similar to: No subject

Hello Team I have installed the new DL580 and used the new TE420B to add capacity on our ivr. Before I put new E1?s I decided to first move the old e1 from the old system to this new one but it has errors which not only affect the audio quality, but also cause the asterisk to refuse any call after sometime even though the channels seems up and active {seems d-channel fails}.. When processing

Hi fellow asterisk users, I am running Asterisk 1.4.29 with an Digium TE121 card (wcte12xp kernel module) an approx. 100 snom320. The whole installation is running without issues since 5 months. Without having changed anything on the asterisk server for at least 2 months, i noticed "clicking sounds" at external calls over the PRI. Asterisk constantly throws the following messages: ...

Hi I am trying to connect asterisk with a Cisco GW 2600 with E1 pri using a Digium, Inc. Wildcard TE210P dual-span T1/E1/J1 card 3.3V (rev 02), Errors: [Jan 28 17:32:33] VERBOSE[6182] logger.c: == Primary D-Channel on span 1 up [Jan 28 17:32:33] WARNING[6182] chan_dahdi.c: PRI Error on span 0: We think we're the CPE, but they think they're the CPE too. [Jan 28 17:32:34] NOTICE[6182]

I am having a problem with a new PRI turn-up on dahdi 2.5.0 and asterisk 1.8.5 that I have not seen before. The PRI is setup as B8ZS, ESF and the span shows up and ok. This PRI is merely a crossover T1 going into an old DC0 class 5 switch. I am getting the following errors over and over again [Aug 16 10:26:10] NOTICE[8002]: chan_dahdi.c:3043 my_handle_dchan_exception: PRI got event: HDLC Bad FCS

Hi, After upgrading to DAHDI 2.4.0 from Zaptel, I noticed a lot of HDLC errors on my console: [Nov 27 01:15:09] NOTICE[2743] chan_dahdi.c: PRI got event: HDLC Bad FCS (8) on Primary D-channel of span 1 [Nov 27 01:15:09] NOTICE[2743] chan_dahdi.c: PRI got event: HDLC Abort (6) on Primary D-channel of span 1 These errors prevented calls from being made and received on my PRI spans. This seems

Hello, I've got a running system in which logs are full of messages such as: [Jun 10 07:24:14] NOTICE[2414] chan_dahdi.c: PRI got event: HDLC Bad FCS (8) on Primary D-channel of span 2 The strange thing is those messages are coming from a single span. My setup is : Asterisk 1.6.1.18 Junghanns OctoBRI with wcb4xxp driver libpri 1.4.10.2 dahdi 2.3.0 3 BRI lines in PtMP mode What does this

Hi all, Last night I went to replace an Asterisk 1.4 + mISDN + b410p box with Asterisk 1.6.2 and DAHDI BRI - to no avail. I had two servers so copied network setting etc from the working one, moved the card across, ran dahdi_genconf etc and it didn't work. Here's the console output with notices disabled: lucas*CLI> pri intense debug span 1 Enabled debugging on span 1 [Dec 16

Hello, I seem to be having an issue with the configuration of my PRI on a new asterisk server I've created to replace an old install that I have. The card is Digium Wildcard TE133. I continually get messages like "Primary D-Channel on span 1 down", rather irregularly: [2013-07-29 17:31:39] VERBOSE[3621] sig_pri.c: == Primary D-Channel on span 1 up [2013-07-29 17:31:39]

Hi, Does anyone have any good empirical data suggesting what the maximum number of PRI calls (incoming and outgoing) without hardware echo cancellation can be handled on a single box is? I have a TE410P T1 (1st gen) card and I'm seeing interesting errors of D-Channels going down and then coming back up (See below). I've looked at the number of simultaneous calls at each of these points,

Is a normal functionality? when I do #dahdi_cfg -vvvvvv In my Asterisk console shows this.... [Jul 24 13:39:08] NOTICE[30263]: chan_dahdi.c:9461 pri_dchannel: PRI got event: HDLC Abort (6) on Primary D-channel of span 1 If I do this a lot of times...then [Jul 24 13:39:20] NOTICE[30263]: chan_dahdi.c:9461 pri_dchannel: PRI got event: HDLC Abort (6) on Primary D-channel of span 1 [Jul 24

Hi all, as good? I am trying to go up a board TE110P with link E1 ISDN PRI to establish connection with a central office Siemens HiPath 4000. But I am having the following errors: Server1:~ # asterisk -r Asterisk 1.2.10, Copyright (C) 1999 - 2006 Digium, Inc. and others. Created by Mark Spencer <markster@digium.com> Asterisk comes with ABSOLUTELY NO WARRANTY; type 'show warranty'

Hi, On a Asterisk 1.8.12 system working OK for months (>100k calls proceed), users are complaining for bad audio. My setup is: PSTN <--E1/PRI ---> Asterisk <--- E1/PRI---> Siemens HiPath <---E1/PRI ---> PSTN asterisk -rx "dahdi show version" DAHDI Version: SVN-trunk-r10414 Echo Canceller: HWEC asterisk -rx "pri show version" libpri version: 1.4.12 A

I just upgraded my asterisk install from january 2005 CVS HEAD to current CVS HEAD : * zaptel * libpri * asterisk My asterisk have one TE405P with one span (the clock source) pluged into a telco PRI E1, a second span is a PRI E1 to another PBX and the third one is a T1 to a rhino channel bank. Everything went smoothly except that the two PRI span restart every ten seconds after some HDLC

Hi, I running into the following problem on my Asterisk setup: --snip-- [Sep 3 01:40:59] NOTICE[9170] chan_dahdi.c: PRI got event: HDLC Abort (6) on Primary D-channel of span 3 [Sep 3 01:47:07] ERROR[9170] chan_dahdi.c: No more room in scheduler [Sep 3 01:47:07] ERROR[9170] chan_dahdi.c: Asked to delete sched id -1??? [Sep 3 01:47:07] ERROR[9170] chan_dahdi.c: No more room in scheduler [Sep

---------- Forwarded message ---------- From: Jan Prunk <janprunk at gmail.com> Date: Sep 13, 2007 3:35 PM Subject: Bad FCS error To: asterisk-users at lists.digium.com Hello ! I am getting the following error in asterisk logs: Sep 11 17:33:30 NOTICE[2187] chan_zap.c: PRI got event: HDLC Bad FCS (8) on Primary D-channel of span 1 Sep 11 21:45:08 NOTICE[2187] chan_zap.c: PRI got event:

Hi Asterisk Users, We've been experiencing some tough time regarding a new Asterisk installation connected to the PSTN via an ISDN PRI with a Digium TE121 with the optional VPMADT032 echo cancellation module. For now, I'll focus on something very specific which is summarized on this email's subject. However, here are some general facts for the context: - System pbxfri went

Hi all, So, we reverted the LibPRI version and tested it, and then tried with the latest version of everything. Still no changes. The BRI line is in PTMP. If we set the configs to PTMP in the genconf_parameters and try it, we get the following: [Jan 21 17:32:20] ERROR[20341]: chan_dahdi.c:12645 dahdi_pri_error: Unable to receive TEI from network! If we set it to PTP (which it is not) we

Hi all. I have this problem with my Digium 2E1 card and PRI, for hours It works well, with some meesages... [Aug 10 09:20:31] NOTICE[32270] chan_dahdi.c: PRI got event: HDLC Abort (6) on Primary D-channel of span 1 But PRI continue up....hours later... PRI go down. I thought the problem was in the telco, but the strange thing is that I have a loop cable in the second E1 and when I scan both E1

Hi everyone, I have been having some problems lately with our PRI and Asterisk, or maybe it is just me. It happens once maybe twice a day, but when some of our customers are calling in, the phone just drops on them. I pulled the information below from the log from one that happened. I notice why it is happening, but I can't seem to figure out a way to stop it from happening. I also

Does anyone have any experience ith configureing the sangoma A102 card for testing using a e1 cross cable i've configured and installed the cards properly even the lights on the card are green which proves that my cross cable is properly built too. my problem is with asterisk which gives me these errors PRI got event: HDLC Abort (6)on Primary D-channel of span 1 PRI got event: HDLC Bad FCS