similar to: Various NUT issues/questions

Hello, we have a MGE Pulsar Evolution 800 connected to a Fedora Core5 Server using a serial cable. Installed and configured properly are RPM versions of nut-2.0.3-0.1.fc5 nut-client-2.0.3-0.1.fc5 nut-cgi-2.0.3-0.1.fc5 which all work (mostly) fine. The server is connected to outlet.0 and properly shuts down when it's loosing power after around 20 minutes. It also boots up whenever the ups

On Fri, Sep 11, 2020, at 4:05 PM, Bartosz wrote: > Dear All, > > Could you please recommend me a UPS with 100% support of the ondelay parameter and NUT compatibility? > > 850 or 1000 VA > > I have the EATON 5E850iUSBDIN UPS and it does not support this parameter so I would like to buy another UPS that for sure will support it. > > Thank you, > Bart Can you tell

Hi, I have recently purchased MGE ellipse 1200 UPS for my home system. Obviously, the choice of this particular brand was mainly dictated by MGE's long-standing support for Linux and NUT project. The fact that the box was clearly the prettiest looking one on the block did help also ;-). I have had NUT tools installed and configured in no time, as I did it numerous times before -- kudos

Hi, I'm a MGE Evolution 650 owner and, after putting in place a basic configuration for controlling my UPS, I'm going to tune a little bit better NUT for my needs. First of all let me describe my little (SOHO) scenario: I have the ISP modem/switch (providing VoIP too, so it's important to keep it running as much as possible), a small low power home server and a much hungrier PC.

I was looking at how other drivers deal with outlet collections, and I noticed some differences between newhidups in 2.0.4 (from Debian's 2.0.4-2.3) and the SVN trunk (rev 723) on an Evolution. Full diff is below, but here are the highlights: * MGE HID 0.9 vs 1.0 * outlet.#.switch seems to have moved to the commands outlet.#.load.{on,off} Then I found this in the ChangeLog: * fix

I am running NUT 2.2.0 compiled from the FreeBSD ports tree. [inchoate 14:50] ~ >upsc ups1 at localhost battery.charge: 59 battery.charge.low: 20 battery.charge.restart: 0 battery.runtime: 6350 battery.type: PbAc battery.voltage: 43.0 driver.name: usbhid-ups driver.parameter.offdelay: 120 driver.parameter.ondelay: 13 driver.parameter.pollinterval: 2 driver.parameter.port: auto driver.version:

Hello nuters, FreeBSD, Ellipse USBS 800, serial line, nut 2.02 everything works fine. But I'm only able to get an automatic shutdown when reaching the built-in 30% level. I the "lowbatt parameter" is set to anything, it's simply ignored. This is a problem as I want to shutdown around 90% to avoid the battery to drain out when multiple shutdowns occur. Any idea ?

Hi, I am trying to talk to an MGE Pulsar Extreme UPS over RS232 with the mge-shut driver but I'm having some problems. It appears to init OK but I can't, say, turn the outlets off, eg.. harrow:~>upsc mge@localhost battery.charge: 78 battery.charge.low: 20 battery.runtime: 05760 driver.name: mge-shut driver.parameter.port: /dev/cuad1 driver.version: 2.0.3 driver.version.internal: 0.65

Hi, I've been using NUT for many years to look after the UPS on my home servers. Originally I was using a Compaq R3000 but that was replaced with an MGE Pulsar Evolution 3000 about a couple of years ago because the Compaq one was just too noisy! I'm just setting up a replacement server and would like to connect it using a serial cable as I've found that the USB connection

Hello ! I've just a problem with upsd/upsmon 2.0.4, please have a look at the upsc command: -------------------- battery.charge: 59 battery.charge.low: 5 battery.runtime: 1312 battery.voltage: 24.0 driver.name: newhidups driver.parameter.port: auto driver.version: 2.0.4 driver.version.data: MGE HID 0.9 driver.version.internal: 0.28 input.frequency: 0.0 input.transfer.boost.low: 184.0

Hello Niels, thanks a lot for this compatibility submission. This is part of the remaining things at Eaton. I've added an entry to the new Hardware Compatibility List: http://new.networkupstools.org/stable-hcl.html BTW, have you tested a shutdown with this unit? Otherwise, you should! thanks again, Arnaud Quette Le samedi 02 octobre 2010 ? 12:42 +0200, Niels Kristian Jensen a ?crit :

Hi, I have a FreeBSD 9.2 system with NUT 2.6.5 (installed via the ports tree) with an MGE Pulsar 1500 connected. A while ago it complained it needed the battery replaced and it was finally replaced last week, however I can't find out how to reset the flag in NUT. I've looked in upsc, upsrw and upscmd but none seem to have a suitable option. The UPS is connected via RS232 and upsc output

Hi, I am trying to talk to an MGE Pulsar Extreme UPS over RS232 with the mge-shut driver but I'm having some problems. It appears to init OK but I can't, say, turn the outlets off, eg.. harrow:~>upsc mge@localhost battery.charge: 78 battery.charge.low: 20 battery.runtime: 05760 driver.name: mge-shut driver.parameter.port: /dev/cuad1 driver.version: 2.0.3 driver.version.internal: 0.65

Hi Dag 2010/2/28 Dag Atle Nettum <dagatle at innit.no> > Hello > > > > I understand you are the project leader of Nut. > > > > In my company we have a Eaton 9135 6000 UPS, we are running NUT 2.4.1 > (Debian squeeze) > > > > The ups is connected with a USB cable but it reports a temperature of 300 > degredes. > > > > Can I send you

On Fri, Sep 25, 2020 at 11:47:42PM +0300, Manuel Wolfshant wrote: > On 9/25/20 1:36 PM, Lionel Élie Mamane wrote: >> On Thu, Sep 24, 2020 at 06:51:23PM +0300, Manuel Wolfshant wrote: >>> On 9/21/20 9:47 PM, Lionel Élie Mamane wrote: >>> We have a HP R/T 3000 G4 UPS; according to the data returned by >>> the usbhid-ups driver, it seems to be a "badge

Hi, I try to install the newhidups driver for a MGE Pulsar M2200 connected to a USB port under Linux Red Hat 4 Upd 4. I have compiled and installed the usb driver (make usb && make install-usb). I followed the instructions in /nut-2.0.5/scripts/hotplug-ng/README abour the /etc/udev/rules.d/025_nut-usbups.rules. The ups is recognized by the kernel: Mar 12 14:52:03 serveur1 kernel: usb

Hi, I try to install the newhidups driver for a MGE Pulsar M2200 connected to a USB port under Linux Red Hat 4 Upd 4. I have compiled and installed the usb driver (make usb && make install-usb). I followed the instructions in /nut-2.0.5/scripts/hotplug-ng/README abour the /etc/udev/rules.d/025_nut-usbups.rules. The ups is recognized by the kernel: Mar 12 14:52:03 serveur1 kernel: usb

On Thu, Sep 24, 2020 at 06:51:23PM +0300, Manuel Wolfshant wrote: > On 9/21/20 9:47 PM, Lionel Élie Mamane wrote: >> We have a HP R/T 3000 G4 UPS; according to the data returned by the >> usbhid-ups driver, it seems to be a "badge engineered" Eaton 5PX >> UPS LI R 3000. >> We have a stubborn "Replace Battery" alarm that stays (...): >> The

Hello, I've installed Nut (2.0.5) on RedHat a week ago, and upsmon seems to generate false alarms every hour: ... Jun 8 06:10:56 nutevalserver upsmon[2849]: UPS usb-mge-evolution at localhost on line power Jun 8 06:35:46 nutevalserver upsmon[2849]: UPS usb-mge-evolution at localhost on battery Jun 8 06:35:51 nutevalserver upsmon[2849]: UPS usb-mge-evolution at localhost on line power

OS version: FreeBSD 8.4-RELEASE-p19 NUT version: nut-2.7.2_6 NUT installation method: from freebsd pkg system Device info: EATON 9SX 5000i, manufacturing date: 05.09.2014 ups.firmware: 9SX5Ki When i try to see battery charge, in output it have not such variable, and i can't control my server and other clients connected to them. Any options cannot power of server. How to see current battery