similar to: Seeking advice about ISDN BRI Cards

Checkout Beronet ISDN cards and Berofix Gateway (appliance or pci card) Personally for my last installation I chose Berofix card which is rock solid and reliable, yet easily configurable. With berofix you don't need telephony drivers on the host system, the isdn card is detected as a NIC and all configuration is done using a web interface. Then you configure FreePBX a new trunk to use the

2015-05-26 12:17 GMT+02:00 Lukasz Sokol <el.es.cr at gmail.com>: > Hi, > please whoever has some expertise in choice of BRI ISDN cards, > please restore my faith in community support :) > > (on private email I can probably explain more than fits for a public forum) > > Most I'd like to ask is about what to choose, out of what is available... > > My locality is

Thank you all for valuable input, another question: when do I actually need the echo cancellation (hardware / on board /on module ) ? Lukasz On 26/05/15 11:17, Lukasz Sokol wrote: > Hi, > please whoever has some expertise in choice of BRI ISDN cards, > please restore my faith in community support :) > > (on private email I can probably explain more than fits for a public

Hello, Junghanns and BeroNet offer 8 BRI ports cards. Do you know if Digium's B410P has an inner TDM bus so that an 8 BRI ports subsystem (2 PCI slots used, but 1 one set of interrupts) could be made out of 2 B410P ? I know you could (theorically) do this with Junghanns and BeroNet cards. Cheers -------------- next part -------------- An HTML attachment was scrubbed... URL:

Lukasz Sokol wrote: > but have you considered a web-managed config-builder such as FreePBX? > Instead of building your dialplan from scratch ? I've never used FreePBX, but, after having looked at its website, I think I have a general understanding of what it can do. What I don't understand is how FreePBX answers my question about the Linksys SPA3102 being good for a mission

Hi, folks: I remain intrigued by the gap in BRI implementation between North America and Europe, and I wanted to get feedback from the list members on the matter. I'm seriously considering making the leap in our office. In Europe, the idea that an office that does not have enough lines to justify PRI would use analog lines is perceived as technologically backwards, and yet that's what

Hi, (please excuse me for lack of proper jargon usage and the vagueness of description...) i use Asterisk 11.12.1, (well... as included in FreePBX), I have several extensions that can register 2 separate devices (chan_sip) ( FreePBX calls this Devices & Users mode : Users are extension/internal number, devices are the 'SIP Accounts' for the internal 'endpoints' ) (this

Hi everybody, In an Asterisk 1.6.0.5, dahdi-linux-2.1.0.4, dahdi-tools-2.1.0.2, with a Digium B410P and an OpenVox A400E, I can't make "dahdi_scan" to recognize the OpenVox. This card was working correctly but suddenly stopped working and I cannot make it work again. Both ?lspci? and ?dahdi_hardware? detect it but ?dahdi_scan? not and I cannot use it. >lsppci: *0a:00.0

Hi, Has anyone information about BRI hardware supported by 1.6 libpri ? In another thread, I was told a basic BRI card with HFC chipset (Bewan Gazel 128) was supported but I would delighted to lear about other harwarde (and specifically about Digium B410P). Regards -------------- next part -------------- An HTML attachment was scrubbed... URL:

hello: thanks for Tzafrir Cohen for dahdi testing. I installed dahdi-2.1-r3c svn code and asterisk1-6 for testing OpenVox B400P and junghans card. i fund that there is bug (i think) to dectect NT or TE mode. actually on the board, i set it as TE mode, but after start wcb4xxp, but it show the port is NT mode. to detect the TE mode, I modefy the code in base.c

Hi all, I am having trouble setting the signalling method for the B410P using DAHDI. Asterisk complains that it has never heard of 'bri_cpe' or 'bri_net' - but it doesn't mind having 'pri_cpe' etc. ERROR[4294]: chan_dahdi.c:11327 process_dahdi: Unknown signalling method 'bri_net' Dahdi - dahdi-linux-complete-2.1.0.4+2.1.0.2 Asterisk - 1.4.23.1 Libpri - 1.4.9

Hello all, I'm trying to conect two asterisk servers using two B410p Digium cards. One card on each server. I just setting up the first BRI port on server A as nt_ptp and the first BRI port on server B as te_ptp. I use an ethernet wire to connect the first port of server A (nt_ptp) with the first port on server B (te_ptp) but the port light cotinues blinking on red on both sides once the

Dear all, I know this is more a Digium hardware than an Asterisk issue. Already posted a question at Digium, however also like to see whether anyone in the Asterisk community has encountered the following situation: I installed a Digium B410P BRI PCI card on my new asterisk server, following the steps specified in the manual. I can see the PCI card is available using the lspci command: ...

Hi, At the moment, libpri /w Asterisk 1.6, Dahdi 2.1, is not supporting NT-Point to multi-point mode. Here (France), most small PBXes are connected to ISDN through BRI trunks in PtmP (don't know why but it seems the general case). So this NT-PtmP function would be very helpful to easily slide an Asterisk box between an existing PBX and the network. Does the same case apply elsewhere (UK,

Hi sir, I was installed Goautodial server and I have b410p BRI card. BRI card showing OK with dahdi_tool, this NT mode. whenever I am dialing from server i am not able to connect the call . in Cli below mention warning is comming . please what is the mistake with me . help me Executing [0559566768 at default:1] AGI("Console/dsp", "agi:// 127.0.0.1:4577/call_log") in new

Hi all We use pci/pci-e BRI cards in our installations. Due to echo problems (that was before Oslec and others), we quickly switched to cards with hardware-based EC. So we use exclusively Digium B410p cards that provide 64ms tail EC. For several reasons we'd like to switch to external BRI gateways like the Patton smartnodes (the price is getting really close to a B410p). I'm

Hi list, I installed 2 HB8 cards each of them with a Quad Bri modules in a HP 360 G6 running Debian Squeeze. Here is an output of dmesg wafter server has booted: [ 9.784123] wctdm24xxp 0000:0b:08.0: PCI INT A -> GSI 31 (level, low) -> IRQ 31 [ 11.847073] bnx2: eth0 NIC Copper Link is Up, 1000 Mbps full duplex [ 11.847600] ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready [

I'm trying to get my Sangoma B600 working with Asterisk 1.6.1 and DAHDI 2.2. I've tried running ./Setup dahdi (and with --64-bit_4GB flag, running amd64) and the compile fails with this for many versions of the driver (incl. 3.3.16, 3.3.16.22, and 3.4.1): Building modules, stage 2. MODPOST 1 modules CC /usr/src/wanpipe-3.3.16/patches/kdrivers/wanec/wanec.mod.o LD [M]

Hello, there has been a post to this list somewhere arount april which said that it is possible to use a Sangoma BRI A500 card with zaptel and asterisk bristuff. That is, without sangoma_brid and sangoma_mgd daemons and without woomera channels. Could anybody give me a short hint how to configure this? I tried wanpipe-driver + zaptel + asterisk-bristuffed, but I couldn't get zaptel to

Hello, I'm evaluating to possibility to use chan_misdn as a short term workaround, in case latest Dahdi is not stable enough for what we are planning to do (we wish to use Junghanns and Digium BRI hardware with Asterisk 1.6) . I've read www.mISDN.org but still have a couple of questions : 1. Is correct that in a 2.6.27 (and up) enabled kernel, the "embedded" mISDN version is