similar to: Help on UPS Eaton 5E 850i USB

It seems that the UPS I bought is actually served by the blazer_usb driver. USB ids 06da:0003 (lsusb DB thinks it's a "Phoenixtec Power Co., Ltd 1300VA UPS", but this has apparantly been re-used by Eaton 5E2200USB-LA) It's sold as an Eaton 5E 1,100W 2,200VA 6-Outlet UPS SKU: 147140 Mfr Part #: 5E2200USB-LA UPC: 743172064875

On Oct 25, 2016, at 8:08 PM, Michael Evans wrote: > > It seems that the UPS I bought is actually served by the blazer_usb driver. > > USB ids 06da:0003 (lsusb DB thinks it's a "Phoenixtec Power Co., Ltd 1300VA UPS", but this has apparantly been re-used by Eaton 5E2200USB-LA) > > It's sold as an Eaton 5E 1,100W 2,200VA 6-Outlet UPS > > SKU: 147140 Mfr

I recently purchased a UPS from http://www.microcenter.com/product/470131/5E_1,100W_2,200VA_6-Outlet_UPS It's sold as an Eaton 5E 1,100W 2,200VA 6-Outlet UPS SKU: 147140 Mfr Part #: 5E2200USB-LA UPC: 743172064875 "The Eaton 5E is an essential line interactive UPS that provides cost effective and reliable power protection against power outages and bad power quality. Thanks to its small

Hi NUT Users, One of my APC UPS is having battery issue and apparently we cannot change battery in that UPS. (not super green?) I have purchased an EATON UPS and added the ref in ups.conf When restarting the driver, I got this error > 0.030612 [D2] Checking device 2 of 10 (0463/FFFF) > 0.287659 [D2] - VendorID: 0463 > 0.287853 [D2] - ProductID: ffff >

On 06/19/2017 05:33 PM, Charles Lepple wrote: > On Jun 19, 2017, at 4:27 AM, Manuel Wolfshant wrote: >> 1.014501 [D2] Unable to get HID descriptor (Pipe error) >> 1.014511 [D3] HID descriptor length (method 1) -1 > So at this point in the logs, the kernel USB HID driver is detached from the UPS HID interface (until the UPS USB cable is unplugged and reattached). If

Following the instructions a following site I can not get nut to work with my UPS. http://bernaerts.dyndns.org/linux/75-debian/335-debian-wheezy-install-monitor-eaton-ups Hope that you can find out what is wrong by the provided info in the email Best Regards, Magnus Karlsson # lsusb -s 001:005 -v Bus 001 Device 005: ID 06da:0002 Phoenixtec Power Co., Ltd UPS Device Descriptor: bLength

Hello I have a remote Dell R310 to which I connected via USB a new UPS, model Eaton 5E1500I USB. Assuming I interpreted correctly the docs, it should normally work using the usbhid-ups driver. However, no matter what I tried, I get an error which you can also is included in the below paste: #usbhid-ups -DDDD -u root -x explore -x vendorid="0463" -a eaton Network UPS Tools

Hi All, I bought a USB Bluetooth dongle. However, it's not working for me. Please help, how to debug and get more information as I can not see any error or warning message from system log message. I checked http://thread.gmane.org/gmane.linux.bluez.kernel/22183/focus=22211, however, also find another page

Hello list, ? ?Cannot make Evolution 850 to be recognized, maybe the problem is "Warning: incomplete endpoint descriptor" in lsusb? Details are as follows. NUT installed by download of debian package. Any ideas/suggestions are highly welcome, thanks in advance! --ValenteM = ? ?= ? ? = ? ? = Ubuntu server 12.04.1 LTS (GNU/Linux 3.2.0-35-generic x86_64) sudo dpkg -i

Hi, just try the Unitek Self Protek Mistral 1000ipF with nut and I doesn't work. How can I correctly configure it (if the driver support it). Best regards, In my dmesg: [42953293.620000] usb 1-2: new low speed USB device using uhci_hcd and address 7 [42953293.760000] usb 1-2: no configurations [42953293.760000] usb 1-2: can't read configurations, error -22 [42953293.880000] usb 1-2: new

Hi, I have a powermust with a usb connector. I searched the archive and found this post: http://lists.alioth.debian.org/pipermail/nut-upsdev/2006-April/000816.html Must I abandon hope of controlling this UPS via USB with NUT? Added this line to /etc/udev/rules.d/70-nut-usbups.rules: # OMRON - usbhid-ups SYSFS{idVendor}=="06da", SYSFS{idProduct}=="0003",

Hello I have two completely different UPS that turn out to use the same driver. Both work with blazer_usb my LSUSB says: Bus 001 Device 005: ID 0665:5161 Cypress Semiconductor USB to Serial Bus 001 Device 004: ID 0665:5161 Cypress Semiconductor USB to Serial my lsusb -vd 0665: says: pi at elektra:~ $ lsusb -vd 0665: Bus 001 Device 005: ID 0665:5161 Cypress Semiconductor USB to Serial

Hi all! FYI, after some research in your list I think that blazer_usb is the best driver for my Soyntec Sekury A600 UPS (which is not in the hardware supported lists). I connected it with my system using USB port (it also has serial RS-232) This is the report I have: battery.voltage: 13.60 battery.voltage.nominal: 12.0 beeper.status: enabled device.type: ups driver.name: blazer_usb

folks, the following is lsusb -v for my 250gb usb hard drive. I note the Protocol line mentions zip: ie bInterfaceProtocol 80 Bulk (Zip) does that mean its one of those USB-ZIP devices ? If so, to the parameters below say anything about the CHS settings needed ? tia, PS - HPA, you were correct wrt what I missed :-} Bus 001 Device 002: ID 1058:0401 Western Digital Technologies,

Hi everybody, In a christmas sequel I've been offered one of the units mentioned above. I've tried to connect it to my Fedora 8 workstation but rapidly concluded it's not yet supported by NUT. So far, I've decompiled the Java classes of the manufacturer's application and noticed that it's most probably yet another kind of serial protocol through the USB. Since

Hi Rok, I retired from working on NUT a few months ago, so I don't have the most up-to-date info. But the guys on the nut-upsdev mailing list (cc'd above) are very helpful. Both of your devices (or nearly identical ones) have been seen on the mailing lists before. The Sweex was first mentioned in a message by Eli Wapniarski on 14 Jun 2006 on nut-upsuser, and was most recently discussed

Hello, I (now) own an Emerson Liebert GXT3 6000VA conected via USB. I've searched the web trying to configure nut (nut-2.6.5-1.el6.x86_64 epel rpm on CentOS 6.3) to monitor the UPS, but couldn't find a successful configuration. I'm running kernel 2.6.32-279.14.1.el6.x86_64. The UPS is connected with an USB cable: Bus 004 Device 002: ID 10af:0008 Liebert Corp. PowerSure Interactive

Hi, we bought two Smart-UPS X 1500 FW:UPS 09.1 / ID=20 lsusb -v: Bus 002 Device 002: ID 051d:0003 American Power Conversion UPS Device Descriptor: bLength 18 bDescriptorType 1 bcdUSB 2.00 bDeviceClass 0 (Defined at Interface level) bDeviceSubClass 0 bDeviceProtocol 0 bMaxPacketSize0 64 idVendor

Bonjour, Je souheterais utilis? la version qui permet le '-x generic',mais je ne sais pas ou la recuperer car ca devrait solutionner mon probleme (cf mail ci-dessous) DaneZ _____ From: DaneZ [mailto:david.guillotte@danez.no-ip.org] To: arnaud.quette@mgeups.com Sent: Sat, 08 Jul 2006 23:24:06 +0200 Subject: Fw: INFOSEC 500 XP en USB _____ Bonjour Arnaud, Je me

Hi, we bought two Smart-UPS X 1500 FW:UPS 09.1 / ID=20 lsusb -v: Bus 002 Device 002: ID 051d:0003 American Power Conversion UPS Device Descriptor: bLength 18 bDescriptorType 1 bcdUSB 2.00 bDeviceClass 0 (Defined at Interface level) bDeviceSubClass 0 bDeviceProtocol 0 bMaxPacketSize0 64 idVendor