similar to: Interest in NTFS

Hello list, I had to boot a Dell Diagnostic Disk today, and tried doing this via memdisk - which was when I noticed memdisk isn't working for me at all, neither from pxelinux nor syslinux. After trying around with 'raw', 'bigraw' and the like I noticed it doesn't even do anything when just using: LABEL diag KERNEL memdisk .. when I try that: boot: diag nothing

Hello all, I understand that during PXE boot, it goes into the pxelinux.cfg and it states: 1. "it will search for the config file using its own IP address in upper case hexadecimal, e.g. 192.0.2.91 -> C000025B (you can use the included progam "gethostip" to compute the hexadecimal IP address for any host.) If that file is not found, it will remove one hex digit and try

Hello, I know this might be slightly off-topic, but I know at least hpa has an intimate knowledge of the linux boot process - and I would want to use it with syslinux/pxelinux, so I figure it might not hurt too much to ask: Is it possible to embedd the initrd with the linux kernel in a way similiar to how it works on some embedded systems? There, you provide an object file with the filesystem,

Is it possible to specify the root device in extlinux.conf by an ext2 label or uuid? How difficult is it to add this support if it is not there? I am in a situation where this is needed and my fstab is configured appropriately, but extlinux.conf still needs to be manually updated when the root drive changes to a different scsi device (due to the number of drives on the bus and the order of the

Hello, Has anyone thought about how one could use the "keeppxe" option with a vmlinuz/initrd? It would allow one to boot this combination, and if possible the linux kernel/initrd (assuming we have busybox in there) would not have to run udhcp and instead leverage what pxe stack information is loaded. The problem is I don't know of any PXE/UNDI linux utilities to look at the pxe

Hello, I was browsing the code for memdisk (I want to adjust it to my hardware) and noticed a couple of things that I am struggling to understand. I would appreciate if someone could clarify the following mysteries to me: 1) _binary_memdisk_bin_start[], _binary_memdisk_bin_end[] and _binary_memdisk_bin_size[]; These variables are declared (as extern const chat in 'setup.c')

Axel and everyone Your questions are valid. I had similar question when I bought these cards. These cards in particular have no rom chip on the pci card. If you plug these into a computer they do nothing until you load them with there firmware. When vt6410 are used on motherboards not as stand alone cards the bios has this firmware and loads it into the chip set on boot making them show up

Hi, I looked through the documentation and the mailing list archives but could not yet find out whether this could be made to work. The task I want to use that feature for is being able to collect firmware updates for servers and their components and boot those updates from a notebook with DHCP/TFTP-Server. That would greatly reduce setup time for new server installations. The problem is that

Hi all, I''m interested in starting a ruby/rails user group in Ireland and I''m trying to gauge the level of interest. So if you''re interested please get in touch (aidanf at gmail.com). I would also appreciate any suggestions/pointers about starting/organizing a user group. cheers, AF ------------------------------- http://www.aidanf.net

Folks, We are contemplating holding a Birds of a Feather session titled "Julia and LLVM: Implementing a fast dynamic language for technical computing" at the LLVM 2012 European Conference on April 12-13 in London. http://llvm.org/devmtg/2012-04-12/ Would this be of interest to the LLVM developer and user community? It would be great if you could drop me a line. It will help us gauge

I've been working on improving the startup performance of lldb, and ran into an issue with llvm::HashString. It works a character at a time, which creates a long dependency chain in the processor. On the other hand, the function is very short, which probably works well for short identifiers. I don't know how the mix of identifier length seen by lldb compares with that seen by

https://bugzilla.mindrot.org/show_bug.cgi?id=1213 Andreas Kotes <count-mindrot at flatline.de> changed: What |Removed |Added ---------------------------------------------------------------------------- CC| |count-mindrot at flatline.de Severity|normal |major --- Comment #6 from

Hi, Any advice/comments on the potential for hosting some personal Ruby applications from home? (i.e. for learning, sharing with friends etc) Would the basic concept be: * Need to buy a static IP address from you ISP * By a domain name and point it to the static IP address * Run Apache as the front end web server - Q: What basic lockdown/security steps should one take? * Perform a PORT

Hi group As promised some months ago, I'm letting you know that lockdown is now ready for testing. Please don't study the code to much, I know it is a mess and therefore a rewrite is on it's way. But feel free to take a look at the features offered, how you use them and the default settings. When lockdown is ready for production usage, I'll release version 1.0. I guess that will

Hello everybody, I'm a newbie in this list, so I don't know if it's the appropriate place for my question. Anyway, I'd be happy to find out the solution. Please, has anyone simple answer for: I'm looking for an exact list of files, which: 1. MUST have... 2. HAVE FROM BSD INSTALLATION... 3. DO NOT NEED... 4. NEVER MAY... ...the suid-bit set. Of course, it's no problem to

Hi, Does anybody has experience with high capacity PSTN voicemail and asterisk, running more then 5k mailboxes for PSTN users ? How many mailboxes can I serve with 4xE1 card if we assume that we have enough harddrive capacity. What would be server requirements. Would the CPU load be the same when storing voicemails in gsm format as compresing to gsm for ip calls ? Any hints would be greatly

Hello, I need to reconfigure Gnome in CentOS for avoiding that a normal user could lock screen using task bar option and/or "Super L" key (Windows Key + L). How could I configure Gnome? I need to do that in several computers, so I can't do "login" in X environment of each computer, but I need to reconfigure executing from command line (multiple SSH connections).

https://bugzilla.samba.org/show_bug.cgi?id=5459 Summary: Large amount of files makes checksum count negative Product: rsync Version: 3.0.2 Platform: x64 OS/Version: Linux Status: NEW Severity: major Priority: P3 Component: core AssignedTo: wayned@samba.org ReportedBy:

Hi all, I'm mounting a LTSP server whith CentOS 4.4. The default desktop will be Gnome. I'm looking for lockdown tool and I think Pessulus maybe a good option, but I don't found it with yum. ?Is Pessulus included in CentOS? ?Another lockdown tools as alternatives? Thanks in advance. -- Jordi Espasa Clofent PGP id 0xC5ABA76A #http://pgp.mit.edu/ FSF Associate Member id 4281

Hi I''ve just started using wxruby2-preview-0.0.36-i386-mswin32 outsourcing layout part to the external XRC file. Almost everything seems to be fine. Only that I can never retrieve Gauge objects in the main script. What I''ve been trying is something like this: class MainFrame < Wx::Frame include Wx def initialize(parent) super(nil,-1, "")