similar to: Help with newhidups subdriver for Dynex UPS

Displaying 20 results from an estimated 3000 matches similar to: "Help with newhidups subdriver for Dynex UPS"

2005 Aug 02
0
newhidups for APC Back-UPS ES 650
Gentlemen, Please note that what follows pre-dates the latest changes from Arnaud (just thought someone might want to look at these before I can test the latest!). When running newhidups with -D -D -D I saw messages that looked like errors, and it took me a while to understand that they were not really errors. I therefore added two new entries in apc-hid.h, and I modified a couple of diagnistic
2007 Jan 26
1
newhidups output for Geek Squad GS1285U
This took a long time because I had problems with my system. After I reloaded my operating system several times I found I had a bad memory module. Here is the output from newhidups for my Geek Squad GS1285U. It just kept repeating until I hit ctl-z. I think that this means nut will work for this ups. My computer is not powered by the ups yet. I did not want it to be powered down by accident.
2005 Oct 02
0
2.0.3-pre
Gentlemen, I just had time to start looking at the latest version of the development tree. I have built the apc-hid part of newhidups from the development tree and I am in the process of testing it with my "Back-UPS ES 650". As of right now I have incorporated the attached changes to apc-hid.c. I have been using the corresponding changes together with some changes from Arnaud with the
2005 Oct 02
3
more on 2.0.3-pre
Gentlemen, I have now had a chance to run some initial tests of my changes to apc-hid.c of the current development tree. Running newhipups and inspecting the -DDDD output seems to indicate that with the fix below everything seems to work as expected. However, I have not yet shut my system in order to take the UPS out of action so that I can do my various tests with a lightbulb load. I still hope
2020 Oct 23
2
Nut-upsuser Digest, Vol 184, Issue 8
Thanks again for your patience. I'm still learning how to deal with systemctl myself (and starting from, I'm sure, a much lower level of understanding), so if I've neglected to restart or start something, please let me know. I made the change to /etc/nut/upsd.conf. I restarted upsdrvctl, which reported back: Network UPS Tools - UPS driver controller 2.7.4 Network UPS Tools - Generic
2016 Dec 03
2
Problem installing NUT on 16.04
This is new install on Ubuntu 16.04, using packages from Synaptic, *Network UPS Tools upsd 2.7.2 I am getting these messages in the terminal: Broadcast message from nut at amethi (somewhere) (Fri Dec 2 12:33:03 2016): UPS CyberUPS1 at localhost is unavailable I am still unclear on where to set when nut shutdowns system. I see nut-client and nut server are automatically starting from SystemD.
2006 Aug 02
1
nut-usb fink version
Charles Lepple wrote: > On 8/2/06, Didrik Pinte <dpinte@itae.be> wrote: > > Le mercredi 02 ao=FBt 2006 =E0 08:08 -0400, Charles Lepple a =E9crit : > > > On 8/2/06, Didrik Pinte <dpinte@itae.be> wrote: > > > > Can you start the driver like this: "/sw/bin/newhidups -u root -DDD" > > > and paste some of the output? > > > > Here
2020 Oct 21
1
Can't get CyberPower UPS to work with Raspberry Pi 4
I've searched the listserv archive, to no avail, so I hope I'm not duplicating a previous problem. I am anxious to get this working, so I'm open to uninstalling what I have and starting over. One note which may not be meaningful is that this UPS pre-dates the Raspberry Pi I've got connected to it, and I used to use it with the CyberPower software, which requires logging in with a
2014 Mar 24
2
Incorrect Values From usbhid-ups
I recently purchased a CyberPower CP1500PFCLCD UPS as a replacement UPS for a headless server running Slackware 14.1 with the 3.10.7 kernel. I then downloaded the NUT 2.7.1 tarball on the server and following the directions installed the software. The installation went well and the UPS will shutdown the server using the forced down test and then it powers back up as it should. The
2010 Dec 16
6
CyberPower Value 2200E-GP
I've just set up a CyberPower Value 2200E-GP on a system running Lucid AMD64, with the current NUT package via apt-get, and it seems to be working fine for me with the usbhid-ups driver, so I guess it can go in the HCL? I'm using the system to host several virtual servers under KVM, and to make things simple I set it up to hibernate rather than shutdown, that way all the guest OS
2006 Oct 18
2
newhidups with APC Smart-UPS 1500
I tested your fix (newhidups -DDD /dev/null) using both and APC Back-UPS 350 an APC Smart-UPS RT 2000 XL. No more segmentation fault due to the fixed-size array. ~Jacob -----Original Message----- From: nut-upsdev-bounces@lists.alioth.debian.org [mailto:nut-upsdev-bounces@lists.alioth.debian.org] On Behalf Of Peter Selinger Sent: Monday, October 16, 2006 12:12 PM To: Schmier, Jacob Cc: NUT
2005 Jul 22
1
Another HID USB UPS
Gentlemen, I have a new HID USB device, that seems to be quite similar to the currently supported APC HID UPS. I append the dump-tree output, and would much appreciate advice on how to proceed. Certain entries for the current device are not available, but maybe there are some replacements that could be used. This may of course require a new table in apc-hid.h, and I would prefer not to do this
2008 Dec 31
2
Unknown product ID for Tripp-Lite UPS (SU1500RTXL2UA)
To all, I attempted to configure the UPS tools for the Tripp-Lite SmartOnline 1500VA 2U rackmount UPS. I followed the instructions from the 'upsdrvctl start' output and posted the diagnostic information below. Is my UPS using an unknown product ID as reported? From the mailing list archive, I have found another posting for the same UPS with device model '09AE/4003', whereas
2019 Dec 08
3
Tripp Lite SMART1500LCD repeatedly disconnecting and reconnecting
My UPS is connected to a Raspberry Pi by USB. After a few hours of working, the service fails. Looking at kernel messages I noticed that the device is repeatedly disconnecting and reconnecting. I have tried using a different USB port and using a brand new USB cable. I have not had success by changing config parameters like pollfreq/pollinterval/etc. What is causing the UPS to keep disconnecting?
2007 Feb 26
1
Tripp Lite USB UPS
Hello all, About a month ago Peter and Charles were kind enough to try to help me with getting a Tripp Lite USB UPS to work with NUT. I reported quite a bit of initial success, and then other things here fell apart. Between work, fence building and a week-long out of town business trip, I have had to drop this from my list of things to do lately. I am back at it, and I believe I will have
2017 Aug 21
5
TrippLite SMART1500LCD no delay before ups shutdown.
Hello, I am hoping someone can point me in the right direction. I am setting up a new UPS, most things seem to be working except the UPS turns off immediately during a test shutdown using///"//upsmon -c fsd".//No delay before the UPS turns itself off leaving no time for the server to shutdown properly. I have attempted to set the delay higher using "upsrw -s
2007 Dec 05
2
Crash when I start driver
It's been a while since I tried to use NUT, so I thought I would give it another try. Big trouble. The UPS is a Tripp-Lite AVR 550U. It has only a USB connector. The computer is running Red Hat Enterprise Linux 4. I just installed NUT version 2.2.0. I'm going through the steps in the INSTALL document. # cat ups.conf [igor] driver = usbhid-ups port = auto
2005 Aug 26
0
NUT patches
Charles Lepple wrote: > > would you mind forwarding (to either me, or the list) the .txt file > showing the hidparser bug? I am trying to revamp libhid's hidparser, > and it would be helpful to have the descriptor. The text file is contained in the tarball on the patch tracker, at
2017 Dec 18
2
Tripp-Lite BCPERS450 shutdown/restart problems
I have a Tripp-Lite BCPERS450, connected to a system running Ubuntu 16.04.3 LTS and NUT 2.7.2-4ubuntu1.2. I had to make my own /lib/systemd/system-shutdown/nutshutdown, but now everything is working except for powering on and off the UPS. Regardless of the settings of offdelay and ondelay in upsconf, and regardless of whether the AC power is on, when I say "upsdrvctl shutdown" the UPS
2020 Jun 28
0
AVR750U Low Power not Triggering Shutdown
On 6/28/20 4:25 AM, Scott Colby wrote: > Hello, > > I am having difficulty using NUT to shut down my Netgate SG-1100 > (a pfSense router) when the power level of the UPS gets critically > low. > > Here is some relevant information: > - OS: pfSense 2.4.5-RELEASE-p1 (FreeBSD 11.3-STABLE) > - NUT version: 2.7.4 > - Installed from: pfSense package 2.7.4_7 > - UPS: