from the local network for administration # ACCEPT loc fw tcp 22 # # Accept ftp connections from the local network for administration # ACCEPT loc fw tcp 21 Thanks in advance Varun

Hi ! I have setup a complete shorewall now with DMZ, and Private zones and masq, rules, port-forwarding etc. worx like expected. BUT I have a wish to use a couple of more public IP''s and relate those to inernal servers on the DMZ zone and i am now so confused about it. I have searched this archive for SNAT port allow Setup: 3 public adresses on the WAN nic. lets call them 80.80.80.80 -

Hello, I am not able to open the webmin web interface on my server. Shorewall is blocking it. How to allow it on the server. Thanks Varun

Hello, I want to build a PBX with the following specs : 1. we have two trunk lines 2. we need upto 8 extensions - all analog phones maybe one voip phone What is hardware that I need and where to find it ? Thanks Varun

Hello everyone, really not sure if this is a LARTC question or not, but I have several hundred users all MASQ''d behind a single static IP. Users are reporting that certain websites are blacklisting that single static external IP for various reasons. What I would like to do is use several external IP''s and have a MASQ''d user getting a random one each time. Here is

Hello, I am not able to open the web interface for the wrt54g router on the lan. Which port does it use ? Thanks Varun

Hello, Can the wildcard x100P be bought of the shelf in stores - say in Singapore. Thanks Varun

Hello, My server is Mandrake 10.1 eth0 is WAN with static IP connected to 512k DSL eth1 is LAN. I am using squid proxy for internet with NSCA auth. I am able to send and recieve mails. All that is working fine. Is it possible to do a NAT to one PC ( particular IP) in the same subnet ? If yes how ? Thanks Varun

Hello, My server is Mandrake 10.1 eth0 is WAN with static IP connected to 512k DSL eth1 is LAN. I am using squid proxy for internet with NSCA auth. I am able to send and recieve mails. One of the client system wants to be able to make net2phone calls. As of now he is not able to. Howto allow net2phone calls ? Thanks Varun

Hello, How good is :SPA 841 form SIPURA. Thanks Varun