similar to: Problem connecting to APC Smart UPS SC1000 on Windows

Hello, I am not able to get NUT working with a APC SC1500. The ups has only a serial port and came with a 940-0272a serial to usb cable. The cable has a fake Prolific chip in it, so only works by downgrading the driver to version 3.2. I tested a 940-0024C cable without success as well. The ups works with powerchute and apcupsd with the 940-0272a cable. Have not tested it with the other one. OS:

Hi, I have a bunch of UPSs, most connected to pcs with Linux working 100% with NUT. The only one I have a problem with, is connected to Windows 7 64bit, and I used the straight MSI installed from the website named NUT-Installer-2.6.5-4.msi Took me a while to find a way to get it to work, but it is ugly for now. Just starting up the service results in a NUT not working at all, and I tracked it

Dear Ladies and Gentlemen, I have several old, yet functioning APC Smart-UPS (Model 600LS, Part AP600I, Firmware 6JI, no EEPROM, from 1991). They are not supported by Powerchute any more. I run NUT 2.6.5-4 on Windows XP SP3. I use COM1 port with cable 940-0024C. The connection fails with APC Smart protocol driver 3.0 (2.6.3-3534:3540M), APC command table version 3.0 or higher - it works with APC

Ok, so I previously thought I had to use usbhid-ups but when I eventually got it going this is what I got:- This Powercom device (0d9f/0002) is not supported by usbhid-ups. Please use the 'powercom' driver instead. So I switched to the powercom driver, but I have tried a whole bunch of likely suspects for the port setting, none of which have worked Tried so far:- com1 with these

Hello all, been 5 years since I posted on this list, glad to be back :) I have a number of X-power Tigra 1kVA online UPS units. From some knowledgeable folks working for the local distributor, I learnt that from inside this looked like a Best 610 ups unit. Before, I had this UPS hooked via serial to my Windows 2003 server. For monitoring, some winpilot/upspilot software was also provided.

Hello all, long time away from this list, glad to be around again! I have this Powercom Vanguard VGN VGD-20K31. Some details of this model: * 3-phase input, single phase output * Model has 240V / 12V9AH x 20 x 2SET, plus another set of 20 batteries. All in all, 3 sets * Serial connection to Windows 2k3 server with UPSMon Now I was strongly considering replacing the bundled no-good upsmoon

On several occasions I have seen the apcsmart process runaway using 100% CPU while filling my syslog partition by logging the following syslog entries at an incredible rate. I have seen up to 21,800 log entries PER SECOND of the following nature: --[snip]-- Jun 25 10:06:38 servername apcsmart[4012]: Communications with UPS lost: Communications with UPS lost - check cabling Jun 25 10:06:38

Hi Alex, since I have no knowledge of the apcsmart driver, nor much time currently, I've forwarded your msg to the NUT development list. I hope somebody can take over your call. btw, please subscribe to the list for further discussions... 2007/5/28, Alex Brodsky <abrodsky at acs.uwinnipeg.ca>: > Hi, > > My name is Alex Brodsky, I am a faculty member at University of >

2011/2/15 Lupe Christoph > On Monday, 2011-02-14 at 21:54:20 -0000, Arnaud Quette wrote: > > I definitely need more info! > > please reply to ALL: > > > - what is the exact model and date of manufacturing? > > SmartUPS 300I NET. I have the serial number (GS9809283199) but no date. > it seems to be a recent model. > - are you sure this unit is ok? > >

2011/2/15 Lupe Christoph > On Monday, 2011-02-14 at 21:54:20 -0000, Arnaud Quette wrote: > > I definitely need more info! > > please reply to ALL: > > > - what is the exact model and date of manufacturing? > > SmartUPS 300I NET. I have the serial number (GS9809283199) but no date. > it seems to be a recent model. > - are you sure this unit is ok? > >

[BackUPS] driver = apcsmart port = /dev/ttyS0 desc "Back-UPS BK-300 @ Cap a l'orignal" > ----- Original Message ----- > From: "Charles Lepple" <clepple@gmail.com> > To: "NUT-MList" <nut-upsdev@lists.alioth.debian.org> > Sent: Monday, June 19, 2006 2:38 PM > Subject: Re: [Nut-upsdev] Backups 300VA (BK-300C) Drivers >

On 2014-01-14 10:12, dstrr wrote: > Hello. > Trouble to communicate with APC SmartUPS via serial port. > UPS connected to the com1 port on windows host. > Communication witch hyperterm works well. > There is a log: > > YSM > ^ASmart-UPS SC1000 > n5S0713T63247 > m03/29/07 > L240.0 > B27.10 > > apcupsd also can communicate with the UPS and works well. >

Running Samba 2.0.6, on Sun SC1000 (4 CPUs) with Solaris 2.6 smbd processes don't seem to terminate although the connections don't show-up with netstat. The client session seems to terminate, and the connection is terminated, but the smbd process seems to hang around waiting. smb.conf specifies "deadtime=5", and in most cases there is no open file associated with the smbd

Hello. Trouble to communicate with APC SmartUPS via serial port. UPS connected to the com1 port on windows host. Communication witch hyperterm works well. There is a log: YSM ^ASmart-UPS SC1000 n5S0713T63247 m03/29/07 L240.0 B27.10 apcupsd also can communicate with the UPS and works well. running apcsmart -a ups gives the following: com1: device reports different attributes than what were set

Hello! I've ran into this annoying issue when setting up a new server. I have an APC SmartUPS hooked up on a USB-serial converter on /dev/ttyUSB0. This works nicely, until: hub 3-0:1.0: port 1 disabled by hub (EMI?), re-enabling... pl2303 ttyUSB0: pl2303 converter now disconnected from ttyUSB0 usb 3-1: pl2303 converter now attached to ttyUSB1 apcsmart gets into an infinite loop of this:

I have a new APC Smart-UPS SUA2200RM2U. I've had no success with the manufacturer's PowerChute software and smart signaling, so I have decided to try NUT. The smartups driver can't make contact through the serial port. Since this is rack-mounted, it comes with a 940-1524 serial cable. As far as I can tell, this is supposed to work with smart signaling. Here's my ups.conf:

I have only RS-232 on the box (meanwhile, it was manufactured on march of 2011) Here is my configs: nut.conf: * * MODE = netserver ups.conf: * * [KIN1500] driver = powercom port = notUsed desc = "Powercom KING PRO KIN-1500AP RM" upsd.conf: * * LISTEN 192.168.1.2 3493 upsd.users: * * [monuser] password = xxxxxxxx upsmon master

Hi, What driver should i use with APC BK-300C ? Michale Plourde Digicom Technologies

This patch introduces a handful of new options, I mentioned earlier in: http://www.mail-archive.com/nut-upsdev at lists.alioth.debian.org/msg02088.html See the large commit message in the follow-up for the details and rationale. I realize it's a bit larger diff - so if it's required I can split it into few smaller ones. Michal Soltys (1): APC smart driver update and new features.

This is 2nd version of the earlier patch featuring a few new features and fixes to the apcsmart driver, following the remarks in: http://www.mail-archive.com/nut-upsdev at lists.alioth.debian.org/msg02294.html Major changes from v1: - handle battery.charge and battery.runtime checks at main.c level - handle "immutable but writable" conflict gracefully at driver level -