similar to: Sweex PP200 650VA UPS - Success report

On Sep 6, 2019, at 3:43 PM, Martyn Hill wrote: > > Just thought to share my findings getting a Sweex PP200 650VA UPS working with NUT (I didn't see this particular model listed on the HCL.) Thanks! One of the other Sweex models shows a few instant commands: https://networkupstools.org/ddl/Sweex/INTELLIGENT_UPS_1500VA_P220.html Is anything listed when you run `upscmd -l ups`?

Hello, have some of you tried sweex UPS 1500VA (http://www.sweex.com/en/assortiment/power-security/power-protection/PP220). It is not listed in hardware compatibility list. As I can see, sweex can be problematic with drivers, but it is not possible to change this UPS to other model now. It is connected by USB and lsusb says only: Bus 002 Device 004: ID 0665:5161 Cypress Semiconductor USB to

Hello folks, I have a question regarding a sweex product. Its bundled with UPSmart v 2.12. I installed nut accordingly to the user manual included in the software. A quick check of data/drivers.list revealed to me i should use the: "Sweex" "500/1000" "contact closure - shipped with UPSmart" "genericups upstype=7" driver this driver

Hi, I'm trying to get a sweex ups working with nut on debian sarge. This one: http://www.sweex.com/producten.php?lang=1&%20sectie=&item=59&artikel=95 It's shipped with UPSmart and according to the compatibility list it should work with the genericups upstype=7 driver. But it doesn't. I get: mybox:/etc/nut# /etc/init.d/nut start Starting Network UPS Tools: (upsdrvctl

Hi, FYI for all whom have the Sweex manageable UPS. I got my sweex manageable UPS500VA working with NetworkUPSTools using the ippon driver. Here is my the ups.conf file: [ups] driver = ippon port = /dev/cuad0 desc = "Server" Has anyone tried the ippon driver with Sweex 600VA, 700VA, and 800VA models? Regards, Jan

Hi, I am using a ALLNET 91500 UPS with blazer_usb driver /usr/lib/ups/driver/blazer_usb -a ups91500 -L Network UPS Tools - Megatec/Q1 protocol USB driver 0.10 (2.7.1) I have this settings: upsc ups91500 at localhost battery.charge: 100 battery.runtime: 12000 battery.voltage: 27.50 battery.voltage.high: 27.3 battery.voltage.low: 18.0 device.type: ups driver.flag.novendor: enabled driver.name:

Hello, I have a UPS branded as "Energit MXE II" that comes with the infamous Winpower software (as already discussed in this old thread <http://nut-upsdev.alioth.debian.narkive.com/m0FWk43o/blazer-usb-compatibility-with-ippon-backpro-upses-phoenix-power-co-ltd-usb-to-serial-controller>). This same UPS appears to be sold as "Centralion Titan Elite" and maybe other names

--- Arjen de Korte <nut+users at de-korte.org> wrote: > > > I also did: > > > > # ./megatec_usb -DDDDD -x vendor=06da -x mfr=OMRON > > /dev/usb/hiddev0 > > Please have a look at 'man 8 megatec_usb' again. > > You probably need to specify the '-x vendorid' and > '-x productid' options > and most likely, the

--- Arjen de Korte <nut+users at de-korte.org> wrote: > > > I also did: > > > > # ./megatec_usb -DDDDD -x vendor=06da -x mfr=OMRON > > /dev/usb/hiddev0 > > Please have a look at 'man 8 megatec_usb' again. > > You probably need to specify the '-x vendorid' and > '-x productid' options > and most likely, the

Arjan, I am forwarding your email to the nut-upsuser mailing list. I am not an expert on the Powermust driver; hopefully somebody on the mailing list will be able to help you! -- Peter Arjan DJ wrote: > > Dear Peter, > Some days ago I bought a Sweex UPS (500VA) and now I have set up NUT (using > the Powermust driver) and everything is working fine. Invoking upsmon -c fsd > gives

Hi, I'm trying to figure out why my Sweex CA000022 is not detected by wcfxo on my SuSE Pro 9.3 running on a VIA EPIA SP motherboard. The card should work as its an Intel 82537EP based card. When Booting the IRQ assignments for the board indicate: Bus Dev Func Vendor Dev Class 0 20 0 8086 1080 0703 lspci shows: 0000:00:14.0 Modem: Intel Corporation: Unknown device 1080

First off, my apologies for bringing back this thread from the dead (September 2005, http://lists.alioth.debian.org/pipermail/nut-upsdev/2005-September/000150.html), however my problem seems relevant enough that I wondered what happened to this thread as it seems to have died after the message I quote below. Despite the fact that I am having trouble getting my Sweex 1000VA UPS (USB) to work, and

First off, my apologies for bringing back this thread from the dead (September 2005, http://lists.alioth.debian.org/pipermail/nut-upsdev/2005-September/000150.html), however my problem seems relevant enough that I wondered what happened to this thread as it seems to have died after the message I quote below. Despite the fact that I am having trouble getting my Sweex 1000VA UPS (USB) to work, and

Hi all, I am probably missing something ultimately obvious, but I have a problem configuring freepbx... Using Edgy Eft with the cvs freePBX 2.2.1 and followed the Ubuntu installation guide on freepbx.org. System pxe-boots from a server with NFS root on same Using * 1.2 current (from source, not .deb's) Using mISDN-streams (from source, not .deb's) Using freePBX-2.2.1 (from source, not

Does this require a new entry in scripts/hotplug/* and scripts/udev/*? -- Peter Alexander Gordeev wrote: > > Author: agordeev-guest > Date: Sat May 26 12:04:26 2007 > New Revision: 924 > > Log: > data/driver.list: added SVEN Power Smart RM 2000 to the list. > > Modified: > trunk/ChangeLog > trunk/data/driver.list > > Modified: trunk/ChangeLog >

I am trying to move from IAX2 to SIP for voipbuster, moving at the same time to sip1.voipbuster.com. When I try calling out, I see that there is SIP exchange, and in many cases also RTP data being exchanged. Hover in a very large number of attempts the connection is not established. Half of the time there is no RTP, the rest of the time there *is* RTP data flowing in two ways, but no ringtone is

Hello, I am trying to make my UPS system working with NUT but with no success. I got "No supported UPS detected" message. I use the blazer_usb driver since it was proposed to me by the web site. My NUT version is : 2.7.1 (installed from standard RPM), release 2.41 The UPS identification: INFOSEC X4 RM PLUS linux-2qya:~ # /usr/lib/ups/driver/blazer_usb -a infosec Network UPS Tools -

A couple of years ago, Arnaud helped me get my Apollo Line Interactive UPS working, using the blazer_usb driver. Now I've run into another problem, having rebuilt my HP Proliant Microserver into an ESXi 5.5 managed hypervisor with various VMs. One of the VMs is a FreeNAS server which manages the storage for the other VMs so graceful shutdowns are important. I built a single VM to monitor the

Hang on.... there's a non commercial G729 codec that will work with Asterisk? Can someone point me to where I can find it? Thanks, Doug. -----Original Message----- From: Francesco Peeters (Asterisk) [mailto:francesco@fampeeters.com] Sent: Sun 1/22/2006 8:27 AM To: Asterisk Users Mailing List - Non-Commercial Discussion Cc: Asterisk Users Mailing List - Non-Commercial Discussion

Yep I did the same. -----Original Message----- From: asterisk-users-bounces@lists.digium.com [mailto:asterisk-users-bounces@lists.digium.com] On Behalf Of Francesco Peeters (Asterisk) Sent: Saturday, 21 January 2006 5:34 PM To: fbraeuer@gmail.com; Asterisk Users Mailing List - Non-Commercial Discussion Cc: Asterisk Users Mailing List - Non-Commercial Discussion Subject: Re: [Asterisk-Users]