similar to: wrt54g web interface

Hello, Which port Smb4K uses? I am not able to use Smb4K on my server for the local network. Thanks Varun

Hello, My server is on Mandrake 10.1 off. eth0 is WAN with static IP connected 512 DSL eth1 is LAN. My default shorewall settings are : Source zone Destination zone Policy Syslog level Traffic limit loc net ACCEPT None None fw net ACCEPT None None net Any

Hello, Since FC3 has been a very recent release I was just wondering if there are issues related to asterisk installation on FC3. Thanks Varun

Hello, I want to block a particular IP on the local network. Howto do that ? Thanks Varun

Hello, > My server is on Mandrake 10.1 off. > eth0 is WAN with static IP connected 512 DSL > eth1 is LAN. I am little confused about NAT. I have a static IP from ISP I want to do a NAT on eth0. What should I use in shorewall masquerading or static nat ? Thanks Varun

Hello, > My server is on Mandrake 10.1 off. > eth0 is WAN with static IP connected 512 DSL > eth1 is LAN. I need a little clarification on static nat settings in shorewall. external address - static IP internal address - ? for the internal address should I put my eth1 IP or the general subnet range. For example 192.168.0.0. I am also not sure about : Active for firewall system? yes

Hello, My server is on Mandrake 10.1 off. eth0 is WAN with static IP connected 512 DSL eth1 is LAN. I have enabled shorewall and it has blocked access to the net on my server. My default shorewall settings are : Source zone Destination zone Policy Syslog level Traffic limit loc net ACCEPT None None net Any

Hello, I have an onboard sound AC97. Howto to find if my sound is full duplex ? And if my sound is not full duplex then please recommned me a good full duplex sound card that is supported on linux. Thanks varun

Hello, Is it possible to use v92 ( a few chipsets version ) modem as FXO PCI modules ? While googling I found some postings on the subject. Thanks Varun

Hello, I am not able to use ftp and ssh on the lan. Both the port are open. I have the lines on the rules file : # Accept SSH connections from the local network for administration # ACCEPT loc fw tcp 22 # # Accept ftp connections from the local network for administration # ACCEPT loc fw tcp 21 Thanks in advance Varun

I''ve set up shorewall with the two-interface mode. pc #1 eth1 ---> ppp0 ---> Internet eth1: 10.10.10.254 eth0: 10.10.10.1 > via a crossover cable pc #2 eth0: 10.10.10.2 (gateway=10.10.10.254) I am able to surf the net with pc #1, but pc #2 is completely cut off from pc #1 and the net. I am also unable to ping from and to pc #2.

I''m not subscribed to the users list but I''ve been reading the archives. The OP should NOT try using bridging with either FC 3 or FC 4 at this time because the combination of Netfilter and bridging is currently broken in the kernel''s included with those distros (as reported in another thread on the list). -Tom -- Tom Eastep \ Nothing is foolproof to a sufficiently

Hello, I am not able to open the webmin web interface on my server. Shorewall is blocking it. How to allow it on the server. Thanks Varun

Hello, I''m a very happy user of shorewall but I have found a problem or maybe a misconfiguration I made which I can not resolve. I use a fairly large blacklist based on probes, nimda & codered attacks, proxy & relay probes etc. The only problem is that I want to block incoming trafic on all ports FROM a block but it does also block a httpd, ping etc TO a ip in a block what I do

Hello, My server is on Mandrake 10.1 off. eth0 is WAN with static IP connected 512 DSL eth1 is LAN. I have NAT working on 192.168.0.0. I want to feed a second subnet 192.168.21.0. What is the best way to implement it ? Thanks Varun

Hello, I want to build a PBX with the following specs : 1. we have two trunk lines 2. we need upto 8 extensions - all analog phones maybe one voip phone What is hardware that I need and where to find it ? Thanks Varun

How does one interpret the mac addresses in the log which seem to have 14 segments... Example, this appears in the log... 00:40:c7:2e:09:c0:00:01:64:4a:70:00:08:00 Yet I can''t find that in the arp table norcomix:~ # arp -an ? (192.168.2.148) at 00:10:4B:6A:AE:E7 [ether] on eth1 ? (192.168.2.149) at 00:D0:B7:1D:F2:F2 [ether] on eth1 ? (24.237.19.16) at 00:10:DC:67:BA:80 [ether] on eth0 ?

Since you''ve started signing your email, Tom, my machine can''t verify your sig. Where are you publishing your key? -- John Andersen - NORCOM http://www.norcomsoftware.com/

Hello, My server is Mandrake10.1 eth0 is WAN with static IP eth1 is LAN I would like all traffic from 2 client - 192.168.0.253 and 192.168.0.248 on the lan to go straight to outgoing interface. I am not sure whether to use DNAT or ACCEPT. Can anybody clarify ? Thanks Varun

Hello, Can the wildcard x100P be bought of the shelf in stores - say in Singapore. Thanks Varun