similar to: Negative values for ups.delay.shutdown and ups.delay.start

I have been testing out my new MGE Nova 1100 on a system (dual Athlon) running Fedora Core 5 and the newhidups driver seems to be regularly dying. The UPS is the USB model, I have nut-2.0.3-0.1.fc5 and nut-cgi-2.0.3-0.1.fc5 installed. I am running a 2.6.16 kernel. (I haven't upgraded to FC5's 2.6.17 kernel yet as there seem to be some complaints about it.) The driver initially works.

Hi, I've seen a few emails in the archives about problems polling MGE UPSs via USB under FreeBSD, but unfortunately I didn't find a solution in them that works for me. A few details about my setup.. The UPS is a MGE Nova AVR 600 connected via USB to a FreeBSD 6.2 box. I have tried both the nut port (2.0.5) and the svn trunk but have had no success yet. I am running nut as root to

Hi, I've seen a few emails in the archives about problems polling MGE UPSs via USB under FreeBSD, but unfortunately I didn't find a solution in them that works for me. A few details about my setup.. The UPS is a MGE Nova AVR 600 connected via USB to a FreeBSD 6.2 box. I have tried both the nut port (2.0.5) and the svn trunk but have had no success yet. I am running nut as root to

Hello, It is 3 or 4 weeks ago since, i want to set communication with my ups a MGE NOVA 1100 AVR. I do it first with manual configuration but after no success, i prefered to install mgeups-psp package to do it directly. But since when i execute psp, the attempt finish with an "No communication with UPS" error. Same is when i type: mge-shut -u root -DDDDDDDDDD /dev/ttyS0 . I unplog

Have recently purchased a MGE Nova 1100 UPS and am trying to get running on netBSD. Configuration netBSD 3.0 amd64 libusb 0.1.10a nut 2.0.3 Built & installed libusb Built kernel with ugen device and uhid removed Build & install nut-2.0.3 with usb Chmod /dev/ugen1 etc to allow access by nut user. Ups.conf [MGENova] driver = newhidups port = auto

[the mailing list you want is nut-upsuser.] On Mon, Aug 3, 2009 at 8:05 AM, Blagovest Kolenichev wrote: > Hi, all > > I had fail to find in the supported hardware page > > http://www.networkupstools.org/compat/stable.html > > support for "NOVA AVR 625", but see that "NOVA AVR 600 Serial" > is supported. Can you tell us is there a big difference between

Angel Tsankov wrote, On 12/24/2013 1:22 AM: > On 12/06/2013 10:57 PM, Kris Jordan wrote: > > [...] >> (*) Some UPS's do provide extra options to determine when they will >> restore power to load. > > That would be a nice feature. > > Anyway, it is a strange thing that I can set the waiting time for > power to be restored if main power comes back before

I have an MGE Pulsar Evolution 1100 connected to a Debian box, with nut-2.0.1 (the standard "sarge" packages). I have it connected through USB, and I'm using newhidups. However, about once a day the driver looses contact with the UPS and I have to restart NUT to get it to drop the "data stale" nonsense (it happens more often than this, but most times it recovers without

Hello. I am faced with a configuration where the OS (Debian 6.0.8) and the PC shut down before the UPS (MGE Protection Center 675). Also, the UPS restores power to attached devices as soon as main power is back but the PC does not detect power restorations that occur less than a couple of seconds, say 10, after its power supply has been cut. As a result, if main power comes back within 10

On 12/06/2013 10:57 PM, Kris Jordan wrote: > [...] > (*) Some UPS's do provide extra options to determine when they will > restore power to load. That would be a nice feature. Anyway, it is a strange thing that I can set the waiting time for power to be restored if main power comes back before offdelay has elapsed, but the UPS ignores this setting if main power comes back after

Hi, I own one a MGE Protection Center 675. You can change the parameter ups.delay.start into your UPS to set the "Interval to wait before (re)starting the load (seconds)" use upsset to change the value. Regards, Ren? Le 2013-12-06 15:14, Angel Tsankov a ?crit : > Hello. > > I am faced with a configuration where the OS (Debian 6.0.8) and the PC > shut down before

Hello, Ren?. > You can change the parameter > ups.delay.start into your UPS to set the "Interval to wait before > (re)starting the load (seconds)" > > use upsset to change the value. So far, the ups.delay.start parameter in my MGE Protection Center 675 has always been equal to the driver.parameter.ondelay parameter (which equals the ondelay argument in ups.conf).

I have nut 2.6.4-2.3+deb7u1 on debian 7 32bit, with UPS Eaton Nova AVR 1250 connected via USB. It happens several times a day that I get a message about Apr 3 16:41:49 kernel: [422581.049671] usb 5-1: usbfs: USBDEVFS_CONTROL failed cmd usbhid-ups rqt 161 rq 1 len 4 ret -110 Apr 3 16:41:54 kernel: [422586.041057] usb 5-1: usbfs: USBDEVFS_CONTROL failed cmd usbhid-ups rqt 161 rq 1 len 3 ret

Hi, I have an Eaton/MGE EX 11 RT UPS (uses the mge-shut driver) and while I was testing it I found that it would turn back on straight after power was restored. I had a look but I couldn't find a setting which would let me tell it to charge to (say) 50% before turning the load back on. Does anyone know if this is possible? A setting like this would provide some hysteresis for successive

Angel Tsankov wrote, On 12/6/2013 12:31 PM: > Hello, Ren?. > >> You can change the parameter >> ups.delay.start into your UPS to set the "Interval to wait before >> (re)starting the load (seconds)" >> >> use upsset to change the value. > > So far, the ups.delay.start parameter in my MGE Protection Center 675 > has always been equal to the

Hi! We have two MGE Evolution 1100 here, and I want to make use of the powershare outlets to force a particular boot sequence on the machines powered by them. However I'm not sure how to set those variables upon NUT starting, without having to change the init scripts to call "upsrw". Is there some place where I can set them, where they can be read automatically on startup? One of

Hello All, I have a data frame (dput information below) with food item weight for fish species. I need to calculate the Mean proportion by weight of each food item for each specie, as show in solution data frame (dput information below). I use the ddply function (plyr package) in two steps. First calculate the proportion of weight for each individual: step1 = ddply (example, .(ID), transform,

On Apr 3, 2014, at 3:40 PM, Adam Pribyl wrote: > I have nut 2.6.4-2.3+deb7u1 on debian 7 32bit, with UPS Eaton Nova AVR 1250 connected via USB. Which kernel version? > It happens several times a day that I get a message about > > Apr 3 16:41:49 kernel: [422581.049671] usb 5-1: usbfs: USBDEVFS_CONTROL failed cmd usbhid-ups rqt 161 rq 1 len 4 ret -110 > Apr 3 16:41:54 kernel:

-----BEGIN PGP SIGNED MESSAGE----- Hello, I leave a mail here because I can't find any solution in order to get the nut working with this UPS despite I search everywhere on the net. I've bought this UPS recently after that an MGE-UPS Ellipse 1200 USB burn. I've those information about the UPS : Reseller link : http://www.alpha-power-technologie.com/images/GPi-usb.pdf In his

-----BEGIN PGP SIGNED MESSAGE----- Hello, I leave a mail here because I can't find any solution in order to get the nut working with this UPS despite I search everywhere on the net. I've bought this UPS recently after that an MGE-UPS Ellipse 1200 USB burn. I've those information about the UPS : Reseller link : http://www.alpha-power-technologie.com/images/GPi-usb.pdf In his