similar to: How do I resolve comm issues

Hi, FreeBSD 5.4, NUT from ports (2.0.3), serial on /dev/cuaa1, Ellipse 1200 USBS. I set the ups.conf up as : [ellipse] driver=mge-utalk port=/dev/cuaa1 desc="Ellipse" When I go to start it I get : Network UPS Tools - UPS driver controller 2.0.3 Network UPS Tools - MGE UPS SYSTEMS/U-Talk driver 0.87 (2.0.3) Could not get multiplier table: using raw

Dear Sirs, I have an old but very well-working UPS MGE Pulsar ESV8+ Rack. I'd like to use it to power FreeBSD 9.0-Rel server. Of fortunately I have problem with recommended driver - mge-utalk, nut 2.6.4 (installed from FreeBSD Ports). I get messages: Could not get multiplier table: using raw readings. and updateinfo: Cannot update system status I saw similar thread on mailing list with no

Hello, I recently had a failure with my old MGE ESV8 ups, it just died on me so I had to get a new one. I found a MGE ESV8+ cheap and everything seems to work fine with it except the communication with the computer. The old ESV8 (non +) worked fine with NUT after applying some patches I got from the mailing list, but I think they are in the source tree now. I'm using the same cable that

Ah, the perils of auto-upgrades. Last night, Fedora Core 3 upgraded my perfectly working nut installation to 2.0.2. I was informed of that because every xterm in the house (about 8 over a Linux box, two laptops and a G4 server) started beeping at 3:20am and didn't stop until I shut down nut. Keep in mind this configuration has been working for about two years. Here's the messages I get

Hello, I have a MGE Comet S31. I installed nut for Debian/Sarge and configured the mge-utalk protocol. I get the following syslog messages Sep 28 11:10:41 neckarsulm upsmon[25505]: Poll UPS [comet@mastermind] failed - Variable not supported by UPS Sep 28 11:10:46 neckarsulm mge-utalk[25284]: updateinfo: Cannot update ups.temperature Sep 28 11:10:46 neckarsulm mge-utalk[25284]: updateinfo: Cannot

Some one might have answerd this, but I can not find any think yet I am trying to load a SOLA 610 700va ups up and keep getting : --------------------------------- Network UPS Tools - UPS driver controller 2.0.5 Network UPS Tools - MGE UPS SYSTEMS/U-Talk driver 0.88 (2.0.5) .Detected Pulsar ESV11+ on /dev/cuaa0 Network UPS Tools - Best UPS driver 1.03 (2.0.5) Unknown model detected - please

Hi All, I have an mge pulsar esv 14+ rackmount UPS connected via straight through serial cable to a USB to serial adaptor (My motherboard does not have a native RS232 port). I am running Ubuntu Server 9.04 x64, and nut 2.4.1-2ubuntu4 installed via APT. I am getting the error: Poll UPS [ups1 at localhost] failed - Driver not connected My conf files: (ups.conf) [ups1] driver=mge-utalk

Hi, i had purchase a MGE-Ellipse 500 and i'm trying to use the DB9 F / RJ45 cable send by MGE with UPS. Which driver i'm suppose to use: mge-utalk or mge-shut ? When i try mge-utalk i've got this message: # upsdrvctl start Network UPS Tools - UPS driver controller 2.0.0 Network UPS Tools - MGE UPS SYSTEMS/U-Talk driver 0.80.3 (2.0.0) Startup timer elapsed, continuing... and there is

On 18.4.2013 ?. 22:24 ?., Arnaud Quette wrote: > > 2013/4/18 Pladi Computers Ltd. <pladi at lovechnet.com > <mailto:pladi at lovechnet.com>> > > UPS: > http://www.eaton.com/Eaton/ESeriesUPS/DXUPS/index.htm?wtredirect=www.eaton.com/DXUPS > > I have the same problem on two different computers. The first one > is running Ubuntu 12.10 i386 , the

Hi, I'm looking to backup a small network (Hughes DW7000 satellite modem, small consumer grade Internet Broadband router+wireless, Soekris NET4801 single board computer + 4 port lan card, Cisco 2900 switch) and want a small form factor (This is sitting on a small shelf) and light. The main thing I'm running into is that it *HAS* to be serial. (The Soekris only has 1 USB port and I

Hi, Still running into serial issues on the mge-shut with the MGE Ellipse 1200 USBS. I had mge-utalk sort of talking to it, but was told to use mge-shut and get nothing out of it. This is at a remote site that I have to leave tomorrow so if I don't get it running I can't leave it in place. Help? Thanks, Tuc

Hi, After I do a : upscmd ellipse@localhost test.battery.start How do I tell its running, what the status is, etc. Thanks, Tuc

Credit goes to "cppcheck". Signed-off-by: Thomas Jarosch <thomas.jarosch at intra2net.com> --- drivers/mge-utalk.c | 3 ++- 1 files changed, 2 insertions(+), 1 deletions(-) diff --git a/drivers/mge-utalk.c b/drivers/mge-utalk.c index c6114c7..616e2ad 100644 --- a/drivers/mge-utalk.c +++ b/drivers/mge-utalk.c @@ -465,7 +465,8 @@ void upsdrv_shutdown(void) { char

Hi, FINALLY got my UPS working, YEA!!!! But now it brings up even more issues.. (BOOO!!) 1) I'm thinking this is a UPS issue, but when I pull the plug on my UPS, it goes from 100 to 30 in just a short amount of time (Minutes). This causes the machine to shut down. But once it gets to 0, its beeped its little heart out for a few more HOURS providing power to the non-system items perfectly.

Hello My server with another UPS (MGE Pulsar Evolution2200 USB) is OK. All scripts work Is it possible to work with a UPS MGE CometExtrem 6 on serial port Which driver can I use ? I tried with mge-shut ou mge-utalk without any success when I start driver with upsdrvctl with mge-utalk I have (after a long time) Can't connect to UPS [MGE_cometEX] (mge-utalk-MGE_cometEX): No such

Hi everybody, Sorry for the eternity it took to solve the UTalk problems, but I've been busy on so many fronts... I've updated the CVS Testing tree, which will soon become 2.0.3 stable release, with mge-utalk 0.87. This release fixes the UTalk problems you have recently faced. If possible, please test it and report back if it work or not with your unit. To do so: 1) Retrieve the source

Hello, I'm using an MGE Evolution 1500 with a Debian Sarge 2.4.27 smp server. NUT is using the mge-utalk driver. [ups1500] driver = mge-utalk port = /dev/ttyS0 Seens I did a test.battery.start, my UPS goes off (beep!) once per week (same day, same hour). I guess there should be a very easy explanation for this, unfortunatly, I haven't found it yet. I've tried to upgrade

I have an MGE Pulsar Evolution 1100 connected to a Debian box, with nut-2.0.1 (the standard "sarge" packages). I have it connected through USB, and I'm using newhidups. However, about once a day the driver looses contact with the UPS and I have to restart NUT to get it to drop the "data stale" nonsense (it happens more often than this, but most times it recovers without

Hi, I took the advice of Daniel O'Connor, found out what variables I had available to me, and put them in the conf. So now it looks like : [ellipse] driver = mge-shut port = /dev/cuaa0 desc = "UPS" lowbatt = 5 offdelay = 120 let the UPS charge up fully, 24 hours. I plugged a single lamp into it, with a 60W bulb. At 3:40p

Hi, All ! I'm trying to use nut 2.0.5 on FreeBSD 4.11-STABLE with UPS INELT Monolith II 1000LT UPS connected to box with RS-232 cable. In ups.conf: [apc] driver = megatec port = /dev/cuaa1 desc = "UPS" When starting /usr/local/etc/rc.d/nut.sh start got: Network UPS Tools - UPS driver controller 2.0.5 Network UPS Tools - Megatec protocol driver 1.5 (2.0.5) Carlos Rodrigues (c)