similar to: Liebert IntelliSlot Unity Card IS-UNITY-DP snmp UPS-MIB.upsIdentManufacturer '1.3.6.1.2.1.33.1.1.1.0' problem

Hi John, do you have the device (which one? An old SNMP WEB or new UNITY DP or something else?) Or you like to buy one? If you have (or you can buy) the old one SNMP WEB - then nut should work fine with it via generic snmp driver and you don't need anything else. If you have (or you must buy) the new one UNITY DP - then I can share my snmp subdriver for it, and you should insert this

Dear All, I have configured Cluster Suite with 2 servers Server 1 : 192.168.13.110 IP Address Server 2 : 192.168.13.179 IP Address Floating : 192.168.13.83 IP Address (Assumed by currently active server) I want all snmp packets going out through the active server to be stamped with floating IP So i have added a iptables rules as "iptables -t nat -A POSTROUTING -p udp -s

On 02.10.2014 03:42, Charles Lepple wrote: > On Oct 1, 2014, at 5:07 AM, Tarvo.Tiits at automaatika.ee wrote: > >> Why is ups.status empty? > If I understand the commit log for SVN r3590, then that revision was supposed to set the status to OL if the numeric state was 9 for ECO mode. It does not appear to do that: > >

Good morning, I just had the chance this morning to get my linux box tied into our network and talking to the UPS. I can now confirm that in NUT v2.4.3 snmp-ups (ietf) works with the Liebert Intellislot Web Card for the GXT2 family of UPS'. upsc output: tux ~ # upsc workups at localhost battery.charge: 100.00 battery.runtime: 2760.00 battery.runtime.low: 5 battery.voltage: 54.60 device.mfr:

Good morning, I just had the chance this morning to get my linux box tied into our network and talking to the UPS. I can now confirm that in NUT v2.4.3 snmp-ups (ietf) works with the Liebert Intellislot Web Card for the GXT2 family of UPS'. upsc output: tux ~ # upsc workups at localhost battery.charge: 100.00 battery.runtime: 2760.00 battery.runtime.low: 5 battery.voltage: 54.60 device.mfr:

Hi I''ve patched net-mrtg http://www.net-snmp.org/ with http://x-ray.prokon.cz/data/snmp/ sucefully Also I''ve copied QOS.TXT to /usr/local/share/snmp/mibs when I make a normal use of snmp, with mrtg in order to monitor all traffic on eth0 and eth1, it works OK. But, how must I do in order to get monitor for a specific class ? If I make a snmpwalk (like README suggest), I get

Hello I'm trying to setup SNMP on my Centos 4.2 server. I want the ability to monitor the disk and some other non default settings that can be defined in snmpd.conf but when I request the data, it doesn't give the disired results. Config below and trap results below. Thanks in advance for any help. Kevin [root at localhost snmp] snmpget -v 2c -c public localhost disk

Hi all, I hope someone can help me with this one. I'm trying to graph all traffic on the localhost's network card with Cacti. >From what I understand I should use SNMP to query the traffic, but I can't seem to get SNMP info for the network interface. I have installed all the necessary snmp tools, "yum install snmpd net-snmp net-snmp-utils net-snmp-devel net-snmpt-libs "

Hi, Just started using NUT with a Liebert PSI-XR 3000 with an Intellislot web card. It seems I can't get it to run properly. I am using NUT 2.6.0 built from source on Ubuntu 8.0.4 . My build parameters are : ./configure --enable-strip --with-linux-hiddev=/usr/include/linux/hiddev.h --with-udev-dir=/lib/udev \ --prefix=/usr \ --exec-prefix=/ \ --sysconfdir=/etc/nut \

Hi, This appears to be related to a thread from January 2010: http://lists.alioth.debian.org/pipermail/nut-upsdev/2010-January/004470.html NB: This is on an HP-UX 11.31 box, using a self compiled and packaged version of NUT 2.6.3, and net-snmp v5.7.1. Therefore some of the search paths and things like that may well be wrong because I've done something dumb. I'm also only just getting

On Oct 2, 2014, at 1:53 AM, Tarvo Tiits <Tarvo.Tiits at automaatika.ee> wrote: > On 02.10.2014 03:42, Charles Lepple wrote: >> On Oct 1, 2014, at 5:07 AM, Tarvo.Tiits at automaatika.ee wrote: >> >>> Why is ups.status empty? >> If I understand the commit log for SVN r3590, then that revision was supposed to set the status to OL if the numeric state was 9 for

nut-2.6.5 Scientific Linux 6.3 APC AP9630 management card My basic question is, does nut's SNMPv3 implementation work? I have this in /etc/ups/ups.conf ...... [tfapc01] driver = snmp-ups port = tfapc01.testfest.ixorg.org mibs = apcc snmp_version = v3 secLevel = authPriv secName = tfsnmpprof1 authPassword = ralow6moHet7zoboP8 privPassword = tuseL8Pakaz9degim7 authProtocol=MD5

G'day I'm currently using NUT on Debian squeeze box in the same subnet with an IBM 3000 HV (branded Eaton 5125 with Web/SNMP card), now I wanted to get our storage appliance running NexentaStor 3.1 set up to be using NUT too. Nexenta- Stor is an OpenSolaris / illumos-based appliance OS currently using NUT packages from ubuntu hardy. My question here is whether I'm running into a -

Couple of little things I noticed with a new RELENG_7 AMD64 box (as of yesterday) ifstat from the ports cannot seem to find interfaces for some reason ? It works fine on i386 [ns8]# ifstat -b ifstat: no interfaces to monitor! [ns8]# [ns8]# ifconfig em0: flags=8843<UP,BROADCAST,RUNNING,SIMPLEX,MULTICAST> metric 0 mtu 1500

Hi all! I know this is quite offtopic, but I found nothing in google nor in the net-snmp mailing list, and I know there''s a lot of people here graphing with snmp+rrdtool. I installed net-snmp 5.1.2-6.1 in Debian to produce graphs for some ethernet interfaces. It seems it''s not reporting correct values for them. Here''s my snmpd.conf (very simple) and the output from the

How might I discover, via SNMP, which boxes are running libvirt-snmp? Performing a walk from the top seems to skip the Libvirt MIB ... (why is this?) ~/walk$ snmpbulkwalk -c public kvmtestbox .iso | more SNMPv2-MIB::sysDescr.0 = STRING: Linux kvmtestbox.company.com 2.6.32 -358.23.2.el6.x86_64 #1 SMP Wed Oct 16 18:37:12 UTC 2013 x86_64 SNMPv2-MIB::sysObjectID.0 = OID: NET-SNMP-TC::linux

-----BEGIN PGP SIGNED MESSAGE----- Hash: SHA1 I figured out why nut seemed to segfault at startup from my Solaris boxes (and snmp-ups too) - I believe that nut is trying to use some MIBs that do not exist on my particular PW9170, for whatever reason. It dies on my Linux box too, complaining like this: pkdick:~/nut/bin# ./snmp-ups -x mibs=pw -x community=publicstring upsname Network UPS Tools -

I have a Cisco 6509 switch that I'm monitoring with SNMP from a CentOS5 machine. SNMP polls are the only access I have to this device, we are not allowed to log on via telnet. How can I find out which port on the switch a particular server is connected to? I was hoping that this is somehow possible using the mac address and the data gathered from snmpwalk/snmpget requests but I'm not

I did a bunch of work on this today. It should be all set to go. This patch is to add support for the Cyberpower RMCARD snmp cards. I basically copied the driver for bestpower, changed the name and updated the mib map. I have this running on two separate systems (two separate ups's) and it looks good. The only thing I could not figure out was updating the Makefile.am (my aclocal/libtools

I'm in the process of trying to get NUT to manage an APC SmartUPS. Monitoring of the UPS is working fine: $ upsc nutdev1 at localhost Init SSL without certificate database ambient.1.humidity.alarm.high: 60.00 ambient.1.humidity.alarm.low: 30.00 ambient.1.temperature.alarm.high: 40.00 ambient.1.temperature.alarm.low: 10.00 battery.charge: 94.00 battery.charge.restart: 0 battery.current: 0.00