similar to: Not getting nut to work with Eaton 5115

I recently purchased a UPS from http://www.microcenter.com/product/470131/5E_1,100W_2,200VA_6-Outlet_UPS It's sold as an Eaton 5E 1,100W 2,200VA 6-Outlet UPS SKU: 147140 Mfr Part #: 5E2200USB-LA UPC: 743172064875 "The Eaton 5E is an essential line interactive UPS that provides cost effective and reliable power protection against power outages and bad power quality. Thanks to its small

Hi, I'm trying to get a Powerware 5115 to communicate with the NUT via USB under Debian Linux and need help. Here is the output that I see. co-nh5:/tmp/mnt/projects/pwusb/nut-2.4.1# /usr/local/ups/bin/upsdrvctl -u root start Network UPS Tools - UPS driver controller 2.4.1 Network UPS Tools - BCMXCP UPS driver 0.21 (2.4.1) USB communication subdriver 0.17 Communications with UPS lost:

On Oct 25, 2016, at 8:08 PM, Michael Evans wrote: > > It seems that the UPS I bought is actually served by the blazer_usb driver. > > USB ids 06da:0003 (lsusb DB thinks it's a "Phoenixtec Power Co., Ltd 1300VA UPS", but this has apparantly been re-used by Eaton 5E2200USB-LA) > > It's sold as an Eaton 5E 1,100W 2,200VA 6-Outlet UPS > > SKU: 147140 Mfr

It seems that the UPS I bought is actually served by the blazer_usb driver. USB ids 06da:0003 (lsusb DB thinks it's a "Phoenixtec Power Co., Ltd 1300VA UPS", but this has apparantly been re-used by Eaton 5E2200USB-LA) It's sold as an Eaton 5E 1,100W 2,200VA 6-Outlet UPS SKU: 147140 Mfr Part #: 5E2200USB-LA UPC: 743172064875

So, I have this Mustek Powermust 600USB (no serial port) here temporarily. It seems to be a hid device. The output from "lsusb -v" and "newhidups -DDDDD" (with "generic" and "vendorid=06da") are (respectively): ----------------------------------------------------------------------------------------------- Bus 001 Device 002: ID 06da:0003 Phoenixtec Power

I have an UPS, that claims to be IPPon Back Power Pro 700. I'm trying to connect it using USB. lsusb -v says: Bus 1 Device 3: ID 06da:0003 Phoenixtec Power Co., Ltd Device Descriptor: bLength 18 bDescriptorType 1 bcdUSB 1.10 bDeviceClass 0 (Defined at Interface level) bDeviceSubClass 0 bDeviceProtocol 0

Hi! all. I have been reading every mail and news about nut and 06da:0002 Phoenixtec but not found a solution. I have a very nice working ups from: CENER ref: "Active 1000VA 230V 12 CENER" and front logo "LA 900" It has COM3 and USB plugs, I don't know if it needs a standar RS232 I have test with varius drivers in ups.conf [MyUPS] driver = bcmxcp_usb | usbhid-ups |

Hi, I have a powermust with a usb connector. I searched the archive and found this post: http://lists.alioth.debian.org/pipermail/nut-upsdev/2006-April/000816.html Must I abandon hope of controlling this UPS via USB with NUT? Added this line to /etc/udev/rules.d/70-nut-usbups.rules: # OMRON - usbhid-ups SYSFS{idVendor}=="06da", SYSFS{idProduct}=="0003",

Hello, ppl! I try configure NUT for communicate with my Powerware 5115 UPS. As root I run '/lib/nut/bcmxcp_usb -DDDD -u root -a ups', but driver can't connect to my UPS. Some output: Network UPS Tools - BCMXCP UPS driver 0.10 (2.0.4) debug level is '4' usb_set_debug: Setting debugging level to 3 (on) usb_os_init: Found USB VFS at /dev/bus/usb usb_os_find_busses: Found 001

Hi Rok, I retired from working on NUT a few months ago, so I don't have the most up-to-date info. But the guys on the nut-upsdev mailing list (cc'd above) are very helpful. Both of your devices (or nearly identical ones) have been seen on the mailing lists before. The Sweex was first mentioned in a message by Eli Wapniarski on 14 Jun 2006 on nut-upsuser, and was most recently discussed

Roman, I don't think I already asked, but could you post the output of lsusb -v -d 06da:0003 Just to be sure that we're not exceeding some buffer limitations of the device. Best regards, Arjen -- Please keep list traffic on the list

Hello, I have a Yunto e a Zanto ups connected with usb with id 06da:0002 and 06da:0601. I have seen that people had some success using megatec driver. But now megatec is replaced by blazer-usb and I am not able to use my upses under nut. Can you help me? Thanks! Mario

Greetings Gentlemen, I have Mustek NetGuard 1000 UPS which is equivalent to Ippon SmartWinner 1000. I have tried to run several latest builds of NUT, but run megatec_usb driver still failed with my device. I hope the information below might help. Regards, Oleg Here is the information which may help: lsusb -v Bus 002 Device 002: ID 06da:0003 Phoenixtec Power Co., Ltd Device Descriptor:

Hi, I'm having a hard time configuring a Mustek Powermust 600VA ups to work via USB with nut. I read somewhere that nut works OK via the rs232 cable, but unfortunately I don't have a COM port in my computer. The kernel detects the ups as an Xbox pad :) and loads the xpad module. I tried running /lib/nut/megatec with different /dev/ttySx but it displays megatec protocol UPS was not

Hello: I have a UPS model MXE II MAXIM brand online, 3500VA 2100W. Connects to the PC by a USB 2.0 port. I wanted to use nut, but this brand is not on the list of nut drivers. lsusb returns: ... Bus 003 Device 003: ID 06DA: 0201 Phoenixtec Power Co., Ltd ... I did not find this manufacturer in the driver list. Anyone know if you can have compatibility with other make and model of UPS. With

I was unable to setup |nut| on a server for the UPS Eaton 5E with USB connection. All results what did I get was that driver is not running and UPS is not recognized. What kind of driver is suitable for me and what kind of settings? Unit is Eaton 5E. result of |$ lsusb -v| |Bus 004 Device 007: ID 0463:ffff MGE UPS Systems UPS Device Descriptor: bLength 18 bDescriptorType

I recently took over maintenance of a linux computer which is drawing power from a "Maruson Power Net 1500" UPS. However, there is currently no monitoring or control of the UPS by this (or any other) computer. Can nut control this device? There are serial, usb, and EPO connectors on the back of the unit. (There may be a manual but I'm going to have to hunt for it.) Thanks, David

Hello i tried to connect my netys 2000 pr ups to ubuntu 11.10 and i have a problem connecting it. After readin a few post i realized to dianosse the connection. I need help resolving the connextion issue So here is the response to??/lib/nut/usbhid-ups -u root -DDDDD -a netys: Network UPS Tools - Generic HID driver 0.35 (2.6.1) USB communication driver 0.31 ? ?0.000000 ? ? send_to_all: SETINFO

Hi NUT Users, One of my APC UPS is having battery issue and apparently we cannot change battery in that UPS. (not super green?) I have purchased an EATON UPS and added the ref in ups.conf When restarting the driver, I got this error > 0.030612 [D2] Checking device 2 of 10 (0463/FFFF) > 0.287659 [D2] - VendorID: 0463 > 0.287853 [D2] - ProductID: ffff >

On 06/19/2017 05:33 PM, Charles Lepple wrote: > On Jun 19, 2017, at 4:27 AM, Manuel Wolfshant wrote: >> 1.014501 [D2] Unable to get HID descriptor (Pipe error) >> 1.014511 [D3] HID descriptor length (method 1) -1 > So at this point in the logs, the kernel USB HID driver is detached from the UPS HID interface (until the UPS USB cable is unplugged and reattached). If