similar to: dahdi_scan

Hi everybody, In an Asterisk 1.6.0.5, dahdi-linux-2.1.0.4, dahdi-tools-2.1.0.2, with a Digium B410P and an OpenVox A400E, I can't make "dahdi_scan" to recognize the OpenVox. This card was working correctly but suddenly stopped working and I cannot make it work again. Both ?lspci? and ?dahdi_hardware? detect it but ?dahdi_scan? not and I cannot use it. >lsppci: *0a:00.0

Hi, On a Lenny system, with dahdi 2.4.0, libpri 1.4.11.5 and asterisk 1.6.1.18, I inserted a new Digium HA8 + B400M card. My usual installation fails. I can see it listed : # lspci -n | grep d161 01:0b.0 0200: d161:8007 (rev 11) # lspci -vn 01:0b.0 0200: d161:8007 (rev 11) Subsystem: d161:8007 Flags: medium devsel, IRQ 22 I/O ports at d400 [size=256] Memory at

I am trying to get a zaptel install converted to dahdi. I can get dahdi installed, and the pseudo device even shows up; however, dahdi show channels shows me nothing. There is a TE122 and a TDM800 in there, and neither show up. dahdi show status shows both cards, and dahdi tools show that the cards are there, working, and have no alarms. What am I missing? Michael Munger, dCAP, MCPS, MCNPS,

I have setup a asterisk with freepbx, a TE122 and i have an ISDN. My problem now is that callers are experiencing echo. checked on dmesg i saw this: # dmesg -c dahdi: Disabled echo canceller NLP because of CED rx detected on channel 2 i searched google but found no soolution and i have no idea what that error means. below are other details that might be of value. # dahdi_hardware

Hi, Built a new server at the weekend and install Asterisk 1.6.0.9 and IAX and SIP work great :) The one problem I am having is getting the OpenVox (TDM400 type card) to work. It is successfully identified using WCTDM kernel module and dahdi_scan picks it up just fine. The issue is when I try and setup dahdi_channel.conf as it fails everytime. When running asterisk -rvvvv I see the port pick

Hello, After installing on Ubuntu 10.04 using the tutorial on http://hmontoliu.blogspot.com/2010/03/installing-asterisk-and-freepbx-on.html I have a running instance of Asterisk. PROBLEM: result of dahdi_cfg: DAHDI Tools Version - 2.2.1 DAHDI Version: 2.2.1 Echo Canceller(s): MG2 Configuration ====================== Channel map: Channel 01: FXS Kewlstart (Default) (Echo Canceler: mg2)

Hello, I am trying to install my E1 card to make a conection with an Ericsson MD-110 PBX. I installed dahdi drivers as: dahdi_hardware pci:0000:04:08.0 wcte12xp- d161:8000 Wildcard TE121 ran dahdi_genconf and it created all my e1 ports. On the other side i also configured the pbx to communicate with TE121. On ericsson side, i have no error messages. On asterisk side, no error messages. But

Hi, We have got a new PRI card at one of our Office locations and now I need to install the the device on a remote server. Is there any way to know if the device is loaded already. When I give " cat /proc/zaptel/* " it returns the following. # cat /proc/zaptel/* Span 1: WCT1/0 "Wildcard TE122 Card 0" (MASTER) B8ZS/ESF RED IRQ misses: 2 1 WCT1/0/1

Hello, I just made a asterisk / dahdi fresh install on Debian 8.4, and ended up with the following packages : $ sudo dpkg -l|grep -Ei 'dahdi|asterisk|libpri' ii asterisk 1:11.13.1~dfsg-2+b1 amd64 Open Source Private Branch Exchange (PBX) ii asterisk-config 1:11.13.1~dfsg-2 all Configuration

2017-03-14 15:26 GMT+01:00 Tzafrir Cohen <tzafrir.cohen at xorcom.com>: > On Tue, Mar 14, 2017 at 02:58:07PM +0100, Olivier wrote: > > 2017-03-14 13:08 GMT+01:00 Tzafrir Cohen <tzafrir.cohen at xorcom.com>: > > > > > On Tue, Mar 14, 2017 at 11:10:57AM +0100, Olivier wrote: > > > > Hello, > > > > > > > > After all these years

Hello I'd like to configure Asterisk so that... 1. I ring it from my cellphone with CID number displayed, just to notify Asterisk that I wish to make a call 2. Asterisk waits until I hang up, calls me back, and prompts me for the number I wish to call 3. Asterisk puts me on hold through Flash(), which is apparently the equivalent of hitting the R key on European handsets 4. Asterisk calls the

Tengo en una maquia ubuntu 8.10 el kernel es Linux 2.6.27-14-generic Quiero configurar una tarjeta x100p i usarla con asterisk, asi que descague compile e instale lo siguiente: asterisk-1.4.24 dahdi-linux-2.1.0.4 dahdi-tools-2.1.0.2 libpri-1.4.9 Sin embargo no logro configurar la tarjeta con exito, ya probe casi? todo. Esto aparece si ejecuto lspci: 04:06.0 Communication controller: Motorola

Hi All, I have a TE121P card installed and since connected it to the PRI I keep getting the Current Alarm as continually changing from Blue Alarm/Recovering and Recovering. The config I have is: /etc/dahdi/system.conf bchan=1-15,17-31 dchan=16 echocanceller=mg2,1-15,17-31 loadzone = cn defaultzone = cn /etc/asterisk/chan_dahdi.cfg [channels] Context=telco

Does anyone know if I could use modprobe command to find out rather than set the jumper on a Digium PRI card? I want to find out the jumper settings on the card without opening the box which will cause down time. Thanks. -------------- next part -------------- An HTML attachment was scrubbed... URL:

Hi, When typing dahdi_scan on an OctoBRI-enabled setup, I've got only 8 replies such as : [1] active=yes alarms=RED ... [8] active=yes ... framing=CCS I would expect 16 replies (one per B-channel). Is this correct ? Regards -------------- next part -------------- An HTML attachment was scrubbed... URL:

I just installed a TE820 octal span T1 card, and it's not showing up in dahdi_hardware output. This was installed into a test machine that already has a TDM800P card in it, and that one is showing up and working fine. Is there some kernel module that I'm missing? Lspci: 05:04.0 Ethernet controller: Digium, Inc. Wildcard TDM800P 8-port analog card (rev 11) 21:08.0 Communication

Hello folks. I've got a strange issue. When I modprobe TE220 I do not see mesages like Launching card: 0 <..> Setting up global serial parameters. You can see how I loaded and unloaded the card for several times - http://asteriskpbx.ru/pastebin/11 lspci can detect the card: 03:08.0 Communication controller: Digium, Inc. Device 0220 (rev 02) dahdi_hardware also: astpbx ~ # dahdi_hardware

2017-03-14 13:08 GMT+01:00 Tzafrir Cohen <tzafrir.cohen at xorcom.com>: > On Tue, Mar 14, 2017 at 11:10:57AM +0100, Olivier wrote: > > Hello, > > > > After all these years installing from source, I'm giving Dahdi package > > installation a try on a recent Stretch box. > > > > Google over the web, I didn't find too many doc on this topic. >

Hi list, After a lot of testing + troubleshooting, I guess I'm observing what I am now calling a regression with zaptel 1.4.10 (is it?) As such I call for peer feedback, before either asking Digium install support or filing a bug. Thanks in advance! System: HP Proliant DL380 G5 with 2x PCI-X + 1x PCIe riser card OS: Centos 5 Kernel: 2.6.18-53.1.14.el5 (also tested under

Hi All I'm having some serious kernel panic while using digium cards. It may be related to IRQ shared. Can this cause a lot of drop call and bad voice quality ? Do you guys know if there is a way I can assign one IRQ for each digium card ? Thanks a lot. Here is the output of /var/log/syslog kernel: [ 3821.982893] Uhhuh. NMI received for unknown reason 20. kernel: [