similar to: support for powerware 3110?

Hello, I am attempting to monitor my two Powerware 3110 UPS from Gentoo Linux using nut-2.2.0, kernel-2.6.22.1 via USB. From what I can gather around the net (circa 2005) things with USB on this UPS just didn't work. Has this changed and is there anything I can do to help? My ups.conf contains the following... [ups-router] driver = usbhid-ups port = auto desc =

Here is my ups.conf... [ups-router] driver = usbhid-ups port = auto desc = "Powerware 3110 - Router" [ups-server] driver = usbhid-ups port = auto desc = "Powerware 3110 - Server" Here is the output from upsdrvctl start... Network UPS Tools - UPS driver controller 2.2.0 Network UPS Tools: 0.28 USB communication driver 0.28 -

Ok, I installed the ups, and installed nut, and /proc/bus/usb/devices says this T: Bus=03 Lev=01 Prnt=01 Port=01 Cnt=01 Dev#= 2 Spd=1.5 MxCh= 0 D: Ver= 1.10 Cls=00(>ifc ) Sub=00 Prot=00 MxPS= 8 #Cfgs= 1 P: Vendor=06da ProdID=0002 Rev= 0.01 S: Manufacturer=POWERWARE S: Product=Powerware UPS C:* #Ifs= 1 Cfg#= 1 Atr=80 MxPwr= 20mA I: If#= 0 Alt= 0 #EPs= 1 Cls=ff(vend.) Sub=00 Prot=00

Hello, does NUT support Powerware Prestige EXT 1000VA / PowerWorks A30 models in smart mode? I don't see them mentioned in the compatibility list (only Powerware 3115 and 5119 are there, listed as supported only by the "genericups" driver). Is the protocol known to be compatible with any other, supported UPS types? Thanks, Marek

Hi, OS: FreeBSD 9.0-RELEASE NUT version: nut-2.6.5_1 (installed from ports) UPS: Eaton powerware 5110 Can you help me with this device, please? [root at mail /usr/local/etc/nut]# /usr/local/libexec/nut/usbhid-ups -DDDD -a eaton Network UPS Tools - Generic HID driver 0.37 (2.6.5) USB communication driver 0.31 0.000000 debug level is '4' 0.001239 upsdrv_initups... 0.001958

I tried switching to the USB version of bcmxcp_usb and get this error when I try starting up upsdrvctl or bcmxcp_usb like so: /etc/nut/bcmxcp_usb -DDDD -a powerware -u nut I used this for ups.conf: [powerware] driver = bcmxcp_usb port = auto With the serial/usb dongle, I used this successfully: [powerware] driver = bcmxcp port = /dev/ttyUSB0 What devices does

Hello all! I've been trying to get my UPS working with my OpenBSD stable box and I haven't had any luck yet. dmesg shows that I have something from Powerware usb0 at uhci0: USB revision 1.0 uhub0 at usb0 "Intel UHCI root hub" rev 1.00/1.00 addr 1 biomask f5fd netmask fffd ttymask ffff ugen0 at uhub0 port 1 "Powerware Powerware UPS" rev 0.20/0.50 addr 2 nut version

THE GOOD: NUT is able to communicate with my Powerware 5115A over USB using the bcmxcp_usb driver: ambient.temperature: 38 battery.charge: 99 battery.runtime: 9000 battery.voltage: 27.07 driver.name: bcmxcp_usb driver.parameter.pollinterval: 2 driver.parameter.port: auto driver.version: 2.2.1 driver.version.internal: 0.13 input.frequency: 50.34 input.voltage: 235 output.current: 0.0

Help please on Powerware 3105 serial (aka SOLA 305 here in Australia). Is it best configured as a contact-closure device or do I try and persist to get bcmxcp to work - which it won't so far? Running on SUSE 10.1 Thanks,

Hi, I am wanting to use NUT to connect to an Eaton Powerware 5110 UPS using USB to connect. - I am using NUT 2.0.2 - I have compiled it with USB support - I can see that the UPS is registered as connecting in /var/log/messages eg usb 3-1: USB disconnect, address 3 usb 3-2: new low speed USB device using uhci_hcd and address 4 But I don't know how to progress from here.

Hi, I've got a Powerware Prestige 9 1kVA UPS that seems to not be working with nut. It's not in the current "supported hardware" list, but the old bcmxcp page lists it as being a UPS that speaks that protocol. I have the following in my ups.conf [powerware] driver = bcmxcp port = /dev/ttyS0 desc = "Powerware Prestige 9 EXT" baud_rate = 2400 And when I start the

Hi everyone, Been searching like crazy to find an answer to this. I have even read some of the source code but cannot figure this one out. I have installed nut 2.4.1 on my QNAP 409 Pro. (command: ipkg install nut) I have configured the ups.conf, upsd.conf and upsd.users. When i run "upsdrvctl start" I get the following error messages and output.

Hi all, I've got a Powerware 5110 UPS that I'm trying to set up with nut in Ubuntu. I've installed nut and configured the first two files: $ cat /etc/nut/nut.conf MODE=standalone $ cat /etc/nut/ups.conf [pw5110] driver = bcmxcp_usb port = auto # port = /dev/bus/usb/002/002 When I try to test this configuration with the following command: $ sudo upsdrvctl start pw5110 Network UPS

Hi, I'm having trouble with nut running on feisty. I have a powerware 5110 connected using USB i did an "sudo lsusb -a" before and after i plugged in the powerware usb cable and did a diff on the results of the two which was: -- 322c322 < Port 2: 0000.0100 power --- > Port 2: 0001.0301 C_CONNECT lowspeed power connect -- current ups.conf is: -- [pw5110] driver =

I decided to try this to see if it worked better since Powerware decided to build in some oddball USB protocol instead of using a HID UPS profile, but it doesn't seem to work. The USB/serial dongle is recognized by Linux and added as /dev/ttyUSB0, owned by group "dialout", so I had to add the nut user to the dialout group. In the compatibility list, the proper driver for the

Hi, I'm trying to get a Powerware 3105 UPS working on SuSE 10.0. I have compiled nut from the current Subversion repository. This UPS uses the bcmxcp_usb driver. I cannot get the driver to find the ups on the USB bus. The error message I get is:- -------------- bcmxcp_usb -u nut -DDDDD -a pw3105 -------------------- Network UPS Tools - BCMXCP UPS driver 0.10 (2.1.0) debug level is

Hi, I have an UPS Powerware 5110 ( usb connection ), on Linux OS is Debian 4.0 The /etc/ups.conf file setting is: [myups] driver = bcmxcp_usb port = auto desc = "UPS Powerware 5110 1500 VA" When the daemon starts it displays the following message: "Starting Network UPS Tools: (upsdrvctl failed)." Looking at /var/log/syslog I found the following line

2009/8/28 Thomas Zulliger <Thomas.Zulliger at quiksilver.com.au> > Hi Arnaud > Hi Thomas, > I'm experiencing exactly the same problem > > DNS-323 fun_plug Fonz > nut 2.4.1-1.tgz > powerware 3105 > using BCMXCP_usb > > /mnt/HD_a2/packages # lsusb > Bus 002 Device 001: ID 0000:0000 > Bus 001 Device 002: ID 0592:0002 Powerware Corp. > Bus 001

I am seeing some problems when using the Powerware 5115 UPS when connected to the Patsburg USB controller and would like to know if anyone has a solution. The symptom is that PING messages sent to the bcmxcp_usb driver take as long as 25 seconds to complete. The configuration is a Romley patform (a.k.a., Sandy Bridge + Patsburg) running Debian 6 with 2.6.39 kernel with NUT 2.6.4 in which the

I've got some strange problem with NUT on my 5115 on Debian Etch: ---snip--- $ sudo ./bcmxcp_usb -DDDDDDD -a 5115 Network UPS Tools - BCMXCP UPS driver 0.13 (2.3.0-1181) Warning: This is an experimental driver. Some features may not function correctly. debug level is '7' Can't set POWERWARE USB configuration Unable to find POWERWARE UPS device on USB bus Things to try: -