similar to: net2phone calls

Hi, I?m looking for settings to configure net2phone carrier in my asterisk. I found this configurations, but it?s not work. I don?t known if this configuration is for voice line or voice access account. Anybody can help me, with other configuration? Thanks. ---- *sip.conf* [general] useragent = X-Lite release 1103m register => PHONENUMBER:PASSWORD@sip.net2phone.com [net2phone] type = peer

I've been trying to use net2phone's sip service at sip.net2phone.com with * but keep getting SIP/2.0 401 Unauthorized. Do you know if this should be possible? So far: I can use an ata186 to connected directly to n2p through sip.net2phone.com without any special settings. I can connect from * to iconnecthere, but, whatever I try from * to n2p produces "SIP/2.0 401 Unauthorized"

Hi All, As Net2Phone don't permit more than one session per account, I configured about 10 sip trunks and configure multiple trunk routing but once the first trunk is used I cannot make additional calls, I also cofigure my dial plan in other way using the chanisavail command but still not working. The chanisavail command configuration is correct as I can make calls using other trunk than

Hi! Net2Phone is getting a common SIP status code, "404 Not Found," when trying to place a call to our Asterisk server. We're hoping someone on the list can shed some light on why this is happening. We can process a call from Asterisk to Net2Phone without any problems. Net2Phone sends the INVITE but immediately gets the "404 Not Found." The "To:" field

I can cut and paste the log file from a reload right now, and provide you with the other information when I get home after work: tmp*CLI> sip debug SIP Debugging Enabled tmp*CLI> reload Mar 21 14:52:42 NOTICE[23231]: indications.c:397 ast_unregister_indication_country: Removed default indication country 'us' 11 headers, 0 lines Reliably Transmitting: REGISTER

When I try call to net2pohe sip service in my debug I look next: ---------------------------------------------------- We're at 192.0.0.0 port 27916 Answering with preferred capability 1 Answering with preferred capability 2 Answering with preferred capability 256 Answering with capability 4 Answering with capability 8 Answering with capability 16 Answering with capability 32 Answering with

Dear, I have this scenario: - PBX Asterisk 1.6.2.10 with private IP 192.168.0.10 - Behind a Cisco ASA firewall that connects to Internet - SIP trunk to Net2Phone with these parameters (nat=no): host=200.58.113.60 username=DOLLY secret=123456 port=5060 type=peer dtmfmode=rfc2833 disallow=all allow=alaw&ulaw nat=no canreinvite=no qualify=yes -Softphones Xlite The PBX can't register to

As a newbie, can anyone advise me if Asterisk can route international calls to a US based service such as Net2Phone so we can take advantage of the internet and save on calls? That would be my main reason for an Asterisk based PBX. Chris Mason masonc@masonc.com Box 340, The Valley, Anguilla, British West Indies Tel: 264 497 5670 Fax: 264 497 8463 Cell: 264 235 5670

Hello we are a small call center with only 8 lines we use max4 and the 2-2 port gateways from net2phone . There equipment is good but we are getting hit by lower cost competition. We need to be able to compete. We have a couple of providers who are 50% less in some cases even more. So it makes sense that we would like to be able to compete . Since we have spent quite a bit of money on existing

Hello, My server is Mandrake 10.1 eth0 is WAN with static IP connected to 512k DSL eth1 is LAN. I am using squid proxy for internet with NSCA auth. I am able to send and recieve mails. All that is working fine. Is it possible to do a NAT to one PC ( particular IP) in the same subnet ? If yes how ? Thanks Varun

Hello, My server is Mandrake 10.1 eth0 is WAN with static IP connected to 512k DSL eth1 is LAN. I am using squid proxy for internet with NSCA auth. I am able to send and recieve mails. All that is working fine. My masq file is as follows: eth0 192.168.0.0/24 61.247.253.22 eth0 192.168.21.0/24 61.247.253.22 I want do a NAT to a particular system. The objective being to avoid going through

Hi all, i need configure module nsca on puppet. I want ensure stopped the service, but puppet detect wrong the process. For example: in this sistuation: hululi ~ # ps aux | grep nsca nagios 12730 0.0 0.0 16708 752 ? Ss 07:47 0:00 nsca - c /etc/nagios/nsca.cfg --daemon root 12778 0.0 0.0 8308 792 pts/8 S+ 07:47 0:00 grep --colour=auto nsca Puppet works

Has anyone had any success running net2phone on wine. I tried it but I recieved an error message: ]$ wine net2phone.exe Invoking /opt/wine/bin/wine.bin net2phone.exe ... /usr/bin/wine: line 380: 6945 Terminated tail -f $log_name Wine failed with return code 2 Even if I can't make it work I'm really interested to understand what's happening. (though net2phone is basically the

I'm trying to register with net2phone. I've already changed chan_sip.c, User-Agent: string to say "User-Agent: Cisco ATA 186 v2.16 ata18x (030401a)". But still I'm getting the error msg. Here is the debug msg: IP Address is xxx.xxx.xxx.xxx 11 headers, 0 lines Reliably Transmitting: REGISTER sip:66.33.146.12 SIP/2.0 Via: SIP/2.0/UDP

Hello, Which port Smb4K uses? I am not able to use Smb4K on my server for the local network. Thanks Varun

Hello, My server is on Mandrake 10.1 off. eth0 is WAN with static IP connected 512 DSL eth1 is LAN. My default shorewall settings are : Source zone Destination zone Policy Syslog level Traffic limit loc net ACCEPT None None fw net ACCEPT None None net Any

Hello, Since FC3 has been a very recent release I was just wondering if there are issues related to asterisk installation on FC3. Thanks Varun

Hello, I want to block a particular IP on the local network. Howto do that ? Thanks Varun

Hello, My server is on Mandrake 10.1 off. eth0 is WAN with static IP connected 512 DSL eth1 is LAN. I have NAT working on 192.168.0.0. I want to feed a second subnet 192.168.21.0. What is the best way to implement it ? Thanks Varun

Hello, > My server is on Mandrake 10.1 off. > eth0 is WAN with static IP connected 512 DSL > eth1 is LAN. I am little confused about NAT. I have a static IP from ISP I want to do a NAT on eth0. What should I use in shorewall masquerading or static nat ? Thanks Varun