similar to: newbie: Slackware servers w/ AP9617, AP9606

I've successfully installed and configured NUT on my test machine and am moving it into production. http://www.networkupstools.org/source.html offers some good advice... "You should always use PGP/GPG to verify the signatures before using any source code" But where can I find the public key that was used to sign the source? It's not on any key servers I've been able to

2006/1/27, Matthew.van.Eerde@hbinc.com <Matthew.van.Eerde@hbinc.com>: > > I've successfully installed and configured NUT on my test machine and am > moving it into production. > > http://www.networkupstools.org/source.html offers some good advice... "You > should always use PGP/GPG to verify the signatures before using any source > code" > > But where

Hello list members, I am running NUT 2.0.1 on an OpenBSD 3.8 system, using the OpenBSD port for net-snmp-5.1.2p2. The UPS is connected via an AP9606 Web/SNMP card with current firmware, and the LAN. All goes well for a long time, usually more than one month. Then the system starts spitting messages about losing communications with the UPS. A second message about reconnecting follows immediately.

Hi, we do have APC Smart-UPS each with AP9617 and latest FW. As we found out we are not able to shutdown the UPS via SNMP - neither immediately nor delayed. And we cannot set values, but we can read them correctly. So it seems as we are not able to write to the UPS and get back strange errors. root at abex:/etc/nut# upsdrvctl -DDDD shutdown apc10001 Network UPS Tools - UPS driver controller

Attempting to install the SNMP driver on Enterprise SuSE 10.0. The version of NUT is 2.6.0. To begin with, I installed the net-snmp and net-snmp-devel packages, using YAST. If I do this command: net-snmp-config --version --base-cflags --libs The result is: 5.3.0.1 -DINET6 -O2 -fmessage-length=0 -Wall -D_FORTIFY_SOURCE=2 -g \ -fno-strict-aliasing -fstack-protector-all -Dlinux \

I have three APC SmartUPS 5000s. Two of them are AP9617 and one is AP9619. I have a RS-232 connections from my monitor host to all three. All three report status and give information. One of the two AP9617 - ups3-1 - does not shut down when FSD is sent. It did when I first set this system up a year or two ago but it's stopped doing so since then. Resetting the management interface does not

I have been trying to figure out how to do this, anyone know if it's possible? I've tried using the snmp-ups driver and the apcc mibs but I get this error in the logs: Can't connect to UPS [MYUPS] (snmp-ups-MYUPS): No such file or directory I have been able to connect to my ups using the snmp driver successfully. Both use the same AP9606 network card, but have different APP and AOS

I know this isn't exactly the right place to ask, but I figure at least *someone* on this list has done it once. I recently acquired an AP9617 web/snmp management board for my UPS. The web and telnet part of it work great. However, I can't get *anything* from the snmp interface. I've triple-checked the community name and access settings (currently are wide open). I've ensured

New NUT install dealing with three APC Smart-UPS 5000s, two of which have AP9617 and the third has a AP9619 card. The SNMPv3 configurations on all three are exactly the same. This is confirmed by snmpget calls that work just fine: snmpget -Cf -v3 -u [...] -l authPriv -A '[...]' -X '[...]' -a MD5 -x DES [upsname] .1.3.6.1.4.1.318.1.1.1.1.1.1.0 snmp-ups can query all three

I'm trying to get SNMPv3 management working for an APC AP9617 card. It is newly refurbed, running sumx v3.7.2 and aos v3.7.3. In the SNMPv3 user profiles section I have (I don't care about the password leaking, it's temporary): User Name: nut Authentication Passphrase: NutScan at Password43LongerWord Privacy Passphrase: NutScan at Password43LongerWord Authentication protocol:

Just a hunch about your snmpwalk, what happens if you format like this? snmpwalk -l authpriv -v 3 -u user -a MD5 -x DES -A authpassphrase -X privpassphrase {host address} so snmpwalk -l authpriv -v 3 -u nut -a MD5 -x DES -A NutScan at Password43LongerWord -X NutScan at Password43LongerWord apcups Thank you, David Zomaya Tripp Lite ________________________________ From: Nut-upsuser

I need a little help on this problem, please? I include my /etc/apcupsd/apcupsd.conf file is attached. port 3551 udp/tcp has been added to the (running) firewall. My APC is recognized as: APC Back-UPS 450 FW:844.Kld.D USB FW:Kld This from the hardware browser. PS says: root 2419 0.0 0.0 4196 584 ? Ss Mar23 0:09 /sbin/apcupsd -f /etc/apcupsd/apcupsd.conf Is group 2419 the

Hi there, This post has also been posted in the Hardware and General forums but I thought it might be wise to post it here as well! My CentOS 4.3 (upgraded from CentOS 4.2 installed from Linux Magazine's April 2006 issue) server is rebooting spontaneously (over and over again). It started while I was copying from USB-device (iPod) to another USB-device (Freecom Portable-Hard-disk) but it

Here are a series of my recent changes to NUT. The first few in the set are primarily little fixes and improvements. In among those are a few for .gitignore files which of course you can ignore for SVN, and there's one for a commit to a generated file which of course should not be tracked in any VCS. Then there are a couple or three to do with generating the header files used by

Hi Dmitry and the list, would you (or anyone owning such a device) be able to validate the below patch: https://alioth.debian.org/tracker/index.php?func=detail&aid=310613&group_id=30602&atid=411542 Most notably, it's about the paths changes: -#define APCC_OID_IEM_TEMP ".1.3.6.1.4.1.318.1.1.10.2.3.2.1.4.0" -#define APCC_OID_IEM_TEMP_UNIT

Sorry for the lameness, but I need things explained to me very slowly... -----Original Message----- Subject: RE: [Wxruby-users] wxGrid Question > > Yes, grab the latest tarball from the above location. Then, you should > install rubygems if you haven''t already: > http://rubyforge.org/projects/rubygems/ > > That should allow you to easily install rake: >

---------- Forwarded message ---------- Date: Sat, 23 Oct 1999 22:11:13 -0700 (PDT) From: David Cantrell <david@slackware.com> To: slackware-security@slackware.com Subject: CA-99-13: minimal fix for Slackware 3.5 through 4.0 Regarding the recent CERT advisory about WU-FTPD: An alternative minimal fix is available for Slackware versions 3.5, 3.6, 3.9, and 4.0. Users can download this and

After building and bfu''in the lastest ON build, any time I run a dtrace script I get a Seg Fault. Is there a dtrace for dtrace :) Doug root at prae> dtrace -n ''syscall::open*:entry { printf("%s %s",execname,copyinstr(arg0)); }'' Segmentation Fault (core dumped) root at prae> pstack core core ''core'' of 101364: dtrace -n

Hi, Im new to Ruby on Rails, it seems to be really powerfull. I am running Apache 1.3.x and I dont know how to set it up to work with Ruby on Rails. I think the problem is Fast CGI because I dont understand how to set that up. I can''t find anything regarding Fast-CGI in my apache config file. But I find this its some sort of cgi. LoadModule cgi_module libexec/apache/mod_cgi.so

Will I run into any problems mixing ReiserFS and ext3 on my slackware linux box? I'm using ReiserFS and LVM on the current version, thinking of mixing it up a bit with slackware 10, again with LVM. Thanks for any advice! ===== Christopher Mark Conn http://storm.cadcam.iupui.edu/~cmcgoat Austin, Texas, USA